THE NEW D-700-MK3

▪ BOTH AMF AND

SYNCHRONIZING
▪ SAME UNIT FOR ALL FUNCTIONS
▪ INTERNET BASED
▪ MULTI-PROTOCOL
▪ FLEXIBLE WITH PLUG-IN
MODULES
▪ AUTO LEARNING

FEATURES

• Diesel and gas genset support • DC genset functionality • Multiple load management
• 400Hz operation support • DPF regeneration functionality • Current unbalance protection
• 400 event logs, full snapshot • Peak Lopping / peak shaving • Voltage unbalance protection
• All parameters front panel • Mains de-coupling protection • Fuel filling & fuel theft alarms
editable • R.O.C.O.F protection • Contactor & MCB drive
• 3 level configuration password • Vector shift protection • Battery back-up real time clock
• 4.3” 480x272pixels color LCD • Reverse power protection • Idle speed control
• Downloadable languages • Over/under freq. Protection • Battery charge run enabled
• Waveform display of V & I • Over/under voltage protection • Combat mode support
• Harmonic analysis of V & I • Smart load management • Multiple nominal conditions
• Synchroscope & check synch • Smart genset sequencing • 4 quadrant genset power
• Allows closed transfers • Run/stop priority support counters
• 12 configurable digital inputs • Equal aging of gensets • Mains power counters
• Inputs expandable to 44 • Base load (power export) • Fuel filling counter
• 8 configurable digital outputs • Unmanaged distributed power • Fuel consumption counter
• Outputs expandable to 40 export support • Modem & ethernet diagnostics
• 7 configurable analog inputs • AVR & GOV droop support • Configurable through USB,
• 2 configurable analog outputs • Dead bus sensing RS-485, Ethernet and GPRS
• Both CANBUS-J1939 & MPU • Multiple automatic exerciser • Free configuration program
• 3 configurable service alarms • Weekly operation schedule • Allows SMS controls
• Multiple topologies • Dual mutual standby with • Ready for central monitoring
• 6xCT, true mains metering equal aging of gensets ethernet & GPRS
• Supports up to 48 gensets • Manual “speed fine adjust” on • SNMP v1 v2c v3 support
• Automatic learning/self adjust selected ECUs • Mobile genset support
• Direct governor & AVR control • Automatic fuel pump control • Automatic GSM geo-location
• Voltage and phase matching • Disable protections feature • GPS connectivity (USB&RS232)
• kW & kVAr load sharing • Excess power protection • Dynamic DNS support
• True soft transfer in both ways • Reverse power protection • Easy USB firmware upgrade
• PLC functions • Overload IDMT protection • IP65 rating with standard gasket
• Load shedding, dummy load
 PLUG-IN MODULES FUNCTIONALITIES COMMUNICATIONS
▪ 2G GSM Modem ▪ Multi genset synch & load share ▪ Central Monitoring
▪ 3G-2G GSM Modem ▪ Mains synchronization ▪ Embedded Web Server
▪ 4G-3G-2G (CAT-4) Modem ▪ Single genset parallel with mains ▪ USB
▪ NB/IOT,CAT-M1,2G Modem ▪ DC genset controller ▪ GPS (geo-location)
▪ Wi-Fi (802.11 b/g/n) ▪ AMF unit (uninterrupted transfer) ▪ SMS
▪ Ethernet 100 Mbps ▪ ATS unit (uninterrupted transfer) ▪ E-mail
▪ USB Host ▪ Remote start controller ▪ Modbus
▪ RS-232 (isolated) ▪ Manual start controller ▪ Modbus TCP/IP
▪ RS-485 (isolated) ▪ Engine controller ▪ SNMP v1 v2c v3
▪ Synchro/LoadShare Module ▪ Remote display panel ▪ HTML
▪ 3x AC Current Inputs ▪ UDP
▪ 3x Analog Inputs & 2x Analog ▪ SNTP
Outputs
▪ DC Voltage and Current Inputs
▪ Tilt Detector

Backpanel view

Plug-in modules

MULTI GENSET SYNCHRONIZATION MAINS SYNCHRONIZATION

Up to 48 gensets may be paralleled on the same Up to 16 mains controller per system are
busbar. Smart load management is a standard supported. Mains controllers provide the
feature. REMOTE START signal and handle
synchronization of the complete genset system
with mains.
TO LOAD

LOAD
Datalink
DATALINK
Bus To mains GENSET
BUS
controller BUSBAR
s TO GENSET
CONTROLLERS
 SCOPEMETER & HARMONICS RAINBOW SCADA CENTRAL MONITORING

RAINBOW PLUS PROGRAM WEB SERVER

TECHNICAL SPECIFICATIONS
Alternator voltage: 0 to 300 V-AC (Ph-N) RS-232 Port: selectable baud rate (2400-115200baud)
Alternator frequency: 0-600 Hz. Operating temperature: -20°C to 70°C (-4 to +158 °F)
Mains voltage: 0 to 300 V-AC (Ph-N) Storage temperature: -40°C to 80°C (-40 to +176°F)
Mains frequency: 0-600 Hz. Maximum humidity: 95% non-condensing.
Topology: 1-2-3 phases, with or without neutral IP Protection: IP65 from front panel, IP30 from the rear (with
DC Supply Range: 8.0 to 36.0 V-DC. gasket)
V-A-cos Accuracy: 0.5% + 1 digit Dimensions: 245 x 188 x 36mm (WxHxD)
kW-kVA-kVAr Accuracy: 1.0% + 1 digit Panel Cut-out Dimensions: 216 x 156 mm minimum.
Current consumption: 500 mA-DC max. Weight: 800 g (approx.)
Current Inputs: from current transformers. ../5A or ../1A. Case Material: High Temperature, non-flammable ABS/PC
Digital inputs: input voltage 0 to 36 V-DC. Installation: Flat surface mounting on a Type 1 enclosure. Rear
Analog input range: 0-5000 ohms. retaining plastic brackets.
Mains and genset contactor outputs: 16Amps@250V
DC Outputs: Protected mosfet semiconductor outputs,
CONFORMITY
rated 1Amp@28V-DC
Cranking dropouts: survives 0V for 100ms.
Magnetic pickup voltage: 0.5 to 50Vpk. EU Directives Conformity
Magnetic pickup frequency: 0 to 20000 Hz. -2014/35/EC (low voltage)
Charge Alternator Excitation: 2W. -2014/30/EC (electro-magnetic compatibility)
Display Screen: 4.3”, 480x272 pixels, color Norms of reference:
Ethernet Port: 10/100 Mbits EN 61010 (safety requirements)
USB Device: USB 2.0 Full speed EN 61326 (EMC requirements)
USB Host: USB 2.0 Full speed UL & CSA Compatibility:
RS-485 Port: selectable baud rate (2400-115200baud) • UL 6200, Controls for Stationary Engine Driven Assemblies
(File# - 20140725-E314374)
• CAN/CSA C22.2 No. 14-13 – Industrial Control Equipment
TYPICAL CONNECTIONS