Scribd
Upload
11 views

Tutorial 8

Uploaded by

Shriram A ep23b019
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
11 views

Tutorial 8

Uploaded by

Shriram A ep23b019
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

EE2015: Electric Circuits and Networks

Tutorial 8
(4th and 11th October 2024)

1. For the circuit shown on the right find vC (t) for t ≥ 0. The initial conditions are: (i)
vC (0− ) = 1 V, and (ii) iL (0− ) = 2 A.
iL (t) 0.5 H 1.5 Ω

+ +
cos 2t u(t) V 1F vC
−
−

2. The circuit (same as Q6 in Tutorial-6) shown below is excited by vi (t), where vi (t) =
X∞
x(t − kT0 ). The waveform x(t) is defined as follows:
k=0
(
10 V 0 < t < T0 /2
x(t) =
−5 V T0 /2 < t < T0

where T0 = 2s.
a) Sketch vo (t) after steady-state has been reached in both circuits and mark the impor-
tant points. b) Sketch vo (t), if T0 is increased or decreased by a factor of 10, keeping the
component values the same.

0.2Ω
1F
1F

vi 4F 0.2Ω vo

vi 4F vo

EE2015 Tutorial 8 Page 1 of 3 DN/VV


3. a) For the given RLC circuit, determine Is and is (t) if both sources are operating at ω =
2 rad/s, and IC = 2 ∡28◦ A. b) Now let ω = 1 rad/s, IC = 2 ∡28◦ A and IL = 3 ∡53◦ A.
Calculate (i) Is , (ii) Vs , and (iii) iR1 (t). c) Find the Thevenin impedance as seen from the
terminals of the current source. What should you assume before proceeding to calculate
ZT h ?
Is
IR1 1Ω

+
Vs 2H 2Ω 1F
−

IL IR2 IC

4. In the circuit given on the right, R1 = 1 kΩ and C = 2.533 pF. Determine the inductance
value that will make the circuit’s resonance frequency as 1 MHz.

R1

Y C R2

5. In the circuit shown on the left, R = 1 kΩ and C = 1 nF. Plot the magnitude and phase
Vo
of versus frequency. For the magnitude response use a log-log plot, whereas, for the
Vi
phase plot use a linear scale for y-axis and the log scale for the x-axis.

+ +
R
C
Vi Vo
C

− R −

EE2015 Tutorial 8 Page 2 of 3 DN/VV


6. Consider the circuit shown on the right. a) Find the resonant frequency (ω0 ) and the
half-power frequencies (ω1 , ω2 ). b) Calculate the Q-factor and bandwidth. c) Determine
the amplitude of the current at ω0 , ω1 , and ω2 .
2Ω 1 mH

+
20 sin ωt V 0.4 µF
−

7. a) Derive the transfer function of the network whose magnitude Bode plot is shown
below. Assume that the poles and zeros are either on the imaginary axis or in the
left-half plane. b) Draw the phase Bode plot of the network

EE2015 Tutorial 8 Page 3 of 3 DN/VV

You might also like