Scribd Logo
Upload

Welcome to Scribd!

  • 16 views

    Question Paper Winter 2022

    Uploaded by

    sabaleom54

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Question Paper Winter 2022

    Uploaded by

    sabaleom54
    16 views5 pages

    Original Title

    22531 Question Paper Winter 2022

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    16 views5 pages

    Question Paper Winter 2022

    Uploaded by

    sabaleom54

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 5

    22531

    12223
    3 Hours / 70 Marks Seat No.

    Instructions – (1) All Questions are Compulsory.


    (2) Answer each next main Question on a new page.
    (3) Illustrate your answers with neat sketches wherever
    necessary.
    (4) Figures to the right indicate full marks.
    (5) Assume suitable data, if necessary.
    (6) Use of Non-programmable Electronic Pocket
    Calculator is permissible.
    (7) Mobile Phone, Pager and any other Electronic
    Communication devices are not permissible in
    Examination Hall.
    Marks

    1. Attempt any FIVE of the following: 10


    a) Define control system and give any two practical examples.
    b) Define
    i) Transient response
    ii) Steady state response
    c) State the classification of control actions.
    d) Draw the symbols of NO and NC contacts used in PLC.
    e) List Timer and counter instruction of PLC.
    f) Define
    i) Poles
    ii) Transfer function
    g) Draw the ladder logic diagram
    i) NAND Gate
    ii) EX-OR Gate P.T.O.
    22531 [2]
    Marks
    2. Attempt any THREE of the following: 12
    a) For the given transfer function
    10 (S + 3)
    T.F. = Find
    (S + 2) (S + 1) (S + 4)
    i) Pole’s
    ii) Zero’s
    iii) Characteristics equation
    iv) Plot Pole’s and Zero’s in S-plain.
    b) State the need of PLC in automation.
    c) Draw the ladder logic diagram
    i) Half Adder
    ii) Half Substractor
    d) Explain scanning cycle of PLC.

    3. Attempt any THREE of the following: 12


    a) Derive the transfer function of following circuit.
    Refer Fig. No. 1.

    Fig. No. 1.
    b) Describe ON-OFF control action with equation and response
    curve.
    c) Sketch the block diagram of PLC.
    d) Explain the Sourcing and Sinking concept in D.C. Input
    module.
    22531 [3]
    Marks
    4. Attempt any THREE of the following: 12
    a) Explain Propertional Integral (PI) controller with O/P response
    curve.
    b) Distinguish between fixed and modular PLC. (any four points)
    c) Sketch the block diagram of process control system and explain
    the function of each block.
    d) Draw block diagram of AC discrete input module of PLC.
    e) Explain memory organization of PLC.

    5. Attempt any TWO of the following: 12


    a) For the given differential equation
    d 2 y(t) dy(t)
    2 + 4 dt + 8y(t) = 8x(t)
    dt
    where y(t) is O/P and x(t) is I/P
    Find, All Time Response Specification.
    (ξ, Tr , Tp , Td , Ts , % Mp )

    b) Find out transfer function by using block diagram reduction


    technique. Refer Fig. No. 2.
    C(S)
    TF = R(S) = ?

    Fig. No. 2.

    c) Calcualte range of K for the given unity feedback system to be


    stable with G(S).
    K
    G(S) =
    S(S + 2) (S + 4) (S + 8) P.T.O.
    22531 [4]
    Marks
    6. Attempt any TWO of the following: 12
    a) Define transfer function and derive the derivation of transfer
    function of closed loop control system.
    b) A unity feedback system has
    10 (S + 1)
    G(S) =
    S2(S + 2) (S + 10)
    Find.
    i) Type of system
    ii) Error coefficients kp , kv , ka.
    2
    iii) Steady state error ess , for input r(t) = 1 + 4t + t2 .
    c) Draw the ladder diagram for the following circuits.
    Refer Fig. No. 3, 4 and 5.
    i)

    Fig. No. 3.
    ii)

    Fig. No. 4.
    22531 [5]
    Marks
    iii)

    Fig. No. 5.

    You might also like