Scribd
Upload
29 views3 pages

Module Guidelines

i just need the project concerning the smart door lock system

Uploaded by

graysonjunior85
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
29 views3 pages

Module Guidelines

i just need the project concerning the smart door lock system

Uploaded by

graysonjunior85
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Module Information

Module Code: ETU 07112


Module Title: Fundamentals of Analogue Electronics
Module Credits: 10

Module Master: Mr. Athumani O. Mfinanga (Office location: Block B, 3rd


floor, small room adjacent to B11 class; Mobile: 07-54/15-
319685; E-mail: [email protected])

Module Contents and guidelines

1. Fundamentals of Electronic Circuits


 Basic Concepts
 Electronic Components
 Device Numbering Systems
 Electronic Instruments
2. Introduction to the transistors (BJT and JFET)
 Construction and operation
 Basic parameters and characteristics
 Operation of transistor circuits (amplifier, switch, oscillator)
 Basic analysis of transistor circuits (amplifier, switch)
 Classes of amplifier
 Maximum transistor ratings
 Transistor datasheet
3. Op-amp
 Introduction to op-amps
 Op-amp input modes and parameters
 Basic op-amp circuits

Recommended references but no limited to:


 Thomas L. Floyd & David L. Buchla, (2014), Electronics Fundamentals
Circuits, Devices and Applications
 Theodore F. Bogart, Jr, Jeffrey S. Beasley, and Guillermo Rico (2004)
Electronic Devices and Circuits, 6th Edition, Prentice Hall.
 Robert L. Boylestad & Louis Nashelsky, (2013), Electronic Devices and
Circuit Theory, 11th Edition, Pearson.

1
Practical Works
Module Code: ETU 07112
Module Title: Fundamentals of Analogue Electronics
Module Credits: 10

Module Master: Mr. Athumani O. Mfinanga (Office location: Block B, 3rd


floor, small room adjacent to B11 class; Mobile: 07-54/15-
319685; E-mail: [email protected])

Practical Works to be conducted under each Topic

1. Fundamentals of Electronic Circuits


 Demonstration of Electronic components and measuring/testing Instruments
 Identification of Working and Faulty Electronic Components
 Construction and circuits’ parameters (voltage and current) measurements of
series and parallel circuits. (Required components: Resistors)
2. Introduction to the transistors (BJT and JFET)
 Realization of transistor’s parameters (β & α)
 Determination of Transistor’s states (Saturation and cut-off)
 Demonstration on how a transistor can be used as a switch
 Construct and demonstrate the operation of a Class A power amplifier circuit
 Construct and demonstrate the operation of a Class B power amplifier circuit
3. Op-amp
 Construct and demonstrate the operation of inverting and noninverting
amplifier circuits using op-amp
 Construct and test an op-amp comparator, an integrator and a differentiator
circuit

2
Assessment Plan
Module Code: ETU 07112
Module Title: Fundamentals of Analogue Electronics
Module Credits: 10

Module Master: Mr. Athumani O. Mfinanga (Office location: Block B, 3rd


floor, small room adjacent to B11 class; Mobile: 07-54/15-
319685; E-mail: [email protected])

Method of Assessment

 Continuous Assessment (CA) 60%


 Final Examination (FE) 40%

Continuous Assessment (CA) Components

 Assignements (At least 3) 10%


 Presentations (At least 2) 5%
 Practicals (At least 3) 15%
 Test I 15%
 Test II 15%

You might also like