Danfoss 90

Parts Manual
Series 90
100cc Axial Piston Pump
www.danfoss.com
Parts Manual
Series 90 Pumps, 100cc
Revision history Table of revisions
Date Changed Rev
June 2022 Corrected various part numbers 0401
June 2020 Corrected lip seal and seal carrier assembly part numbers; changed document number from 0311
'AX00000093'
January 2020 Corrected filter description for filtration option 9 0209
July 2019 Corrected control part numbers 0208
November 2018 Obsoleted screw part numbers in charging system 0207
September 2018 Removed old part number from common parts section 0206
February 2018 Removed part number from seal kit 0205
January 2018 Fixed typo 0204
December 2017 Updated to Engineering Tomorrow 0203
2 | © Danfoss | June 2022 AX152886482434en-000401

Parts Manual
Contents
General Information
Service parts identification........................................................................................................................................................... 6
Nameplate...........................................................................................................................................................................................6
Date code............................................................................................................................................................................................ 7
About service bulletins...................................................................................................................................................................7
Procedure to identify a part..........................................................................................................................................................7
Regional part numbers............................................................................................................................................................. 7
Example of a part identification (S90 100cc).....................................................................................................................7
Adobe Acrobat 2-page viewing.................................................................................................................................................. 8
Order code.......................................................................................................................................................................................... 9
Common parts and special hardware
Common parts................................................................................................................................................................................ 10
Special hardware EAB, EAS, EED............................................................................................................................................... 14
Special hardware EBC, EFC, EEB, EEG...................................................................................................................................... 16
Special hardware EFI-SKA, FAA-FAD....................................................................................................................................... 18
Special hardware FAL-FAU......................................................................................................................................................... 22
Special hardware FAW, FAZ, FAX............................................................................................................................................. 26
Special hardware FBA-GAA........................................................................................................................................................ 28
Special hardware GB1, GB4, GB8.............................................................................................................................................. 30
Special hardware GBA-GBT........................................................................................................................................................ 34
Special hardware GCA-GFJ......................................................................................................................................................... 38
Special hardware GFK-GP4......................................................................................................................................................... 42
Special hardware GTB-JCB.......................................................................................................................................................... 46
Special hardware JCC-PEB.......................................................................................................................................................... 48
Special hardware PGA and PGB................................................................................................................................................ 52
Displacement limitation
Displacement limitation 2-4.......................................................................................................................................................54
Displacement limitation 7...........................................................................................................................................................56
Displacement limitation 8, B...................................................................................................................................................... 58
Displacement limitation D..........................................................................................................................................................60
Displacement limitation E, F...................................................................................................................................................... 62
Displacement limitation H..........................................................................................................................................................64
Displacement limitation P...........................................................................................................................................................66
End cap
End cap H, 2, 6, 60-65 (built in US)........................................................................................................................................... 68
End cap 60, 62, 67 (built in Germany)..................................................................................................................................... 70
End cap 1, 8, 8G, M, 80-82........................................................................................................................................................... 72
End cap 8M, 8W.............................................................................................................................................................................. 74
End cap 80, 8C (built in Germany)............................................................................................................................................76
End cap 8P, 8S................................................................................................................................................................................. 78
End cap 8E, 8F..................................................................................................................................................................................82
End cap 8K, 8N.................................................................................................................................................................................86
Charging system
Charging system 3, D-G............................................................................................................................................................... 90
Charging system M, N, S, X......................................................................................................................................................... 94
Auxiliary mounting
Auxiliary mounting AB and AC..................................................................................................................................................96
Auxiliary mounting AG-BB and V............................................................................................................................................. 98
Auxiliary mounting BC, BD, BE................................................................................................................................................100
Auxiliary mounting BF and BL.................................................................................................................................................104
Auxiliary mounting BM, BU, C2, CA.......................................................................................................................................106
Auxiliary mounting CB, CC, CD............................................................................................................................................... 110
Auxiliary mounting CE, CJ, CK................................................................................................................................................. 112
Auxiliary mounting CP, CR....................................................................................................................................................... 114
Auxiliary mounting CT, CU....................................................................................................................................................... 116
Auxiliary mounting NN, NU......................................................................................................................................................118
© Danfoss | June 2022 AX152886482434en-000401 | 3

Parts Manual
Contents
Charge pressure setting

Charge pressure system 08-42 and XX................................................................................................................................ 120
Shaft
Shaft C6-S3.....................................................................................................................................................................................122
Shaft T2-TJ......................................................................................................................................................................................126
Controls
Control CA-DD.............................................................................................................................................................................. 128
Control EA-EP................................................................................................................................................................................ 130
Control EV-EZ................................................................................................................................................................................ 134
Control FA-FD............................................................................................................................................................................... 136
Control FG, FH...............................................................................................................................................................................138
Control GA......................................................................................................................................................................................140
S90P control HD, HE....................................................................................................................................................................142
Control HF-HS............................................................................................................................................................................... 144
Control HT-JC................................................................................................................................................................................ 146
Control K1-K9................................................................................................................................................................................ 150
Control KA-KF................................................................................................................................................................................154
Control KK-KP................................................................................................................................................................................158
Control KT-KW...............................................................................................................................................................................162
Control LE, LG................................................................................................................................................................................164
Control LR, LS................................................................................................................................................................................ 166
Control LW..................................................................................................................................................................................... 168
Control M1, M2............................................................................................................................................................................. 170
Control M7, M8............................................................................................................................................................................. 172
S90P control M9........................................................................................................................................................................... 174
Control MA, MB............................................................................................................................................................................ 176
Control MC, MD............................................................................................................................................................................178
Control ME, MH............................................................................................................................................................................ 180
Control MK, ML............................................................................................................................................................................. 182
Control MN.....................................................................................................................................................................................184
Control MO, MS............................................................................................................................................................................ 186
Control MT, MU............................................................................................................................................................................ 188
Control MV, MY.............................................................................................................................................................................190
Control NA......................................................................................................................................................................................192
Control NU..................................................................................................................................................................................... 194
Control PA, PB............................................................................................................................................................................... 196
S90P control PE.............................................................................................................................................................................198
Control PF, PH, PJ.........................................................................................................................................................................200
Control RR, RS................................................................................................................................................................................202
S90P control RU............................................................................................................................................................................204
Control SA, SB, SD, SE................................................................................................................................................................. 206
Filtration
Filtration 0-9.................................................................................................................................................................................. 208
Filtration A-L..................................................................................................................................................................................212
Filtration P-X..................................................................................................................................................................................216
High pressure protection
High pressure protection 1-7, A-F......................................................................................................................................... 220
High pressure protection G-P..................................................................................................................................................224
High pressure protection R, T..................................................................................................................................................228
High pressure protection V, Z................................................................................................................................................. 230
Orifice
Orifice 00-26.................................................................................................................................................................................. 232
Orifice 28-40.................................................................................................................................................................................. 236
Orifice 45-99.................................................................................................................................................................................. 240
Orifice A3-C1..................................................................................................................................................................................244
Orifice C3-GD.................................................................................................................................................................................248

Parts Manual
Contents
Orifice GF-Z3..................................................................................................................................................................................252
Overhaul seal kit
Seal kit..............................................................................................................................................................................................254
Service bulletin
AN152886483362........................................................................................................................................................................ 255
AN152886483362 charge pump replacements............................................................................................................... 256
SB-1988-009...................................................................................................................................................................................257
SB-1988-016...................................................................................................................................................................................259
SB-1988-023...................................................................................................................................................................................261
SB-1989-002...................................................................................................................................................................................263
SB-1989-003...................................................................................................................................................................................264
SB-1989-006...................................................................................................................................................................................266
SB-1989-023...................................................................................................................................................................................268
SB-1992-003...................................................................................................................................................................................270
SB-1992-011...................................................................................................................................................................................272
SB-1993-001...................................................................................................................................................................................273
SB-1993-015...................................................................................................................................................................................276
SB-1994-017...................................................................................................................................................................................278
SB-1994-018...................................................................................................................................................................................279
SB-1994-035...................................................................................................................................................................................281
SB-1994-36..................................................................................................................................................................................... 283
SB-1995-003...................................................................................................................................................................................284
SB-1995-025...................................................................................................................................................................................285
SB-1996-009...................................................................................................................................................................................287
SB-1997-048...................................................................................................................................................................................288
SB-1998-018...................................................................................................................................................................................290
SB-1998-041...................................................................................................................................................................................292
SB-1998-066...................................................................................................................................................................................294
SB-1998-070...................................................................................................................................................................................296
SB-1999-019...................................................................................................................................................................................298
SB-1999-041...................................................................................................................................................................................299
SB-1999-057...................................................................................................................................................................................301
SB-1999-065...................................................................................................................................................................................302
SB-2000-022...................................................................................................................................................................................304
SB-2000-041...................................................................................................................................................................................306
SB-2001-013...................................................................................................................................................................................307
SB-2002-050...................................................................................................................................................................................309
SB-2005-011...................................................................................................................................................................................310
SB-2007-018...................................................................................................................................................................................311
SB-2007-027...................................................................................................................................................................................313
SB-2007-051...................................................................................................................................................................................315
SB-2007-055...................................................................................................................................................................................317
SB-2009-035...................................................................................................................................................................................319
SB-2009-038...................................................................................................................................................................................320
SB-2009-049...................................................................................................................................................................................321
SB-2009-073...................................................................................................................................................................................322
SB-2013-011...................................................................................................................................................................................324
SB-2015-005...................................................................................................................................................................................325

Parts Manual
General Information
Service parts identification

The following information and procedure is used to identify the module group, item number,
manufacture date, part number, and part name of the parts included in the .
The parts listed include all parts which may be used when performing either “Minor Repairs”, “Major
Repairs” or “Conversions” on the .
Nameplate
Each unit will have a nameplate affixed to the housing. The nameplate of the will include the following
information:
Model code
The Danfoss model code completely defines the specific unit and must be used when ordering parts to
service this product.
Model/material number
The Danfoss model number (also known as material number) is used by the factory in manufacturing. On
repeat orders, a complete unit can be ordered by the model number.
Serial number
The Danfoss serial number is used to identify the manufacture date and the unit sequence in the build.
The serial number is also used to identify the units warranty time period.
The letter code indicates the location of original manufacture (assembly).
The first number (2 digits) indicates the year of manufacture. The second number (2 digits) indicates the
calendar week of manufacture.
The third number (5 digits) is a sequential number used to identify a specific unit.
Model No./Ident No. 9621161

Model Code 90 L 100 EP 1
CD 60 P 3 F1 D
03 GBA 35 35 24
Serial No. A-01-26-23456
Made in U. S. A.

Parts Manual
General Information
Date code
The date code is defined as the year and week of manufacture. The same item number may list more than
one part number. This indicates that there is more than one configuration for that item number. You will
see that there are different date codes for the different part numbers. Find the date code of your unit
from the nameplate to determine which service part number you need to order.
Example: The service part desired is item G30

Order Code Item Date Begin Date End Part Number Part Name Qty. per
Model/Kit
80 G30 89-17 8000243 End cap gasket 1
G30 89-16 8000151 End cap gasket 1
(SB-1995-006)
All units using this order code with a date code prior to 89-17 must use part number “8000151.” All units
with a date code of 89-17 and newer must use part number “8000243.”
About service bulletins

A Service Bulletin Number (SB-_ _ _ _ - _ _ _) may follow the “Part Name” of the part you desire. You must
read that Service Bulletin prior to ordering that part. The information contained in these Service Bulletins,
as of the print date of this bulletin, are included at the end of this manual. Service Bulletins contain more
detailed information such as interchangeability, what additional parts are involved, etc. It is suggested
that you add additional Service Bulletins to this manual as you receive them.
Procedure to identify a part

The modular design of this product results in a simplified service parts list and part number identification
procedure.
The same item numbers are used for same part names on all units within a product type. A part number
that has another number following it in parentheses is done to make this a world wide manual.
Regional part numbers

Some part numbers are region specific and should be ordered accordingly.
As an example, the part number (example: 314583 (9008000-0118) will be used. The first number is sold
in Germany. The number in parentheses is sold in the United States. Customers would order
9008000-0118 if ordering the part in the United States.
Example of a part identification (S90 100cc)

The nameplate on a Series 90 pump has an Order Code of 90L100 EP 1 CD 60 P 3 F1 D 03 GBA 35 35 24.
Use the following procedures to determine the part number of the drive shaft used on this pump.
1. Referring to the input shaft module in the Order Code, the input shaft option for this pump is
identified by the code “S1. (90L100 EP 1 CD 60 P 3 F1 D 03 GBA 35 35 24).
2. Referring to the Service Parts List, find the shaft group. Next find the order code that relates to this
unit, which is “F1”. The shaft is found to be item L100 and part number 8200170.

Parts Manual
General Information
Adobe Acrobat 2-page viewing

While viewing manual in Adobe Acrobat, the following settings need to be applied to ensure proper
page display.
1. Select “View” → “Page Display” → “Two Page View”
2. Select “View” → “Page Display” → “Show Cover Page in Two Page View”

Parts Manual
General Information
Order code
Series Displacement
M P J G N F L H T W Y Z K
9 0 L 1 0 0 E P 1 CD 6 0 P 3 F 1 D 0 3 G B A 3 5 3 5 2 4
Rotation
Control
Pressure regulation
Auxiliary mounting pad
End cap
Filtration
Shaft
Charging system
Control orifice
Special hardware features
High pressure setting port A
High pressure setting port B

Parts Manual
S90 100cc pump common parts

Parts configuration
B80 L60
L70
*B90
B70
B72 L40
*B90
B82
L20
B10 L50
*L25
QD50 L10
D55
F20 D65
M14 B50 B71
D10
D75
D70 B50 E30
E20
D85 E22
QB30 E80
D80
E24
D50 *E50
E90
QD50 E10
D55
D65
F20
M14
D10
E70 *E60
*E40
D75
D95 D70 D60 E30
D85 E80
D80 E24 E20
D50
Swashplate Leveler design

design prior 95-50 thru 06-26
to 07-28 (built in U.S.A.)
* Included in base pump seal kit Q210

Parts Manual
Item Date Begin Date End Part Number Part Name Qty. per
Model/Kit
B10 07-28 11002463 Housing (SB-1994-035 on page 281 & 1
SB-2007-018 on page 311)
B50 87-02 9004800-3708 Pin 2
B70 87-02 140644 (9005110-5600) Plug assembly 1
B71 87-02 327007 (9005110-4400) Plug assembly 1
B72 87-02 140644 (9005110-5600) Plug assembly 1
B80 87-02 664524 (9005110-9000) Plug assembly 1
B82 92-19 140644 (9005110-5600) Plug assembly (SB-1992-003 on page 270) 1
B90 87-02 9803390 Control filter screen 3
D10 07-29 521607 Servo arm assembly (SB-2007-018 on page 311) 1
D10 87-02 07-28 8200268 Servo arm assembly (SB-1993-015 on page 276) 1
D50 07-29 11002493 Swashplate (SB-2007-018 on page 311) 1
D50 88-16 07-28 8200232 Swashplate (SB-1988-009 on page 257) 1
D55 07-29 519150 Screw (SB-2007-018 on page 311) 1
D55 87-02 07-28 9007276-0111 Screw 1
D60 87-02 07-28 8800669 Swashplate guide (SB-2007-018 on page 311) 1
D65 07-29 9007375-0044 Screw (SB-2007-018 on page 311 1
D65 87-02 07-28 9007375-0032 Screw (SB-1992-011 on page 272) 1
D70 87-02 9009625-0146 Washer 1
D75 87-02 9004875-0098 Spiral head pin 1
D80 87-02 673038 (8200273) Cage locator link (SB-1994-017 on page 278) 1
D85 87-02 8801235 Pin (SB-1998-018 on page 290 & SB-1999-057 on 1
page 301)
D95 87-02 07-28 673145 (8200058) Spring (SB-2007-018 on page 311) 1
E10 07-29 11000790 Side cover (SB-2007-018 on page 311) 1
E10 95-50 07-28 501574 Side cover 1
E10 92-12 95-49 8510204 Side cover (SB-1995-025 on page 285, 1
SB-1997-048 on page 288, SB-1998-070 on page
296)
E10 87-02 92-11 8510132 Side cover (SB-1992-003 on page 270) 1
E20 06-27 11042019 Leveler 1
E20 95-50 06-26 8200393 Leveler (SB-1998-070 on page 296) 1
E20 92-12 95-49 8510204 Leveler (SB-1998-070 on page 296) 1
E20 87-02 92-11 8510132 Leveler (SB-1989-003 on page 264 & SB-1998-070 1
on page 296)
Part numbers are continued on the next 2 pages.

Parts Manual
B80 L60
L70
*B90
B70
B72 L40
*B90
B82
L20
B10 L50
*L25
QD50 L10
D55
F20 D65
M14 B50 B71
D10
D75
D70 B50 E30
E20
D85 E22
QB30 E80
D80
E24
D50 *E50
E90
QD50 E10
D55
D65
F20
M14
D10
E70 *E60
*E40
D75
D95 D70 D60 E30
D85 E80
D80 E24 E20
D50
Swashplate Leveler design

design prior 95-50 thru 06-26
to 07-28 (built in U.S.A.)

Parts Manual
Model/Kit
E22 06-27 517936 Spring seat 2
E22 95-50 06-26 none Spring seat 0
E22 92-12 95-49 8510204 Spring seat replacement kit (SB-1998-070 on 2
page 296)
E22 87-02 92-11 8510132 Spring seat replacement kit (SB-1998-070 on 2
page 296)
E24 87-02 8801225 Shim (SB-1989-003 on page 264 & SB-2000-041 2
on page 306)
E30 09-52 11056531 Guide post (SB-1998-070 on page 296 & 2
SB-2009-073 on page 322)
E30 92-12 97-46 8510204 Guide post replacement kit (SB-1997-048 on page 2
288)
E30 87-02 92-11 8510132 Guide post replacement kit (SB-1998-070 on page 2
296)
E40 87-02 505412 (9003509-0008) Seal nut 2
E50 87-02 517378 (9004104-1620) O-ring 1
E60 87-02 517228 (5000206) Screw (SB-1994-018 on page 279) 6
E70 87-02 664524 (9005110-9000) Plug assembly 1
E80 87-02 334979 (11062690) Spring 2
E90 95-50 513889 Insert assembly (SB-1995-025 on page 285 & 1
SB-1999-041 on page 299)
F20 88-16 11116312 Slider block (SB-1988-009 on page 257, 1
SB-2009-049 on page 321 & SB-2015-005 on page
325)
L10 87-02 5000506 Roller bearing 1
L20 87-02 9006300-0175 Retaining ring 1
L25 87-02 521722 Seal carrier assembly (SB-2007-018 on page 311) 1
L40 07-29 519021 Lip seal (SB-2007-018 on page 311) 1
L50 87-02 327627 (9004104-1540) O-ring 1
L60 87-02 516768 Retainer plate 1
L70 87-02 041160 (9007314-0605) Screw 4
QB30 07-29 11131109 Cradle bearing assembly (SB-2007-018 on page 1
311)
QB30 87-02 07-28 305839 (8200053) Cradle bearing assembly 1
QD50 07-29 8200618 Swashplate assembly (SB-2007-018 on page 311) 1
QD50 88-16 07-28 346155 (8200192) Swashplate assembly (SB-1988-009 on page 257) 1

Parts Manual
S90 100cc pump special hardware EAB, EAS, EED

EAB, EAS, EED parts configuration
(EED)
B83
(EAB, EAS)
*QB83
B83
QC04
C20
C30
C40
C06 E82
C50 E82
*C70
C80
Generic speed sensor used to show part location only.

Parts Manual
Common parts
Model/Kit
C20 87-02 364000 Piston assembly (SB-1988-023 on page 261) 9
C30 87-02 11067351 Slipper guide 1
C40 88-22 334409 (8200144) Slipper guide bearing (SB-1988-016 on page 259) 2
C50 88-22 334383 (11065866) Spacer (SB-1988-016 on page 259, SB-1998-041 4
on page 292 & SB-2009-038 on page 320)
C65 88-22 98-47 Obsolete Washer (SB-1988-016 on page 259 & SB-1998-041 4
on page 292)
C70 88-22 314419 (9007276-0114) Screw (SB-1988-016 on page 259 & SB-1998-041 4
on page 292)
QB83 98-14 085043 (9004201-3700) O-ring 1
Order code: EAB

B83 94-14 KPPG12508 Speed sensor 1
C06 94-14 11093925 (11012435) Cylinder block assembly, with speed ring 1
C80 94-14 518929 Valve plate 1
E82 94-14 356576 (11062702) Spring 2
QC04 94-14 8510371 Cylinder block kit, with speed ring 1
Order code: EAS

C80 98-14 518929 Valve plate 1
E82 98-14 356576 (11062702) Spring 2
Order code: EED

B83 99-17 140644 (9005110-5600) Plug assembly 1
C80 99-17 518929 Valve plate 1
E82 99-17 356576 (11062702) Spring 2

Parts Manual
S90 100cc pump special hardware EBC, EFC, EEB, EEG

EBC, EEB, EEG, EFC parts configuration
(EEB & EEG)

(EBC & EFC)
B83
*QB83
B83
QC04
C20
C30
C40
C06
C50
*C70
C80
Generic speed sensor used to show part location only.

Parts Manual
Common parts
Model/Kit
C30 87-02 11067351 Slipper guide 1
on page 292 & SB-2009-038 on page 320)
on page 292)
on page 292)
QB83 98-14 085043 (9004201-3700) O-ring 1
Order code: EBC

C80 94-14 518806 Valve plate 1
Order code: EEB

B83 06-05 140644 (9005110-5600) Plug assembly 1
C80 06-05 518806 Valve plate 1
Order code: EEG

B83 00-13 140644 (9005110-5600) Plug assembly 1
C80 00-13 518931 Valve plate, CCW 1
C80 00-13 518930 Valve plate, CW 1
E82 00-13 356576 (11062702) Spring 2
Order code: EFC

C80 03-43 518806 Valve plate 1

Parts Manual
S90 100cc pump special hardware EFI-EKA, FAA-FAD

Parts configuration
(EFI, EHA & EKA)
B83
*QB83
B83
QC04
C20
C30
C40
C06
C50
*C70
C80
(FAA, FAB, FAC & FAD)
B83
QC04
C20
C30
C40
C05 E82
C50 E82
*C70
C80
Generic speed sensor shown

Parts Manual
Common parts
Model/Kit
C30 87-02 11067351 Slipper guide 1
on page 292 & SB-2009-038 on page 320)
on page 292)
on page 292)
Order code: EFI

C80 98-12 518930 Valve plate, CW 1
Order code: EHA

C80 00-42 518806 Valve plate 1
Order code: EKA

C80 99-31 518806 Valve plate 1
Order code: FAA

B83 87-02 140644 (9005110-5600) Plug assembly 1
C05 87-02 11012434 Cylinder block assembly 1
C80 87-02 518994 Valve plate 1
E82 87-02 356576 (11062702) Spring 2
QC04 87-02 8510372 Cylinder block kit 1
Order code: FAB

B83 87-02 140644 (9005110-5600) Plug assembly 1
C80 87-02 518927 Valve plate 1
E82 87-02 356576 (11062702) Spring 2
Part numbers continue to the next 2 pages.

Parts Manual
Parts configuration
(EFI, EHA & EKA)
B83
*QB83
B83
QC04
C20
C30
C40
C06
C50
*C70
C80
(FAA, FAB, FAC & FAD)
B83
QC04
C20
C30
C40
C05 E82
C50 E82
*C70
C80
Generic speed sensor shown

Parts Manual
Order code: FAC

Model/Kit
B83 87-02 140644 (9005110-5600) Plug assembly 1
C80 87-02 518929 Valve plate 1
E82 87-02 356576 (11062702) Spring 2
Order code: FAD

B83 87-02 140644 (9005110-5600) Plug assembly 1
C80 87-02 518806 Valve plate 1
E82 87-02 356576 (11062702) Spring 2

Parts Manual
S90 100cc pump special hardware FAL-FAU

Parts configuration
B83
QC04
C20
C30
C40
C05 E82
C50 E82
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067351 Slipper guide 1
on page 292 & SB-2009-038 on page 320)
on page 292)
on page 292)
Order code: FAL

B83 95-04 140644 (9005110-5600) Plug assembly 1
C80 95-04 518927 Valve plate 1
E82 95-04 356576 (11062702) Spring 2
Order code: FAN

B83 13-41 140644 (9005110-5600) Plug assembly 1
C80 13-41 518927 Valve plate 1
E82 13-41 356576 (11062702) Spring 2
Order code: FAP

B83 06-03 140644 (9005110-5600) Plug assembly 1
C80 06-03 518930 Valve plate, CW 1
E82 06-03 356576 (11062702) Spring 2
Order code: FAQ

B83 12-36 140644 (9005110-5600) Plug assembly 1
C80 12-36 518930 Valve plate 1
E82 12-36 356576 (11062702) Spring 2

Parts Manual
Parts configuration
B83
QC04
C20
C30
C40
C05 E82
C50 E82
*C70
C80

Parts Manual
Order code: FAR

Model/Kit
B83 95-39 140644 (9005110-5600) Plug assembly 1
C80 95-39 510720 Valve plate 1
E82 95-39 356576 (11062702) Spring 2
Order code: FAS

B83 97-03 140644 (9005110-5600) Plug assembly 1
C80 97-03 518929 Valve plate 1
E82 97-03 356576 (11062702) Spring 2
Order code: FAU

B83 98-38 140644 (9005110-5600) Plug assembly 1
C80 98-38 518806 Valve plate 1
E82 98-38 356576 (11062702) Spring 2

Parts Manual
S90 100cc pump special hardware FAW, FAZ, FAX

Parts configuration
W3CN
W1CN
B83
(FAW & FAZ)

B2CN
QC04
C20
C30
C40
C05 E82
C50 E82
*C70
C80
B83
(FAX)
QC04
C20
C30
C40
C05 E82
C50 E82
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067351 Slipper guide 1
on page 292 & SB-2009-038 on page 320)
on page 292)
on page 292)
Order code: FAW

B2CN 99-19 775312 Set screw 1
B83 99-19 140644 (9005110-5600) Plug assembly 1
C80 99-19 510720 Valve plate 1
E82 99-19 356576 (11062702) Spring 2
W1CN 99-19 723726 Connector 1
W3CN 99-19 574095 Cap 1
Order code: FAX

B83 01-07 140644 (9005110-5600) Plug assembly 1
C80 01-07 510720 Valve plate 1
E82 01-07 356576 (11062702) Spring 2
Order code: FAZ

B2CN 05-14 775312 Set screw 1
B83 05-14 140644 (9005110-5600) Plug assembly 1
C80 05-14 518929 Valve plate 1
E82 05-14 356576 (11062702) Spring 2
W3CN 05-14 574095 Cap 1

Parts Manual
S90 100cc pump special hardware FBA-GAA

Parts configuration
B84 (FBA, FBC, FHP & GAA)

B83
B83
(FBF)
*QB83 B10
QC04
C20
C30
C40
C05 E82
C50 E82
*C70
C80
(GAA)
B83
QC04
C20
C30
C40
C05
C50
*C70
C80

Parts Manual
Model/Kit
C30 87-02 11067351 Slipper guide 1
on page 292 & SB-2009-038 on page 320)
on page 292)
on page 292)
Order code: FBA

B83 06-12 140644 (9005110-5600) Plug assembly 1
C80 06-12 518929 Valve plate 1
E82 06-12 356576 (11062702) Spring 2
Order code: FBC

B83 06-12 140644 (9005110-5600) Plug assembly 1
C80 06-12 518806 Valve plate 1
E82 06-12 356576 (11062702) Spring 2
Order code: FBF

B83 06-12 8700127 Diagnostic receptacle 1
B84 06-12 8700128 Dust cover 1
C80 06-12 518929 Valve plate 1
E82 06-12 356576 (11062702) Spring 2
Order code: FHP

B10 12-39 11117130 Housing, special 1
B83 12-39 140644 (9005110-5600) Plug assembly 1
C80 12-39 518806 Valve plate 1
E82 12-39 356576 (11062702) Spring 2
Order code: GAA

B83 94-03 140644 (9005110-5600) Plug assembly 1
C80 94-03 349266 Valve plate 1

Parts Manual
S90 100cc pump special hardware GB1, GB4, GB8

Parts configuration
B83
G86
G85
G84
G76 QC04 C20
G74
G73 G75 C30
G88
C40
G72
C05
C50
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067351 Slipper guide 1
on page 292 & SB-2009-038 on page 320)
on page 292)
on page 292)
Order code: GB1

B83 02-30 140644 (9005110-5600) Plug assembly 1
C05 02-30 11033868 (11012434) Cylinder block assembly 1
C80 02-30 518806 Valve plate 1
G73 02-30 519873 Seal 1
G74 02-30 144725 (9004105-0110) O-ring 1
G75 02-30 518329 O-ring 1
G76 02-30 517828 Valve housing 1
G84 02-30 3103375-0175 SCR valve, 175 bar [2538 psi] 1
G85 02-30 4800780 Spring 1
G86 02-30 11126727 Plug assembly 1
G88 02-30 517829 Spring seat 1
G89 02-30 517831 Spring 1
Order code: GB4

B83 02-30 140644 (9005110-5600) Plug assembly 1
C80 02-30 518806 Valve plate 1
G73 02-30 519873 Seal 1
G74 02-30 144725 (9004105-0110) O-ring 1
G75 02-30 518329 O-ring 1
G85 02-30 4800780 Spring 1
G86 02-30 11126727 Plug assembly 1
G88 02-30 517829 Spring seat 1
G89 02-30 517831 Spring 1

Parts Manual
Parts configuration
B83
G86
G85
G84
G76 QC04 C20
G74
G73 G75 C30
G88
C40
G72
C05
C50
*C70
C80

Parts Manual
Order code: GB8

Model/Kit
B83 02-30 140644 (9005110-5600) Plug assembly 1
C05 02-30 11033868 (11012434) Cylinder block assembly 1
C80 02-30 518806 Valve plate 1
G73 02-30 519873 Seal 1
G74 02-30 144725 (9004105-0110) O-ring 1
G75 02-30 518329 O-ring 1
G85 02-30 4800780 Spring 1
G86 02-30 11126727 Plug assembly 1
G88 02-30 517829 Spring seat 1
G89 02-30 517831 Spring 1

Parts Manual
S90 100cc pump special hardware GBA-GBT

Parts configuration
B83
(GBA, GBE, GBK, GBP, GBS, GBT)
B2CN
QC04
C20
C30
C40
C05
C50
*C70
B83
C80
(GBQ)
G86
G85
G84
G76 QC04 C20
G74
G73 G75 C30
G88
C40
G72
C05
C50
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067351 Slipper guide 1
on page 292 & SB-2009-038 on page 320)
on page 292)
on page 292)
Order code: GBA

B83 87-02 140644 (9005110-5600) Plug assembly 1
C80 87-02 518806 Valve plate 1
Order code: GBE

B83 06-20 140644 (9005110-5600) Plug assembly 1
C80 06-20 518806 Valve plate 1
Order code: GBG

B2CN 95-16 042457 Set screw 1
B83 95-16 140644 (9005110-5600) Plug assembly 1
C80 95-16 518806 Valve plate 1
Order code: GBK

B83 95-16 140644 (9005110-5600) Plug assembly 1
C80 95-16 518806 Valve plate 1
Order code: GBP

B83 06-17 140644 (9005110-5600) Plug assembly 1
C80 06-17 518806 Valve plate 1
Parts continue to the next 2 pages.

Parts Manual
Parts configuration
B83
(GBA, GBE, GBK, GBP, GBS, GBT)
B2CN
QC04
C20
C30
C40
C05
C50
*C70
B83
C80
(GBQ)
G86
G85
G84
G76 QC04 C20
G74
G73 G75 C30
G88
C40
G72
C05
C50
*C70
C80

Parts Manual
Order code: GBQ

Model/Kit
B83 95-16 140644 (9005110-5600) Plug assembly 1
C80 95-16 518806 Valve plate 1
Order code: GBS

B83 97-05 140644 (9005110-5600) Plug assembly 1
C80 97-05 518806 Valve plate 1
Order code: GBT

B83 04-50 140644 (9005110-5600) Plug assembly 1
C80 04-50 518806 Valve plate 1

Parts Manual
S90 100cc pump special hardware GCA-GFJ

Parts configuration
B83
QC04
C20
C30
C40
C06
C50
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067351 Slipper guide 1
on page 292 & SB-2009-038 on page 320)
on page 292)
on page 292)
Order code: GCA

B83 98-14 140644 (9005110-5600) Plug assembly 1
C80 98-14 518929 Valve plate 1
Order code: GCP

B83 94-50 140644 (9005110-5600) Plug assembly 1
C80 94-50 518929 Valve plate 1
Order code: GCR

B83 11-23 140644 (9005110-5600) Plug assembly 1
C80 11-23 518806 Valve plate 1
Order code: GCS

B83 98-49 140644 (9005110-5600) Plug assembly 1
C80 98-49 518929 Valve plate 1
Order code: GDE

B83 98-49 140644 (9005110-5600) Plug assembly 1
C80 98-49 518806 Valve plate 1

Parts Manual
Parts configuration
B83
QC04
C20
C30
C40
C06
C50
*C70
C80

Parts Manual
Order code: GFD

Model/Kit
B83 06-12 140644 (9005110-5600) Plug assembly 1
C80 06-12 518806 Valve plate 1
Order code: GFH

B83 06-12 140644 (9005110-5600) Plug assembly 1
C80 06-12 518806 Valve plate 1
Order code: GFJ

B83 06-14 140644 (9005110-5600) Plug assembly 1
C80 06-14 518806 Valve plate 1

Parts Manual
S90 100cc pump special hardware GFK-GTA

Parts configuration
B83
(GFK., GHT, GLA & GTA)
QC04
C20
C30
C40
C06
C50
*C70
C80
B83
(GP4)
G86
G85
G84
G76 QC04 C20
G74
G73 G75 C30
G88 C40
G72
C05
C50
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067351 Slipper guide 1
on page 292 & SB-2009-038 on page 320)
on page 292)
on page 292)
Order code: GFK

B83 06-12 140644 (9005110-5600) Plug assembly 1
C80 06-12 518806 Valve plate 1
Order code: GHT

B10 12-39 11117130 Housing, special 1
B83 12-39 140644 (9005110-5600) Plug assembly 1
C80 12-39 518929 Valve plate 1
Order code: GLA

B83 07-49 140644 (9005110-5600) Plug assembly 1
C80 07-49 518930 Valve plate, CW 1
Order code: GLS

B83 07-49 140644 (9005110-5600) Plug assembly 1
C80 07-49 518930 Valve plate, CW 1

Parts Manual
Parts configuration
B83
(GFK., GHT, GLA & GTA)
QC04
C20
C30
C40
C06
C50
*C70
C80
B83
(GP4)
G86
G85
G84
G76 QC04 C20
G74
G73 G75 C30
G88 C40
G72
C05
C50
*C70
C80

Parts Manual
Order code: GP4

Model/Kit
B83 09-30 140644 (9005110-5600) Plug assembly 1
C80 09-30 518930 Valve plate 1
G73 09-30 519873 Seal 1
G74 09-30 144725 (9004105-0110) O-ring 1
G75 09-30 518329 O-ring 1
G85 09-30 4800780 Spring 1
G86 09-30 11126727 Plug assembly 1
G88 09-30 517829 Spring seat 1
G89 09-30 517831 Spring 1
Order code: GTA

B83 14-02 140644 (9005110-5600) Plug assembly 1
C80 14-02 518806 Valve plate 1

Parts Manual
S90 100cc pump special hardware GTB-JCB

Parts configuration
(HBA) W3CN
W1CN
B83
B2CN
QC04
C20
C30
C40
C05
C50
*C70
C80
(GTB, JAA, JCA & JCB)
B83
QC04
C20
C30
C40
C06
C50
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067351 Slipper guide 1
on page 292 & SB-2009-038 on page 320)
on page 292)
on page 292)
Order code: GTB

B83 15-41 140644 (9005110-5600) Plug assembly 1
C80 15-41 518806 Valve plate 1
Order code: HBA

B2CN 94-14 775312 Set screw 1
B83 94-14 140644 Plug assembly 1
C80 94-14 518994 Valve plate 1
W3CN 94-14 574095 Cap 1
Order code: JAA

B83 94-13 140644 (9005110-5600) Plug assembly 1
C80 94-13 518994 Valve plate 1
Order code: JCA

B83 08-12 140644 (9005110-5600) Plug assembly 1
C80 08-12 518806 Valve plate 1
Order code: JCB

B83 09-13 140644 (9005110-5600) Plug assembly 1
C80 09-13 518806 Valve plate 1

Parts Manual
S90 100cc pump special hardware JCC-PEB

Parts configuration
B83
(JCC)
G86
G85
G84
G76 QC04 C20
G74
G73 G75 C30
G88 C40
G72
C05
C50
*C70
C80
(JCF & KCA)
B83
(PEA & PEB)
*QB83
B83
QC04
C20
C30
C40
C06 E82
C50 E82
*C70
C80
Generic speed sensor shown.

Parts Manual
Common parts
Model/Kit
C30 87-02 11067351 Slipper guide 1
on page 292 & SB-2009-038 on page 320)
on page 292)
on page 292)
Order code: JCC

B83 09-13 140644 (9005110-5600) Plug assembly 1
C80 09-13 518806 Valve plate 1
G73 09-13 519873 Seal 1
G74 09-13 144725 (9004105-0110) O-ring 1
G75 09-13 518329 O-ring 1
G85 09-13 4800780 Spring 1
G86 09-13 11126727 Plug assembly 1
G88 09-13 517829 Spring seat 1
G89 09-13 517831 Spring 1
Order code: JCF

B83 10-15 140644 (9005110-5600) Plug assembly 1
C80 10-15 518929 Valve plate 1
E82 10-15 356576 (11062702) Spring 2
Order code: KCA

B83 94-29 140644 (9005110-5600) Plug assembly 1
C80 94-29 518994 Valve plate 1

Parts Manual
Parts configuration
B83
(JCC)
G86
G85
G84
G76 QC04 C20
G74
G73 G75 C30
G88 C40
G72
C05
C50
*C70
C80
(JCF & KCA)
B83
(PEA & PEB)
*QB83
B83
QC04
C20
C30
C40
C06 E82
C50 E82
*C70
C80
Generic speed sensor shown.

Parts Manual
Order code: PEA

Model/Kit
C06 07-04 11093925 Cylinder block assembly, with speed ring 1
C80 07-04 518806 Valve plate 1
QB83 07-04 085043 (9004201-3700) O-ring 1
Order code: PEB

C05 08-32 11093925 Cylinder block assembly, with speed ring 1
C80 08-32 518931 Valve plate 1
QB83 07-04 085043 (9004201-3700) O-ring 1

Parts Manual
S90 100cc pump special hardware PGA, PGB

Parts configuration
B83
QC04
C20
C30
C40
C06
C50
*C70
C80

Parts Manual
Common parts
Item Date Begin Date End Part Name Part Number Qty. per
Model/Kit
C30 87-02 11067351 Slipper guide 1
on page 292 & SB-2009-038 on page 320)
on page 292)
on page 292)
Order code: PGA

B83 08-32 140644 (9005110-5600) Plug assembly 1
C80 08-32 518806 Valve plate 1
Order code: PGB

B83 08-32 140644 (9005110-5600) Plug assembly 1

Parts Manual
S90 100cc pump displacement limitation 2-4

Parts configuration
F113
F105
*F112
(4)
F111
(2 & 3)
F105
(*F40)
(*F50)
F111
(*F40)
(*F50)
(*F12)
F10
(*F11)
(*F11)
(*F12)
F205
(*F50)
(*F40)
F205
F211
(*F50)
(*F40) (3)
F213
*F212
F211
(2 & 4)
() Not available for individually

Parts Manual
Order code: 2
Model/Kit
F10 00-02 11044943 Servo piston assembly (SB-2000-022 on page 304 1
& SB-2009-035 on page 319)
F105 00-02 11060703 (11055769) Servo cylinder assembly 1
F111 00-02 378083 (9007210-0804) Screw 3
F211 00-02 378083 (9007210-0804) Screw 3
F212 00-02 505412 (9003509-0008) Seal nut 1
F213 00-02 5000747 Set screw (SB-2000-022 on page 304) 1
Order code: 3
& SB-2009-035 on page 319)
F111 87-02 378083 (9007210-0804) Screw 3
F211 87-02 378083 (9007210-0804) Screw 3
Order code: 4
& SB-2009-035 on page 319)
F111 87-02 378083 (9007210-0804) Screw 3
F112 87-02 505412 (9003509-0008) Seal nut 1
F113 87-02 5000747 Setscrew (SB-2000-022 on page 304) 1
F211 87-02 378083 (9007210-0804) Screw 3
F212 87-02 505412 (9003509-0008) Seal nut 1

Parts Manual
S90 100cc pump displacement limitation 7

Parts configuration
F111
*F124
F022
F021
F020
F019 F105
(*F40)
F018 (*F50)
F016
F023
F015
F017
(*F12) F10
(*F11)
(*F11)
(*F12)
F100
F205
(*F50)
(*F40)
F211
() Not available individually

Parts Manual
Order code: 7
Model/Kit
F10 98-14 11044946 Servo piston assembly 1
F015 98-14 346031 Screw 1
F016 98-14 507096 Spring guide 1
F017 98-14 345967 Servo spring housing 1
F018 98-14 351742 Spring 1
F019 98-14 507094 Spring guide 1
F020 98-14 505826 Retaining ring 1
F021 98-14 507045 Castle nut 1
F022 98-14 346015 Nut 1
F023 98-14 11140221 Adjusting screw 1
F100 98-14 515327 (8200532) Servo assembly 1
F105 98-14 11059762 (11055776) Servo cylinder assembly, automotive control 1
F111 98-14 746651 (393595) Screw 3
F124 98-14 066159 Seal nut 1
F211 98-14 378083 (9007210-0804) Screw 3

Parts Manual
S90 100cc pump displacement limitation 8, B

Parts configuration
F113 F105
*F112
(8)
F111
F111 (*F40)
(*F50)
(*F40)
F105
(*F50)
(B)
(*F12)
(*F11) F10
(*F11)
(*F12)
F200
F017
F015
F023
F016
F018
F019
F205 F021
F020
F022
(*F50)
(*F40)
*F224
F211

Parts Manual
Order code: 8
Model/Kit
F10 90-07 15-03 11044946 Servo piston assembly 1
F015 90-07 15-03 346031 Screw 1
F016 90-07 15-03 507096 Spring guide 1
F017 90-07 15-03 345967 Servo spring housing 1
F018 90-07 15-03 351742 Spring 1
F019 90-07 15-03 507094 Spring guide 1
F020 90-07 15-03 505826 Retaining ring 1
F021 90-07 15-03 507045 Castle nut 1
F022 90-07 15-03 346015 Nut 1
F023 90-07 15-03 11140221 Adjusting screw 1
F105 90-07 15-03 11060704 (11055771) Servo cylinder assembly 1
F111 90-07 15-03 378083 (9007210-0804) Screw 3
F112 90-07 15-03 505412 (9003509-0008) Seal nut 1
F113 90-07 15-03 5000747 Set screw, M8 x 45mm, (SB-2000-022 on page 1
304)
F200 90-07 15-03 515327 (8200532) Servo assembly 1
F205 90-07 15-03 11059762 (11055776) Servo cylinder assembly 1
F211 90-07 15-03 746651 (393595) Screw 3
F224 90-07 15-03 066159 Seal nut 1
Order code: B
F015 98-14 346031 Screw 1
F016 98-14 507096 Spring guide 1
F018 98-14 351742 Spring 1
F019 98-14 507094 Spring guide 1
F021 98-14 507045 Castle nut 1
F022 98-14 346015 Nut 1
F111 98-14 378083 (9007210-0804) Screw 3
F200 98-14 515327 (8200532) Servo assembly 1
F211 98-14 746651 (393595) Screw 3
F224 98-14 066159 Seal nut 1

Parts Manual
S90 100cc pump displacement limitation D

Parts configuration
F111
*F124
F022
F021
F020
F019 F105
(*F40)
F018 (*F50)
F016
F023
F015
F017
(*F12)
F10
(*F11)
(*F11)
(*F12)
F100
F205
(*F50)
(*F40)
F213
F211
*F212

Parts Manual
Order code: D
Model/Kit
F015 98-18 346031 Screw 1
F016 98-18 507096 Spring guide 1
F018 98-18 351742 Spring 1
F019 98-18 507094 Spring guide 1
F021 98-18 507045 Castle nut 1
F022 98-18 346015 Nut 1
F100 98-18 515327 (8200532) Servo assembly 1
F105 98-18 11059762 Servo cylinder assembly, automotive control 1
F111 98-18 378083 Screw 3
F124 98-18 066159 Seal nut 1
F205 98-18 11060704 Servo cylinder assembly 1
F211 98-18 746651 Screw 3
F212 98-18 505412 (9003509-0008) Seal nut 1

Parts Manual
S90 100cc pump displacement limitation E, F

Parts configuration
*F112 F125
F113
F105
F111
(E)
F105
(*F40)
(*F50)
F111
(*F40)
(F) (*F50)
(*F12)
F10
(*F11)
(*F11)
(*F12)
(F)
F205
(*F50)
(*F40)
F205 F225
F211
(*F50)
(*F40)
F213
(E)
F211
*F212

Parts Manual
Order code: E
Model/Kit
F10 97-44 511613 Servo piston assembly (SB-2000-022 on page 1
304)
F111 97-44 746651 Screw 3
F112 97-44 336826 (9003508-0010) Seal nut 1
F113 97-44 733691 Set screw 1
F125 97-44 091033 Plug assembly 1
F211 97-44 746651 (9007210-0804) Screw 3
F212 97-44 336826 (9003508-0010) Seal nut 1
F213 97-44 733691 Set screw 1
F225 97-44 091033 Plug assembly 1
Order code: F
304)
F111 91-30 378083 (9007210-0804) Screw 3
F211 91-30 378083 (9007210-0804) Screw 3

Parts Manual
S90 100cc pump displacement limitation H

Parts configuration
F113 F105
*F112
F111
(*F40)
(*F50)
(*F12)
F10
(*F11)
(*F11)
(*F12)
F200
F017
F015
F023
F016
F018
F019
F205 F021
F020
F022
(*F50)
(*F40)
*F224
F211

Parts Manual
Order code: H
Item Date Begin Date Begin Part Number Part Name Qty. per
Model/Kit
F015 98-18 346031 Screw 1
F016 98-18 507096 Spring guide 1
F018 98-18 351742 Spring 1
F019 98-18 507094 Spring guide 1
F021 98-18 507045 Castle nut 1
F022 98-18 346015 Nut 1
F111 98-18 746651 Screw 3
F112 98-18 505412 (9003509-0008) Seal nut 1
F113 98-18 5000747 Set screw, M8 x 45mm, (SB-2000-022 on page 1
304)
F200 98-18 515327 (8200532) Servo assembly 1
F211 98-18 378083 (9007210-0804) Screw 3
F224 98-18 066159 Seal nut 1

Parts Manual
S90 100cc pump displacement limitation P

Parts configuration
F113
F105
*F112
F111
(*F40)
(*F50)
(*F12)
F10
(*F11)
(*F11)
(*F12)
F205
(*F50)
(*F40)
F213
*F212
F211

Parts Manual
Order code: P
Model/Kit
319)
F111 03-16 378083 (9007210-0804) Screw 3
F112 03-16 505412 (9003509-0008) Seal nut 1
F113 03-16 11001516 Set screw 1
F211 03-16 378083 (9007210-0804) Screw 3
F212 03-16 505412 (9003509-0008) Seal nut 1
F213 03-16 11001516 Set screw 1

Parts Manual
End cap
S90 100cc pump end cap H, 2, 6-65

Parts configuration
*G30
G53
G54
G96
(deleted
G90 G20 95-06)
G93 G18
G94
G95
G51
G97
G50
G17
G40
G04 G48
G52
G49

Parts Manual
End cap
Common parts
Model/Kit
G17 92-12 327007 (9005110-4400) Plug (SB-1992-003 on page 270) 1
G18 92-12 327007 (9005110-4400) Plug (SB-1992-003 on page 270) 1
G20 87-02 673319 (8700030) Journal bearing 1
G30 89-46 8200212 End cap gasket (SB-1992-003 on page 270) 1
G30 87-02 89-45 8200043 End cap gasket (SB-1989-023 on page 268) 1
G40 87-02 8700008 Bushing 1
G48 87-02 046151 (9005100-5600) Plug assembly 1
G49 87-02 046151 (9005100-5600) Plug assembly 1
G50 87-02 046151 (9005100-5600) Plug assembly 1
G51 87-02 140644 (9005110-5600) Plug assembly 1
G52 87-02 140644 (9005110-5600) Plug assembly 1
G53 87-02 140644 (9005110-5600) Plug assembly 1
G54 87-02 140644 (9005110-5600) Plug assembly 1
G90 92-12 746644 (9007314-0810) Screw 1
G90 89-46 92-11 694356 (9007314-0608) Screw (SB-1992-003 on page 270) 1
G90 87-02 89-45 331447 (9007314-0607) Screw 1
G93 92-12 713800 (8800564) Spacer 1
G93 87-02 92-11 307678 (8800404) Spacer 1
G94 92-12 8800565 Lifting bracket 1
G94 87-02 92-11 8800522 Lifting bracket 1
G95 92-12 002311 (9009610-3459) Washer 1
G95 87-02 92-11 502195 Washer 1
G96 92-12 95-06 9007314-0808 Screw (SB-1994-035 on page 281) 1
G96 87-02 92-11 331447 (9007314-0607) Screw (SB-1992-003 on page 270) 1
G97 92-12 746644 (9007314-0810) Screw 1
G97 87-02 92-11 694356 (9007314-0608) Screw (SB-1992-003 on page 270) 1
Order codes: 2, 6, 60, 61

G04 92-12 8200236 End cap assembly, side ports (SB-1992-003 on 1
page 270)
Order codes: H, 62
G04 94-29 8200294 End cap assembly, metric side ports 1
Order code: 65
Order code: 6P
G04 98-13 8200388 End cap assembly, side ports, CW 1

Parts Manual
End cap
S90 100cc pump end cap 60, 62, 67

Parts configuration
*G30
G53
G54
G96
G90 G20
G93
G94
G95 G57
G97
G51
G17
G40
G04 G48
G49
G52

Parts Manual
End cap
Common parts
Model/Kit
G17 94-24 140644 Plug assembly 1
G30 94-24 8200212 End cap gasket 1
G40 94-24 664771 Bushing 1
G51 94-24 327007 (9005110-4400) Plug assembly 1
G90 94-24 746644 (9007314-0810) Screw 1
G93 94-24 713800 (8800564) Spacer 1
G95 94-24 502195 Washer 1
G96 94-24 746594 (9007314-0807) Screw 1
G97 94-24 746644 (9007314-0810) Screw 1
Order code: 60
G04 94-24 505048 End cap assembly, side ports 1
Order code: 62
Order code: 67
G04 96-03 505052/P End cap assembly, metric side ports 1

Parts Manual
End cap
S90 100cc pump end cap 1, 8, 8G, M, 80-82

Parts configuration
(1, 8, M, 80, 81, 82)
*G30
G53
G45
G54
G96
(deleted
G90 G20 95-06)
G93 G18
G94
G51
G95
G97
G40
G04
G52
G47
(8G)
G46
*G30
G53
G45
G54
G96
(deleted
G90 G20 95-06)
G93 G18
G94
G51
G95
G97
G40
G04
G52
G46

Parts Manual
End cap
Common parts
Model/Kit
G30 87-02 8200212 End cap gasket 1
G40 87-02 664771 (8700008) Bushing 1
G46 87-02 046151 (9005100-5600) Plug assembly 1
G90 87-02 746644 (9007314-0810) Screw 1
G93 87-02 713800 (8800564) Spacer 1
G95 87-02 502195 Washer 1
G97 87-02 746644 (9007314-0810) Screw 1
Order codes: 1, 8, 80, 81

G04 92-12 8200235 End cap assembly 1
G45 87-02 046151 (9005100-5600) Plug assembly 1
G47 87-02 046151 (9005100-5600) Plug assembly 1
G51 87-02 140644 (9005110-5600) Plug assembly 1
G52 87-02 140644 (9005110-5600) Plug assembly 1
G53 87-02 140644 (9005110-5600) Plug assembly 1
G54 87-02 140644 (9005110-5600) Plug assembly 1
Order codes: M, 82
G04 94-15 8200430 End cap assembly, metric ports 1
G45 87-02 046151 (9005100-5600) Plug assembly 1
G47 87-02 046151 (9005100-5600) Plug assembly 1
G51 87-02 140644 (9005110-5600) Plug assembly 1
G52 87-02 140644 (9005110-5600) Plug assembly 1
G53 87-02 140644 (9005110-5600) Plug assembly 1
G54 87-02 140644 (9005110-5600) Plug assembly 1
Order code: 8G
G04 94-15 8200346 End cap assembly, no charge pump 1
G45 87-02 046151 (9005100-5600) Plug assembly 1
G51 87-02 140644 (9005110-5600) Plug assembly 1
G52 87-02 140644 (9005110-5600) Plug assembly 1
G53 87-02 140644 (9005110-5600) Plug assembly 1
G54 87-02 140644 (9005110-5600) Plug assembly 1

Parts Manual
End cap
S90 100cc pump end cap 8M, 8W

Parts configuration
(8M)
*G30
G87
G53
G54 G45
G90 G20
G93
G94
G51
G95
G97
G40
G04
G52
G47
G46
*G30
(8W)
G45
G90 G20
G93
G94
G95
G97
G40
G04
G47
G46

Parts Manual
End cap
Order code: 8M
Model/Kit
G30 97-26 8200212 End cap gasket 1
G40 97-26 664771 (8700008) Bushing 1
G45 97-26 8700127 Diagnostic receptacle 1
G46 97-26 046151 (9005100-5600) Plug assembly 1
G47 97-26 046151 (9005100-5600) Plug assembly 1
G51 97-26 140644 (9005110-5600) Plug assembly 1
G52 97-26 140644 (9005110-5600) Plug assembly 1
G53 97-26 140644 (9005110-5600) Plug assembly 1
G54 97-26 140644 (9005110-5600) Plug assembly 1
G87 97-26 8700128 Dust cover 1
G90 97-26 746644 (9007314-0810) Screw 1
G93 97-26 713800 (8800564) Spacer 1
G95 97-26 002311 (9009610-3459) Washer 1
G97 97-26 746644 (9007314-0810) Screw 1
Order code: 8W
G04 03-35 8200541 End cap assembly, CW 1
G30 03-35 8200212 End cap gasket 1
G40 03-35 664771 (8700008) Bushing 1
G45 03-35 046151 (9005100-5600) Plug assembly 1
G46 03-35 046151 (9005100-5600) Plug assembly 1
G47 03-35 046151 (9005100-5600) Plug assembly 1
G90 03-35 746644 (9007314-0810) Screw 1
G93 03-35 713800 (8800564) Spacer 1
G95 03-35 002311 (9009610-3459) Washer 1
G97 03-35 746644 (9007314-0810) Screw 1

Parts Manual
End cap
S90 100cc pump end cap 80, 8C

Parts configuration
*G30
(80)
G53
G54 G45
G90
G20
G93
G94
G51
G95
G97
G40
G04
G52
G47
G46
(8C) *G30
G11
G53
G54
G45
G14
G19
G114
G20
G90
G55
G93
G94
G95
G97
G40
G04
G47
G46

Parts Manual
End cap
Common parts
Model/Kit
G30 87-02 8200212 End cap gasket 1
G40 87-02 664771 (8700008) Bushing 1
G90 87-02 746644 (9007314-0810) Screw 1
G93 87-02 713800 (8800564) Spacer 1
G95 87-02 002311 (9009610-3459) Washer 1
G97 87-02 746644 (9007314-0810) Screw 1
Order code: 80
Order code: 8C
G04 94-15 14-41 508814 End cap assembly 1
G11 87-02 14-41 140644 Plug assembly 1
G45 87-02 14-41 140644 Plug assembly 1
G46 87-02 14-41 140644 Plug assembly 1
G47 87-02 14-41 140644 Plug assembly 1
G53 87-02 14-41 327007 (9005110-4400) Plug assembly 1
G54 87-02 14-41 327007 (9005110-4400) Plug assembly 1
G55 87-02 14-41 327007 (9005110-4400) Plug assembly 1
G114 87-02 14-41 327007 (9005110-4400) Plug assembly 1

Parts Manual
End cap
S90 100cc pump end cap 8P, 8S

Parts configuration
G81
G80 G83
G82
G78
(8P) G77
*G30
G79
G04
G54
G24
G27
G90 G20
G93 G51
G12
G94 G25
G95 G81
G97 G80 G83
G82
G40
G22
G46
G47
G78
G77
*G30
(8S)
G04 G79
G54
G53
G29 G24
G27
G90 G20
G93 G51
G12
G94 G25
G95
G97
G40
G22
G46
G47

Parts Manual
End cap
Common parts
Model/Kit
G30 08-09 8200212 End cap gasket 1
G40 08-09 664771 (8700008) Bushing 1
G93 08-09 713800 (8800564) Spacer 1
G95 08-09 002311 (9009610-3459) Washer 1
Order code: 8P
G04 08-09 11034378 End cap assembly, CCW 1
G12 08-09 11040532 Plug assembly 1
G22 08-09 046151 (9005100-5600) Plug assembly 1
G24 08-09 11040532 Plug assembly 1
G25 08-09 11040532 Plug assembly 1
G27 08-09 11040532 Plug assembly 1
G46 08-09 046151 (9005100-5600) Plug assembly 1
G47 08-09 046151 (9005100-5600) Plug assembly 1
G51 08-09 11040532 Plug assembly 1
G54 08-09 11040532 Plug assembly 1
G77 08-09 517830 Valve spool 1
G78 08-09 517832 Spring 1
G79 08-09 11034287 Valve spool 1
G80 08-09 504681 Screw 1
G81 08-09 504681 Screw 1
G82 08-09 504681 Screw 1
G83 08-09 504681 Screw 1
G90 08-09 9007314-0812 Screw 1
G97 08-09 506969 Screw 1

Parts Manual
End cap
Parts configuration
G81
G80 G83
G82
G78
(8P) G77
*G30
G79
G04
G54
G24
G27
G90 G20
G93 G51
G12
G94 G25
G95 G81
G97 G80 G83
G82
G40
G22
G46
G47
G78
G77
*G30
(8S)
G04 G79
G54
G53
G29 G24
G27
G90 G20
G93 G51
G12
G94 G25
G95
G97
G40
G22
G46
G47

Parts Manual
End cap
Order code: 8S
Model/Kit
G12 09-30 11040532 Plug assembly 1
G22 09-30 046151 (9005100-5600) Plug assembly 1
G24 09-30 11040532 Plug assembly 1
G25 09-30 11040532 Plug assembly 1
G27 09-30 11040532 Plug assembly 1
G29 09-30 327007 (9005110-4400) Plug assembly 1
G46 09-30 046151 (9005100-5600) Plug assembly 1
G47 09-30 046151 (9005100-5600) Plug assembly 1
G51 09-30 11040532 Plug assembly 1
G53 09-30 11040532 Plug assembly 1
G54 09-30 11040532 Plug assembly 1
G77 09-30 517830 Valve spool 1
G78 09-30 517832 Spring 1
G79 09-30 11068446 Valve spool 1
G80 09-30 504681 Screw 1
G81 09-30 504681 Screw 1
G82 09-30 504681 Screw 1
G83 09-30 504681 Screw 1
G90 09-30 9007314-0812 Screw 1
G97 09-30 506969 Screw 1

Parts Manual
End cap
S90 100cc pump end cap 8E, 8F

Parts configuration
G81
G80 G83
G82
G78 (8E)
G77
*G30
G79
G04
G54
G24
G27
G90 G20
G93 G12 G51

G94 G25
G95 G81
G80 G83
G97 G82
G40
G22
G46
G47
G78
(8F)
G77
*G30
G04 G79
G54
G53
G29 G24
G27
G90 G20
G93 G51
G12
G94 G25 G66
G95
G70A
G97
G40
G22
G46
G47

Parts Manual
End cap
Common parts
Model/Kit
G30 02-30 8200212 End cap gasket 1
G40 02-30 664771 (8700008) Bushing 1
G93 02-30 713800 (8800564) Spacer 1
G95 02-30 502195 Washer 1
Order code: 8E
G12 02-30 11040532 Plug assembly 1
G24 02-30 11040532 Plug assembly 1
G25 02-30 11040532 Plug assembly 1
G27 02-30 11040532 Plug assembly 1
G51 02-30 11040532 Plug assembly 1
G54 02-30 11040532 Plug assembly 1
G77 02-30 517830 Valve spool 1
G78 02-30 517832 Spring 1
G79 02-30 517827 Valve spool 1
G80 02-30 504681 Screw 1
G81 02-30 504681 Screw 1
G82 02-30 504681 Screw 1
G83 02-30 504681 Screw 1
G90 02-30 713768 Screw 1
G97 02-30 506969 Screw 1

Parts Manual
End cap
Parts configuration
G81
G80 G83
G82
G78 (8E)
G77
*G30
G79
G04
G54
G24
G27
G90 G20
G93 G12 G51

G94 G25
G95 G81
G80 G83
G97 G82
G40
G22
G46
G47
G78
(8F)
G77
*G30
G04 G79
G54
G53
G29 G24
G27
G90 G20
G93 G51
G12
G94 G25 G66
G95
G70A
G97
G40
G22
G46
G47

Parts Manual
End cap
Order code: 8F
Model/Kit
G12 02-30 11040532 Plug assembly 1
G24 02-30 11040532 Plug assembly 1
G25 02-30 11040532 Plug assembly 1
G27 02-30 11040532 Plug assembly 1
G29 02-30 327007 (9005110-4400) Plug assembly 1
G51 02-30 11040532 Plug assembly 1
G53 02-30 11040532 Plug assembly 1
G54 02-30 11040532 Plug assembly 1
G66 02-30 521318 Reducer assembly 1
G70A 02-30 093823 O-ring 1
G77 02-30 517830 Valve spool 1
G78 02-30 517832 Spring 1
G79 02-30 517827 Valve spool 1
G80 02-30 504681 Screw 1
G81 02-30 504681 Screw 1
G82 02-30 504681 Screw 1
G83 02-30 504681 Screw 1
G90 02-30 713768 Screw 1
G97 02-30 506969 Screw 1

Parts Manual
End cap
S90 100cc pump end cap 8K, 8N

Parts configuration
G81
G80 G83
G82
G78
G77
*G30
G04 G79
G54
G53
G29 G24
G27
G90 G20
G93 G51
G12
G94 G25
G95
G97
G40
G22
G46
G47

Parts Manual
End cap
Common parts
Model/Kit
G30 07-45 8200212 End cap gasket 1
G40 07-45 664771 (8700008) Bushing 1
G93 07-45 713800 (8800564) Spacer 1
G95 07-45 502195 Washer 1
Order code: 8K
G12 07-45 11040532 Plug assembly 1
G24 07-45 11040532 Plug assembly 1
G25 07-45 11040532 Plug assembly 1
G27 07-45 11040532 Plug assembly 1
G29 07-45 327007 (9005110-4400) Plug assembly 1
G51 07-45 11040532 Plug assembly 1
G53 07-45 11040532 Plug assembly 1
G54 07-45 11040532 Plug assembly 1
G77 07-45 517830 Valve spool 1
G78 07-45 517832 Spring 1
G79 07-45 517827 Valve spool 1
G80 07-45 504681 Screw 1
G81 07-45 504681 Screw 1
G82 07-45 504681 Screw 1
G83 07-45 504681 Screw 1
G90 07-45 713768 Screw 1
G97 07-45 506969 Screw 1

Parts Manual
End cap
Parts configuration
G81
G80 G83
G82
G78
G77
*G30
G04 G79
G54
G53
G29 G24
G27
G90 G20
G93 G51
G12
G94 G25
G95
G97
G40
G22
G46
G47

Parts Manual
End cap
Order code: 8N
Model/Kit
G12 10-40 11040532 Plug assembly 1
G24 10-40 11040532 Plug assembly 1
G25 10-40 11040532 Plug assembly 1
G27 10-40 11040532 Plug assembly 1
G29 10-40 327007 (9005110-4400) Plug assembly 1
G51 10-40 11040532 Plug assembly 1
G53 10-40 11040532 Plug assembly 1
G54 10-40 11040532 Plug assembly 1
G77 10-40 517830 Valve spool 1
G78 10-40 517832 Spring 1
G79 10-40 517827 Valve spool 1
G80 10-40 504681 Screw 1
G81 10-40 504681 Screw 1
G82 10-40 504681 Screw 1
G83 10-40 504681 Screw 1
G90 10-40 713768 Screw 1
G97 10-40 506969 Screw 1

Parts Manual
Charging system
S90 100cc pump charging system 3, D-L

Parts configuration
(L)
J40
H25 H90
H40 H50
(Germany only) (L)
H90
H25
H70
H80 H60
(3) H50
H40
H05
H60
H50
H70 H40
H80
(L)
H05
H80
(G) H70
H80
(D, E, F)

Parts Manual
Charging system
Order code: 3
Model/Kit
H25 01-29 517683 Spacer 1
H70 01-29 516761 Retaining plate 1
H80 01-29 648451 Screw 6
H90 01-29 676734 (9005110-9500) Plug assembly 1
J40 01-29 680892 O-ring 1
Order code: D
H05 93-15 8200238 Charge pump set, 17 cc (SB-1993-001 on page 1
273*)
H40 87-02 9004800-1224 Pin 1
H50 93-15 8801178 Charge pump shaft (SB-1993-001 on page 273* & 1
SB-1998-066 on page 294)
H50 87-02 89-16 8100142 Charge pump shaft (SB-1989-006 on page 266) 1
H60 87-02 9003310-1208 Key 1
H80 87-02 648451 (9007210-0604) Screw 6
* For information regarding replacement parts for units built from 89-17 to 93-14, refer to AN152886483362 in the appendix.
Order code: E
273*)
H40 87-02 9004800-1224 Pin 1
H50 93-15 8801178 Charge pump shaft (SB-1993-001 on page 273 & 1
SB-1998-066 on page 294)
H60 87-02 9003310-1208 Key 1
H80 87-02 648451 (9007210-0604) Screw 6
Order code: F
273*)
H40 87-02 9004800-1224 Pin 1
SB-1998-066 on page 294)
H60 87-02 9003310-1208 Key 1
H80 87-02 648451 (9007210-0604) Screw 6

Parts Manual
Charging system
Parts configuration
(L)
J40
H25 H90
H40 H50
(Germany only) (L)
H90
H25
H70
H80 H60
(3) H50
H40
H05
H60
H50
H70 H40
H80
(L)
H05
H80
(G) H70
H80
(D, E, F)

Parts Manual
Charging system
Order code: G
Model/Kit
H05 01-20 8200479 Charge pump set 1
H05 94-27 01-19 8200245 Charge pump set, 31 cc (SB-2001-013 on page 1
307)
H40 94-27 5000358 Pin 1
H50 01-20 8801210 Charge pump shaft 1
H50 94-27 01-19 8801179 Charge pump shaft (SB-1998-066 on page 294 & 1
SB-2001-013 on page 307)
H60 94-27 9003310-1208 Key 1
H80 01-20 041160 (9007314-0605) Screw 6
H80 94-27 01-19 9007210-0604 Screw (SB-2001-013 on page 307) 6
Order code: L
H25 87-02 326538 (8800466-0100) Charge pump spacer 1
H40 87-02 9004800-1224 Pin (Germany only) 1
SB-1998-066 on page 294)
H80 87-02 9007210-0604 Screw 6
H90 87-02 676734 (9005110-9500) Plug assembly 1

Parts Manual
Charging system
S90 100cc pump charging system M-X

Parts configuration
(M, N & S)
H25
H90
H70
H40
H25
H90
H80
(M) (M, N & S)

H50
J40
H25
H70 H60
(N) H80
H50
H40
H05
H70
(S) H80
H70
H80
(X)

Parts Manual
Charging system
Order code: M
Model/Kit
H25 96-05 8800973 Charge pump spacer 1
H80 96-05 9007210-0604 Screw 6
H90 96-05 676734 (9005110-9500) Plug assembly 1
Order code: N
H25 01-29 11077718 Spacer 1
H40 01-29 9004800-1224 Pin 1
H80 01-29 648451 Screw 6
H90 01-29 676734 (9005110-9500) Plug assembly 1
Order code: S
H25 96-24 509242 Charge pump spacer 1
H50 96-24 509221 Spacer 1
H80 96-24 648451 Screw 6
H90 96-24 676734 (9005110-9500) Plug assembly 1
J40 96-24 680892 (9004104-0440) O-ring 1
Order code: X
H05 04-42 8200239 Charge pump set, 20 cc 1
H40 04-42 9004800-1224 Pin 1
H50 04-42 8801178 Charge pump shaft 1
H60 04-42 9003310-1208 Key 1
H80 04-42 648451 Screw 6

Parts Manual
Auxiliary mounting
S90 pump aux mounting AB and AC

Parts configuration
J15
J30 J10
Design prior to 07-44 *J40

(used prior to 92-30)
J60
J70
J80
*J50
J90
J92
J95
J10
J15
J30
Design after 07-43
J60
J80
*J50
J90
J92
J95

Parts Manual
Auxiliary mounting
Order code: AB & A

Model/Kit
J10 87-02 8100147 Coupling, 9 tooth 1
J15 87-02 8800832 Cover assembly, CW (SB-1993-001 on page 273* 1
& SB-2005-011 on page 310)
J15 87-02 8800833 Cover assembly, CCW (SB-1993-001 on page 273* 1
& SB-2005-011 on page 310
J30 87-02 664771 (8700008) Bushing 1
J40 87-02 92-29 680892 (9004104-0440) O-ring 1
J50 87-02 056739 (9004104-1580) O-ring 1
J60 87-02 8200467 Flange adapter, SAE A (SB-2007-027 on page 313) 1
J70 87-02 07-43 664920 (9009625-0132) Washer (SB-2007-027 on page 313) 4
J80 98-44 518721 Screw, M16 x 140 4
J80 87-02 98-43 9007314-1624 Screw, M16 x130 (SB-1989-023 on page 268) 4
J90 07-44 4800482 A pad seal (SB-2007-027 on page 313) 1
J90 87-02 07-43 545434 (9004100-0420) O-ring 1
J92 07-44 4460586 Cover plate (SB-2007-027 on page 313) 1
J92 87-02 07-43 9802336 Cover plate 1
J95 87-02 9007200-3714 Screw 3
* For information regarding replacement parts for units built from 89-17 to 93-09, refer to AN152886483362 in the appendix. New style covers may be
used with either charge pump design.
Order code: AC & T

J10 87-02 8100297 Coupling, 11 tooth 1
& SB-2005-011 on page 310)
& SB-2005-011 on page 310)
J30 87-02 664771 (8700008) Bushing 1
J40 87-02 92-29 680892 (9004104-0440) O-ring 1
J50 87-02 056739 (9004104-1580) O-ring 1
J60 87-02 8200467 Flange adapter, SAE A (SB-2007-027 on page 313) 1
J80 98-44 518721 Screw, M16 x 140 4
J80 87-02 98-43 9007314-1624 Screw M16 x 130 4
J90 07-44 4800482 A pad seal (SB-2007-027 on page 313) 1
J90 87-02 07-43 545434 (9004100-0420) O-ring 1
J92 87-02 07-43 9802336 Cover plate 1
J95 87-02 9007200-3714 Screw 2

Parts Manual
Auxiliary mounting
S90 100cc pump aux mounting AG-BB, V

Parts configuration
(AG)
J10
J60
(BA)
J80
J10
*J50 J15
J30
J60
J90
J92
J95 J80
*J50
J92
J90 J10
J95 J15
J30
Design prior to 08-10

J60 *J40
J70
J80
J60 *J50 (BB & V)
J90 J80
J92
J95
J90 Design after 08-09
J95
J92

Parts Manual
Auxiliary mounting
Order code: AG
Model/Kit
J10 09-29 8100147 Coupling, 9 tooth 1
J50 09-29 056739 (9004104-1580) O-ring 1
J60 09-29 8200467 Flange adapter, SAE A 1
J80 09-29 518721 Screw, M16x 140 4
J90 09-29 4800482 A-pad seal 1
J92 09-29 4460586 Cover plate 1
J95 09-29 9007200-3714 Screw 2
Order code: BA
J10 05-14 8100273 Coupling, 15 tooth 1
J15 05-14 8801248 Cover assembly, CW 1
J15 05-14 8801352 Cover assembly, CCW 1
J30 05-14 664771 (8700008) Bushing 1
J50 05-14 056739 (9004104-1580) O-ring 1
J60 05-14 8200468 Flange adapter, SAE B 1
J80 05-14 518721 Screw, M16 x 140 4
J90 05-14 8801061 B-pad seal 1
J92 05-14 8801059 Cover plate 1
J95 05-14 9007200-5021 Screw 2
Order code: BB & V

J10 87-02 8100273 Coupling, 15 tooth 1
& SB-2005-011 on page 310)
& SB-2005-011 on page 310)
J30 87-02 664771 (8700008) Bushing 1
J40 87-02 92-15 680892 (9004104-0440) O-ring 1
J50 87-02 056739 (9004104-1580) O-ring 1
J60 87-02 8200468 Flange adapter, SAE B (SB-2007-055 on page 317) 1
J70 87-02 08-09 9009625-0132 Washer (SB-2007-055 on page 317) 4
J80 98-44 518721 Screw, M16 x 140 4
J80 87-02 98-43 9007314-1624 Screw M16 x 130 (SB-1989-023 on page 268) 4
J90 08-10 8801061 B-pad seal (SB-2007-055 on page 317) 1
J90 87-02 08-09 726935 (9004104-0450) O-ring 1
J92 87-02 08-09 4460370 Cover plate 1
J95 87-02 9007200-5021 Screw 2

Parts Manual
Auxiliary mounting
S90 100cc pump aux mounting BC, BD, BE

Parts configuration
J10
J15
(BC & BE)
J30
J60 *J40
J70 (used prior to 92-30)
J80
J60 *J50
J90 J80
J92
J95
J90

J92
J10
Design prior to 08-10 J60 (BD)
J70
J80
J60 *J50
J90 J80
J92
J95
J95
J92

Parts Manual
Auxiliary mounting
Order code: BC & B

Model/Kit
J10 87-02 8100148 Coupling, 13 tooth 1
& SB-2005-011 on page 310)
& SB-2005-011 on page 310)
J30 87-02 664771 (8700008) Bushing 1
J40 87-02 92-15 680892 (9004104-0440) O-ring 1
J50 87-02 056739 (9004104-1580) O-ring 1
J80 98-44 518721 Screw, M16 x 140 4
J80 87-02 98-43 9007314-1624 Screw M16 x130 (SB-1989-023 on page 268) 4
J90 87-02 08-09 726935 (9004104-0450) O-ring 1
J92 87-02 08-09 4460370 Cover plate 1
J95 87-02 9007200-5021 Screw 2
Order code: BD
J10 99-17 8100148 Coupling, 13 tooth 1
J50 99-17 056739 (9004104-1580) O-ring 1
J80 99-17 518721 Screw, M16 x 140 4
J90 08-10 8801061 B pad seal (SB-2007-055 on page 317) 1
J90 99-17 08-09 726935 (9004104-0450) O-ring 1
J92 99-17 08-09 4460370 Cover plate 1
J95 99-17 370320 Screw 2

Parts Manual
Auxiliary mounting
Parts configuration
J10
J15
(BC & BE)
J30
J60 *J40
J80
J60 *J50
J90 J80
J92
J95
J90

J92
J10
Design prior to 08-10 J60 (BD)
J70
J80
J60 *J50
J90 J80
J92
J95
J95
J92

Parts Manual
Auxiliary mounting
Order code: BE & P

Model/Kit
J10 87-02 8100148 Coupling, 13 tooth 1
& SB-2005-011 on page 310)
& SB-2005-011 on page 310)
J30 87-02 664771 (8700008) Bushing 1
J40 87-02 92-15 680892 (9004104-0440) O-ring 1
J50 87-02 056739 (9004104-1580) O-ring 1
J80 98-44 518721 Screw, M16 x 140 4
J90 87-02 08-09 726935 (9004104-0450) O-ring 1
J92 87-02 08-09 4460370 Cover plate 1
J95 87-02 370320 (9007314-1207) Screw 2

Parts Manual
Auxiliary mounting
S90 100cc pump aux mounting BF, BL

Parts configuration
J10
J15
(BF) J30
J60
*J40
J80
*J50
J60
J90 J80
J92
J95
J90
Design after 08-09
J95
J92
J10
(BL) J15
J30
J60
J80
*J50
J92
J90
J95

Parts Manual
Auxiliary mounting
Order code: BF & BL

Model/Kit
J10 87-02 11053342 Coupling, 19 tooth 1
& SB-2005-011 on page 310)
& SB-2005-011 on page 310)
J30 87-02 664771 (8700008) Bushing 1
J40 87-02 92-15 680892 (9004104-0440) O-ring 1
J50 87-02 056739 (9004104-1580) O-ring 1
J80 98-44 518721 Screw, M16 x 140 4
J90 87-02 08-09 726935 (9004104-0450) O-ring 1
J92 87-02 08-09 4460370 Cover plate 1
J95 87-02 9007200-5021 Screw 2
Order code: BL
J10 06-01 8100148 Coupling, 13 tooth 1
J30 06-01 664771 (8700008) Bushing 1
J50 06-01 056739 (9004104-1580) O-ring 1
J80 06-01 518721 Screw, M16 x 140 4
J90 06-01 8801061 B pad seal (SB-2007-055 on page 317) 1
J95 06-01 9007200-5021 Screw 2

Parts Manual
Auxiliary mounting
S90 100cc pump aux mounting BM, BU, C2, CA

Parts configuration
J10
(BM, BU & 7)
J15
J30
Design prior to 08-10 (BM & 7)
J60 *J40
J70
J80
J60 *J50
J90 J80
J92
J95
Design after 08-09 (BM & 7)

J90
J95
J92
J10
J15
J30
(C2 & CA)
J60
Design prior to 09-30 (C2)
J80
J60
*J50
J90
J95
J92
Design after 09-29 (C2)
J90
J95
J92
J80

Parts Manual
Auxiliary mounting
Order code: BM & 7

Model/Kit
J10 94-16 8100273 Coupling,15 tooth 1
J15 94-16 8800832 Cover assembly,CW (SB-2005-011 on page 310) 1
J15 94-16 8800833 Cover assembly,CCW (SB-2005-011 on page 310) 1
J30 94-16 664771 (8700008) Bushing 1
J50 94-16 056739 (9004104-1580) O-ring 1
J60 94-16 8200540 Flange adapter, SAE B, metric threads 1
(SB-2007-055 on page 317)
J70 94-16 08-09 9009625-0132 Washer(SB-2007-055 on page 317) 4
J80 98-44 518721 Screw, M16x 140 4
J90 06-13 08-09 726935 (9004104-0450) O-ring 1
J92 94-16 08-09 4460370 Cover plate 1
J95 94-16 737866 (9007314-1207) Screw 2
Order code: BU
J10 07-10 8100297 Coupling, 15 tooth 1
J30 07-10 664771 (8700008) Bushing 1
J50 07-10 056739 (9004104-1580) O-ring 1
J60 07-10 8200540 Flange adapter, SAE B 1
J80 07-10 518721 Screw, M16x 140 4
J90 07-10 8801061 B-pad seal 1
J92 07-10 8801059 Cover plate 1
J95 07-10 9007314-1207 Screw 2
Order code: C2
J10 06-43 11017038 Coupling, 25 tooth,high strength 1
J30 06-43 664771 (8700008) Bushing 1
J50 06-43 056739 (9004104-1580) O-ring 1
J60 06-43 8200515 Flange adapter, SAE C (SB-2007-051 on page 315) 1
J80 06-43 518721 Screw, M16x 140 4
J90 09-30 11081805 C-pad seal (SB-2007-051 on page 315) 1
J90 06-43 09-29 726943 (9004104-0490) O-ring 1
J92 06-43 09-29 8800406 Cover plate 1
J95 06-43 9007200-5021 Screw 4

Parts Manual
Auxiliary mounting
Parts configuration
J10
(BM, BU & 7)
J15
J30
Design prior to 08-10 (BM & 7)
J60 *J40
J70
J80
J60 *J50
J90 J80
J92
J95
Design after 08-09 (BM & 7)

J90
J95
J92
J10
J15
J30
(C2 & CA)
J60
Design prior to 09-30 (C2)
J80
J60
*J50
J90
J95
J92
Design after 09-29 (C2)
J90
J95
J92
J80

Parts Manual
Auxiliary mounting
Order code: CA
Model/Kit
J15 06-01 8800832 Cover assembly,CW (SB-2005-011 on page 310) 1
J30 06-01 664771 (8700008) Bushing 1
J50 06-01 056739 (9004104-1580) O-ring 1
J60 06-01 8200515 Flange adapter, SAE C 1
J80 06-01 518721 Screw, M16x 140 4
J90 06-01 11081805 C-pad seal 1
J92 06-01 8801060 Cover plate 1
J95 06-01 9007200-5021 Screw 4

Parts Manual
Auxiliary mounting
S90 100cc pump aux mounting CB, CC, CD

Parts configuration
J15
(CB, CC) J30
J10
J60
J97
*J50
J80
J90
J80
J97
J92
J95
J10
(C & CD) J15
Design prior to 08-10 J30
J60
J80
J60
*J50
J90
J95
J92
Design after 08-09
J90
J95
J92
J80

Parts Manual
Auxiliary mounting
Order code: CB
Model/Kit
J15 03-35 8801248 Cover assembly, CW (SB-2005-011 on page 310) 1
J30 03-35 664771 (8700008) Bushing 1
J50 03-35 056739 (9004104-1580) O-ring 1
J80 03-35 518721 Screw, M16x 140 4
J90 03-35 11081805 C-pad seal 1
J92 03-35 8801060 Cover plate 1
J95 03-35 9007200-5021 Screw 4
J97 03-35 8200549 Mounting bracket 1
Order code: CC
J10 13-07 11053346 Coupling, 14 tooth, high strength 1
J30 13-07 664771 (8700008) Bushing 1
J50 13-07 056739 (9004104-1580) O-ring 1
J80 13-07 518721 Screw, M16x 140 4
J90 13-07 11081805 C-pad seal 1
J92 13-07 8801060 Cover plate 1
J95 13-07 9007200-5021 Screw 4
J97 13-07 8200549 Mounting bracket 1
Order code: C & CD

J15 87-02 8800832 Cover assembly, CW (SB-1993-001 on page 273 & 1
SB-2005-011 on page 310)
J15 87-02 8800833 Cover assembly, CCW (SB-1993-001 on page 273 1
& SB-2005-011 on page 310)
J30 87-02 664771 (8700008) Bushing 1
J40 87-02 92-15 680892 (9004104-0440) O-ring 1
J50 87-02 056739 (9004104-1580) O-ring 1
J70 87-02 03-10 5000602 Washer(SB-2002-050 on page 309) 4
J80 98-44 518721 Screw, M16 x 140 4
J90 87-02 08-09 726943 (9004104-0490) O-ring 1
J92 87-02 08-09 8800406 Cover plate 1
J95 87-02 9007200-5021 Screw 4

Parts Manual
Auxiliary mounting
S90 100cc pump aux mounting CE, CJ, CK

Parts configuration
J15
J30
(CE)
J10
J60
*J50
J90
J80
J92
J95
J10
J15
J30
Design prior to 09-30 (CK)
(CJ & CK)
J60
J70
J80
J60
*J50
J90
J95
J92
Design after 09-29 (CK)

J90
J95
J92
J80

Parts Manual
Auxiliary mounting
Order code: CE
Model/Kit
J30 02-08 664771 (8700008) Bushing 1
J50 02-08 056739 (9004104-1580) O-ring 1
J80 02-08 518721 Screw, M16x 140 4
J90 02-08 11081805 C-pad seal 1
J92 02-08 8801060 Cover plate 1
J95 02-08 9007200-5021 Screw 4
Order code: CJ
J30 02-08 664771 (8700008) Bushing 1
J50 02-08 056739 (9004104-1580) O-ring 1
J80 02-08 518721 Screw, M16x 140 4
J90 02-08 11081805 C-pad seal 1
J92 02-08 8801060 Cover plate 1
J95 02-08 9007200-5021 Screw 4
Order code: CK
J15 94-18 8800832 Cover assembly, CW (SB-1993-001 on page 273 & 1
SB-2005-011 on page 310)
J15 94-18 8800833 Cover assembly, CCW (SB-1993-001 on page 273 1
& SB-2005-011 on page 310)
J30 94-18 664771 (8700008) Bushing 1
J50 94-18 056739 (9004104-1580) O-ring 1
J70 94-18 09-29 5000602 Washer (SB-2002-050 on page 309) 4
J80 98-44 518721 Screw, M16x 140 4
J90 94-18 09-29 726943 (9004104-0490) O-ring 1
J92 94-18 09-29 8800406 Cover plate 1
J95 94-18 9007200-5021 Screw 4

Parts Manual
Auxiliary mounting
S90P aux mounting CP, CR

Parts configuration
J15
J30
(CP) J10
J60
J70
J80
J90
J60 *J50
J90
J92
J95
Design after 09-29
J80
J92
J95
J60
(CR)
J90 J10
*J50
J60
J90
J80
J95
J92
J80
Design after 08-09
J95
J92

Parts Manual
Auxiliary mounting
Order code: CP
Model/Kit
& SB-2005-011 on page 310)
& SB-2005-011 on page 310)
J30 94-18 664771 (8700008) Bushing 1
J50 94-18 056739 (9004104-1580) O-ring 1
J70 94-18 09-29 664920 Washer 4
J80 98-44 518721 Screw, M16x 140 4
J90 94-18 09-29 726943 (9004104-0490) O-ring 1
J92 94-18 09-29 8800406 Cover plate 1
J95 94-18 9007200-6222 Screw 2
Order code: CR
J50 03-14 056739 (9004104-1580) O-ring 1
J80 03-14 518721 Screw, M16x 140 4
J90 03-14 08-09 726943 (9004104-0490) O-ring 1
J92 03-14 08-09 8800406 Cover plate 1
J95 03-14 370320 Screw 4

Parts Manual
Auxiliary mounting
S90 100cc pump aux mounting CT, CU

Parts configuration
J10
J15
J30
Design prior to 08-10 (CT)
J60
J70
J80
J60
*J50
J90
J92
J95
Design after 08-09

J90
J95
J92
J80
Design prior to 10-30 J60

J70 (CU)
J80 J10
J90
*J50
J60
J90
J95
J92
Design after 10-29
J95
J92

Parts Manual
Auxiliary mounting
Order code: CT
Model/Kit
J10 98-42 11053342 Coupling, 19 tooth 1
J15 98-42 8800833 Cover assembly, CCW (SB-2005-011 on page 310) 1
J30 98-42 664771 (8700008) Bushing 1
J50 98-42 056739 (9004104-1580) O-ring 1
J60 98-42 8200515 Flange adapter, SAE C (SB-2002-050 on page 309 1
& SB-2007-051 on page 315)
J70 98-42 03-10 5000602 Washer(SB-2002-050 on page 309) 4
J80 98-44 518721 Screw, M16 x 140 4
J90 08-10 11081805 C-pad seal 1
J90 98-42 08-09 719179 (9004100-0480) O-ring 1
J92 08-10 8801060 Cover plate 1
J92 98-42 08-09 8800406 Cover plate 1
J95 98-42 9007200-5021 Screw 4
Order code: CU
J50 99-04 056739 (9004104-1580) O-ring 1
J70 99-04 04-02 5000602 Washer (SB-2002-050 on page 309) 4
J80 99-04 518721 Screw, M16 x 140 4
J90 99-04 10-29 726943 (9004104-0490) O-ring 1
J92 99-04 10-29 8800406 Cover plate 1
J95 99-04 9007200-5021 Screw 4

Parts Manual
Auxiliary mounting
S90 100cc pump aux mounting NN, NU

Parts configuration
(NN)
J40
J15
J30
J80
(NU)
J80
* Included in overhaul seal kit Q210

Parts Manual
Auxiliary mounting
Order code: NN & N

Model/Kit
J15 87-02 8800834 Cover assembly, (SB-1993-001 on page 273*) 1
J30 87-02 664771 (8700008) Bushing 1
J40 87-02 680892 (9004104-0440) O-ring 1
J80 98-44 9007210-1621 Screw, M16 x 120 4
J80 87-02 98-43 9007210-1620 Screw, M16 x 100 4
* For additional information regarding replacement parts for units built prior to 93-10, refer to AN152886483362 in the appendix
Order code: NU
J80 98-47 9007210-1621 Screw, M16 x 120 4

Parts Manual
S90 100cc pump charge pressure system 08-42, XX

Parts configuration
QK10
*K50

Parts Manual
Order code: 08-30

Model/Kit
K50 87-42 001149 (9004201-6200) O-ring (SB-1989-002 on page 263) 1
QK10 87-42 8002K000-A Charge relief valve kit, 8-30 bar (SB-1989-002 on 1
page 263)
Order code: 32-42

K50 94-13 001149 (9004201-6200) O-ring 1
QK10 94-13 8510269 Charge relief valve kit, 30-42 bar 1
Order code: JD
No parts
Order code: XX
K50 94-13 012559 (9004202-6200) O-ring, viton 1
QK10 94-13 11086335 Charge relief valve kit, viton 1

Parts Manual
Shaft
S90 100cc pump shaft C6-S3

Parts configuration
(C6, C7, D7, F1, F5,

F7, G1, S1, S3) (F3)
L100 L100
L80
(J2 & J3) (K3)
L100
L100

Parts Manual
Shaft
Order code: C6
Model/Kit
L100 98-38 509239 Shaft, 21 tooth spline 1
Order code: C7
L100 89-46 341958 (8200169) Shaft, 23 tooth spline 1
L100 87-02 89-45 320911 (8200119) Shaft, 23 tooth spline (SB-1989-023 on page 268) 1
Order code: D7
L100 94-14 504307 Shaft, 23 tooth spline, M10 threaded tapped hole 1
Order code: F1
Order code: F3
L100 96-45 8200330 Shaft, 13 tooth spline with retaining ring grooves 1
Order code: F5
L100 13-49 11137386 Shaft, 13 tooth spline, 5/8-11 threaded tapped 1
hole
Order code: F7
Order code: G1
Order code: J2
L100 92-16 8200389 Shaft, 23 tooth spline with no relief 1
Order code: J3
L100 92-16 8200234 Shaft, 14 tooth spline with no relief 1

Parts Manual
Shaft
Parts configuration
(C6, C7, D7, F1, F5,

F7, G1, S1, S3) (F3)
L100 L100
L80
(J2 & J3) (K3)
L100
L100

Parts Manual
Shaft
Order code: K3
Model/Kit
L80 87-02 9003261-3724 Key 1
L100 89-46 8200176 Shaft, straight key, 1.75” diameter 1
L100 87-02 89-45 8200164 Shaft, straight key, 1.75” diameter (SB-1989-023 1
on page 268)
Order code: S1
Order code: S3
L100 87-02 89-45 8200120 Shaft, 16 tooth spline (SB-1989-023 on page 268) 1

Parts Manual
Shaft
S90 100cc pump shaft T2-TJ

Parts configuration
L90 L90
L80 (T6) L500
(T2)
L100 L61
L100
L90
L90 L500
L200
(TF) (TG)
L61
L100
L100
L90
L500
L200
(TJ)
L100

Parts Manual
Shaft
Order code: T2
Model/Kit
L61 87-02 716779 (9004600-1230) Cotter pin 1
L80 87-02 9003310-3724 Key 1
L90 87-02 5000606 Slotted nut 1
L100 89-46 342006 (11111525) Shaft, 1.5” tapered 1
L100 87-02 89-45 8200133 Shaft, 1.5” tapered (SB-1989-023 on page 268) 1
Order code: T6
L90 97-42 504060 Slotted nut 1
L100 97-42 511617 Shaft, 1.5” tapered 1
L500 97-42 511627 Washer 1
Order code: TF
L61 87-02 716779 (9004600-1230) Cotter pin 1
L90 87-02 9700189 Slotted nut 1
L100 89-46 342006 (8200179) Shaft, 1.5” tapered spline 1
L100 87-02 89-45 8200132 Shaft, 1.5” tapered spline (SB-1989-023 on page 1
268)
Order code: TG
L90 97-42 504060 Lock nut, M24 1
L100 97-42 511617 Shaft, 1.5” tapered spline 1
L200 97-42 504061 Flange 1
L500 97-42 511627 Washer 1
Order code: TJ
L90 97-42 504060 Lock nut, M24 1
L100 97-42 511617 Shaft, 1.5” tapered spline 1
L200 97-42 511462 Flange 1
L500 97-42 511627 Washer 1

Parts Manual
Controls
S90P control CA-DD

Parts configuration
(CA) (DC & DD)

QM10
M90 M29
QM10
M76
*QM031
M11
M90
QM10
(CB)
M90
View A
*M11
M11
View “A”
T70 T50
T80
T20
(supply)
T30
M14 T40
Possible orifice locations
All orifices present in the original control must be transferred to the replacement control. If replacement
control contains pre-installed orifices, remove and discard them before transferring existing orifices to
new control.

Parts Manual
Controls
Order code: CA
Model/Kit
M11 87-02 8800923 Control gasket 1
M90 87-02 693341 (9007314-0606) Screw 6
QM10 87-02 8102M0CA-A Control cover plate kit 1
Order code: CB
M14 96-40 11070306 Feedback link (SB-1999-019 on page 298 & 1
SB-2013-011 on page 324)
M14 87-02 96-39 8200344 Feedback link (SB-1996-009 on page 287) 1
M90 87-02 693341 (9007314-0606) Screw 6
QM10 87-02 8102M0CA-A Control cover plate kit 1
Order code: DC
M29 87-02 035592 Screw 4
M76 87-02 687103 Solenoid valve, 12v 1
M90 87-02 693341 (9007314-0606) Screw 6
QM10 87-02 8102M0DC-A Control kit, 12v 1
QM031 87-02 11099647 O-ring kit 1
QM210 87-02 11096172 Control seal kit 1
Order code: DD
M29 87-02 035592 Screw 4
M76 87-02 549907 Solenoid valve, 24v 1
M90 87-02 693341 (9007314-0606) Screw 6
QM10 87-02 8102M0DD-A Control kit, 24v 1
QM031 87-02 11099647 O-ring kit 1

Parts Manual
Controls
S90 100cc pump control EA-EP

Parts configuration
M9 M29
QM10
*M97
M90 *M96
*M95
*M51
View A
*M11
View “A”
M14
T20
(supply) T60
T50
(drain) T70 T80 (drain)
(servo feed) T30 (servo feed)
T40
(Possible orifice locations)
new control.
Generic PCP and swashplate used to show part location only.
* Included in control seal kit QM210

Parts Manual
Controls
Order code: EA
Model/Kit
M9 91-16 MCV110A1017 PCP, MS connector 1
SB-2013-011 on page 324)
M29 91-16 K07067 Screw 4
M51 91-16 9003509-0008 Seal nut 1
M90 91-16 692889 (9007314-0611) Screw 6
M95 91-16 318337 (9004104-0120) O-ring 2
M96 91-16 011304 (9004104-0140) O-ring 1
M97 91-16 318345 (9004104-0240) O-ring 1
QM10 91-16 8202M0EA-B EDC kit, MS connector 1
Order code: EH
SB-2013-011 on page 324)
M29 99-05 K07067 Screw 4
M51 99-05 9003509-0008 Seal nut 1
M90 99-05 692889 (9007314-0611) Screw 6
M95 99-05 318337 (9004104-0120) O-ring 2
M96 99-05 011304 (9004104-0140) O-ring 1
M97 99-05 318345 (9004104-0240) O-ring 1
QM10 99-05 11013636 EDC kit, MS connector 1
Order code: EK
M9 99-15 MCV110A1014 PCP, DEUTSCH connector 1
SB-2013-011 on page 324)
M29 99-15 K07067 Screw 4
M51 99-15 9003509-0008 Seal nut 1
M90 99-15 692889 (9007314-0611) Screw 6
M95 99-15 318337 (9004104-0120) O-ring 2
M96 99-15 011304 (9004104-0140) O-ring 1
M97 99-15 318345 (9004104-0240) O-ring 1
QM10 99-15 11018282 EDC kit, DEUTSCH connector 1

Parts Manual
Controls
Parts configuration
M9 M29
QM10
*M97
M90 *M96
*M95
*M51
View A
*M11
View “A”
M14
T20
(supply) T60
T50
T40
new control.
Generic PCP and swashplate used to show part location only.

Parts Manual
Controls
Order code: EP
Model/Kit
M9 91-07 MCV110A1058 PCP, Packard connector 1
SB-2013-011 on page 324)
M29 91-07 K07067 Screw 4
M51 91-07 9003509-0008 Seal nut 1
M90 91-07 692889 (9007314-0611) Screw 6
M95 91-07 318337 (9004104-0120) O-ring 2
M96 91-07 011304 (9004104-0140) O-ring 1
M97 91-07 318345 (9004104-0240) O-ring 1
QM10 91-07 8202M0EP-B EDC kit, Packard connector 1

Parts Manual
Controls
S90 100cc pump control EV-EZ

Parts configuration
M9
QM10 M29
*M97
M90 *M96
*M95
*M51
View A
*M11
View “A”
M14
T20
T50 (supply) T60
T70 T80
(drain) (drain)
(servo feed) (servo feed)
T30
T40

Parts Manual
Controls
Order code: EV
Model/Kit
SB-2013-011 on page 324)
M29 97-24 K07067 Screw 4
M51 97-24 9003509-0008 Seal nut 1
M90 97-24 692889 (9007314-0611) Screw 6
M95 97-24 318337 (9004104-0120) O-ring 2
M96 97-24 011304 (9004104-0140) O-ring 1
M97 97-24 318345 (9004104-0240) O-ring 1
QM10 97-24 11013636 EDC kit, Packard connector 1
Order code: EX
M9 99-05 MCV110A1090 PCP, Metripack connector 1
SB-2013-011 on page 324)
M29 99-05 K07067 Screw 4
M51 99-05 9003509-0008 Seal nut 1
M90 99-05 692889 (9007314-0611) Screw 6
M95 99-05 318337 (9004104-0120) O-ring 2
M96 99-05 011304 (9004104-0140) O-ring 1
M97 99-05 318345 (9004104-0240) O-ring 1
QM10 99-05 11099895 EDC kit, Metripack connector 1
Order code: EZ
SB-2013-011 on page 324)
M14 97-24 96-39 8200344 Feedback link (SB-1996-009) 1
M29 94-29 K07067 Screw 4
M51 94-29 9003509-0008 Seal nut 1
M90 94-29 692889 (9007314-0611) Screw 6
M95 94-29 318337 (9004104-0120) O-ring 2
M96 94-29 011304 (9004104-0140) O-ring 1
M97 94-29 318345 (9004104-0240) O-ring 1
QM10 94-29 11099896 EDC kit, MS connector 1

Parts Manual
Controls
S90P control FA-FD

Parts configuration
QM10
M90
M005
M92
M007 M76
View A M29
*QM034
*M11
T70
T80
View “A”
T50
All orifices present in the original control must be transferred to the replacement control. If the
replacement control contains pre-installed orifices, remove and discard them before transferring existing
orifices to the new control.

Parts Manual
Controls
Order code: FA
Model/Kit
M29 98-14 067694 Screw 4
M76 98-14 518080 Solenoid valve, 12 volt, 25 bar 2
M90 98-14 9007314-0614 Screw 3
M92 98-14 693341 (9007314-0606) Screw 3
M007 98-14 K00775 Filter screen 1
QM10 98-14 11015079 NFPE control kit, 12 volt, 25 bar 1
QM034 98-14 11099849 Solenoid valve seal kit 2
Order code: FB
M29 98-14 067694 Screw 4
M90 98-14 9007314-0614 Screw 3
M92 98-14 693341 (9007314-0606) Screw 3
Order code: FC
M29 98-14 067694 Screw 4
M90 98-14 9007314-0614 Screw 3
M92 98-14 693341 (9007314-0606) Screw 3
Order code: FD
M29 98-14 067694 Screw 4
M90 98-14 9007314-0614 Screw 3
M92 98-14 693341 (9007314-0606) Screw 3

Parts Manual
Controls
S90P control FG, FH

Parts configuration
M90
M005
QM10
M92
View A
M76
M037
M036
*M11
*QM034
T70
T80
View “A”
T50

Parts Manual
Controls
Order code: FG
Model/Kit
M90 00-30 9007314-0614 Screw 3
M92 00-30 693341 (9007314-0606) Screw 3
M005 00-30 11040532 Plug assembly 2
QM036 00-30 518088 Coil nut kit 2
QM037 00-30 516003 Coil, 12v Jet connector 2
Order code: FH
M90 00-30 9007314-0614 Screw 3
M92 00-30 693341 (9007314-0606) Screw 3
M005 00-30 11040532 Plug assembly 2
QM036 00-30 518088 Coil nut kit 2
QM037 00-30 516004 Coil, 24v Jet connector 2

Parts Manual
Controls
S90 100cc pump control GA

Parts configuration
M9
QM10 M29
*M97
M90 *M96
*M95
*M51
View A
*M11
View “A”
M14
T20
T50 (supply) T60
T70 T80
(drain) (drain)
T30
T40

Parts Manual
Controls
Order code: GA
Model/Kit
M14 01-28 11070306 Feedback link (SB-2013-011 on page 324) 1
M29 01-28 K07067 Screw 4
M51 01-28 9003509-0008 Seal nut 1
M90 01-28 692889 (9007314-0611) Screw 6
M95 01-28 318337 (9004104-0120) O-ring 2
M96 01-28 011304 (9004104-0140) O-ring 1
M97 01-28 318345 (9004104-0240) O-ring 1
QM10 01-28 8510302 EDC kit, Packard connector 1

Parts Manual
Controls
S90P control HD, HE

Parts configuration
M90 QM10
*M51
View A
*M11
View “A”
M14
T20
T50 (supply) T80 T60
T70
(drain) (drain)
T30
T40

Parts Manual
Controls
Order code: HD
Model/Kit
SB-2013-011 on page 324)
M51 97-44 505412 (9003509-0008) Seal nut 1
M90 97-44 692889 (9007314-0611) Screw 6
QM10 97-44 11087556 HDC kit, 6-18 bar 1
Order code: HE
M11 97-06 8801241 Control gasket (SB-1999-065 on page 302) 1
SB-2013-011 on page 324)
M51 97-06 505412 (9003509-0008) Seal nut 1
M90 97-06 692889 (9007314-0611) Screw 6
QM10 97-06 8510277 HDC kit, 8-16.5 bar 1

Parts Manual
Controls
S90P control HF-HS

Parts configuration
M90
QM10
*M51
View A
*M11
View “A”
M14
T20
T70
(drain) (drain)
T30
T40

Parts Manual
Controls
Order code: HF
Model/Kit
SB-2013-011 on page 324)
M51 92-15 505412 (9003509-0008) Seal nut 1
M90 92-15 692889 (9007314-0611) Screw 6
QM10 92-15 8202M0HF-A HDC kit, 3-11 bar 1
Order code: HK
SB-2013-011 on page 324)
M51 92-15 505412 (9003509-0008) Seal nut 1
M90 92-15 692889 (9007314-0611) Screw 6
QM10 92-15 8202M0HK-A HDC kit, 1-11 bar 1
Order code: HM
M11 92-15 8801241 Control gasket (SB-1999-065) 1
SB-2013-011 on page 324)
M51 92-15 505412 (9003509-0008) Seal nut 1
M90 92-15 692889 (9007314-0611) Screw 6
QM10 92-15 8202M0HM-A HDC kit, 1.1 -6.7 bar 1
Order code: HS
SB-2013-011 on page 324)
M51 94-19 505412 (9003509-0008) Seal nut 1
M90 94-19 692889 (9007314-0611) Screw 6
QM10 94-19 8202M0HS-A HDC kit, 6-18 bar 1

Parts Manual
Controls
S90 100cc pump control HT-JC

Parts configuration
M90
QM10
*M51
View A
*M11
View “A”
M14
T20
T50 (supply) T60
T70 T80
(drain) (drain)
T30
T40

Parts Manual
Controls
Order code: HT
Model/Kit
SB-2013-011 on page 324)
M51 94-36 505412 (9003509-0008) Seal nut 1
M90 94-36 692889 (9007314-0611) Screw 6
QM10 94-36 11020564 HDC kit, high accuracy 1
Order code: HV
SB-2013-011 on page 324)
M51 94-36 505412 (9003509-0008) Seal nut 1
M90 94-36 692889 (9007314-0611) Screw 6
QM10 94-36 11013639 HDC kit, 4-39 bar 1
Order code: HW
SB-2013-011 on page 324)
M51 98-13 505412 (9003509-0008) Seal nut 1
M90 98-13 692889 (9007314-0611) Screw 6
QM10 98-13 11013639 HDC kit, 4-14 bar 1
Order code: HX
M51 00-19 505412 (9003509-0008) Seal nut 1
M90 00-19 692889 (9007314-0611) Screw 6
QM10 00-19 11019662 HDC kit, 3-11 bar 1
Parts continue to next 2 pages.

Parts Manual
Controls
Parts configuration
M90
QM10
*M51
View A
*M11
View “A”
M14
T20
T50 (supply) T60
T70 T80
(drain) (drain)
T30
T40

Parts Manual
Controls
Order code: JA
Model/Kit
M51 00-24 505412 (9003509-0008) Seal nut 1
M90 00-24 692889 (9007314-0611) Screw 6
QM10 00-24 8202M0HS-A HDC kit, 6-18 bar 1
Order code: JC
M14 03-06 11070306 Feedback link 1
M51 03-06 505412 (9003509-0008) Seal nut 1
M90 03-06 692889 (9007314-0611) Screw 6
QM10 03-06 11099898 HDC kit, 6-18 bar, steel barrel 1

Parts Manual
Controls
S90 100cc pump control K1-K9

Parts configuration
QM10
M29
M9
M90
*M99
*M96 *M97
*M51
View A
*M11
View “A”
M14
T20
T50 (supply) T60
T70 T80
(drain) (drain)
T30
T40
Generic PCP and swashplate shown.

Parts Manual
Controls
Order code: K1
Model/Kit
M9 12-36 14-37 MCV116C3201 PCP, DEUTSCH connector, dual coil 1
M11 12-36 14-37 8800923 Control gasket 1
M29 12-36 14-37 K07067 Screw 4
M51 12-36 14-37 505412 (9003509-0008) Seal nut 1
M90 12-36 14-37 692889 (9007314-0611) Screw 6
M96 12-36 14-37 011296 (9004105-0120) O-ring 3
M97 12-36 14-37 9004105-0130 O-ring 2
M99 12-36 14-37 K08572 Filter assembly 1
QM10 12-36 14-37 11121536 EDC3 kit, DEUTSCH connector, dual coil 1
QM210 12-36 14-37 11095724 Control seal kit 1
Order code: K7
M9 13-36 11101116 PCP, MS connector 1
M14 13-36 11070306 Feedback link 1
M29 13-36 K07067 Screw 4
M51 13-36 505412 (9003509-0008) Seal nut 1
M90 13-36 692889 (9007314-0611) Screw 6
M96 13-36 011296 (9004105-0120) O-ring 3
M97 13-36 9004105-0130 O-ring 2
M99 13-36 K08572 Filter assembly 1
QM10 13-36 11139994 EDC3 kit, MS connector 1
Order code: K8
M14 14-15 11070306 Feedback link 1
M29 14-15 K07067 Screw 4
M51 14-15 505412 (9003509-0008) Seal nut 1
M90 14-15 692889 (9007314-0611) Screw 6
M96 14-15 011296 (9004105-0120) O-ring 3
M97 14-15 9004105-0130 O-ring 2

Parts Manual
Controls
Parts configuration
QM10
M29
M9
M90
*M99
*M96 *M97
*M51
View A
*M11
View “A”
M14
T20
T50 (supply) T60
T70 T80
(drain) (drain)
T30
T40

Parts Manual
Controls
Order code: K9
Model/Kit
M14 14-36 11070306 Feedback link 1
M29 14-36 K07067 Screw 4
M51 14-36 505412 (9003509-0008) Seal nut 1
M90 14-36 692889 (9007314-0611) Screw 6
M96 14-36 011296 (9004105-0120) O-ring 3
M97 14-36 9004105-0130 O-ring 2

Parts Manual
Controls
S90 100cc pump control KA-KF

Parts configuration
QM10
M29
M9
M90
*M99
*M96 *M97
*M51
View A
*M11
View “A”
M14
T20
T50 (supply) T60
T70 T80
(drain) (drain)
T30
T40

Parts Manual
Controls
Order code: KA
Model/Kit
M9 95-17 MCV116G4201 PCP, MS connector, dual coil 1
SB-2013-011 on page 324)
M29 95-17 K07067 Screw 4
M51 95-17 505412 (9003509-0008) Seal nut 1
M90 95-17 692889 (9007314-0611) Screw 6
M96 95-17 011296 (9004105-0120) O-ring 3
M97 95-17 9004105-0130 O-ring 2
QM10 95-17 8510117 EDC3 kit, MS connector, dual coil 1
Order code: KB
M9 15-18 11164284 PCP, dual coil 1
M14 15-18 11070306 Feedback link 1
M29 15-18 K07067 Screw 4
M51 15-18 505412 (9003509-0008) Seal nut 1
M90 15-18 692889 (9007314-0611) Screw 6
M96 15-18 011296 (9004105-0120) O-ring 3
M97 15-18 9004105-0130 O-ring 2
QM10 15-18 11165456 EDC3 kit, MS connector, dual coil 1
Order code: KE
M9 03-27 MCV116F3118 PCP, DEUTSCH connector 1
SB-2013-011 on page 324)
M29 03-27 K07067 Screw 4
M51 03-27 505412 (9003509-0008) Seal nut 1
M90 03-27 692889 (9007314-0611) Screw 6
M96 03-27 011296 (9004105-0120) O-ring 3
M97 03-27 9004105-0130 O-ring 1
QM10 03-27 8510323 EDC3 kit, DEUTSCH connector 1

Parts Manual
Controls
Parts configuration
QM10
M29
M9
M90
*M99
*M96 *M97
*M51
View A
*M11
View “A”
M14
T20
T50 (supply) T60
T70 T80
(drain) (drain)
T30
T40

Parts Manual
Controls
Order code: KF
Model/Kit
M9 10-38 MCV116F3118 PCP, DEUTSCH connector 1
M14 10-38 11070306 Feedback link 1
M29 10-38 K07067 Screw 4
M51 10-38 505412 (9003509-0008) Seal nut 1
M90 10-38 692889 (9007314-0611) Screw 6
M96 10-38 011296 (9004105-0120) O-ring 3
M97 10-38 9004105-0130 O-ring 1

Parts Manual
Controls
S90 100cc pump control KK-KP

Parts configuration
QM10
M29
M9
M90
*M99
*M96 *M97
*M51
View A
*M11
View “A”
M14
T20
T50 (supply) T60
T70 T80
(drain) (drain)
T30
T40

Parts Manual
Controls
Order code: KK
Model/Kit
M9 98-37 MCV116G4211 PCP, Packard connector 1
M29 98-37 K07067 Screw 4
M51 98-37 505412 (9003509-0008) Seal nut 1
M90 98-37 692889 (9007314-0611) Screw 6
M96 98-37 011296 (9004105-0120) O-ring 3
M97 98-37 9004105-0130 O-ring 2
QM10 98-37 11013633 EDC3 kit, Packard connector 1
Order code: KM
M9 98-49 MCV116G4213 PCP, Metripak connector 1
M29 98-49 K07067 Screw 4
M51 98-49 505412 (9003509-0008) Seal nut 1
M90 98-49 692889 (9007314-0611) Screw 6
M96 98-49 011296 (9004105-0120) O-ring 3
M97 98-49 9004105-0130 O-ring 2
QM10 98-49 8510241 EDC kit, Metripak connector 1
Order code: KN
M9 95-51 MCV116A3501 PCP, MS connector, single coil 1
SB-2013-011 on page 324)
M29 95-51 K07067 Screw 4
M51 95-51 505412 (9003509-0008) Seal nut 1
M90 95-51 692889 (9007314-0611) Screw 6
M96 95-51 011296 (9004105-0120) O-ring 3
M97 95-51 9004105-0130 O-ring 2
QM10 95-51 8510209 EDC3 kit, MS connector, single coil 1

Parts Manual
Controls
Parts configuration
QM10
M29
M9
M90
*M99
*M96 *M97
*M51
View A
*M11
View “A”
M14
T20
T50 (supply) T60
T70 T80
(drain) (drain)
T30
T40

Parts Manual
Controls
Order code: KP
Model/Kit
M9 95-26 MCV116G4204 PCP, Weather-pack connector, dual coil 1
SB-2013-011 on page 324)
M29 95-26 K07067 Screw 4
M51 95-26 505412 (9003509-0008) Seal nut 1
M90 95-26 692889 (9007314-0611) Screw 6
M96 95-26 011296 (9004105-0120) O-ring 3
M97 95-26 9004105-0130 O-ring 2
QM10 95-26 8510118 EDC3 kit, Weather-pack connector, dual coil 1

Parts Manual
Controls
S90 100cc pump control KT-KW

Parts configuration
QM10
M29
M9
M90
*M99
*M96 *M97
*M51
View A
*M11
View “A”
M14
T20
T50 (supply) T60
T70 T80
(drain) (drain)
T30
T40

Parts Manual
Controls
Order code: KT
Model/Kit
M9 99-49 MCV116G4214 PCP, DEUTSCH connector 1
M14 99-49 11070306 Feedback link 1
M29 99-49 K07067 Screw 4
M51 99-49 505412 (9003509-0008) Seal nut 1
M90 99-49 692889 (9007314-0611) Screw 6
M96 99-49 011296 (9004105-0120) O-ring 3
M97 99-49 9004105-0130 O-ring 2
Order code: KU
M9 97-50 MCV116G4204 PCP, dual, Weather-Pack connector 1
M29 97-50 K07067 Screw 4
M51 97-50 505412 (9003509-0008) Seal nut 1
M90 97-50 692889 (9007314-0611) Screw 6
M96 97-50 011296 (9004105-0120) O-ring 3
M97 97-50 9004105-0130 O-ring 2
QM10 97-50 11020566 EDC3 kit, dual, Weather-Pack connector 1
Order code: KW
M9 97-50 MCV116G4201 PCP, MS connector 1
M29 97-50 K07067 Screw 4
M51 97-50 505412 (9003509-0008) Seal nut 1
M90 97-50 692889 (9007314-0611) Screw 6
M96 97-50 011296 (9004105-0120) O-ring 3
M97 97-50 9004105-0130 O-ring 2

Parts Manual
Controls
S90 100cc pump control LE, LG

Parts configuration
(LE) (LG)
QM10
QM10
M76
M72
M71
M70
QM89 M78
M72
*M77
M90 M75
M90 M71
M70
*M83
*M27
*M26
M27
M26
View A
*M11
View A
*M11
View “A”
M14
T20
T50 (supply) T60
T70 T80
(drain) (drain)
T30
T40

Parts Manual
Controls
Order code: LE
Model/Kit
M14 01-07 11070306 Feedback link 1
M26 01-07 144725 (9004105-0110) O-ring 1
M27 01-07 042507 (9006300-0044) Retaining ring 1
M70 01-07 9800916 Control handle 1
M71 01-07 689018 (9009660-3100) Toothlock washer 1
M72 01-07 040642 (9003513-0800) Nut 1
M83 01-07 001131 (9004201-5000) O-ring 1
M90 01-07 692889 (9007314-0611) Screw 6
QM10 01-07 8510291 MDC kit, high force neutral start switch 1
QM89 01-07 8510316 Neutral start switch kit, high force 1
Order code: LG
M14 98-42 11070306 Feedback link 1
M26 98-42 144725 (9004105-0110) O-ring 1
M27 98-42 042507 (9006300-0044) Retaining ring 1
M72 98-42 040642 (9003513-0800) Nut 1
M75 98-42 505022 Control manifold 1
M76 98-42 11127986 Solenoid valve assembly, 2-pole, 12 volt 1
M77 98-42 8800882 Manifold gasket 1
M78 98-42 693341 (9007314-0606) Screw 2
M90 98-42 692889 (9007314-0611) Screw 6
QM10 98-42 11015108 MDC kit, 2-pole, 12 volt 1

Parts Manual
Controls
S90 100cc pump control LR, LS

Parts configuration
(LR) (LS)
M76
QM10 QM10
M72
M71
M70
M78
*M77
M75
M90 QM89
M72 M90
M70 *M83
*M27 *M27
*M26 *M26
View A View A
*M11 *M11
View “A”
M14
T20
T70
(drain) (drain)
T30
T40
new control.

Parts Manual
Controls
Order code: LR
Model/Kit
M14 04-50 11070306 Feedback link 1
M26 04-50 144725 (9004105-0110) O-ring 1
M27 04-50 042507 (9006300-0044) Retaining ring 1
M72 04-50 040642 (9003513-0800) Nut 1
M76 04-50 521242 Solenoid valve, 12 volt, 2-pole 1
M78 04-50 693341 (9007314-0606) Screw 2
M90 04-50 692889 (9007314-0611) Screw 6
QM10 04-50 8510376 MDC kit, w/2-pole 12v solenoid 1
Order code: LS
M14 04-46 11070306 Feedback link 1
M26 04-46 144725 (9004105-0110) O-ring 1
M27 04-46 042507 (9006300-0044) Retaining ring 1
M70 04-46 8801339 Control handle, offset 1
M72 04-46 040642 (9003513-0800) Nut 1
M83 04-46 001131 (9004201-5000) O-ring 1
M90 04-46 692889 (9007314-0611) Screw 6
QM10 04-46 8510360 MDC kit, with high force neutral start switch 1
QM89 04-46 8510316 Neutral start switch kit, high force, Weather-pack 1

Parts Manual
Controls
S90 100cc pump control LW

Parts configuration
M76
QM10
M78
*M77
M75
M90
M72
M70
*M27
*M26
View A
*M11
View “A”
M14
T20
T70
(drain) (drain)
T30
T40

Parts Manual
Controls
Order code: LW
Model/Kit
M26 12-03 144725 (9004105-0110) O-ring 1
M27 12-03 042507 Retaining ring 1
M28 12-03 510690 Seal 1
M72 12-03 040642 (9003513-0800) Nut 1
M90 12-03 692889 (9007314-0611) Screw 6
QM10 12-03 11107925 MDC kit, 2-position solenoid valve, 24v 1

Parts Manual
Controls
S90P control M1, M2

Parts configuration
(M1)
(M2)
QM10
M72 QM10
M71
M70 M72
M71
M70
QM89 QM89
M90
M90
*M83
*M83
*M27
*M27 *M26
*M26
View A
View A *M11
*M11
View“A”
M14
T20
(supply) T60
T50 T70
(drain) (servo feed) T80 (drain)
T30 (servo feed)
T40

Parts Manual
Controls
Order code: M1
Model/Kit
SB-2013-011 on page 324)
M26 95-37 144725 (9004105-0110) O-ring 1
M27 95-37 042507 (9006300-0044) Retaining ring 1
M72 95-37 040642 (9003513-0800) Nut 1
M90 95-37 692889 (9007314-0611) Screw 6
QM10 95-37 11014378 MDC kit, brass sleeve 1
Order code: M2
SB-2013-011 on page 324)
M26 95-37 144725 (9004105-0110) O-ring 1
M27 95-37 042507 (9006300-0044) Retaining ring 1
M72 95-37 040642 (9003513-0800) Nut 1
M83 95-37 001131 (9004201-5000) O-ring 1
M90 95-37 692889 (9007314-0611) Screw 6
QM10 95-37 8510112 MDC kit, with neutral start switch, brass sleeve 1
QM89 95-37 80020S40 Neutral start switch kit 1

Parts Manual
Controls
S90P control M7, M8

Parts configuration
(M7) (M8)
QM10 QM10
M76 M29
M72
M71
M98
M70
QM89 *QM031
M90 M90
*M95 M72
*M83 *M96 *M97 M71
*M27
*M26 View B M70
*M27
*M26
View A
*M11
View A
*M11
M14
View“A” View“B”
T20
T50 (supply)
T70
(drain)
(servo feed) T30
T60 T40
T80
(drain)
(servo feed)

Parts Manual
Controls
Order code: M7
Model/Kit
M26 11-04 144725 (9004105-0110) O-ring 1
M27 11-04 042507 (9006300-0044) Retaining ring 1
M72 11-04 040642 (9003513-0800) Nut 1
M83 11-04 001131 (9004201-5000) O-ring 1
M90 11-04 692889 (9007314-0611) Screw 6
QM10 11-04 11099070 MDC kit, with neutral start switch 1
QM89 11-04 709014 (8510170) Neutral start switch kit 1
Order code: M8
M14 04-38 11070306 Feedback link 1
M26 04-38 144725 (9004105-0110) O-ring 1
M27 04-38 042507 (9006300-0044) Retaining ring 1
M29 04-38 9007315-0507 Screw 4
M72 04-38 040642 (9003513-0800) Nut 1
M76 04-38 508009 Solenoid valve 1
M90 04-38 692889 (9007314-0611) Screw 6
M95 04-38 9004105-0140 O-ring 1
M96 04-38 9004105-0140 O-ring 1
M97 04-38 9004105-0190 O-ring 1
M98 04-38 9007315-0505 Screw 4
QM10 04-38 11015110 MDC kit, w/2-position solenoid valve 1
QM031 04-38 11099647 Solenoid seal kit 1

Parts Manual
Controls
S90P control M9
Parts configuration
QM10
M72
M90 M71
M70
*M27
*M26
View A
*M11
View“A”
M14
T20
(supply) T60
T50
T40

Parts Manual
Controls
Order code: M9
Model/Kit
SB-2013-011 on page 324)
M26 91-07 144725 (9004105-0110) O-ring 1
M27 91-07 042507 (9006300-0044) Retaining ring 1
M72 91-07 040642 (9003513-0800) Nut 1
M90 91-07 692889 (9007314-0611) Screw 6
QM10 91-07 8510288 MDC kit 1

Parts Manual
Controls
S90P control MA, MB

Parts configuration
(MA) (MB)
QM10
QM10
M72
M71
M72 M70
M90 M71
QM89
M70
M90
*M27
*M26
*M83
*M27
*M26
View A
View A
*M11
*M11
View“A”
M14
T20
(supply) T60
T50
T40

Parts Manual
Controls
Order code: MA
Model/Kit
SB-2013-011 on page 324)
M26 87-02 144725 (9004105-0110) O-ring 1
M27 87-02 042507 (9006300-0044) Retaining ring 1
M72 87-02 040642 (9003513-0800) Nut 1
M90 87-02 692889 (9007314-0611) Screw 6
QM10 87-02 8102M0MA-A MDC kit 1
Order code: MB
SB-2013-011 on page 324)
M26 87-02 144725 (9004105-0110) O-ring 1
M27 87-02 042507 (9006300-0044) Retaining ring 1
M72 87-02 040642 (9003513-0800) Nut 1
M83 87-02 001131 (9004201-5000) O-ring 1
M90 87-02 692889 (9007314-0611) Screw 6
QM10 87-02 8102M0MB-A MDC kit with neutral start switch 1

Parts Manual
Controls
S90P control MC, MD

Parts configuration
(MC) (MD)
QM10
M76 QM10
M76
M78
M78 *M77 M72
M72 M75
*M77
M75 M71 M90 M71
M90
M70 QM89 M70
*M83
M27 M27
M26 M26
View A View A
*M11 *M11
View“A”
M14
T20
(supply) T60
T50 T70
(drain) (servo feed) T80 (drain)
T30 (servo feed)
T40

Parts Manual
Controls
Order code: MC
Model/Kit
SB-2013-011 on page 324)
M26 87-02 144725 (9004105-0110) O-ring 1
M27 87-02 042507 (9006300-0044) Retaining ring 1
M72 87-02 040642 (9003513-0800) Nut 1
M75 87-02 505022 Control manifold (SB-1995-003 on page 284) 1
M76 87-02 11127987 Solenoid valve, 12 volt, single pole 1
M78 95-10 693341 (9007314-0606) Screw (SB-1995-003 on page 284) 2
M78 87-02 95-09 041160 (9007314-0605) Screw 2
M90 87-02 692889 (9007314-0611) Screw 6
QM10 87-02 8102M0MC-A MDC kit w/12 volt solenoid, single pole 1
Order code: MD
M14 02-16 11070306 Feedback link 1
M26 02-16 144725 (9004105-0110) O-ring 1
M27 02-16 042507 (9006300-0044) Retaining ring 1
M72 02-16 040642 (9003513-0800) Nut 1
M76 02-16 11127986 Solenoid valve, 12v, double pole 1
M78 02-16 693341 (9007314-0606) Screw 2
M83 02-16 001131 (9004201-5000) O-ring 1
M90 02-16 692889 (9007314-0611) Screw 6
QM10 02-16 8102M0MD-A MDC kit, w/double pole 12v solenoid 1
QM89 02-16 8510027 Neutral start switch kit, high force, Weather-pack 1

Parts Manual
Controls
S90 100cc pump control ME, MH

Parts configuration
(ME) (MH)
QM10 QM10
M76 M29
M72
M98 M70
*M27
*QM031 M90 *M029
*M28
M90 *M26
*M95 M72
*M96 *M97 M71
View B M70
*M27
View A
*M26
*M11
View A
*M11
M14
View “A” View “B”
T20
T50 (supply)
(drain) T70
(servo feed) T30
T80 T60 T40

(servo feed) (drain)
new control.
Generic swashplate shown.

Parts Manual
Controls
Order code: ME
Model/Kit
SB-2013-011 on page 324)
M26 87-02 144725 (9004105-0110) O-ring 1
M27 87-02 042507 (9006300-0044) Retaining ring 1
M29 87-02 9007315-0510 Screw 4
M72 87-02 040642 (9003513-0800) Nut 1
M76 87-02 519357 Solenoid valve, 12 volt 1
M90 87-02 692889 (9007314-0611) Screw 6
M95 87-02 056713 (9004105-0140) O-ring 1
M96 87-02 056713 (9004105-0140) O-ring 1
M97 87-02 544742 (9004105-0190) O-ring 1
M98 87-02 9007315-0505 Screw 4
QM10 87-02 8102M0ME-A MDC kit w/2-position solenoid valve, 12 volt 1
QM031 87-02 11099647 Solenoid seal kit 1
Order code: MH
SB-2013-011 on page 324)
M26 87-02 144725 (9004105-0110) O-ring 1
M27 87-02 042507 Retaining ring 1
M28 87-02 510690 Shaft seal 1

M72 87-02 040642 (9003513-0800) Nut 1
M90 87-02 692889 (9007314-0611) Screw 6
QM10 87-02 8510282 MDC kit 1

Parts Manual
Controls
S90P control MK, ML

Parts configuration
QM10
M72
M71
M70
QM89
M90
*M83
*M27
*M26
View A
*M11
View“A”
M14
T20
T50 (supply) T60
T70 T80
(drain) (drain)
T30
T40

Parts Manual
Controls
Order code: MK
Model/Kit
SB-2013-011 on page 324)
M26 87-02 144725 (9004105-0110) O-ring 1
M27 87-02 042507 (9006300-0044) Retaining ring 1
M72 87-02 040642 (9003513-0800) Nut 1
M83 87-02 001131 (9004201-5000) O-ring 1
M90 87-02 692889 (9007314-0611) Screw 6
QM10 87-02 8102M0MK-A MDC kit w/wide deadband, nss 1
Order code: ML
SB-2013-011 on page 324)
M26 87-02 144725 (9004105-0110) O-ring 1
M27 87-02 042507 (9006300-0044) Retaining ring 1
M72 87-02 040642 (9003513-0800) Nut 1
M83 87-02 001131 (9004201-5000) O-ring 1
M90 87-02 692889 (9007314-0611) Screw 6
QM10 87-02 11015112 MDC kit w/wide deadband, high force nss 1

Parts Manual
Controls
S90P control MN
Parts configuration
QM10
M76 M29
M98
*QM031
M90
*M95
*M96 *M97 M72
View B M70
*M27
*M26
View A
*M11
M14
View “A” View “B”
T20
T50 (supply)
T70
(drain) (servo feed) T30
T60 T40
T80
(drain)
(servo feed)

Parts Manual
Controls
Order code: MN
Model/Kit
M14 94-02 11070306 Feedback link 1
M26 94-02 144725 (9004105-0110) O-ring 1
M27 94-02 042507 (9006300-0044) Retaining ring 1
M29 94-02 035592 Screw, M5 x 45 4
M72 94-02 040642 (9003513-0800) Nut 1
M90 94-02 692889 (9007314-0611) Screw 6
M95 94-02 056713 O-ring 1
M96 94-02 056713 O-ring 1
M97 94-02 544742 O-ring 1
M98 94-02 067686 Screw, M5 x 20 4
QM10 94-02 11087557 MDC kit w/2-position solenoid 1

Parts Manual
Controls
S90 100cc pump control MO, MS

Parts configuration
(M0) (MS)
QM10
M76 QM10
M72
M71
M70
M78 QM89
*M77
M90 M75 M72 M90
M71
QM89 M70 *M83 *M27
*M83 *M26
M27
M26
View A
*M11
View A
*M11
View“A”
M14
T20
(supply) T60
T50
T70 T80 (drain)
(drain)
T40
new control.
Generic swashplate and neutral start switch shown.

Parts Manual
Controls
Order code: MO
Model/Kit
M14 96-24 11070306 Feedback link 1
M26 96-24 144725 (9004105-0110) O-ring 1
M27 96-24 042507 (9006300-0044) Retaining ring 1
M72 96-24 040642 (9003513-0800) Nut 1
M78 96-24 090159 Screw 4
M90 96-24 692889 (9007314-0611) Screw 6
M95 96-24 011304 (9004104-0140) O-ring 3
QM10 96-24 11087558 MDC kit, reduce valve 1
Order code: MS
M14 01-07 11070306 Feedback link 1
M26 01-07 144725 (9004105-0110) O-ring 1
M27 01-07 042507 (9006300-0044) Retaining ring 1
M72 01-07 040642 (9003513-0800) Nut 1
M83 01-07 001131 (9004201-5000) O-ring 1
M90 01-07 692889 (9007314-0611) Screw 6
QM10 01-07 8510287 MDC kit, high force neutral start switch 1

Parts Manual
Controls
S90 100cc pump control MT, MU

Parts configuration
(MT) (MU)
QM10
M76 QM10
M76
M78
M78 *M77 M72
M72 M75
*M77 M71
M75 M71 M90
M90 QM89 M70
M70
*M83
M27
M27
M26
M26
View A
View A
*M11
*M11
View“A”
M14
T20
T50 (supply) T60
(drain) T70 T80
(drain)
T40
new control.

Parts Manual
Controls
Order code: MT
Model/Kit
M14 01-01 11070306 Feedback link 1
M26 01-01 144725 (9004105-0110) O-ring 1
M27 01-01 042507 (9006300-0044) Retaining ring 1
M72 01-01 040642 (9003513-0800) Nut 1
M76 01-01 11127986 Solenoid valve, 12 volt, 2-pole 1
M78 01-01 693341 (9007314-0606) Screw 2
M90 01-01 692889 (9007314-0611) Screw 6
QM10 01-01 8510320 MDC kit, w/2-pole 12v solenoid 1
Order code: MU
M11 94-05 14-33 8800923 Control gasket 1
M14 96-40 14-33 11070306 Feedback link (SB-1999-019 on page 298 & 1
SB-2013-011 on page 324)
M26 94-05 14-33 144725 (9004105-0110) O-ring 1
M27 94-05 14-33 042507 (9006300-0044) Retaining ring 1
M70 94-05 14-33 9800916 Control handle 1
M71 94-05 14-33 689018 (9009660-3100) Toothlock washer 1
M72 94-05 14-33 040642 (9003513-0800) Nut 1
M75 94-05 14-33 505022 Control manifold 1
M76 94-05 14-33 11127986 Solenoid valve, 12v, double pole 1
M77 94-05 14-33 8800882 Manifold gasket 1
M78 94-05 14-33 693341 (9007314-0606) Screw 2
M83 94-05 14-33 001131 (9004201-5000) O-ring 1
M90 94-05 14-33 692889 (9007314-0611) Screw 6
QM10 94-05 14-33 11019664 MDC kit, w/double pole 12v solenoid 1
QM89 94-05 14-33 8510170 Neutral start switch kit 1
QM210 94-05 14-33 11100031 Control seal kit 1

Parts Manual
Controls
S90 100cc pump control MV, MY

Parts configuration
(MV) (MY)
QM10
QM10
M72
M71
M70 M72
QM89 M90
M70
M90 *M27
*M26
*M83 *M27
*M26
*M11
View A
*M11
View “A”
M14
T20
T50 (supply) T60
T40
new control.

Parts Manual
Controls
Order code: MV
Model/Kit
SB-2013-011 on page 324)
M72 94-30 040642 (9003513-0800) Nut 1
M83 94-30 001131 (9004201-5000) O-ring 1
M90 94-30 692889 (9007314-0611) Screw 6
QM10 94-30 8510342 MDC kit, nss w/weather pack connector, 2-way 1
QM89 94-30 8510170 Neutral start switch kit, weather pack connector, 1
2-way
Order code: MV
SB-2013-011 on page 324)
M72 94-30 040642 (9003513-0800) Nut 1
M83 94-30 001131 (9004201-5000) O-ring 1
M90 94-30 692889 (9007314-0611) Screw 6
QM10 94-30 8510342 MDC kit, nss w/weather pack connector, 2-way 1
QM89 94-30 8510170 Neutral start switch kit, weather pack connector, 1
2-way

Parts Manual
Controls
S90 100cc pump control NA

Parts configuration
QM10
M90 M72
M70
*M27
*M26
M51
View A
*M11
M14
T20
T70 (supply) T80
T30
T40
new control.

Parts Manual
Controls
Order code: NA
Model/Kit
SB-2013-011 on page 324)
M26 94-30 144725 (9004105-0110) O-ring 1
M27 94-30 9006300-0044 Retaining ring 1
M51 94-30 345462 Nut 1
M70 94-30 769075 Control handle, sharp bend 1
M72 94-30 040642 (9003513-0800) Nut 1
M90 94-30 9007314-0614 Screw 6
QM10 94-30 8102M0NA-A MDC kit, NL 1

Parts Manual
Controls
S90P control NU
Parts configuration
QM10
M75
M29
M76
*M77
M72
QM89 M70
M90 *M83
*M27
*M26
M51
View A
*M11
M14
T20
T70 (supply) T80
T30
T40

Parts Manual
Controls
Order code: NU
Model/Kit
SB-2013-011 on page 324)
M26 94-05 144725 (9004105-0110) O-ring 1
M27 94-05 042507 (9006300-0044) Retaining ring 1
M29 94-05 692889 (9007314-0611) Screw 2
M51 94-05 345462 Nut 1
M72 94-05 040642 (9003513-0800) Nut 1
M75 94-05 500147 Control manifold assembly 1
M76 94-05 8700100 Solenoid valve 1
M83 94-05 784686 (9004104-0130) O-ring 1
M90 94-05 9007314-0614 Screw 6
QM10 94-05 11015114 MDC kit, NL w/nss 1
QM89 94-05 11087773 Back-up alarm switch kit 1

Parts Manual
Controls
S90P 100cc control PA, PB

Parts configuration
(PA & PB) (PE)
QM036 QM76
QM10 QM10
M76
M9 *QM034 QM037
*M658
M29 M29
M90 *M97 M9
*M96
M90
*M95
*M96
*M51
*M11 *M51
*M11
M14
View “A”
T20
(supply)
T50 T60
(drain) T70 T80
(drain)
T40

Parts Manual
Controls
Order code: PA
Model/Kit
M9 94-07 782037 PDC, 12 volt 1
SB-2013-011 on page 324)
M29 94-07 035592 Screw 4
M51 94-07 9003509-0008 Seal nut 1
M76 94-07 11001795 Solenoid, 12 volt, Din connector 2
M90 94-07 692889 (9007314-0611) Screw 6
M95 94-07 011296 (9004105-0120) O-ring 2
M96 94-07 688721 (9004104-0170) O-ring 1
M97 94-07 314534 (9004104-0310) O-ring 1
M658 94-07 635938 (9004100-0210) O-ring 2
QM10 94-07 11087561 HDC2, w/PDC 1
Order code: PB
M9 94-15 782045 PDC, 24 volt 1
SB-2013-011 on page 324)
M29 94-15 035592 Screw 4
M51 94-15 9003509-0008 Seal nut 1
M76 94-15 11001794 Solenoid, 24 volt, Din connector 2
M90 94-15 692889 (9007314-0611) Screw 6
M95 94-15 011296 (9004105-0120) O-ring 2
M96 94-15 688721 (9004104-0170) O-ring 1
M97 94-15 314534 (9004104-0310) O-ring 1
M658 94-15 635938 (9004100-0210) O-ring 2
QM10 94-15 11034093 Electro-hydraulic control kit 1

Parts Manual
Controls
S90P control PE
Parts configuration
(PA & PB) (PE)
QM036 QM76
QM10 QM10
M76
M9 *QM034 QM037
*M658
M29 M29
M90 *M97 M9
*M96
M90
*M95
*M96
*M51
*M11 *M51
*M11
M14
View “A”
T20
(supply)
T50 T60
(drain) T70 T80
(drain)
T40

Parts Manual
Controls
Order code: PE
Model/Kit
M9 10-30 11175053 HIC, proportional reducing manifold assembly 1
M14 10-30 11070306 Feedback link 1
M29 10-30 K28807 Screw 4
M51 10-30 9003509-0008 Seal nut 1
M90 10-30 692889 (9007314-0611) Screw 6
M96 10-30 9004105-0120 O-ring 4
QM10 10-30 8510286 EDC, high current, 3-11 bar, 12 volt 1
QM036 10-30 11175054 Coil nut 2
QM037 10-30 322466 Coil, 12 volt 2
QM76 10-30 138108 Solenoid valve, 12 volt 2

Parts Manual
Controls
S90 100cc pump control PF-PJ

Parts configuration
(PF) (PH & PJ)
QM76
QM10 QM036
QM10
M76
M9
QM037
*M658 M29
*QM034
M29 M9
M90 *M97
*M96
M90
*M95
*M96
*M51
*M11 *M51
*M11
View“A”
M14
T20
(supply) T60
T50 T80
T70 (drain)
(drain) (servo feed)
(servo feed) T30
T40
new control.

Parts Manual
Controls
Order code: PF
Model/Kit
M9 03-32 519719 PDC, 12 volt 1
M29 03-32 035592 Screw 4
M51 03-32 9003509-0008 Seal nut 1
M76 03-32 11001793 Solenoid, 12 volt, AMP connector 2
M90 03-32 692889 (9007314-0611) Screw 6
M95 03-32 011296 (9004105-0120) O-ring 2
M96 03-32 688721 (9004104-0170) O-ring 1
M97 03-32 314534 (9004104-0310) O-ring 1
M658 03-32 635938 (9004100-0210) O-ring 2
QM10 03-32 11087592 EDC2, 12 volt, AMP connector 1
Order code: PH
M9 12-38 11120541 Reducing manifold 1
M29 12-38 K28807 Screw 4
M51 12-38 9003509-0008 Seal nut 1
M90 12-38 692889 (9007314-0611) Screw 6
M96 12-38 011296 (9004105-0120) O-ring 4
QM10 12-38 11121734 EDC2, 12 volt, AMP connector 1
QM036 12-38 11117349 Coil nut 2
QM037 12-38 171180419 Coil, 12 volt 2
Order code: PJ
M9 14-15 11175061 Reducing manifold 1
M29 14-15 K28807 Screw 4
M51 14-15 9003509-0008 Seal nut 1
M90 14-15 692889 (9007314-0611) Screw 6
M96 14-15 011296 (9004105-0120) O-ring 4
QM10 14-15 11141118 EDC2, 24 volt 1
QM036 14-15 11175058 Coil nut 2
QM037 14-15 11175074 Coil, 24 volt 2

Parts Manual
Controls
S90P control RR, RS

Parts configuration
QM10
(RR) (RS & RU)
M72 M72
M70 M70
M76
M92
*M27
*M029
*M28
M90 *M26
QM89
*QM83
View A
*M11
M14 View “A”
T20
T70 (supply) T80
T30
T40

Parts Manual
Controls
Order code: RR
Model/Kit
M26 99-06 144725 (9004105-0110) O-ring 1
M27 99-06 042507 (9006300-0044) Retaining ring 1
M28 99-06 510690 Lip seal 1
M72 99-06 040642 (9003513-0800) Nut 1
M90 99-06 354407 Screw 5
M92 99-06 510382 Screw 1
QM10 99-06 8510245 MDC kit, roller 1
QM83 99-06 001131 (9004201-5000) O-ring 1
QM89 99-06 11099847 Neutral start switch, high force 1
Order code: RS
M26 01-15 144725 (9004105-0110) O-ring 1
M27 01-15 042507 (9006300-0044) Retaining ring 1
M28 01-15 510690 Lip seal 1
M72 01-15 040642 (9003513-0800) Nut 1
M90 01-15 354407 Screw 5
M92 99-06 510382 Screw 1
QM10 01-15 11087610 MDC kit, roller 1
QM83 01-15 001131 (9004201-5000) O-ring 1

Parts Manual
Controls
S90P control RU
Parts configuration
QM10
(RR) (RS & RU)
M72 M72
M70 M70
M76
M92
*M27
*M029
*M28
M90 *M26
QM89
*QM83
View A
*M11
M14 View “A”
T20
T70 (supply) T80
T30
T40

Parts Manual
Controls
Order code: RU
Model/Kit
M26 97-30 144725 (9004105-0110) O-ring 1
M27 97-30 042507 (9006300-0044) Retaining ring 1
M28 97-30 510690 Lip seal 1
M72 97-30 040642 (9003513-0800) Nut 1
M90 97-30 354407 Screw 5
M92 99-06 510382 Screw 1
QM10 97-30 11087609 MDC kit, roller 1
QM83 97-30 001131 (9004201-5000) O-ring 1

Parts Manual
Controls
S90P control SA-SE

Parts configuration
M90
View A
M11
View“A”
M14
T70 T80
Possible orifice locations

Parts Manual
Controls
Order code: SA
Model/Kit
M11 07-23 8800923 Gasket 1
M14 07-23 11070306 Feedback link 1
M90 07-23 694356 (9007314-0608) Screw 6
Order code: SB
M11 07-23 8800923 Gasket 1
M14 07-23 11070306 Feedback link 1
M90 07-23 694356 (9007314-0608) Screw 6
Order code: SD
M11 10-34 8800923 Gasket 1
M14 10-34 11070306 Feedback link 1
M90 10-34 694356 (9007314-0608) Screw 6
Order code: SE
M11 10-34 8800923 Gasket 1
M14 10-34 11070306 Feedback link 1
M90 10-34 694356 (9007314-0608) Screw 6

Parts Manual
Filtration
S90 100cc pump filtration 0-9

Parts configuration
(3)
(0)
N01
N01
N40
N20
*N15 N35 N20
N45 N36
*N15
N36
(6)
N01
N40
N35 N20
*N15
N36
N32
(9)
(7)
N01
N97
N43
N97 N41
N01
N98
N98
N81
N20 N80
N43
N20 N82
N42 N95 N83
N95
N30 N84
QN40 QN40

Parts Manual
Filtration
Order code: 0
Model/Kit
N01 08-01 11060431 Filter manifold assembly 1
N15 08-01 001172 (9004201-9000) O-ring 1
N20 08-01 11049997 Nut 1
N36 08-01 8700127 Diagnostic receptacle 1
N45 08-01 8700128 Dust cover 1
Order code: 3
N15 99-18 001172 (9004201-9000) O-ring 1
N20 99-18 11049997 Nut 1
N35 99-18 140644 (9005100-5600) Plug assembly 1
N36 99-18 140644 (9005100-5600) Plug assembly 1
QN40 99-18 11004919 Filter, long 1
Order code: 6
N15 00-01 001172 (9004201-9000) O-ring 1
N20 00-01 11049997 Nut 1
N32 00-01 140644 (9005100-5600) Plug assembly 1
N35 00-01 140644 (9005100-5600) Plug assembly 1
N36 00-01 140644 (9005100-5600) Plug assembly 1
QN40 00-01 11004917 Filter, short 1
Order code: 7
N20 02-03 360768 Check valve 1
N30 02-03 365965 Plug assembly 1
N41 02-03 9005100-8700 Plug assembly 1
N95 02-03 500115 Washer 2
N97 02-03 376269 Screw 4
N98 02-03 9004104-0320 O-ring 1
QN40 02-03 11004919 Filter, long 1
Order code: 8
No parts

Parts Manual
Filtration
Parts configuration
(3)
(0)
N01
N01
N40
N20
*N15 N35 N20
N45 N36
*N15
N36
(6)
N01
N40
N35 N20
*N15
N36
N32
(9)
(7)
N01
N97
N43
N97 N41
N01
N98
N98
N81
N20 N80
N43
N20 N82
N42 N95 N83
N95
N30 N84
QN40 QN40

Parts Manual
Filtration
Order code: 9
Model/Kit
N20 02-03 520974 Check valve 1
N80 02-03 518331 Magnetic piston 1
N81 02-03 519585 Spring 1
N83 02-03 11031853 Filtration sensor 1
N84 02-03 519968 Screw 2
N95 02-03 042515 Retaining ring 1
N97 02-03 393603 Screw 4
N98 02-03 9004104-0320 O-ring 1
QN40 02-03 11004919 Filter, long 1

Parts Manual
Filtration
S90 100cc pump filtration A-L

Parts configuration
(A & E) (G)
N97 N41
N01
QN01
QN40
N98
N20 N43
N35 N20
*N15 N42
N35 N95
N30
N36
N36
QN40
(J)
N70
(L)
N75 N01
N71
N90 QN01
N80
QN40
N97
N43 N20
N35
*N15
N35
N98 N36
N36
N42 N20
N95
N60
N30 QN40

Parts Manual
Filtration
Order code: A
Model/Kit
N15 02-41 001172 (9004201-9000) O-ring 1
N20 02-41 11049997 Nut 1
N35 02-41 140644 (9005100-5600) Plug assembly 1
N36 02-41 140644 (9005100-5600) Plug assembly 1
QN01 02-41 11145249 Filter manifold assembly 1
QN40 02-41 11004917 Filter, short 1
Order code: E
N15 96-46 001172 (9004201-9000) O-ring 1
N20 96-46 11049997 Nut 1
N35 96-46 140644 (9005100-5600) Plug assembly 1
N36 96-46 140644 (9005100-5600) Plug assembly 1
QN40 96-46 11004917 Filter, short 1
Order code: G
N20 96-46 360768 Check valve 1
N41 96-46 Plug assembly 1
N42 96-46 140644 (9005100-5600) Plug assembly 1
N43 96-46 140644 (9005100-5600) Plug assembly 1
N95 96-46 500115 Waher 2
N97 96-46 376269 Screw 4
N98 96-46 9004104-0320 O-ring 1
QN40 96-46 11004917 Filter, short 1

Parts Manual
Filtration
Parts configuration
(A & E) (G)
N97 N41
N01
QN01
QN40
N98
N20 N43
N35 N20
*N15 N42
N35 N95
N30
N36
N36
QN40
(J)
N70
(L)
N75 N01
N71
N90 QN01
N80
QN40
N97
N43 N20
N35
*N15
N35
N98 N36
N36
N42 N20
N95
N60
N30 QN40

Parts Manual
Filtration
Order code: J
Model/Kit
N20 96-46 360768 Check valve 1
N42 96-46 140644 (9005100-5600) Plug assembly 1
N43 96-46 140644 (9005100-5600) Plug assembly 1
N60 96-46 500114 Dust indication 1
N71 96-46 347419 Wax element 1
N75 96-46 001149 (9004201-6200) O-ring 1
N80 96-46 502224 Spring 1
N90 96-46 502240 Poppet 1
N95 96-46 500115 Washer 2
N97 96-46 376269 Screw 4
N98 96-46 9004104-0320 O-ring 1
QN40 96-46 11004917 Filter, short 1
Order code: L
N15 87-02 001172 (9004201-9000) O-ring 1
N20 95-18 11049997 Nut (SB-1994-036) 1
N20 87-02 95-17 700492 (9002863-1600) Nut 1
N35 87-02 140644 (9005100-5600) Plug assembly 1
N36 87-02 140644 (9005100-5600) Plug assembly 1
QN40 87-02 11004919 Filter, long 1

Parts Manual
Filtration
S90 100cc pump filtration P-X

Parts configuration
(P) (R)
QN01
N01
QN40
N20
N20 *N15
N35 N36
*N15
N35
N36
N36
(S) (U)
N01
N37 *N15
N20
*N15
N10
N45 N36
(W) (X)
QN01
N87
QN40
N37
N20
N35
*N15 *N15
N35
N36
N36
N10

Parts Manual
Filtration
Order code: P
Model/Kit
N15 87-02 001172 (9004201-9000) O-ring 1
N20 95-18 11049997 Nut (SB-1994-36 on page 283) 1
N20 87-02 95-17 700492 (9002863-1600) Nut 1
N35 87-02 140644 (9005100-5600) Plug assembly 1
N36 87-02 140644 (9005100-5600) Plug assembly 1
QN40 87-02 11004917 Filter, short 1
Order code: R
N15 87-02 001172 (9004201-9000) O-ring 1
N20 95-18 11049997 Nut (SB-1994-36 on page 283) 1
N20 87-02 95-17 700492 (9002863-1600) Nut 1
N36 87-02 140644 (9005100-5600) Plug assembly 1
Order code: S
N10 87-02 5000230 Reducer assembly 1
N15 87-02 001172 (9004201-9000) O-ring 1
N37 87-02 140644 (9005110-5600) Plug assembly 1
Order code: U
N15 96-16 001172 (9004201-9000) O-ring 1
N20 96-16 11049997 Nut 1
N45 96-16 8700128 Dust cover 1
Order code: V
No parts

Parts Manual
Filtration
Parts configuration
(P) (R)
QN01
N01
QN40
N20
N20 *N15
N35 N36
*N15
N35
N36
N36
(S) (U)
N01
N37 *N15
N20
*N15
N10
N45 N36
(W) (X)
QN01
N87
QN40
N37
N20
N35
*N15 *N15
N35
N36
N36
N10

Parts Manual
Filtration
Order code: W
Model/Kit
N10 87-02 5000230 Reducer assembly 1
N15 87-02 001172 (9004201-9000) O-ring 1
N87 08-01 8700128 Dust cover 1
Order code: X
N15 01-01 001172 (9004201-9000) O-ring 1
N20 01-01 11049997 Nut 1
N35 01-01 9005100-5600 Plug assembly 1
N36 01-01 9005100-5600 Plug assembly 1
QN40 01-01 11004919 Filter, long 1

Parts Manual
S90 100cc pump high pressure protection 1-7, A-F

Parts configuration
Twin ported Side ported Twin ported Side ported
end cap end cap end cap end cap
P80 P80 P80

P70
P70 P70 P80
P80 P80
P70
P80 P80
P70 P70 P70
P70
View “A” with View “A” with
pressure limiters, pressure limiters,
CCW rotation CW rotation
Options 1, 5, 6 & F Options 1, 5, 6 & F

P80 P70 P80

P80 P80
P70
P80 P70 P80
P70
P80 P80 P80 P80 P80
P80
View “A” without View “A” with pressure
pressure limiters, limiter port A only,
CCW/CW hand rotation CW rotation
Option 2 & 7 Option B

QPA2B
(1-7, B, D, F)
View “A”
*P02
QPA2A
*P06
(A) *P13
*P02
QPA2B
*P06
*P13
*P02
*P06
*P13
*P02
QPA2A *P06
*P13
Generic end cap used to show part location only.

Parts Manual
Common parts
Model/Kit
P02 87-02 688721 (9004104-0170) O-ring 2
P06 87-02 071811 O-ring 2
P13 87-02 544742 (9004105-0190) O-ring 2
Order code: 1
P70 87-02 8800188 Check valve 2
P80 87-02 9005475-0004 Special plug assembly 2
QPA2A 87-02 8510022-1 Multi-function valve kit 1
QPA2B 87-02 8510022-1 Multi-function valve kit 1
Order code: 2
P70 87-02 327007 (9005110-4400) Plug (SB-1989-003 on page 264) 1
Order code: 4
Order code: 5
P70 87-02 8800188 Check valve 2
QPA2A 87-02 8510240 Multi-function valve kit 1
QPA2B 87-02 8510240 Multi-function valve kit 1
Order code: 6
P70 87-02 8800188 Check valve 2

Parts Manual
Parts configuration
P80 P80 P80

P70
P70 P70 P80
P80 P80
P70
P80 P80
P70 P70 P70
P70
CCW rotation CW rotation
Options 1, 5, 6 & F Options 1, 5, 6 & F

P80 P70 P80

P80 P80
P70
P80 P70 P80
P70
P80 P80 P80 P80 P80
P80
View “A” without View “A” with pressure
pressure limiters, limiter port A only,
CCW/CW hand rotation CW rotation
Option 2 & 7 Option B

QPA2B
(1-7, B, D, F)
View “A”
*P02
QPA2A
*P06
(A) *P13
*P02
QPA2B
*P06
*P13
*P02
*P06
*P13
*P02
QPA2A *P06
*P13
Generic end cap used to show part location only.

Parts Manual
Order code: 7
Model/Kit
P70 87-02 327007 (9005110-4400) Plug (SB-1989-003 on page 264) 1
Order code: A
QPA2A 87-02 8510202 Multi-function valve kit, 420 bar 1
QPA2B 87-02 8510202 Multi-function valve kit, 420 bar 1
Order code: B
P70 95-22 8800188 Check valve 1
Order code: D
Order code: F
P70 04-36 8800188 Check valve 2

Parts Manual
S90 100cc pump high pressure protection G-P

Parts configuration
P70
P80 P80 P80
P70 P80
P70 P80 P80
P70
P80
P80 P70 P70
P70 P70
CCW rotation, CW rotation,
Options G, H, K & P Options G, H, K & P
QPA2B
Twin and side (G, K, L, M, P)
ported end cap
*P02 View “A”
QPA2A
*P06
P70 *P13
*P02
P70
View “A” with *P06
pressure limiters, *P13
CW rotation,
Options L & M
QPA2B
QPA2B
QPA2A (H)
(J) *P02 View “A”

*P21
*P21 *P20
*P20
*P06
*P13
*P02
*P02
*P21
*P20 *P06
*P06 *P13
*P13
*P02
QPA2A *P06
*P13
Generic end caps used to show valve locations only.

Parts Manual
Common parts
Model/Kit
P02 87-02 688721 (9004104-0170) O-ring 2
P06 87-02 071811 O-ring 2
P13 87-02 544742 (9004105-0190) O-ring 2
Order code: G
P70 97-06 8800188 Check valve 2
P80 97-06 9005475-0004 Special plug 2
Order code: H
P20 97-40 9004105-0160 O-ring 1
P21 97-40 9006110-0160 Back up ring 1
P70 97-40 8800188 Check valve 2
P80 97-40 9005475-0004 Special plug 2
Order code: J
P20 97-06 9004105-0160 O-ring 2
P21 97-06 9006110-0160 Back up ring 2
Order code: K
P70 97-26 8800188 Check valve 2
P80 97-26 9005475-0004 Special plug 2

Parts Manual
Parts configuration
P70
P80 P80 P80
P70 P80
P70 P80 P80
P70
P80
P80 P70 P70
P70 P70
CCW rotation, CW rotation,
Options G, H, K & P Options G, H, K & P
QPA2B
Twin and side (G, K, L, M, P)
ported end cap
*P02 View “A”
QPA2A
*P06
P70 *P13
*P02
P70
View “A” with *P06
pressure limiters, *P13
CW rotation,
Options L & M
QPA2B
QPA2B
QPA2A (H)
(J) *P02 View “A”

*P21
*P21 *P20
*P20
*P06
*P13
*P02
*P02
*P21
*P20 *P06
*P06 *P13
*P13
*P02
QPA2A *P06
*P13

Parts Manual
Order code: L
Model/Kit
P70 97-26 8800188 Check valve 2
Order code: M
P70 98-11 8800188 Check valve 2
Order code: P
P70 04-47 8800188 Check valve 2
P80 04-47 9005475-0004 Special plug 2

Parts Manual
S90 100cc pump high pressure protection R, T

Parts configuration
PA2B (R)
*P06
View “A” Side ported
end cap
QPA2A
*P13
P80
P80
*P02
P70
P80
*P06
*P13 P70N
View “A” of end cap
with pressure limiter port A,
CCW rotation.
Option R
(T)
Twin ported Side ported
end cap end cap
P80 P80
P70 P70
P80 Twin ported Side ported

P80
P70 P70 end cap end cap
View “A” with P70
QPA2B pressure limiters,
CCW rotation, P80
P80
Option T P80 P80
P70
*P21 P70 P70
*P20 View “A” with
pressure limiters,
CW rotation,
*P02
Option T
View “A”
*P21
*P20
*P06
*P13
*P02
QPA2A *P06
*P13

Parts Manual
Order code: R
Model/Kit
P02 99-14 141564 (9004100-0170) O-ring 1
P06 99-14 000836 (9004100-0200) O-ring 2
P13 99-14 544742 (9004105-0190) O-ring 2
P70 99-14 8800188 Check valve 1
P70N 99-14 327007 (9005110-4400) Plug assembly 1
P80 99-14 9005475-0004 Special plug 3
PA2B 99-14 781971 Plug assembly 1
Order code: T
P02 00-35 141564 (9004100-0170) O-ring 2
P06 00-35 000836 (9004100-0200) O-ring 2
P13 00-35 544742 (9004105-0190) O-ring 2
P20 00-35 9004105-0160 O-ring 2
P21 00-35 9006110-0160 Back up ring 2
P70 00-35 8800188 Check valve 2
P80 00-35 9005475-0004 Special plug 2

Parts Manual
S90 100cc pump high pressure protection V, Z

Parts configuration
Twin ported
CCW rotation
end cap
(V)
QPA2B
P70
*P02
QPA2A
P70
*P06
*P13 View “A” of end cap
*P02 Option V
*P06
*P13 Twin ported
CW rotation
end cap
P70
P70

Option V
(Z)
QPA2B
View “A”
Twin ported
*P02 CW rotation
QPA2A
end cap
*P06
*P13
*P02
P70
*P06
*P13
P70

Option Z

Parts Manual
Common parts
Model/Kit
P02 87-02 141564 (9004100-0170) O-ring 2
P06 87-02 000836 (9004100-0200) O-ring 2
P13 87-02 544742 (9004105-0190) O-ring 2
Order code: V
P70 08-30 8800188 Check valve 2
Order code: Z
P70 04-12 8800188 Check valve 2

Parts Manual
Orifice
S90 100cc pump orifice 01-26

Parts configuration
(01-06, 09, 022)
T20
T30
T40
See control drawing

for orifice location
(21, 26)
T70 T80
T20
T30
T40
See control drawing

(23)
T50 T60
T20
T30
T40
See control drawing


Parts Manual
Orifice
Order code: 01
Model/Kit
T20 87-42 8801136 Orifice check valve, .018” 1
T30 87-42 679506 (8700007) Spring 1
T40 87-42 8801303 Spring retainer 1
Order code: 02
T30 87-42 679506 (8700007) Spring 1
Order code: 03
T30 87-42 679506 (8700007) Spring 1
Order code: 04
T30 87-42 679506 (8700007) Spring 1
Order code: 05
T30 87-42 679506 (8700007) Spring 1
Order code: 06
T30 87-42 679506 (8700007) Spring 1
Order code: 09
T30 87-42 679506 (8700007) Spring 1

Parts Manual
Orifice
Parts configuration
(01-06, 09, 022)
T20
T30
T40
See control drawing

(21, 26)
T70 T80
T20
T30
T40
See control drawing

(23)
T50 T60
T20
T30
T40
See control drawing


Parts Manual
Orifice
Order code: 21
Model/Kit
T30 87-42 679506 (8700007) Spring 1
T70 87-42 714477 Orifice plug, 0.8mm, M8 x 8 1
Order code: 22
T30 87-42 679506 (8700007) Spring 1
Order code: 23
T30 87-42 679506 (8700007) Spring 1
Order code: 26
T30 87-42 679506 (8700007) Spring 1
T50 87-42 598292 (11062004) Orifice plug, 0.8mm, M5 x 6 1

Parts Manual
Orifice

Parts configuration
(28, 30)
T50 T70 T80 T60

T20
T30
T40
See control drawing

(29, 44)
T50 T60 (32)

T20
T50 T60
T30
See control drawing

T40 for orifice location
See control drawing

(38, 40)
T70 T80
T20
(34)
T70 T80
T30
See control drawing

for orifice location T40
See control drawing


Parts Manual
Orifice
Order code: 28
Model/Kit
T30 87-42 679506 (8700007) Spring 1
Order code: 29
T30 87-42 679506 (8700007) Spring 1
Order code: 30
T30 87-42 679506 (8700007) Spring 1
Order code: 32
Order code 33
No parts
Order code 34

Parts Manual
Orifice
Parts configuration
(28, 30)
T50 T70 T80 T60

T20
T30
T40
See control drawing

(29, 44)
T50 T60 (32)

T20
T50 T60
T30
See control drawing

See control drawing

(38, 40)
T70 T80
T20
(34)
T70 T80
T30
See control drawing

See control drawing


Parts Manual
Orifice
Order code: 38
Model/Kit
T30 87-42 679506 (8700007) Spring 1
Order code: 40
T20 87-42 11061970 Orifice check valve, 1.02mm 1
T30 87-42 679506 (8700007) Spring 1
Order code: 44
T20 87-42 11061981 Orifice check valve, 1.37mm 1
T30 87-42 679506 (8700007) Spring 1

Parts Manual
Orifice

Parts configuration
(41)
(38, 42)
T70 T80 T50 T70 T80 T60

T20
T30
T40
See control drawing

(43)
T50 T70 T80 T60

T20
T30
T40
See control drawing

(45, 46, 49)
T50 T60
T20
T30
T40
See control drawing


Parts Manual
Orifice
Order code: 45
Model/Kit
T30 87-42 679506 (8700007) Spring 1
Order code: 46
T30 87-42 679506 (8700007) Spring 1
Order code: 49
T30 87-42 679506 (8700007) Spring 1
Order code: 50
T30 87-42 679506 (8700007) Spring 1
Order code: 64

Parts Manual
Orifice
Parts configuration
(28, 30)
T50 T70 T80 T60

T20
T30
T40
See control drawing

(29, 44)
T50 T60 (32)

T20
T50 T60
T30
See control drawing

See control drawing

(38, 40)
T70 T80
T20
(34)
T70 T80
T30
See control drawing

See control drawing


Parts Manual
Orifice
Order code: 76
Model/Kit
T30 87-42 679506 (8700007) Spring 1
Order code: 77
No parts
Order code: 82
Order code: 84
Order code: 99
T30 87-42 679506 (8700007) Spring 1

Parts Manual
Orifice
S90 100cc pump orifice A3-C1

Parts configuration
(A3)
T50 T60
T20 (A4)
T70 T80
T30
See control drawing

T40
See control drawing

(A5, A8, C1) (B1, B7, B8, B9)

T70 T80
T20 T50
T30 See control drawing

T40
See control drawing

(B3, BB)
T50 T70 T80
See control drawing


Parts Manual
Orifice
Order code: A3
Model/Kit
T30 87-42 679506 (8700007) Spring 1
Order code: A4
Order code: A5
T20 87-42 11061970 Orifice check valve, 0.40” 1
T30 87-42 679506 (8700007) Spring 1
Order code: A8
T30 87-42 679506 (8700007) Spring 1
Order code: B1
T50 87-42 507042 Orifice plug, 1.5 mm, M6 x 8 1
Order code: B2

Parts Manual
Orifice
Parts configuration
(A3)
T50 T60
T20 (A4)
T70 T80
T30
See control drawing

T40
See control drawing

(A5, A8, C1) (B1, B7, B8, B9)

T70 T80
T20 T50
T30 See control drawing

T40
See control drawing

(B3, BB)
T50 T70 T80
See control drawing


Parts Manual
Orifice
Order code: B3
Model/Kit
Order code: B7
Order code: B8
Order code: B9
Order code: BB
Order code: C1
T30 87-42 679506 (8700007) Spring 1

Parts Manual
Orifice
S90 100cc pump orifice C3-GD

Parts configuration
(C3, C5, C6, C7)
(C4)
T50 T60
T20
T50 T60
T30
See control drawing
T40
See control drawing

(G4, G8, GB, GD)
T50
(G1) T20
T50
T30
See control drawing

T40
See control drawing


Parts Manual
Orifice
Order code: C3
Model/Kit
T30 87-42 679506 (8700007) Spring 1
Order code: C4
Order code: C5
T30 87-42 679506 (8700007) Spring 1
Order code: C6
T30 87-42 679506 (8700007) Spring 1
Order code: C7
T20 87-42 11061981 Orifice check valve, 1.37 mm 1
T30 87-42 679506 (8700007) Spring 1
Order code: G1

Parts Manual
Orifice
Parts configuration
(C3, C5, C6, C7)
(C4)
T50 T60
T20
T50 T60
T30
See control drawing
T40
See control drawing

(G4, G8, GB, GD)
T50
(G1) T20
T50
T30
See control drawing

T40
See control drawing


Parts Manual
Orifice
Order code: G4
Model/Kit
T30 87-42 679506 (8700007) Spring 1
Order code: G8
T30 87-42 679506 (8700007) Spring 1
Order code: GB
T30 87-42 679506 (8700007) Spring 1
Order code: GD
T20 87-42 11061993 Control orifice kit, 1.57 mm 1
T30 87-42 679506 (8700007) Spring 1

Parts Manual
Orifice
S90 100cc pump orifice GF-Z3

Parts configuration
(GF, GJ) (H1, K2)

T50 T50 T60
T20 T20
T30 T30
T40 T40
See control drawing See control drawing

for orifice location for orifice location
(K1)
T20
(P1)
T70 T80
T30
See control drawing

T40
See control drawing

(Z3)
T70 T80
T20
T30
T40
See control drawing


Parts Manual
Orifice
Order code: GF
Model/Kit
T20 87-42 11061970 Control orifice kit, 0.040” 1
T30 87-42 679506 (8700007) Spring 1
Order code: GJ
T20 87-42 11061981 Control orifice kit, 1.37 mm 1
T30 87-42 679506 (8700007) Spring 1
Order code: H1
T30 87-42 679506 (8700007) Spring 1
Order code: K1
T20 87-42 11061981 Orifice check valve, 1.37 mm 1
T30 87-42 679506 (8700007) Spring 1
Order code: K2
T30 87-42 679506 (8700007) Spring 1
Order code: P1
Order code: Z3
T30 87-42 679506 (8700007) Spring 1

Parts Manual
Overhaul seal kit
S90 100cc pump overhaul seal kit
Overhaul seal kit

Model/Kit
Q210 87-42 11095649 Overhaul seal kit 1
B90 87-42 9803390 Control screen 3
on page 292)
E40 87-02 505412 (9003509-0008) Seal nut 2
E50 87-02 517378 (9004104-1620) O-ring 1
E60 87-02 517228 (5000206) Screw (SB-1994-018 on page 279) 6
F11 87-02 9004100-1310 O-ring 2
F12 87-02 507799 (8700067) Piston ring 2
F40 87-02 363754 (9004104-0350) O-ring 2
F50 89-41 9004104-0340 O-ring 2
F112 87-02 505412 (9003509-0008) Seal nut 1
F124 87-02 066159 Seal nut 1
F212 87-02 505412 (9003509-0008) Seal nut 1
F224 87-02 066159 Seal nut 1
G30 89-46 8200212 End cap gasket (SB-1992-003 on page 270) 1
J40 87-02 680892 (9004104-0440) O-ring 1
J50 87-02 056739 (9004104-1580) O-ring 1
K50 87-02 001149 (9004201-6200) O-ring 1
L25 87-02 521722 Seal carrier assembly (SB-2007-018 on page 311) 1
N15 87-02 001172 (9004201-9000) O-ring 1
N98 87-02 9004104-0320 O-ring 1
P02 87-02 688721 (9004104-0170) O-ring 2
P06 87-02 071811 O-ring 2
P13 87-02 544742 (9004105-0190) O-ring 2
P20 87-02 9004105-0160 O-ring 2
P21 87-02 9006110-0160 O-ring 2

Parts Manual
Service bulletin
AN152886483362
To improve efficiency and reliability, the number of parts in series 90 pumps is being reduced. The charge
pump design on 55cc - 130cc frame sizes is being changed so that the outer port plate is an integral part
of the charge pump cover and distance plates are eliminated. The change is taking effect at the following
manufacturing dates:
• 55cc: 93-10
• 75cc: 93-10
• 100cc: 93-15
• 130 cc:93-34
For auxiliary pad options, the new charge pump cover is rotation dependent. The cover will be marked as
either left hand (L) or right hand (R). The non-auxiliary pad cover is not rotation dependent.
The charge pump shaft also changes and must be replaced when using the new style hardware. The
complete charge pump assembly can be interchanged with corresponding hardware from 89-17 and
beyond. However, piece parts are not interchangeable. For units prior to 89-17, consult Danfoss.
The old design charge pump hardware is obsolete and is no longer available. Refer to the chart on the
next page to determine the replacement kit.

Parts Manual
Service bulletin
AN152886483362 charge pump replacements

The following information must be known to determine the correct charge pump replacement kit:
1. Unit size (055, 075, 100, or 130cc)
2. Charge pump displacement (11, 14, 17, 20, 26, or 34cc)
3. Auxiliary pad (Yes or No)
4. Rotation (LH or RH)
Obsoleted Charge Pump Parts Unit Size Charge pump Auxiliary pad Rotation Replacement kit
displacement
Gear Set Shaft Cover
8000169 8000174 8800513 055 11 cc No LH or RH 8510028
8800514 Yes LH 8510029
8800514 Yes RH 8510030
8000170 8000174 8800513 055 14 cc No LH or RH 8510031
8800514 Yes LH 8510032
8800514 Yes RH 8510033
8000171 8000174 8800513 055 17 cc No LH or RH 8510034
8800514 Yes LH 8510035
8800514 Yes RH 8510036
8100313 337956 8800513 075 14 cc No LH or RH 8510037
8800514 Yes LH 8510038
8800514 Yes RH 8510039
8100314 337956 8800513 075 17 cc No LH or RH 8510040
8800514 Yes LH 8510041
8800514 Yes RH 8510042
8100315 337956 8800513 075 20 cc No LH or RH 8510043
8800514 Yes LH 8510044
8800514 Yes RH 8510045
8200158 337956 8800513 100 17 cc No LH or RH 8510046
8800514 Yes LH 8510047
8800514 Yes RH 8510048
8200159 337956 8800513 100 20 cc No LH or RH 8510049
8800514 Yes LH 8510050
8800514 Yes RH 8510051
8200160 337956 8800513 100 26 cc No LH or RH 8510052
8800514 Yes LH 8510053
8800514 Yes RH 8510054
714444 303636 347518 130 20 cc No LH or RH 8510064
347526 Yes LH 8510065
347526 Yes RH 8510066
714451 303636 347518 130 26 cc No LH or RH 8510067
347526 Yes LH 8510068
347526 Yes RH 8510069
714469 303636 347518 130 34 cc No LH or RH 8510070
347526 Yes LH 8510071
347526 Yes RH 8510072

Parts Manual
Service bulletin
SB-1988-009
Products affected
Series 90 pumps
Subject
Servo arm change
Description
As a product improvement, Danfoss has changed the series 90 pump servo arm and swashplate (item
D10 and D50). The old style servo arm and swashplate will become obsolete. Because this change creates
non-interchangeability between new and old swashplates, servo arms, and possibly servo piston (item
S10) and slider block (item F20), separate servo arms and swashplates will no longer be sold as service
parts.
Also, the new servo arm is pressed into a groove in the new swashplate. This situation requires special
tooling for assembly, therefore, pre-assembled kits will be created for 55, 75, and 100 cc pumps. The kits
will work in any vintage pump.
The kit for 55 cc pumps will include all the items in the figure, except item S10
The kit for 75 cc pumps will include all items in the figure.
The kit for 100 cc pumps will include all items in the figure, except items S10 and F20.
The slider block (item F20) in 55 cc pumps and the slider block and the servo piston (item S10) in 75 cc
pumps had to be changed slightly to allow clearance for the new servo arm. The new servo piston and
slider block will work in any vintage pump.
D55 D65
S10
F12 F11 D10

D75 D60
F11 D70
F12
F20
D50
Models affected
All 94-2xxx (55 cc), 95-2xxx (75 cc), and 96-2xxx (100 cc) pumps
Serial numbers
Change goes into effect with s/n 88-14-xxxxx on 55 cc pumps and with s/n 88-16-xxxxx for 75 cc and 100
cc pumps

Parts Manual
Service bulletin
Part numbers affected

• New 55 cc slider block is p/n 8000189
• New 55 cc servo arm/swashplate kit is p/n 8000201
Parts disposition
Non-interchangeable

Parts Manual
Service bulletin
SB-1988-016
Products affected
Series 90 pumps
Subject
Change to fix clearance slipper hold down.
Description
As a product improvement, Danfoss has simplified the design of the series 90 pump slipper hold down
mechanism. The hold down changes from spring loaded with a fixed maximum clearance design.
The leaf spring (item C60) and spring aligner (item C66) will be eliminated and will not be available as
service parts. The spacer (item C50), bearing (item C40), and washer (item C65) will change and the old
part numbers will not be available as service parts. The swashplate (item D50), pistons (item C20), slipper
retainer (item C30), and screws (item C70) will remain the same.
If any of the affected parts (item C66, C60, C65, C50, or C40) require replacement during repair of older
style pumps, discard these parts and rebuild using new style parts (items C40, C50, and C65). As before,
the screws (item C70) which are coated with locking compound MUST always be replaced after removal.
C40
C50
C65
C60
C66
C70 C20
C30
D50
C50
C40
C65
Old Style C70
Slipper Hold-Down
New Style
Slipper Hold-Down
Models affected
Serial numbers
• 55 cc pumps, 94-2xxx, changed at s/n 88-43-xxxxx
• 75 cc pumps, 95-2xxx, changed at s/n 88-22-xxxxx
• 100cc pumps, 96-2xxx, changed at s/n 88-20-xxxxx
Item Qty/pump 55cc 75cc 100cc

C40 2 8000137 8100294 8200144
C50 4 8000138 8100295 8200145

Parts Manual
Service bulletin
Item Qty/pump 55cc 75cc 100cc

C65 4 9009625-0159 9009625-0159 9009625-0159
C70 4 314419 9007276-0099 9007276-0099
(9007276-0114)
Parts disposition
Non-interchangeable as individual parts, but new style C40, C50, and C65 can be used in any vintage
pump, if all three are changed.

Parts Manual
Service bulletin
SB-1988-023
Products affected
Series 90 pumps and motors
Subject
Piston improvement
Description
Product Information Bulletin PIB-8801 (March, 1988) announced the incorporation of fabricated (welded)
piston assemblies, replacing non-fabricated (hollow) piston assemblies, in the cylinder blocks of all Series
90 pumps and motors. This change increases the overall efficiency of the Series 90 product line.
To simplify service parts inventory for all Series 90 units, only individual welded piston assemblies will be
available as spare parts. The hollow pistons will be obsoleted. Part numbers for individual welded piston
assemblies are listed in this bulletin.
Since all Series 90 pumps and motors have nine (9) pistons, welded pistons being used to replace hollow
pistons during repair MUST be install in the cylinder block symmetrically, in multiples of three (3).
Welded Piston Hollow Piston

Assembly Assembly
When replacing hollow pistons with welded pistons, it is mandatory that the welded pistons be
incorporated symmetrically in multiples of three.
Models affected
All series 90 pumps and motors: 93-xxxx, 94-xxxx, 95-xxxx, and 96-xxxx pumps
Serial numbers
Welded pistons will be incorporated into all series 90 pumps and motors by the end of the first quarter of
1998.
Part number Description

706101 Piston assembly, welded - 42 cc

Parts Manual
Service bulletin
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-1989-002
Products affected
Series 90 pumps
Subject
Incorporation of adjustable charge relief valve
Description
As a product improvement Danfoss is incorporating an adjustable charge relief valve on all series 90
variable displacement pumps. This design replaces the previous shim adjustable charge relief valve. The
new design valve provides a range of pressure adjustment which covers the available charge pressure
options of 290, 348, and 406 psi [20, 24, and 28 bar].
This improvement changes the design of the charge relief valve poppet and plug. The new style charge
relief may protrude from the pump end cap approximately 0.27 in [6.9 mm] farther than the adjustable
relief valve.
To adjust the new design valve, first install a gauge to measure charge pressure as described in the series
90 service manual. Loosen the adjustment lock nut with a 1-1/16 in hex wrench. Operate the pump at an
input speed of 1700 to 2000 rpm and turn the adjustment plug with a large screwdriver while observing
the charge pressure. Clockwise rotation of the plug increases the setting, while counterclockwise rotation
decreases the setting at a rate of approximately 50 psi [3.4 bar] per turn. Once the desired setting is
achieved, torque the lock nut to 34-41 lbf·ft [46-55 Nm], and remove the charge pressure gauge.
Danfoss will offer an adjustable charge relief valve kit for sale as a service part. This kit can be used to
service any vintage series 90 variable pump. Since the new and old style charge relief valves are
interchangeable as an assembly, the old style parts will no longer be available as service parts.
Models affected
All 93-2xxx, 94-2xxx, 95-2xxx, and 96-2xxx pumps
Part number Description

8002K000-A Adjustable charge relief valve kit - new style (includes
poppet, spring, plug, O-ring, and nut)
Parts disposition
Interchangeable (as an assembly)

Parts Manual
Service bulletin
SB-1989-003
Products affected
Series 90 pumps
Subject
Swashplate leveler spring seat change and servo pressure relief valve deletion
Description
As a product improvement, Danfoss is adding hardened shims between the swashplate leveler springs
and the end cap in series 90 variable pumps. In addition, the leveler spring seats have been hardened,
and are now separate pieces from the leveler. Previously, the seats were peened to the leveler.
These improvements require some minor changes in the repair procedures for the series 90 pumps.
When installing the lever springs (E80), take care that the spring seats (E22) are in position on the
swashplate leveler (E20). Before installing the end cap, assemble the hardened shims (E24) into their
pockets in the end cap and retain with petroleum jelly.
In an unrelated change, the servo pressure check relief valves installed in the pump end cap (or rotation
valve housing) are no longer required. These valves (P70) will be replaced by standard socket head,
straight thread O-ring plugs.
The swashplate leveler, plus the separate spring seats, are directly interchangeable with the old design
part. When performing major repairs on any series 90 pump, the hardened shims should be installed
between the leveler springs and the end cap. The plugs are also interchangeable with the servo pressure
check relief valves.
End Cap
E22
E80 E20
E22
E24 E80
E24
P80
P70
Models affected
All 93-2xxx (42 cc), 94-2xxx (55 cc), 95-2xxx (75 cc), and 96-2xxx (100 cc) pumps
Serial numbers
The hardened swashplate leveler spring seats and hardened shims incorporated at serial number 89-09-
xxxxx. Due to the interchangeability of the straight thread plugs with the servo pressure check relief
valves, this change will be incorporated during the 1st quarter of 1989.
Item Description Qty 42cc 55cc 75cc 100cc

E20 Leveler 1 673897 8000094 8100130 8200007
E22 Spring seat 2 358820 358838 358523 358846

Parts Manual
Service bulletin
Item Description Qty 42cc 55cc 75cc 100cc

E24 Shim 2 359034 359042 359042 359059
P70 Plug 2 9005110-4400 9005110-4400 9005110-4400 9005110-4400
Parts disposition
Non-interchangeable

Parts Manual
Service bulletin
SB-1989-006
Products affected
Series 90 pumps
Subject
Charge pump design change
Description
The original series 90 charge pump design included two (2) port plates, one (1) on each side of the
gerotor. If the charge pump displacement was less than the maximum available for the pump’s frame
size, the inside port plate was thicker than the 0.050 in. (1.27 mm) outside port plate.
The new design charge pump will always have two (2) 0.050 in (1.27 mm) thickness port plates, one (1) on
each side of the gerotor. Additionally, if the charge pump displacement is less than the maximum
available for the pump’s frame size, one (1) or two (2) spacers were install between the outside port plate
and the charge pump cover.
In addition, the location of the keyway in the change pump shaft has been changed to ensure full
engagement of the drive key in the gerotor. The new charge pump shaft used in 75 and 100 cc pumps
has two (2) keyways. The rear keyway (farthest from the end cap and splined end of the shaft) is used for
75 cc pumps, while the front keyway is used for 100 cc pumps. The new style charge pump shafts for 55,
75, and 100 cc pumps also changed from having a beveled end to a square end on the end closest to the
pump end cap.
Drive key Drive key

Charge pump shaft
Charge pump shaft
Inner Port Plate
Inner Port Plate
Gerotor
Outer Port Plate Gerotor
Outer Port Plate
Spacer
Charge Pump
Charge Pump
Cover Identifying groove for
2nd Spacer
(used only with 17 cc/rev 75 cc keyway
for 100 cc pump) 75 cc keyway
Note beveled Note square

100 cc keyway
end end
Old charge pump shaft New charge pump
shaft for 75 cc and
100 cc pumps
Models affected

Parts Manual
Service bulletin
Serial numbers
• A-89-17-xxxxx for all pumps manufactured in Ames, Iowa.
• N-89-07-xxxxx for all 95-2xxx (75 cc) pumps manufacture in Neumunster, West Germany.
• N-88-48-xxxxx for all 96-2xxx (100 cc) pumps manufacture in Neumunster, West Germany.

Proper part number versus pump serial number information can be found in the series 90 Parts Manuals.
The thicker inside port plates (thicker than 0.050 in (1.27 mm) will be obsoleted and no longer available
as service parts. If these parts require replacement, use the 0.050 in. 1.27 mm) port plate and appropriate
spacer(s) as service parts. On 100 cc pumps only, the new charge pump shaft must be used if the new
style spacer is used on 55 and 75 cc pumps, the change pump shaft clearance pocket in the end cap
changed from a beveled to a straight corner to correspond with the change in the charge pump shaft.
Old style charge pump shafts will remain available as service parts and must be used in the 55 and 75 cc
beveled pocket end caps.
Old style (beveled pocket) end caps will be obsoleted and no longer available as service parts. If an old
style end cap needs replacement, new style end caps can be used with any vintage charge pump
hardware and charge pump shaft.
Parts disposition
Non-interchangeable- must use correct charge pump shaft per serial number of pump

Parts Manual
Service bulletin
SB-1989-023
Products affected
Series 90 100cc variable pumps
Subject
Reduction in overall length
Description
To improve application flexibility, the overall length of series 90 100 cc pumps will be reduced by .39” [10
mm]. Some port locations will also change.
Shown below are all dimensional differences between the current and new design pumps.
E
To Split
Flange
Port "A"
C
Charge Pump
Inlet
B
Charge Pump
Inlet
Dim Old New

A 11.22” [285 mm] 10.94” [277.9 mm]
B 11.73” [297.9 mm] 11.34” [288 mm]
C 3.64” [92.5 mm] 3.53” [89.7 mm]
D* 13.73” [348.7 mm] 13.34” [338.8 mm]
E 3.87” [98.3 mm] 3.75” [95.3 mm]
* All dimensions from the mounting face to an auxiliary pump will also be reduced by .39" [10 mm].
Models affected
All 96-2xxx variable pumps
Serial numbers
This change will take place at the serial number A-89-46-xxxxx

Parts Manual
Service bulletin

Non-interchangeability will exist with drive shafts, which become shorter with this change,end caps, end
cap gaskets, and the end cap to the variable housing retaining screws. Old style end caps will no longer
be available as service parts. In the rare event that a new end cap is required, a new shaft, end cap gasket
and screws will also be needed. The new part numbers are as follows:
Item Part number Description Quantity

G04 8200175 End cap, side port 1
G30 8200166 Gasket 1
G90 9007210-0608 Screw 1
G95 9007210-0608 Screw 1
J80 9007314-1623 Screw 4
J80N 9007210-1621 Screw 4
L100 8200169 Shaft, 23 tooth spline 1
L100 8200173 Shaft, tapered 1
L100 8200176 Shaft, straight key 1
Parts disposition
Non-interchangeable

Parts Manual
Service bulletin
SB-1992-003
Products affected
Series 90: 55, 75,100.130 cc pumps
Subject
Block point change: components redesign
Description
As part of our overall series 90 product improvement program, numerous components are being
redesigned. This redesign is referred to as a “block point” change. The objective of the block point
change is to minimize the number of times we change the units while we convert to high volume tooling
at various plant sites. These design improvements will provide increased reliability and more application
flexibility. The nature of these changes makes customer re-qualification unnecessary. Old style (pre-block
point) variable housings and end caps will no longer be available as spare parts.
Models affected
All series 90 94-2xxx, 95-2xxx, 96-2xxx, and 97-2xxx variable pumps
Serial numbers
Changes will take place at the serial number 92-12-xxxxx for 100 cc pumps
Housing
Thickness adjacent to the side cover has been increased
Side cover
Thickness increased
End cap
Match housing change; small end cap screws will be larger, orientation of charge relief
valve on side port end caps has been changed from oblique to vertical.
Item Description Old part number New part number

B10 Variable housing 8200117 (O) 726554
E10 Side cover 8200011 748560
F20 Slider block 8200016 (I)(O) 8200225 (I)
G93 Spacer 8800404 8800564
G94 Lifting bracket 8800401 8800565
G95 Washer n/a 9009610-3469
B82 Plug n/a 9005110-5600
B83 Plug n/a 9005110-5600
G048 End cap - twin ports 8200157 (O) 8200235
G308 End cap gasket 8200166 8200212
G908 Screw 9007210-0608 9007314-0810
G958 Screw 9007314-0608 9007314-0810
G968 Screw 9007314-0607 9007314-0808
G046 End cap - side ports 8200175 (O) 8200236
G306 End cap gasket 8200166 8200212
G906 Screw 9007314-0608 9007314-0810

Parts Manual
Service bulletin
Item Description Old part number New part number

G956 Screw 9007314-0608 9007314-0810
G968 Screw 9007314-0607 9007314-080
G172 Plug n/a 9005110-4400
G182 Plug n/a 9005110-4400
Parts disposition
Non-interchangeable

Parts Manual
Service bulletin
SB-1992-011
Products affected
Series 90 - 055, 075, and 100 frame size pumps
Subject
Feedback link retention
Description
Effective in September of 1992, the feedback link in series 90 pumps will be mechanically retained to the
swashplate. In the past, the link slipped over a specially ground socket head screw and could fall off the
screw during assembly. The screw has changed to include a head to retain the link. The feedback link
does not change.
Special Screw
Control Feedback Link

Swashplate Assembly
Swashplate Guide
Models affected
Serial numbers
Pumps with serial number A-92-38-xxxx and beyond include the new feature.
Frame size Old screw New headed screw

55 & 75 cc 9007276-0109 9007375-0044
100 cc 9007375-0030 9007375-0032
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-1993-001
Products affected
Series90 - 55, 75, and 100 cc pumps
Subject
Charge pump design change
Description
The serial numbers mentioned apply only to Ames production units. Neumunster will incorporate the
change in July or August of this year.
To improve efficiency and reliability, the number of parts in series 90 charge pumps is being reduced. The
charge pump design on 55 cc through 100 cc frame sizes is being changed such that the outer port plate
(H30) is an integral part of the charge pump cover (J15) and distance plates are eliminated.
For auxiliary pad options, the new charge pump cover is rotation dependent. The cover will be marked
either left hand (L) or right hand (R). The non-auxiliary pad cover is not rotation dependent.
The charge pump shaft also changes and must be replaced when using the new style hardware. The
complete charge pump assembly can be interchanged with corresponding hardware from 89-17 and
beyond. However, piece parts are not interchangeable. For units prior to 89-17, consult Danfoss.
Models affected Serial numbers

All 94-2xxx, 95-2xxx, and 96-2xxx pumps
Serial numbers
• 55 cc: A-93-10 & beyond
• 75 cc: A-93-10 & beyond
• 100 cc: A93-15 & beyond
55 cc 75 cc 100 cc Item number Description

Before 93-10 After 93-10 Before 93-10 After 93-10 Before 93-15 After 93-15
8000169 8000268 N/A N/A N/A N/A H05 11 cc charge
pump set
8000170 8000269 8100313 8100479 N/A N/A H05 14 cc charge
pump set
8000171 8000270 8100314 8100480 8200158 8200238 H05 17 cc charge
pump set
N/A N/A 8100315 8100481 8200159 8200239 H05 20 cc charge
pump set
N/A N/A N/A N/A 8200160 8200240 H05 26 cc charge
pump set
8800314 N/A 8800314 N/A 8800314 N/A H30 Port plate
N/A Incl. in H05 N/A Incl. in H05 8800315 Incl. in H05 H31 Port plate
8000174 8000267 337956 8100476 337956 8100476 H50 Charge pump
shaft
8800513 8800834 8800513 8800834 8800513 8800834 J15N Charge pump
cover assy.
8800514 See J15L/R 8800514 See J15L/R 8800514 See J15L/R J15 Aux. charge
pump cover

Parts Manual
Service bulletin
55 cc 75 cc 100 cc Item number Description

Before 93-10 After 93-10 Before 93-10 After 93-10 Before 93-15 After 93-15
N/A 8800833 N/A 8800833 N/A 8800833 J15L Aux. L.H. cover
assy.
N/A 8800832 N/A 8800832 N/A 8800832 J15R Aux. R.H. cover
assy.
Piece parts are not interchangeable
Parts disposition
Interchangeable for s/n 89-17-xxxxx and beyond. Piece parts are not interchangeable.

Parts Manual
Service bulletin
CURRENT CHARGE PUMP CONFIGURATION

EXCEPT FOR 100 CC FRAME SIZE PUMPS
CURRENT CHARGE PUMP

CONFIGURATION FOR 100 CC
FRAME SIZE PUMPS
NEW CHARGE PUMP

H60 CONFIGURATION
H50
H40
H30
H05
H60
H50
H05 H40
(H30) (H31)
J80N
H30
OR H60
H50
H40
H05
OR
J40N
J15
J15N J10
H70
H80 J30 L J30
J50
J70
OR
J80
H80
J60 REF
NEW CHARGE PUMP COVER J90 H70
REF
FOR PUMPS WITHOUT AUXILIARY PADS
(SAME COVER FOR LEFT HAND OR J92
RIGHT HAND ROTATION) J
J95
L
NEW CHARGE PUMP COVERS FOR PUMPS WITH AUXILIARY PADS
(LEFT HAND AND RIGHT HAND ROTATION VERSIONS INCLUDED
IN AUXILARY PAD KIT)
THE NEW CHARGE PUMP COVERS HAVE AN 'L' OR 'R'

STAMPED ON THEM FOR EASY IDENTIFICATION

Parts Manual
Service bulletin
SB-1993-015
Products affected
Series 90 pump: all frame sizes
Subject
Servo arm interference with speed sensor ring
Description
This service bulletin revision adds the 42 cc frame size and the incorporation date of 55 through 100 cc.
A potential interference problem has been identified in series 90 42, 55, 75, and 100 cc frame size pumps
built since early 1992. Interference may occur between the swashplate hold down bracket on the servo
arm and the speed sensor ring, which may be installed on the cylinder block as an option.
A new hold down bracket has been designed to provide clearance for the speed sensor ring.
If a cylinder block with speed ring must be installed in one of the subject pumps, a servo arm assembly
with the new hold down will also be required.
Sometime during the first quarter of 1994, all 55, 75, and 100 cc pumps will be equipped with the new
design hold down bracket. The 42 cc pumps will implement the new design hold down bracket in the
second quarter of 1994.
Servo Arm Assembly
Clearance Slot for

Speed Sensor Ring
Swashplate
Models affected
All 93-2xxx, 94-2xxx, 95-2xxx, and 96-2xxx variable pumps
Serial numbers
• 42 cc at serial number 92-16-xxxxx
Frame size Old servo arm (no slot in bracket) New servo arm (with slot in
bracket)
42 cc 354282 502976
55 cc 8000191 8000318
75 cc 8100366 8100499
100 cc 8200182 8200268

Parts Manual
Service bulletin
Parts disposition
Non-interchangeable - Pumps with speed sensor ring must use the new servo arm.

Parts Manual
Service bulletin
SB-1994-017
Products affected
Series 90 55-100cc variable pumps
Subject
Swashplate cage locator
Description
As a product improvement, Danfoss has made a design change to the cage locator link used on the 55
thru 100 cc variable pumps.
The new link is made from square wire. In the past, the link was made from round wire, This is an
interchangeable change.
Cage Locator Link
Models affected
All 94-2xxx + 942xxx, 95-2xxx, + 952xxx and 96-2xxx + 962xxx variable pumps
Serial numbers
• 55and 75 cc pumps serial number 94-18-xxxxx
• 100 cc pumps will begin 4th quarter 1994
Size Old link New link

55cc 8100241 8100506
75cc 8100241 8100506
100cc 8200108 8200273
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-1994-018
Products affected
Series 90 variable pumps
Subject
Side cover washer elimination
Description
The washers located under the side cover screws have been removed on all series 90 42 through 130 cc
variable pumps.
As before, the side cover screws must be replaced if they are removed for any reason. The special coating,
which seals and retains the screws, wears off when the screws are removed.
The screw length changed on 55 through 100 cc pumps, so it is important that the washers are discarded
during repair. The proper screw is included in the overhaul seal kits.
Washer - No Longer Used

New Special Screw
Models affected
All 93-2xxx, 94-2xxx, 95-2xxx, 96-2xxx, and 97-2xxx variable pumps
Serial numbers
Change took place during the quarter 2 and 3 of 1994
Pump size Old screw New screw

42 cc 648477 Same part number
55-100 cc 9007276-0115 517228 (5000206)
130 cc 308700 Same part number

Parts Manual
Service bulletin
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-1994-035
Products affected
Subject
Elimination of housing/end cap screw
Description
As a product improvement, Danfoss reinforced the 100 cc pump housing, eliminating the need for the
screw shown below.
The hole was not removed from the end cap gasket so it can be used with any housing/ end cap
combination.
The hole was removed from the end cap, but the part number did not change. The new end cap can be
used with either housing.
The old housing was obsoleted and is no longer available as a service part.
Housing
Gasket
End cap
Screw
(deleted)
Models affected
All series 90 100cc variable pumps
Serial numbers
Change occurred at serial number 95-07-xxxxx

Parts Manual
Service bulletin
Description Part number (prior to 95-07) Part number (95-07 & beyond)
Housing 726554 8200305
Screw 9007314-0808 no longer required
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-1994-36
Products affected
Series 90 55 thru 130 cc variable pumps
Subject
Integral filtration manifold
Description
As a product improvement, Danfoss is changing the integral filter manifold and bulkhead nut to make it
more easily indexed.
The old bulkhead nut may be used with either the old or new filter manifold. The new bulkhead nut can
only be used with the new filter manifold.
The old bulkhead nut will remain available as a service part. The old filter manifold will be obsoleted and
no longer available as a service part.
Old Design
Manifold
Nut
New Design
Manifold
Nut
Models affected
All series 90 55 thru 130 cc variable pumps with “L”, “M”, or “P” filtration option code
Serial numbers
Change occurred at serial number95-18-xxxxx
Description Part number (prior to 95-18) Part number (after 95-18)

Filter manifold 8800200 8800896
Bulkhead nut 9002863-1600 5000222
Parts disposition
Interchangeable- new bulkhead nut can only be used with new filter manifold

Parts Manual
Service bulletin
SB-1995-003
Products affected
Series 90 variable pumps, all frame sizes
Subject
Manual displacement control (MDC) with DC electric solenoid override
Description
In order to accommodate our European customers, the manifold which attaches to the front of the
manual displacement control (MDC) housing is being changed.
The European solenoid valve requires a thicker manifold to provide clearance between the solenoid and
the front of the MDC housing. The revised manifold will protrude closer to the mounting flange of the
pump, reducing dimension“A” shown in the accompanying drawing by approximately 5 mm [0.2 in].
Please see chart below for specific clearances.
The thicker manifold requires longer screws and may be used with either the U.S. or European sourced
solenoid.
This change will become effective during March of 1995. The old manifold will be obsoleted and no
longer available as a service part.
Solenoid valve
Manifold
"A"
"X"
Neutral Start
Switch (NSS)
Option
Top view Series 90 Front view

Manual displacement control View in "X" direction
with DC solenoid override
Frame size 42 55 75 100 130

Dimension "A" Old 39.9 [1.57] 55.9 [2.20] 54.1 [2.31] 60.2 [2.37] 74.4 [2.93]
mm [in]
New 34.9 [1.39] 50.9 [2.0] 49.1 [1.93] 55.2 [2.17] 69.4 [2.73]
Models affected
All series 90 variable pumps using MDC with DC electric solenoid override.
Description Current part number New part number Quantity

Manifold 8800365 505022 1
Screw 9007314-0605 9007314-0606 2
Parts disposition
Interchangeable (new manifold requires longer screws)

Parts Manual
Service bulletin
SB-1995-025
Products affected
Series 90 55, 75, and 100 cc variable pumps
Subject
Side cover design change
Description
As a product improvement, Danfoss is changing the side cover and swashplate leveler (“T-bar”) guide
post design.
The new design side cover will have two hardened inserts in the machined slot, which serves as a guide
for the swashplate leveler, and modified guide posts. The swashplate leveler does not change.
Old guide posts will remain available for service requirements of pumps with the old design side cover.
The old style side cover will be obsoleted and no longer available as a service part. A service kit has been
created for replacing the old design side cover. The kit includes the new side cover, guide posts, and
inserts.
Piece parts are not interchangeable.
Guide Post
Guide Post
Swashplate Leveler
Inserts
Side Cover
Models affected
All 55,75, & 100 cc variable pumps
Serial numbers
This change became effective at serial number A-95-50-xxxxx.

Parts Manual
Service bulletin
Description Old part numbers New part numbers

Guide post Side cover Insert assy. Guide post Side cover kit
55 cc 8100353 8000157 8000406 8000379 8510097
75 cc 8100353 8100226 8100562 8000379 8510098
100 cc 8100353 746560 8200321 8000379 8510099*
Parts disposition
Interchangeable as a kit. Piece parts are not interchangeable.

Parts Manual
Service bulletin
SB-1996-009
Products affected
Series 90 55, 75, and 100 cc variable pumps
Subject
Change swashplate feedback link
Description
As a product improvement, Danfoss is changing the design of the swashplate feedback link used on the
55, 75, and 100 cc variable pumps.
The new swashplate link has a counter bore that allows for clearance between the feedback link and the
servo arm screw. The counter bore side of the link must be installed such that the counter.
Counter bore
Models affected
All 942xxx, 952xxxx, and 962xxx variable pumps
Serial numbers
For 55and 75 cc pumps, the change became effective at serial number A-96-22-xxxxx. For 100 cc pumps,
the change became effective at serial number A-96-12-xxxxx.
Frame size Old part number New part number

55cc 8000096 8000481
75cc 8000096 8000481
100cc 8200106 8200344
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-1997-048
Products affected
Series 90 100 cc variable pumps
Subject
Swashplate leveler assembly design change
Description
Danfoss has changed the design of the swashplate leveler, guide post, and spring seat assembly used on
series 90 100 cc pumps. This change improves the serviceability of the pump by eliminating the potential
for interference between the hall effect speed sensor and the swashplate leveling springs. The
swashplate leveler, guide post, and spring seat designs have been optimized to produce predictable and
uniform spring deflection during the assembly and operation of the pump. This change became effective
on new production pumps in November of 1997.
The design optimization requires that all three parts (swashplate leveler, guide post, and spring seat) be
utilized as an assembly. Danfosss recommends that all three parts be replaced when servicing any one of
the parts individually. As an additional convenience Danfoss has created service kit 8510204 comprised
of the side cover assembly, swashplate leveler, guide posts, and spring seats.
The previous spring seat has been obsoleted and is no longer available, therefore all three components
or the service kit must be utilized when the servicing of a pump, with a serial date code prior to A-97-46-
xxxxx, requires a new spring seat.
The previous leveler will remain available as a service item for a period of time, however Danfoss
recommends that when servicing of the leveler is required, on pumps with a serial date code prior to
A-97-46-xxxxx, all three components or the service kit be utilized.
The previous guide post will remain available as a service item indefinitely, due to usage within other
series 90 products. Danfoss recommends that when servicing of the guide post is required, on pumps
with a serial date code prior to A-97-46-xxxxx, all three components or the service kit be utilized.
Guide Posts
Leveler
Spring Seats
Models affected
All 96-2xxx and 962xxx variable pumps
Serial numbers
This change became effective at serial number 97-46-xxxxx

Parts Manual
Service bulletin
Description Prior to 97-46 Service kit Current production

Spring seat 358846 8510204 8200392
Swashplate leveler 8200007 8510204 8200395
Guide post 8000510 8510204 8000575
Side cover kit 8510099* 8510204 -
Parts disposition
Non-interchangeable

Parts Manual
Service bulletin
SB-1998-018
Products affected
Series90 55, 75, and 100 cc variable pumps
Subject
Swashplate bearing cage locator pin
Description
Danfoss has modified the design of the swashplate bearing cage locator pin used in the series 90 55, 75,
and 100 cc variable displacement pumps.
The improved design includes a rubber gripping element on the portion of the pin that is in the main
pump housing. The rubber element aids in retaining the pin in the housing during normal pump
assembly and servicing procedures, by increasing the interference fit between the pin and the pilot hole
in the pump housing.
To aid in identifying this change, Danfoss has released a new part number for the updated pin design.
The new pin is completely interchangeable with the previous pin part number. The previous pin has been
obsoleted.
Previous New
Models affected
All 94-2xxx, 942xxx, 95-2xxx, 952xxx, 96-2xxx and 962xxx variable pumps
Serial numbers
This change became effective at serial number 98-24-xxxxx
Pin part number

Prior to 98-24 98-24 and on
8100235 8801135

Parts Manual
Service bulletin
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-1998-041
Products affected
Series 90 55, 75, and 100 cc variable pumps, Series 90 55 and 75 cc variable motors
Subject
Piston hold down mechanism design change
Description
Danfoss has initiated a change to the piston hold down mechanism used on series 90 55, 75, and 100 cc
variable displacement pump and the series 90 55 and 75 cc variable displacement motors.
Previously, the hold down assembly consisted of a spacer, slipper guide bearing, washer, and screw. The
spacer provides a fixed amount of operational clearance for the slipper and slipper retainer. The guide
bearing provides a wear surface for the slipper retainer, while the hold down screws and washers retain
the assembly.
The change involved with the current design update is the removal of the washer from the assembly. This
design was initially introduced on the series 90 42 and 130 cc pumps in 1994, and with this change a
uniform product family is achieved.
With the removal of the washer, the required length of the assembly screw is reduced. The change in the
assembly screw also affects the dimensions of the spacer. Therefore, with this change, the part numbers
associated with the assembly screw and spacer have been changed. Some of the assembly screws are
parts already maintained in the parts system.
Although the new spacer and assembly screw are directly interchangeable with the previous swashplate
assembly components, we recommend that the components be serviced in combination. Since the new
spacer may be serviced as a stand alone item, the previous spacer has been obsoleted and will no longer
be available as a service part.
Spacer
Guide bearing Spacer
Washer Guide bearing
Screw Screw
Previous hold down design New hold down design
Models affected
94-2xxx,942xxxx, 95-2xxx, 952xxxx, 96-2xxx, and 962xxxx variable pumps
94-2xxx,942xxxx, 95-2xxx, and 952xxxx variable motors
Serial numbers
Danfoss Ames production - effective at serial number A-98-48-xxxxx

Parts Manual
Service bulletin
Component Displacement Prior to 98-48 Current

Hold down screw 55 cc 314419 (9007276-0114) 648477
Spacer 55 cc 8000266 8000619
Washer - pumps 55 cc 9009625-0159 N/A
Washer - motors 55 cc 9009625-0129 N/A
Hold down screw 75 cc 9007276-0099 9007276-0114
Spacer 75 cc 8100450 8100777
Washer - motors 75 cc 9009625-0129 N/A
Hold down screw 100 cc 9007276-0099 9007276-0114
Spacer 100 cc 8200216 8200422
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-1998-066
Products affected
Series 90, 55, 75, and 100cc variable pumps
Subject
Charge pump shaft part number change
Description
As a product improvement, Danfoss has modified the design of the charge pump shaft used in series 90
55, 75 and 100 cc pumps. This change affects all charge pump sizes (11, 14, 17, 20, 26, and 31 cc) available
in the series 90 displacement range.
The series 90 55 cc variable displacement pump uses the same charge pump shaft, regardless of charge
pump size (11, 14, or 17 cc). The series 90 75 and 100 cc variable displacement pumps, utilize a common
charge pump shaft for the standard size charge pumps (75 cc standard equals 14, 17, and 20 cc and 100
cc standard equals 17, 20, and 26 cc).
A unique charge pump shaft is utilized by series 90 75 cc variable displacement pumps equipped with
the 26 cc size charge pump., while the same unique shaft is used by series 90 100 cc variable
displacement pumps equipped with 31 cc size charge pumps.
The design modification includes a surface finish change to the charge pump shaft which improves the
wear characteristics between the charge pump shaft and the journal bearings in the charge pump cover
and end cap.
To assist in identifying this change, Danfoss has released new charge pump shaft part numbers. The new
shafts are completely interchangeable with the previous shafts. The new shaft has replaced the previous
shaft in new pump assemblies and charge pump service kits. The previous shafts have been obsoleted
and are no longer available as a service part. The chart on the next page will assist you in determining the
part number changes.
Charge Pump Shaft
Models affected
94-2xxx, 942xxxx, 95-2xxx, 952xxxx, 96-2xxx, and 962xxxx variable pumps

Parts Manual
Service bulletin
Pump models 9621723 and 9622117 were released with a special charge pump option (code W-26 cc
charge pump with special shaft). With this product modification, the charge pump option code for these
two models has been changed from W to the standard option (code F-26 cc charge pump). The special
shaft part number 8801176 has been obsoleted and replaced with shaft part number 8801178.
Serial numbers
Danfoss Ames production - effective at serial number A-99-40-xxxxx
Danfoss Neumunster production - effective at serial number N-99-39-xxxxx
Series 90 Size Charge pump Previous shaft New shaft Charge kit
No aux. pad LH w/aux. RH w/aux.
55 11 8000267 8801177 8510028 8510029 8510030
55 14 8000267 8801177 8510031 8510032 8510033
55 17 8000267 8801177 8510034 8510035 8510036
75 14 8100476 8801178 8510037 8510038 8510039
75 17 8100476 8801178 8510040 8510041 8510042
75 20 8100476 8801178 8510043 8510044 8510045
75 26* 8100478 8801179 N/A N/A N/A
100 17 8100476 8801178 8510046 8510047 8510048
100 20 8100476 8801178 8510049 8510050 8510051
100 26 8100476 8801178 8510052 8510053 8510054
100 31* 8100478 8801179 N/A N/A N/A
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-1998-070
Products affected
Subject
Swashplate leveler design change
Description
Danfoss has modified the design of the swashplate leveler and spring seat assembly used on Series 90
100 cc pumps. The assembly and serviceability of the pump has been improved by integrating the spring
seat directly into the swashplate leveler.
The new design still provides the same predictable and uniform spring deflection during the operation of
the pump, but eliminates the potential for the spring seats to separate from the leveler during assembly
and servicing. Side cover service kit 8510204 has been updated to include the new integrated leveler,
while maintaining the latest side cover assembly and guide posts.
As communicated previously in Service Bulletin 9748, Danfoss recommends that the leveler, spring seat,
and guide post parts be serviced as a group on Series 90 100cc pumps with serial dates between 92-12-
xxxxx to 97-46-xxxxx. With the integrated leveler, this is represented as follows;
Swashplate levelers 8200007 and 8200395 and spring seat 8200392 have been obsoleted and will no
longer be available as a service part. Guide post part number 8000575 will remain unchanged.
When servicing of the leveler is required on pumps with serial dates after A-97-46-xxxxx, the new
integrated swashplate leveler/spring seat (8200393) can be used. When servicing pumps with serial dates
between A-95-50-xxxxx and A-97-46-xxxxx, the new integrated swashplate leveler/spring seat (8200393)
and guide post (8000575) or the side cover service kit must be utilized. When servicing pumps with serial
date between A-92-12-xxxxx and A-95-49-xxxxx,the side cover service kit must be used. When servicing
pumps with serial dates between A-87-02-xxxxx and A-92-11-xxxxx, the side cover service kit must be
used.
Guide post Guide Post
Leveler Integrated
Leveler
Spring Seats
Previous Design New Design
Models affected
All 96-2xxx and 962xxxx variable displacement pumps
Serial numbers
Danfoss Ames production: A-99-01-xxxxx.
Danfoss Neumunster production: N-99-22-xxxxx.

Parts Manual
Service bulletin
Description 87-02 to 92-11 Replacement Parts

Spring Seat 358846 Order Kit# 8510132
Swashplate leveler 8200007 Order Kit# 8510132
Guide Post 8100353 Order Kit# 8510132
Side Cover 8200011 Order Kit# 8510132
Inserts Not Applicable Not Applicable
Side Cover Kit Not Available 8510132

Spring Seat 358846 Order Kit# 8510204
Swashplate leveler 8200007 Order Kit# 8510204
Guide Post 8100353 Order Kit# 8510204
Side Cover 746560 Order Kit# 8510204
Inserts Not Applicable Order Kit# 8510204
Side Cover Kit Not Available 8510204

Spring Seat 358846 None**
Swashplate leveler 8200007 8200393*
Guide Post 8000510 8000575*
Side Cover 501574 501574
Inserts 8200321 513889
Side Cover Kit 8510204 8510204
** Use 8200393 leveler and 8000575 guide posts
* Must be replaced together

Spring Seat 8200392 None**
Swashplate leveler 8200395 8200393
Guide Post 8000575 8000575
Side Cover 501574 501574
Inserts 8200321 513889
Description 99-01 to Current Replacement Parts

Spring Seat None None
Swashplate leveler 8200393 8200393
Guide Post 8000575 8000575
Side Cover 501574 501574
Inserts 8200321 513889
Parts disposition
Interchangeable- recommend replacement as a group

Parts Manual
Service bulletin
SB-1999-019
Products affected
Series90 55, 75, and 100 cc variable pumps
Subject
Feedback link change
Description
As a product improvement, Danfoss is changing the design of the swashplate feedback link used on the
55, 75, and 100 cc variable pumps.
In 1996, a counter bore was added to the design of our swashplate link to allow for a higher clamping
load when assembled to the servo arm. This change was described in SB-1996-009. The counter bore is
no longer required on most units due to a design change to the servo arm. Danfoss recommends the old
feedback link be used when servicing pumps with dates codes prior to 96-40-xxxxx. The old feedback link
will remain available as a service part.
Counter bore
Models affected
All series 90 55, 75, and 100cc variable pumps
Serial numbers
This change became effective at serial number A-96-40-xxxxx
Size Old part number New part number

100 cc 8200344 8200413
55 & 75 cc 8000481 11070305
Parts disposition
Non-interchangeable

Parts Manual
Service bulletin
SB-1999-041
Products affected
Series 90 variable pumps
Subject
Change to side cover insert material
Description
As a continuous product improvement, Danfoss has changed the side cover insert material to improve
wear characteristics. The new material is more wear resistant than the previous material.
In order to track this change, new part numbers have been created and the old part numbers will be
obsolete.
Side Cover Insert Kit
Side Cover
Models affected
93-2xxx, 94-2xxxx, 95-2xxx, 96-2xxxx, 97-2xxx, 98-2xxx, and 99-2xxx
Serial numbers
Frame size NMS effective date Ames effective date

42 cc N-99-36-xxxxx N/A
55 cc N-00-18-xxxxx A-00-18-xxxxx

42 cc 506916 513885
55 cc 8000406 513886
75 cc 8000562 513888
100 cc 8200321 513889
130 cc 8300004 513890
180 cc 506914 513891
250 cc 506914 513891

Parts Manual
Service bulletin
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-1999-057
Products affected
Subject
Cage pin change
Description
Danfoss has discovered the possibility of a tolerance stack up issue with the bearing locator pin. The
purpose of this pin is to keep the alignment of the bearing to the swashplate. If the pin were to come out
of its position you may experience erratic pump control and/or loss of performance.
To address this issue we have lengthened the bearing locator pin by 2 mm to increase the minimum
amount of engagement.
The new pin is interchangeable with the old pin. Danfoss recommends that the pin be replaced when
servicing series 90 - 100 cc pumps. The old pin part number will remain available since it is still being used
for the 55 cc and 75 cc pumps.
Locator Pin
Models affected
All series 90 100 cc variable pumps
Serial numbers
This change became effective at serial number A-99-47-xxxxx and N-99-50-xxxxx.
Old part number New part number

8801135 8801235
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-1999-065
Products affected
Series 90 75, 100, 130, 180, and 250cc variable displacement pumps
Subject
Hydraulic displacement control gasket and swashplate bearing locator pin retention
Description
The Series 90 75cc, 100cc, 130cc, 180cc, and 250cc variable displacement pumps utilize a common gasket
to seal the joint between the displacement control housing and main pump housing.
In November 1998, Danfoss introduced a new gasket design for Hydraulic Displacement Controls (HDC -
all options), version 2 Electrical Displacement Controls (EDC2- options EE and EN), and two amp current
control (options PA and PB) equipped pumps (see SB-1998-038). The purpose of this gasket is primarily to
seal the joint and aid in the retention of the bearing cage locator pin in the main pump housing. Danfoss
has identified that the new gasket may not adequately aid in the retention of this pin in 75cc pump sizes
due to casting and machining tolerances. Installations which are particularly sensitive to pin retention
include those oriented with the control on the side or on the bottom when the pump is installed. In these
types of installations, it is possible for the pin to come out of its position in the pump housing. This will
result in a loss of alignment between the swashplate and swashplate bearing assembly and the potential
for erratic pump control and/or system performance.
To address this situation, Danfoss has introduced a design modification to the control gasket. The
modification will insure that the cage locator pin is retained in 75cc pumps in all circumstances, while still
maintaining the desired gasket clamp load to avoid leaks.
The new gasket is completely interchangeable with the previous gasket. Danfoss recommends that the
previous control gasket be replaced immediately on 75cc pump assemblies, with controls noted above,
in which the control is on the side or on the bottom of the pump. The pump serial numbers involved are
A-98-41-xxxxx through A-99-49-xxxxx.It is not required to replace the gasket in pumps with the control in
the up position, until the initial servicing of the pump assembly.
The 100cc, 130cc, 180cc, and 250cc pumps are not dependent upon the gasket to maintain retention of
the bearing cage locator pin and are not affected by the information above.
The new gasket has replaced the previous gasket in all new pump assemblies with Hydraulic
Displacement Control (HDC), version 2 Electrical Displacement Control (EDC2-EE and EN), and two amp
current (PA and PB) controls. The new gasket has also been placed in all appropriate control kits and
overhaul seal kits. Page 3 of this bulletin will assist you in identifying the new gasket from the previous
gasket.
Models affected
95-2xxx,952xxxx, 96-2xxx, 962xxxx, 97-2xxx, 972xxxx, 98-2xxx, 982xxxx, 99-2xxx, and 992xxxx variable
displacement pumps equipped with hydraulic displacement controls and specific option electronic
displacement control. (EE, EN, PA, PB)
Serial numbers
Danfoss Ames 75cc pump production:A-99-50-xxxxx.
Danfoss Ames 100cc pump production: A-00-25-xxxxx.
Danfoss Neumunster production: N-00-01-xxxxx.

Parts Manual
Service bulletin
Previous gasket New gasket

511608 8801241
Parts disposition
Interchangeable
Control Gasket
Cage locator pin
Retains Cage Locator Pin
New Gasket:
Previous Gasket:

Parts Manual
Service bulletin
SB-2000-022
Products affected
Series 90 75, 100, and 130 cc variable displacement pumps
Subject
Displacement limiter screw and servo piston change
Description
Danfoss has identified a product issue affecting a limited number of Series 90 100cc variable
displacement pumps built at the Ames, Iowa, USA facility in the time frame of June 2000 through August
2000 (serial date range A-00-23-xxxxx up to and including A-00-34- xxxxx). This same issue also affects a
limited number of Series 90 75cc, 100cc, and 130cc variable displacement pumps built at the
Neumunster, Germany facility in the time frame of June 2000 through September 2000 (serial date range
N-00-23-xxxxx up to and including A-00-39-xxxxx).
These pumps, equipped with displacement limiters, may have a servo piston with large center drills.
These large center drills may allow the displacement limiter screw to thread into the servo piston while
turning the screw in against the servo piston while adjusting the pump’s displacement. If this occurs, the
pump will be mechanically held in stroke by the displacement limiter screw. This situation can only
happen during adjustment; it will not occur during normal operation.
Danfoss has introduced a change to the servo piston and the displacement limiter screw to prevent the
recurrence of this issue. We have made a change to the servo piston to limit the size of the center drill. We
have also changed the design of the service displacement limiter screw from a “flat” point to a “dog nose”
point. When servicing a pump that meets the above criteria, you must verify that the displacement limiter
screw of the new “dog nose” version. If it is not, you must replace the displacement limiter screw with the
new version. If the pump is not inside the date code ranges and displacements mentioned, you do not
need to verify the version of the displacement limiter screws.
To assist in tracking this change, we have issued new part numbers for the servo pistons and
displacement limiter screws. Even though this issue did not affect the 42cc or 55cc pumps, the service
displacement limiter screw part number will change also to keep one common service part. We do this as
the same displacement limiter screw is used on 42cc, 55cc, 75cc, and 100cc pumps.
Old New
“flat point” “dog nose”
displacement limiter screw displacement limiter screw
Models affected
All 95-2xxx, 952xxxx, 96-2xxx, 962xxxx, 97-2xxx, and 972xxxx variable displacement pumps with 1, 2, 4, or
P displacement limitation option.
Serial numbers
Danfoss Ames 100cc production with serial number A-00-23-xxxxx up to and including A-00-34-xxxxx.
Danfoss Neumunster, Germany production with serial number N-00-23-xxxxx up to and including
A-00-39-xxxxx.

Parts Manual
Service bulletin
Frame size Old servo piston New servo piston Old screw New screw
42 & 55cc N/A N/A 9007712-0814 516677
75 cc 509282 516683 9007712-0814 516677
100 cc 509284 516684 9007712-0814 516677
130 cc 510496 516685 572180 516678
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-2000-041
Products affected
Series 90 55, 75, 1nd 100 cc variable displacement pumps
Subject
Common leveler spring shim
Description
The date code for the series 90 55cc should have been for a date code of A-92-06-xxxxx not A-02-06-
xxxxx.
Danfoss has standardized the leveler spring shim used on all 55, 75, and 100 cc variable displacement
pumps. Two different shims were used in the past. One size was for 55 and 75 cc pumps, and the other for
the 100 cc pumps. The new shim can be used in all three frame sizes.
Danfoss has issued a new part number for the new shim. The new shim is interchangeable for 55 cc
pumps built after A-92-06-xxxxx, 75 cc pumps built after A-96- 19-xxxxx,and 100 cc pumps. For pumps
manufactured prior to these dates, you will need to reuse the old shims, as the new shim outer diameter
is larger, and this will cause the new shim to not seat correctly in the bottom of the pocket in the end cap.
The old shim part numbers are obsolete.
Models affected
All 94-2xxx, 942xxxx, 95-2xxx, 952xxxx, 96-2xxx, and 962xxxx variable pumps.
Serial numbers
Danfoss Ames, Iowa production change was effective at serial number A-00-40-xxxxx
Danfoss Neumunster, Germany production change was effective at serial number N-01-27-xxxxx

55 cc 359042 8801225*
75 cc 359042 8801225**
100 cc 359059 8801225
* can only be used in pumps manufactured after A-92-06-xxxxx
** can only be used in pumps manufactured after A-96-19-xxxxx
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-2001-013
Products affected
Subject
31c charge pump improvements
Description
To improve efficiency, the 31cc charge pump assembly has been redesigned.
This change is interchangeable for pumps manufactured after the date code of A-00-10-xxxx if all
affected components are replaced. For pumps manufactured before this date, with the CE auxiliary pad
option, the auxiliary pad must also be replaced with part number 8200472. The old charge pump
components will remain available as service parts.
Charge pump
Charge pump shaft
Charge pump cover
Screw
"C" auxiliary pad
Models affected
96-2xxx,and 962xxxx variable displacement pumps with the ‘G’ charge pump displacement option.
Change was effective at serial number A-01-20-xxxxx.
Serial numbers
This change was effective at serial number A-01-20-xxxxx

Parts Manual
Service bulletin
Part description Previous part number New part number

Charge pump shaft 8801179 8801210
Charge pump set 8200245 8200479
Charge pump cover 8800868 8801248
Screw 9007210-0604 9007314-0605
Parts disposition
Interchangeable- see text in Description.

Parts Manual
Service bulletin
SB-2002-050
Products affected
Series 90 55, 75, and 100 cc pumps
Subject
Auxiliary mounting pad
Description
As a product improvement, Danfoss has changed the design of the SAE C auxiliary mounting pad to
increase strength and reduce corrosion. The old auxiliary mounting pad and new auxiliary mounting pad
are interchangeable. The new auxiliary mounting pads are frame size dependent, because they do not
have slotted mounting holes. The auxiliary mounting pad screws remain the same, but they do not
require washers.
The old auxiliary mounting pad is obsolete and no longer available as a service part. The washers will
remain available.
Old design New design
Models affected
Series 90 55, 75, and 100 cc pumps with SAE C auxiliary mounting.

The new auxiliary mounting pads are frame size dependent and do not use washers.
Frame size Old aux-pad part number New aux-pad part Old washer part number
number
55cc 723205 8000643 5000602
75cc 723205 8100848 9009625-0132
100cc 723205 8200469 9009625-0132
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-2005-011
Products affected
Series 90 42 through 100 cc pumps
Subject
Auxiliary flange charge pump cover
Description
Danfoss will no longer mark auxiliary flange charge pump cover with an “R” for right hand rotation or an
“L” for left hand rotation.
The pilot surface has changed on the covers. The right hand rotation charge pump cover will have 1 step
and the left hand rotation charge pump cover will have 2 steps. Refer to the drawings below for example.
The part numbers of the charge pump covers will not change.
Right hand Left hand

rotation rotation
Models affected
Series 90 42 thru 100 cc pumps with auxiliary pad options.
Serial numbers

None
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-2007-018
Products affected
Series 90 100 cc pumps
Subject
Pump redesign
Description
As a global improvement, the series 90 100cc pump has the redesigned the following components: servo
arm, swashplate guide, pump housing, shaft seal assembly, cradle bearing, and servo arm screw.
All parts are non-interchangeable with the exception of the shaft seal assembly. Model numbers and
order codes will not be changed.
Servo arm A“one piece” servo arm is introduced. The pin that engages the servo piston is now
machined as part of the servo arm instead of pressed in. The old servo arm will remain
available as a service part.
Swashplate The swashplate position is now guided by the fit between the servo arm and the
guide pump housing. A“shelf” on the servo arm fits under a boss in the housing to provide a
fixed clearance swashplate hold-down. The swashplate was previously held down with
a spring and bracket, which was riveted to the servo arm. The servo arm to housing
clearance now limits lateral movement of the swashplate. The swashplate guide that
was bolted to the bottom of the swashplate has been removed. The separate
swashplate guide will remain available as a service part.
Housing The housing is modified internally to provide the servo arm pivot. Also, the cradle and
side cover radii are reduced. Some customers may notice cosmetic external changes.
The old housing is obsolete and no longer available as a service part.
Shaft seal The shaft seal assembly is interchangeable, but the piece parts are not. The new lip
assembly seal has a smaller O.D. and the I.D. of the seal carrier changed accordingly. The old
shaft lip seal will remain available as a service part.
Overhaul seal A new overhaul seal kit has been created that will service both old and new design
kit pumps. The new seal kit also has additional O-rings and seal nuts required for a more
complete repair. The old seal kit is obsolete and no longer available for service.
Cradle bearing The new design is cold formed with the positioning pin now integral with the bearing.
The old cradle bearing will remain available as a service part for a period of time.
Screws The screw that holds the servo arm to the swashplate has changed from a M10 to a M8
screw. The other screw is a feedback link screw which changed from 50mm long to
45mm long. See drawing for details.

Parts Manual
Service bulletin
Servo arm screw Feedback screw Servo arm screw Feedback screw
M10 M8
Servo arm Servo arm
Swashplate guide
Spring
Locator link pin Locator link pin
Swashplate Swashplate
Old Design New Design
Models affected
Series 90 100cc pumps
Serial numbers
Description Old part number New part number

Servo arm 518629, 8200268 521607
Servo arm screw 536649, 9007276-0111 519150
Seal carrier assembly 510017, 8200309 521722
Cradle bearing 305839/P, 8200053 11131109
Swashplate guide 8800669 No replacement needed
Compression spring 673145, 8200058 No replacement needed
Shaft seal 9008000-0114 519021
Feedback screw 9007375-0032 9007375-0044
Standard housing 503424 521605
PPU housing 726554, 8200332 11002463
Side cover 501574 11000790
Seal carrier assembly 510017, 8200309 521722
Swashplate assembly 8200192 8200618
Swashplate 8200232 11002493
Overhaul seal kit 82020S30 11035669
Parts disposition
Non-interchangeable

Parts Manual
Service bulletin
SB-2007-027
Products affected
Series 90; 55, 75 , and 100 cc pumps
Subject
SAE A auxiliary mounting flange
Description
Danfoss is pleased to announce a design improvement on the SAE A auxiliary mounting flange adapter
on all its series 90 pumps. All manufacturing locations producing these pumps will be changed to this
configuration.
The improvement comes in the form of a more robust sealing geometry with a larger cross- section O-
ring. The O-ring groove in the flange will now be sized to mate with a 2.62mm [0.103] cross section O-ring
rather than the old 1.78mm [0.070] cross-section O-ring.
The Danfoss part number for the new O-ring is 9004104-1520 (2.62mm [0.103]. x 82.22mm [3.237]). The
larger cross-section sealing geometry allows for the use of a donut style A pad seal and a new flat cover
for improved assembly. This new configuration is qualified as a running cover. When installing an
auxiliary pump, the donut style A pad seal must be discarded and the part number 9004104-1520 O-ring
used.
Also, the flanges will no longer have a slotted interface with a washer for the end cap screws. The flanges
will now have round through holes for the end cap screws and will use no washers. The end cap screws
do not change. This eliminates the area where water or high pressure wash chemicals can be trapped
around the end cap screws. There now are specific part numbers for the flanges used on each of the three
displacement size pumps; 55, 75 and 100 cc.
The pumps will now be supplied with the donut style A pad seal and new flat cover, instead of the small
O-ring and cover plate (shown in the drawing below).
The overhaul seal kit will include the old O-ring, the new O-ring and the A pad seal.
Old Design New Design
Flange adapter Flange adapter

Washer
O-ring A pad seal
Cover plate Cover plate
Models affected
All series 90; 55, 75, and 100 cc pumps with SAE“A” auxiliary mounting flanges.
Serial numbers

Parts Manual
Service bulletin
Description Old p/n Used on New p/n Used on

Flange adapter 8000262 55 cc 8000641 55 cc
Flange adapter 8800172 55, 75 & 100 cc 8000641 55 cc
Washer 9009625-0132 55, 75 & 100 cc NA NA
O-ring 9004104-0420 All sizes 9004104-1520 All sizes
A Pad seal NA All sizes 4800482 All sizes
Flange cover 9802336 All sizes 4460586 All sizes
If the new auxiliary flange adapter is used, the new o-ring or A-pad seal and cover must also be used.
Parts disposition
• Interchangeable- if new o-ring or A-pad seal and cover are replaced
• Use parts in stock
• Order replacement parts
• Revise existing part orders

Parts Manual
Service bulletin
SB-2007-051
Products affected
Subject
SAE C auxiliary mounting flange
Description
Danfoss is pleased to announce a design improvement on the SAE C auxiliary mounting flange adapter
on its series 90 pumps. The frame sizes affected by this change are 55, 75, and 100cc. All manufacturing
locations producing these pumps will be changed to this configuration.
The improvement comes in the form of a more robust sealing geometry with a larger cross-section O-
rather than the old 1.78mm [0.070] cross-section O-ring. The Danfoss part number for the new O-ring is
9004104-1580 (2.62mm [0.103] x 120.32mm [4.737]). The larger cross-section sealing geometry allows for
the use of a donut style C pad seal and a new flat cover for improved assembly. This new configuration is
qualified as a running cover. When installing an auxiliary pump, the donut style C pad seal must be
discarded and part number 9004104-1580 O-ring used.
The pumps will now be supplied with the donut style seal and new flat cover, instead of the small O-ring
and cover plate (shown in the drawing below).
The overhaul seal kit will include the old O-ring, the new O-ring and the new C pad seal.
1.30 mm 1.96 mm
[0.05] [0.08]
Adapter flange
Adapter flange
C pad seal
O-ring
Flat flange cover

Piloted flange cover
Models affected
All series 90; 55, 75, and 100 cc pumps with SAE“C” auxiliary mounting flanges.
Serial numbers
This change became effective at serial number A-08-19-xxxxx and N-09-30-xxxxx

Parts Manual
Service bulletin
Description Old part number Used on New part number

SAE C flange 8200469 100cc 8200515
SAE C flange 8100848 75cc 8100897
SAE C flange 8000643 55cc 8000740
O-ring 9004100-0480 55, 75, 100cc 9004104-1580
C pad seal N/A 55, 75, 100cc 8801062
Flange cover 8800406 55, 75, 100cc 8801060
If the auxiliary flange adapter is used, the new o-ring or C pad seal and cover must also be used.
Parts disposition
• Interchangeable- if new o-ring or C pad seal and cover are replaced

Parts Manual
Service bulletin
SB-2007-055
Products affected
Subject
SAE B auxiliary mounting flange
Description
Danfoss is pleased to announce a design improvement on the SAE B auxiliary mounting flange adapter
on its series 90 pumps. The frame sizes affected by this change are 55, 75, and 100cc. All manufacturing
locations producing these pumps will be changed to this configuration.
The improvement comes in the form of a more robust sealing geometry with a larger cross-section O-
rather than the old 1.78mm [0.070] cross-section O-ring. The Danfoss part number for the new O-ring is
9004104-1540 (2.62mm [0.103] x 94.92mm [3.737]). The larger cross-section sealing geometry allows for
the use of a donut style B pad seal and a new flat cover for improved assembly. This new configuration is
qualified as a running cover. When installing an auxiliary pump, the donut style B pad seal must be
discarded and part number 9004104-1540 O-ring used.
Also, the flanges will no longer have a slotted interface with a washer for the end cap screws. The flanges
will now have round through holes for the end cap screws and will use no washers. The end cap screws
do not change. This eliminates the area where water or high pressure wash chemicals can be trapped
around the end cap screws. There now are specific part numbers for the flanges used on each of the three
displacement size pumps; 55, 75 and 100 cc.
The pumps will now be supplied with the donut style seal and new flat cover, instead of the small O-ring
and cover plate (shown in the drawing below).
The overhaul seal kit will include the old O-ring, the new O-ring and the new B pad seal.
1.30 mm 1.96 mm
[0.05] [0.08]
Adapter flange Adapter flange
Washer
O-ring
- B pad seal
Flat flange cover

Piloted flange cover
Models affected
All series 90; 55, 75, and 100 cc pumps with SAE“B” auxiliary mounting flanges.

Parts Manual
Service bulletin
Serial numbers
Description Old part number Used on New part number Used on

Metric B flange 8800983 55, 75 & 100 cc 8200540 100 cc
SAE B flange 8800173 55, 75 & 100 cc 8200468 100 cc
SAE B flange 8800173 55, 75 & 100 cc 8100847 75 cc
Metric B flange 8800983 55, 75 & 100 cc 8100938 75 cc
SAE B flange 8800173 55, 75 & 100 cc 8000642 55 cc
SAE B flange 8000263 55, 75 & 100 cc 8000642 55 cc
Washer 9009625-0132 55, 75 & 100 cc N/A N/A
O-ring 9004104-0450 55, 75 & 100 cc 9004104-1540 55, 75 & 100 cc
B Pad seal N/A 55, 75 & 100 cc 8801061 55, 75 & 100 cc
Flange cover 4460370 55, 75 & 100 cc 8801059 55, 75 & 100 cc
If the new auxiliary flange adapter is used, the new o-ring or B pad seal and cover must also be used.
Parts disposition
• Interchangeable- if new o-ring or C pad seal and cover are replaced

Parts Manual
Service bulletin
SB-2009-035
Products affected
Series 90 75 and 100 cc pumps
Subject
Change supplier of servo piston assemblies
Description
The supplier has changed for servo piston assemblies used in Series 90 pumps, size 75 and 100 cc. These
assemblies include the servo piston, O-rings and seal rings. The part number of the servo piston
assemblies has changed to better track this change. The new servo piston assemblies are completely
interchangeable with the old servo piston assemblies. The old part numbers will become obsolete and
not available for service.
Servo piston assembly
O-ring
Seal ring
Models affected
Series 90 75 and 100cc pumps.
Serial numbers
This change went into effect at serial number A-09-25-xxxxx

Servo piston assembly, 75cc 516683 11041752
Servo piston assembly, 100cc 516684 11044943
Parts disposition
• Interchangeable

Parts Manual
Service bulletin
SB-2009-038
Products affected
Series 90 55, 75 and 100 cc pumps
Subject
The supplier for the spacers, used for slipper hold down spacing in series 90 pumps, has changed. The
new part is physically and functionally interchangeable in all applications. The part numbers have
changed to better track this change. The old part numbers will become obsolete and not available for
service.
Spacer
Models affected
Series 90 55, 75 and 100 cc pumps
Serial numbers
This change became effective at the following serial numbers:
• A09-38-XXXXX for 55cc (14-Sep-2009)
• A10-04-XXXXX for 75cc (22-Jan-2010)
• A09-38-XXXXX for 100cc (12-Aug-2009)
Spacer Old part number New part number

55cc 8000619 11065864
75cc 8100777 11065865
100cc 8200422 11065866
Parts disposition
Non-interchangeable

Parts Manual
Service bulletin
SB-2009-049
Products affected
Series 90 100cc pumps
Subject
Slider block supplier change
Description
The supplier for the slider block used in series 90 100 cc pumps has changed. The new slider block is
physically and functionally interchangeable in all applications. The part number of the slider block has
changed to better track this change. The old part number will become obsolete and not available for
service.
Slider block
Models affected
All series 90 100cc variable displacement pumps
Serial numbers
This change became effective at serial number A09-35-XXXXX. (28 August 2009)

Slider block 8200225 11061908
Parts disposition
• Interchangeable

Parts Manual
Service bulletin
SB-2009-073
Products affected
Series 90: 75 and 100 cc pumps
Subject
Supplier change for guide posts
Description
The supplier has changed, for the guide posts used in series 90: 75 and 100 cc pumps. The new guide
posts are interchangeable with the old guide posts. A new part number has been assigned to the new
guide post to better track this change. The old part number has become obsolete and not available for
service.
Guide post
Models affected
Series 90: 75 and 100cc pumps
Serial numbers
This change became effective at serial number A-09-50-xxxxx (21 December 2009)

Guide post 8000575 11056531

Parts Manual
Service bulletin

Interchangeable

Parts Manual
Service bulletin
SB-2013-011
Products affected
Series 90: 42-250cc pumps
Subject
Feedback link - control
Description
Danfoss has changed to a global supplier for the control feedback links used in Series 90 42-250cc
pumps.
Old parts and new parts are completely interchangeable. Part numbers will be changing for tracking
purposes. Old parts will become obsolete and no longer available as a service part.
Control feedback link
Models affected
Control feedback link Old part number New part number

42cc pumps 648600 11070304
55 & 75cc pumps 8000602 11070305
100cc pumps 8200413 11070306
130cc pumps 340091 11070307
180 & 250cc pumps 747451 11070308
Parts disposition
• Interchangeable

Parts Manual
Service bulletin
SB-2015-005
Products affected
Subject
Slider block supplier change
Description
The supplier has changed for Series 90 pump slider blocks. Parts are completely interchangeable.
Part numbers have been changed for tracking purposes. As a result old part numbers will become
obsolete and no longer available as service parts.
Slider block
Models affected
Series 90 42-250cc pumps
Description Old Part Number New Part Number Effective Date

Slider block 42 NMS 648303 11116314 N/A
Slider block 55-75 NMS 8800750 11116313 6-Aug-2014
Slider block 55-75 AMS 11061964 11116313 6-Sept-2014
Slider block100 AMS 11061908 11116312 10-Mar-2014
Slider block 100 NMS 756197 11116312 20-Feb-2015
Slider block 130 NMS 11000317 11116309 9-Dec-2014
Slider block 180-250 NMS 746479 11116308 24-Oct-2014
Parts disposition
• Interchangeable

Products we offer: Danfoss Power Solutions is a global manufacturer and supplier of high-quality hydraulic and
electric components. We specialize in providing state-of-the-art technology and solutions
• Cartridge valves
that excel in the harsh operating conditions of the mobile off-highway market as well as the
• DCV directional control marine sector. Building on our extensive applications expertise, we work closely with you to
valves ensure exceptional performance for a broad range of applications. We help you and other
• Electric converters customers around the world speed up system development, reduce costs and bring vehicles
• Electric machines and vessels to market faster.
• Electric motors Danfoss Power Solutions – your strongest partner in mobile hydraulics and mobile
• Gear motors electrification.
• Gear pumps Go to www.danfoss.com for further product information.

• Hydraulic integrated We offer you expert worldwide support for ensuring the best possible solutions for
circuits (HICs) outstanding performance. And with an extensive network of Global Service Partners, we also
• Hydrostatic motors provide you with comprehensive global service for all of our components.
• Hydrostatic pumps
• Orbital motors
• PLUS+1® controllers
• PLUS+1® displays
• PLUS+1® joysticks and
pedals
• PLUS+1® operator
interfaces
• PLUS+1® sensors
• PLUS+1® software
• PLUS+1® software services,
support and training
• Position controls and
sensors
• PVG proportional valves
• Steering components and
systems
• Telematics Local address:
Hydro-Gear
www.hydro-gear.com
Daikin-Sauer-Danfoss
www.daikin-sauer-danfoss.com
Danfoss
Power Solutions Trading
Danfoss Danfoss Danfoss (Shanghai) Co., Ltd.
Power Solutions (US) Company Power Solutions GmbH & Co. OHG Power Solutions ApS Building #22, No. 1000 Jin Hai Rd
2800 East 13th Street Krokamp 35 Nordborgvej 81 Jin Qiao, Pudong New District
Ames, IA 50010, USA D-24539 Neumünster, Germany DK-6430 Nordborg, Denmark Shanghai, China 201206
Phone: +1 515 239 6000 Phone: +49 4321 871 0 Phone: +45 7488 2222 Phone: +86 21 2080 6201
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products
already on order provided that such alterations can be made without subsequent changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
© Danfoss | June 2022 AX152886482434en-000401

Danfoss 90

Uploaded by

Copyright:

Available Formats

Danfoss 90

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Danfoss 90

Uploaded by

Copyright:

Available Formats

Parts Manual

Revision history Table of revisions

Date Changed Rev

June 2022 Corrected various part numbers 0401

January 2020 Corrected filter description for filtration option 9 0209

July 2019 Corrected control part numbers 0208

November 2018 Obsoleted screw part numbers in charging system 0207

February 2018 Removed part number from seal kit 0205

January 2018 Fixed typo 0204

December 2017 Updated to Engineering Tomorrow 0203

2 | © Danfoss | June 2022 AX152886482434en-000401

© Danfoss | June 2022 AX152886482434en-000401 | 3

Charge pressure setting

4 | © Danfoss | June 2022 AX152886482434en-000401

© Danfoss | June 2022 AX152886482434en-000401 | 5

Service parts identification

Model No./Ident No. 9621161

6 | © Danfoss | June 2022 AX152886482434en-000401

Example: The service part desired is item G30

About service bulletins

Procedure to identify a part

Regional part numbers

Example of a part identification (S90 100cc)

© Danfoss | June 2022 AX152886482434en-000401 | 7

Adobe Acrobat 2-page viewing

8 | © Danfoss | June 2022 AX152886482434en-000401

Auxiliary mounting pad

Special hardware features

High pressure setting port A

High pressure setting port B

Charge pressure setting

© Danfoss | June 2022 AX152886482434en-000401 | 9

Common parts and special hardware

S90 100cc pump common parts

Swashplate Leveler design

* Included in base pump seal kit Q210

10 | © Danfoss | June 2022 AX152886482434en-000401

Common parts and special hardware

Part numbers are continued on the next 2 pages.

© Danfoss | June 2022 AX152886482434en-000401 | 11

Common parts and special hardware

Swashplate Leveler design

* Included in base pump seal kit Q210

12 | © Danfoss | June 2022 AX152886482434en-000401

Common parts and special hardware

© Danfoss | June 2022 AX152886482434en-000401 | 13

Common parts and special hardware

S90 100cc pump special hardware EAB, EAS, EED

Generic speed sensor used to show part location only.

* Included in base pump seal kit Q210

14 | © Danfoss | June 2022 AX152886482434en-000401

Common parts and special hardware

Order code: EAB

Order code: EAS

Order code: EED

© Danfoss | June 2022 AX152886482434en-000401 | 15

Common parts and special hardware

S90 100cc pump special hardware EBC, EFC, EEB, EEG

(EEB & EEG)