0% found this document useful (0 votes)
8 views4 pages

IDNetbroS1410 A4

Uploaded by

Gabriel Santos
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
8 views4 pages

IDNetbroS1410 A4

Uploaded by

Gabriel Santos
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Building safety.

IDNet� Analogue
Addressable Devices

Features General
• Supported by SIMPLEX 4100U/ES Series CIE IDNet communication is provided by the SIMPLEX
4100U/ES Control and Indicating Equipment (CIE)
• CIE displays device location and status and is the next generation of addressable device
• Individually addressable communications communications, improving upon the original
over a single cable pair MAPNET II communications protocol. The IDNet
protocol and hardware enhancements support
• Zone adaptor modules provide addressable
interface to conventional circuits up to 250 addressable devices on a single cable
pair and can support additional device types and
• IDNet digital protocol communications different operations.
• Convenient DIP switch address selection IDNet communicating devices individually
• Supports up to 250 addressable devices per annunciate identity and accurate status to the
loop 4100U/ES CIE Applications include monitoring of
• Range of enclosures to suit, with a covers sprinkler pressure switches, flow switches and
incorporating an LED viewing window valve monitor devices, interfacing of conventional
detectors and addressable monitoring and control
(voltage free) for AS 1668 applications.
The majority of IDNet devices are loop powered
requiring a single cable pair for operation by the
CIE.
4090-9002 Relay IAM (Individual Addressable Module)

The 4090-9002 Relay IAM allows the CIE Technical Specification


to control a remotely located Form “C” Comms Power1 24 to 40Vdc w/data
Relay contact using IDNet addressable Relay Contact Ratings SPDT
communications for both data and
0.5A @120VAC2
module power. Typical applications are for
switching local power for control functions 2A@24Vdc2
such as magnetic door holders, or control 1A@24Vdc3
of HVAC components, pressurisation fans, Current Limited Operation 1k8/4k7 0.5W
dampers, etc. Relay contact status is also Dimensions (HWD) 105x105x35mm
communicated to the CIE. The address Ambient Temperature 0 to +49°C
is set by DIP switch under the resealable
Relative Humidity 10% to 93% (n/c)
label.
Part Number 4090-9002
1. IDNet communications 2. Transient suppressed load
3. Inductive load
Note: Loop powered 2 wire device

4090-9007 Signal Relay IAM (Individual Addressable Module)

The 4090-9007 Signal Relay IAM provides Technical Specification


a supervised, addressable interface Comms Power1 24 to 40Vdc w/data
to conventional warning devices such Operating Current 170mA
as sounders or strobes. It requires a
Relay Contact Ratings SPDT
supervised power supply or compatible
signal input for powering the externally 0.5A @120VAC2
connected loads. 2A@24Vdc2
• Provides a single switched branch with 1A@24Vdc3
supervision Current Limited Operation 1k8/4k7 0.5W
• Contact is fused at 0.5A for 30V DC EOLR 10k Ohm
or 70V AC using standard 20 x 5mm Dimensions (HWD) 105x105x35mm
cartridge fuse
Ambient Temperature 0 to +49°C
• DC loads must be diode isolated
• Supervision cannot be disabled Relative Humidity 10% to 93% (n/c)
• The supply side and the internal fuse Part Number 4090-9007
are not supervised by the Signal IAM 1. IDNet communications 2. Transient suppressed load
3. Inductive load
• Signal IAM is not suitable for switching
100V audio signals
Note: Loop powered 2 wire device

4190-9050 Analogue Monitor Zone (AMZ) Adaptor Module

SIMPLEX AMZs provide an accurate, Technical Specification


multi‑featured 4-20mA interface for Operating Voltage1 18 to 32Vdc
connecting analog sensors to Simplex Sensor Output Switched input voltage
addressable fire detection panels. Sensor Current 400mA (max.)
The panel monitors the sensor and Basic AMZ Current 30mA
annunciates whenever a selected Sensor Loop Current 20mA (max.)
threshold level or fault condition is Fault Current 5mA
observed. Typical applications include: gas, 2098-9808 LED Annun. 3mA
air, liquid temperature, humidity, and air Dimensions (HWD) 105x105x35mm
velocity sensing. The maximum distance Ambient Temperature 0 to +38°C
from AMZ to a sensor is 1km. Each AMZ Relative Humidity 10% to 90% (n/c)
requires an address and up to 100 AMZs Part Number 4190-9050
can be connected per panel. 1. MAPNET II communications
Note: Loop powered 2 wire device

4090-9051 Supervised IAM (Individual Addressable Module)

The 4090-9051 Supervised IAM has both Technical Specification


power and communications supplied Comms Power1 24 to 40Vdc w/data
by a two-wire IDNet circuit. It provides Operating Current 170mA
a single address for an initiating device Supervision Resistor 6k8 Ohm 0.5W
(such as detector alarm contacts) or
Current Limited Oper.2 1k8/4k7 0.5W
multiple devices at the same location
by monitoring N/O dry contacts and the Dimensions (HWD) 40x40x14mm
wiring to an end of line resistor. It is Ambient Temperature 0 to +49°C
housed in an encapsulated housing with Relative Humidity 10% to 93% (n/c)
flying leads. Part Number 4090-9051
This allows dual functions such as tamper 1. IDNet communications
switch and water-flow switch monitoring 2. Available only with IDNet
to be done by a single addressable point. Note: Loop powered 2 wire device

IDNet Analogue Addressable Devices


4090-9101 ZAM (Zone Adaptor Module)

The 4090-9101 Monitor ZAM allows a Technical Specification


2-wire circuit of conventional smoke or Comms Power1 24 to 40Vdc w/data
heat detectors to be interfaced on to the Operating Voltage 18.9 to 32Vdc
IDNet loop.
ZAM Current @ 24VDC2
Up to 20 conventional heat and smoke Quiescent 16mA max.
detectors can be monitored by a 4090-
Alarm 72mA max.
9101 Monitor ZAM. The address is set by
DIP switch under the resealable label. Supervision Resistor 3k3 Ohm 1W
Dimensions (HWD) 105x105x35mm
Note the 4090-9101 requires a separate
24Vdc power supply to power the Ambient Temperature 0 to +49°C
conventional circuit. Relative Humidity 10% to 93% (n/c)
Part Number 4090-9101
1. IDNet Communications 2. Actual current value is
determined by total device requirements

Note: Loop powered 2 wire device

4090-9116 Addressable Line Isolator

The 4090-9116 Isolator provides IDNet Technical Specification


communications isolation, improving Comms Power1 24 to 40Vdc w/data
installation convenience and system Dimensions (HWD) 105x105x35mm
integrity. Circuit isolation can be selected
manually, or automatically when an output Ambient Temperature 0 to +49°C
short circuit is detected and the condition Relative Humidity 10% to 90% (n/c)
is reported to the CIE. If the output wiring Part Number 4090-9116
is acceptable, the isolator will connect the
rest of the circuit. If the output wiring is 1. IDNet communications
shorted, the isolator remains isolated.

4090-9117AU Addressable Power Isolator

The 4090-9117AU Power Isolator provides Technical Specification


monitoring and short circuit protection for
Comms Power1 24 to 40Vdc w/data
24Vdc power wiring to IDNet addressable
Current Rating 2A@32Vdc max.
devices. In the event of a short circuit,
Input Current 10mA@24Vdc
an electronic switch isolates both power
Dimensions (HWD) 105x105x35mm
circuit conductors and reports its status to
Ambient Temperature 0 to +49°C
the CIE. This function can also be selected
Relative Humidity 10% to 90% (n/c)
from the CIE.
Part Number 4090-9117AU
1. IDNet communications

4090-9118 Relay IAM with T-Sense Input

The 4090-9118 Relay IAM with T-Sense Technical Specification


allows a 4100U/ES IDNet communication Comms Power1 24 to 40Vdc w/data
channel to monitor two input contact Relay Contact Ratings SPDT
closures with one point and control an 0.5A @120VAC2
output relay with the other point, yet 0.25A@120VAC3
occupy a single loop address. Power is 2A@30Vdc 2
supplied from the IDNet communications 1A@30Vdc3
channel, eliminating the need for separate Input N/O, dry contacts
power wiring. The input circuit and relay Current Limited Operation 1k8/4k7 0.5W
operation are controlled independently and Dimensions (HWD) 105x105x35mm
may be disabled separately. Applications Ambient Temperature 0 to +49°C
include water flow and tamper switch Relative Humidity 10% to 90% (n/c)
monitoring and control and damper Part Number 4090-9118
position monitoring and control 1. IDNet communications 2. Resistive Load
3. Inductive Load
Note: Loop powered 2 wire device

IDNet Analogue Addressable Devices


4090-9119 Relay IAM with Unsupervised Input

The 4090-9119 allows a 4100U/ES IDNet Technical Specification


communication channel to monitor an Comms Power1 24 to 40Vdc w/data
unsupervised input contact with one Relay Contact Ratings SPDT
point and control an output relay with the non power limited 0.5A @120VAC2
other point, yet occupy a single address. 0.25A@120VAC3
The input circuit and relay operation are power limited 2A@30Vdc 2
controlled independently and may be 1A@30Vdc3
disabled separately. Module power is Input N/O, dry contacts
supplied from the IDNet communications Dimensions (HWD) 105x105x35mm
channel eliminating the need for separate Ambient Temperature 0 to +49°C
power wiring. The address is set by DIP Relative Humidity 10% to 95% (n/c)
switch under the resealable label. Part Number 4090-9119
1. IDNet communications 2. Resistive Load
3. Inductive Load
Note: Loop powered 2 wire device

4090-9120 Six Point I/O Module with T-Sense Inputs & Relay Outputs Module
The 4090-9120 allows 4100U/ES IDNet Technical Specification
communication channel to monitor four Comms Power1 24 to 40Vdc w/data
T-sense input circuits and control two Operating Voltage 18 to 32Vdc
output relays from a single module Operating Current 30mA@24Vdc
requiring a single address. Power is Contact Ratings SPDT
supplied by a separate (listed) 24Vdc Non-power limited 0.5A @120VAC2
power supply. The input circuits and 0.25A@120VAC3
output relay operation are controlled Power limited 2A@30Vdc2
independently and may be disabled 1A@30Vdc3
separately. Point association is determined Supervision Resistor 6k8 Ohm 0.5W
at the 4100U/ES host panel. Each of the Current Ltd Operation 1k8/4k7 0.5W
four input circuits are monitored via an Input N/O, dry contacts
end-of-line resistor and can differentiate LED Output 24Vdc (ext. PSU)
between a short circuit contact closure Dimensions (HWD) 105x105x35 mm
and a current limited contact closure. Two Ambient Temperature 0 to +49°C
input supervision resistors are required per Relative Humidity 10% to 90% (n/c)
T-sense input. Part Number 4090-9120
1. IDNet communications with data
2. Resistive Load 3. Inductive Load
Note: 4 wire device; requires separate 24Vdc and IDNet
communication loop

4099-9701 Manual Call Point

The 4099-9701 addressable Manual Call Technical Specification


Point (MCP) provides a means to manually Comms Power1 24 to 40Vdc w/data
initiate a fire alarm condition to the 4100U/ Dimensions (HWD) 86x87x35mm
ES CIE via the IDNet channel. The IDNet Ambient Temperature -9°C to +70°C
channel provides the communication Relative Humidity 10% to 95% (n/c)
link and power between the MCP and ActivFire listed afp-1691
CIE. Activation of the MCP requires the Part Numbers
frangible element to be broken, causing MCP & Backbox 4099-9701
microswitch contacts to close. The MCP is Spare Backbox SR3T-P
reset by fitting of a replacement frangible Spare Glass (Pk 10) SU0609
element.
1. IDNet communications

Tyco Fire Protection Products


Level 3, 95 Coventry Street
Southbank VIC 3006
Tel : 1300 725 688
Fax : +61 3 9313 9709
Email : [email protected]

Form No. IDNetSBRO1411


SIMPLEX is a trademark of ADT Services GmbH or its affiliates. MAPNET II, SAFELINC, TRUEALARM, TRUESTART are
trademarks of ADT Services AG or its affiliates. TYCO is a trademark of Tyco International Services GmbH. Windows is a
registered trademark of Microsoft Corporation in the United States and other countries. © 2014 Tyco Australia Pty Limited.
A.B.N. 80008399004. Unauthorised use of trademarks is strictly prohibited. Printed November 2014

You might also like