INTERNATIONAL SERIES PROGRAMMING GUIDE

DIGITAL MONITORING PRODUCTS, INC.

 MODEL XR150INT/XR550INT SERIES
PROGRAMMING GUIDE

Contains programming instructions for use with the

Model XR150INT/XR550INT Series Control Panels.

When using the XR150INT/XR550INT Series panel for any listing organization’s approved methods, refer
to the Compliance Listing Guide (LT-1330INT). This document outlines the installation and programming
requirements of all applications for which XR150INT/XR550INT Series control panels are approved.

© 2024 Digital Monitoring Products, Inc.

Information furnished by DMP is believed to be accurate and reliable.

This information is subject to change without notice.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

INTRODUCTION......................................1 Test Report ............................................................................ 7

XR International Series Programming Test Frequency ..................................................................... 7

Information ............................................................................ 1
Test Day................................................................................... 7
Getting Started .................................................................... 1
Test Time................................................................................. 7
Accessing the User Menu ................................................. 1
Check In .................................................................................. 7
Encrypted Communications (XR550INT with
Encryption Only) ................................................................. 1 Fail Time.................................................................................. 7

Programmer Operation ..................................................... 2 Encryption (XR550INT with Encryption Only)........ 7

Programmer Lockout Codes........................................... 2 IPV6 Address ........................................................................ 8

Reset Timeout ...................................................................... 2 Receiver IP ............................................................................. 8

Keypads .................................................................................. 3 Receiver Port ........................................................................ 8

Special Keys........................................................................... 3 First Telephone Number ................................................... 8

Entering Alpha Characters .............................................. 3 Second Telephone Number ............................................. 8

Entering Non-Alpha Characters .................................... 4 APN ........................................................................................... 8

Keypad Displays Current Programming..................... 4 Fail Test Hours ...................................................................... 8

Multiple Displays .................................................................. 4 Protocol ................................................................................... 8

Asterisks in Programming ................................................ 4 Retry Seconds ...................................................................... 8

Compliance Instructions ................................................... 4 Substitution Code ............................................................... 9

893A ......................................................................................... 9
INITIALIZATION......................................5
Alarm Switch ......................................................................... 9
Initialization ........................................................................... 5
Duplicate Alarms ................................................................. 9
Clear All Memory ................................................................. 5
Alarm Reports ...................................................................... 9
Clear All Codes..................................................................... 5
Supervisory/Trouble Reports ......................................... 9
Clear All Schedules............................................................. 5
Opening/Closing and User Reports ............................. 10
Clear Display Events Memory......................................... 5
Door Access Report ........................................................... 10
Clear Zone Information ..................................................... 5
Panic Test (Network Only)............................................... 10
Clear Area Information...................................................... 5
Send Communication Trouble ........................................ 10
Clear Output Information................................................. 5
Send Path Information ...................................................... 10
Clear Communication and Remote Options............. 5

Clear Wi-Fi ............................................................................. 5 NETWORK OPTIONS..............................11

Set to Factory Defaults ..................................................... 5 Wi-Fi Setup ............................................................................ 11

WPS .......................................................................................... 11
COMMUNICATION ..................................6
List............................................................................................. 11
Communication .................................................................... 6
Manual ..................................................................................... 11
Account Number ................................................................. 6
Test ............................................................................................ 12
Transmit Delay ...................................................................... 6
Wireless Security Type ...................................................... 12
Communication Path ......................................................... 6
Wireless Network Key ....................................................... 12
Communication Type ......................................................... 6
IPV6 .......................................................................................... 12

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

i
 DHCP........................................................................................ 12 Program 734INT Options ................................................. 20

Local IP Address ................................................................. 12 Activate Zone 2 Bypass .................................................... 20

Gateway Address ................................................................ 12 Zone 2 Bypass Time ........................................................... 20

Subnet Mask .......................................................................... 12 Relock on Zone 2 Change?.............................................. 20

DNS Server............................................................................. 12 Activate Zone 3 Request to Exit ................................... 20

Passphrase (XR550INT with Encryption Only) ....... 13 Zone 3 REX Strike Time .................................................... 20

DEVICE SETUP ........................................14 REMOTE OPTIONS .................................21

Device Setup ......................................................................... 14 Remote Options................................................................... 21

Custom Card Denitions .................................................. 14 Remote Key ........................................................................... 21

Wiegand Code Length ...................................................... 14 Remote Disarm..................................................................... 21

Site Code Position............................................................... 14 Armed Answer Rings ......................................................... 21

Site Code Length................................................................. 14 Disarmed Answer Rings ................................................... 21

User Code Position ............................................................. 14 PC Modem .............................................................................. 21

User Code Length ............................................................... 14 Alarm Receiver Authorization ........................................ 21

Require Site Code ............................................................... 14 Service Receiver Authorization ..................................... 21

Number of User Code Digits........................................... 15 Manufacturer Authorization ............................................ 22

Device Number .................................................................... 15 Allow Network Remote ..................................................... 22

Device Name ......................................................................... 16 Network Programming Port ............................................ 22

Device Type ........................................................................... 16 Encrypt Network Remote ................................................ 22

Private Door .......................................................................... 16 Allow Cellular Remote ....................................................... 22

Device Communication Type.......................................... 16 APN ........................................................................................... 22

Serial Number ....................................................................... 17 Encrypt Cellular Remote .................................................. 22

Supervision Time ................................................................. 17 Entré Connection ................................................................ 22

Access Areas ......................................................................... 17 Entré Incoming TCP Port.................................................. 22

Egress Areas.......................................................................... 17 Entré IP Address .................................................................. 22

Display Areas ........................................................................ 17 Entré Outbound TCP Port................................................ 22

Strike Time ............................................................................. 18 Entré Backup Connection ................................................ 23

Strike Delay............................................................................ 18 Entré Backup TCP Port ..................................................... 23

Fire Exit Release .................................................................. 19 Entré Reports ........................................................................ 23

Public Door ............................................................................ 19 Arm and Disarm Reports ................................................. 23

Output Group ....................................................................... 19 Zone Reports ........................................................................ 23

Schedule Override .............................................................. 19 User Command Reports ................................................... 23

Auto Force Arm Device? .................................................. 19 Door Access Reports ......................................................... 23

Door Real-Time Status? .................................................... 19 Supervisory Reports .......................................................... 23

PIN Disarm? ........................................................................... 19 Video Reports ....................................................................... 23

Send Door Forced Message? .......................................... 19 Entré Checkin ....................................................................... 23

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

ii
 Entré Passphrase ................................................................. 23 System ..................................................................................... 29

Integrator Connection ....................................................... 24 Instant Arming...................................................................... 29

Integrator Incoming TCP Port ........................................ 24 Closing Wait .......................................................................... 29

Integrator IP Address......................................................... 24 Entry Delay 1.......................................................................... 29

Integrator Outbound TCP Port ...................................... 24 Cross Zone Time.................................................................. 30

Integrator Backup Connection....................................... 24 Zone Retard Delay .............................................................. 30

Integrator Backup TCP Port ............................................ 24 Power Fail Delay .................................................................. 30

Integrator Reports .............................................................. 24 Swinger Bypass Trips ......................................................... 30

Arm and Disarm Reports ................................................. 24 Reset Swinger Bypass ....................................................... 30

Zone Reports ........................................................................ 24 Zone Activity Hours ........................................................... 30

User Command Reports ................................................... 24 Time Zone Changes............................................................ 31

Door Access Reports ......................................................... 24 Latch Supervisory Zones.................................................. 31

Supervisory Reports .......................................................... 25 Programming Menu Language....................................... 31

Integrator Passphrase........................................................ 25 User Menu and Status List Language.......................... 32

Send Local Changes........................................................... 25 Bypass Limit .......................................................................... 32

Remote Change IP .............................................................. 25 House Code ........................................................................... 32

Remote Change Port ......................................................... 25 Wireless Encryption ........................................................... 32

Remote Telephone Number ............................................ 25 Enter Passphrase ................................................................. 32

App Key .................................................................................. 25 Detect Wireless Jamming ................................................ 33

Activate Onboard Speaker .............................................. 25 Trouble Audible Annunciation ....................................... 33

Card Options ......................................................................... 26 Enable Keypad Panic Keys .............................................. 33

Require Site Code (If Card Format Occupied Premises ............................................................. 33

is Set to DMP) ....................................................................... 26
Enhanced Zone Test ........................................................... 33
No Communication with Panel ...................................... 26
Send 16 Character Names ................................................ 33

SYSTEM REPORTS ..................................27 Keypad Armed LED............................................................ 34

System Reports .................................................................... 27 Use False Alarm Question................................................ 34

Abort Report ......................................................................... 27 Allow Own User Code Change ...................................... 34

Restoral Reports .................................................................. 27 Panic Supervision ................................................................ 34

Bypass Reports .................................................................... 27 EOL Selection ....................................................................... 34

Schedule Change Reports ............................................... 27 Celsius Temperature Option ........................................... 34

Access Keypads ................................................................... 27 Intruder Conrmation Time............................................. 35

Ambush ................................................................................... 27 Hold Up Conrmation Time ............................................ 35

Late To Open......................................................................... 28
BELL OPTIONS........................................36
Early To Close ....................................................................... 28
Bell Options ........................................................................... 36

SYSTEM OPTIONS ..................................29 Bell Cuto Time ................................................................... 36

System Options .................................................................... 29 Automatic Bell Test ............................................................ 36

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

iii
 Bell Output............................................................................. 36 Lockdown Output Alarm Output.................................. 39

Bell Action .............................................................................. 36

OUTPUT INFORMATION ........................40
Fire Bell Action ..................................................................... 36
Output Number.................................................................... 40
Burglary Bell Action ........................................................... 36
Output Name ........................................................................ 40
Supervisory Bell Action .................................................... 36
Output Real-Time Status .................................................. 40
Panic Bell Action.................................................................. 36
Serial Number ....................................................................... 40
Emergency Bell Action ..................................................... 36
Supervision Time ................................................................. 40
Auxiliary 1 Bell Action ........................................................ 36
Trip with Panel Bell Option .............................................. 40
Auxiliary 2 Bell Action ....................................................... 36

Carbon Monoxide (CO) ..................................................... 36

OUTPUT GROUPS ...................................41
Output Groups ..................................................................... 41
Strobe ...................................................................................... 36
Group Number...................................................................... 41
OUTPUT OPTIONS ..................................37
Group Name .......................................................................... 41
Output Options .................................................................... 37
Output Number.................................................................... 41
Cuto Output ....................................................................... 37

Output Cuto Time ............................................................ 37

MENU DISPLAY .......................................42
Menu Display ......................................................................... 42
Communication Trouble Output ................................... 37
Armed Status ........................................................................ 42
Fire Alarm Output............................................................... 37
Time .......................................................................................... 42
Fire Trouble Output ............................................................ 37
Arm/Disarm ........................................................................... 42
Panic Alarm Output............................................................ 38

Ambush Output ................................................................... 38 STATUS LIST ............................................43

Entry Output ......................................................................... 38 Status List............................................................................... 43

Begin Exit Output ............................................................... 38 Display Keypads .................................................................. 43

End Exit Output ................................................................... 38 System Monitor Troubles.................................................. 43

Ready Output ....................................................................... 38 Fire Zones............................................................................... 43

Armed Output ...................................................................... 38 Burglary Zones ..................................................................... 43

Disarmed Output ................................................................. 38 Supervisory Zones .............................................................. 44

Telephone Trouble Output ............................................... 38 Panic Zones ........................................................................... 44

Late To Close Output ......................................................... 38 Emergency Zones ............................................................... 44

Device Fail Output .............................................................. 39 Auxiliary 1 Zones .................................................................. 44

Sensor Reset Output ......................................................... 39 Auxiliary 2 Zones................................................................. 44

Closing Wait Output .......................................................... 39 Carbon Monoxide Zones .................................................. 44

Arm-Alarm Output.............................................................. 39 Communication Trouble ................................................... 44

Supervisory Alarm Output .............................................. 39

PC LOG REPORTS...................................45
Heat Saver Temperature ................................................... 39
PC Log Reports.................................................................... 45
Cool Saver Temperature ................................................... 39
Net IP Address...................................................................... 45
Carbon Monoxide Alarm Output................................... 39
Net Port ................................................................................... 45
Digital Monitoring Products XR150INT/XR550INT Series Programming Guide
iv
 Arm and Disarm Reports ................................................. 45 Zone Number........................................................................ 51

Zone Reports ........................................................................ 45 Zone Name ............................................................................ 51

User Command Reports ................................................... 45 Area Assignment ................................................................. 52

Door Access Reports ......................................................... 45 Number of EOL .................................................................... 52

Supervisory Reports .......................................................... 45 Fire Bell Output.................................................................... 53

PC Log Real-Time Status .................................................. 46 Arming Zone Area Assignment ..................................... 53

Style .......................................................................................... 54
AREA INFORMATION .............................47
Expander Serial Number .................................................. 54
Area Information ................................................................. 47
Next Zone............................................................................... 54
Exit Delay ............................................................................... 47
Wireless ................................................................................... 54
Closing Check ....................................................................... 47
Serial Number Entry ........................................................... 55
Closing Code ......................................................................... 47
Contact .................................................................................... 55
Any Bypass ............................................................................ 47
Supervision Time ................................................................. 55
Area Schedules .................................................................... 47
LED Operation ...................................................................... 55
Early Morning Ambush (Network Panels Only) ...... 48
Disarm/Disable..................................................................... 55
Area Number......................................................................... 48
PIR Pulse Count ................................................................... 56
All/Perimeter Programming............................................ 48
PIR Sensitivity....................................................................... 56
Home/Sleep/Away Programming................................. 48
Pet Immunity ......................................................................... 56
Area Name ............................................................................. 48
Next Zone ............................................................................... 56
Account Number ................................................................. 48
Alarm Action ......................................................................... 56
Opening/Closing Reports ................................................ 48
Disarmed Open .................................................................... 56
Automatic Arming .............................................................. 49
Report to Transmit .............................................................. 56
Bad Zones .............................................................................. 49
Output Number.................................................................... 57
Automatic Disarming ......................................................... 49
Output Action ....................................................................... 57
Burglary Bell Output .......................................................... 49
Disarmed Short, Armed Open, and
Armed Output Number .................................................... 49 Armed Short.......................................................................... 57
Late Output Number.......................................................... 49 Swinger Bypass .................................................................... 57

Late Arm Delay .................................................................... 49 Prewarn Keypad Addresses ............................................ 58

Bank Safe & Vault (XR550INT with Network or Chime ....................................................................................... 58

Encryption Only) ................................................................. 50
Entry Delay ............................................................................ 58
Common Area ...................................................................... 50
Zone Retard Delay .............................................................. 58
Arm First Area ...................................................................... 50
Presignal Keypad Addresses .......................................... 58
Dual Authority (XR550INT with Network or
Encryption Only) ................................................................. 50 Fast Response ...................................................................... 58

Card Plus Pin (XR550INT with Network Cross Zone ............................................................................. 58

or Encryption Only)............................................................ 50
Priority ..................................................................................... 58

ZONE INFORMATION .............................51 Fire Panel Slave Input ........................................................ 59

Zone Information ................................................................. 51 Area Follower........................................................................ 59

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

v
 Zone Real-Time Status ...................................................... 59 Keypad Displays .................................................................. 71

Trac Count .......................................................................... 59 Using the Walk Test ............................................................ 71

Zone Audit Days .................................................................. 59 Walk Test ................................................................................ 72

Report with Account Number for Area ...................... 59 Zone Types ............................................................................ 72

Lockdown............................................................................... 59 Trip Counter For Walk Test.............................................. 73

1144INT Series Key Fobs ................................................... 60 Trip Counter For DMP Wireless Check-in Test
(WLS) ....................................................................................... 73
Key Fob User Number ....................................................... 60
Test End Warning ................................................................ 73
Key Fob Serial Number ..................................................... 60
Wireless Check-in and Supervision Denitions ....... 74
Key Fob Supervision Time ............................................... 60
Keypad Speaker Operation ............................................. 74
Number of Key Fob Buttons ........................................... 60
Cross Zoning ......................................................................... 74
Key Fob Button Selection (Four Buttons)................. 60
User Proles .......................................................................... 74
Key Fob Button Selection (Two Buttons) .................. 60
User Proles Record........................................................... 75
Button Action ....................................................................... 61
Zone Type Descriptions .................................................... 75
Button Press Time ............................................................... 61
Common Keypad Messages ............................................ 77
Arm/Disarm Area Selection ............................................ 61
Area Account Number Messages.................................. 78
Output Number.................................................................... 61

Output Action....................................................................... 62 SPECIFICATIONS ....................................79

STOP .........................................................63 INTERNATIONAL CERTIFICATIONS ....79

Stop .......................................................................................... 63 Intertek (ETL) Listed .......................................................... 79

SET LOCKOUT CODE .............................64

Set Lockout Code ............................................................... 64

FEATURE UPGRADE...............................65
Feature Upgrade ................................................................. 65

Encryption.............................................................................. 65

All No Yes Option................................................................ 65

Service User Authentication ........................................... 65

32 Door Add On A/ 32 Door Add On B ..................... 65

EN 50131 GRADE ....................................66

EN 50131 Grade .................................................................... 66

APPENDIX................................................67
False Alarm Reduction ...................................................... 67

Anti-masking feature ......................................................... 67

Diagnostics Function ......................................................... 67

Using the 984 Command Function .............................. 71

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

vi
INTRODUCTION
XR INTERNATIONAL SERIES PROGRAMMING INFORMATION
This guide provides programming information for the DMP XR150INT/XR550INT Series panel. Before starting to
program, we recommend that you read through the contents of this guide.

In addition to this guide, you should also read and be familiar with the following documents:

• XR150INT/XR550INT Series Installation Guide (LT-1233INT)

• XR150INT/XR550INT Series Programming Sheet (LT-1234INT)

• XR150INT/XR550INT Series Users Guide (LT-1278INT)

Internal Programmer
The panel contains all of its programming information in an on-board processor and does not require an external
programmer. You can perform all programming tasks through a 32-character DMP alphanumeric keypad set to address
one, or through Dealer Admin, Tech APP, and Remote Link.

GETTING STARTED
Before starting to program the panel, make sure the panel is properly grounded and AC and battery power is applied
to the appropriate panel terminals. All wiring connections and grounding instructions are detailed in the XR150INT/
XR550INT Series Installation Guide (LT-1233INT).

ACCESSING THE USER MENU

XR International Series panels ship with a unique ve-digit default master code
that is used to access the user menu for the rst time. This code can be modied MAC : 00:01:22:33:44:55
MOD : DUALCOM
or deleted. In order to revert back to the default master code, use the initialize VER : 194 122319 Example Default
code option found in panel programming. To access the User Menu: SN : 0012345A CODE21852
Master Code
TD : 011520
KEY : 100
1. Press the CMD key until MENU? NO YES displays.
2. Select YES. The keypad displays ENTER CODE. Enter your user code.
You can now scroll down through the list of system features available to
you.

BEGIN A PROGRAMMING SESSION

1. Momentarily place the Reset jumper over both of the RESET pins to reset the panel.
2. Enter the code 6653 (PROG) and press CMD.
3. The keypad displays: PROGRAMMER.

ENCRYPTED COMMUNICATIONS (XR550INT WITH ENCRYPTION ONLY)

Some installations require secure data communications. Use a unique passphrase to enable encrypted communications
and provide a secure means for data communications. See Network Options.

An XR550INT panel with encryption communicates using 128-bit or 256-bit AES encryption. If you currently have an
XR550INT panel with network installed, you may purchase a separate feature key to activate encrypted communications
using the Feature Upgrade process. Encrypted communication cannot be enabled on a standard XR550INT panel. For
more information on the Feature Upgrade process see Section 21 in this document.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

1
PROGRAMMER OPERATION
There are 20 programming sections to choose from:

Programming Item Section in This Manual Programming Item Section in This Manual
Initialization 2 Output Information 12
Communication 3 Output Groups 13
Network Options 4 Menu Display 14
Device Setup 6 PC Log Reports 16
Remote Options 7 Area Information 17
System Reports 8 Zone Information 18
System Options 9 Stop 19
Bell Options 10 Set Lockout Code 20
Output Options 11 Feature Upgrade 21

To choose a section for programming, press any select key or area when the keypad displays the name of that section.
Sections 2 through 21 contain detailed instructions for each programming step.

PROGRAMMER LOCKOUT CODES

The panel allows you to enter the programming function without entering a lockout code using steps 1 to 4 listed in
Getting Started. We recommend, however, that you install a Lockout Code to restrict programming to only those persons
your company authorizes. You can do this by using the SET LOCKOUT CODE feature in the Programmer. The Lockout
Code restricts any unauthorized panel programming.

After resetting the panel and entering the code 6653, the keypad displays PROGRAMMER. Press CMD to advance
through the programming sections until SET LOCKOUT CODE displays (after STOP). Press any select key or area. The
keypad displays ENTER CODE: – . Enter a 3 to 5 digit Programmer Lockout Code and press CMD. The keypad displays
ENTER AGAIN followed by ENTER CODE: –. Enter the same 3 to 5 digit code a second time and press CMD. The keypad
displays CODE CHANGED. The panel does not accept a 5-digit Lockout Code higher than 65535.

Before accessing programmer functions enter the new code number. Write the Lockout Code number down and keep it
in a secure place with access limited to authorized persons only. Lost Lockout Codes require the panel to be sent back to
DMP for repair. You may cancel a Lockout Code by entering 00000 at the Set Lockout Code command.

RESET TIMEOUT
The panel has a feature that requires you to enter the Programmer within 30 minutes of resetting the panel. After 30
minutes, if you attempt to program by entering the 6653 (PROG) code, the keypad displays: RESET PANEL. You must
reset the panel and enter the program code then begin programming within the next 30 minutes.

If you are already in the Programmer and do not press any keys on the programming keypad for 30 minutes, the panel
terminates programming. All data entered up to that time is not saved unless you run the Stop routine.

Use the Stop routine to exit panel Programming. Ensure the keypad displays “SAVING PROGRAM” to save all
programming changes entered.

POWER UP
When the panel is powered up after an AC power failure, any zone transitions are not recognized for 60 seconds. Normal
zone processing resumes at the end of the 60 seconds.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

2
KEYPADS
DMP oers multiple keypads in a variety of styles that provide programming capabilities.

SPECIAL KEYS
The following special keys/areas are common to all DMP keypads.

COMMAND (CMD) Key

Pressing CMD allows you to go forward through the programming menu and through each step of a programming sec-
tion. As you go through the programming, the keypad display shows any current programming already stored in the
panel memory. If no change is required for an option, press CMD to advance to the next step.

CMD is also used to enter information into the panel’s memory such as phone numbers or zone names. Press CMD after
entering information.

Back Arrow (<—) Key

Use the Back Arrow key to back up one step while programming. The Back Arrow key is also used when an error is made
while entering information. Press the Back Arrow key once to erase the last character entered.

Select Keys or Areas

The top row of keys are called the select keys on Thinline and Aqualite keypads or select areas on Graphic Touchscreen
keypads. Each time you need to press a select key or area, the keypad displays the function or options above one of the
keys or in the select area. Displaying choices above individual select keys or in select areas allows them to be used for
many dierent applications. For example, you can enter AM or PM when programming the automatic test time or answer
YES or NO for a system option.

During programming, the select keys or areas also allow you to change information currently in panel memory by
pressing the appropriate select key or area under or on the display. You then enter the new information using the keypad
data entry digit keys.

When there are more than four response options available, press CMD to display the remaining options. Pressing the
Back Arrow key allows you to review the previous four choices.

The select keys or areas are also used for choosing a section from the programming menu. Press any select key or touch
the select area when the programming section name you want displays.

On Wireless, Thinline and Aqualite keypads, when instructed to press the rst select key, press the far left select key; the
second select key is the second from the left; third select key is second from the right; and the fourth select key is the far
right key.

On Graphic Touchscreen Keypads, when instructed to press the rst select key, touch select area 1; the second select key
touch select area 2; third select key touch select area 3; and the fourth select key touch select area 4.

ENTERING ALPHA CHARACTERS

Some options during programming require you to enter alpha characters. To enter an alpha character, press or touch
the key that has that letter written below it. The keypad displays the number digit of the key. Next, press the select key
or area that corresponds to the location of the letter under the key. Pressing a dierent select key or area changes the
letter. When another digit key is pressed, the last letter displayed is retained and the process starts over.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

3
ENTERING NON-ALPHA CHARACTERS
To enter a space in an alpha entry, press the 9 digit key followed by the third select key or area. The three characters on
the 9 digit key are Y, Z, and space. You can also enter the following characters: – (dash), . (period), * (asterisk), and #
(pound sign) using the 0 (zero) key and the four select key or area from left to right. For example, to enter a – (dash),
press the 0 (zero) key and then the left select key or area. A dash now appears in the keypad display. The table below
shows the character locations for DMP keypads.

Key Number Select Key or Select Key or Select Key Select Key or
Area 1 Area 2 or Area 3 Area 4
1 A B C (
2 D E F )
3 G H I !
4 J K L ?
5 M N O /
6 P Q R &
7 S T U @
8 V W X ,
9 Y Z space _
0 - . * #

KEYPAD DISPLAYS CURRENT PROGRAMMING

Each programming option displayed at the keypad shows the currently selected option in the panel memory. These
options are either shown as a number, a blank, or a NO or YES. To change a number or blank to a new number, press any
select key or touch any select area. The current option is replaced with a dash.

Press the number(s) on the keypad you want to enter as the new number for that option. It is not necessary to enter
numbers with leading zeros. The panel automatically right justies the number when you press CMD.

To change a programming option that requires a NO or YES response, press the select key or touch the select area for
the response not selected.

For example, if the current option is selected as YES and you want to change it to NO, on Thinline or Aqualite keypads
press the third select key. On Graphic Touchscreen keypads touch select area 3. The display changes to NO. Press CMD
to display the next option.

MULTIPLE DISPLAYS
For many programming and user options, such as Area selections, Menu Displays, and Status Lists, there are several
displays containing programming. For example, when programming Menu Displays, keypads 1 through 16 display on two
separate displays. First, keypads 1 through 8 display. Press CMD to display keypads 9 through 16. This same scheme is
used for areas 1 through 32. Areas not pre-programmed at installation to display at this keypad cannot be viewed.

ASTERISKS IN PROGRAMMING
Asterisks display next to a programming option that is already selected. As shown in the example, options that are
selected to display the current programming selection have an asterisk next to the number. Those that are not selected
simply display the number. In the Devices example, keypads 3, 8, 9, and 15 are not selected. In the Areas example, areas
3, 8, 9, 15, 19, 23, 25, and 31 are not selected. In both examples the numbers with asterisks are selected.

To select or deselect a number, simply enter the number using the digit keys on the keypad. This same scheme is used
when viewing the panel armed status and other programming and operational functions. Remember to press CMD to
display the rest of the device or area numbers.

COMPLIANCE INSTRUCTIONS
This product incorporates eld-programmable software. Refer to the XR150INT/XR550INT Compliance Listing Guide
(LT-1330INT) for additional compliance information.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

4
INITIALIZATION
Initialization
INITIALIZATION This function allows you to clear selected parts of the panel program back to the factory
defaults.

Clear All Memory

INIT ALL? NO YES NO leaves existing programming intact then displays Clear All Codes.
YES clears all memory then displays Reset Panel. Reset the panel by shorting the reset
jumper and re-enter programming mode to continue.

Clear All Codes

CODES? NO YES NO leaves existing codes intact.
YES clears the user code and user prole memory and assigns user code number 99 to the
highest user number.

Clear All Schedules

SCHEDS? NO YES NO leaves existing schedules intact.
YES clears all shift and output schedules.

Clear Display Events Memory

EVENTS? NO YES NO leaves existing event memory intact.
YES clears the events memory.

Clear Zone Information

ZONES? NO YES NO leaves existing zone information intact.
YES clears the zone information for all zones.

Clear Area Information

AREAS? NO YES NO leaves existing area information intact.
YES clears the area information for all areas.

Clear Output Information

OUTPUTS? NO YES NO leaves existing output information intact.
YES clears all programmed output names and any output cuto assignment.

Clear Communication and Remote Options

COM/RMT? NO YES NO leaves existing communication and remote options intact.
YES reset communication and remote options programming to factory defaults.

Clear Wi-Fi
WIFI? NO YES NO leaves existing Wi-Fi programming intact.
YES reset Wi-Fi programming to factory defaults.

Set to Factory Defaults

DEFAULTS NO YES NO leaves existing panel programming intact.
YES sets the panel’s programming back to factory default selections and clears all
Favorites, Device Setup, System Options, and Remote Options programming from the
panel. Selecting YES does not clear the panel’s event memory, zone, user code information,
or schedules.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

5
COMMUNICATION
Communication
COMMUNICATION Congure the communication options for the panel. The information you program varies
with the Communication Type you select.

Account Number
ACCOUNT NO: 12345 The Account Number is a 1 to 5 digit number used to identify which panel is sending a
message. Enter the account number sent to the SCS-1R or SCS-VR Receiver. The default is
12345.
The range of valid account numbers for a panel is 1 to 65535. For accounts of four digits or
less, do not enter leading zeros.

Transmit Delay
XMIT DELAY: 30 Enter the number of seconds (15 to 45) the panel waits before sending burglary zone
(Night, Day, or Exit) reports to the receiver. Other zone type reports are sent immediately.
Alarm bells and relay outputs are not delayed during this period. Program Burglary
Outputs for pulsed or steady, and set Abort Reports to YES if Opening and Closing reports
are not being sent. Enter 0 (zero) to disable this function. The default is 30.
If the area where the alarm occurred is disarmed during the Transmit Delay time, only an
Abort Report (S45) message is sent to the receiver. If the area where the alarm occurred
is disarmed after the alarm message is sent to the receiver but before the Bell Cuto
time expires even if the alarm was silenced, an Alarm Cancelled (S49) message is sent.
Otherwise the alarm is sent at the end of the delay.

Communication Path
PATH: - Up to eight communication paths may be programmed. Each path is designated as a
primary or backup communication route. Path 1 is always Primary but other paths may be
programmed as additional primary or backup.
Each primary path establishes a new path group. A path group is made up of the primary
path and its subsequent backup paths. Typical communication takes place on the primary
path with backup paths being used only when the primary path fails or when the backup
path is programmed to duplicate messages. There is no option to backup path 8.

Communication Type
COMM TYPE: NONE Species the communication method the panel uses on this path to report system events
to DMP SCS-1R or SCS-VR Receivers. Default is NONE for Path 1-8.
NONE - For local systems. Selecting NONE ends communication programming.
DD - Digital Dialer communications to a DMP SCS-1R Receiver.
NONE DD NET CID
NET - Network communication using the panel onboard network connection. The DMP
Network/Output reporting format is transmitted over a data network to the SCS-1R or
SCS-VR Receiver.
CID - This option allows the panel to communicate to DMP and non-DMP receivers using
the Contact ID format.
CELL - This option allows communication over the cellular network using the 263LTE
CELL WIFI Cellular Communicator.
WIFI - Network communication to DMP Model SCS-1R or SCS-VR Receivers.

PATH TYPE: BACKUP Path Type

PRIMARY BACKUP The Path Type denes if the path is Primary or Backup. Because Path 1 is Primary, this
option only displays for paths 2-8. Default is BACKUP.
If the Primary Communication Type is CELL, then the backup Communication Type can
only be NET.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

6
TEST RPT: YES Test Report
NO YES DEFER Test Report determines if test reports (Automatic Recall Test OK or Unrestored System) are
sent on this path. Reports are sent according to the programming in Test Frequency and
Test Time. Default is YES.
Select YES to allow the programmed test report to be sent on the path currently being
programmed.
Select DEFER to not send a test report if the panel communicates any message to the
receiver within the time set in Test Frequency.
Select NO to not send test reports on this path.

Test Frequency
TEST FREQ: 1 DY Test Frequency determines the frequency of the test report. Enter a number from 1 to 60
and select DY (Day) or HR (Hour) by pressing the far right select key or area. Default is 1
Day.

Test Day
TEST DAY: SUN Use this option to set the day of the Test Report. This option appears only when Test Report
is Yes, Test Frequency is Day and a multiple of seven. Press CMD to display the rst four
days of the week. Press CMD to display the last three days. Select the day of the week to
send the test report. Default is SUNDAY.

TEST TIME: Test Time

0:00 AM Use this option to select the time of day for Test Reports. Select the hour, minute and AM/
PM. Enter 0:00 AM to disable this feature. Default is 0:00 AM.

Check In
TEST DAY: SUN This option displays if the COMM TYPE is NET, WIFI, or CELL. Check-in reports are a
method of supervising the panel for communication with the receiver. For NET the default
is YES. For CELL the default is YES.

CHECKIN Select RND (Random) for the panel to check-in at random times from 6 to 60 minutes when
NO YES RND ADPT all areas are disarmed. If any area is armed a check-in is sent every 6 minutes.

Select ADPT (Adaptive) for a backup path to adapt to the check-in programming from
this groups primary path if the primary path becomes unavailable. Check-in programming
includes Check-in and Fail Time.

Select ADP3 (Adaptive 3) for a backup path to adapt using a 3 minute Check-in and Fail
CHECKIN
Time if the primary path becomes unavailable. This option also indicates a Communication
ADP3
Trouble (S10) if the cell tower is unavailable for 3 minutes.

When YES is selected, enter the number of minutes between check-in reports, from 2 to
CHECKIN MINS: 200 240 for NET or 3 to 240 for CELL, when the panel is armed or disarmed. For CELL the
default is 0. For NET the default is 200.

Fail Time
FAIL MINS: 240 This option displays if CHECKIN is set to YES. Entering a FAIL TIME allows the receiver to
miss multiple check-ins before logging that the panel is missing. The maximum fail time is
240 minutes. For example, if CHECKIN is 10 and FAIL TIME is 30, the receiver only indicates
a Panel Not Responding after 30 minutes. The FAIL TIME must be equal to or greater than
the CHECKIN time. Default is equal to CHECKIN for CELL. Default is 240 for NET.

ENCRYPT: NO Encryption (XR550INT with Encryption Only)

NO 128 256 This option displays if the Communication Type is NET or CELL. Select 128 or 256 to enable the
encryption level for the path currently being programmed. Default is NO.
256-bit encrypted messages to the SCS-1R receiver only communicate when using SCS-104
Receiver Line Cards with Version 102 or higher software.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

7
USE IPV6: IPV6 Address
NO YES This prompt determines if the network path uses IPV6 for communication. Default is NO.

RECEIVER IP Receiver IP
000.000.000 This option displays if the Communication Type is NET or CELL. Enter the Receiver IP
address where the panel sends network messages. The Receiver IP Address must be
unique and cannot be duplicated on the network. Enter all 12 digits and leave out the
periods. For example, enter IP address 192.168.0.250 as 192168000250. The periods
display automatically. If IPV6 is selected the receiver IP will need to be an IPV6 address. If
changing from IPV6 YES to IPV6 NO, you will need to modify their IP address to IPV4.

RECEIVER PORT Receiver Port

2001 Enter the receiver port number. Valid range is 1 to 65,535. Default is 2001.

First Telephone Number

FIRST PHONE NO: This option displays only if the Communication Type is DD or CID.
This is the rst number the panel dials when sending reports to the receiver. Phone
numbers can have two lines of 16 characters each to equal up to 32 characters.

Second Telephone Number

SECOND PHONE NO: The panel dials the second number when two successive tries using the rst number fail. If
the panel cannot reach the receiver after two attempts using the second number, it returns
to the rst number and makes two additional attempts. A total of ten dialing attempts are
made using the rst and second phone numbers.

Advanced Programming
ADVANCED? NO YES Select YES to enter the Advanced Programming menu for the communication
path currently being programmed. Selecting NO ends programming of the current
communication path and takes users back to the Communication Path option to program a
secondary path.

APN APN
SECURECOM400 Enter the rst APN (Access Point Name). This allows an access point for cellular
communication and is used to connect to a DNS network. The APN may contain two lines
of 16 characters to equal 32 characters. Default is set to SECURECOM400.

Fail Test Hours

FAIL TEST HRS: 0 This option sets the frequency for a Backup or Adaptive path to send a test report when
the closest previous path fails within its path group.
If Fail Test Frequency is set to 0, test reports are sent only according to Test Report
programming. Range is 0 to 24 hours. Default is 0.

Protocol
PROTOCOL: TCP This option displays only if Communication Type is NET.
Select TCP to communicate over the network using TCP protocol. Select UDP to
communicate using UDP protocol. Default is TCP.

Retry Seconds
RETRY SECONDS: 6 This option displays only when Communication type is NET.
Enter the number of seconds (between 6 and 15) the panel should wait before retrying to
send a message to the receiver if an acknowledgment was not received. The panel retries
as many times as possible for a period of one minute before sending a network trouble
message. The default Retry Time is 6 seconds.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

8
SUB CODE: NO Substitution Code
NO YES SHARED This option displays when the Communication Type is NET or CELL. The Panel Substitution
Code increases the level of security by helping to ensure that the panel sending the
message to the receiver has not been substituted by another panel. The default is NO.
Select YES to send a substitution code with every message.
Select SHARED (SHR) to use the same substitution code that was used in the previous
path.

893A
893A: NO YES This option displays when the Communication Type is DD or CID.
The 893A option allows reports to be sent to the receiver on a second DD line using the
893A module. Default is NO.
When using an 893A, Test Report messages (S07 Automatic Recall Test or S88
Unrestored System Recall Test) are sent to the receiver at the frequency programmed in
Test Frequency, alternating between the rst and second phone line.

Alarm Switch
ALARM SWITCH: 1 This option displays only if using the DD or CID Communication Types.
Enter the number of attempts to send an alarm message before switching to the next path.
Range is from 1 to 10. All non-alarm messages are sent for 10 attempts on the dialer before
a switch is initiated. If the path immediately following this channel is not a backup path, this
option has no eect. Default is 1.

Duplicate Alarms
DUPLICATE ALARMS
NO YES This option displays for BACKUP paths. If Yes is selected, the current backup path
duplicates all alarms occurring on its group primary path. Default is NO.

Alarm Reports
ALARM YES This option displays when the Path Type is Primary. All backup paths within the group
follow the same programming for Alarm Reports. Default is YES.
When YES is selected, the following reports are sent to the receiver for all zone types:

• Alarm • Bypass • Reset • Restore

When FIRE is selected, the following reports are sent for Fire, Fire Verify and Supervisory
NO YES FIRE
Zones:

• Alarm • Bypass • Reset • Restore

Supervisory/Trouble Reports
SPV/TRBL YES This option displays when the Path Type is Primary. All backup paths within the group
follow the same programming for Supervisory/Trouble Reports. Default is YES.

When YES is selected, the following reports are sent for all zone types:
NO YES FIRE • Trouble • Low Battery • Missing • Fault

• Restorals • System Troubles • System Restoral

When FIRE is selected, the following reports are sent for Fire, Fire Verify, and Supervisory
Zones:
• Trouble • Low Battery • Missing • Fault

• Restorals • System Troubles • System Restoral

Serviceman reports are sent regardless of the selection made for Supervisory/Trouble
reports.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

9
 Opening/Closing and User Reports
O/C USER NO YES This option displays when the Path Type is Primary. All backup paths within the group
follow the same programming for Opening/Closing and User Reports. Default is YES.

When YES is selected, the following reports by user are sent to this receiver.
• Opening • Code changes (including adding, deleting, changing)

• Closing • Schedule changes (temporary, permanent, shift)

• Bypass • Holiday date changes

• Reset

Door Access Report

DOOR ACS DENY This option displays when the Path Type is Primary. All backup paths within the group
follow the same programming for Door Access Reports. Default is DENY.
Select YES to enable Door Access Granted and Denied reports to this receiver whenever
NO YES DENY a door access is granted to a user. The Door Access Granted report is only sent if the
keypad number has also been selected in Access Keypads under the SYSTEM REPORTS
programming.
Select DENY to enable Door Access Denied reports only to this receiver when a door
access is denied to a user.

Panic Test (Network Only)

PANIC TST NO YES YES allows the panic zone test verication and failure results to be sent to the central
station receiver. NO disables the panic test report. The default setting is NO. The system
test start, stop, panic zone verication, and panic zone failure messages sent to the central
station and the trips count operation are the same as used under the Walk Test. See Using
the Walk Test section in the Appendix.

SEND COMM TRBL: Send Communication Trouble

NO YES This option displays for each path and determines if and how communication trouble on
the path is sent to the receiver. A trouble message indicates both the path number and
communication type that failed. Default is YES.

SEND PATH INFO: Send Path Information

NO YES This option displays for each path and if YES, each panel message includes path
information such as path number, communication type, and path type. Default is NO.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

10
NETWORK OPTIONS
Network Options are provided to dene the network conguration for the panel. This information will be used during
communication of messages via network. A 763 Wi-Fi Module is required in order to send alarm signal communication.
IP addresses and port numbers may need to be assigned by the network administrator. When entering an IP, Gateway, or
Subnet Mask address be sure to enter all 12 digits and leave out the periods.

WPS LIST MANUAL Wi-Fi Setup

TEST This option is for connecting to the desired Wi-Fi network and will display only when
Comm Type is set to Wi-Fi. Press any select key or area to select.
WPS - Automatically connects to a WPS enabled router.
WPS LIST MANUAL
TEST LIST - Displays the names and signal strength of any Wi-Fi routers in range.
MANUAL - Enter the name of the Wi-Fi router you wish to connect to.
TEST - Veries connection of your system to the Wi-Fi network.

WPS
SEARCHING When WPS is selected, SEARCHING displays. Press the WPS button on the Wi-Fi network
router to which you are attempting to connect. SEARCHING displays for up to two minutes
or until connected to the WPS enabled router. Refer to the router’s instruction manual for
sending a security key to the XR150INT/XR550INT Series panel.
If the panel fails to connect to the WPS enabled router, WPS FAILED RETRY? NO YES
displays. Press the fourth select key or area to RETRY or press the third select key or area
to display WPS LIST MANUAL.

WPS LIST MANUAL List

SEARCHING When LIST is selected, SEARCHING displays until any Wi-Fi networks are found in range.
Once available Wi-Fi networks are found the keypad displays the name of the SSID (Wi-Fi
SIGNAL XXXXXX Network name) and signal strength of each network. Press CMD to scroll through the list
HOMENET123 of available Wi-Fi networks. When the desired network is displayed, press any select key or
area to connect.

Manual
WPS LIST MANUAL This option allows you to enter the desired network name using the keypad. When
MANUAL is selected, the current settings display. Press CMD to continue with no change.
WIFI SETUP SecureCom is the default.
ENTER SSID Once the SSID is entered, press CMD and SEARCHING displays.
When an SSID is entered for the rst time or changed, the panel searches for the SSID
entered to ensure communication. The keypad displays SSID FOUND or SSID NOT FOUND.
SSID When the SSID is found, the security type is also detected.
SSID FOUND Enter up to 32 characters for the SSID from the network router to identify the network LAN.
The SSID is blank by default. Use the chart below to enter lowercase or special characters.
Each successive press of the select key or area gives additional options.

Key Number Select Key Select Key Select Key Select Key
or area 1 or area 2 or area 3 or area 4
1 A, a, B, b C, c (, [, {
2 D, d E, e F, f ), ], }
3 G, g H, h I, i !, ^, ~
4 J, j K, k L, l ?, ", |
5 M, m N, n O, o /, \, `
6 P, p Q, q R, r &, $
7 S, s T, t U, u @, %
8 V, v W, w X, x ,=
9 Y, y Z, z space, : _, ;
0 -, + ., ' *, < #, >

SSID If the 763 is unable to connect to the desired network and SSID NOT FOUND displays,
SSID NOT FOUND press CMD to return to the main menu and WPS LIST MANUAL displays. Press CMD again
to display TEST.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

11
 Test
TEST Press the rst select key or area to select TEST and the 763 Wi-Fi module will attempt to
verify connection of your system to the selected Wi-Fi network.

W/L SECURITY Wireless Security Type

WPA-PSK When successful, W/L SECURITY displays. Select the security type based on the network
router programming. The default network security type is WPA-PSK. Press any select key
or area to display the other security options. The available options are WEP, WPA, and
NONE.
W/L SECURITY Press the rst select key or area to choose WEP, press the second select key or area for
WEP WPA NONE WPA, press the third select key or area for NONE.

W/L KEY Wireless Network Key

***************** This option displays only if Comm Type is set to Wi-Fi and Security option is not set to
NONE. Enter the key provided from the network router’s programming. WEP requires
a network password of 10 characters (WEP64) or 26 characters (WEP128), using a
combination of the number 0-9 and the letters A-F (See the chart above to enter
lowercase or special characters).
WPA/WPA-PSK uses a custom key that allows 8 to 32 characters.
When connecting to the Wi-Fi network the panel also detects the security type in use and
W/L KEY: *************** displays.
Enter the W/L KEY and the panel performs a connection test and CONNECTING displays.
When successful, CONNECTED displays on the keypad. If the panel does not connect to
the Wi-Fi network, NOT CONNECTED displays. Press CMD to return to the Wi-Fi SETUP
main screen.
Depending on the security type, the key might take several seconds to process.

USE IPV6: IPV6

NO YES At the IPV6 prompt, select YES to use an IPV6 address. The default is NO. IPV6 is DHCP
only.

DHCP
DHCP NO YES If the panel uses a dynamic IP address select YES. When set to YES, the panel operates
using DHCP and does not use the Local IP Address number. When the DHCP option is set
to NO, the panel uses the IP address entered in Local IP Address. The default value for
DHCP mode is YES.

LOCAL IP ADDRESS Local IP Address

192 .168.0.250 Enter the local IP address for the panel. The Local IP Address must be unique and cannot
be duplicated. The default local IP address is 192.168.0.250.

GATEWAY ADDRESS Gateway Address

192 .168.0.1 Enter the local gateway address. The Gateway IP Address is needed to exit your local
network. The default gateway address is 192.168.0.1.

SUBNET MASK Subnet Mask

255.255.255.000 Enter the local subnet mask assigned to the panel. The default subnet mask address is
255.255.255.000.

DNS SERVER DNS Server

192.168.0.1 Enter the IP address of the DNS (Domain Name System) used by the panel to resolve
domain names into IP addresses. The default address is 192.168.0.1.
On systems with hardwired network connection, the DNS address can be changed even if
the panel has DHCP enabled.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

12
PASSPHRASE Passphrase (XR550INT with Encryption Only)
- To enable encryption, type an 8 to 16-character Passphrase using alphanumeric characters.
If you leave the Passphrase blank, the panel communicates with the SCS-1R or SCS-VR
Receiver, but the data is not encrypted. The Passphrase is blank by default.
An XR550INT panel with encryption is capable of communicating 128-bit or 256-bit
encrypted data to an SCS-104 line card installed at the receiver. The XR550INT panel with
encryption and the receiver SCS-104 line card must have the same password called a
Passphrase.
An XR550INT panel with encryption communicates using AES encryption. If you currently
have an XR550INT panel with network installed, you may purchase a separate feature key
to activate encrypted communications using the Feature Upgrade process described in
the Feature Upgrade Section. Encrypted communication cannot be enabled on a standard
XR550INT panel. 256-bit encrypted messages to the SCS-1R receiver only communicate
when using SCS-104 Receiver Line Cards with Version 102 or higher software.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

13
DEVICE SETUP
Device Setup
DEVICE SETUP This section allows you to dene the panels physical conguration. You can install and
address up to sixteen supervised devices on the keypad bus. Devices can also be added to
available LX-Busses. Programmable devices are Keypad, Door, Fire, and Expander.

CARD OPTIONS Custom Card Denitions

DMP CUSTOM ANY Select the slot number (1-8) that you would like to program a custom non-DMP card
format into. The format that is programmed into slot 1 is the default format. In the event
that a card with an unrecognized format is used, that card will be read in the format that is
programmed in slot 1. To restrict card reads to specic formats, only program slots 2-8. For
a chart of commonly used card formats and their defaults, refer to the 734INT Installation
Guide (LT-0737INT).
Select DMP to allow credentials that use a 26 - 45 bit data string.
Select CUSTOM to disable DMP format and program slots 1-8 as needed.
Select ANY to allow all card reads to activate the door strike relay. No user code
information is sent to the panel.
If you select slot 1 and are updating an XR International Series panel with rmware Version
182 or earlier, Format Name will automatically be named Single Card Format and Wiegand
Code Length will default to 45.

WIEGAND CODE Wiegand Code Length

LENGTH: 26 When using a custom credential, enter the total number of bits to be received in Wiegand
code including parity bits. Press any select key or area to enter a number between 1-255 to
equal the number of bits. Default is 26 bits.
The starting position location and code length must be determined and programmed into
the 734INT Module.

SITE CODE Site Code Position

POSITION: 1
Enter the site code start position in the data string. Press any select key or area to enter a
number between 0-255. Default is 1.

SITE CODE Site Code Length

LENGTH: 8 Enter the number of characters the site code contains. Press any select key or area to enter
a number between 1-16. Default is 8.

USER CODE User Code Position

POSITION: 9 Dene the User Code start bit position. Press any select key or area to enter a number
between 0-255. Default is 9.

USER CODE User Code Length

LENGTH: 16 Dene the number of User Code bits. Press any select key or area to enter a custom
number. On a 734INT module, custom numbers can only be between 16-40. The default is
16.

REQUIRE SITE Require Site Code

CODE: NO YES Press the select key or area under YES to use a site code.
In addition to User Code verication, door access is only granted when any one site code
programmed at the SITE CODE ENTRY option matches the site code received in the
Wiegand string.

Site Code Display

SITE CODE 1: - 734INT Module: You can program up to 8 eight-digit site codes. Site code range is
0-16,777,214. Any previously programmed site codes display. Dashes represent blank site
codes. Default is blank.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

14
NO. OF USER CODE Number of User Code Digits
DIGITS 5 The 734INT module recognizes user codes from 4-12 digits in length. Press any select key
or area to enter a user code digit length. This number must match the user code number
length being used by the panel. Default is 5. For an Area System, use 4 to 12 digits. For all
other XR International Series panel congurations, use 4 digits.
Any selection above 5 digits require entry of the custom card denitions with custom site
and user code positions for the Wiegand string. When searching the bit string for the user
code, the digits are identied and read from left to right.

Device Number
DEVICE NO: - Enter the address of the device you are programming. After you program each option for
the rst device, repeat these programming steps for each additional device. Programmable
devices are KEYPAD, DOOR, FIRE, and EXPANDER. The available addresses are 1 - 16 on
the panel keypad bus, and 500 - 999 on the LX-Bus. The valid range for KEYPAD, FIRE, and
EXPANDER type devices is 1 - 16 on the panel keypad bus. The valid range for DOOR type
devices is 1 - 16 on the panel keypad bus and 501 - 961 on the AX-Bus.
See the AX Bus Addresses and 734INT Zone Numbers chart on the next page. Wireless
keypads and network door controllers are not able to occupy address 1.
AX-Bus Operation for 734INT Access Control Modules
Once a 734INT address has been programmed for the bus, the LX-Bus is automatically
converted from a hardwire zone expansion bus to a hardwire Access Expansion Bus
(AX-Bus) and the bus begins to operate as shown below.
• Each 734INT module provides one door relay and four protection zones to connect
switches such as door and window contacts.
• 16 doors of access can be programmed per AX-Bus to a maximum of eighty (80)
734INT modules. Please see the table below for available addresses.
• Any unused AX-Bus zone numbers may be programmed as wireless zones. Hardwired
zone expansion modules such as the 711, 714, 715-16 and others are incompatible with
bus operation and cannot be used.
• Device Setup programming for AX-Bus address are automatically programmed as a
door type. Device Type, Communication Type and Display Areas are not shown. Only
734INT module programming is shown.
An AX-Bus operation is compatible with 734INT modules and XR550INT Series control
panels. AX-Bus operation is incompatible with XR150INT Series control panels.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

15
Device Addresses and 734INT Zone Numbers

Keypad Bus LX/AX Bus

Device/ Device/ Device/ Device/ Device/ Device/
Zones Zones Zones Zones Zones Zones
Door Door Door Door Door Door
1 11-14 501 501-504 601 601-604 701 701-704 801 801-804 901 901-904
2 21-24 505 505-508 605 605-608 705 705-708 805 805-808 905 905-908
3 31-34 509 509-512 609 609-612 709 709-712 809 809-812 909 909-512
4 41-44 513 513-516 613 613-616 713 713-716 813 813-816 913 913-916
5 51-54 517 517-520 617 617-620 717 717-720 817 817-820 917 917-920
6 61-64 521 521-524 621 621-624 721 721-724 821 821-824 921 921-924
7 71-74 525 525-528 625 625-628 725 725-728 825 825-828 925 925-928
8 81-84 529 529-532 629 629-632 729 729-732 829 829-832 929 929-932
9 91-94 533 533-536 633 633-636 733 733-736 833 833-836 933 933-936
10 101-104 537 537-540 637 637-640 737 737-740 837 837-840 937 937-940
11 111-114 541 541-544 641 641-644 741 741-744 841 841-844 941 941-944
12 121-124 545 545-548 645 645-648 745 745-748 845 845-848 945 945-948
13 131-134 549 549-552 649 649-652 749 749-752 849 849-852 949 949-952
14 141-144 553 553-556 653 653-656 753 753-756 853 853-856 953 953-956
15 151-154 557 557-560 657 657-660 757 757-760 857 857-860 957 957-960
16 161-164 561 561-564 661 661-664 761 761-764 861 861-864 961 961-964

Device Name
* UNUSED * A device name must be given to each device in the system. To add a device name, press
any select key or area. The default device name (DEVICE X) displays. Select CMD to
accept the default name or press any select key or area to enter a new name up to 32
alphanumeric characters. Press CMD.
To remove a device from the system, delete the device name by pressing any select key or
area, then press CMD. The panel automatically programs the name as * UNUSED *.

TYPE: KEYPAD Device Type

DOOR KPD FI EXP This section allows you to select a device type for the selected device number.

DOOR - The device is an access control device and is either a keypad using door strike
functions or a Wiegand Interface Module. Devices with an address higher than 16 are
VPX
automatically assigned as a DOOR device type.

KEYPAD - The device type is a non-re, non-access keypad.

FIRE - The device type is a re device.

EXPANDER - A Zone Expansion Module.

Private Door
PRIVATE DR NO YES Select YES to assign this address as a private door, which will not be assigned to an access
area. The private door can then be added to a prole. Up to four private doors can be
assigned to an individual prole.
Select NO to not allow a door to be designated as a private door. Default is NO.

DEVICE COMM TYPE Device Communication Type

KPD-BUS AX-BUS KEYPAD - Select KPD for devices that are connected to the keypad bus. Select AX-BUS for
addresses 501-964.

DEVICE COMM TYPE DOOR - For wired devices, select KPD BUS for addresses 1-16 or select AX BUS for
NETWORK WLS addresses 501-964. For network devices, select NETWORK.

Serial Number
SERIAL #:XXXXXXXX This option only displays if Device Type is KEYPAD and Device Comm Type is WIRELESS.
Enter the eight-digit serial number found on the wireless keypad.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

16
 Supervision Time
SUPERVSN TIME: 240 This option only displays if Device Type is KEYPAD and Device Comm Type is WIRELESS.
Press any select key or area to select the supervision time required for the device. Press
SELECT MINUTES:
CMD to accept the default time. Default is 240 minutes.
0 60 240
Press the select key or area under the required number of minutes. The device must check
in at least once during this time or a missing condition is indicated for that device. Zero (0)
indicates an unsupervised wireless keypad.

Access Areas
ACCESS AREAS Press CMD to program Access Areas. To select an area, enter the area number using the
digit keys on the keypad. When an area is selected, an asterisk appears next to the area
number. Enter the number again to deselect the area. Press CMD to display the next set of
areas.
Users must have matching access area numbers assigned to their code to receive a door
access at this device.
For an All/Perimeter, Home/Sleep/Away, or Home/Sleep/Away with Guest system, Access
Areas should be left at factory default settings.

Egress Areas
EGRESS AREAS Press CMD to program Egress Areas. To select an area, enter the area number using the
digit keys on the keypad. When an area is selected, an asterisk appears next to the area
number. Enter the number again to deselect the area. Press CMD to display the next set of
areas.
Use this option to detect Anti-passback violations. Anti-passback requires a user to
properly exit (egress) an area they have previously accessed. If users fail to exit through the
proper card reader location they are not granted access on their next attempt.

Display Areas
DISPLAY AREAS Press CMD to program Display Areas. To select an area, enter the area number using the
keypad digit keys. When an area is selected, an asterisk appears next to the area number.
Enter the number again to deselect the area. Press CMD to display the next set of areas.
Default is all area numbers.
Display Areas allows the panels burglary activities to be segmented so that only specic
area(s) and their associated operation appear at a particular keypad. Area number(s)
selected in this eld aect the way users interact with the system from this particular
device. This allows specic area control from specic keypads, as well as annunciation of
zones assigned to those area(s).

When Display Areas is left defaulted (all areas selected), Menu Display and Status List
items determine whether zone alarms and troubles display at this device, regardless of area
assignment. Also, all system areas may be armed and disarmed from this device.
For an All/Perimeter or Home/Sleep/Away system, Display Areas should be left at factory
default settings.

For Home/Sleep/Away with Guest arming systems, the Display Areas selection determines
which system the keypad arms and disarms. With areas 1, 2 or 3 being the rst areas
selected, the keypad is assigned to the Main system. With area 4, 5 or 6 being the rst
areas selected, the keypad is assigned to the Guest 1 system. With area 7, 8 or 9 being the
rst areas selected, the keypad is assigned to the Guest 2 system (Guest 2 only applies to
XR550INT systems). Keypads can have additional areas assigned for Event Display.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

17
 User Action Allowed
When an area(s) is selected, the following user actions are allowed:

• Arming or Disarming of the area(s) selected from the ARM or DISARM menu

• Alarm Silence for the area(s) selected

• Zone Bypass of zones assigned to the area(s) selected

• Zone Monitor of zone assigned to the area(s) selected

• Shift schedule changes allowed for the area(s) selected

• Closing Check Schedule Extend is allowed for the area(s) selected

• Door Schedules changes are allowed for devices that have a matching area(s)
as dened in Device Access Areas

• Door On/O Menu operation is allowed for devices that have a matching area(s)
as dened in Device Access Areas

The user actions also require the matching area(s) be programmed in User Prole: Arm/
Disarm area(s).

Status Display Allowed

When an area(s) is chosen, the following displays are allowed:

• Armed Status of the selected area(s)

• Zone Alarms and troubles for burglary (NT, DY, EX, A1, A2) type zones assigned to the
selected area(s)

• Late to Close status of the selected area(s)

• Zone Status (normal/fault) of zones that are assigned to the selected area(s)

Options and Actions Not Aected

The following options are not aected by the Display Areas operation. The User Code
authority level controls access to these items.

• Sensor Reset Menu • Outputs On/O Menu • System Status Menu

• System Test/Panic Test • User Proles • Forgive Anti-Passback

• Service Request • Set System Time and Date • Fire Drill

• Display Events

• 24-hour zones display at keypads based on Status List programming only

Strike Time
STRIKE TIME: 5 Enter a door access time, between 1 and 250 seconds, during which a keypad or access
control device relay is activated. Magnetic locks or electric door strikes are connected to
the relay and released for the length of the strike time. Default is 5 seconds.
Enter 0 (zero) to activate the device relay with a toggle action. This allows the user to
activate or deactivate the device relay each time a valid user code is entered. The device
relay is activated or deactivated until a user code is entered again.

Strike Delay
STRIKE DELAY: 0 Enter the number of minutes, 0 to 9, to delay a door strike after a valid code is entered
or a card read occurs. When a valid code or card read is received, the activation of the
door strike is delayed for the number of minutes programmed. The standard door strike
message is sent to the Central Station receiver. During this delay, all subsequent codes
entered or cards presented to the reader for a door strike are ignored and no record of the
attempt is stored. Enter 0 (zero) to disable. Default is 0 (zero).

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

18
 Fire Exit Release
FIRE EXIT NO YES Select YES to allow the door access relay at this address to be released whenever Fire panic
keys are pressed or a Fire or Fire Verify zone alarm is in the Status List. The relay is reset
whenever a Sensor Reset is performed to remove all Fire and Fire Verify zone alarms from the
Status List. Select NO to not allow the door access relay at this address to be released.

Public Door
PUBLIC DR NO YES Select YES to allow the door access relay at this address to be locked whenever the
Lockdown command is issued from the keypad User Menu or remote command.
Select NO to not allow the door access relay at this address to be released. Default is NO.

Output Group
OUT GROUP NO YES Select YES to allow the output group (relays) assigned to the user prole to turn ON when
the device relay is activated for the programmed strike time. Default is NO. See the User
Proles section in the Appendix of this document for more information about proles.

Schedule Override
OVERRIDE NO YES Use this option to allow door ON/OFF schedules to be overridden by the armed condition
of the system. Selecting YES causes the on time for a door schedule to be ignored when
all areas assigned to Access Areas for this device are armed. Should any area become
disarmed after the door schedule on time, the device output turns on. A door output which
is on during a disarmed period automatically turns o when all access areas assigned
to the device become armed, even if the scheduled o time has not been reached. This
feature can be used to keep doors locked when a factory opens late, or is forced to close
early, due to a snow storm or other cause.
Select NO to allow door schedules to operate independent of system armed status.
When OVERRIDE is YES and there are no areas programmed in ACCESS AREAS, the
door schedule for that device does not work. Either set OVERRIDE to NO or enter an area
number in ACCESS AREAS.

AUTO FORCE ARM Auto Force Arm Device?

DEVICE? NO YES Select YES to have all Display Areas assigned to this keypad automatically arm and force
arm faulted zones at arming. The user is not prompted to select areas to arm or force arm
faulted zones after choosing ARM at the keypad. If Closing Code is programmed as YES,
only the matching areas between the Display Areas and the User Code’s authorized areas
arm. Also, when YES is selected, the user is not prompted to select areas to disarm after
entering a code at Entry Delay or after choosing Disarm at the keypad. All matching areas
assigned to the User Code and to this keypad are automatically disarmed. When NO is
selected, the user is prompted to select areas (ALL NO YES) and choose to force arm or
bypass at arming and disarming. Default is NO.

DOOR REAL-TIME Door Real-Time Status?

STATUS? NO YES Select YES to have real-time door status messages sent to the PC Log, Entré, and Dealer
Admin accounts that are reporting for this device. Messages are sent anytime the panel
turns the door relay on or o. Default is NO.

PIN DISARM? PIN Disarm?

NO YES Select NO to not allow PIN entry to disarm the system under any circumstance. Instead,
access credentials, wireless key fobs, and remote disarm can be used to disarm the system.
Select YES to allow PIN entry to disarm the system. Default is YES.

SEND DOOR FORCED Send Door Forced Message?

MESSAGE? NO YES Select YES to have the panel send a real-time door status message of Forced Open (FO)
to PC Log reporting and Entré reporting when the door relay is o, but the door zone has
transitioned from its normal state. Default is NO.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

19
PROGRAM 734 Program 734INT Options
OPTIONS? NO YES Select YES to program a 734INT Module. To program the 734INT, the Device Type must be
set to DOOR and the Device Communication Type must be set to KPD-BUS or AX-BUS.

ACTIVATE ZONE 2 Activate Zone 2 Bypass

BYPASS? NO YES Select YES to activate the Bypass option.
Selecting NO allows standard zone operation on Zone 2 and displays the ACTIVATE ZONE
3 REX option. Default setting is NO.
If the door being released by the 734INT module is protected (contact installed), you can
provide a programmable Bypass entry/exit timer by connecting its contact wiring to the
734INTmodule Zone 2. When the on-board Form C relay activates and the user opens the
door connected to Zone 2, the zone is bypassed for the number of seconds programmed in
ZONE 2 BYPASS TIME allowing the user to enter/exit.
If Zone 2 does not restore (door closed) within the programmed bypass time, the 734INT
piezo pulses during the last ten seconds. If Zone 2 restores prior to the end of the
programmed time, the piezo silences. If the zone does not restore before the programmed
time, the 734INT ends the bypass and indicates the open or short zone condition to the
panel.

ZONE 2 BYPASS Zone 2 Bypass Time

TIME: 40 Enter the number of Bypass seconds to elapse before the Bypass timer expires. Range is
from 20 to 250 seconds. Press any select key or area to enter the number of seconds. If the
door remains open when the timer expires a zone open/short is sent to the panel for Zone
2. The default is 40 seconds.

RELOCK ON ZONE 2 Relock on Zone 2 Change?

CHANGE? NO YES Select NO to leave the relay on for the door access time when Zone 2 restores.
Select YES to turn the 734INT relay o and relocks the door when Zone 2 changes state.
The default is NO.

ACTIVATE ZONE 3 Activate Zone 3 Request to Exit

REX? NO YES Selecting YES activates the Zone 3 Request to Exit (REX) option.
Selecting NO allows standard zone operation on Zone 3 and displays the ACTIVATE
ONBOARD SPEAKER option. Default setting is NO.
Optionally connect a PIR (or other motion sensing device) or a mechanical switch to Zone
3 to provide REX capability to the system. When Zone 3 shorts, the on-board Form C relay
activates for the programmed number of seconds. During this time, the user can open the
protected door to start the programmed Bypass entry/exit timer. After the programmed
number of seconds, the relay restores the door to its locked state.
The 734INT module provides a bypass-only option for REX on Zone 3. When Zone 3
opens from a normal state, only a bypass occurs: the on-board relay does not activate.
This bypass-only option uses two methods of REX. The rst REX device provides the
programmed Bypass entry/exit timer. The second REX device, or manual device such as a
door knob, unlocks the door.
An example of the bypass-only conguration is a door to an oce that is locked 24 hours
a day. Users pass a REX motion detector positioned by the door to begin the programmed
exit timer. Within the programmed number of seconds the user must then manually activate
a second device, such as a REX device or manual door knob, to unlock the door. If the door
is opened after the programmed number of seconds, the zone goes into alarm.

ZN 3 REX STRIKE Zone 3 REX Strike Time

TIME: 5 Enter the number of REX seconds to elapse. Range is from 5 to 250 seconds. Press any
select key or area to enter the number of seconds. The default is 5 seconds.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

20
REMOTE OPTIONS
Remote Options
REMOTE OPTIONS This section allows you to enter the information needed for Remote Command/Remote
Programming operation.

Remote Key
REMOTE KEY This option allows you to enter a code of up to 16 characters. Remote Link™ and Dealer
Admin must give the correct key to the panel before being allowed any remote functions.
All panels are shipped from the factory with the key preset as blank. This can be an optional
or required option
To enter a remote key or change the current one, press a select key or area and enter any
combination of up to 16 digits. Press CMD. The current key displays as asterisks.

REMOTE DISARM? Remote Disarm

NO YES YES allows the panel to be disarmed remotely. NO disables remote disarming. Default is
YES.

ARMED ANSWER Armed Answer Rings

RINGS: 8 Enter the number of rings the panel counts before answering the phone line when all
system areas are armed. Any number from 0 to 15 can be entered. If 0 (zero) is entered, the
panel does not answer the phone when all system areas are armed. The default is 8.

DISARMED ANSWER Disarmed Answer Rings

RINGS: 8 Enter the number of rings the panel counts before answering the phone line while any
system areas are disarmed. Any number from 0 to 15 can be entered. If 0 (zero) is entered,
the panel does not answer the phone when any system area is disarmed. The default
number is 8 (eight).

PC Modem
PC MODEM NO YES YES allows the panel to answer the telco link and connect with Remote Link™ through the
PC Modem at 2400 baud. NO disables PC Modem communication.

Alarm Receiver Authorization

ALR RCVR NO YES Select YES to enable remote commands and programming to be accepted from the alarm
SCS-1R Receiver. The Remote Key option can also be required.
With YES selected, the panel requests the receiver key during its rst communication with
the rst SCS-1R Receiver. The panel retains this alarm receiver key in memory and allows
remote commands to be accepted from the alarm receiver. If an alarm occurs during a
remote connect, the alarm report is immediately sent to this receiver only.
When NO is selected, remote commands and programming are not accepted from the
alarm SCS-1R Receiver.

Service Receiver Authorization

SVC RCVR NO YES YES enables remote commands and programming to be accepted from a secondary
service receiver other than the alarm SCS-1R Receiver. The Remote Key option can also be
required.
With YES selected, the panel requests the service receiver key the rst time it is contacted
by the service receiver. The panel retains this service receiver key in memory and accepts
remote commands from the service receiver.
If an alarm occurs during a remote connect, the panel disconnects from the service
receiver and calls the alarm receiver. Alarm reports are only sent to the alarm receiver.
It is important that the alarm receiver key and the service receiver key programmed at
the central station are NOT the same so the panel can determine the dierence between
receivers.
When NO is selected remote commands and programming are not accepted from a
secondary service receiver.
XR150INT/XR550INT Series Programming Guide Digital Monitoring Products
21
MANUFACTURER Manufacturer Authorization
AUTH? NO YES Select YES to allow DMP Technical Support technicians to access the panel during system
service or troubleshooting. This authorization automatically expires within one hour.

DMP remote service is provided on a read only basis: DMP technicians can look at the
system programming and make suggestions only. Alterations can only be accomplished by
installing company service personnel.

ALLOW NETWORK Allow Network Remote

REMOTE? NO YES This option displays only if the panel has network capability. YES allows remote
programming over the network. Changing this option does not change any other network
programming options. Default is YES.

NETWORK PROG
Network Programming Port
PORT: 2001 Enter the programming port number. The programming port identies the port used to
communicate messages to the panel. The default Programming Port setting is 2001.

ENCRYPT NETWORK Encrypt Network Remote

REMOTE? NO YES YES encrypts data sent over network. Default is NO.

ALLOW CELL Allow Cellular Remote

REMOTE? NO YES YES allows remote programming using cellular connection. Default is YES.

FIRST GPRS APN: APN

SECURECOM400 Enter the rst APN (Access Point Name). This allows an access point for cellular
communication and is used to connect to a DNS network. The APN may contain two lines
of 16 characters to equal 32 characters. Default is set to SECURECOM400.

ENCRYPT CELL Encrypt Cellular Remote

REMOTE? NO YES YES encrypts data sent over a cellular connection. Default is NO.

Entré Connection
ENTRE
CONNECTION: NONE This option displays if the panel has network or cellular capability. Select NET to allow a
dedicated network connection with Entré. Options are NONE, NET, or CELL. Default is
NONE.

ENTRE INCOMING Entré Incoming TCP Port

TCP PORT: 2011 This option displays only if NET is chosen for the Entré connection. Enter the programming
port number for the incoming Entré connection. The programming port identies the port
used to communicate messages to and from the Entré software. This port cannot be the
same port as programmed in Network Programming Port. The default Programming Port
setting is .

Entré IP Address
ENTRE IP This option displays only if NET is chosen for the Entré connection. Enter the Entré IP
address where the panel sends network messages. The Entré IP Address must be unique
and cannot be duplicated on the network. Enter all 12 digits and leave out the periods.
For example, enter IP address 192.168.0.250 as 192168000250. The periods display
automatically. Default is 0.0.0.0.

ENTRE OUTBOUND Entré Outbound TCP Port

TCP PORT: 2001 This option displays only if NET is chosen for the Entré connection. Enter the programming
port number for the outbound Entré connection. The programming port identies the port
used to communicate messages to the Entré software. Default is 2001.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

22
ENTRE BACKUP Entré Backup Connection
NONE NET CEL This option displays if NET or CEL is chosen for the Entré connection. Enter the backup
address where the panel sends network messages if the rst Entré connection fails. The
Entré connection must be unique and cannot be duplicated on the network. If the backup
connection is NET, enter all 12 digits and leave out the periods. The periods display
automatically. Default is 0.0.0.0.

ENTRE BACKUP TCP Entré Backup TCP Port

PORT: 2001 This option displays only if NET or CELL is chosen for the Entré connection. Enter the
backup programming port number for the outbound Entré connection in case the
connection to the primary IP fails. Default is 2001.

ENTRE REPORTS Entré Reports

000.000.000.000 This option displays only if NET is chosen for the Entré connection. Choose which types of
system reports are sent to Entré. Press CMD to view all of the Entré report options. Choose
YES to enable arming/disarming, zone, user code, door access, or supervisory message
reports. All Entré reports default to YES.

Arm and Disarm Reports

ARM/DIS NO YES Sends arming, disarming and Late to Close events. Includes the area number, name and
action, the user number and name, and the time and date.

Zone Reports
ZONE: NO YES Sends changes in the status of active zones. Includes the zone number, name, type,
the action (alarm, trouble, bypass, etc.), user number (if applicable), and area name. If
performing a Walk Test, Zone Verify and Zone Fail messages are sent for each zone.

User Command Reports

USER CMDS NO YES Sends user code changes, schedule changes, and door access denied events.

Door Access Reports

DOOR ACS: NO YES Sends door access activity: door number, user number and name, and time and date.

Supervisory Reports
SUPV MSG: NO YES Sends system monitor reports, such as AC and battery, and system event reports.
Supervisory Reports also sends the following reports:
• Abort • Exit Error • Ambush
• System Recently Armed • Alarm Bell Silenced • Unauthorized Entry
• Late to Close*
* Only sent as a Supervisory Report if Area Schedules is not enabled, Closing Check is
enabled, and an opening/closing schedule has been programmed.
To send these reports to the PC Log, you must enable SUPV MSG.

Video Reports
VIDEO: NO YES Enabling this feature will allow the panel to send video system reports to Entré when an
OpenEye® event message has been received from a camera.

ENTRE CHECKIN Entré Checkin

MINUTES: 0 Select the rate at which check-in messages are sent over the Entré connection. Select 0
(zero) to disable check in messages. Range is 0, 3-240 minutes. Default is 0.

ENTRE PASSPHRASE Entré Passphrase

- To enable encryption enter an 8 to 16-character Passphrase using alphanumeric characters.
If you leave the Passphrase blank, the panel communicates with Entré, but the data is not
encrypted. The Passphrase is BLANK by default.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

23
INTEGRATOR Integrator Connection
CONNECTION: NONE This option displays if the panel has network or cellular capability. Select NET to allow
a dedicated network connection with the integrator. Options are NONE, NET, or CELL.
Default is NONE.

INTGRTR INCOMING Integrator Incoming TCP Port

TCP PORT: 8011 This option displays only if NET is chosen for the integrator connection. Enter the
programming port number for the incoming connection. The programming port identies
the port used to communicate messages to and from the integrator software. This port
cannot be the same port as programmed in Network Programming Port. The default
Programming Port setting is 8011.

INTEGRATOR IP Integrator IP Address

000.000.000.000 This option displays only if NET is chosen for the integrator connection. Enter the
integrator IP address where the panel sends network messages. The integrator IP
Address must be unique and cannot be duplicated on the network. The periods display
automatically. Default is 0.0.0.0.

INTGRTR OUTBOUND Integrator Outbound TCP Port

TCP PORT: 8001 This option displays only if NET is chosen for the integrator connection. Enter the
programming port number for the outbound connection. The programming port identies
the port used to communicate messages to the integrator software. Default is 8001.

INTGRTR BACKUP IP Integrator Backup Connection

NONE NET CELL This option displays if NET or CELL is chosen for the integrator connection. Enter the
backup address where the panel sends network messages if the rst integrator connection
fails. The connection must be unique and cannot be duplicated on the network. If the
backup connection is NET, enter all 12 digits and leave out the periods. For example, enter
IP address 192.168.0.250 as 192168000250. The periods display automatically. Default is
0.0.0.0.

INTGRTR BKUP TCP

Integrator Backup TCP Port
PORT: 8001 This option displays only if NET is chosen for the integrator connection. Enter the backup
programming port number for the outbound connection in case the connection to the
primary IP fails. Default is 8001.

Integrator Reports
INTGRTR REPORTS This option displays only if NET is chosen for the integrator connection. Choose which
types of system reports are sent to the integrator. Press CMD to view all of the integrator
report options. Choose YES to enable arming/disarming, zone, user code, door access, or
supervisory message reports. All reports default to YES.

Arm and Disarm Reports

ARM/DIS: NO YES Sends arming, disarming and Late to Close events. Includes the area number, name and
action, the user number and name, and the time and date.

Zone Reports
ZONE: NO YES Sends changes in the status of active zones. Includes the zone number, name, type,
the action (alarm, trouble, bypass, etc.), user number (if applicable), and area name. If
performing a Walk Test, Zone Verify and Zone Fail messages are sent for each zone.

User Command Reports

USR CMDS: NO YES Sends user code changes, schedule changes, and door access denied events.

Door Access Reports

DOOR ACS: NO YES Sends door access activity: door number, user number and name, and time and date.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

24
 Supervisory Reports
SUPV MSG: NO YES Sends system monitor reports, such as AC and battery, and system event reports.
Supervisory Reports also sends the following reports:
• Abort • Exit Error • Ambush
• System Recently Armed • Alarm Bell Silenced • Unauthorized Entry
• Late to Close*
* Only sent as a Supervisory Report if Area Schedules is not enabled, Closing Check is
enabled, and an opening/closing schedule has been programmed.
To send these reports to the PC Log, you must enable SUPV MSG.

INTGRTR PASSPHRASE Integrator Passphrase

- To enable encryption enter an 8 to 16-character Passphrase using alphanumeric characters.
If you leave the Passphrase blank, the panel communicates with the integrator, but the data
is not encrypted. The Passphrase is blank by default.

SEND LOCAL Send Local Changes

CHANGES? NO This option allows the panel to automatically update Remote Link™ at the central station
with any changes made to the panel.
Select NET or DD to send local programming changes or User Menu changes to user codes,
SEND LOCAL
user proles, schedules, or holiday dates to Remote Link™ after exiting the programming or
NO NET DD User Menu. If NET is selected, changes are sent using Network. If DD is selected, changes
are sent using Dialer. Default is NO to disable this feature.

REMOTE CHANGE IP Remote Change IP

000.000.000.000 This option displays when NET is selected for Send Local Changes. Enter the IP address
containing up to 12 digits. The Net IP Address must be unique and cannot be duplicated on
the network. Enter all 12 digits and leave out the periods. Default is 0.0.0.0.

REMOTE CHANGE Remote Change Port

PORT: 2002 This option displays when NET is selected for Send Local Changes. Enter the Port number.
Valid numbers are from 0 to 65535. Default is 2002.

REMOTE PHONE NO. Remote Telephone Number

- This option displays when DD is selected for Send Local Changes. Press CMD to enter the
phone number the panel dials when sending programming changes. After entering a phone
number, the panel sends any panel changes to Remote Link™.
The phone number can have two lines of 16 characters each to equal 32. Enter a P to
program a two second pause in the dialing sequence. The P character counts as part of the
32 allowable characters. Enter *70P as the string rst characters to cancel call waiting. Dial
tone detect is an automatic panel function.

App Key
APP KEY: Enter the 8-digit App Key obtained in your Dealer Settings tab at
dealer.securecomwireless.com.
This option is a security feature of the Virtual Keypad iPhone/Android App used only
when your Dealer Settings at dealer.securecomwireless.com have EASYconnect set as the
Communication Type.
This communication option is only available for panels with onboard network and is used to
eliminate the need for a static IP address programmed in Network Options. To enter a new
App Key, press any select key or area and enter any combination of 8 digits. Press CMD.

ACTIVATE ONBOARD Activate Onboard Speaker

SPEAKER? NO YES Select YES to enable the onboard piezo speaker for local annunciation. Select NO to turn
the piezo o for all operations. This does not aect remote annunciator open collector
(RA) operation. The default is NO.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

25
CARD OPTIONS Card Options
DMP CUSTOM ANY Select DMP to allow only the DMP card format for access. The menu advances to REQUIRE
SITE CODE.
Select CUSTOM to disable DMP format and program slots 1-8 as needed. The menu
advances to FORMAT NO. The format that is programmed into slot 1 is the default format.
In the event that a card with an unrecognized format is programmed when adding a
credential, that card will be read in the format that is programmed in slot 1. To restrict card
reads to specic formats, only program slots 2-8.
Select ANY to allow all Wiegand card reads to activate the door strike relay. The relay is
activated for the length of time programmed in ZN 3 REX TIME. No user code information
is sent to the panel. The menu advances to NO COMM WITH PNL.

REQUIRE SITE Require Site Code (If Card Format is Set to DMP)
CODE: NO YES Press the select key or area under YES to use a site code.
In addition to User Code verication, door access is only granted when any one site code
programmed at the SITE CODE ENTRY option matches the site code received in the
Wiegand string.

NO COMM WITH PNL No Communication with Panel

OFF SITE ANY ON This option denes the relay action when communication with the panel has not occurred
for approximately ten seconds. Press any select key or area to display relay action options.
Press the Back Arrow key to return to the NO OF USER CODE DIGITS:.
Choose the action required:
NO COMM WITH PNL
OFF Press the rst select key or area to choose OFF [Default] (Relay Always O) — The relay
does not turn on when any Wiegand string is received. O does not aect any REX
operation.

Press the second select key or area to choose SITE (Accept Site Code) — Door access is
NO COMM WITH PNL
SITE granted when the Wiegand site code string received matches any site code programmed
at SITE CODE ENTRY. For details refer back to the REQUIRE SITE CODE option.
Press the third select key or area to choose ANY (Any Wiegand Read) — Door access is
NO COMM WITH PNL
ANY granted when any Wiegand string is received.

Press the fourth select key or area to choose ON (Relay Always On) — The relay is always
NO COMM WITH PNL
ON on.

Press CMD to display the next action.

NO COMM WITH PNL Press the rst select key or area to choose LAST (Keep Last State) — The relay remains in
LAST the same state and does not change when communication is lost.
After choosing the action, the NO COMM WITH PNL option and the newly dened action
display. Programming is now complete. Press CMD to display DEVICE NO.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

26
SYSTEM REPORTS
System Reports
SYSTEM REPORTS Select specic system reports the panel sends to the receiver.

Abort Report
ABORT NO YES YES allows the panel to send an alarm abort report to the receiver any time an area is
disarmed during Transmit Delay before an alarm report is sent and the Bell Cuto Time has
not expired. After disarming an area, if any other area remains armed and has zone(s) in
alarm, the alarm abort report is not sent. Abort Reports are not sent for Fire, Fire Verify, or
Supervisory type zones.

Restoral Reports
RESTORAL: YES This option allows you to control when and if a zone restoral report is sent to the central
station receiver. Press any select key or area to display the following options:
NO - Disables the zone restoral report option. Zones continue to operate normally but do
not send restoral reports to the receiver.
NO YES DISARM
YES - Enables the zone restoral report option. Zone restorals are sent whenever a zone
restores from a trouble or alarm condition.
DISARM - Causes the panel to send restoral reports for a non-24-hour zone whenever a
zone that has restored from a trouble or alarm condition is disarmed. All 24-hour zones
send restoral reports as they restore.

Bypass Reports
BYPASS NO YES YES allows the panel to send all zone bypasses, resets, and force arm reports to the
receiver. The bypass report includes the zone number, zone name, and the user name
and number of the individual operating the system. Reports are only sent if O/C User in
Communications is set YES for Receiver 1 or Receiver 2.

Schedule Change Reports

SCHD CHG NO YES YES allows the panel to send all schedule changes to the receiver. The report includes the
day, opening time, closing time, extend schedule time, and the user name and number of
the individual making the change.

Code Change Reports

CODE CHG NO YES YES allows the panel to send all code additions, changes, and deletions to the receiver. The
code change report includes the user name and number added or deleted and the user
name and number of the individual making the change. Reports are only sent if O/C User in
Communications is set YES for Receiver 1 or Receiver 2. The default setting is YES.

Access Keypads
ACCESS KEYPADS Select the keypad addresses (1 through 16) that send door access reports to the receiver.
Enter the keypad number using the digit keys. An asterisk next to the number indicates
that the keypad is selected. Press CMD to display the next set of keypads.
A report is sent with each door access made from the selected keypads. Keypads at
addresses not selected still operate the door relay but do not send access reports. The
report includes the user number, user name, keypad address, and device name.

Ambush
AMBUSH NO YES YES allows an ambush report to be sent anytime user code number 1 is entered at a
keypad. NO disables the ambush report and allows user number 1 to operate the same as
all other codes.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

27
LATE TO OPEN Late To Open
MINUTES: 0 Enter 1-240 as the number of minutes to elapse that the system may remain armed after
the opening time of a schedule without sending a Late To Open message. If the system
continues to be armed after the Late to Open minutes expire, a Late To Open message is
sent to the central station. Default is 0, which disables the Late To Open option.

EARLY TO CLOSE Early To Close

MINUTES: 0 Enter 1-240 as the number of minutes that the system can be armed prior to the scheduled
closing time. If the system is armed prior to the Early to Close minutes, an Early To Close
message is sent to the central station. Default is 0, which disables the Early to Close option.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

28
SYSTEM OPTIONS
System Options
SYSTEM OPTIONS This section allows you to select system-wide parameters.

System
SYSTEM: AREA This option allows you to program how the areas operate for arming and disarming. The
system types are:

AREA - All 32 areas can be programmed and operated independently.

AREA A/P H/A GST ALL/PERIMETER - Area 1 is the Perimeter and Area 2 is the Interior.

HOME/SLEEP/AWAY - Area 1 is the Perimeter, Area 2 is the Interior, and Area 3 is the
Bedrooms. With the HOME/SLEEP/AWAY option, the user can:
1. Select HOME to arm just the perimeter.
2. Select SLEEP to arm the perimeter and interior (non bedroom areas).
3. Select AWAY to arm all three areas.

A Home/Sleep/Away system can be congured to use all three areas or only use the Home
and Away areas.
HOME/SLEEP/AWAY WITH GUEST- This allows the alarm system to be divided into a main
house HOME/SLEEP/AWAY system and two other guest houses that also are set up as
HOME/SLEEP/AWAY systems.
Areas 1, 2, and 3 are the Perimeter, Interior, and Bedrooms for the Main house system. Areas
4, 5, and 6 are the Perimeter, Interior, and Bedrooms for the Guest 1 house system. Areas
7, 8, and 9 are the Perimeter, Interior, and Bedrooms for the Guest 2 house system. These
areas are automatically assigned per system and cannot be changed. See Display Areas in
Device Setup to assign keypads to a system. Zones are assigned to a system by assigning
the system’s area numbers to the zone in Zone Information programming.
When either All/Perimeter or Home/Sleep/Away is selected, the area names are
automatically assigned and cannot be modied.
Areas 3-32 in an All/Perimeter system, areas 4-32 in a Home/Sleep/Away system, and areas
9-32 in a Home/Sleep/Away with Guest system are not available for use and are initialized.

Instant Arming
INST ARM NO YES When YES is selected, the arming keypad displays INSTANT for selection during the exit
countdown delay when arming fewer than all areas of the system. At the time instant
arming is selected, any entry and exit delays programmed for the areas being armed are
ignored. The entry delay for previously armed areas is not aected by instant arming.
When NO is selected, INSTANT does not display during arming. Default is NO for an Area
System, and YES for an All/Perimeter or Home/Sleep/Away system.

Closing Wait
CLS WAIT NO YES When YES is selected, the keypad displays ONE MOMENT... while waiting for an
acknowledgement from the receiver before arming the selected area(s) and performing
a Bell Test (if selected). Exit delays begin after the Closing Wait. Opening/Closing reports
must be YES to enable Closing Wait.

ENTRY DLY 1: 30 Entry Delay 1

ENTRY DLY 2: 60 Enter the Entry Delay time for all Exit type zones programmed to use Entry Delay 1. When
an armed Exit type zone is faulted, the keypad prewarn tone begins sounding. All keypads
ENTRY DLY 3: 90 programmed to prewarn for that zone display ENTER CODE:- and the name of the zone
ENTRY DLY 4: 120 causing the entry delay. Entry Delay times can be from 30 to 250 seconds. Repeat the
above for each entry delay being used in the system. For UL Installations, the combined
Transmit Delay (Abort Window) and Entry Delay must not exceed one (1) minute.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

29
 Cross Zone Time
CRS ZONE TM: 4 Enter the time allowed between zone faults. When zones are cross zoned, the same zone
or a second cross zoned zone must fault within this time in order for an alarm report for
both zones to be sent to the receiver. If the cross zone time expires without the second
zone faulting, only a zone fault from the rst zone is reported. Cross-zone time can be from
4 to 250 seconds. Entering 0 (zero) disables this function. Default is 4. See the Appendix.

Zone Retard Delay

RETARD DELAY: 10 Enter the retard time assigned to Fire, Supervisory, Auxiliary 1, Auxiliary 2, Arming, and
Panic type zones. The retard delay only functions when the zone is shorted. The zone must
remain shorted for the entire length of the Retard Delay before being recognized by the
panel. The Zone Retard Delay can be from 1 to 250 seconds. Entering a 0 (zero) disables
this function.

Power Fail Delay

PWR FAIL HRS: 1 This option tracks the duration of an AC power failure. When the AC power is o for the
length of the programmed delay time, an AC power failure report is sent to the receiver.
The delay time can be from 1 to 15 hours. Entering a 0 (zero) sends the power failure report
after a 15-second delay. The default setting is 1.

Swinger Bypass Trips

SWGRBYPS TRIPS: 2 Enter the number of times (1-6) a zone can go into an alarm or trouble condition within one
hour before being automatically bypassed. Bypassed zones are automatically reset when
the area they are assigned to is disarmed. All 24-hour zones are reset when any area of the
system is disarmed. Entering 0 (zero) disables this function. Default is 2. A Bypass Report
is sent to the receiver if Bypass Reports is YES.

Reset Swinger Bypass

RST SBYP NO YES When YES is selected, an automatically bypassed zone is reset if it remains in a normal
condition for one complete hour after being bypassed. A report of the automatic reset is
sent to the receiver if Bypass Reports has been selected as YES. Default is NO.

Zone Activity Hours

ZN ACTY HRS: 0 This option provides supervision of a person living alone for non-activity. Enter the
number of hours, 0 to 9, allowed to elapse without a disarmed zone being tripped before a
message is sent to the receiver. Default is 0 (zero).
When the system is disarmed, the timer begins to countdown the number of hours
programmed. Each time activity occurs, the timer restarts the countdown. Before the
countdown time expires, the keypad sounds a tone and PRESS ANY KEY displays to allow
the user to restart the activity timer. The duration of the tone is the number of seconds
programmed for Entry Delay 2. Select the SUPV/TRBL receiver option in communication
programming to send S93 ALARM: User Activity Not Detected, S94 Alert: Activity Check
Enabled, and S95 Alert: Activity Check Disabled messages.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

30
 Time Zone Changes
TIME CHG NO YES This function allows the panel to request automatic time changes from the DMP SCS-1R
Receiver on Path 1. For the receiver to send time changes, it must be programmed to send
time changes and must be receiving time change updates from the network automation
computer at least every 24 hours. Default is YES.

When time zone is programmed YES, enter the number (0-23) that indicates the dierence
HRS FROM GMT: 6 between the Greenwich Mean Time (GMT) and where the panel is located. The default is 6.

GMT City/Time Zone GMT City/Time Zone

0 London, Monrovia, Lisbon, Dublin, Casablanca, Edinburgh 13 New Cadelonia
1 Cape Verde Island, Azores 14 Guam, Sydney
2 Mid-Atlantic, Fernando de Noronha 15 Tokyo, Seoul
3 Buenos Aires, Georgetown, Brasilia, Rio de Janeiro 16 Hong Kong, Singapore
4 Atlantic Time (Canada), Caracas, La Paz, Santiago 17 Bangkok, Hanoi
5 Eastern Time (US, Canada) Bogota, Lima, Arequipa 18 Dhaka, Almaty
6 Central Time (US, Canada), Mexico City, Saskatchewan 19 Islamabad, Karachi
7 Mountain Time (US, Canada), Edmonton 20 Abu Dhabi, Kazan
8 Pacic Time (US, Canada), Tijuana 21 Moscow, Bagdad
9 Alaska 22 Eastern Europe
11 Midway Island, Samoa, Hawaii* 23 Rome, Paris, Berlin
Fiji, Marshall Island, Wellington, Auckland, Kwajalein,
12
Kamchatka

*Arizona, Hawaii, American Samoa, Guam, Puerto Rico, and the Virgin Islands do not observe daylight savings time.

Latch Supervisory Zones

LATCH SV NO YES Selecting YES latches supervisory zone alarms on the keypad display until the sensor
reset operation is performed. Selecting NO automatically clears the alarm from the keypad
display when the supervisory zone restores to a normal condition. Default is YES.

Programming Menu Language

PROG LANGUAGE Press CMD to select the programming language.
The current primary programming language displays. The default language is English. Press
a Select key to change the primary programming language.
PRI LANG: ENGLISH
Select the primary programming language.
ENG = English (ENGLISH)
SPN = Spanish (ESPANOL)
FRN = French (FRANCAIS)
CZE = Czech (CESKY)
GRE = Greek (ΕΛΛΗΝΙΚΆ)
DUT = Dutch (NEDER)

The current secondary programming language displays. Selecting a secondary language

SEC LANG: NONE allows the installer to view programming in English, Spanish, or French. When the
Programming Menu is accessed, the installer is prompted to choose the programming
display language. If SEC LANG: is set to NONE, the option to choose a language does not
display. To select a secondary language, press the select key or area below the language.
Default is NONE.
Select the secondary programming language.
NONE = No secondary language options are displayed
ENG = English (ENGLISH)
SPN = Spanish (ESPANOL)
FRN = French (FRANCAIS)
CZE = Czech (CESKY)
GRE = Greek (ΕΛΛΗΝΙΚΆ)
DUT = Dutch (NEDER)

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

31
USER LANGUAGE User Menu and Status List Language
PRI LANG: ENGLISH Press CMD to select User Language.
The current primary user language displays. The default language is English. Press any
select key or area to change the primary User language.
Select the primary user language.
ENG = English (ENGLISH)
SPN = Spanish (ESPANOL)
FRN = French (FRANCAIS)
CZE = Czech (CESKY)
GRE = Greek (ΕΛΛΗΝΙΚΆ)
DUT = Dutch (NEDER)
The current secondary user language displays. Selecting a secondary user language allows
SEC LANG: NONE the user to view the User Menu and Status List text in English, Spanish, or French. When
the User Menu is accessed, the user is prompted to choose the display language. Status
List text displays in the selected language until another language is chosen. If SEC LANG:
is set to NONE, the option to choose a language does not display. To select a secondary
language, press the select key or area below the language. Default is NONE.
Select the secondary user language.
NONE = No secondary language options are displayed
ENG = English (ENGLISH)
SPN = Spanish (ESPANOL)
FRN = French (FRANCAIS)
CZE = Czech (CESKY)
GRE = Greek (ΕΛΛΗΝΙΚΆ)
DUT = Dutch (NEDER)

Bypass Limit
BYPASS LIMIT 0 Enter the maximum number of zones (0 to 8) that can be bypassed in any single area when
that area is being armed at a keypad. If more zones than the limit are in a non-normal state
or already bypassed at arming, arming does not occur and Arming Stopped displays. The
Bypass limit does not aect auto arming, keyswitch arming, or remote arming. Entering 0
(zero) allows no limit. Default is 0 (zero).

WIRELESS House Code

HOUSE CODE: 0 When using a DMP wireless system, enter a house code between 1 and 50. Default is 0
indicating no wireless system is being used. The DMP house code identies the panel, DMP
receiver, and DMP transmitters to each other. The DMP receiver listens for transmissions
that have the programmed house code and transmitter serial number. The transmitters may
take up to two minutes to learn the new house code and continue operation.

1100 ENCRYPTION Wireless Encryption

ALL BOTH NONE Encryption allows the panel to communicate with encrypted 1100 Series wireless devices.
Select ALL to allow encryption for all the wireless devices programmed into the panel.
Select BOTH to allow encryption for selected wireless devices programmed into the panel.
Select NONE to don’t allow encryption for wireless devices programmed into the panel.
The default is NONE.

1100 PASSPHRASE Enter Passphrase

******** ENTER PASSPHRASE displays if you select ALL or BOTH for wireless encryption. In order
for the panel to support encrypted 1100 Series wireless devices, a passphrase must be
entered. The passphrase must be an 8-digit hexadecimal number which determines the
system’s encryption key.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

32
DETECT WIRELESS Detect Wireless Jamming
JAMMING: NO YES This option displays when the House Code entered is for a DMP 1100 Series Wireless
system (1-50). When enabled and the wireless receiver detects jamming, a jammed trouble
(when disarmed) or jammed alarm (when armed) message displays in the Status List and
is sent to the central station receiver. Select YES to enable jamming messages to display in
the Status List. Select NO to disable jamming messages. Default is NO.

Trouble Audible Annunciation

TRBL AUDIBLE: DAY This option allows you to choose when trouble audibles will annunciate from the keypad.
This also includes AC Trouble for Fire Keypads, Battery Trouble, Panel Tamper, and other
System Troubles.
Press any top row key to select the keypad buzzer annunciation method for wireless low
battery and missing messages. Select ANY to enable annunciation anytime. Select DAY to
enable annunciation except during sleeping hours (9 PM to 9 AM). Select MIN (minimum)
to annunciate only Fire and Fire Verify zones during daytime hours (9 AM to 9 PM). Default
is DAY.

KEYPAD PANIC KEYS

Enable Keypad Panic Keys
ENABLED: NO YES This option allows the panic key operation selected at the keypad to send the Panic,
Emergency, or Fire message to the central station receiver. Select YES to enable the two-
button panic operation to operate. To disable the panic operation, select NO. Default is
YES.

OCCUPIED Occupied Premises

PREMISES: NO YES For All/Perimeter or Home/Sleep/Away systems, select YES to allow the panel to
automatically disarm the interior area(s) when arming all areas and a perimeter zone is not
tripped during the exit delay.
This False Alarm Reduction feature will keep a user from arming the entire system when
they do not exit and remain in the premises. Select NO to disable this feature. Default is
YES.
With a Home/Sleep/Away with Guest arming system, this feature only applies to the main
system.

ENHANCED ZONE Enhanced Zone Test

TEST: NO YES Select YES to allow enhanced zone test operation for Walk Test (8144), Panic Test, and
Burglary Zone Test in the User Menu. The default is NO.
Enhanced operation allows:
• A Verify message to be sent each time a zone is tested. If a zone is tripped multiple
times, a Verify message is sent for each trip. This allows the Central Station to record the
number of devices per zone.
• The Verify message for each zone test to be sent at the time the trip occurs instead of at
the end of Walk Test.
• The System Test Begin and System Test End Central Station messages indicate the type
of zone being tested. The System Test Begin message also includes the user name and
number.

SEND 16 CHAR Send 16 Character Names

NAMES: NO YES This option allows central stations to select being sent either the rst 16 characters of the
name eld or the entire programmed name, up to 32 characters, for user name, user prole,
zone name, area name, output name, and group name.
Select YES to have the rst 16 characters of the name eld sent to the central station.
Select NO to send the exact number of characters entered in the name eld from 1 up to
the maximum of 32 characters. Default is YES.
Before using names longer than 16 characters, determine whether the Host Automation
System of your Central Station can accept 17 to 32 character names. If not, only use 16
character names.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

33
KEYPAD ARMED LED Keypad Armed LED
ANY ALL This option displays only when using an Area system. Press any top row key to select the
operation of the Armed LED on the keypad. Select ALL to require all keypad display areas
to be armed before the keypad Armed LED turns on. Select ANY to turn on the keypad
Armed LED when any keypad display area is armed. Default is ALL.

USE FALSE ALARM Use False Alarm Question

QUESTION NO YES This option allows users to investigate a burglary alarm prior to disarming the system and
send an Alarm Veried or Alarm Cancelled message to the Central Station.
Select YES to display IS THIS A FALSE ALARM? NO YES when a burglar alarm occurs.
Select NO to display CANCEL VERIFY. Default is YES.

When a burglar alarm occurs in an area system and a user code is entered at a keypad
Status List, keypads programmed as KPD in Device Setup display IS THIS A FALSE
ALARM? NO YES or CANCEL VERIFY. The option is not displayed at devices programmed
as DOOR. Selecting NO or Verify sends an alarm message to the Central Station. Selecting
YES or CANCEL sends an alarm cancelled message to the Central Station and disarms the
areas that the user has the authority to disarm. This display remains on the keypad until
a selection is made, the Back Arrow is pressed, or the internal system bell cuto timer
expires.

ALLOW OWN USER Allow Own User Code Change

CODE CHG? NO YES This option allows users without user code authority to change their own user code. When
YES is selected, the User Code menu displays USER CODE: ***** at the keypad to allow that
user to change their own code. If NO is selected, the user cannot change their personal
user code. Default is NO.

PANIC SUPERVISION Panic Supervision

NO YES Select YES to enable a 30 day supervision of the Model 1145-1-B-PSV key fob. Default is
NO.
This option allows a key fob that is lost or has a dead battery to be identied at the Central
Station host automation system as a missing transmitter, without the need to apply a
supervision time in zone information programming. A supervision message is automatically
sent from the key fob to SCS-VR every four hours, resetting the 30 day countdown timer
for that key fob serial number. If the 30 day timer expires for a key fob serial number,
SCS-VR will generate a zone missing message to the host automation system.

ENTER WEATHER Weather Zip Code

ZIP CODE: 0 This option allows local U.S.A. weather updates to display on the keypad. Enter the zip
code of the user at this option. When no number is entered weather conditions are not
displayed. Default is 0.
If using a 7800 Series keypad, the current weather conditions and the next day’s forecast
display as graphics on the Main Screen. All other DMP keypads display the weather
information in the Status List.

EOL Selection
EOL VALUE: XXXX Select the resistance value in kOhms that the system will expect for end of line resistors.
Values can be set at either 1k, 2.2k, 3.3k, or 4.7k. This adjusts the voltage threshold used to
determine open, short, or normal zone conditions for zones 1-8 on XR International Series
panels. Default is 1k.
Zones 9-10 on XR International Series panels are defaulted to 3.3k.

Celsius Temperature Option

CELSIUS: NO YES This option determines whether the panel should use Celsius Units for displayed
temperatures and for sending temperatures to Z-Wave thermostats. The default is NO.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

34
INTRUDER VERIFY Intruder Conrmation Time
TIME: XXX If two zones trip within the specied time frame, then it is considered a veried alarm
and authorities will respond. Intruder conrmation times can be from 30-60 minutes. The
default is 0.

HOLD UP VERIFY Hold Up Conrmation Time

TIME: XXX If two panic type zones trip within the specied time frame, then it is considered a veried
alarm and authorities will respond. Holdup conrmation times can be from 8-20 hours. The
default is 0.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

35
BELL OPTIONS
Bell Options
BELL OPTIONS This section allows you to program the panel bell output functions.

Bell Cuto Time

BELL CUTOFF: 15 Enter the maximum time from 1 to 99 minutes the Bell Output remains on. If the area is
disarmed, the cuto time resets. Enter 0 (zero) to provide continuous bell output. The
default is 15 minutes. To support the Cancel Verify feature on an All/Perimeter or Home/
Sleep/Away system, set the Bell Cuto Time to greater than 0.

Automatic Bell Test

BELL TST NO YES Select YES to turn on the Bell Output for 2 seconds each time the system is armed
from a keypad. This test is delayed until the Closing Wait acknowledge is received (if
programmed). If the Closing Wait acknowledge is not received within 90 seconds, the bell
test does not occur. Arming performed from an Arming zone or from Remote Link™ does
not activate the Bell Test.

Bell Output
BELL OUTPUT: 0 Enter the output/Favorite number when needed to follow the panel Bell Output operation
for all action and o conditions. Enter 0 (zero) to disable.

Bell Action
BELL ACTION . . . . . This section denes the type of Bell Output for zone alarms. Press CMD to display the
default Bell Output for each zone type. Press any select key or area and enter S for a
Steady Bell Output, P for a Pulsed output, T for a Temporal Code 3 output, 4 for a Temporal
Code 4 output, and N for no Bell Output (default). Enable this feature to latch a bell action
to a keypad for Panic zones. Trouble conditions do not activate the Bell Output.

Fire Bell Action

FIRE TYPE: T Denes Bell Action for Fire Type zones. The default is T.

Burglary Bell Action

BURGLARY TYPE: S Denes Bell Action for Burglary Type zones and Exit Error output. The default is S.

Supervisory Bell Action

SUPRVSRY TYPE: N Denes Bell Action for Supervisory Type zones. The default is N.

Panic Bell Action

PANIC TYPE: N Denes Bell Action for Panic Type zones. The default is N.

Emergency Bell Action

EMERGNCY TYPE: N Denes Bell Action for Emergency Type zones. The default is N.

Auxiliary 1 Bell Action

AUXLRY 1 TYPE: N Denes Bell Action for Auxiliary 1 Type zones. The default is N.

Auxiliary 2 Bell Action

AUX 2 TYPE: N Denes Bell Action for Auxiliary 2 Type zones. The default is N.

Carbon Monoxide (CO)

CO TYPE: 4 Denes Bell Action for Carbon Monoxide (CO) Type Zones. The default is set at 4.

Strobe
STROBE: NO YES Denes whether or not a system is using a strobe on site. The default is NO.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

36
OUTPUT OPTIONS
Output Options
OUTPUT OPTIONS This section allows you to program panel output options. The panel provides two Form
C relays (1 and 2) and four switched ground (open collector) outputs numbered 3 to 6.
Expand the system up to 500 additional relay outputs using any LX-Bus on the panel,
or multiple 716 Output Expander Modules. In addition, 45 wireless outputs are available
when using the 1100XINT Series wireless receiver. Refer to the XR150INT/XR550INT Series
Installation Guide (LT-1233INT) for complete information.
Select from the following output numbers:
• 1 to 6 — Onboard panel outputs
• 450 to 474 — Slow response time* wireless outputs (activates within 15 seconds)
• 480 to 499 — Fast response time* wireless outputs (activates within 1 second)
• 500 to 999 — LX-Bus output, Relay output, Zone expansion output
• D01 to D16 — Keypad door strike relay for addresses 1-16
• F1 to F20 — To activate Z-Wave Favorites
• G1 to G20 — Output group
* The response time of a wireless output is the time it takes for a wireless output to activate
once the panel event occurs. You determine whether a wireless output is a slow or fast
response based on the output number assigned. A slow response output number extends
battery life, but response time may be up to 15 seconds. A fast response output number
responds within 1 second, but reduces battery life. Refer to the specic wireless output
installation guide to determine battery life. Output response times are programmed in
Output Information.

Cuto Output
CO OUTS: - - - - - - Outputs 1 to 6 can be entered here to turn o after a time specied in CUTOFF TIME. To
disable this option, press any select key or area to clear the display then press CMD. The
Cuto Output displays dashes when no outputs are selected.

Output Cuto Time

CUTOFF TIME: 0 If a Cuto Output (1-6) is assigned, enter a Cuto Time of 1 to 99 minutes for the output to
remain on. Enter 0 (zero) for continuous output.

Communication Trouble Output

COM FAIL OUT: 0 Enter the output/Favorite number to turn on when a DD system fails to communicate on
three successive dial attempts or if the backup communication line transmits a report.
The Communication Trouble Output also turns on when NET is selected as the primary
communication method and NET communication fails after one minute. When NET
communication is restored the Communication Trouble Output automatically turns o.
To manually turn the output o, disarm any area or select O for the output number in the
User Menu Outputs On/O section. Enter 0 (zero) to disable this output.

Fire Alarm Output

FIRE ALR OUT: 0 Enter the Output/Favorite number to turn on when a re type zone is placed in alarm. The
output is turned o using the Sensor Reset option while no additional re type zones are in
alarm. Enter 0 (zero) to disable. This output is not compatible with Cuto Outputs.

Fire Trouble Output

FIRE TRB OUT: 0 Enter the output number to turn on when a re type zone is placed in trouble, when a
supervisory type zone is placed in trouble, or when any system monitor (AC, Battery, Phone
Line 1 or Phone Line 2) is placed in trouble. The output turns o when all re and supervisory
type zones, or system monitors are restored to normal. Enter 0 (zero) to disable this output.
This output is not compatible with Cuto Outputs. This output can be connected to a lamp,
LED, or buzzer using the DMP Model 716 Output Expansion Module.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

37
 Panic Alarm Output
PANIC ALM OUT: 0 Enter the output/Favorite number to turn on when any Panic type zone is placed in an
alarm condition. The output is turned o after all Panic zones are restored from an alarm
condition and a Sensor Reset is performed. Enter 0 (zero) to disable.
Wireless Outputs
• The Panic Alarm is compatible with the Model 1118 Wireless Remote Indicator Light and
the Model 1116 Wireless Relay Output connected to a Model 572 Indicator LED.
• When a Panic Alarm occurs, the LED turns on steady for ve minutes and then turns o.
• When a Panic Test is initiated from the keypad, the LED ashes quickly for ve minutes.
• For a Panic Alarm, a fast response wireless output number is recommended.

Ambush Output
AMBUSH OUT: 0 Enter the output/Favorite number to turn on when an Ambush code is entered at a keypad.
The output is turned o using the Sensor Reset option. Enter 0 (zero) to disable.

Entry Output
ENTRY OUT: 0 Enter the output/Favorite number to turn on at the start of the entry delay time. The
output turns o when the area is disarmed or the entry delay time expires. Enter 0 (zero)
to disable.

Begin Exit Output

BEG EXIT OUT: 0 This output/Favorite turns on any time an exit delay time starts. The output turns o when
the system arms or when the arming has been stopped. Enter 0 (zero) to disable.

End Exit Output

END EXIT OUT: 0 This output/Favorite turns on any time an exit delay time ends. The output turns o when
the system disarms. Enter 0 (zero) to disable.

Ready Output
READY OUT: 0 Enter the output/Favorite number to turn on when all disarmed burglary zones are in a
normal state. The output is turned o when any disarmed burglary type zone is in a bad
state. Enter 0 (zero) to disable. This output is not compatible with Cuto Outputs.

ARMED HOME: 0 Armed Output

ARMED SLEEP: 0 The entered output turns on any time the system is armed. The programming prompt
displayed is dependent on the system’s arming type.
ARMED AWAY: 0
ARMED ALL: 0 For Home/Away systems, only the HOME and AWAY screens display. If a Bedroom area is
programmed into the panel, the SLEEP screen also displays. For All/Perimeter systems, the
ARMED PERIM: 0 ALL and PERIM screens display. For Area systems, the ARMED OUT screen displays.
ARMED OUT: 0
All options are defaulted to 0 (zero). The output turns o when the system completely
disarms. Enter 0 (zero) to disable this output.

Disarmed Output
DISARMED OUT: 0 This output/Favorite turns on when all areas of the panel are disarmed. The output turns
o when an area is armed.

Telephone Trouble Output

PH TRBL OUT: 0 Enter the output/Favorite number to turn on when the phone line monitor on the panel
phone line is lost. Enter 0 (zero) to disable this output.

Late To Close Output

LATE CLS OUT: 0 Enter the output/Favorite number to turn on at the expiration of a Closing schedule. The
output activates simultaneously with the CLOSING TIME! keypad display. The output is
turned o when the area is armed, the Closing is extended, or the schedule is changed.
Enter 0 (zero) to disable this output.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

38
 Device Fail Output
DVC FAIL OUT: 0 Enter the output/favorite number to turn on when an addressed device fails to respond
to polling from the panel. A Missing Device report is sent to the receiver and is stored as
an event in the panel. The output is turned o when the device responds to polling or is
removed from programming in the system. Enter 0 (zero) to disable this output and LX-
Bus™ device fail reporting to the receiver. If any addressed device is unsupervised, this
output cannot be used.

Sensor Reset Output

SNSR RST OUT: 0 Enter the output/Favorite number to turn on when a Sensor Reset is performed at a
keypad. The output turns o automatically 5 seconds later. This function can be used to
reset smoke detectors that are operated by an external power supply through a Model 716
Output Expander Module. Enter 0 (zero) to disable this output.

Closing Wait Output

CLS WAIT OUT: 0 Enter the output/Favorite number to turn on for approximately four (4) seconds when
Closing Wait is programmed as YES and the panel successfully communicates the closing
message at arming. If the closing message does not communicate successfully, this output
does not turn on.

Arm-Alarm Output
ARM-ALARM OUT: 0 Enter the output/Favorite number to turn on steady when any area of the system is armed.
If an alarm occurs causing the keypads to turn Red, this output pulses and continues to
pulse for approximately ve (5) minutes after the panel is disarmed. Enter 0 (zero) to
disable.
To operate the Arm-Alarm output within one second, program a fast response number
from 480 to 499. Fast response operation reduces overall wireless output battery life.
To operate the Arm-Alarm output within 15 seconds, program a slow response number
from 450 to 474. Slow response operation increases overall wireless output battery life.
Supervisory Alarm Output
SUPV ALM OUT: 0 Enter the output/Favorite number to turn on when a supervisory zone type is placed into
an alarm. The output turns o when all supervisory type zones are restored to normal.
Enter 0 (zero) to disable. Default is 0.

HEAT SAVER Heat Saver Temperature

TEMPERATURE: 0 Enter the desired temperature setting for all Z-Wave thermostats when the system is
armed ALL or AWAY. When the system is disarmed the thermostats return to their
previous settings. The range is 1-99 degrees. Enter 0 (zero) to disable.

COOL SAVER Cool Saver Temperature

TEMPERATURE: 0 Enter the desired temperature setting for all Z-Wave thermostats when the system
is armed ALL or AWAY. When the system is disarmed the thermostats return to their
previous settings. The range is 1-99 degrees. Enter 0 (zero) to disable.

OUTPUT OPTIONS Carbon Monoxide Alarm Output

CO ALRM OUT: XXX This output turns on any time a Carbon Monoxide Zone (CO) is placed in alarm. The output
is turned o using Sensor Reset option while no additional CO type zones are in alarm.

OUTPUT OPTIONS Lockdown Output Alarm Output

LOCKDOWN OUT: XXX This output turns on any time a Lockdown Output Zone is placed in alarm. The output
is turned o using Sensor Reset option while no additional Lockdown type zones are in
alarm.

OUTPUT OPTIONS Zone Monitor Output

ZN MNTR OUT: XXX This output turns on momentarily when a zone monitor tone is activated on keypads. If
zone monitoring is turned o, the zone monitor output will not trigger. When a sensor reset
is performed, the alert message wil be cleared from the status list.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

39
OUTPUT INFORMATION
Output Number
OUTPUT NUMBER Enter an output number. Entry range is 1 to 6, 450 to 474, 480 to 499, 500 to 999.
In order for wireless output troubles to display at a keypad, the keypad address must be
specied at the Auxiliary 1 Zones option in the Status List programming.

Output Name
OUTPUT NAME This section allows you to dene a 32 character alphanumeric name for any output
numbers. See the XR150INT/XR550INT Users Guide (LT-1278INT) Appendix for browser
operation.

OUTPUT REAL-TIME Output Real-Time Status

STATUS NO YES Selecting YES allows Real-Time Status reports of a hardwire device, such as Output ON,
OFF, PULSE, or TEMPORAL to be sent using PC Log reports. Selecting NO disables Real-
Time Status for this output device. Default is NO.

Serial Number
SERIAL#: XXXXXXXX If a house code is programmed in system options, then this option and the next option
only display when the output number entered is for a wireless output. Enter the eight-digit
serial number found on the wireless device.
ALREADY IN USE Already In Use displays when the serial number is already programmed for another output.
OUTPUT NO: XXX
The programmed output number displays.

SUPERVSN TIME: 240 Supervision Time

0 3 60 240 Press any select key or area to select the supervision time required for the wireless output.
Press CMD to accept the default time. Default is 240 minutes.
Select the required number of minutes. The transmitter must check in at least once
during this time or a missing condition is indicated for that zone. Zero (0) indicates an
unsupervised transmitter. The 3 minute supervision time is only available if using an 1135
Wireless Siren.
When the panel is reset, a receiver is installed or powered down and powered up, or
programming is complete, the supervision timer restarts for all wireless outputs.

TRIP WITH PANEL Trip with Panel Bell Option

BELL NO YES This option displays when the wireless device is an 1135 wireless siren. Select YES to have
the 1135 wireless siren follow the panel’s bell output cadence for the zone type and bell
cuto time up to 15 minutes. Default is YES.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

40
OUTPUT GROUPS
Output Groups
OUTPUT GROUPS This function allows you to assign outputs to groups. Output groups can be assigned to
other areas of programming such as Output Options or Alarm Action of Zone Information,
just like single outputs are assigned. This allows the entire group of outputs to turn on and
o as required by the programming option.

Group Number
GROUP NO: - Enter a group number from 1 to 20. Up to 20 dierent groups may be assigned.

Group Name
GROUP NAME X X The group name displays. To change the default name, press any select key or area then
enter up to 32 characters for the group name. Press CMD to enter the outputs to be
assigned to the group.

Output Number
OUTPUT NO: 1 Enter the Output number. Entry range is 1 to 6, 450 to 474, 480 to 499, 500 to 999
(outputs), F1 to F20 (favorites), D01 to D16 (doors), and G1 to G20 (groups). The maximum
number of outputs that can be assigned to a specic group is eight.
An output group may be assigned as one of the output numbers in another output group.
Output groups 1 to 10 can be assigned by a user prole for applications such as elevator
control. See the XR150INT/XR550INT Users Guide (LT-1278INT) Output Group section for
additional information.
Output groups 11 to 20 cannot be assigned to a prole and are available for installation
applications such as special lighting, etc.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

41
MENU DISPLAY
Menu Display
MENU DISPLAY Menu Display allows you to select at which keypad addresses the user can access the
following functions.
To select a keypad, enter the device number (keypad address) using the digit keys on the
keypad. When a keypad is selected, an asterisk appears next to the keypad address. Enter
the number again to deselect the keypad. Press CMD to display the next set of keypads (9
through 16). Refer to the Multiple Displays section at the beginning of this document.

Armed Status
ARMED STATUS Enter the keypad addresses (1 through 16) that show the armed areas. The User Menu
Armed Areas function also displays the custom area name you enter in Area Information.
*1 *2 *3 *4 When only areas one to eight are used, the Armed Status display is 1 2 3 4 5 6 7 8. When
*5 *6 *7 *8 areas nine or higher are used the system Armed Status display reads ALL SYSTEM ON or
SYSTEM ON. Press CMD to display additional areas.
*9 *10 *11 *12
*13 *14 *15 *16

Time
TIME DISPLAY
Enter the keypad addresses that can display the time and day of the week.
*1 *2 *3 *4
*5 *6 *7 *8

*9 *10 *11 *12

*13 *14 *15 *16

Arm/Disarm
ARM/DIS DISPLAY Enter the keypad addresses from which users can arm and disarm areas.

*1 *2 *3 *4
*5 *6 *7 *8

*9 *10 *11 *12

*13 *14 *15 *16

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

42
STATUS LIST
Status List
STATUS LIST This function allows you to select the zone alarms and troubles, and system monitor
troubles displayed at the keypads. The Status List function operates automatically when
the keypad is not performing any other function.
The keypad stays in the Status List until the user arms, disarms or selects a menu option.
Status List alternates with the Armed Status on keypad addresses selected in the Menu
Display - Armed Status section. You can choose to have System Monitor troubles placed in
the list, the dierent zone types placed in the list, and at which keypad addresses they dis-
play.
To select a keypad, enter the device number (keypad address) using the digit keys on the
keypad. When a keypad is selected, an asterisk appears next to the keypad address. Enter
the number again to deselect the keypad. Press CMD to display the next set of keypads (9
through 16). Refer to the Multiple Displays section at the beginning of this document.

Display Keypads
DISPLAY KEYPADS This option denes which keypad addresses display the various status information. Any
combination of addresses can be entered to display the status items that follow. If you do
not want a particular status item to display, do not enter any addresses.

System Monitor Troubles

SYSTEM TROUBLES Species the keypad addresses (1 through 16) where any trouble on a System Monitor dis-
plays. The System Monitors include the following:
*1 *2 *3 *4 • AC Power
• Battery Power
*5 *6 *7 *8
• Closing Check
*9 *10 *11 *12 • Panel Box Tamper
*13 *14 *15 *16 • Phone Line 1
• Phone Line 2 (requires the 893A Dual Phone Line Module)
• Wireless Receiver Trouble
• Wireless Jamming Trouble or Alarm
The System Monitor name is placed in the Status List and the keypad steady trouble buzzer
sounds. The buzzer remains on until any select key or area is pressed. The name remains in
the list until the condition is restored. The buzzer sounds at 10:00 am daily until the system
trouble is cleared from the Status List.

Fire Zones
FIRE ZONES: Species the keypad addresses (1 through 16) where all re zone alarms and troubles
display. The zone name displays and, if it is a trouble condition, the keypad steady trouble
buzzer sounds. The buzzer remains on until any select key or area is pressed and a user
code is entered. If a trouble condition remains in the display, the buzzer sounds at 10:00
am daily until the trouble is cleared from the Status List.

Burglary Zones
BURGLARY ZONES: Species the keypad addresses (1 through 16) where all burglary zone alarms and troubles
display. Burglary zones include Night, Day, and Exit type zones. Burglary zone troubles
remain in the list until the zone restores. All keypads are selected by default.
For zone alarms, only the last burglary zone tripped remains in the list. The alarm remains
in the list until another burglary zone goes into alarm, any area of the system is disarmed,
or 10 minutes elapse without an alarm. This ensures that if a burglary is in progress the last
zone tripped remains in the list even if the zone is restored.
The keypad buzzer sounds for one second on burglary alarms.
You can further dene which keypad address shows a Burglary Zone event by entering that
area number in the Display Areas menu during Device Setup.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

43
 Supervisory Zones
SPRVISORY ZONES: Species the keypad addresses (1 through 16) where all supervisory zone alarms and
troubles display. Supervisory zones are entered in the status list and sound the keypad
buzzer until a valid user code is entered at any keypad address. If a trouble condition
remains in the display, the buzzer sounds at 10:00 am daily until the supervisory trouble is
cleared from the Status List.

Panic Zones
PANIC ZONES: Species the keypad addresses (1 through 16) where all panic zone alarms and troubles
display. The name of the zone remains in the list until a Sensor Reset is performed. The
keypad will sound if the Bell Action is enabled in Bell Options.

Emergency Zones
EMERGENCY ZONES: Species the keypad addresses (1 through 16) where all emergency zone alarms and
troubles display. The name of the zone remains in the list until the zone restores. The
keypad buzzer does not sound for emergency alarms or troubles.

Auxiliary 1 Zones
AUX 1 ZONES: Species the keypad addresses (1 through 16) where all Auxiliary 1 zone alarms and
troubles display. The name of the zone remains in the list until the zone restores. The
keypad buzzer does not sound for Auxiliary 1 alarms or troubles. You can further dene
which keypad address shows an Auxiliary 1 Zone event by entering that area number in the
Display Areas menu during Device Setup.

Auxiliary 2 Zones
AUX 2 ZONES: Species the keypad addresses (1 through 16) where all Auxiliary 2 zone alarms and
troubles display. The name of the zone remains in the list until the zone restores. The
keypad buzzer does not sound for Auxiliary 2 alarms or troubles.
You can further dene which keypad address shows an Auxiliary 2 Zone event by entering
that area number in the Display Areas menu during Device Setup.

Carbon Monoxide Zones

CO ZONES: Species the keypad addresses (1 through 16) where all carbon monoxide zone alarms
and troubles display. Carbon monoxide zones are entered in the status list and sound
the keypad buzzer until a valid user code is entered at any keypad address. If a trouble
condition remains in the display, the buzzer sounds at 10:00 am daily until the carbon
monoxide trouble is cleared from the Status List.

COMM PATH TRBL: Communication Trouble

NO YES ALL Species when communication troubles are displayed on keypads that are programmed to
display System Monitor Troubles. Default is NO.
Select YES to display communication trouble when any communication path fails.
Select ALL to display communication trouble only when all paths have failed.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

44
PC LOG REPORTS
PC Log Reports
PC LOG REPORTS This section allows you to program the types of PC Log Reports the panel sends through
the ETHERNET Port directly on the panel. The reports include information such as the type
of activity, time and date of the activity, and user name and number. These data reports
can be accessed from a PC using the Advanced Reporting Module. See the XR150INT/
XR550INT Series Installation Guide (LT-1233INT) for detailed Ethernet setup information or
the XR150INT/XR550INT Users Guide (LT-1278INT) for more information.
If there is trouble with the network connection, the panel continues to attempt to send the
PC Log Reports until the connection is reestablished. The panel then sends the reports. A
Network Trouble message is NOT sent if the connection is lost since this report tool is not
designed to be monitored by a receiver. The PC Log Reports have the lowest priority of
panel reports sent.
The PC Log Address String entered CANNOT be the same as that entered in
Communication. The PC Log Reports option should NOT replace the primary
communication method or act as a backup communication method.

NET IP ADDRESS Net IP Address

000.000.000.000 This option displays when the Communication Type for PC Log Reports is NET. Enter the
IP address containing up to 16 characters. The Net IP Address must be unique and cannot
be duplicated on the network. Enter all 12 digits and leave out the periods. The default is
0.0.0.0.

Net Port
NET PORT 2001 This option displays when Communication Type for PC Log Reports is Net. Enter the Port
number. Valid numbers are from 0 to 65535. Default is 2001.

Arm and Disarm Reports

ARM/DIS NO YES Sends arming, disarming and Late to Close events. Includes the area number, name and
action, the user number and name, and the time and date.

Zone Reports
ZONE NO YES Sends changes in the status of active zones. Includes the zone number, name, type, the
action (alarm, trouble, bypass, etc.), user number (if applicable), and area name. For a Walk
Test, zone verify and zone fail messages are sent for each zone.

User Command Reports

USR CMDS NO YES Sends user code changes, schedule changes, and door access denied events.

Door Access Reports

DOOR ACS NO YES Sends door access activity: door number, user number and name, and time and date.

Supervisory Reports
SUPV MSG NO YES Sends system monitor reports, such as AC and battery, and system event reports.
Supervisory Reports also sends the following reports:
• Abort
• Exit Error
• Ambush
• System Recently Armed
• Alarm Bell Silenced
• Unauthorized Entry
• Late to Close*
*Only sent as a Supervisory Report if Area Schedules is not enabled, Closing Check is
enabled, and an opening/closing schedule has been programmed.
To send these reports to the PC Log, you must enable SUPV MSG.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

45
PC LOG REAL-TIME PC Log Real-Time Status
STATUS NO YES Select YES to send Real-Time Status reports for zones, doors, and outputs. The specic
reports must also be selected by individual zone or output. The Real-Time Status messages
are sent to a PC running a graphic display software. Default is NO.
The messages that can be sent are:
• Door Open with zone number
• Door Closed with zone number
• Door Open with door number
• Door Closed with door number
• Output On
• Output O
• Output Pulse
• Output Temporal

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

46
AREA INFORMATION
Area Information
AREA INFORMATION Allows you to activate areas and assign functions to the dierent areas in the system. All
non-24-hour zones must be assigned to an active area. See Zone Information.
You activate an area by assigning it a name.

Exit Delay
EXIT DELAY: 60 Enter the exit delay time for all Exit type zones in this area. When the exit delay time starts,
all activity on that zone and other non-24-hour zone types in the area is ignored until the
exit delay expires. The keypad displays the Exit Delay time countdown and annunciates
the Exit Delay tone at 8 second intervals until the last 10 seconds when annunciation is at 3
second intervals.
The exit delay can be from 30 to 250 seconds. Default is 60 seconds.
During Exit Delay, if an exit zone trips, then restores, and trips again, the Exit Delay timer
restarts. This restart can occur only once.
Exit Error Operation: At arming, when an entry/exit zone (EX) is faulted at the end of the
exit delay then one of two sequences occur:
For Entry Delay 1 EX type zones:
• The bell sounds for the length of time set in Bell Cuto programming
• The Entry Delay operation starts requiring code entry to disarm
• If not disarmed, a zone alarm and an exit error are sent to the receiver
For Entry Delay 2-4 EX type zones:
• The zone is force armed and a zone force arm message is sent to the receiver
• An Exit Error is sent to the receiver
• The bell sounds for the length of time set in Bell Cuto programming

Closing Check
CLS CHK NO YES Select YES to enable the panel to verify that all areas in the system are armed after
permanent or extended schedules expire. If the Closing Check nds any areas disarmed
past the scheduled time, the keypads selected to display System Trouble Status displays
CLOSING TIME! and emits a steady beep. When Area Schedules is set to YES in Area
Information, the specic area and name display followed by — LATE.
When Auto Arm is NO, if within ten minutes the system is not armed or if the schedule is
not extended, a Late to Close report is sent to the SCS-1R Receiver. When Auto Arm is YES,
the area arms.
If the area becomes disarmed outside of any schedule, the Closing Check sequence occurs
after the Late Arm Delay time.
When Closing Check is NO and Auto Arm is YES, the system immediately arms when the
schedule expires. No warning tone occurs.
In addition, when Closing Check is NO, the option to extend a schedule does not display
when the schedule expires.

Closing Code
CLS CODE NO YES When YES is selected, a code number is required for system arming. If NO is selected, a
code number is not required for system arming.

Any Bypass
ANY BYPS NO YES When YES is selected, zones can be bypassed without a code number during the arming
sequence. A code number is always required to use the Bypass Zones option from the
menu.

Area Schedules
AREA SCH NO YES Select YES to allow each area to follow individual sets of area schedules programmed in
the User Menu. Select NO for all areas to follow only one set of schedules in the User Menu.
See the panel User Guide (LT-1278INT) to add schedules to the panel. Area Schedules are
not designed to operate with All/Perimeter or Home/Sleep/Away systems.
XR150INT/XR550INT Series Programming Guide Digital Monitoring Products
47
 Early Morning Ambush (Network Panels Only)
EARLY AMBUSH: 0 Enter the number of minutes (1 to 15) before a silent alarm (Early Morning Ambush S33)
is sent to the central station using the area 1 account number. Enter 0 (zero) to disable this
option.
When a user code is entered to disarm area 1 at a keypad or reader with Access Areas
assigned to area 1, the same or dierent user code must be entered within the programmed
number of minutes to prevent an ambush message from being sent to the receiver. The
second user code also must have authority to disarm area 1.
In addition, a zone activation with Alarm Action Message C also cancels the Early Morning
Ambush timer and stops an Ambush message from being sent to the receiver. See Report
to Transmit section in Zone Information.
The keypad does not display any indication that the ambush timer is running.
Indications can be provided by assigning an output number to Entry Out and Ambush Out
in Output Options. Entry Out turns on one minute before the timer expires and turns o at
expiration. Ambush Out turns on at the timers’ expiration and turns o when Sensor reset
is performed.

Area Number
AREA NO: - Enter the number of the area to program. Press CMD to continue. Only Area systems allow
the area name to be changed. When All/Perimeter or Home/Sleep/Away is selected as the
system type, the Area Number does not display.

All/Perimeter Programming
INT PERIM When All/Perimeter is selected as the system type, program the Interior and Perimeter
areas as needed.

Home/Sleep/Away Programming
INT BDRM PERIM When Home/Sleep/Away is selected as the system type, program the Interior, Bedroom,
and Perimeter areas as needed.

Area Name
* UNUSED * The area name can be up to 32 alphanumeric characters. To add an area name to the system,
press any select key or area and then enter up to 32 characters for the new area name. Press
CMD to continue. Inactive areas are marked * UNUSED *. Only systems programmed for Area
arming have the option available to change the area name.
To mark an active area unused, press any select key or area to delete the old name, then
press CMD. The programmer automatically programs the name as *UNUSED*. If you have
already cleared Area Information during Initialization, all areas are marked * UNUSED *.
Home/Sleep/Away with Guest systems display the area name, but the names cannot be
changed. The following are the display names that appear on the keypad:

Area Display Area Display Area Display

1 Perimeter 4 Guest1 Perimeter 7 Guest2 Perimeter
2 Interior 5 Guest1 Interior 8 Guest2 Interior
3 Bedrooms 6 Guest1 Bedrooms 9 Guest2 Bedrooms

Account Number
ACCOUNT NO: 12345 Enter the account number to be sent to the receiver for this area. Choose an account number
compatible with the Communication Type selected in Communications. The default Account
Number is the one previously entered in Communications. This account number is used when
sending area messages and events to the central station.

Opening/Closing Reports
O/C RPTS NO YES This option allows an Opening/Closing report to be sent to the receiver when this area is
disarmed or armed.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

48
 Automatic Arming
AUTO ARM NO YES Select YES to allow this area to arm automatically according to permanent, temporary, or
extended schedules. If no schedules are programmed, the area auto arms every hour.
If closing check is selected as YES, the automatic arming function does not take place until
the expiration of a ten minute Closing Check delay. If the area has been disarmed outside
of any permanent or temporary schedule, the closing check sequence occurs one hour
after the area is disarmed.
At arming, bad zones are handled according to the option selected in section Bad Zones.
If a closing report is sent, the user number is indicated as SCH on the SCS-1R Receiver. NO
disables automatic arming for this area.
For ANSI/SIA CP-01 UL installations, Automatic Arming cannot be used for arming.

Bad Zones
BAD ZONES: BYP At the time of automatic arming, some zones in the area may not be in a normal condition.
This option allows you to program the panel response to these bad zones. This option does
not display if AUTO ARM is NO.
BYP - All bad zones are bypassed. A report of the bypass is sent to the receiver if Bypass
BYP FORC REF Reports is YES. The report indicates SCH as the user number.
FORC - All bad zones are force armed. Zones force armed in a bad condition are capable
of restoring and reporting an alarm if tripped. A forced zone report is transmitted if Bypass
Reports is YES. The report indicates SCH as the user number.
REF - The automatic arming is refused and no arming takes place. A No Closing report is
sent to the receiver regardless of the Closing Check selection.

Automatic Disarming
AUTO DIS NO YES NO disables automatic disarming by schedule for this area. When YES is selected, the
area automatically disarms according to permanent or temporary schedules. If an opening
report is sent to the receiver, the user number is indicated as SCH.

Burglary Bell Output

BURG BELL OUT: 0 Enter the output number (0 to 6, 500 to 999, G1 to G20, D01 to D16, or F1 to F20) that is
turned on any time a Burglary type zone is placed in alarm. The output is turned o when
you disarm any area and no other Burglary type zones are in alarm. The output can also be
turned o using the Alarm Silence option in the User Menu or by entering a user code with
the authority to silence alarms. The duration of this bell output follows the time entered
in the System Options > Bell Cuto Time option. The Burglary Bell Output entered here is
turned on for two seconds each time the system is armed.

Armed Output Number

ARMED OUTPUT: 0 Enter the output to turn on when this area is armed. If an exit delay is used for this area,
the Armed Output turns on at the start of the exit delay. The output is turned o when
this area is disarmed. The output cannot be turned on from the User Menu Outputs On/O
option.

Late Output Number

LATE OUTPUT: 0 Enter the output to turn on when this area is not armed by its scheduled time and Area
Late or Closing Time displays at a keypad and the keypad buzzer is on. The output is
turned o when the keypad buzzer is silenced by pressing any key. Default is 0.

Late Arm Delay

LATE/ARM DLY: 60 Enter 4 to 250 minutes to delay before automatic re-arming occurs after the area becomes
disarmed outside of schedules. See Closing Check. Default is 60 minutes.
The Late Arm Delay can be superseded by the Re Arm Delay setting of the User Prole
assigned to the user who disarmed the area.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

49
 Bank Safe & Vault (XR550INT with Network or Encryption Only)
BANK/SAF NO YES NO disables the Bank Safe & Vault feature for this area. Select YES to ensure that schedules
set for any area and the time of day cannot be changed while the area is armed.
Program schedules before arming: A Bank Safe & Vault area can only be disarmed during
scheduled times. If the area becomes armed before programming a schedule, the panel
must be reset before the area can be disarmed from a keypad or the Bank Safe & Vault
option in Area Information must be set to NO.
Zones assigned to Bank Safe & Vault areas cannot be bypassed or force armed. Do not
assign Bank Safe & Vault area to an Arming zone. Arming zones can disarm Bank Safe &
Vault areas outside of a schedule.

Common Area
COMMON NO YES Select YES to enable this area to operate as a common area. This area is armed when
the last area in the system is armed and is disarmed when the rst area in the system is
disarmed. You can have multiple common areas in each system. For the common area to
work properly, do not assign the common area to any user code.

Arm First Area

ARM FIRST NO YES Select YES to enable this area to operate as an Arm First area. This area is automatically
armed when any non-Arm First area assigned to the same keypad is armed but does not
disarm when other areas become disarmed. Assign areas to keypads using the Display
Areas option in Device Setup programming. You can have multiple Arm First areas in a
system and divide them among keypads if needed. If an Arm First area has faulted zones
that cannot be bypassed, arming stops and the areas are not armed. Correct the problem
with the Arm First area and then begin the arming process again. Default value is NO.
The Arm First automatic arming only occurs when arming from a keypad. Arming from a
zone, schedule, or remotely is not aected and Arm First areas do not automatically arm.

Dual Authority (XR550INT with Network or Encryption Only)

NO ARM DIS ALL Dual Authority requires two user codes to be entered at a system keypad to disarm and/
or arm this area. Dual Authority must be enabled per user in User Proles in order to use
this feature. When a user presents a user code to a keypad requesting to disarm or arm this
area, 2ND CODE displays and requires the entry of a dierent user code with at least the
same authority. The second user code must be entered within 30 seconds.
Select ARM to require two user code entries in order to arm this area. Select DIS (disarm)
to require two user code entries in order to disarm this area. Selecting the DIS option also
enables Dual Authority for Access Control. Select ALL to require two user code entries in
order to both arm and disarm this area, or select NO to disable Dual Authority for this area.
The default is NO.

Card Plus Pin (XR550INT with Network or Encryption Only)

CARD+PIN NO YES Card Plus Pin requires users to present both a credential and enter their 4-6 digit pin
number before the desired action for the specic areas will occur. If Card Plus Pin is set to
YES in an area and a prole, then the user is required to use card and pin to gain access. All
areas are defaulted to YES, while all proles are defaulted to NO.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

50
ZONE INFORMATION
Zone Information
ZONE INFORMATION Zone Information allows you to dene the operation of each protection zone used in the
system. All protection zones are programmed the same way.

Zone Number
ZONE NO: - Enter the number of the zone you intend to program. Available zone numbers are shown in
the table below.

Panel Programming Zone Number

Onboard 1-10
Keypad Bus Programming Zone Number
1 11-14
2 21-24
3 31-34
4 41-44
5 51-54
6 61-64
7 71-74
8 81-84
9 91-94
10 101-104
11 111-114
12 121-124
13 131-134
14 141-144
15 151-154
16 161-164
1100 Series Wireless Programming Zone Number
1144 Series Key Fob 400-449
LX-Bus Programming Zone Number
LX-Bus 500 500-599
LX-Bus 600 600-699
LX-Bus 700 700-799
LX-Bus 800 800-899
LX-Bus 900 900-999

Press CMD to enter a zone name.

Zone Name
* UNUSED * Zone names can have up to 32 alphanumeric characters. A name must be given to each
zone in the system. The name can display at the keypads during arming and disarming so
the user does not have to memorize zone numbers. A zone that is not part of the system
must be marked unused.
To add a zone name to the system, press any select key or area and then enter up to 32
characters for the new zone name. Press CMD to continue.
To mark a zone unused, delete the old name by pressing any select key or area, then press
CMD. The programmer automatically programs the name as * UNUSED *. If you have
already cleared Zone Information during Initialization, the zones is marked * UNUSED *.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

51
 Zone Type
ZONE TYPE: BLANK The panel contains 12 default zone types for use in conguring the system. These zone
types provide the most commonly selected functions for their applications. All zone types
except the Arming zone type can be customized by changing the options listed below.
The Zone Type denes the panel response to the zone being opened or shorted. This is
called the Alarm Action. There are up to 13 possible alarm action responses depending on
the zone type and any restrictions it may have. See the Zone Type chart in the Appendix.
When you assign a Zone Type to a zone, automatic alarm actions are made. There are 12
Zone Types to choose from.
To enter a new Zone Type, press any select key or area. The display lists all of the available
Zone Types four at a time.
Blank (--), Night (NT), Day (DY), or Exit (EX). Press CMD for additional zone types.
Fire (FI), Panic (PN), Emergency (EM), or Supervisory (SV). Press CMD for additional zone
types.
Auxiliary 1 (A1), Auxiliary 2 (A2), Fire Verify (FV), or Arming (keyswitch, AR). Press CMD for
additional zone types.
Carbon Monoxide (CO), Instant (IN), Doorbell (DB), or Final Exit (FX). Press CMD for
additional zone types.
Tamper (TP).

If you select Blank, Night, Day, Exit, Auxiliary 1, Auxiliary 2, Arming, Final Exit, or Tamper as
the Zone Type, the zone must be assigned to an active area. If you select Fire, Fire Verify,
Panic, Emergency, Supervisory, or CO as the Zone Type, it is a 24-hour zone that is always
armed and no area assignment is needed.

Area Assignment
AREA NO: - Enter the area number where the Night, Day, Exit, Auxiliary 1, Auxiliary 2, or Instant zone
is being assigned. For an Area system, area numbers 1-32 can be assigned. For a Home/
Sleep/Away with Guest system, area numbers 1-9 can be assigned.
In an All/Perimeter or Home/Sleep/Away system, the currently selected area, Perimeter,
AREA: PERIMETER Interior, Bedroom displays.
On an All/Perimeter system, select INT to program zones for the interior area and select
INT PERIM PERIM to program zones for the perimeter area.

On a Home/Sleep/Away system, select INT to program zones for the interior area, select
INT BDRM PERIM BDRM to program zones for the bedroom area, and select PERIM to program zones for the
perimeter area.

NO. EOLS Number of EOL

1 2 3 Select 1 to enable single EOL operation. This allows Normal/Open/Short conditions. Select
2 to enable dual EOL operation. This allows reporting and voltage thresholds on the zone
terminals to allow for a fourth zone state. Select 3 to enable triple EOL operation. This
allows the previous operation as well as a fth anti-masking zone state. Default is 2. For
additional information on anti-masking, refer to the Anti-Masking Feature section in the
Appendix.

Note: Triple EOL operation only works with Optex FLX Series Anti-Masking PIRs. All
other products use single or dual EOL operation.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

52
 Fire Bell Output
FIRE BELL OUT: 0 This output (1 to 6, 500 to 999, F1 to F20, G1 to G20, or D01 to D16) is turned on any time a
Fire, Fire Verify, or Supervisory zone is placed in alarm. The output is turned o by any of
the following actions:
• When the User Menu Alarm Silence function is performed.
• When a valid user code is entered to silence the bell.
• When the Silence key is pressed on the 630F Remote Fire Command Center.
• Using the Outputs On/O function in the User Menu.
• The expiration of the Bell Cuto time.

This output can be connected to a lamp, LED, or buzzer using the DMP Model 716 Output
Expansion Module.

Arming Zone Area Assignment

ARM/DIS AREAS In an Area or Home/Sleep/Away with Guest system, if the zone has been programmed as
an Arming Type (AR), enter the areas that the zone controls.

When the zone changes from normal to shorted, the programmed areas toggle between
the armed or disarmed condition using the Style programming below. When restored to
normal, no action occurs. When the zone is opened from a normal (disarmed) state, a
trouble is reported. When opened from a shorted (armed) state, an alarm is reported and
the zone is disabled until you disarm the area(s) from either a keypad, Virtual Keypad, or
Remote Link™ computer.

To visually indicate the armed state of the area(s), you can assign an Armed Output to
ARM AREAS: PERIM individual areas and use remote LEDs at the keyswitch. The LED turns on or o to indicate
to the user the armed state of the area(s).

Perimeter/All - Specify whether the arming zone arms just the Perimeter (PERIM) or the
PERIM ALL Perimeter and Interior areas (ALL) for All/Perimeter systems. When disarming, all areas are
disarmed.

Home/Sleep/Away - Specify whether the arming zone arms the Perimeter (HOME), the
HOME SLEEP AWAY Perimeter and Interior (SLEEP), or all three areas (AWAY). When disarming, all areas are
disarmed.
Arming Zone Operation
If any bad zones are present when the Arming zone is shorted, the LED delays lighting for
5 seconds. If during the 5-second delay the Arming zone is shorted again no arming takes
place. If 5 seconds expire without the zone shorting again or restoring to normal, the areas
arm and bad zones are force armed. To allow bad zones to be force armed, the Any Bypass
option must be set to YES. If Any Bypass option is set to NO, arming does not occur. See
the Area Information - Any Bypass section. A priority zone cannot be force armed.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

53
 Style
STYLE: This option species the style for the arming/disarming operation. The default style is TGL
(toggle). Press any select key or area to display the STYLE options. To view more style
options press CMD.
TGL (Toggle) - When the zone changes from disarmed to armed, the programmed areas
TGL ARM DIS STEP toggle between the armed or disarmed condition. When restored to disarmed, no action
occurs. When the zone is opened from a disarmed state, a trouble is reported. When
opened from a armed state, an alarm is reported and the zone is disabled until you disarm
the area(s) from either a keypad, Remote Link™, or Virtual Keypad.
ARM - When the zone is armed, the programmed areas are armed. When restored to
disarmed, no action occurs. When the zone is opened from a disarmed state, a trouble is
reported. When opened from a armed state, an alarm is reported.
DIS (Disarm) - When programmed as an Area system, a short will disarm the programmed
areas. When programmed as a ALL/PERIM or HOME/AWAY system, a short will disarm ALL
areas. When restored to normal, no action occurs. When the zone is opened from a normal
(disarmed) state, a trouble is reported.
STEP - When programmed as an AREA system, the Arming Type areas will arm and beep
the keypads once. When programmed as ALL/PERIM or HOME/AWAY, on the rst short
HOME will arm and beep the keypad once. On the second short, SLEEP will arm and beep
the keypads twice. On the third short, AWAY will arm and beep the keypad three times.
A normal condition will cause no action. An open condition will disarm the programmed
areas and beep the keypads for one second.
MNT (Maintain) - When the zone is shorted, the programmed areas are armed. When
MNT restored to normal, the programmed areas are disarmed and any alarm bells are silenced.
When the zone is opened from a normal (disarmed) state, a trouble is reported. If opened
from a shorted (armed) state, an alarm is reported and the zone is disabled until you
disarm the area(s) from either a keypad, Virtual keypad, or Remote Link™ computer.

Expander Serial Number

EXP SN: If using a zone expansion module, enter the 10 character serial number found on the
module. Press CMD to move to the next prompt.
Already In Use displays when the serial number is already programmed for another zone.
The programmed zone number displays.

Next Zone
NEXT ZN? NO YES Select YES to terminate zone programming. The display returns to Zone Number, allowing
you to enter a new zone number. Select NO to make alterations to the Alarm Action for a
zone.
To program zones for wireless operation, select NO at the NEXT ZONE - NO YES option.
The WIRELESS NO YES option displays. If the zone you are programming is intended for
wireless devices, select YES. Select NO to continue programming non-wireless zones in the
500 to 999 range.
• Zones 400 to 449 can be programmed for 1144 Series Key Fobs
• Zones 500 through 599 can be programmed for DMP 1100 Series Wireless on an
XR150INT Series panel
• Zones 500 through 999 can be programmed for DMP 1100 Series Wireless on an
XR550INT Series panel

ZONE INFORMATION Wireless

WIRELESS? NO YES Select YES to program this zone as a DMP wireless zone. You must program the wireless
House Code prior to adding DMP wireless zones to the system.
See House Code programming in System Options. Default is NO.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

54
TRANSMITTER Serial Number Entry
SERIAL#: XXXXXXXX Enter the eight-digit serial number found on the DMP wireless device.
Already In Use displays when the serial number is already programmed for another zone.
The programmed zone number displays.

TRANSMITTER Contact
CONTACT: XXXXXXXX Transmitter Contact displays if the serial number entered is for an 1101, 1103, or 1106
Universal Transmitter or 1114INT Wireless Four-Zone Expander. Press any select key or area
to select the contact.
TRANSMTR CONTACT Select INT to use the internal reed switch contacts. Select EXT to connect an external
INT EXT device to the 1101, 1103, or 1106 terminal block. Default is INT.
By allowing both of the transmitter contacts (INT and EXT) to be used at the same time,
two zones may be programmed from one transmitter. When using both contacts, you must
use consecutive zone numbers. The same serial number is used for both zones.
Contact Selection option displays when programming the 1114 Wireless Four-Zone
TRANSMTR CONTACT
Expander with four input contacts. The same serial number is used for all four contacts.
1 2 3 4
Select the contact number to program. When using the contacts, you must use consecutive
zone numbers. Default is Contact 1.
A tamper on the 1114 is transmitted as the zone number assigned to Contact 1.

Already In Use message displays when the Contact is already programmed for another
ALREADY IN USE
ZONE NUMBER: XXX zone. The programmed zone number displays.

When EXT is selected as the Contact type, external devices connected to the 1101, 1103 or
ZONE INFORMATION
NORM OPN NO YES 1106 terminal block, select NO to use normally closed (N/C) contacts. Select YES to use
normally open (N/O) contacts. Default is NO.

TRANSMITTER Supervision Time

SUPRVSN TIME: 240 Press any select key or area to select the supervision time required for the wireless zone.
Press CMD to accept the default time. Default is 240 minutes.
Refer to the Wireless Check-in and Supervision Time Denitions section of the Appendix
for supervision information.
Press the select key or area under the required number of minutes. The transmitter must
SELECT MINUTES:
check in at least once during this time or a missing condition is indicated for that zone.
0 3 60 240
1100 Series transmitters automatically checkin based on the supervision time selected
for the wireless zone, no additional programming is needed. If two zones share the same
transmitter, the last programmed supervision time is stored as the supervision time for
both zones. Zero (0) indicates an unsupervised transmitter.
The 3 minute supervision time is only available for zone types of Fire (FI), Fire Verify (FV),
Supervisory (SV), and Carbon Monoxide (CO).
When the panel is reset or a receiver is installed or powered down and powered up, the
supervision timer restarts for all wireless zones.

LED OPERATION LED Operation

NO YES Select YES to turn on an 1142 Hold-up transmitter LED during Panic or Emergency
operation. Select NO to turn the LED o during Panic or Emergency operation. The LED
always operates when the transmitter case is open and the tamper is faulted. Default is
YES.

DISARM DISABLE Disarm/Disable

NO YES Select YES to disable the Zone Tripped message from 1101/1102/1106 Universal Transmitters
(Version 108 of higher software), 1103 Universal Transmitters (Version 107 or higher
software) or 1122/1126/1127 PIRs during the disarmed period. When disarmed, the
transmitter or PIR only sends Supervision, Tamper, and Low Battery messages to extend
transmitter battery life. For transmitters, a Zone Tripped message is sent if the zone
remains tripped for 20 seconds. Select NO to always send Zone Tripped messages in
addition to Supervision, Tamper, and Low Battery. Default is YES.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

55
WIRELESS PIR PIR Pulse Count
PULSE COUNT: 4 Select the number of infrared pulses (2 or 4) the 1122, 1126, or 1127 PIR should sense before
sending a short message to the 1100XINT Series Receiver. Default is 4.

WIRELESS PIR PIR Sensitivity

SENSITIVITY: LOW Select the sensitivity setting for an 1122, 1126, or 1127 PIR. Selecting LOW sets the PIR to
operate at 75% sensitivity for installations in harsh environments. Selecting HIGH sets the
PIR to maximum sensitivity. Default is LOW.

WIRELESS PIR PET Pet Immunity

IMMUNITY: NO YES This option displays for the 1122 Wireless PIR Motion Detector. Select whether or not to
enable pet immunity. Selecting YES allows pet immunity for animals up to 55 pounds.
Default is NO.

Next Zone
NEXT ZONE NO YES Select YES to return to the ZONE NO: - option to program a new zone. Select NO to
display the Alarm Action option. Press CMD to continue.

Alarm Action
ALARM ACTION . . . . This option allows you to change any Zone Type standard denitions. When the Zone Type
is specied, the Alarm Action for that zone is stored in memory.

Disarmed Open
DISARMED OPEN Denes the action taken by the panel when the zone is opened while the area is disarmed.
There are three actions to dene: Report to transmit, Relay Output to activate, and Relay
Output action.
You must also make these selections for the Disarmed Short, Armed Open, and Armed
Short zone conditions. Press CMD to continue.

MSG: TROUBLE Report to Transmit

A T L - Press any select key or area to display the following report options: A, T, L, S, C, and -
(dash).
ALARM - Select Alarm (A) to send an alarm report to the receiver and activate the bell
output according to zone type. The zone name appears in the panel alarmed zones and
status lists.
TROUBLE - Select Trouble (T) to send a trouble report to the receiver. The zone name
appears in the panel alarmed zones and status lists.
UL requirements prevent the Alarm (A) and Trouble (T) action for Fire (FI), and Fire Verify
(FV) zone types from being changed.
LOCAL - When you select Local (L), an alarm report is NOT sent to the receiver. The bell
output activates and the zone name appears in the panel alarmed zones and status lists.
- (Dash) - When you select a – (dash), reports are NOT sent to the receiver. The bell output
does not activate and there is no display in the panel alarmed zones or status list. Only the
relay output selected in the next section operates.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

56
 DOOR PROPPED - Selecting D allows the ENTRY DLY 4 in the System Option section to
D S C begin to count without displaying on keypad. If the time expires and the zone has not
returned to normal, the keypad trouble buzzer starts and CLOSE THE DOOR appears on
the keypads programmed into the PREWARN ADDRESS section. The time programmed
into ENTRY DLY 4 begins to count down again internally. If the time expires a second time,
and the zone has not returned to normal, the output (if programmed in zone information)
triggers and a fault report is sent to the receiver and the zone name - OPEN message
displays on the keypads until a code is entered.
SENSOR RESET - When the zone state changes, the bell is silenced, a Sensor Reset is
performed and a Alarm Bell Silenced Message (S34) is sent.

CANCEL AMBUSH - Select C for the zone to cancel the Early Morning Ambush timer and
stop an Ambush message from being sent to the receiver. Faulting the zone takes the
place of a second user code being entered at the keypad and is only available for non-re
type zones. Area assignment for the zone does not aect this option. See Early Morning
Ambush in Area Information programming.

Output Number
OUTPUT NO: 0 You can specify any of the Relay Outputs on the panel to be activated by a zone condition
(1 to 6, 500 to 999 if Model 716 used, D01 to D16, G1 to G20). The output can be activated
regardless of the report to transmit or whether or not the zone is programmed as local. An
output activated by an armed zone is turned o when the zone area is disarmed by a user.
To enter an output number, press any select key or area followed by the output number.
Press CMD.

Output Action
OUTPUT: NONE Output Action allows you to assign an output action to the relay: Steady, Pulse, Momentary,
or Follow.
STEADY - The output is turned on and remains on until the area is disarmed, an output
STD PLS MOM FOLW cuto time expires, or the output is reset from the keypad menu.
PULSE - The output alternates one second on and one second o.
MOMENTARY - The output is turned on only once for one second.
FOLLOW - The output is turned on and remains on while the zone is in an o normal, or
bad condition. When the zone restores, the output is turned o.
For Day Zone types, when an output is turned on, a user code with silence authority can
turn the output o.

Disarmed Short, Armed Open, and Armed Short

After you make the three selections in the sections above, the display prompts for the same three selections for
Disarmed Short, Armed Open, and Armed Short conditions. If the zone is a 24-hour type, only the Armed Open and
Armed Short conditions will display. When you have programmed all of the zone conditions, the Swinger Bypass
selection then displays.

Swinger Bypass
SWGR BYP NO YES Selecting YES allows the zone to be swinger bypassed by the panel according to the
specications programmed in Swinger Bypass Trips and Reset Swinger Bypass. The Bypass
condition displays in the keypad Status List. Selecting NO disables swinger bypassing for
this zone.
If within one hour, a zone trips the total number of times as specied in Swinger Bypass
Trips, the panel bypasses it until the following conditions occur;
• The area in which the zone is assigned is disarmed
• The zone is manually reset through the Bypass Zones? keypad User Menu
function
• The zone remains normal for one hour and the Reset Swinger Bypass is YES.
If the zone trips fewer than the specied times within one hour, the bypass trip counter
returns to 0 (zero) and the process must be repeated.
A report of the swinger bypass is sent to the receiver if Bypass Reports is YES.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

57
 Prewarn Keypad Addresses
PREWARN KEYPADS: At the entry delay start, all keypad addresses selected here display ENTER CODE:-. If you
want the prewarn to sound at all 16 addresses, leave the default setting.
To delete an address, press the matching number on the keypad. To disable prewarning at
all keypads, press any select key or area to clear the addresses shown. Press CMD when the
address selection is complete.
The prewarn tone stops at the keypad where the rst user code digit is entered. If no keys
are pressed for ve seconds or an invalid user code is entered, the prewarn tone resumes
at that keypad.

Chime
CHIME: DOORBELL Option is only shown for Night, Exit, and Instant zones. Select either NONE, DB (doorbell),
ASC (ascend), or DSC (descend) to assign that tone to a zone. Default is DOORBELL for
Exit zones and NONE for Night zones.

Entry Delay
ENTRY DELAY: 1 Select the entry timer for this zone. Entry timers 1 to 4 are programmed in System Options.

Zone Retard Delay

RETARD NO YES When you select YES, the zone operates with the zone retard delay. The retard functions
only in zone short conditions. The zone must remain shorted for the full length of the
retard delay before the panel recognizes its condition. If you select NO, the zone operates
without a retard delay.
The zone must remain shorted for the full length of the retard delay before the panel
recognizes its condition. If you select NO, the zone operates without a retard delay.

Presignal Keypad Addresses

PRESGNL KEYPADS: You can enable any combination of keypad addresses to sound a presignal tone during the
time a zone is in retard delay. The presignal tone silences when the zone restores or the
retard delay expires. To enable a presignal address, press any select key or area followed
by the number of the keypad address. You can enable the presignal for all 16 keypad
addresses. To disable a presignal address press the matching number digit again. Press
CMD when the address selection is complete. The Presignal option is only displayed when
Retard is selected as YES.

Fast Response
FAST RSP NO YES Select YES to provide a zone response time of 167ms. Select NO to provide a normal zone
response time of 500ms. Zones 500 to 999 have a xed response time and do not display
this option.

Cross Zone
CRS ZONE NO YES Select YES to enable cross zoning for this zone. Cross zoning requires one or more armed
zones to fault within a programmed time before an alarm report is sent to the receiver.
When the rst cross zoned zone trips, the cross zone time specied in System Options
begins to count down. When a second cross zoned zone trips or the rst zone trips a
second time before the end of the count down, the bell action assigned to the zone
activates and the panel sends an alarm report for both zones.
If no other cross zoned zone trips before the cross zone time expires, the panel sends only
a zone fault report to the receiver.
Cross zoning is not compatible with all zone types: You can not enable cross zoning for
Fire verify zones or for any Fire zones that have Retard Delay enabled.

Priority
PRIORITY NO YES Select YES to provide additional protection for the premises by requiring this zone to be in
a normal condition before its assigned area can be armed.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

58
FIRE PANEL SLAVE Fire Panel Slave Input
INPUT: NO YES This option is available on Fire Zones (FI) only and allows a re zone the ability to provide
slave communication operation for a separate re alarm control panel. If YES, this zone will
transmit a restoral immediately when restored by the re panel being monitored. A sensor
reset is not required to generate the restoral message.
If NO, this zone will operate as a standard re type zone and a sensor reset is required
before the zone will return to normal. Default is NO.

Area Follower
FOLLOW AREA: 0 Allows Night, Day, Aux 1, or Aux 2 burglary zones to be delayed by following any exit or
entry delay that is currently running in the area that is specied. Default is 0.

ZONE REAL TIME Zone Real-Time Status

STATUS NO YES Selecting YES allows Real-Time Status reports, such as Door Open or Closed with zone
number, to be sent using PC Log reporting. Selecting NO disables Real-Time Status for this
zone. Default is NO.

TRAFFIC COUNT Trac Count

NO YES Trac Count is only displayed for NT, EX, and IN type zones. Select YES to provide
reporting to the receiver of the number of zone trips while in a disarmed state. The number
of trips will be included with the area closing message and reported to the central station
automation system. Trac Count data for the 10 lowest numbered zones with Trac Count
set to YES is also sent to the Virtual Keypad TM App if enabled at
dealer.securecomwireless.com. Default is NO.

Zone Audit Days

ZONE AUDIT DAYS: Enter the number of days (0 to 365) allowed to elapse without the zone being tripped
before a fault message is sent. The message is sent to the receiver(s) programmed to
receive Supervisory/Trouble Reports at 10:00 am following the expiration of the timer. Each
time the zone is tripped, the Zone Audit Days timer restarts and begins to countdown the
number of days programmed. After the countdown expires, a fault message is sent and the
Zone Audit Days timer restarts and begins to countdown the number of days programmed.
Available for all zone types except re and re verify. Enter 0 (zero) to disable this function.
Default is 0.

REPORT WITH ACCT Report with Account Number for Area

NO. FOR AREA: 0 This option is only available for 24-hour zone types (Fire, Fire Verify, Panic, Emergency, or
Supervisory).
Enter the area number (1-32) to assign as a 24-hour zone type. This option sends the
account number of the programmed area with messages. If the entered area number does
not exist or is not valid, the account number programmed in the Communication section
is sent. Select 0 (zero) to have the report sent with the account number programmed in
Communication. Default is 0.

LOCKDOWN: Lockdown
NO YES This option is available when programming a Panic type zone. Selecting YES triggers a
lockdown when a panic zone is tripped. Default is NO.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

59
1144INT SERIES KEY FOBS
For an 1144INT Series Key Fob set the House Code from 1 to 50. See House Code programming in System Options. Only
zones 400 to 449 can be programmed as 1144 Series Key Fob zones. Refer to the 1100INT Series Key Fob Programming
Sheet (LT-0706INT) supplied with the 1100XINT Series Wireless Receiver and the 1144INT Series Key Fob Install Guide
(LT-1449INT) as needed.
To operate arming and disarming properly, the Key Fob should be assigned to a User Number with appropriate area
assignments, however, the User Number does not have to exist at the time the Key Fob is programmed. The Key Fob
User Number can be added later by the User.
The following programming continues from the Zone Number section when zone 400-449 is selected.

KEY FOB USER Key Fob User Number

NUMBER: XXXX Enter the User Number (1-9999) used to identify the key fob user and their arming and
disarming authority. Default is blank.

USER XXXX User Not in Use displays when the User Number entered does not exist in User Code
NOT IN USE programming. The key fob can be added, but the user must eventually be added to cause
the key fob to operate.

TRANSMITTER Key Fob Serial Number

SERIAL#: XXXXXXXX Enter the eight-digit serial number found on the wireless device.

TRANSMITTER Key Fob Supervision Time

SUPRVSN TIME: 0 Press any select key or area to select the supervision time required for the key fob zone.
Press CMD to accept the default time. Default is 0 for key fobs.
Press the select key or area under the required number of minutes. The key fob must
SELECT MINUTES:
check in at least once during this time or a missing condition is indicated for that zone.
0 60 240
1144 Series key fobs automatically checkin based on the supervision time selected for the
wireless zone, no additional programming is needed. Zero (0) indicates an unsupervised
transmitter.
When the panel is reset or a receiver is installed or powered down and powered up, the
supervision timer restarts for all wireless zones.

NO. OF KEY FOB Number of Key Fob Buttons

BUTTONS: X Enter the number of buttons (1, 2, or 4) on the key fob being programmed.
If the key fob is a one-button model, programming continues at the Button Action section.
Default button assignment for one-button key fobs is a Panic Alarm (PN) with no output
assigned.

BUTTON: Key Fob Button Selection (Four Buttons)

TOP BTM LFT RGT If the key fob being programmed is a four-button model, press the select key or area under
the key fob button to program. The following list identies the default button assignments:
TOP Arming with no areas assigned
BTM Disarming with no areas assigned
LFT Panic Alarm (PN) with no output assigned
RGT Arming with Area 1 assigned

BUTTON: Key Fob Button Selection (Two Buttons)

TOP BTM If the key fob being programmed is a two-button model, press the select key or area under
the key fob button to program. The following list identies the default button assignments:
TOP Arming with no areas assigned
BTM Disarming with no areas assigned

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

60
BUTTON ACTION Button Action
YYY: XXXXXXXX Specify the Button Action for an individual key fob button. The default action for the
button selected is displayed. Press any select key or area to display the Button Action
options. To view more options press CMD.
yyy = the name of the button being programmed (TOP, BTM, LFT, RGT).
ARM (Arm) - Arms selected areas and force arms bad zones.
BUTTON ACTION
DIS (Disarm) - Disarms selected areas.
ARM DIS TGL STA
TGL (Toggle Arm) - Toggles arm/disarm for selected areas and force arms bad zones when
arming.
STA (Status) - Causes the key fob LED to indicate the arm/disarm status of the system.
PN (Panic) - Triggers a Panic zone type alarm with no restoral.
BUTTON ACTION
PN PN2 EM EM2 PN2 (Panic 2) - Triggers a Panic zone type alarm with no restoral when pressed
simultaneously with any other Panic 2 button. No action occurs when pressed alone.
EM (Emerg) - Triggers an Emergency zone type alarm with no restoral.
EM2 (Emerg 2) - Triggers an Emergency zone type alarm with no restoral when pressed
simultaneously with any other Emergency 2 button. No action occurs when pressed alone.
OUT (Output) - Causes an output to turn on steady, pulse, momentary, toggle, or o.
BUTTON ACTION
OUT RST UN RST (Sensor Reset) - Causes the panel to perform a standard Sensor Reset.
UN (Unused) - The button is not used and performs no action.

BUTTON Button Press Time

PRESS TIME: XXXXX Button Press Time species the amount of time (SHORT or LONG) the user must press the
button before the key fob sends a message to the wireless receiver. The default press time
displays. Press any select key or area to set the Button Press Time for Arm, Disarm, Toggle,
Status, Output, and Sensor Reset.
SHORT - Press the button for one-half (1/2) second to send the message to the wireless
PRESS TIME:
receiver.
SHORT LONG
LONG - Press the button for two (2) seconds to send the message to the wireless receiver.

Arm/Disarm Area Selection

ARM/DIS AREAS In an Area system or Home/Sleep/Away with Guest system, this species the areas to be
armed/disarmed by the Key Fob button being programmed. To select an area between 1
and 32, enter the area number using the keypad digit keys. Default is no areas enabled.
In order to arm or disarm selected areas, the Prole assigned to the User Number needs to
have the same area numbers selected. Any area may be selected at Arm/Disarm Areas but
only matching area numbers are armed or disarmed when the specic button is pressed.
When more areas are selected at Arm/Disarm Areas than are authorized in the User Prole,
in the future the user can be given access authority to additional areas through the User
Prole without requiring additional panel programming to select Arm/Disarm Areas.
In an All/Perimeter or Home/Sleep/Away system, this species the area to be armed by the
ARM AREAS: PERIM Key Fob button being programmed. For All/Perimeter systems, choose PERIM or ALL, for
Home/Sleep/Away or Home/Away systems, choose HOME, SLEEP, or AWAY.
Areas 3 and higher in an All/Perimeter system, and areas 4 and higher in a Home/Sleep/
Away system are not available for use.
After selecting the areas, for one-button key fobs the Zone No.: option displays. For two-
button or four-button key fobs, the Key Fob Button Selection option displays to program
additional buttons.

Output Number
OUTPUT NO: XXX You can specify any relay Output/Favorite to operate when OUT (Output), PN (Panic), PN2
(Panic 2), EM (Emergency), or EM2 (Emergency 2) is selected for a key fob Button Action
and the button is pressed. Valid range is 1 to 6, 500 to 999, D01 to D16, F1 to F20, or G1 to
G20. For an output turned on by a PN, PN2, EM, or EM2 button action, the output turns o
when any area is disarmed.
To enter an output/Favorite number, press any select key or area followed by the output/
Favorite number. Press CMD.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

61
OUTPUT ACTION: Output Action
yyy: XXXXXXXX Output Action allows you to dene the output action (STD, PLS, MOM, TGL, OFF) for the
selected output number. The default is Steady.
yyy = the name of the button being programmed (TOP, BTM, LFT, RGT).
xxxxxxxx = the currently dened output action.
STD (Steady) - The output is turned on and remains on.
OUTPUT ACTION?
PLS (Pulse) - The output alternates one second on and one second o.
STD PLS MOM TGL
Pulse is not available for key fob button output programmed D1 to D16 or G1 to G20.
MOM (Momentary) - The output is turned on only once for one second.
TGL (Toggle) - The output alternates between the on state and o state. Each button press
toggles the output state.
OUTPUT ACTION? OFF (O) - The output is turned o. If programmed, the output was turned on by some
OFF other means such as another button press, a zone action, or a schedule.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

62
STOP
Stop
STOP Save Programming
When any panel programming is changed, the stop routine must be run and “Saving
Program” must display on the keypad in order to save the programming changes.
At the STOP option, pressing any select key or area allows you to exit the Programmer
function of the panel. When selected, the panel performs an internal reset and exits the
programmer.
The STOP routine causes the following conditions to occur:
• All 1100 Series DMP Wireless transmitters are reset to NORMAL
• The panel Status List is cleared and all programming changes are saved
The STOP option does not disarm the system. Any new areas or zones that were added
during programming are not armed until the system is disarmed and armed again.
Missing LX-Bus™ Modules Displayed
The Programmer includes a feature following the STOP routine that displays the name of
any programmed LX-Bus module not currently connected to the panel.
Power Up
When the panel is powered up after an AC power failure, any zone transitions are not
recognized for 60 seconds. Normal zone processing resumes at the end of the 60 seconds.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

63
SET LOCKOUT CODE
Set Lockout Code
SET LOCKOUT CODE Pressing CMD at the STOP option displays SET LOCKOUT CODE. This allows you to
program a code that is then required to gain access to the panel internal Programmer
through the keypad. You can change this code at any time to any combination of numbers
from three to ve digits long. You do not need to enter leading zeros when using the
lockout code. Initializing the panel does not clear a Lockout Code. Lockout Codes can be
changed through Dealer Admin, Virtual Keypad, and Remote Link™.

Once you have changed the code, it is important to write it down somewhere and store
it in a safe place. Lost Lockout Codes require the panel to be sent back to DMP for repair.
You may cancel a Lockout Code by entering 00000 at the Set Lockout Code command.

Lockout Code restriction

Do not set a Lockout Code higher than 65535.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

64
FEATURE UPGRADE
Feature Upgrade
FEATURE UPGRADE In the Programming Menu, pressing CMD at the SET LOCKOUT CODE option displays
FEATURE UPGRADE. This allows you to enable additional features in the panel. Press any
select key or area to display the rst available feature. ENABLED or DISABLED displays
indicating whether this feature is currently used in this panel. Press CMD to display
additional feature(s).
Enter the factory-supplied feature key for the specic panel and press CMD. The feature
ENTER KEY
- specic to the key displays as ENABLED.
If the feature key entered is not accepted, the ENTER KEY option displays again.
Re-enter the feature key and press CMD.

ENCRYPTION Encryption
DISABLED Enable this feature to provide 128-bit or 256-bit AES data encryption. This feature upgrade
can only be enabled on an XR550INT panel with network. To verify encryption installation,
access System Status in the User Menu to verify the encryption status (OFF, ON). If the
status displays OFF, a Passphrase has not been entered in Network Options and data
transmissions are not encrypted. See Network Options to set up a Passphrase.

ALL NO YES OPTIN All No Yes Option

DISABLED This feature oers the ability to disable the ALL NO YES option at arming or disarming.
When this feature is enabled, the ALL NO YES option does not display at any system
keypad during arming or disarming. Each area assigned to the user prole is chosen to be
armed or disarmed independently.

SVC USER AUTH Service User Authentication

DISABLED This feature oers the ability to authenticate service personnel before allowing access
to panel programming or performing any user operations. When this feature is enabled
and a valid Service User code is entered for system operation or 6653 is entered for
programming, the Service Code entry option displays.
When the service person enters the Service Code, the panel authenticates the code with
the Service Code preprogrammed in the SCS-1R receiver, and access to panel programming
or the User Menu is granted. The Service Code can be used for system operation for
30 minutes before authenticating again. If the code entered is not validated, access to
programming or the User Menu using the Service User code is denied. The Service User
code is user number zero (0) and can only be created in the panel remotely.

32 DOOR ADD ON A 32 Door Add On A/ 32 Door Add On B

DISABLED This feature upgrade is only compatible with XR550INT Series panels operating with
Version 111 rmware or higher. Enable this feature to increase the door capacity for a
maximum of 64 or 96 doors by applying purchased feature keys. XR150INT Series control
panels are incompatible with this feature upgrade.
32 Door Add On A adds 32 more doors available on the AX-Bus for a total of 64 doors.
32 DOOR ADD ON B 32 Door Add On B adds another 32 doors to the AX-Bus for the maximum of 96 doors.
DISABLED Purchasing Feature Upgrades
If you would like to purchase a feature upgrade, the authorized purchasing agent for your
company may contact DMP Customer Service in writing via e-mail (CustomerService@
DMP.com) or call (866) 266-2826 from 8 AM to 5 PM CST. Include the upgrade feature(s)
to enable and the panel serial number(s) on the request. A separate feature key is issued
for each panel. The feature key only enables the requested feature on the specied panel.
The panel serial number can be located in several dierent ways:
• Printed on a label located on the right side of the PCB.
• Using Dealer Admin
• Using panel diagnostics. See the Appendix.
• Using Remote Link™ (Version 1.18 or greater).
• See the Remote Link™ User’s Guide (LT-0565)

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

65
EN 50131 GRADE
EN 50131 Grade
EN 50131 GRADE This option can be enabled for higher security Grade 3 Operation. Selecting 3 enables
Grade 3 operation. Selecting 0 enables standard DMP operation. Default is GRADE 0.

GRADE 0 The following operations are provided.

GRADE 0 3 Keypads
Blank Display Screen
When the keypad is not being used, the display will time out to a blank screen in 60
seconds. In addition, the Power and Armed LEDs are turned o.

Asterisk and Attention Display

Thinline™ Keypads:
When the display is blank and there are keypad messages in the Status List an asterisk (*)
will blink in the bottom right corner of the display screen. Press a top row select key and
enter a user code to display Status List. The asterisk will not display if any areas are armed.

Graphic Touchscreen Keypads:

When the display is blank and the system has placed keypad messages in the Attention
List, the keypad ashes ATTENTION to alert you to tap the screen and enter your user
code. The Attention List will not display if any areas are armed.

TRY AGAIN or INVALID CODE

If an invalid user code is entered 10 consecutive times, the keypad will be disabled for 90
seconds. INVALID CODE displays and an alert is sent to the Central Station.

User Menu
Service User? NO YES
After navigating past REQUEST SERVICE in the User Menu, SERVICE USER? NO YES is
displayed to determine the authority level of the service user to access PROG, DIAG and
User Menu.

When Yes is selected the Service User can add, edit and delete users. Service User can
enter panel programming. When EN50131 GRADE option is set to 3, any code assigned
prole 99 operates as a Level 3 user.

Only a Level 3 (Service User or user code with prole 99) user can arm the system if any of
the following conditions exist:

• Panel Tamper

• Zone or Wireless Device Tamper

• Bell Circuit Trouble

• Transmitter Missing

• Device Missing

• Communication path trouble

If any of those conditions exists, any other user that attempts to Arm or Disarm the system
will prompt Invalid Level to display on the keypad.

Closing Code
If AC POWER or BATTERY troubles exist in the Status List, a code is required to arm,
regardless of the Closing Code setting.

Default User Number

The Default User Number is changed to 0 with a user code of 99.

LED Indication
If there is more than 1 item other than time, weather, or ready status in the Status List, the
Status LED blinks at 1 sec o, 1 sec on.

System Restart Trouble Message

When a processor restart is logged in the event log, the Status List displays: SYS_RESET_-
TRBL_. This display does not clear until the service user performs a sensor reset.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

66
APPENDIX
FALSE ALARM REDUCTION
System Recently Armed Report
The System Recently Armed Report (S78) is sent to the receiver when a burglary zone goes into alarm within two
minutes of the system being armed.

ANTI-MASKING FEATURE
The triple EOL conguration is only designed to work with Optex FLX Series Anti-Masking PIRs. Although this device is
normally closed, it should be programmed in the following ways:

DisarmedArmed Short - The alarm contact is faulted on the PIR, and the normally closed contact is open.
DisarmedArmed Open - The trouble contact is faulted on the PIR, and the normally closed contact is open.
TamperAnti-Masking Detection - Both alarm and trouble contacts are faulted, and both contacts are open.
Tamper -The zone wires connected to the PIR are cut or shorted.

DIAGNOSTICS FUNCTION
The panel contains a Diagnostics function that allows you to test the communication integrity of the LX-Bus™, identify
individual zones, and also display the present electrical state of any zone. The Diagnostics function also allows you
to test the integrity of the cellular communication, and cellular signal.. To use Diagnostics, reset the panel, enter the
Diagnostics code 2313 (DIAG), and press CMD.

Test LX-Bus
This function allows you to test the ability of the panel to communicate with zone and output expander modules
connected to the LX-Bus circuits.

To continue, press any select key or area. The keypad displays LX-BUS:. Using the digit keys, enter the LX-Bus number, 1
to 5, to test that LX-Bus circuit. The keypad now displays ADDRESS: - . Enter a 2-digit LX-Bus device address and press
CMD. When testing LX-Bus devices, enter only the addresses to which the modules have been set. Press any select key
or area when TEST LX-BUS displays.

A device address is not the same as a zone number. If you are testing 714 or 715 Zone Expander Modules, which each
contain four zones, the device address is the rst zone number. When the panel polls a 714 on the LX-Bus, it recognizes
it as a four zone device and does not poll the remaining three zones. The 714 module internally polls the remaining zones
and transmits any status changes to the panel. This greatly reduces the amount of time it takes the panel to poll all LX-
Bus devices.

The keypad next displays TESTING . . . STOP during the device testing. At any time, you can select STOP to end polling.
The panel records the number of no responses from the device. If all polls are received back by the panel correctly, the
keypad displays 00000/65535 FAIL.

If one or more polling attempts fail, the keypad displays * * * * */65535 FAIL with the * representing the number of failed
polling attempts. A display of 65535/65535 FAIL indicates a problem with the interface card or its LX-Bus wiring such
as a bad or broken wire, harness not properly connected, or excessive noise or distance. It can also mean that a zone
number was entered that did not match a device address. Press the Back Arrow key to enter a new device address or
press CMD to exit the TEST LX-BUS.

Zone Finder
The second Diagnostic function is the Zone Finder. Press CMD to display ZONE FINDER. This function
allows you to identify individual zones on devices connected to the LX-Bus of an interface card, the panel, or any zones
on the keypad data bus. To use ZONE FINDER, press any select key or area. The display changes to FAULT ZONE. The
next zone on the system that changes from a normal to an open or shorted state is displayed as ZONE NO: * * *. To
continue, press the Back Arrow key.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

67
Zone State
Press CMD to display the third Diagnostic function: ZONE STATE. This function allows you to enter any zone number and
check its current electrical state (Normal, Open, or Shorted). Press any select key or area. The display changes to ZONE
NUMBER: _ . Enter in the zone number you want to check and press CMD. The panel displays the current state of the
zone as NRML (normal), OPEN, or SHORT.

LX-Bus Status
The fourth Diagnostic function is the LX-BUS STATUS. This function allows the panel to poll all devices connected to the
LX-Bus of an interface card and check for any Overlapped, Missing, or Extra addresses. Below is a description of each
status item:

Overlap - An overlap occurs when one device address is the same as any of the last three zones on another 714 or 715.
The overlap feature cannot determine when two devices have the same address.

Missing - A missing occurs when a zone between 500 and 999 has been programmed in ZONE INFORMATION and no
device with that zone address has been installed on the LX-Bus. To correct the problem, check your zone programming
and zone expansion module addressing.

Extra - A device is installed on the LX-Bus but none of its zones are programmed into the system.

MAC Address
Short for Media Access Control address. This hardware address uniquely identies each network node. Not to be
confused with an IP address, which is assignable. In the Diagnostics function, the MAC address is the panel on-board
network hardware address. Press any select key or area to display the panel MAC address. Press CMD to view the next
option.

Serial Number
This number is the network communicator serial number. Reference this number for communicator date-of-manufacture,
hardware version, etc. Press any select key or area to display the Serial Number. Press CMD to view the next option.

Loader Version
This display is for factory use only. Press any select key or area to display the factory Loader Version. Press CMD to view
the next option.

Current Flash
This option displays Flash 1 or Flash 2 indicating which physical ash chip the panel is currently using. Press select key or
area to display the current ash information. Press CMD to view the next option.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

68
Communication Status
This option tests the individual components of cellular or network communication. The displayed results are shown
below.

Cellular Results:

Successful Display Failure Display

MODEM OPERATING NO MODEM FOUND
IDENTIFIED NO SIM CARD
TOWER DETECTED NO TOWER
REGISTERED NOT REGISTERED

SIGNAL: ▐▐▐▐▐▐▐ This displays the cellular signal strength of the nearest tower for the SIM card carrier.
The ▐’s represent the signal strength 0-7. Select YES to continue through the remaining
CONTINUE? NO YES
component tests. Select NO to stop testing and return to the COMM STATUS option.

Successful Display Failure Display

CONNECT ERROR
CONNECTED
NOT ACTIVATED
COMM PATH GOOD NO ACK RECEIVED

Network Results:

Successful Display Failure Display

LINK OK LINK ERROR
DHCP OK DHCP ERROR
GATEWAY FOUND NO GATEWAY
DEST FOUND NO DESTINATION
COMM PATH GOOD NOT CONNECTED
NO ACK RECEIVED

Cellular Signal Strength (CELL SIGNAL)

-XX dBm This option provides a way to test the cellular signal strength of the nearest tower for
the SIM card carrier. Press any select key or area to display cell signal strength. The X’s
SIGNAL: ▐▐▐▐▐▐▐
represent the numerical value of the cell signal strength in -dBm. The ▐’s represent the
signal strength 0-7.

Wi-Fi Signal Strength (Wi-Fi SIGNAL)

SSID: HOMENET123 This option tests the signal strength of the selected SSID. Press any select key or area to
▐▐▐▐▐▐▐ display Wi-Fi signal strength. The▐’s represent the signal strength 0-7.

Wi-Fi Signal Strength

Number of Bars Indication
7
6 Good Signal (Excellent for consistent operation)
5
4
3 Average Signal (Expect consistent operation)
2
1 Weak Signal (Will not operate reliably. Relocate Wi-Fi
equipment or add a Wi-Fi extender for better reception.)
0 No Signal

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

69
PC Programming
This allows the user to Remote Program the panel through Remote Link and Dealer Admin, or by using a 399 cable
attached to LX500. When the select key or area is pressed, the panel displays PROGRAMMING... at the keypad for the
duration of the Remote Session. Once the session has ended, or if no Remote Link™ connection has been established after
one minute, the keypad displays RECONNECT LX BUS.

When using the 399 cable to program the panel, the connection type should be “Direct” and the baud rate set to 38400.
This connection may be used for all Remote Programming, including Remote Update.

Z-Wave Information
This option allows the installer to view the hardware and software level of the 738Z that is connected to the system.

Test Z-Wave Option

This feature allows the installer to test panel communication with Z-Wave devices. A successful test indicates a response
from a device. Press any select key or area to view the Z-Wave Device List.
Press CMD to advance through each Z-Wave device and press any select key or area to begin the test on the device
displayed.

The name of the device displays above the device number. The current number of successful communications followed
by the total number of attempts displays to the right of the device number. The test stops after 99 attempts.

Press CMD to view the nal number of successful communications.

Exiting the Diagnostics program

Press CMD until STOP displays. Press any select key or area. The keypad returns to the Status List display.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

70
USING THE 984 COMMAND FUNCTION
This feature allows connection to a service receiver, which is used primarily to bring a new account on-line and upload
panel programming completed in Remote Link™.

The function 984 + CMD can be entered at the keypad, and a remote options menu appears. This menu contains the
following options:

NUMBER: Enter a phone number into the keypad for the panel to dial. Enter any required prexes and area codes.

The panel dials each number as it is pressed. If you make a mistake, press the Back Arrow key. The panel stops dialing
and return to the Status List.

You can enter up to 32 characters for the phone number. Once you have entered 16 characters the LCD display is
full: Press CMD to enter the nal 16 characters. Program a pause by entering the letter P. Program CID message
communication by entering the letter T in the rst position. Cancel call waiting by entering *70P as the rst characters.
Press CMD after you enter the phone number.

The panel calls the receiver connected to Remote Link™ to download the new programming. Remote Link™ then traps
the panel.

The panel makes ten attempts to reach the receiver. While attempting to contact the receiver, if the panel needs to send
an alarm report, the panel stops dialing and uses the phone line to send its report.

TEST: The panel allows you to perform a Communication Status Test on each component of the panel’s cellular or
network communication paths. Press the select key or area under TEST to allow the panel to perform a Communication
Status Test. The display prompts the user for a user code to be entered. The user code must have the authority to
perform a System Test.
Upon entry of a Cell or Network path when prompted, the test runs and the results display on the keypad. See
Diagnostic Functions section for a description of the Communication Status results.
PICKUP: The panel picks up the phone line when Remote Link™ calls in. The phone must be ringing before selecting
PICKUP. After completing panel programming in Remote Link™, connect to the panel by selecting Panel > Connect. Refer
to the Remote Link™ User’s Guide (LT-0565), or Help File for complete information about connecting to panels.
While the panel displays in the status list and the telephone line at the panel rings, enter 984 and press CMD. The keypad
display changes to NBR TEST PICKUP. Press the select key or area under PICKUP to allow the panel to seize the line.
The panel immediately seizes the phone line and sends a carrier tone to the receiver. A verication process occurs and, if
successful, the panel grants remote access to its programming and Event Buer.

After the panel has seized the line, send the le from Remote Link™ by selecting Panel > Send. Remote Link™ then
uploads the new programming into the panel. You may also Request Events by selecting Panel > Request Events in
Remote Link™. The panel begins sending the rst event or access that occurred on or after the start date specied by
Remote Link™ and nishes by sending the last event or access that occurred on or before the end date specied by
Remote Link™. If necessary, a Request Events upload in progress can be cancelled.

KEYPAD DISPLAYS
When the PICKUP option is used, the keypad displays LINE SEIZED. This indicates that the panel has seized the line and
is executing its program. If the line cannot be accessed, or if the PICKUP option is used before all connect attempts are
made, the keypad displays SYSTEM BUSY.

USING THE WALK TEST

The panel provides a walk test feature that allows a single technician to test the protection devices connected to zones
on the system. Conduct the Walk Test within 30 minutes of resetting the panel. The Walk Test automatically ends if no
zones are tripped for 20 minutes. TEST IN PROGRESS displays at all keypads programmed with the same Display Areas
features. When ve minutes remain, TEST END WARNING displays. The Walk Test only tests zones assigned to the areas
programmed into the keypad in Display Areas. If any areas are armed the Walk Test does not start and SYSTEM ARMED
displays.
If the Panic Supervision option is enabled in SYSTEM OPTIONS, the panic button on any programmed key fob can be
tested during the Walk Test. When the panic button is pressed a verication message is sent by the receiver.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

71
 Walk Test
WALK TEST To conduct the Walk Test, reset the control panel by momentarily placing a jumper on
RESET. From the keypad, enter the code 8144.
The keypad displays WALK TEST for four seconds. If the system is monitored and the
communication type is DD or NET, the system sends a System Test Begin report to the
central station. After four seconds, the keypad displays the zone type choices for testing.

Zone Types
BG FI PN SV Select the zone type you want to test. An asterisk next to the zone type indicates the zone
type chosen for testing. Press the select key or area again to deselect the zone type. When
you have selected all the zone types you want for testing, press CMD to display the next
Walk Test option.
BG (Burglary zones) - Select BG to test hardwired burglary zones. Includes all NT, DY, EX,
A1, and A2 zones.
FI (Fire zones) - Select FI to test hardwired re zones. Includes all FI and FV zones.
PN (Panic zones) - Select PN to test hardwired panic zones. Includes all PN and EM zones.
SV (Supervisory zones) - Select SV to test hardwired supervisory zones. Includes all SV
zones.

During the Walk Test, trip each zone device or button on the system for 1 to 2 seconds.
You do NOT have to hold the zones for 2 seconds in normal mode for PN type zones. You
are only required to hold the panic during the Walk Test because the zone takes additional
time to report when the system is in test mode.

WLS (Wireless Check-in Test) - Select WLS to automatically test wireless transmitter
WLS PIR communications. Includes all wireless devices except key fobs and transmitters
programmed for a supervision time of 0 (zero).

PIR (Wireless PIR Walk Test) - The PIR Walk Test allows the installer to verify the 1122, 1126,
or 1127 operation. When enabled, the PIR LED ashes each time motion is detected for up
to 30 minutes. This is a local test only and no messages are sent to the Central Station.

Bell Action
BELL NO YES PULS This option selects the bell output action when a zone under test faults. This option allows
the panel bell, and/or burglary bell, and/or re bell to turn ON and then OFF each time a
zone is tripped (opened or shorted).
NO - Select NO for no bell output action during Walk Test.
YES - Select YES to turn on any bell output for 2 seconds during Walk Test.
PULS - Select PULS to turn on any bell output for 1/4 second during Walk Test. Any LX-Bus
device output turns on for 1.6 seconds due to the polling cycle.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

72
 Trip Counter For Walk Test
TRIPS: XXX END Once in the Walk Test, walk around and trip each protective device. Continue tripping
devices until the entire system is tested.
With each zone trip during the Walk Test:
• Keypad display increments each time a selected zone is opened or shorted
• The keypad buzzes for two seconds
• The panel sounds the alarm bells as programmed in Bell Action
• Each time a FI, FV, or SV zone trips, a Sensor Reset occurs.
If ENHANCED ZONE TEST is selected as YES:
A Verify message is sent at the time the zone trip occurs instead of at the end of the Walk
Test.
For FI, FV, SV, or CO zone types, the Verify message is sent at the initial trip.

For all other zone types, the Verify message is sent when the zone restores. This allows the
Central Station to count the number of devices per zone.

END - Select END to stop the Walk Test. When the Walk Test ends or a 20-minute time-out
expires, a nal Sensor Reset occurs. The System Test End message is sent to the receiver
along with Verify and Fail messages for each zone under test. Faulted zones then display
on the keypad.

IN PROGRESS XMIN Trip Counter For DMP Wireless Check-in Test (WLS)
CHECKIN: CC/TT END Displays the number of wireless zones that automatically communicate a supervisory
check-in message. The test will run for a total of 5 minutes. During the 5 minutes the
transmitters are being tested multiple times. At the end of the 5 minutes the results will be
displayed. A timer will be displayed at the keypad to indicate that the test is in progress.
In order for a transmitter to pass it must have checked in 3 or more times. The results will
display which transmitters have failed the test.
• The number of zones that check in. (CC in the example).
• The total number of wireless zones programmed for supervision that should check in.
(TT in the example).
END - Select END to stop the Wireless Test. When the test ends or a 5-minute time-out
CKIN:XXX/ZZZ END expires, normal wireless zone processing returns. If all transmitters check-in, both numbers
match within ve (5) minutes. If a transmitter has multiple zones (1101, 1114, etc.), all zones
are included in the counts. Failed wireless zones display on the keypad.

Test End Warning

TEST END WARNING When ve minutes remain on the 20 minute Walk Test timer, the keypad displays TEST
END WARNING. If no additional test zone trips occur, the test ends and a nal Sensor
Reset automatically occurs. The System Test End message is sent to the receiver along with
Verify and Fail messages for each zone under Walk Test. Faulted zones then display on the
keypad.
Key fobs do not send failure messages in order to prevent functioning key fobs that are not
present at the time of the test from being reported as MISSING.

ZONE: 10 -FAIL Failed Zones Display

SOUTH LOBBY For each zone that did not trip (failed), except key fobs, at least once during the Walk Test,
all keypads with matching Display Areas display the zone name and number and buzz for
one second. Any selected (*FI *PN *CO *SV) 24-hour zone that is faulted at the end of the
Walk Test displays a trouble condition for that zone regardless of
the message programmed for the open or short condition of the zone and a zone trouble is
sent to the receiver. Press CMD to display the next failed zone.
For the Wireless Check-in Test, failed wireless zones display only on the keypad. Zone
Verify/Fail reports are not sent to the central station receiver for the wireless check-in test.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

73
WIRELESS CHECK-IN AND SUPERVISION DEFINITIONS
DMP 1100 Series Supervision Time Explained
The supervision time programmed for DMP 1100 Series wireless is the number of minutes that must elapse before a
transmitter missing message is generated for a transmitter that is not sending its automatically generated supervision
message. The supervision time is programmable to 3, 60, 240 minutes. Selecting 0 (zero) disables supervision time.

KEYPAD SPEAKER OPERATION

When using LCD Keypads, the panel provides distinct speaker tones from the keypad for Fire, Burglary, Zone Monitor,
and Prewarn events. The list below details the conditions under which the speaker is turned on and o for each event.

Fire On - Fire zone alarm and Bell Output or Fire Bell Output is ON.
O - Alarm Silence.
Burglary On - Burglary zone alarm and Bell Output or Burglary Bell Output is ON.
O - Alarm Silence.
Zone Monitor On - One time only when a monitored zone is tripped.
O - After one tone.
CO On - CO zone alarm and Bell Output are ON.
O - Using Sensor Reset option while no additional CO type zones are in alarm.
Prewarn On - During Entry Delay.
O - When Entry Delay expires.

CROSS ZONING
Caution must be taken when cross zoning devices to ensure that the Cross Zone Time is long enough to allow an
intruder to trip both devices before it expires. A Cross Zone Time that is too short may allow an intruder to trip the
devices and allow only a zone fault report be sent to the central station.
When a Cross Zoned zone trips a FAULT report is sent to the SCS-1R or SCS-VR Receiver. When two Cross Zoned zones
trip within the Cross Zone Time, both zones send ALARM signals to the receiver.

USER PROFILES
A prole denes the authority of each user code in the system. Proles are programmed in the Keypad User Menu.
Several characteristics associated with each User Prole dene its authority within the system. To eectively program an
XR150INT/XR550INT Series system, you must understand the interrelationship between proles, devices, output groups,
and areas. Below is a brief explanation of the User Prole elements. For more information about user proles, refer to the
User Proles Record and the XR150INT/XR550INT Users Guide (LT-1278INT).

Proles cannot be changed via keypad in an All/Perimeter or Home/Sleep/Away system. Use the default proles 1
through 10.

Prole Number - Each prole may be assigned a unique number from 1 to 99.

Prole Name - Each prole may be assigned a 32-character name. The Prole Number is the default name.

Area Number - Each prole may be assigned specic areas of the system for arming and disarming. When creating
proles 1 to 98, NO areas are assigned by default. The default for prole 99 is ALL areas assigned. Prole 99 is
preprogrammed in the system at the factory.

Access Area Number - Each prole may be assigned door access area assignments. Default for prole 1 to 98 is NO areas
assigned. Default for prole 99 is ALL areas assigned. Prole 99 is preprogrammed at the factory.

Output Group Assignment - Each prole may be assigned an output group number from 1 to 10. Default for prole 1 to
98 is NO output group assigned. Default for prole 99 is output group 10. Your system may by programmed to turn on
an output group at certain keypads when door access occurs.

User Menu Assignments - Each user prole may have any of the menus assigned to it as shown in the following
User Prole Record. The User Prole Record lists the user menu prole assignments and the system functions users
are allowed to access based on the prole numbers assigned to their codes. Always make sure that at least one
administrator in your system has a prole with all authorities and areas.

First Access/Second Access - Each prole may be assigned two schedules to allow or restrict access and disarming
times.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

74
Inactive User Code Audit - This option allows you to choose the number of days a user code can remain unused before
the panel sends an Inactive User Code message to the receiver and changes the user code to inactive. The range is
0-425 days. The default is 0. This feature is only available for XR550INT Series panels.

USER PROFILES RECORD

This User Proles Record can be used as a tool when programming Devices, Proles, Areas, and Output Groups. Because
these programming options are interrelated, use this sheet to plan the system before you begin the installation and
programming process.

Door Lock/Unlock

Extend Schedules

Audit Days 0-425

Seventh Access, 1-99

Easy Arm/Disarm
Second Access, 1-99
Temp User Code
Service Request

Technician User
Fourth Access, 1-99

Eighth Access, 1-99

Outputs On/Of

Third Access, 1-99

Output Groups

Sixth Access, 1-99

Dual Authority
Display Events

Fith Access, 1-99

First Access, 1-99
System Status

Anti-passback
Alarm Silence

Sec Language
Re Arm Delay
Zone Monitor

Card Plus Pin

Bypass Zones

Inactive User
Sensor Reset
Access Areas

User Proles
Door Access
Arm/Disarm

System Test
Armed Area

Zone Status

Wi-Fi Setup
User Codes
Lockdown

Schedules

Fire Drill
Prole #

Disarm

Prole
Areas

Time
Arm

Name

ZONE TYPE DESCRIPTIONS

This section describes applications for the default Keypad and LX-Bus zone types in Zone Information programming.

-- (Blank Zone)
Customizable zone type. By default, no actions are programmed to occur with Blank Zone. A zone name must be
entered to use this zone type: This zone type is not the same as an *UNUSED* zone.

NT (Night Zone)
Controlled instant zone used for perimeter doors and windows and interior devices such as PIRs and Glassbreak
detectors.

DY (Day zone)
Used for emergency doors or re doors to sound the keypad buzzer and display the zone name when the zone is
faulted. Day zones also send alarm reports to the receiver during the system armed periods.

EX (Exit zone)
Initiates the entry delay timer when its assigned area is fully armed. Also, can initiate an exit delay timer to allow a user
to exit an area after the arming process starts.

FI (Fire zone)
Used for any type of powered or mechanical re detection device. Typical applications are for smoke detectors, sprinkler
owswitches, manual pull stations, and beam detectors. Retard, cross zoning, and presignal options are available for the
Fire zone type.

PN (Panic zone)
Used for connecting to mechanical devices that allow a user to signal an emergency alarm. Panic zones can provide
either a silent or audible alarm with or without reporting to a central station receiver.

EM (Emergency zone)
These are used for reporting medical or other non-panic emergencies to the central station receiver.

SV (Supervisory zone)
Used to provide 24-hour zone supervision to devices associated with re systems. Typical applications are tamper
switches on Post Indicator Valves (PIVs), gate valves, and low and high temperature gauges.

A1 and A2 (Auxiliary 1 and Auxiliary 2)

These zones are similar to a Night zone and are typically used to protect restricted areas within a protected premises.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

75
FV (Fire Verify zone)
Used primarily for smoke detector circuits to verify the existence of an actual re condition. When a Fire Verify zone
initiates an alarm, the panel performs a Fire Reset. If any Fire Verify zone initiates an alarm within 120 seconds after the
reset, an alarm is indicated. If an alarm is initiated after 120 seconds, the cycle repeats.

AR (Arming zone)
This zone allows you to connect a keyswitch to a zone and use it to arm and disarm one or more areas.

CO (Carbon Monoxide)
This output turns on any time a Carbon Monoxide Zone (CO) is placed in alarm. The output is turned o using Sensor
Reset option while no additional CO type zones are in alarm.

IN (Instant)
This provides a zone that does not follow entry or exit zones. Choose Instant if you need a zone that will not follow Entry
or Exit delay.

DB (Doorbell)
This zone type is intended for use for zones that are assigned to doorbells.

FX (Final Exit)
This zone type is used to identify a zone that must be tripped before the system will arm.

TP (Tamper)
This zone type is used to identify zones that are being used for enclosure tamper switches.

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

76
COMMON KEYPAD MESSAGES
There are several common keypad messages that the keypad displays to inform the technician and end-user. The
common messages are described below. Possible solutions are also provided.

Message Meaning Possible Solutions

Change the user access areas if access to
The user has attempted a door access for an
INVALID AREA the area is needed. If access is not needed,
area they are not assigned.
the user cannot enter the area.
The user code you entered is not recognized
INVALID CODE Check the user code and try again.
by the system.

A user attempted a function that is outside of

INVALID PROFILE Check the user prole settings.
the assigned prole.

A user code assigned to a specic schedule

INVALID TIME See Schedules and User Codes.
has entered outside of the valid schedule.
The area you are attempting to disarm or A second and dierent user code must be
ENTER 2ND CODE
access is a Two Man Area. entered.
Users still on the premise should arm the
The scheduled has expired but the area is not
CLOSING TIME system or extend the schedule to a later
armed.
time.
Users still on the premise should arm the
The system was not armed at its scheduled
LATE TO CLOSE system or extend the schedule to a later
closing time.
time.
The user must exit the area through the
A user assigned the anti-passback option has
proper door. If not possible, your system
FAILED TO EXIT attempted to re-enter an area from which they
administrator should select the Forgive
did not exit properly.
option in the User Codes menu.
AC TROUBLE The system AC is low or missing. Check that all AC connections are good.
Check that the battery connections are
BATTERY TROUBLE The System battery is either low or missing.
good and the battery is still good.
PHONE LINE 1 There is trouble with the phone line
Plug in the phone line.
TROUBLE supervision.
Make sure the RESET jumper is removed
from the panel. Make sure there is not a
SYSTEM TROUBLE or There is a problem with one or more short or open condition on the green data
SERVICE REQUIRED components in the system. wire to the keypad. You may also need to
check that all of the keypads and expansion
modules on the bus are good.
Wait a few moments for the system to
complete the task. Make sure the RESET
The system is performing another task with a
SYSTEM BUSY jumper is not on the panel. If the message
higher priority.
displays for a long period of time, the
processor could be locked up.
There is not a supervised device on the bus. Program a device to be supervised.
4-WIRE BUS There is low voltage or an open yellow wire. Make sure all wires are connected.
TROUBLE
Program one of the devices to a unique
Two devices share the same address.
address.
Verify your communication type, account
The panel has attempted to communicate
number, and phone number. Make sure the
TRANSMIT FAIL with the central station 10 times and has not
telephone line is connected and working
succeeded.
properly.
NON-POLLED The device is not set to DOOR, KEYPAD or Program the device as DOOR, KEYPAD or
ADDRESS FIRE in Device Setup during programming. FIRE in Device Setup.
ENTER CODE (to A lockout code has been programmed for the
Enter the lockout code.
enter Programming) panel.
The panel is unable to communicate with the Verify the receiver is properly connected to
wireless receiver. the panel. Verify the correct House Code is
WIRELESS TROUBLE
programmed in System Options. Satisfy the
The wireless receiver’s tamper may be faulted. front and/or rear tamper.

XR150INT/XR550INT Series Programming Guide Digital Monitoring Products

77
AREA ACCOUNT NUMBER MESSAGES
XR150INT/XR550INT systems send an area account number instead of the system account number with the following
panel messages/events based on the area assigned to the zone that initiated the alarm:
• WARNING: Alarm Bell Silenced (S34)
• Abort Signal Received (S45)
• Cancel Signal Received (S49)
• ALERT: System Recently Armed (S78)
• ALERT: Exit Error (S80)
• ALARM: Verify Signal Received (S96) (not currently sent on area arming systems)
• The panel has always sent the area account number for the following messages:
• Zone event messages for all non-24 hour zones assigned to an area
• Arming
• Disarming

The panel sends the following messages using the area account number based on the lowest area number in Display
Areas programming from the keypad being used:
• User Code Add/Change/Delete
• Door Access/Denied
• User 1 Ambush and Early Morning Ambush
• System Test Begin/End
• Unauthorized Entry
• Service Code and Service Request

The panel sends the following messages using the area account number based on the area number:
• Late to Arm for area schedules

Digital Monitoring Products XR150INT/XR550INT Series Programming Guide

78
SPECIFICATIONS
Power Supply Type A
Security Grade 3
EN 50131-1
Notication Requirements Grade 3, Option A, B, C
Environmental Class II
Operating Temperature 0°C - 49°C
Relative Humidity 80%
Weight 6.1 kg
Dimensions 26 cm W x 14 cm H
Max Ripple Voltage 50 mV

INTERNATIONAL CERTIFICATIONS
INTERTEK (ETL) LISTED
EN 50130-4:2011+A1:2014 Alarm systems. Electromagnetic compatibility. Product amily
standard: Immunity requirements or components o re,
intruder, hold up, CCTV, access control and social alarm
systems.
EN 50130-5:2011 Alarm systems. Environmental test methods.
EN 50131-1:2006+A1:2009 Alarm systems. Intrusion and hold-up systems. System
requirements.
EN 50131-3:2009 Alarm systems. Intrusion and hold-up systems. Control and
indicating equipment.
EN 50131-5-3:2005+A1:2008 Alarm systems. Intrusion systems. Requirements or
interconnections equipment using radio requency techniques.
EN 50131-6:2008 Alarm systems. Intrusion systems. Power supplies.
EN 50136-1:2012 Alarm systems. Alarm transmission systems and equipment.
General requirements or alarm transmission systems.
EN 50136-2:2013 Alarm systems. Alarm transmission systems and equipment.
Requirements or Supervised Premises Transceiver (SPT).
EN 61000-3-2:2006+A1+A2 Electromagnetic compatibility (EMC) — Part 3 – 2: Limits —
Limits or harmonic current emissions.
EN 61000-3-3:2013 Electromagnetic compatibility (EMC) - Part 3-3: Limits-
Limitation o voltage changes, voltage fuctuations and ficker
in public low-voltage supply systems, or equipment with
rated current ≤16 A per phase and not subject to conditional
connection.
EN 61000-6-4:2007 Emission standard or industrial environments.

Designed, engineered, and INTRUSION • FIRE • ACCESS • NETWORKS

manufactured in Springeld, MO 2500 North Partnership Boulevard
using U.S. and global components. Springeld, Missouri 65803-8877
LT-1232 1.01 24301 800.641.4282 | DMP.com
© 2024