I have received a lot of requests to edit this document, if you have something useful to add, please send the

info in a PM to me on FORScan and I will get it added. I will not be adding anyone due to people vandalizing this.
FORScan: MuddledGuy
This was copied from the 2017 Super Duty Spreadsheet, some of these things may NOT be compatible with the 2017 Focus ST, so please make
NOTE:
sure to read Status!!!
Detailed installation and setup instructions are on the 'Setup Instructions' tab below. When FORScan is completely installed and setup,
NEW USERS READ FIRST:
review the tutorial document linked in the FORScan Training section BEFORE making any changes. Don't forget to backup your modules first!
(Ignore if FTE/FORScan
Feature Name Module Key Position New Value Notes Status
different on 1 - Standard Ford logo Member
Sync3 Boot Splash Screen APIM 7D0-02-01 xxxx x1xx xxxx xxxx xBxx xxxx MuddledGuy Working
4 - LincolnSirius
Removes Presidential
as a media source in Sync. If * is A change to 8, if 2 change to 0. Change does
Remove Sirius from Sync APIM 7D0-01-01 *xxx xxxx xxxx 8xxx xxxx xxxx Texmudder Working
not take effect immediately. Turn car off, open and shut door, wait 30 seconds and restart.
EVERYTHING BELOW IS FROM THE 2017 SUPERDUTY SPREADSHEET, IT MAY OR MAY NOT WORK, AND I AM NOT RESPONSIBLE FOR ANY
NOTE:
DAMAGES CAUSEDthe
This disables BYdouble
THE FOLLOWING.
honk when walking away from truck with engine running and key switch.
Double Horn Honk Disable BdyCM as built726-41-02 xxx1 xxxx xxxx xxx0 xxxx xxxx fob
Thisinallows
pocket. Recommended
LED to implement
fog lights to stay the Secure
on when high Idlealso
beams are (Police Mode)
turned on. feature
This codeto prevent
has switch.
Fog Lights with High Beam
BdyCM as built726-27-01 xxxx xxx1 xxxx xxxx xxx0 xxxx unauthorized
been confirmed driving away
to work without
with the key fob.
some halogen headlght trucks also. Also known as Bambi switch.
LEDLights
Fog and some
withHALOGEN
High Beam This allows Halogen fog lights to stay on when high beams are also turned on. Also known KubotaOrange
BdyCM as built726-27-01 x0xx xxxx xxxx mode (to see deer better).
x1xx xxxx xxxx Display exact termperatures above the gauge on the center cluster. Replace ** with E5 with
HALOGEN as Bambi mode (to see deer better). 76
Show Temps on
Heated and Cooled Gauges
Seats IPC 720-07-01 xxxx xEA xxxx xxxx x**x xxxx brake controller, 65 if no brake controller. A5 adds temps above gauges without adding
4 = No on screen heated/cooled seats on any screen, heated wheel is in top left.
Icons on Home and Climate APIM 7D0-01-01 xxxx xxxx x4xx xxxx xxxx x*xx boost gauge and boost data to menus. AllGoNShow
Fog Light Switches Off 5 = Unknown
Confirmed on LED and halogen headlights/fog lights.
Screens BdyCM as built726-28-02 xxxx x0xx xxxx xxxx x1xx xxxx AllGoNShow
w/Blinker
Disable Door Lock Horn 0 (Default Operation - Fog Lights Constant), 1 (Fog Lights Switchback w/Blinker)
BdyCM as built726-38-02 xxx1 xxxx xxxx xxx0 xxxx xxxx 1 (Enabled - Default), 0 (Disabled) AllGoNShow
Honk Prevents vehicle transmission from shifting out of Park without passive key inside vehicle
Secure Idle (Police Mode) BdyCM as built726-42-01 x0xx xxxx xxxx x1xx xxxx xxxx Default value does not remember either high beam or fog light status on key off/on. AllGoNShow
Remember Fog Lights on (Shifter Locked w/No Key Detected message) 0=Disabled 1=Enabled
BdyCM as built726-27-01 xxxx x1xx xxxx Headlight
xxxx xxx0 xxxx Default switch
value doesinnot
Auto position.either
remember Restores previous
high beam orsetting only
fog light if lights
status are off/on.
on key needed on AllGoNShow
Startup
Remember Fog Lights and
BdyCM as built726-27-01 xxxx x1xx xxxx xxxx xxx0 x1xx next startup.
Headlight switch in Auto position. Restores previous setting only if lights are needed on AllGoNShow
High Beams onRecalibration
Speedometer Startup 900 miles. This is a small change. Larger tire size changes do calibrate the speedometer but KubotaOrange
BCM 726-12-01 xxxx xx00 xxxx xxxx xx4C xxxx next startup.
for Different
Sync Tire Size
3 Boot Screen a check engine light will persist." The following can be used for a slightly larger calibration 76
APIM 7D0-02-01 xxxx x1xx xxxx xxxx x7xx xxxx GT350 Boot Screen Animation *Sync 3.0 only RebelZ
Animations
Sync 3 Boot Screen
APIM 7D0-02-01 xxxx x1xx xxxx xxxx x9xx xxxx GT350 Boot Screen Animation *Sync 3.0 only RebelZ
Animations
Sync 3 Boot Screen
APIM 7D0-02-01 xxxx x1xx xxxx xxxx x5xx xxxx Raptor SVT Boot Screen Animation *Sync 3.0 only RebelZ
Animations
Sync 3 Boot Screen
APIM 7D0-02-01 xxxx x1xx xxxx xxxx x6xx xxxx Mustang Boot Screen Animation *Sync 3.0 only RebelZ
Animations
Sync 3 Boot Screen APIM 7D0-02-01 xxxx x1xx xxxx xxxx x4xx xxxx Lincoln Presidential Boot Screen Animation *Sync 3.0 only RebelZ
Animations BCM 726-31-02 xxxx 07xx xxxx Fixes Incorrect Color Choices When Using Lincoln Theme Livinitup
Sync 3 Boot Screen
APIM 7D0-02-01 xxxx x1xx xxxx xxxx x8xx xxxx Vignale Boot Screen Animation *Sync 3.0 only RebelZ
Animations
Sync 3 Boot Screen
APIM 7D0-02-01 xxxx x1xx xxxx xxxx x5xx xxxx Raptor Ford Performance Boot Screen Animation *Sync 3.0, Sync 2.2 RebelZ
Animations
Sync 3 Boot Screen
APIM 7D0-02-01 xxxx x1xx xxxx xxxx xCxx xxxx RS Boot Screen Animation *Sync 3.0, Sync 2.2 RebelZ
Animations
Sync 3 Boot Screen
APIM 7D0-02-01 xxxx x1xx xxxx xxxx xBxx xxxx RS Boot Screen Animation *Sync 3.0, Sync 2.2 RebelZ
Animations
Sync 3 Boot Screen
APIM 7D0-02-01 xxxx x1xx xxxx xxxx xDxx xxxx RS Boot Screen Animation *Sync 3.0, Sync 2.2 RebelZ
Animations
BCM 726-17-01 0000 0000 00450101 0101 014A
Allows front windows to open/close with remote button. To open windows, press the
BCM 726-17-02 0101 0101 014B0101 0101 014B unlock button once on fob, then press and hold the unlock button again until front windows
BCM 726-30-01 0001 0000 005F0101 xxxx xxxx begin opening. To close windows, press and hold the lock button for approximately 5 RebelZ
Global Window Open/Close
DDM 740-05-01 9A00 E7 Dxxx xxxx xxxx seconds and release when windows begin to close. Window movement can be interrupted
at any time by pressing either the lock or unlock buttons.
PDM 741-05-01 8A00 D8 Dxxx xxxx xxxx
Adds new menu item under Advanced Settings/Vehicle/Windows to enable Remote Close.
IPC 720-02-01 3xxx xxxx xxxx 7xxx xxxx xxxx KYLongRifle
Remote Open or Close can be enabled and disabled using the checkboxes.
Disable Panic Alarm Horn BCM 726-01-02 xxx0 xxxx xxxx xxx1 xxxx xxxx Replace
Disablesthetheasterisk
horn whenwithpressing thefollowing:
one of the panic button on key
0=Panic fob. button
alarm Lights will stilldisabled,
on fob flash. Livnitup
Panic Alarm Button Press
BCM 726-37-01 xxxx xxx2 xxxx xxxx xxx* xxxx 1=Panic alarm button on fob requires 2 presses, 2=Panic alarm button on fob requires Livnitup
Count
Enable/Disable Spot Lights BCM 726-56-01 xxxx x1xx xxxx xxxx x0xx xxxx single press to
1 for enable, activate.
0 for disable Livnitup
Disable Tire Pressure
BCM 726-08-01 x1xx xxxx xxxx x0xx xxxx xxxx HSWM
1 for enable, 0 forSteering
is Heated disable Wheel Module. Replace the asterisk with one of the following: Livnitup
Monitor
Timeouts for Heated
HSWM 714-01-01 *xxx xxxx xxxx *xxx xxxx xxxx 1=Timeout disabled, 8=5 mins, 9=10 mins, A=12 mins, B=15 mins, C=18 mins, D=20 mins, Livnitup
Steering Wheel
Parking lamps on with low Enables parking lamps while headlights are on low beam when in DRL (daytime running
BCM 726-26-02 x0xx xxxx xxxx x1xx xxxx xxxx E=25 mins, F=30 mins Livnitup
beams for
Remove CDDRL
Option from lights).
APIM 7D0-04-01 x1xx xxxx xxxx x0xx xxxx xxxx Remove the CD player from source in the Sync screen Livnitup
Sync
Courtesy Lamps Ramp
BCM 726-32-02 xx** xxxx xxxx Courtesy Lamps ramp down duration (seconds converted to hex) Livnitup
Down
Courtesy Lamps Ramp Up BCM 726-32-02 xxxx xx** xxxx Courtesy Lamps ramp up duration (seconds converted to hex) Livnitup
Courtesy Lamps
BCM 726-31-01 xxxx x*xx xxxx Courtesy Lamps Cfg: 0=immediate, 1=Theater Dimming Livnitup
Configuration Approach (Puddle) Light Show Max Time (seconds converted to hex). When truck unlocked
Puddle Lights Show Time BCM 726-31-01 xxxx xxxx **xx Livnitup
via fob.
Gal, 7 65=50 Gal, 8 22=55 Gal (This parameter is programmed to accept 4 digit Liters in this
Change Fuel Tank Size IPC 720-03-01 xxx* **xx xxxx xxx* **xx xxxx KYLongRifle
format XXX.x 55gal converts to liters of 208.198L so 208.2L rounded then drop the decimal
Driver Seat Belt Chime
IPC 720-01-01 xxxx xx6x xxxx xxxx xx2x xxxx Number 2 in this position disables the chime on the driver seat jjmcc2
Disable
Passenger Seat Belt Chime
IPC 720-01-01 xxxx xx4x xxxx Number 4 in this position disables the chime on the passenger seat jjmcc2
Diable Number 0 in this position disables the chime on the driver and passenger seats. NOTE: Seat
Disble all Seat Belt Chimes IPC 720-01-01 xxxx xx0x xxxx jjmcc2
belts can be disabled via instructions in the owners manual
DDM 740-03-01 x8xx xx Autofold mirrors via unlock/lock on fob. ** Tow mirrors require swapping pins 18 & 19 on
Autofold/Unfold Mirrors via DDM 740-12-01 Fxxx or FCxx mirror connector. See link: http://www.f150forum.com/f118/tow-mirrors-auto-fold-mod-
hollapm
Lock/Unlock on Fob PDM 741-03-01 x8xx xx pictures-365884/. Fxxx works on trucks with 2 key fobs but FCxx is required if using 3 or 4
PDM 741-12-01 Fxxx or FCxx key fobs.
DDM 740-03-01 x84x xx Autofold mirrors - Lincoln Style (doesn't unfold/fold with unlock/lock on fob...requires
DDM 740-12-01 Fxxx or FCxx opening/closing door).
Autofold/Unfold Mirrors
** Tow mirrors require swapping pins 18 & 19 on mirror connector. See link: hollapm
(Lincoln Style) PDM 741-03-01 x84x xx http://www.f150forum.com/f118/tow-mirrors-auto-fold-mod-pictures-365884/. Fxxx
PDM 741-12-01 Fxxx or FCxx works on trucks with 2 key fobs but FCxx is required if using 3 or 4 key fobs.
7D0-01-02 0xxx xxxx xxxx
Sync 3 Theme - Ford GT
APIM 7D0-02-01 xxxx xDxx xxxx Changes the Sync 3 screens to a GT theme. Splash screen will change to GT. Livinitup
(Blue)
7D0-03-01 xxxx x4xx xxxx ingition power to time out and then turn the radio back on with the RADIO power button.
Increase radio on time after
APIM 7D0-01-01 xx2x xxxx xxxx xx6x xxxx xxxx Alternatively, after turning off the ignition, open and close any door to disable accessory Livinitup
truck shut down camera error afterthemaking this modification.
Add DPF Filter % to screen IPC 720-07-02 x7xx xxxx xFxx xxxx power. Then press radio power button to turnToradio
avoid that,on.
back make your
It will update
now stay onaccording
for the screwy
Turns off the timeout
to the following: onoriginal
If your the power points
default in the
value is 0,truck. Battery
change Monitoring
to 8; if System
1, change to 9; if 2(BMS)
then A;
Power Point Timeout
BCM 726-39-01 xxxx x1xx xxxx xxxx x0xx xxxx will override unless disabled. This feature has had multiple confirmations but also failed on Livinitup
DisablePoint Timeout 4
Power vehicle is shutDifferences
down. After four hours the power points will timeout and stop supplying
BCM 726-39-01 xxxx x1xx xxxx **** xxxx xxxx other trucks. are unknown. manowell
Hours Monitoring System Disables
voltage tobattery
pluggedprotection system.
in devices. Electrical
This feature hassystems will remain
had multiple on and vehicle
confirmations but alsobatteries
failed on
Battery
BCM 726-04-01 xxx1 xxxx xxxx xxx0 xxxx xxxx can drain completely. THIS MAY NOT WORK. The default value is already 0, not 1 as shown. Livinitup
(BMS) Disable
Daytime Running Lights 726-45-01 xxxx 7Fxx xxxx Waiting
Allow additional
DRLBeams
choices updates.
below: DanMc85 &
BCM 40 = Low and Dedicated DRL Lights
(DRL) 726-50-01 XXxx Hex addition of all the choices above: 10+01+02+04+08+20+40=7F Livinitup
726-26-02 x1xx xxxx xxxx
Outer halo lights as DRLs (no low beam, no turn signals). Confirmed on F150s but waiting
Outer Halo Lights as DRLs BCM Livinitup
726-50-01 017F confirmation on SDs
Halogen to LED Headlight Excellent tutorial that goes beyond the instructions provided here: https://www.ford- Livinitup &
BCM 726-26-02 xxxx xxx1 xxxx xxxx xxx0 xxxx
Conversion
Halogen to LED Rear Turn trucks.com/forums/1517743-complete-how-to-halogen-to-led-heads-and-tails.html jmeo
BCM 726-27-02 xxxx xxxx x*xx
Rear bulb turn outage config: 1=outage, 0=no outage
Signal Conversion
DESCRIPTION PENDING BCM 726-28-01 x*xx xxxx xxxx
Rear LED turn outage cfg: 1=outage 0=no outage
04=C-Max, 06=Mustang, 08=Escape, 09=Edge, 24=Mondeo, 0B=Explorer, 20=Fiesta,
Bluetooth Pairing Name APIM 7D0-04-01 xxxx xxxx **xx Livinitup
1B=MKC, 2E=Continental, 1C=MKX, 1E=Navigator, 0C=Expedition. ** The above only works
Average Speed Display IPC 720-01-01 2F0F 1064 724Dxxxx x4xx xxxx
Adds "Average Speed" menu item to the Trip/Fuel menu. Livinitup
Massage Seats SCMG/SCMH Multiple See link Link to F150 Spreadsheet for all values Livinitup
8=4 Flashes OUC False 9=4 Flashes OUC True
Turn Signal Flash Count SCCM 724-01-01 xxxx x6xx xx xxxx x*xx xx Livinitup
Switch Steering Wheel A=5 Flashes OUC False B=5 Flashes OUC True
functions from right bank to left bank. Note: This is only for the Up,Down,Right,Left/Center
SCCM 724-01-01 xxxx 0xxx xx xxxx 8xxx xx Livinitup
Buttons LED Lighting (Door
Ambient buttons. Not
8=Amber the lower
(Lincoln), set for
9=Teal cruise control,
(Lincoln), A=Red voice commands,
(Lincoln), B=Blueetc. ClusterC=Green
(Lincoln), Crossover Cfg:
(Lincoln),
BCM 726-31-01 x*xx xxxx xx flsdiver
Ajar)
Ambient LED Lighting D=Lilac (Lincoln),
8=Amber E=Unknown,
(Lincoln), F=Unknown.
9=Teal (Lincoln), A=Red Note: SyncB=Blue
(Lincoln), 3: Use Lincoln Splash
(Lincoln), Screen
C=Green Brand
(Lincoln),
BCM 726-31-02 xxxx x*xx xxbutton flsdiver
(Entry) D=Lilacwith a dualE=Unknown,
(Lincoln), function hazard and HDC enable
F=Unknown. button
Note: Sync partLincoln
3: Use #: HC3Z-13D730-CA. For
Splash Screen Brand
Add Hill Descent Control ABS 760-03-01 x1xx xx x3xx xx more information
0=TBC see&the
Gain disabled following
TPMS thread:
Specified value disabled Mooch91
Add TPMS "Specified" to https://www.ford-trucks.com/forums/1503198-forscan-adding-hill-descent-control-to-
IPC 720-04-01 xx*x xxxx xxxx
4=TBC Gain enabled & TPMS Specified value disabled Livinitup
display
Disable Traction Control IPC 720-01-01 8=TBC
xx2x xxxx xxxx Gain disabled
AdvanceTrac Disabled & TPMS Specified value enabled
Enter NAV Destination and keep their eyes on the road. Be smart and be safe. This feature disables automatic 911 Livinitup
viewing texts while vehicle APIM 7D0-02-01 5753 xxxx xxxx
calling if in an accident. Livinitup
Disable
is Door Chime when
in motion iPC 720-01-02 xx1x xxxx xxxx xx0x xxxx xxxx
Disables
This doorchime
disables chimewhen
whenkey door is open
in theand ignition
iginition andon.
ignition is off. Subtract 8 from the value neonovulator
Door Ajar
Disable Key In Ignition
iPC 720-02-01 xx*x xxxx xxxx
in the * position. For example, if C then change to 4. This feature is dependent upon the neonovulator
Chime
Disable Illuminated BCM 726-32-01 Disable
xxxx x1xx xxxx
Turns offDoor Chime
parking andwhen
cargoDoor Ajar
lights feature.
when doorThat must be enabled first for this to work.
is opened.
R1xterGonz0
Entry/Exit - Dark Car Mode BCM 726-58-02 xxxx xxxx x1xx
Silent mode. Waiting for better description
Remote Start
BCM 726-22-02 xxx* xxxx xxxx
Substitute * with one of the following: 0=disabled, 1=enabled Livinitup
Enable/Disable
APIM 7D0-01-01 Adds climate screen to Sync v3 and above XL and XLT trims. Note: Fan speed control does
xxxx xxx3 xxxx
Add Climate Screen for not work, remains on the analog dial, Does not add dual climate capabilities, Temp control
Uzumati
XL/XLT APIM 7D0-01-02 xxxx x2xx xxxx does not work, remains on the analog dial. What does work- On/Off, AC & Recirculate
On/Off,seconds
0=15 Vent Control - foot,
delay dash, windshield,
turning on headlamps Some when
voice commands
dark, 1=2 seconds delay
Ambient Light Sensor Speed BCM 726-26-01 xxx* xxxx xxxx This
turning on will
update headlamps
correct thewhen dark to read accurately for the larger tire size. It will
speedometer Livinitup
Speedometer Calibration for KubotaOrange
BCM 726-12-01 0163 0ACC xxxx however, also set a check engine light (CEL) because of the difference from factory settings.
37 inchAuto-Regen
Enable Tires Default is checkbox selected. Disabling will cause regen message to prompt user to perform 76
IPC 720-07-02 xxxx xxx4 xxxx xxxx xxxC xxxx There appears to be no other negative effects other than the CEL. screwy
Checkbox regen. Additional description pending further user experience.
 Module Character
Acronym Module Description s Utility Web Address
ABS Anti-Lock Brake System Module 760 Decimal to Hex Converter: http://www.asciitohex.com/
ACM Audio Front Control Module 727 Math for conversion http://www.permadi.com/tutorial/numDecToHex/
APIM Sync Module 7D0 As Built data by individual VIN Motorcraft Service AsBuilt Data
BCM Body Control Module 726 Owner's manuals and other delivery https://www.motorcraftservice.com/ownerinformation
CCM Cruise Control Module 764 Link to F150 FORScan spreadsheet F150 Features & Modules Mapping
DACMC Digitial Audio Control Module C FORScan download page http://www.forscan.org/download.html
DCSM Front Seat Climate Control Module FORScan Forum FORScan Forum
DDM Driver Door Module 740 F150 Forum https://www.f150forum.com/f2/forscan-applications-346877/
DSP Audio Digital Signal Processing Module 783 Ford Mustang Forum http://www.mustang6g.com/forums/showthread.php?t=61773
FCIM Front Control Interface Module 7A7 Ford Raptor Forum http://www.fordraptorforum.com/f260/forscan-changes-tweak-your-truck-52149/
GWM Gateway Module A 716 Powerstroke Army Forum http://powerstrokearmy.com/forums/showthread.php?t=74531&showall=1
HSWM Heated Steering Wheel Module 714 F150 Ecoboost Forum http://www.f150ecoboost.net/forum/6-f150-ecoboost-chat/18362-forscan-ability-change-bcm-build-data-activate.html
HUD Heads Up Display Module 7B2 Fusion Forum http://www.2gfusions.net/showthread.php?tid=4573
IPC Instrument Panel Cluster 720 Sync 3.0 Update with NAV https://1drv.ms/u/s!AgM4_H5aFPr20m9NrR67iLLwlRIP
IPMA Image Processing Module A 706 Sync 3.0 Update without NAV https://www.transfernow.net/93c957x2pbbt
IPMB Image Processing Module B 7B1
OCS Occupant Classification System Module
PAM Parking Assist Control Module 736
PCM Powertrain Control Module 7E0
PDM Passenger Door Module 741
PSCM Power Steering Control Module
RBM Running Board Control Module 766
RTM Radio Transceiver Module 751
SCCM Steering Column Control Module 724
SCMG Driver Multi-Contour Seat Module 712
SCMH Passenger Multi-Contour Seat Module 713
SODL Side Obstacle Detection Control Module 7C4
SODR Side Obstacle Detection Control Module 7C6
TBM Trailer Brake Control Module 757
TCM Transmission Control Module 7E1
TCCM Transfer Case Control Module 761
TRM Trailer Module 791
Three steps for downloading, installing and activating the FORScan software:
1. Registermode
Bootcamp on theorForum
Parallels. Copy the Hardware ID (found in FORScan software under the http://www.forscan.org/forum/ucp.php?mode=register
steering wheel with a question mark icon). http://www.forscan.org/download.html
3. Generate the Extended License (free) using the previously copied Hardware ID http://forscan.org/forum/extlic.php
At this point you are registered on the forum and your copy of the FORScan software is
activated.

Connecting FORScanThere
connector. to theare
truck:
many connectors available and some work properly and others don't.
The following is proven to work in all cases. Search "OBDLink MX Bluetooth" on Amazon. http://amzn.to/2kWQguk
Compatible USB OBDII adapter with manual switch http://amzn.to/2ziwvPU
Another compatible USB OBDII adapter with manual switch http://amzn.to/2gOVfsy
and FORScan will begin scanning all available modules. Wait until complete and you're ready
to go.

FORScan Training:
Extremely helpful tutorial which provides real-word examples as to how to use the software https://docs.google.com/document/d/1-
and make updates to modules. Thanks to Livinitup. 8dKaS_Spu4Zw4hV_CrKC4tLoP9G8yejqegF1wxIqxY/edit

Backing Up Modules
into Beforeclick
each module, Modifications:
"save all" at the bottom and name it something like BCM-original, IPC-
original, etc."

Disclaimer:truck and may have negative or unintended consequences. If you choose to make any
modifications to your truck you do so at your own risk