C 00EST110121905 Pages: 2

Reg No.:_______________ Name:__________________________

APJ ABDUL KALAM TECHNOLOGICAL UNIVERSITY
Second Semester B.Tech Degree Examination July 2021 (2019 scheme)

Course Code: EST110

Course Name: ENGINEERING GRAPHICS
(2019 Scheme)
Max. Marks: 100 Duration: 3 Hours

Instructions: Retain Construction lines. Show necessary dimensions. Answer any ONE
question from each module. Each question carries 20 marks

Module-I
1 The front view of line AB is 50o inclined to XY line and is 55 mm long while its top
view is 60⁰ inclined to XY line. If end A is 10 mm above HP and 20 mm in front of
VP, draw its projections. Find the true length and inclinations of line with HP and VP.
2 The end point A of a line is 20 mm above HP and 10mm in front of VP. The other end
of the line is 50 mm above HP and 15 mm behind VP. The distance between the end
projectors is 70 mm. Draw the projections of the line. Find the true length and true
inclinations of the line with the principal planes. Also locate the traces of the line.
Module-II
3 A square pyramid of base 25 mm. side and axis 60 mm long, has a corner of the base
on the ground such that the square base is inclined at 30° to the ground and the two
base edges containing that corner are equally inclined to HP. Draw the projections of
the pyramid if its axis is inclined at 60° to the VP.
4 A cylinder 40 mm diameter and 50 mm axis is resting on a point of its base circle on
VP while its axis makes 45o with VP and front view of the axis makes 35o with XY
line. Draw its projections
Module-III
5 A hexagonal pyramid side of the base 30 mm and axis 70 mm rests with its base on the
HP and an edge of the base inclined at 300 to VP. A section plane inclined at 450 to VP
and perpendicular to HP passes through the pyramid at a distance of 10 mm from the
axis and in front of it. Draw its top view, sectional front view and true shape of
section.
6 A pentagonal prism side of base 25 mm and altitude 50 mm, rests on its base on the

Page 1 of 2
 00EST110121905

HP such that an edge of the base is parallel to VP and nearer to the observer. It is cut
by a plane inclined at 45° to HP, perpendicular to VP and passing through the centre of
the axis. Draw the development of the surface of the truncated prism.
Module-IV
7 Draw the isometric view of a pentagonal pyramid, side of base 20 mm and height 50
mm which rests centrally with base on a cylinder of diameter 60 mm and height 40
mm.
8 A hollow cylinder of inside diameter 40 mm, outside diameter 60 mm and 80 mm long
is resting on its generator on the top of a rectangular slab of 80 mm x 60 mm and
height 30 mm. Draw the isometric view of the combination if the axis of the cylinder
is parallel to the longer edges of the slab.
Module-V
9 A pentagonal prism of base sides 30 mm and length 70 mm is resting on one of its
rectangular faces on the ground, behind the Picture Plane (PP) and one pentagonal face
touching the PP. The station point is 65 mm in front of the PP, 30 mm above the
ground, and 80 mm to the right of the axis of the prism. Draw its perspective view.
10 Draw the top view, front view and any one side view of the figure shown below. The
front view direction is marked with a long arrow. Any missing dimension may be
suitably assumed.

(20x5=100 Marks)
*****

Page 2 of 2
 00EST110121905

Scheme/ Answer Key for Valuation

Scheme of evaluation (marks in brackets) and answers of problems/key
APJ ABDUL KALAM TECHNOLOGICAL UNIVERSITY
SECOND SEMESTER B.TECH DEGREE EXAMINATION (2019 SCHEME), JULY 2021
Course Code: EST110
Course Name: ENGINEERING GRAPHICS
(2019-Scheme)
Max. Marks: 100 Duration: 3 Hours

Instructions
1. Answer key is attached. It is only for reference and not in scale. Students may use different
approaches for getting the correct answer. So carefully analyze the answer and allot marks
2. For allotting full marks to isometric views, orthographic drawing is not necessary if answer is
correct. If isometric projection is drawn, it can be valued out of 15 marks.
3. If a student completes an answer with a wrong simple position, then it can be valued out of
maximum 10 marks.

Module-I
1 Locating the points and drawing the projections of the line – 4 marks
Finding true length by any one method – 6 marks
Finding true inclination with VP – 4marks
Finding true inclination with HP – 4 marks
Dimensioning and neatness – 2 marks
2 Fixing points -3 marks, Drawing FV and TV- 3 marks, Drawing true length
lines -8 marks ,fixing traces –3 marks, measuring inclinations- 2 marks,
dimension and neatness- 1 marks
Module-II
3 Simple position - 8 marks, first rotation – 8 marks, Dimensions and
neatness- 4 marks
(N B: It is difficult to fix the apparent angle using the given dimensions. So
it is recommended to give the full mark if the simple position and first
rotation figures are correct.)
4 Simple position - 5 marks, first rotation – 6 marks, second rotation- 7
marks, Dimensions and neatness- 2 marks
Module-III
5 Simple position front view and top view-5, section plane-3, sectional front
view-5, true shape-5, neatness and dimension-2
6 Drawing initial position plan and elevation– 4 marks

Page 1 of 2
 00EST110121905

Locating section plane as per given condition-3 marks

Development of the prism-5 marks
Development of the bottom portion- 6 marks
Dimensioning and neatness-2mark
Module-IV
7 Orthographic view-4, Isometric view of cylinder-7, Isometric view of
pentagonal pyramid-7, Dimensioning and neatness-2mark.
8 Orthographic view – 4 marks
Isometric View of slab – 5 marks
Isometric View of hollow cylinder – 9 marks
Dimensioning and neatness-2mark
Module-V
9 Front View-3Marks

Top View- 3 Marks

Location of Station Points- 2 Marks

Perspective View-10 Marks

Dimensioning and Neatness- 2 Marks

10 Front View: 5 Marks

Top View: 5 Marks

Profile View: 5 Marks

Following first angle projection or third angle projection-3 marks

Dimensioning and Neatness: 2

****

Page 2 of 2