Scribd
Upload
479 views6 pages

HVAC Pinout

2013 Civic Si HVAC connector pinout

Uploaded by

alfalubgt
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
479 views6 pages

HVAC Pinout

2013 Civic Si HVAC connector pinout

Uploaded by

alfalubgt
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

YOUR CURRENT VEHICLE

2013 Honda Civic

HVAC Control Unit Connector for Inputs and Outputs

NOTE

Applicable vehicles:

2013 Honda CIVIC; '13

HVAC Control Unit Connector for Inputs and Outputs

HVAC Control Unit Connector for Inputs and Outputs

Wire
Cavity Terminal Name Description Signal
Color

Power source for With combination light switch ON:


1 GRY ILLUMI+
illumination battery voltage
Not
2 Not used ――― ―――
used

With combination light switch ON:


Detects illumination
3 BLU ILL-(LED) changed voltage (depending on
control signal
dashlights brightness controller)

Not
4 Not used ――― ―――
used

With ignition switch ON (II) and air mix


Outputs to drive air mix
5 PNK M-HOT control motor moving to HOT: battery
control motor to HOT side
voltage

Outputs to drive air mix With ignition switch ON (II) and air mix
6 LT BLU M-COOL control motor to COOL control motor moving to COOL: battery
side voltage

With ignition switch ON (II) and mode


Outputs to drive air mix
7 GRN MODE_MTR_DEF control motor moving to DEF: battery
control motor to DEF side
voltage

Outputs to drive mode With ignition switch ON (II) and mode


8 WHT MODE_MTR_VENT control motor to VENT control motor moving to VENT: battery
side voltage

Outputs to drive With ignition switch ON (II) and


9 PUR F/R_MTR(FRESH) recirculation control motor recirculation control motor moving to
to FRESH side FRESH: battery voltage
Outputs to drive With ignition switch ON (II) and
10 ORN F/R_MTR(REC) recirculation control motor recirculation control motor moving to
to RECIRCULATE side RECIRCU: battery voltage

Not
11 Not used ――― ―――
used

Detects potentiometer With ignition switch ON (II): about 0.5－


12 GRN RFD-P signal of recirculation 4.5 V (depending on recirculation
control motor control motor position)

Detects potentiometer With ignition switch ON (II): about 0.5－


13 GRY AMD-P signal of air mix control 4.0 V (depending on air mix control
motor motor position)

Detects potentiometer With ignition switch ON (II): about 0.5－


14 PUR MDD-P signal of mode control 4.5 V (depending on mode control
motor motor position)

Not
15 Not used ――― ―――
used

With ignition switch ON (II): about 5.0


16 BLK S_5V Outputs sensor 5 V
V

LT With ignition switch ON (II): battery


17 IG2_A/C IG2 power source
GRN voltage

Not
18 Not used ――― ―――
used
Ground for HVAC control With ignition switch ON (II): less than
19 BLK GND
unit (G504) 0.2 V

With ignition switch ON (II): less than


20 RED SENSOR_COM Sensor ground
0.2 V

Not
21 Not used ――― ―――
used

With ignition switch ON (II) and fan


control dial OFF: less than 0.2 V
Outputs power transistor With ignition switch ON (II) and fan
22 YEL BLOWER_G
gate voltage control dial ON: about 4.0 V－battery
voltage (depending on blower motor
control)

Not
23 Not used ――― ―――
used

With ignition switch ON (II): about 0 V


Feedback signal of power
24 BLU BLOWER_V －battery voltage (depending on
transistor drain voltage
blower motor speed)

Not
25 Not used ――― ―――
used

26 BRN RR_DEF_RLY_CL- Signal for rear window With ignition switch ON (II) and rear
defogger relay window defogger button OFF: battery
voltage
With ignition switch ON (II) and rear
window defogger button ON: about 0
V

With ignition switch ON (II), normal A/C


pressure, and A/C switch OFF: battery

*1
voltage
27 BLU THERMAL_PRT Outputs A/C on/off signal
With ignition switch ON (II), normal A/C
pressure, and A/C switch ON: less than
0.2 V

With ignition switch ON (II), normal A/C


pressure, and A/C switch OFF: battery
voltage
27 *2 RED ACS Outputs A/C on/off signal
With ignition switch ON (II), normal A/C
pressure, and A/C switch ON: less than
0.2 V

With ignition switch ON (II) and when


HAC CUT control is prohibited: battery
Outputs A/C off permit voltage
28 BLU A/C_CUT
signal With ignition switch ON (II) and when
HAC CUT control is permitted: less
than 0.2 V

Not
29 Not used ――― ―――
used

With ignition switch ON (II) and ECON


OFF mode: battery voltage
30 PNK ECON_SW Inputs ECON control signal
With ignition switch ON (II) and ECON
ON mode: less than 1.0 V
Not
31 Not used ――― ―――
used

With ignition switch ON (II): about 1.0－


Detects evaporator
32 BRN TEVA 4.0 V (depending on evaporator
temperature sensor signal
temperature)

*1: USA and Canada models


*2: Mexico models

You might also like