Scribd
Upload
41 views3 pages

Tutorial 5

Uploaded by

Shriram A ep23b019
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
41 views3 pages

Tutorial 5

Uploaded by

Shriram A ep23b019
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

EE2015: Electric Circuits and Networks

Tutorial 5
(September 13, 2024)

1. Let the open circuit impedance matrix of network N be


 
0 −r
.
r 0

1
Zin ZL
N
1’

Find Zin (s) in terms of r and ZL (s). If ZL (s) is 1/sC, show that the network behaves
like an inductor at the input terminals.
2. Find the Z parameters for the 2 port network marked with dotted lines and then find
the Zout (impedance seen by the 1kΩ resistor) for the terminated two port network.

I1 → ← I2
200Ω + +

10−3 V2
−
+ Vs V1 5kΩ 20I1 V2 3kΩ 1kΩ

− −

3. The two port network N is an RLC network. If i1 (t) = δ(t), v2 (t) = (3e−t + 5e−t )u(t).
a. If j2 (t) = u(t), find e1 (t)
b. If j2 (t) = cos 500tu(t), find the response e1 (t).

EE2015 Tutorial 5 Page 1 of 3


+ +
i1 v1 N v2
- -

+ +
e1 N e2 j2
- -

4. For the circuit given below, use reciprocity and superposition to determine Vout in terms
of Vk , k = 1, 2, . . . , 6.

2Ω 1Ω V5 1Ω V6
+
+
−

+
−
2Ω 2Ω 2Ω
V1 +
− Vout
+
− V2 +
− V3 V4 +
−

5. The two-port network shown below can be viewed as a cascaded combination of three
two-port networks A, B, and C.
(a) Find the transmission parameters of each network.
(b) Find the transmission parameters of the overall network.

I1 1Ω 3Ω 5Ω I2
+ +

V1 2Ω 4Ω 6Ω V2

− −

A B C

EE2015 Tutorial 5 Page 2 of 3 13.09.2023


1A
+ I1 h11 = 25 Ω 2A
h12 = 4
h21 = −4
1′ A h22 = 1 S 2′ A I2
+
6. A series-parallel connection of two V1 V2
two-port networks is shown on the −
right. Terminals 1’A and 2’A and 1′ B h11 = 16 Ω 2B
1’B and 2’B are connected. Deter- h12 = 1
mine the z-parameters of the overall h21 = −1
network. − h22 = 0.5 S 2′ B
1B
7. In the circuit below, find the z parameters individually for the networks A and B. Now, if
a voltage source Vs is connected between terminals a and b and a load resistor RL = 10Ω
is connected between terminals c and d, find the voltage gain VV41 using the z parameters
of the networks A and B.

+ a +
2Ω 4Ω + + 4Ω 8Ω c
V1 10Ω V2 V3 20Ω V4
- -
- _
b A B d

EE2015 Tutorial 5 Page 3 of 3 13.09.2023

You might also like