Scribd
Upload
43 views7 pages

Experiment 10

Uploaded by

Jyotishankar Sahoo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
43 views7 pages

Experiment 10

Uploaded by

Jyotishankar Sahoo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

EXPERIMENT-10

NIRMAL GANGODA (U22EC104)

Aim: Design a Butterworth low pass analog filter to satisfy the following
requirements pass-band cutoff=40Hz, stop-band cutoff=150Hz, pass-band ripple
Rp=1dB and stop-band ripple Rs=60dB. Plot the magnitude and phase frequency
response of the filter

Apparatus:

MATLAB Software

Theory:

A Butterworth low-pass filter is designed to allow signals with a frequency lower


than a specified cutoff frequency to pass through while attenuating higher
frequencies. This type of filter is particularly valued for its maximally flat
frequency response in the pass-band, meaning it avoids ripples, providing a smooth
output signal.

Cutoff Frequency (ωc): This is the frequency at which the output power drops
to half its maximum value (or -3 dB point). Frequencies below this value are
allowed to pass with minimal attenuation.

Filter Order (n): The order of the filter determines the steepness of the roll-off
beyond the cutoff frequency. A higher order results in a sharper transition from
the pass-band to the stop-band, enhancing attenuation of unwanted high
frequencies.

Pass-band Ripple (Rp): For a Butterworth filter, the pass-band is characterized


by no ripples, as it is designed to provide a flat response up to the cutoff
frequency.

Stop-band Ripple (Rs): This indicates the allowable ripple in the stop-band.
For Butterworth filters, while there is no ripple in the pass-band, the stop-band
is defined by the level of attenuation.
Filter Design

To design a Butterworth low-pass filter:

1. Determine the Filter Order (n): The required order can be calculated using
the formula:

This formula ensures that the filter meets the specified stop-band and pass-
band requirements.

2. Cutoff Frequency (ωc): The cutoff frequency is typically set to the pass-
band cutoff frequency.
3. Transfer Function: The transfer function of an n-order Butterworth filter is
given by:

This function describes how the filter modifies the input signal.

CODE:

1)LOW PASS FILTER


clc;
clear all;
close all;

fs=1000;
wp=40;
ws=150;
Rp=1;
Rs=60;

w1= 2*wp/fs;
w2= 2*ws/fs;

[N,wn]=buttord(w1,w2,Rp,Rs);
display(N);
[b,a]=butter(N,wn,'low');
[h,w]=freqz(b,a,128,1000);
plot(w/pi,abs(h));
display(wn);
title('Butterworth HPF(N=original(6)');
xlabel('Normalised frequency');
ylabel('Amplitude;');
grid on;
axis([0 120 0 1.2]);

FOR DIFFERENT N:
clc;
clear all;
close all;

wp=40/1000;
ws=150/1000;

rp=1;
rs=60;

[N,wn]=buttord(wp,ws,rp,rs);

n=2;
[b1,a1]=butter(n,wn,'low');
[h1,w1]=freqz(b1,a1,128,1000);

n=4;
[b2,a2]=butter(n,wn,'low');
[h2,w2]=freqz(b2,a2,128,1000);

n=6;
[b3,a3]=butter(n,wn,'low');
[h3,w3]=freqz(b3,a3,128,1000);

n=8;
[b4,a4]=butter(n,wn,'low');
[h4,w4]=freqz(b4,a4,128,1000);

n=10;
[b5,a5]=butter(n,wn,'low');
[h5,w5]=freqz(b5,a5,128,1000);

plot(w1/pi,abs(h1),w2/pi,abs(h2),w3/pi,abs(h3),w4/pi,abs(h4),w5/pi,abs(h5));
legend('N=2','N=4','N=6','N=8','N=10');
title('Butterworth LPF');
xlabel('Normalised frequency');
ylabel('Amplitude');
grid on;
axis([0 50 0 1.2]);

2)HIGH PASS:
clc;
clear all;
close all;

fs=1000;
wp=40;
ws=150;
Rp=1;
Rs=60;

w1= 2*wp/fs;
w2= 2*ws/fs;

[N,wn]=buttord(w1,w2,Rp,Rs);
display(N);
[b,a]=butter(N,wn,'high');
[h,w]=freqz(b,a,128,1000);
plot(w/pi,abs(h));
display(wn);
title('Butterworth HPF(N=original(6)');
xlabel('Normalised frequency');
ylabel('Amplitude;');
grid on;
axis([0 120 0 1.2]);

FOR DIFFERENT N:
clc;
clear all;
close all;
wp=40/1000;
ws=150/1000;

rp=1;
rs=60;

[N,wn]=buttord(wp,ws,rp,rs);

n=2;
[b1,a1]=butter(n,wn,'low');
[h1,w1]=freqz(b1,a1,128,1000);

n=4;
[b2,a2]=butter(n,wn,'low');
[h2,w2]=freqz(b2,a2,128,1000);

n=6;
[b3,a3]=butter(n,wn,'low');
[h3,w3]=freqz(b3,a3,128,1000);

n=8;
[b4,a4]=butter(n,wn,'low');
[h4,w4]=freqz(b4,a4,128,1000);

n=10;
[b5,a5]=butter(n,wn,'low');
[h5,w5]=freqz(b5,a5,128,1000);

plot(w1/pi,abs(h1),w2/pi,abs(h2),w3/pi,abs(h3),w4/pi,abs(h4),w5/pi,abs(h5));
legend('N=2','N=4','N=6','N=8','N=10');
title('Butterworth LPF');
xlabel('Normalised frequency');
ylabel('Amplitude');
grid on;
axis([0 50 0 1.2]);
Output graphs:

1)Low Pass

i) N=6; ii) N={2,4,6,8,10};

2)High Pass
i) N=6; ii) N={2,4,6,8,10};

Conclusion:

In this experiment we learned how to design butterworth low pass filter and high
pass filter for given passband cutoff frequency and stopband cutoff frequency also
learned to plot the magnitude and phase response of the filters

You might also like