SPC-001 (EN/ DIN Food A304)

Pipe class:
Tubing material: 1.4307 (A304L)
Fitting material: 1.4307 or 1.4301 (A304L or A304) or 1.4404 (A316L) / supplier standard
Design: 10 barg @ 80°C
Pressure rating: 10 barg
Temperature range: 0°C / +80°C
Corrosion allowance: 0 mm
PED Category: Art.4, par.3 SEP (sound engineering practice)

Tubing/ piping

Tube EN standard: EN 10357-Series A (DIN 11850 Reihe 2)

Material: A304L (1.4307)
Nominal: Outside diameter (mm) Wall Thickness (mm)
DN

DN10 13 1.5
DN15 19 1.5
DN20 23 1.5
DN25 29 1.5
DN32 35 1.5
DN40 41 1.5
DN50 53 1.5
EN10357-series
DN65 70 1.5
DN80 85 1.5
DN100 104 2
DN125 129 2
DN150 154 2
DN200 204 2
DN250 254 2

Connections
Tri-clamp norm: DIN 32676-Reihe 2
Material: Supplier standard / 1.4307 (A304L) or 1.4404 (A316L)
Pressure/size range: DN10-DN50 =16 bar / DN65-DN200 =10 bar @ -10°*/150°C
Ferrule: DIN 32676-Reihe 2
Closure type SH: Clamp-ring - double pin
Gasket material: EPDM (temp. range -30°C/ 130°C) *

Union norm: DIN 11851 Form S

Material: Supplier standard / 1.4307 (A304L) or 1.4404 (A316L)
Pressure/size range: DN10-DN40 = 40 bar / DN50-DN100 = 25 bar / DN125-150 = 16bar @ -10°*/140°C
Welding male: DIN 11851 Form SC
Liner: DIN 11851 Form SD
Nut: DIN 11851 Form F
Gasket: DIN 11851 Form G
Gasket material: EPDM (temp. range -30°C/ 130°C) *
Flange norm: EN 1092-1 **
Material: 1.4301/1.4307 (A304(L))
Pressure/size range: PN10= 10bar @ RT= -10°/ 50°C _ 8,6 bar @ 100°C (in between values to be calculated)
Loose flange: EN1092-1 type 02 DN10-DN40 = PN40, DN50-DN150=PN16, DN200-DN250=PN10
Lapped pipe end: EN1092-1 type 33_Collar thickness (F) DN10-DN250= 2 mm *** DN10-DN250=PN10
Gasket: EN1514.1 type IBC
Gasket material: Novapress 850 *
Bolting: Hexagonal A2/ A4-70 ; metrical ISO 4014 (DIN931) ****
Nuts: Hexagonal A2/ A4-70. ; metrical ISO 4032 (DIN934)

Fittings
Weld fittings norm: EN10374 Series A (DIN 11852)
Material: 1.4307 or 1.4301 (A304L or A304)

Pressure/size range: DN10-DN50 = 25 bar / DN65-DN100 = 16 bar / DN125-200 = 10 bar/ DN250 = 8 bar (calculated @ 20°, see sta
Elbow short 45°/90° EN10374 Series A-BS-90 (45) *****
Elbow long 45°/90° EN10374 Series A-BL-90 (45) *****

Pressure/size range: DN10-DN50 = 25 bar / DN65-DN80 = 16 bar / DN100 = 12 bar / DN125 = 10 bar / DN150 = 8 bar (calculated @
T-piece short EN10374 Series A TS
T-piece long a/ EN10374 Series A TL
T-piece red. short EN10374 Series A TRS
T-piece red. long a/ EN10374 Series A TRL

Pressure/size range: DN10-DN50 = 25 bar / DN65-DN100 = 16 bar / DN125-DN150 = 12 bar / DN200-DN250 = 10 bar (calculated @
Reducer concentric short b/ EN10374 Series A RCS
Reducer eccentric Short b/ EN10374 Series A RES
Remarks; - Fittings and connectors allowable pressure/ temperature ranges taken from applicable DIN norm and/ or EN standard
- EN standards supersede DIN standards when available and/or mentioned in above SPC
* - Synthetic/ rubber gaskets tracebility according to EC1935/2004
** - Flange type not preffered (not hygienic), only to use in case of supplier standard connections
*** - Lapped pipe end (collar) thickness approximately tubing thickness for inside flush piping connections. PN10 design pressure r
**** - Length bolting minimal 2 windings through the nut after torque
***** - Short version = manually welding _ long version = orbital (automatic) welding
Notes;
a/ See cut to size dimensional table 1 if T-piece reduced is used for valve/ instrumentation welding connections (to achieve minim
leading
 SPC-002 (EN/ DIN Food A316)

Pipe class:
Tubing material: 1.4404 (A316L)
Fitting material: 1.4404 (A316L or >)
Design: 10 barg @ 80°C
Pressure rating: 10 barg
Temperature range: 0°C / +80°C
Corrosion allowance: 0 mm
PED category: Art.4, par.3 SEP (sound engineering practice)

Tubing/ piping
Tube EN standard: EN 10357-Series A (DIN11850 Reihe 2)
Material: 1.4404 (A316L)
Nominal: Outside diameter (mm) Wall Thickness (mm) Norm/standard
DN
DN10 13 1.5
DN15 19 1.5
DN20
DN25
DN32
DN40
DN50
-serie
DN65
DN80
DN100
DN125
DN150
DN200
DN250

Connections
Tri-clamp norm:
Material: Supplier standard / A316L (1.4404)
Pressure/size range: DN10-DN50 =16 bar / DN65-DN200 =10 bar @ -10°*/150°C
Ferrule: DIN 32676-Reihe 2
Closure type SH: Clamp-ring - double pin
Gasket material: EPDM (temp. range -30°C/ 130°C) *

Union norm: DIN 11851 Form S

Material: 1.4404 (A316L)
Pressure/size range: DN10-DN40 = 40 bar / DN50-DN100 = 25 bar / DN125-150 = 16bar @ -10°*/140°C
Welding male: DIN 11851 Form SC
Liner: DIN 11851 Form SD
Nut: DIN 11851 Form F
Gasket: DIN 11851 Form G
Gasket material: EPDM (temp. range -30°C/ 130°C) *

Flange norm: EN 1092-1 **

Material: 1.4401/1.4404 (A316(L))
Pressure/size range: PN10= 10bar @ RT= -10°/ 50°C _ 9,4 bar @ 100°C (in between values to be calculated)
Loose flange: EN1092-1 type 02 DN10-DN40 = PN40, DN50-DN150=PN16, DN200-DN250=PN10
Lapped pipe end: EN1092-1 type 33_Collar thickness (F) DN10-DN250= 2 mm *** DN10-DN250=PN10
Gasket: EN1514.1 type IBC
Gasket material: Novapress 850 *
Bolting: Hexagonal A4-70 ; metrical ISO 4014 (DIN931)***
Nuts: Hexagonal A4-70. ; metrical ISO 4032 (DIN934)

Fittings
Weld fittings norm: a/ EN10374 Series A (DIN 11852)
Material: 1.4404 (A316L)

Pressure/size range: DN10-DN50 = 25 bar / DN65-DN100 = 16 bar / DN125-200 = 10 bar/ DN250 = 8 bar (calculated @ 20°, see s
Elbow short 45°/90° EN10374 Series A-BS-90 (45) ****
Elbow long 45°/90° EN10374 Series A-BL-90 (45) ****

Pressure/size range: DN10-DN50 = 25 bar / DN65-DN80 = 16 bar / DN100 = 12 bar / DN125 = 10 bar / DN150 = 8 bar (calculated
T-piece short EN10374 Series A TS
T-piece long a/ EN10374 Series A TL
T-piece red. short EN10374 Series A TRS
T-piece red. long a/ EN10374 Series A TRL

Pressure/size range: DN10-DN50 = 25 bar / DN65-DN100 = 16 bar / DN125-DN150 = 12 bar / DN200-DN250 = 10 bar (calculated
Reducer concentric short b/ EN10374 Series A RCS
Reducer eccentric short b/ EN10374 Series A RES
Remarks; - Fittings and connectors allowable pressure/ temperature ranges taken from applicable DIN norm and/ or EN standard
- EN standards supersede DIN standards when available and/or mentioned in above SPC
* - Synthetic/ rubber gaskets tracebility according to EC1935/2004
** - Flange type not preffered (not hygienic), only to use in case of supplier standard connections
*** - Lapped pipe end (collar) thickness approximately tubing thickness for inside flush piping connections. PN10 design press
**** - Length bolting minimal 2 windings through the nut after torque
***** - Short version = manually welding _ long version = orbital (automatic) welding
Notes;
a/ See cut to size dimensional table 1 if T-piece reduced is used for valve/ instrumentation welding connections (to achieve
connection size leading

SPC-003 (ISO food) A304

Pipe class:
Tubing material: 1.4307 (A304L)
Fitting material:
Design:
Pressure rating:
Temperature range:
Corrosion allowance:
PED category:

Tubing/ piping
Tube EN standard:
Material: 1.4307 (A304L)

Tube Outside Diameter - OD (mm) Wall Thickness (mm)

25 1,2
38 1,2
51 1,2
63,5 1,6
76,1 1,6
101,6 2
Tri-clamp norm: ISO 2852 *
Material: Supplier standard / A304L (1.4307) or A316L (1.4404)
Pressure/size range: OD 25 / 38 / 51 = 16 bar / OD 63,5 / 76,1 / 101,6 = 10 bar @ -10°*/150°C **
Ferrule: ISO 2852
Closure type: Clamp-ring (SH) - double pin - ISO 2852
Gasket material: EPDM (temp. range -30°C/ 130°C)

Union norm: ISO 2037 / SMS

Material: Supplier standard / A304L (1.4307) or A316L (1.4404)
Pressure/size range: See tubing / pressure range tbd.
Welding male: SMS welding male_ISO 2037
Liner: SMS welding liner_ISO 2037
Nut: SMS nut_ISO 2037
Gasket: SMS gasket
Gasket material: EPDM (temp. range -30°C/ 130°C)

Welding Fittings
Type: ISO 2851 / SMS (swedish milk/dairy standard)
Sizing: See tubing
Material: 1.4307 (A304L) or 1.4301 (A304) ***

Pressure/size range: See tubing / pressure range tbd.

Elbow 45°/90° - 1,5D_long ISO 2851
Elbow 45°/90° - 1,5D_short ISO 2851 ****

Pressure/size range: See tubing / pressure range tbd.

Tee, equal ISO 2851
Tee, equal short ISO 2851 / SMS ****
Tee, equal red ISO 2851 / SMS ****
Tee, equal short red ISO 2851 / SMS ****

Pressure/size range: See tubing / pressure range tbd.

Concentric reducer a/ ISO 2037 / SMS ****
Eccentric reducer a/ ISO 2037 / SMS ****
Remarks; - Long type elbows & Tees preffered for orbital / manipulated (automatic) welding
* - Preffered internal roughness tubing & fittings <= 0,8 µm (standard acc to ISO 2037 = 1,0 µm)
** - Pressure range tri- clamp acc to DIN 32676:2001 clamp single hinged type (tabelle 2)
*** - Preffered material = 1.4307 (A304L)
**** - Based on ISO 2851, sizing acc ISO 2037, not physically mentioned in a standard. SMS standard also optional
Notes;
a/ - Largest DN connection size leading

SPC-004 (ISO food) A316

Pipe class:
Tubing material:
Fitting material:
Design:
Pressure rating:
Temperature range:
Corrosion allowance:
PED category:

Tubing/ piping
Tube EN standard:
Material:

Tube Outside Diameter - OD (mm) Wall Thickness (mm)

25 1,2
38 1,2
51 1,2
63,5 1,6
76,1 1,6
101,6 2

Tri-clamp norm: ISO 2852 *

Material: Supplier standard / A304L (1.4307) or A316L (1.4404)
Pressure/size range: OD 25 / 38 / 51 = 16 bar / OD 63,5 / 76,1 / 101,6 = 10 bar @ -10°*/150°C **
Ferrule: ISO 2852
Closure type: Clamp-ring (SH) - double pin - ISO 2852
Gasket material: EPDM (temp. range -30°C/ 130°C)
Union norm: ISO 2037 / SMS
Material: Supplier standard / 1.4404 (A316L)
Pressure/size range: See tubing / pressure range tbd.
Welding male: SMS welding male_ISO 2037
Liner: SMS welding liner_ISO 2037
Nut: SMS nut_ISO 2037
Gasket: SMS gasket
Gasket material: EPDM (temp. range -30°C/ 130°C)

Welding Fittings
Type: ISO 2851 / SMS (swedish milk/dairy standard)
Sizing: See tubing
Material: 1.4404 (A316L)

Pressure/size range: See tubing / pressure range tbd.

Elbow 45°/90° - 1,5D_long ISO 2851
Elbow 45°/90° - 1,5D_short ISO 2851 ****

Pressure/size range: See tubing / pressure range tbd.

Tee, equal ISO 2851
Tee, equal short ISO 2851 / SMS ****
Tee, equal red ISO 2851 / SMS ***
Tee, equal short red ISO 2851 / SMS ***

Pressure/size range: See tubing / pressure range tbd.

Concentric reducer a/ ISO 2037 / SMS ***
Eccentric reducer a/ ISO 2037 / SMS ***

Remarks; - Long type elbows & Tees preffered for orbital / manipulated (automatic) welding
* - Preffered internal roughness tubing & fittings <= 0,8 µm (standard acc to ISO 2037 = 1,0 µm)
** - Pressure range tri- clamp acc to DIN 32676:2001 clamp single hinged type (tabelle 2)
*** - Based on ISO 2851, sizing acc ISO 2037, not physically mentioned in standard. SMS standard also optional
Notes;
a/ - Largest DN connection size leading

SPC-005 (EN DIN (ISO) Industrial A304)

Pipe class:
Tubing material: 1.4307 (A304L)
Fitting material: 1.4307 (A304L or >) or 1.4404 (A316L) / supplier standard
Design: 10 barg @ 80°C
Pressure rating: 10 barg
Temperature range: 0°C / +80°C
Corrosion allowance: 0 mm
PED category: Art.4, par.3 SEP (sound engineering practice)

Tubing/ piping
Tube EN standard: EN 10217-7
Material: 1.4307 (A304L)
Pressure/size range: DN250= 19 bar@20°C / 16 bar@100°C
Nominal: Outside diameter (mm) Wall Thickness (mm) Norm/standard dimensions & tole
DN - Imperial *
DN10 - 3/8" 17,2 2
DN15 - 1/2"
DN20 - 3/4"
DN25 - 1"
DN32 - 11/4"
DN40 - 11/2"
DN50 - 2"
1127 series 1
DN65 - 21/2"
DN80 - 3"
DN100- 4"
DN125
DN150
DN200
DN250

Connections
Union (BSP) taper seat (welding):
Original ISO 4144 types; U4 (Fem-fem) / U5 (male-fem) or U6 (male-male)

Tri-clamp norm: ISO 1127

Material: Supplier standard / A304L (1.4307) or A316L (1.4404)
Pressure/size range: DN10-DN50 =16 bar / DN65-DN200 =10 bar @ -10°*/150°C
Ferrule: ISO 1127 series 1
Closure type: Clamp-ring - double pin
Gasket material: EPDM (temp. range -30°C/ 130°C) *

Union norm: DIN 11851 ISO **

Material: Supplier standard / A304L (1.4307) or A316L (1.4404)
Pressure/size range: DN10-DN40 = 40 bar / DN50-DN100 = 25 bar / DN125-150 = 10bar @ -10°*/140°C
Welding male: DIN 11851 ISO Form SC
Liner: DIN 11851 ISO Form SD
Nut: DIN 11851 ISO Form F
Gasket: DIN 11851 Form G
Gasket material: EPDM (temp. range -30°C/ 130°C)

Flange norm: EN1092-1

Material: 1.4301/1.4307 (A304(L))
Pressure/size range: PN10 (10bar) @ RT= -10°/ 50°C _ 8,6 bar @ 100°C (in between values to be calculated)
Loose flange: EN1092-1 type 02 DN10-DN40 = PN40, DN50-DN150=PN16, DN200-DN250=PN10
Lapped pipe end: EN1092-1 type 33_Collar thickness (F) DN10-DN250= 2 mm *** DN10-DN250=PN10
Gasket: EN1514.1 type IBC
Gasket material: EPDM (temp. range -30°C/ 130°C)
Bolting: Hexagonal A2-70 ; metrical ISO 4014 (DIN931)****
Nuts: Hexagonal A2-70. ; metrical ISO 4032 (DIN934)

Fittings
Threaded (BSP) fittings norm: ISO 4144
Thread according: EN 10226-1
Material: 1.4401 (A316 or >)
Pressure/size range: 3/8" - 4" _DN10 - DN100 / 20 bar@-20 to +40°C - 16,5 barg@100°C
External tapered thread (R): EN-10226-1 (or ISO 7-1 / BSPT) Rc conical thread
Internal parallel thread (Rp or G): EN-10226-1 (or G/ EN ISO 228-1) Rp parallel thread

Weld fittings norm: EN 10253-4

Material: 1.4307 (A304L)

Pressure/size range: 17,2-168,3 (DN10-DN250)= 2mm DN250=20 barg@20°C / 16 barg@100°C

Elbow 45°/90° - 3D - type A EN 10253-4

Pressure/size range: 21,3-114,3 ar@20°C / 11 bar@100°C

Equal Tee- Fig.4_type A d/ EN 10253-4
Reducing Tee- Fig.5_ type A d/ EN 10253-4
Pressure/size range: c/ 60,3-273 (D 10-DN40) *****
Pulled Tee- Fig.6_ type A c/ EN 10253-4
Pulled Tee Reduced - Fig.6_type A c/ EN 10253-4

Pressure/size range: DN10-DN200 t=2mm & DN250 t=2,6mm

Concentric reducer straight - type A b/ EN 10253-4 DN200/DN100 = 14barg@20°C / 11 barg@100°C
Eccentric reducer straight - type A b/ EN 10253-4 DN200/DN100 = 12 barg@20°C / 10 barg@100°C

Pressure/size range: 33,7-114,3 (DN25-DN100)= 2mm _ 139,7-273 (DN125-250)= 3mm DN250 = 16 barg@20°C /13 barg@100°C
End Cap type A EN 10253-4
Remarks; - Weld fittings type A = Pressure derating acc. EN 10253-4 Pressure factor tables. Type B = full rated pressure of tubing
- EN 10253-4 linked with EN 10217-7 / PED
* - Nominal DN / imperial size column for reference only
** - Supplier specific/ not officially acc.to DIN 11851
*** - Lapped pipe end (collar) thickness approximately tubing thickness for inside flush piping connections. PN10 design pressure rating
**** - Length bolting minimal 2 windings through the nut after torque
***** - See pressure range tubing
Notes;
a/ - Unions are partly according conical type U4-U5. Welding type connections (Butt weld /BW) are not acc to ISO 4144, but supplier specific (see a
S.K.S)
- Other BSP fitting types, like welding nipples, should have a BW end for welding. No cutting of thread on tubing ends allowed b/ - Largest DN con
c/ - DN50 smallest size according EN 10253-4. DN10-40 fittings supplier specific (Dacapo steel). Check availability other suppliers
d/ DN10-DN40 sizes equal Tees Fig.4 & Fig.5 optional (not preffered)

SPC-006 (EN DIN (ISO) Industrial A316)

Pipe class:
Tubing material: 1.4404 (A316L)
Fitting material: 1.4404 (A316L or >)
Design: 10 barg @ 80°C
Pressure rating: 10 barg
Temperature range: 0°C / +80°C
Corrosion allowance: 0 mm
PED category: Art.4, par.3 SEP (sound engineering practice)

Tubing/ piping
Tube EN standard: EN 10217-7
Material: 1.4404 (A316L)
Pressure/size range: DN250= 20 bar@20°C / 17 bar@100°C
 Nominal: Outside diameter (mm) Wall Thickness (mm) d dimensions & toleran
DN - Imperial
DN10 - 3/8"
DN15 - 1/2"
DN20 - 3/4"
DN25 - 1"
DN32 - 11/4"
DN40 - 11/2"
DN50 - 2"
ISO 1127 series 1
DN65 - 21/2"
DN80 - 3"
DN100- 4"
DN125 2
DN150 2
DN200 2,6
DN250 2,6

Connections
Union (BSP) taper seat (welding): a/ Based on ISO 4144 type (BW-fem) / (BW-male) or (BW/BW), see Fittings for sizing
Original ISO 4144 types; U4 (Fem-fem) / U5 (male-fem) or U6 (male-male)

Tri-clamp norm: ISO 1127

Material: 1.4404 (A316L)
Pressure/size range: DN10-DN50 =16 bar / DN65-DN200 =10 bar @ -10°*/150°C
Ferrule: ISO 1127 series 1
Closure type: Clamp-ring - double pin
Gasket material: EPDM (temp. range -30°C/ 130°C) *

Union norm: DIN 11851 ISO **

Material: 1.4404 (A316L)
Pressure/size range: DN10-DN40 = 40 bar / DN50-DN100 = 25 bar / DN125-150 = 10bar @ -10°*/140°C
Welding male: DIN 11851 ISO Form SC
Liner: DIN 11851 ISO Form SD
Nut: DIN 11851 ISO Form F
Gasket: DIN 11851 Form G
Gasket material: EPDM (temp. range -30°C/ 130°C)

Flange norm: EN1092-1

Material: 1.4401/1.4404 (A316(L))
Pressure/size range: PN10 (10bar) @ RT= -10°/ 50°C _ 9,4 bar @ 100°C (in between values to be calculated)
Loose flange: EN1092-1 type 02 DN10-DN40 = PN40, DN50-DN150=PN16, DN200-DN250=PN10
Lapped pipe end: EN1092-1 type 33_Collar thickness (F) DN10-DN250= 2 mm *** DN10-DN250=PN10
Gasket: EN1514.1 type IBC
Gasket material: EPDM (temp. range -30°C/ 130°C)
Bolting: Hexagonal A4-70 ; metrical ISO 4014 (DIN931)****
Nuts: Hexagonal A4-70. ; metrical ISO 4032 (DIN934)

Fittings
Threaded (BSP) fittings norm: ISO 4144
Thread according: EN 10226-1
Material: A316 (1.4401 or >)
Pressure/size range: 3/8" - 4" _DN10 - DN100 / 20 bar@-20 to +40°C - 16,5 barg@100°C
External tapered thread (R): EN-10226-1 (or ISO 7-1 / BSPT) Rc conical thread
Internal parallel thread (Rp or G): EN-10226-1 (or G/ EN ISO 228-1) Rp parallel thread

Weld fittings norm: EN 10253-4

Material: A316L (1.4404)
Pressure/size range: 17,2-168,3 (DN10-DN250)= 2mm DN250=21 barg@20°C / 17 barg@100°C
Elbow 45°/90° - 3D - type A EN 10253-4

Pressure/size range: 21,3-114,3 (DN15-DN100)= 2mm DN100 = 15 bar@20°C / 11 bar@100°C

Equal Tee- Fig.4_type A d/ EN 10253-4
Reducing Tee- Fig.5_ type A d/ EN 10253-4
Pressure/size range: c/ 60,3-273 (DN50-DN250)= 2mm / 17,2-48,3 (DN10-DN40) *****
Pulled Tee- Fig.6_ type A c/ EN 10253-4
Pulled Tee Reduced - Fig.6_type A c/ EN 10253-4

Pressure/size range: DN10-DN200 t=2mm & DN250 t=2,6mm

Concentric reducer straight - type A b/ EN 10253-4 DN200/DN100 = 15barg@20°C / 11 barg@100°C
Eccentric reducer straight - type A b/ EN 10253-4 DN200/DN100 = 13 barg@20°C / 10 barg@100°C

Pressure/size range: 33,7-114,3 (DN25-DN100)= 2mm _ 139,7-273 (DN125-250)= 3mm DN250 = 17 barg@20°C /13 barg@100°C
End Cap type A EN 10253-4
Remarks; - Weld fittings type A = Pressure derating acc. EN 10253-4 Pressure factor tables. Type B = full rated pressure of tubing
- EN 10253-4 linked with EN 10217-7 / PED
* - Nominal DN size column for reference only
** - Supplier specific/ not officially acc.to DIN 11851
*** - Lapped pipe end (collar) thickness approximately tubing thickness for inside flush piping connections. PN10 design pressure rating
**** - Length bolting minimal 2 windings through the nut after torque
***** - See pressure range tubing
Notes;
a/ - Unions are partly according conical type U4-U5. Welding type connections (Butt weld /BW) are not acc to ISO 4144, but supplier specific (see a.o. D
S.K.S)
- Other BSP fitting types, like welding nipples, should have a BW end for welding. No cutting of thread on tubing ends allowed b/ - Largest DN connecti
c/ - DN50 smallest size according EN 10253-4. DN10-40 fittings supplier specific (Dacapo steel). Check availability other suppliers
d/ DN10-DN40 sizes equal Tees Fig.4 & Fig.5 optional (not preffered)

SPC-013 (EN (DIN ISO) Industrial A316)

Pipe class:
Tubing material: A316L (1.4404)
Fitting material: A316L (1.4404 or >)
Design: 10 barg @ 35°C
Pressure rating: 10 barg @ DN100
Temperature range: 0°C / +35°C
Corrosion allowance: < =0,1 mm
PED Category: Art.4, par.3 SEP (sound engineering practice)
Tubing/ piping

Tube EN standard: EN 10217-7

Material: A316L (1.4404)
Nominal: Outside diameter (mm) Wall Thickness (mm)
DN
10 17,2 2,3
15 21,3 2,6
20 26,9 2,6
25 33,7 2,6
32 42,4 2,6
40 48,3 2,6
50 60,3 2,6
65 76,1 2,6
80 88,9 2,6
100 114,3 2,6

Connections

Flange norm: EN1092-1

Material: A316L (1.4404)
Pressure/size range: PN10= 10bar @ RT= -10°/ 50°C _ 9,4 bar @ 100°C (in between values to be calculated)
Loose flange: EN 1092-1 type 02
Lapped pipe end: EN 1092-1 type 33
Gasket: EN 1514-1 Form IBC
Gasket material: FKM / Viton vulcanised
Bolting: Hexagonal A4-70 ; metrical ISO 4014 (DIN931)****
Nuts: Hexagonal A4-70. ; metrical ISO 4032 (DIN934)

Fittings
Weld fittings norm: EN 10253-3 *
Material: A316L (1.4404)
Nominal: Outside diameter (mm) Wall Thickness (mm) **
DN

15 21,3 2,6
20 26,9 2,6
25 33,7 2,6
32 42,4 2,6
40 48,3 2,6
50 60,3 2,6
65 76,1 2,6
80 88,9 2,6
100 114,3 2,6
Pressure/size range: DN15 (21,3x2,6 (~378 barg)) - DN100 (114,3x2,6 (~45 barg) barg@20°C
Elbow 45°/90° EN 10253-3 type 3D

Pressure/size range: DN15 (21,3x2,6 (~100 barg)) - DN100 (114,3x2,6 (~19 barg) barg@20°C
Equal Tee pressed EN 10253-3 Equal tee (pressed)
Reducing Tee pressed EN 10253-3 Reducing tee (pressed)

Pressure/size range: DN15/20 (26,9/ 21,3x2,6 (~194 barg)) - DN100/40 (114,3/ 48,3x2,6 (~55 barg) barg@20°C
Reducer concentric EN 10253-3 conc red ***
Reducer eccentric EN 10253-3 ecc red ***

Remarks;
* - EN 10253-3 only applicable for PED/ SEP (Art.4/Par.3).
** - ASME A403/ ASME B16.9 (schedule 10/ 40) optional for obtaining minimal 2,6mm wall thickness.
Approx. 10% thicker allowed. Structural/ main dimensions should be compatible.
*** - Reducer structural dimension (length) EN 10253 / ASMEA403 compatible. EN 10253 straight type not applicable.
**** - Length bolting minimal 2 windings through the nut after torque.
Notes;
- Fitting pressure @ 20°C based on 1.4307 material.
- Temperature range 35° @ 5% Sulfuric acid, 40° C @ 96% Sulfuric acid
- 0,1 mm corrosion allowance/ year taken into account for a minimal tubing lifetime of 10 years.
od A304)

& tolerances

EN10357-series A (DIN11850 Reihe 2)

0°*/140°C
o be calculated)
250=PN10
DN250=PN10

N250 = 8 bar (calculated @ 20°, see standard)

= 10 bar / DN150 = 8 bar (calculated @ 20°, see standard )

/ DN200-DN250 = 10 bar (calculated @ 20°, see standard )

IN norm and/ or EN standard

tions
connections. PN10 design pressure rating

elding connections (to achieve minimal pocket) b/ Largest DN connection size

od A316)

Norm/standard dimensions & tolerances

-series A (DIN11850 Reihe 2)

@ -10°*/140°C

s to be calculated)
DN250=PN10
0-DN250=PN10

DN250 = 8 bar (calculated @ 20°, see standard)

25 = 10 bar / DN150 = 8 bar (calculated @ 20°, see standard )

ar / DN200-DN250 = 10 bar (calculated @ 20°, see standard )

le DIN norm and/ or EN standard

nections
ping connections. PN10 design pressure rating

on welding connections (to achieve minimal pocket) b/ Largest DN

ood) A304

hickness (mm) Norm/standard dimensions & tolerances

1,2
1,2
1,2
1,6
1,6 ISO 1127 series 2 / OD 76,1 acc. series 1
2
4404)
6 = 10 bar @ -10°*/150°C **

4404)
 lding
O 2037 = 1,0 µm)
abelle 2)

rd. SMS standard also optional

ood) A316

hickness (mm) Norm/standard dimensions & tolerances

1,2
1,2
1,2
1,6
1,6 ISO 1127 series 2 / OD 76,1 acc. series 1
2

4404)
6 = 10 bar @ -10°*/150°C **
 lding
O 2037 = 1,0 µm)
abelle 2)
d. SMS standard also optional
 Norm/standard dimensions & tolerances

1127 series 1

e)

10°*/140°C

o be calculated)
N250=PN10
DN250=PN10
0°C

°C

N250 = 16 barg@20°C /13 barg@100°C

pressure of tubing

ns. PN10 design pressure rating

acc to ISO 4144, but supplier specific (see a.o. Dacapo steel /

lowed b/ - Largest DN connection size leading

heck availability other suppliers
 d dimensions & tolerances

ISO 1127 series 1

sizing

140°C

calculated)
=PN10
0=PN10
 DN250 = 17 barg@20°C /13 barg@100°C

ure of tubing

N10 design pressure rating

o ISO 4144, but supplier specific (see a.o. Dacapo steel /

lowed b/ - Largest DN connection size leading
availability other suppliers

16)
 Norm/standard dimensions & tolerances

ISO 1127

n values to be calculated)

Norm/standard dimensions & tolerances

EN 10253-3 / ISO 1127 (ISO 5251)

ASME A403/ ASME B16.9 (MSS-SP43) **
 barg@20°C

barg@20°C

8,3x2,6 (~55 barg) barg@20°C

all thickness.

straight type not applicable.