L99DZ100 – Eval - GUI

v1.0
Body Smart Power BU
Door Zone
L99DZ100G(P): DZ2015 Demo Board 22

Case 1: uC Section – SPC560B54L3

Case 2: FTDI-USB Interface

Case 3: Chipboard Interface

Case 4: Power Supply Section

Case 5: Output Section

ST Confidential
 uC Section – SPC560B54L3
Door Zone
3

The chosen unit is the SPC560B54L3 Bolero,

32 bit uC belonging to the SPC5 family.
In the showed schematic extract, there are
listed all the I/Os used by the reference
application, in order to drive the L99DZ100.
Specifically:
➢ SPI
➢ CAN
➢ LIN
➢ NRESET
➢ NINT
➢ DIR_x
➢ CM

ST Confidential
Door Zone
FTDI-USB Interface 4

The PC-GUI USB interface is made with a small pluggable pcb

hosting an FTDI FT232RL chip.
The FTDI chip communicates with the uC unit by mean of the
UART protocol.

The two sections, the one with PC and the one with uC
(USB/UART) are interconnected with opto-couplers in order to
achieve Galvanic insulation and to protect PC in case of possible
short circuits on the pcb during tests.

ST Confidential
Door Zone
Chipboard Interface 5

The Chipboard interface is a small separated pcb hosting either L99DZ100G or L99DZ120.
On the back side some ceramic capacitors are accommodated.
These capacitor are connected to LDO1, LDO2, CP, VS.

ST Confidential
Door Zone
Power Supply Section 6

Tr_d1 The Power Supply Section is mainly composed by:

D1 ➢ Tr_d1: Back to back 40V TVS protection.

➢ D1: Diode for VSREG reverse polarity protection.
T1 ➢ T1: STD80N4F6, N-MOS for VS reverse polarity protection.
➢ T10: npn BJT for fast T1 discharge.
T10 ➢ J1: Battery Connection, reverse polarity protected.
➢ JP1: VSREG Jumper, useful to measure VSREG line consumption.
➢ JP3: VS Jumper, useful to measure VS line consumption.
➢ JP4: Jumper to disconnect C3 electrolytic capacitor for Power Window.
➢ C3: 2200uF electrolytic capacitor connected to VS.
➢ C1: 47uF electrolytic capacitor connected to VSREG.
J1
JP1
JP3
JP4
C3
C1

ST Confidential
Door Zone
Output Section 1/2 7

➢ OUT-01: Half Bridge Output, 300mΩ

➢ OUT-02: Half Bridge Output, 2Ω
➢ OUT-03: Half Bridge Output, 2Ω
➢ OUT-04: Half Bridge Output, 150mΩ
➢ OUT-05: Half Bridge Output, 100mΩ
➢ OUT-06: Half Bridge Output, 300mΩ
➢ OUT-07: High Side Output, 500mΩ
➢ OUT-08: High Side Output, 800mΩ
➢ OUT-09: High Side Output, 2Ω
➢ OUT-10: High Side Output, 2Ω
➢ OUT-11: High Side Output, 5Ω
➢ OUT-12: High Side Output, 5Ω
➢ OUT-13: High Side Output, 5Ω
➢ OUT-14: High Side Output, 5Ω
➢ OUT-15: High Side Output, 5Ω
➢ OUT-HS: High Side Output, 5Ω

ST Confidential
Door Zone
Output Section 2/2 8

➢ J28: Power Window Output.

Here is possible to connect any DC motor
suitable for Power Window application.
This output is driven by 4 STD80N4F6
Automotive-grade N-channel 40 V, 5.5
mOhm typ., 80 A.
➢ J24: EC Mirror Output.
➢ J32: Heater Output. ➢ P4: LDOs ➢ P1: CAN Transceiver
• LDO1 Output • CAN_L (1)
• LDO2 Output • GND (2)
➢ P5: SPI • CAN_H (3)
• GND ➢ P2: LIN Transceiver
• CSN • GND (1)
• MISO • LIN (2)
• MOSI
• CLK
➢ J2: CAN Transceiver
• CAN_L (2)
• CAN_H (7)

ST Confidential
Door Zone
L99DZ100G(P): Graphical User Interface 99

Main Window Tour

SPI Register Map Overview

Standard Control TAB

Output Controls TAB: Half Bridges

Output Controls TAB: High Sides

Output Controls TAB: PWM Config / DC Compensation

Electro Chrome Mirror Control TAB

Power H-Bridge Control TAB

SPI Control Registers (example)

Watchdog/POR Setting TAB

ST Confidential
Door Zone Main window (1/2) – Overview
10
Menu
Comminication Board Status
Exit
Communication Last data exchanged with GUI
WDC Trigger, GSB(N), FS, CM …
View Status Registers Clear
Settings
Testing
Debug
Help

GUI Version

Information about GUI

type, revision and
release date

Communication Status HW Information USB Information

Green = OK Information about connected Information about USB
Orange = Problem with board and Bolero uC firmware Interface and Serial Port
board detection revision connected

ST Confidential
Door Zone
Main window (2/2) – Menu Items 11
Menu Structure
Exit – Closes the GUI Periodical Status Refresh - en/dis. periodical refresh
Communication of status registers if Tab Standard control active
Periodical Status Clear – en/ dis periodical refresh and
clear of status registers if Tab Standard control active
View
Periodical Status Refresh - en/dis. periodical refresh
Settings
of status registers if Tab Output control active
Periodical Status Clear – en/ dis periodical refresh and
clear of status registers if Tab Output control active

Periodical Status Refresh - en/dis. periodical refresh of

status registers if Tab Partial Network control active

Periodical Refresh - en/dis. periodical refresh of SPI

Controls registers if Tab SPI Controls Regs control active

Periodical Refresh - en/dis. periodical refresh of SPI

Status registers if Tab SPI Status Regs control active

Periodical Refresh - en/dis. periodical refresh of SPI

History if Tab SPI History control active

Testing Open On Line Testing Window

About – information about the board

Help
and GUI

ST Confidential
Door Zone
SPI Registers Map Overview 12

Registers Addresses

Registers Names

Registers Values
(hexadecimal)

Registers Values
(binary)

ST Confidential
Door Zone
Standard Controls TAB (1/2) 13

The Standard Control Tab provides several controls related to the general settings of the device.
Here you can find controls for:
- V2 Settings
- Timers
- WU Settings
- WDC Settings
- Transceivers Settings
- Supply Voltage Monitoring
- Mode Control

Beside control settings

you can find some diagnosis
functions:
- Error Flags
- Bus Error Flags
- Power-ON / Wake-Up
- Thermal Clusters Info
- Global Status Byte

ST Confidential
Door Zone
Standard Controls TAB (2/2) – Device Diagnosis 14

Error Flags
Visualization of all
error flags

Transceivers Error Flags

Visualization of all error flags

Power On and Wake Uo diagnosis

Visualization of all Power On /
WDC / Wake Up flags

Device Status Information

Thermal Clusters temperature
Supplies Voltage Values
WU Input voltage
Thermal Clusters Warning
Thermal Clusters Shut Down

ST Confidential
Door Zone
Outputs Controls TAB (1/5) 15

Bridge Outputs PWM Settings

Control

Current Monitor
Settings
Automatic DC
Compensation –
VLed Settings

Over Current Thermal

Expiration Output
Settings

Over Current
Recovery Frequency FSO LS Over High Side Outputs
Mirror Heater Control DIR Control
Current Control

ST Confidential
Door Zone
Outputs Controls TAB (2/5) – Half Bridge Outputs 16

Show dialog fro AR

timing setup Autorecovery
Enable auto-recovery
Out Indicator feature on All Outputs
Colored if output is
active
Green = HS
Orange = LS

Miroro Positioning
Virtual keyboard for mirror
position adjustment:
Up, Down, Left, Right

Error Signalisation
Yellow flag = Open Load Lock Control

( OL @ Out 2 LS) Control of the Lock and

Safe-lock motors

Mirror Foldering
Autorecovery
Error Signalisation
Control of folding mirror
Enable auto-recovery
Red flag = Over Current
feature at Output

ST Confidential
Door Zone
Outputs Controls TAB (3/5) – HS Outputs Controls 17

OUT RON
Error Signalisation
Select HI / LO
RDS ON Red flag = Over Current
(OC @ Out 5 HS)

OUT Mode Control

Turn on/off
PWM Mode
Timer1/2
Autorecovery DIRECT DRIVE 1/2
Enable auto-recovery
feature at Output

Error Signalisation
Yellow flag = Open Load
( OL @ Out 7)

Diag Setting
Open Load Level
Over Current Level

ST Confidential
 Door Zone
Outputs Controls TAB (4/5) – PWM Configuration / DC
Compensation – VLed Settings 18

PWM Frequency Selection

PWM Duty Cycle
Sets the frequency
Sets duty cycles
independently for the 10
independently for the 10
PWM channels
PWM channels
(4 possible values)

PWM Duty Cycle PWM Frequency Selection

Indicators of actual Indicators of actual PWM
PWM duty cycle for frequency for each channel
each channel

VLed Settings
VLed Settings
Automatic Duty Cycle
compensation VLED Automatic Duty Cycle
voltage set compensation Enable

ST Confidential
Door Zone
Electro Chrome Mirror Control TAB 19
Error flags
ECM System Control Indication of Low or
High EC voltage
Overview of ECM
system configuration
SPI bits indicator
and actual state
Visualization of
important control bits

Autorecovery
Enables auto recovery
feature for output

ECM System Control Brigthness Indicator

ECV ON/OFF EC voltage level in
hex and binary form

ECM System Control

EC Enable

Brigthness Control

Brightness Control ECV HV bit setting

Set voltage on EC
glass = brightness

ST Confidential
Door Zone
Power H-Bridge Control TAB (1/3) 20
H-Bridge Circits
visualisation
Overview of
H-Bridge control system
configuration. (current
flow, Decay Mode)

H-Bridge control
Power H-Bridge
control and
configuration

H-Bridge control
Power H-Bridge Enable
Dual Motor Mode

Error Flags
Error flags related
to Power
H-Bridge
Drain – source
monitoring

ST Confidential
Door Zone
Power H-Bridge Control TAB (2/3) 21
Direction
Start
Select if HS1-LS2 or
Starts generate
HS2-LS1 bridge
PWM signal to
branch to be used for
drive the H-Bridge
motor supply

PWM Frequency
PWM Duty Cycle Sets PWM
Select PWM duty frequency in range
cycle = motor 1 .. 20kHz
rotation speed

Slew Rate Current

Cross Current Adjust gates

protection time current shape to
optimize EMC
Select bridge
death time

OL Test
Decay Mode Select configuration
selection for H-Bridge
Select Decay on diagnosis
LS or HS; free
wheeling
D-S Threshold
Sets D-S monitoring
voltage threshold

ST Confidential
Door Zone
Power H-Bridge Control TAB (3/3) 22

Motor Current
Visualization of
current through
motor
Decay

Decay current
visualization

Error Flags
Error flags related to
Power
H-Bridge
Drain – source
monitoring

H-Bridge control
Clear Power H-Bridge Enable
Clears Dual Motor Mode
corresponding SPI
status register

ST Confidential
 SPI Control Registers – an example
Door Zone
23

Red Color Control Registers

Red color indicates Control Registers
values changed by Names and
user, which are not Addresses
yet sent to
L99DZ100P

Bold Font
Bold are marked all
values what were
changed from Value change
previous state Click to any of these
(after receive from fields to change
L99DZ100P ) Register value
(available for all
control registers)

Read/ Write Buttons

Sends / Reads the
value of control CR Byte Value
register to/ from
Hexadecimal Value of
L99DZ80
the register

ST Confidential
Door Zone
SPI Status Registers – an example 24

Statusl Registers Status Registers

Status Registers Actual Content of the
Names and register
Addresses

Read / Clear Buttons

Reads or Reads and
Clear values of
L99DZ100P selected
status register

ST Confidential
Door Zone
Watchdog/POR settings TAB 25

LOW timing Adjustment Enable

Control of standby
Drag this line to desired mode of L99DZ100P
Long Open Window
timing setting

Send LOW Watchdog Timing

Send settings of watchdog
Watchodg trigger Long Open Window
timing Adjustment
Drag this line to desired
watchdog refresh time
position

Send Watchdog Timing

Send settings of watchdog
refresh time to board and
use it from next period

ST Confidential
Door Zone
L99DZ1xx: References 26
26

L99DZ100G, L99DZ100GP datasheet, DocID029077 Rev 4, September 2016

L99DZ120 datasheet, DocID029145 Rev 4, November 2016

P16_0131-1_011_L99DZ100GP_L22_report00, 2016 C&S group GmbH

P16_0131-2_009_HS_L99DZ100G_report00, 2016 C&S group GmbH

P16_0131-3_015_HS_PN_L99DZ100G_Report00, 2016 C&S group GmbH

P16_0258_011_L99DZ120BB_L22_Report00, 2016 C&S group GmbH
EMC Test report IBEE 10-07-16 L99DZ100GP, IBEE
EMC Test report 02-11-16 L99DZ120BB, IBEE

ST Confidential