1.

To prevent leakage in dynamic seal:

a. Gaskets
b. Seals
c. Felts
d. Packings *
2. Type of gear cut inside a cylinder or ring:
a. Rack gear
b. Ring gear
c. Miter gear
d. Internal gear *
3. What heat treatment processes can cast steel materials for high chrome, high
manganese, ect. Type steel be subjected for the purpose of machining process?
a. Annealing *
b. Tempering
c. Normalizing
d. Quenching
4. Galvanized steel plate is a plate coated with:
a. Aluminium
b. Tin
c. Zinc *
d. Manganese
5. Major component of bronze casting-
a. Copper *
b. Manganese
c. Zinc
d. Lead
6. Split pulley or pulley made of separate section bolted together at the rim, the
maximum speed should be limited to about _____% of the maximum speed of solid
pulley.
a. 65 to 75 %
b. 45 to 50 %
c. 55 to 60 %*
d. 80 to 90 %
7. Heating of the material to a temperature above the critical temperature and then
cooling slowly usually in the furnace the hardness and improve the mechanically is
called:
a. Annealing *
b. Tempering
c. Normalizing
d. Quenching
8. A hydrostatic bearing is one which:
a. The lube oil is supplied under pressure*
b. Lube oil is not pressurized
c. There is no lube oil
d. Bearing is lightly loaded
9. The angle, at the base of the cylinder of an involute gear, that the tooth makes with
the gear axis:
a. Base helix angle *
b. Pressure angle
c. Arc of recess
d. Arc of approach
10. Copper and most of its alloys can be hardened by:
a. Patenting
b. Cold working*
c. Case hardening
d. Soaking
11. Which of the following is not a structural class of steel?
a. Low carbon steel
b. Stainless steel
c. Medium carbon steel
d. Tool and die steel*
12. A material that should be avoided in constructing wood pattern:
a. Sap wood*
b. Kiln dried wood
c. Heart wood
d. Core portion of wood
13. Which the property of a material which resists forces acting to pull the material
part?
a. Shear strength
b. Tensile strength*
c. Torsional strength
d. Compressive strength
14. The reciprocal of diametral pitch equivalent to the ratio of pitch diameter to the
number of teeth:
a. Lead
b. Clearance
c. Module*
d. Involute
15. The first derivative will respect to velocity of kinetic energy is:
a. Power
b. Acceleration
 c. Momentum*
d. None of the above
16. What type of gears that can transmit power at an angle?
a. Helical gear
b. Worm gear
c. Bevel gear*
d. Herringbone gear
17. A liquid metal:
a. Mercury*
b. Lead
c. Zinc
d. Aluminium
18. Device use to measure accurately speed:
a. Speedometer
b. Dial indicator
c. Tachometer*
d. Dial gauge
19. When two elastic bodies collide, which of the following law can be used to solve for
the resulting velocity?
a. Dalton’s Law
b. Avogadro
c. Conservation of energy
d. Conversation of momentum and conversation of energy*
20. A system of force in space is in equilibrium. If two equal and opposite collinear forces
are added. Which of the following if any is any is true?
a. Equilibrium is destroyed
b. Equilibrium is maintained*
c. None of these is true
d. An unbalanced of moment exist
21. Metal that assists lubrication or lubricant itself:
a. Zinc
b. Babbitt*
c. Antimony
d. Lead
22. A mechanism which usually do the indexing in machine tool:
a. Universal chuck
b. Slotter
c. Dividing head*
d. Indexing
23. The smallest area at the point of rapture specimen divided by the original area is
called:
 a. Percentage elongation*
b. Izod test
c. Charpy test
d. Percentage reduction of area
24. The product if the resultant of all forces acting on the body and the time that the
resultant acts:
a. Angular impulse
b. Angular momentum
c. Linear impulse*
d. Linear momentum
25. All area associated with the grade of steel except:
a. SAE 43xx
b. SAE 13xx
c. SAE 10xx
d. SAE 74xx*
26. A property of material which relates the lateral strain to the longitudinal strain:
a. Stress
b. Strain
c. Poisson’s ratio*
d. Strength
27. Hypoid gear is a special type of gear like:
a. Worm gear
b. Spur gear
c. Herringbone gear
d. Bevel gear*
28. Consider a minimum safe center distance of sprockets should be ____ pitches. Very
long center distance cause catenary tension in the chain.
a. 70
b. 80*
c. 60
d. 50
29. Cold working of steel plates makes the metal:
a. Tougher
b. More ductile
c. Harder*
d. More malleable
30. Deal only with motion of bodies without reference to the forces that cause them:
a. Dynamics
b. Kinetics
c. Statics
d. Kinematics*
31. The property that characterizes a material ability to be drawn into a wire:
a. Ductility*
b. Thermal conductivity
c. Tensile strength
d. Endurance limit
32. The three moment equation may be used to analyze:
a. Tapered column
b. Continuous beam*
c. Composite beam
d. Axially end loaded beam
33. Non-ferrous filter metal is melted into grooves or is filet on the mother metal; the
base metal is not melted. This commonly use for joining iron base machine parts or
in repair works of some materials. It is called:
a. Spot welding
b. Braze welding*
c. Brazing
d. Gas welding
34. It is advised that in rubber belts application/mounting, it should have an initial
tension of ___ inch/ply.
a. 18 to 24
b. 15 to 20*
c. 12 to 15
d. 10
35. Normal stress relieving for cast steel:
a. 200 to 350 oF
b. 400 to 500 oF
c. 300 to 400 oF
d. 450 to 550 oF**
36. Most effective allowing element for reducing brittleness of steel at very low
temperature:
a. Manganese
b. Molybdenum
c. Silicon
d. Nickel*
37. Statement that a given body is in static equilibrium means that the body cannot:
a. Have any type of motion*
b. Be acted upon by more than one force
c. Undergo any displacement
d. Have any acceleration
38. Ordinary steel begins to lose strength and elastically significantly at about _____ oF
a. 900-1000 oF
 b. 800 -900 oF
c. 750 -850 oF
d. 600-700 oF*
39. Clearance to a new boiler installation to the existing or cold plant building shoulf
follow a minimum clearance of ____ between top of the boiler proper and the ceiling
as stated in the PSME Code.
a. 2000 mm(max)
b. 1000 mm(max)
c. 2130 mm(max)*
d. 2150 mm (max)
40. For high corrosion resistance stainless steel, what minimum chromium content is
required?
a. 8%*
b. 4.3%
c. 1,1 %
d. 5.8 %
41. Name the type of chuck commonly used for holding workplaces in a lathe operation?
Example 3-jaw universal chuck, 4- jaw independent chuck.
a. Magnetic jaw chuck
b. 2 –jaw independent chuck’
c. 8-jaw universal
d. Combination*
42. What type of gear used for high speed operation?
a. Helical*
b. Spur
c. Bevel
d. Worm
43. In a pair of gears ____ is the plane perpendicular to the axial plane surface.
a. Pitch
b. Pitch plane*
c. Pitch circle
d. Pitch point
44. A machinery operation whereby done with the work accurately fastened has a
reciprocating (forward and backward) motion and the tool head is stationary.
a. Shaping
b. Planning*
c. Turning
d. Reaming
45. The usual ratio of water to soluble oil is used as cutting fluid:
a. 50 % water to 50 % oil
b. 2 water to oil
 c. 3 water to 1 oil
d. 4 to 80 water to 1 oil*
46. It considered semi-solid lubricant:
a. All of these
b. Lube oil
c. Graphite
d. Grease*
47. The purpose of these part in application are to have better bearings to seal the guard
against marring, etc.
a. Bearing journal
b. Metallic seal
c. Washer*
d. Shaft seal
48. They yield strength of a regular yellow brass (65 to 70 % Cu, 30 to 35 % Zn) can be
increased/improved by:
a. Cold working*
b. Tempering
c. Chill casting
d. Heat treatment
49. Machine tool used for laying straight lines on metal surface made of sharp tool steel
is called:
a. Plain scriber*
b. A trammel
c. Herphrodite calliper
d. Divider
50. It is the difference of addendum and dedendum which is equivalent to the whole
depth less working depth
a. Fillet radius
b. Fillet radius
c. Clearance*
d. Backlash
51. A lathe machine treading mechanism:
a. Reverse gear and lever
b. Spindle gear*
c. All of these
 d. Change stud gear
52. Separates forces which can be so combined are called:
a. Component*
b. Concurrent forces
c. Couple
d. Non-concurrent forces
53. What property of matter which causes it to resist any change in its motion or state of
rest:
a. Brake
b. Friction
c. Inertia*
d. Impulse
54. Which of the following is not use to resemble the shape of tool bit?
a. Round nose
b. Center cut*
c. Square nose
d. Thread cutting
55. For moderate speed of mating gears, the ideal ratio of contact is:
a. 1.25-4*
b. 1.2-1.45
c. 1.0-1.3
d. 1.35-1.45
56. Ratio of unit lateral deformation to unit longitudinal deformation:
a. Poisson’s ratio*
b. Strain
c. Elongation
d. Modulus of elasticity
57. A lathe with multiple cutting stations:
a. Turret lathe*
b. Lathe
c. Shaper
d. None of the above
58. Nominal diameter of the bolts is the:
a. Major diameter*
b. Minor diameter
c. Pitch diameter
d. Base diameter
59. Length of contact between two mating parts in a screw and nut threads measured
axially is called:
a. Arc of contact
b. Dept of engagement
c. Length of engagement*
d. Axis of contact
60. If the velocity of a mass is the time during which motion takes place is called:
a. Deceleration
b. Uniform motion*
c. Acceleration
d. None of these
61. The property of material that relates the lateral strain to longitudinal strain:
a. Stress
b. Strain
c. Poisson’s ratio*
d. Endurance limit
62. In absolute teeth the pressure angle is often defined as the angle between the line of
action and the line of tangent to the pitch circle. It is also termed as:
a. Helix angle
b. Angle of recess
c. Angle of obliquitty*
d. Arc of action
63. The angle made by the helix of the thread (in a straight thread ) at the pitch diameter
with a plane perpendicular to the axis is called:
a. Lead angle*
b. Truncation
c. Lead
 d. Angle of thread
64. The cast iron flywheels are commonly designed with a factor of safety of _____
a. 14 to 15
b. 10 to 13*
c. 8 to 9
d. 6 to 12
65. A pair of equal and opposite (not collinear) forces that to causes a rotation of a body.
a. Couple*
b. Centroids
c. Equilibrium
d. Vector
66. The ratio of the pitch diameter in inches to the number of teeth.
a. Pitch circle
b. English module*
c. Module
d. Pitch diameter
67. When the motion is diminished/decreasing instead of increasing instead of
increasing is called:
a. Deceleration
b. Uniform negative impulse
c. Retarded motion*
d. All of these
68. ___________ is a unit of energy
a. Ft-lb*
b. Hp
c. Btu/hr
d. Watt
69. The product of the mass and the velocity of the center of gravity of the body is
called:
a. Linear momentum*
b. Angular impulse
c. Linear impulse
 d. Angular momentum
70. Could be defined as simply push or pull.
a. Power
b. Inertia
c. Work
d. Force*
71. Opposite directional forces equal in magnitude and parallel is called ______
a. Non coplanar
b. Centro
c. Couple*
d. Coplanar
72. Quantities such as time, volume and density are completely specified when their
magnitude is known is also called ___________
a. Couple
b. Resultants
c. Components
d. Scalar*
73. ______ is the product of the resultant of all forces acting on a body and the time.
a. Linear momentum
b. Linear impulse*
c. Angular momentum
d. All of these
74. The separate forces which can be so combined are called:
a. Concurrent forces
b. Non concurrent forces
c. Couple
d. Component forces*
75. Continuous stretching under load even if the stress is less than the yield point.
a. Plasticity
b. Elasticity
c. Creep*
d. Ductility
76. The most known lubricants being utilized in whatever category of load and speed are
oil, air, grease and dry lubricants like:
a. Bronze
b. Lead
c. Silicon
d. Graphite*
77. A coupling that allows axial flexibility/movement in the operation. Made of alternate
bolting of steel, leather, fabric and/or plastic material into two flanges.
a. Flexible disk coupling*
b. Flexible toroidal spring coupling
c. Flexible Oldham coupling
d. Elastic material bounded coupling
78. It consists of two cranks, stationary piece called the line of centers and the
connecting rod is a:
a. Five-bar linkage
b. Four crank braces
c. Three crank linkage
d. Four bar linkage*
79. Used to change rotary motion to reciprocating motion _________
a. Rack gears*
b. Hypoid gears
c. Helical gears
d. Herringbone gears
80. The effective face with of a helical gear divided by gear axial pitch.
a. Approach ratio*
b. Arc of action
c. Arc of recess
d. Face overlap
81. Pitch diameter less the diameter of the roller chain is equal to:
a. Top land
b. Bottom diameter*
c. Addendum
 d. Inside diameter
82. Generally applied on speed reducer due to large speed ratio.
a. Bevel gears
b. Helical gears
c. Worm gears*
d. Hypoid gears
83. If the shaft size is specified to a load. When the load was removed, the strain
disappeared. From the structural changes, which of the following can be considered
about this material?
a. It has high modulus of elasticity
b. It does not follow hooke’s law
c. It is plastic
d. It is elastic*
84. Helix angle in the range of _____ degrees is recommended for wide-face helical
gears.
a. Less than 15*
b. Less than 20
c. 20 to 35
d. 20 to 22
85. Difference between maximum materials limits of mating parts. Or it is a minimum
clearance or maximum interference between parts.
a. Tolerance
b. Fits
c. Variance
d. Allowance*
86. The concave portion of the tooth profile where it joints the bottom of the tooth.
a. Root circle
b. Fillet radius*
c. Fillet curves
d. Fillet
87. The changes in shape or geometry of the body due to action of a force on it is called
deformation or __________
 a. Shear stress
b. Stresses
c. Compressive stress
d. Strains*
88. For eventually and uniform wear on each meshing gear tooth, the ideal design
practice is to consider a ___________
a. Wear resistance alloy addition to tooth gears
b. Heat treatment of the gear
c. Hardening of each tooth
d. Hunting tooth addition*
89. The reciprocal of a diametral pitch or the ratio of the pitch diameter to the no. Of
teeth.
a. Lead
b. Module*
c. Involute
d. Clearance
90. Ability to resists deformation under stress.
a. Plasticity
b. All of these
c. Stiffness*
d. Toughness
91. The angle include between the sides of the thread measured in an axial plane in a
screw thread.
a. Angle of thread*
b. Angle between thread or 40o
c. Helix angle thread
d. Half angle thread or 20 o
92. Chromium steel standard designation, SAE______
a. 92xx
b. 5xxx*
c. 3xxx
d. 11xx
93. Alloys that improves strength of steel a high temperature application.
a. Aluminium
b. Manganese
c. Silicon
d. Chromium*
94. The different of the shear equation is the
a. Deflection of the beam
b. Compressive strength of the beam
c. Tensile strength of the beam
d. Load on the beam*
95. Length of contact between two mating parts in screw and nut threads measured
axially is termed__________
a. Length of engagement*
b. Axis of contact
c. Arc of contact
d. Depth of engagement
96. The sum of their addendums and dedendums:
a. Whole depth*
b. Full depth
c. Width depth
d. Working depth
97. Stress that are independent of loads is called__________
a. Working stress
b. Residual stress*
c. Simple stress
d. Combined stress
98. Material having a high electrical resistance and should not be used as conductor of
electrical current.
a. Nickel*
b. Aluminium oxide
c. Silicon base alloys
d. Iron oxide
99. Drilling machine cannot do:
a. Reaming
b. Spot facing
c. Tapping*
d. Broaching
100. Material changes in foundry melting operation are composed of:
a. Limestone, foundry coke and silica sand*
b. Iron ore, quarts and charcoal
c. Steel scrap, alloys and charcoal/foundry coke
d. Scrap wood, alloys and limestone