Scribd
Upload
13 views4 pages

What Does Storage Server Mean

Uploaded by

sheikh rahil
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
13 views4 pages

What Does Storage Server Mean

Uploaded by

sheikh rahil
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

What Does Storage Server Mean?

A storage server is a type of server that is used to store, access, secure


and manage digital data, files and services. It is a purpose built server
used for storing and accessing small to large amount of data over a
shared network or through the Internet.

A storage server may also be called a file server.D

Storage types fall into three main categories....


 Direct attached storage – DAS
 Storage area network – SAN
 Network attached storage – NAS
Direct attached storage has progressed through various technologies; PATA,
SATA, SCSI, SAS, all using different cable connectors. However most higher end
shared storage is accessed over the network using a NAS, or SAN configurations
like Fibre Channel, iSCSI or AoE (ATA over Ethernet).

DAS
These disks are connected directly (locally) and used in both servers and
workstations. Directly attached storage connects multiple disks in arrays, or
single disks of the following types:

PATA: Parallel ATA, or ATAPI. 150MBps. (Megabytes Per Second)


These disks use IDE connectors to connect one or two drives on a cable, usually
DVD drives and hard disk drives. There are still some in use, but PATA is old
technology now.

SATA: Serial ATA. 6Gbps currently for SATA III (That's 600MBps)
These disks have their own fast channel on the controller and use much narrower
cables than PATA.
When using these drives in a server or SAN make sure they have a high MTBF
rating, (mean time between failures) as workstation drives fail more quickly. The
SSD (Solid State Disk) variety of SATA can achieve higher read/write results than
standard SATA disks; 1,100 MBps reads and close to 700 MBps writes. They have
no moving parts as they only contain chips.

Ultra320: SCSI drives. 320MBps


These SCSI (Small Computer System Interface) drives were the standard for
servers in the past. The shared bus connectors could hold up to 14 disks but
contention would increase the more disks were added. The maximum disk size is
300GB.

SAS: Serial Attached SCSI. 3GBps/8gbps currently.


As IDE was replaced by SATA for workstations, similarly SAS has replaced SCSI
for servers. SAS drives are dual-ported and therefore faster than SATA but SAS
drives cannot be as large as SATA. Currently a standard 3.5” SAS runs at 15,000
RPM, and a 2.5” runs at 10,000RPM but with smaller storage. However the
advantage of smaller disks is that more can be squeezed in giving an over all
increase in capacity and access speed. A NLSAS (Near Line SAS) combines a SAS
interface with a SATA drive. These can be up to 2TB in size currently. They
provide larger volume but with the lower performance of an SATA drive at
7500RPM.

NAS
A NAS has multiple disks usually in a RAID array, and appears on the network as
a single node of shared storage. NAS storage does not appear to your server or
computer as a disk drive, rather as a network location which can be added as a
mapped drive. They are popular because they are much cheaper than SANs and
allow the creation of user access permissions, and certain software can be run
from them. They are often used to back up servers or to provide access to
shared files to many computers.

They use shared file system protocols like SMB/CIFS, NFS, AFS and GFS. These
protocols allow multiple users to access the same file at the same time, however
this overhead software does make transmission slightly slower than SANs.

SAN
Unlike a NAS, a SAN presents a drive for the server to connect to, which appears
in disk management like a normal drive would. SANs incorporate multiple
network devices on a separate self-contained network, which appear as one
drive, which can be divided up. These drives are then available to multiple
servers and computers. They often use higher end switches to create a VLAN,
which joins the two networks together and provides security. They use SAS or
SATA in multiple RAID arrays connected together. There are two types of SAN;
iSCSI and Fibre Channel (FC), both use SCSI commands, except that FC packages
SCSI commands into Fibre Channel frames, and iSCSI uses Internet Protocol.

iSCSI SANs. 1Gbps/10Gbps currently


iSCSI is the first protocol that uses native SCSI commands end-to-end over IP,
(although fibre Channel can be made to do this.) It's speed it limited by the
speed of the LAN as it uses ordinary network cards. iSCSI SANs can be bought
ready-made but can also be put together with standard hardware.

The iSCSI device is referred to as the 'target' and any computer or server can be
used as an 'initiator' as long as it has initiator software installed. (This includes
Apple Mac). The initiator scans the target looking for a LUN (Logical Unit Number)
Each Logical Unit can be made up of many configurations, for example a whole
RAID set, or a group of partitions or disks, but is seen by the LUN as one drive.
There are two versions of Microsoft iSCSI Initiator installed on a Microsoft server;
one version is to allow booting from the SAN when the OS is installed on it, the
other is for use as normal storage.

Fibre Channel SANs. 2Gbps/20Gbps currently


Fibre channel is actually older than iSCSI and uses dedicated hardware instead of
just NICs and switches; it uses special controllers called HBAs (Host Bus Adaptor)
on the client computers, and special fibre channel cables and switches to
interconnect the components. Traditionally the cables were fibre optic, but
twisted pair and coaxial copper cables also exist. FC is more expensive but it is
reliable and secure, which is why it is widely used. An HBA card is needed for
each server, which connects to a port on the Fibre Channel switch. The switch
usually has four ports for redundancy and speed, in case one pathway fails,
another takes over. Once LUNs are created on the Target, they can be zoned and
masked to ensure that they are only accessible to the proper servers or
applications. The maximum length of Fibre Optic cable depends on the quality of
the cable, for example 50/125 multimode fiber can reach up to 500 meters.

I am writing to express my strong interest in contributing to your data collection


activities in the field. With a background in customer support, I am enthusiastic
about the prospect of ensuring the success and accuracy of your projects.
I would welcome the opportunity to discuss how my skills align with your team's
needs and contribute to the effective execution of data collection initiatives.
Thank you for considering my interest.
Best regards,
I am writing to express my keen interest in the Sports Statistician position within
your organization. As someone deeply passionate about sports and possessing a
strong analytical background, I am excited about the opportunity to contribute to
data-driven insights that enhance team performance.
My experience in [mention relevant skills or experiences] has equipped me with
the tools to extract meaningful patterns from sports data, and I am eager to
bring this expertise to [Company/Organization Name]. I am particularly drawn to
the role due to its dynamic nature, continuous learning opportunities, and the
chance to influence strategic decisions within the sports industry.
I look forward to the possibility of discussing how my skills align with the
requirements of the position and how I can contribute to the success of your
team.

You might also like