Profile cut tool start

% O2202 = Output number

O2202(R-2=SHN=ROU=2TH=Z78.0) (R-2=SHN=ROU=2TH=Z78.0) = File name
--BLANK--
(|@33-R2.5 FF/C|H21) Tool name
(|@100 F/C|H23) H value,
G21 G21 = Fixed value
N10(@33-R2.5 FF/C|TOOL - 21|DIA. OFF. - 21|LEN. - 21|TOOL DIA. - 33.) N10 = sequence number
T21M6 - Sequence number progression (N10->N20-
T2 >N30…)
M01 Tool information
G0G17G40G49G80G90 T21 M6 = ATC
G0G90G54X-354.858Y0.S1200M3 T2 = Next tool
G43H21Z50. M01 = Fixed value
M8 G0G17G40G49G80G90 = Fixed value
Z4. G0G90G54 = Fixed value
X-354.858Y0. = Tool start point
S1200M3 = Spindle
G43H21Z50. = H value
M8 = Coolant on
 Profile cut tool change
G0Z50. Fixed vlaue
M9
M5
G91G28Z0.
M01
N20 (|@100 F/C|TOOL - 2|DIA. OFF. - 2|LEN. - 2|TOOL DIA. - 12.) N20 = sequence number
T2M6 - Sequence number progression (N10->N20-
T3 >N30…)
M01 Tool information
G0G17G40G49G80G90 T2 M6 = ATC
G0G90G54X196.Y12.S4500M3 T3 = Next tool
G43H2Z50.M8 M01 = Fixed value
Z3. G0G17G40G49G80G90 = Fixed value
G0G90G54 = Fixed value
X196.Y12 = Tool start point
S4500M3 = Spindle
G43H2Z50. = H value
M8 = Coolant on
 Profile cut Tool Finish

G0Z50.
M9
M5 Fixed value

G91G28Z0.
G28Y0.
M30
%
 Drill start
% O1821 = Fixed value
O1821(1821=1TH) (1821=1TH) = File name

(|@5.9 D/R|H18) Tool name

(|@6 RIMER|H19) H value,
(|@6.9 D/R|H14) G21 = Fixed value
(|M8X1.25 TAP|H15) N10 = sequence number
G21 - Sequence number progression (N10->N20-
N10(@5.9 D/R|TOOL - 18|DIA. OFF. - 18|LEN. - 18|TOOL DIA. - 5.9.) >N30…)
T18M6 Tool information
T19 T18 M6 = ATC
M01 T19 = Next tool
G0G17G40G49G80G90 M01 = Fixed value
G0G90G54X130.Y-15.S1800M3 G0G17G40G49G80G90 = Fixed value
G43H18Z50.M8 G0G90G54 = Fixed value
G98G83Z-20.R3.Q1.F300. X130.58Y-15.. = Tool start point
X160.Y-45. S1800M3 = Spindle
G43H18Z50. = H value
M8 = Coolant on
 Drill tool change
G80 G0 Z50. Fixed vlaue
M9
M5
G91G28Z0.
M01
N60(@6 RIMER|TOOL - 19|DIA. OFF. - 19|LEN. - 19|TOOL DIA. - 6.) N60 = sequence number
T19M6 - Sequence number progression (N10->N20-
T14 >N30…)
M01 Tool information
G0G17G40G49G80G90 T19 M6 = ATC
G0G90G54X130.Y-15.S1000M3 T14 = Next tool
G43H19Z50.M8 M01 = Fixed value
G98G86Z-17.R3.F100. G0G17G40G49G80G90 = Fixed value
X160.Y-45.. G0G90G54 = Fixed value
X130.Y15. = Tool start point
S1000M3 = Spindle
G43H19Z50. = H value
M8 = Coolant on
 Drill Finish

G80 G0 Z50.
M9
M5 Fixed value
Z50 = Clearance Z
G91G28Z0.
G28Y0.
M30
%