C:\DiaSys\ECU_7\527111568 yangung1\527111568 yangung1 527111568 / Main

Single-parameters
ParNo Parameter PC-value Acti ve-value Startup-value Unit

1. 0100.005 P-Lube Oil Default Value 5. 00000 5.00000 5.00000 bar

1. 0102.005 P-Fuel Default Value 6. 00000 6.00000 6.00000 bar

1. 0103.005 P-Charge Air Default Valu e 3. 00000 3.00000 3.00000 bar

1. 0104.005 P-HD Default Value 1800 1800 1800 barHD

1. 0105.005 P-HD Unfiltered Default Value 1800 1800 1800 barHD

1. 0106.005 P-CrankCase Default Value 0.00 0.00 0. 00 mbar

Adapt P-Crankcas e Monitorin g

1. 0106.023 Ac tive

1. 0106.024 T1 P-Crank case Filter 240. 000 240.000 240.000 s

Adapt P-Crankcas e Learning

1. 0106.029
Ac tive

P-Crankc ase Learnin g Cor.

1. 0106.030 0. 020 0.020 0.020 pts
Perc ent

1. 0106.031 P-Crankc ase Statio nary Time 150. 000 150.000 150.000 s

Adaptive P-Crankcas e
1. 0106.032 100.0 100. 0 100.0 Nm
Hysterese Tq

Adaptive P-Crankcas e Hyst.

1. 0106.033 EngSpeed 20.0 20.0 20.0 rpm

1. 0110.002 P-Aux 1 ECU Channel -1 -1 -1 digit

1. 0110.003 P-Aux 1 Filter Time Cons t 0. 100 0.100 0.100 s

1. 0110.005 P-Aux 1 Default Valu e 0. 00000 0.00000 0.00000 bar

1. 0120.005 T-Coolant Def ault Value 100.00 100.00 100. 00 degC

1. 0121.005 T-Charge Air Default Valu e 80.00 80.00 80.00 degC

1. 0122.005 T-Fuel Default Value 55.00 55.00 55.00 degC

T-Coolant InterCooler Default

1. 0124.005 70.00 70.00 70.00 degC
Value

1. 0125.005 T-Lube Oil Default Valu e 95.00 95.00 95.00 degC

1. 0130.005 T-Aux 1 Default Valu e 0.00 0.00 0. 00 degC

1. 0152.002 Level Coolant ECU Channel 16 16 16 digit

Level Coolant Interc. ECU

1. 0153.002 Channel 18 18 18 digit

1. 0159.910 SD P-O il Refill Pump 209 209 209 digit

1. 0160.002 Aux 1 ECU Channel 40 40 40 digit

2019-03-02 15:28 - 273048_HUYNH Page 1 of 22

C:\DiaSys\ECU_7\527111568 yangung1\527111568 yangung1 527111568 / Main
Single-parameters
ParNo Parameter PC-value Acti ve-value Startup-value Unit

1. 0160.003 Aux 1 Filter Time Cons t 0. 100 0.100 0.100 s

1. 0160.005 Aux 1 Default Valu e 0 0 0 digit

EMU Max. Allowed Speed

1. 0600.015 50.0 50.0 50.0 rpm
Difference

1. 0600.016 EMU Speed SD Alarm Dela y 10.000 10.000 10.000 s

1. 1005.001 Delay after Start 10.000 10.000 10.000 s

1. 1005.004 ES Failure Blink Signal Dela y 30.000 30.000 30.000 s

1. 1005.019 Configuratio n ETC on Engine 261 261 261 digit

1. 1005.020 Rated Power 1965.000 1965.000 1965.000 kW

1. 1005.022 Engin e Optimized 1 1 1 digit

1. 1020.005 Engin e Series 4000 4000 4000 digit

1. 1020.006 Number of Cylinders 16 16 16 digit

Pilot / Post Fuel Mas ses via

1. 1020.018
Dialog
SRS-SD-Emergency Operatio n
1. 1020.019 allowed

1. 1020.020 IRT-Meas uring act ive (Mode 2)

1. 1020.031 Maximum allowed Speed 1930.0 1930.0 1930.0 rpm

1. 1020.045 PLD-Engine

Short Measure Win dow

1. 1020.047
(IRT-Detect.)

1. 1020.048 Delete Min-Max-IRT-Valu es

1. 1020.085 IRT Measuring Time 0. 600 0.600 0.600 ms

1. 1021.001 InjTest half engine test allowed

1. 1021.002 InjTest wait time before tes t 20 20 20 sec

1. 1021.003 InjTest duratio n per cylinder 20 20 20 sec

1. 1021.004 InjTest break t im e m ultip lie r 0. 500 0.500 0.500 pts

InjTest min. coolant

1. 1021.005 temperature 70.00 70.00 70.00 degC

1. 1021.006 InjTest allowed

1. 1021.010 InjTest min. speed full engin e 0.0 0. 0 0.0 rpm

2019-03-02 15:28 - 273048_HUYNH Page 2 of 22

C:\DiaSys\ECU_7\527111568 yangung1\527111568 yangung1 527111568 / Main
Single-parameters
ParNo Parameter PC-value Acti ve-value Startup-value Unit

1. 1021.011 InjTest max. s peed full engine 3000.0 3000.0 3000.0 rpm

1. 1021.012 InjTest min. fuel quant. full eng 15.00 15.00 15.00 mm3/H

1. 1021.013 InjTest max. fuel quant. full eng 10000.00 10000.00 10000. 00 mm3/H

1. 1021.014 InjTest opt. speed full eng 0.0 0. 0 0.0 rpm

1. 1021.015 InjTest opt. quant. full eng 0.00 0.00 0. 00 mm3/H

1. 1021.020 InjTest min. speed half engine 0.0 0. 0 0.0 rpm

1. 1021.021 InjTest max. s peed half engine 2000.0 2000.0 2000.0 rpm

InjTest min. fuel quant. half

1. 1021.022 eng 0.00 0.00 0. 00 mm3/H

InjTest max. fuel quant. half

1. 1021.023 1000.00 1000.00 1000.00 mm3/H
eng

1. 1021.024 InjTest opt. speed half engine 0.0 0. 0 0.0 rpm

1. 1021.025 InjTest opt. fuel quant. half eng 0.00 0.00 0. 00 mm3/H

1. 1021.030 InjTest time speed fin ds level 12 12 12 sec

1. 1021.040 InjTest Filter T fuel quant. 0. 200 0.200 0.200 s

1. 1021.044 Evalu at ion max. dev. speed 1. 000 1.000 1.000 %

Evalu at ion max.dev. fuel quant.

1. 1021.045 neg 50.000 50.000 50.000 %

Evalu at ion max.dev. fuel quant.

1. 1021.046 pos 50.000 50.000 50.000 %

1. 1021.047 Evalu at ion inj. test active

1. 1024.004 Inj. Cutout fixed Speed allowed

1. 1024.005 Inj. Cutout fixed Speed 0.0 0. 0 0.0 rpm

Virtual Temp. BOI Warm-Up 1.0120.001 1.0120.001 1.0120.001

1. 1030.005 PV
PV 1 T-Coolant T-Coolant T-Coolant

Virtual Temp. BOI Warm-Up 1.0121.001 1.0121.001 1.0121.001

1. 1030.006 PV 2 T-Charge Air T-Charge Air T-Charge Air PV

Factor Virtual Temp. BOI

1. 1030.007 Warm-Up 1. 000 1.000 1.000 pts

Virtual Temp. Friction Torque 1.0120.001 1.0120.001 1.0120.001

1. 1030.009 PV 1 T-Coolant T-Coolant T-Coolant PV

Virtual Temp. Friction Torque 1.0120.001 1.0120.001 1.0120.001

1. 1030.010 PV 2 T-Coolant T-Coolant T-Coolant PV

Factor Virtual Temp.

1. 1030.011 0. 000 0.000 0.000 pts
FrictionTorque

Virtual Temp. Half Engine 1.0121.001 1.0121.001 1.0121.001

1. 1030.013 PV
Mode PV 1 T-Charge Air T-Charge Air T-Charge Air

2019-03-02 15:28 - 273048_HUYNH Page 3 of 22

C:\DiaSys\ECU_7\527111568 yangung1\527111568 yangung1 527111568 / Main
Single-parameters
ParNo Parameter PC-value Acti ve-value Startup-value Unit

Virtual Temp. Half Engine 1.0120.001 1.0120.001 1.0120.001

1. 1030.014 PV
Mode PV 2 T-Coolant T-Coolant T-Coolant

1. 1040.005 Bin Out TO1 Active Level

1. 1040.006 Bin Out TO2 Active Level

1. 1040.008 Bin Out TO4 Active Level

1. 1044.001 PW M_CM1 Mode Perio d Period Perio d

PW M_CM1 Source PV Freq or 1.1300.126 PW M 1.1300.126 1.1300.126

1. 1044.002 Perio d Perio d Time PW M Perio d PW M Perio d PV
Time Time
1.1300.116 Fuel 1.1300.116 Fuel 1.1300.116 Fuel
1. 1044.003 PW M_CM1 Source PV Rat io Pump PWM Pump PWM Pump PWM PV

1. 1044.004 PW M_CM1 Error Handling No Error No Error No Error

1. 1045.001 PW M_CM2 Mode PW M Off PW M Off PW M Off

PW M_CM2 Source PV Freq or

1. 1045.002 Not used Not used Not used PV
Perio d

1. 1045.003 PW M_CM2 Source PV Rat io Not used Not used Not used PV

1. 1045.004 PW M_CM2 Error Handling PW M Act ive PW M Active PW M Act ive

1. 1046.001 PW M1 Mode PW M Off PW M Off PW M Off

PW M1 Source PV Freq or
1. 1046.002 Perio d Not used Not used Not used PV

1. 1046.003 PW M1 Source PV Ratio Not used Not used Not used PV

1. 1046.004 PW M1 Error Handling PW M Act ive PW M Active PW M Act ive

1. 1047.001 PW M2 Mode PW M Off PW M Off PW M Off

PW M2 Source PV Freq or
1. 1047.002 Not used Not used Not used PV
Perio d

1. 1047.003 PW M2 Source PV Ratio Not used Not used Not used PV

1. 1047.004 PW M2 Error Handling PW M Act ive PW M Active PW M Act ive

1. 1070.003 Engin e running Speed Limit 300.0 300. 0 300.0 rpm

1. 1075.001 Cylinder Volume 4767 4767 4767 ml

1. 1075.002 Start Torque Min . 4000.0 4000.0 4000.0 Nm

1. 1075.003 Start Torque RampUp 1000.000 1000.000 1000.000 pts

1. 1075.005 Torque Limit SD 200000.0 200000.0 200000.0 Nm

Deact. Override Torque Lim.

1. 1075.006
SD

2019-03-02 15:28 - 273048_HUYNH Page 4 of 22

C:\DiaSys\ECU_7\527111568 yangung1\527111568 yangung1 527111568 / Main
Single-parameters
ParNo Parameter PC-value Acti ve-value Startup-value Unit

1. 1075.020 P-Rail Fuel Start Lim 300 300 300 barHD

1. 1075.021 P-Rail Fuel Torque Lim Start -1000.0 -1000. 0 -1000.0 Nm

1. 1075.063 Min. Torque Limit Value LDA 2800.0 2800.0 2800.0 Nm

1. 1085.001 DBR/MCR Func tion Ac tive

DBR/MCR Delay Start

1. 1085.004 Reduct ion (T1) 15.000 15.000 15.000 s

DBR/MCR Duration of
1. 1085.005 Reduct ion (T2) 22.000 22.000 22.000 s

1. 1085.006 DBR/MCR Recovery Time (T3) 1800.000 1800.000 1800.000 s

DBR/MCR Reduction Recov.

1. 1085.007 Time (T4) 1740.000 1740.000 1740.000 s

1. 1085.008 MCR Reduction Dela y 0. 000 0.000 0.000 s

1. 1088.001 Max average power 85.000 85.000 85.000 %

1. 1100.045 Ac tivate Transient BOI

1. 1300.033 Grad. Monit. Lower Press ure 100 100 100 barHD

1. 1300.034 Grad. Monit. Upper Pressure 500 500 500 barHD

1. 1300.035 Grad. Monit. Period Start 0. 300 0.300 0.300 s

1. 1300.036 Grad. Monit. Limit Start 20 20 20 bHD/s

1. 1300.037 Grad. Monit. Period Stop 0. 500 0.500 0.500 s

1. 1300.038 Grad. Monit. Limit Stop -300 -300 -300 bHD/s

1. 1300.039 Grad. Monit.-Start Ac tive

1. 1300.040 Grad. Monit.-Stop Active

1. 2500.001 Speed Calcula tion Config . 0 0 0 digit

1. 2500.002 Speed Calcula tion Low Limit 80.0 80.0 80.0 rpm

1. 2500.003 Speed Calcula tion High Limit 3000.0 3000.0 3000.0 rpm

1. 2500.004 Standst ill Time 0. 200 0.200 0.200 s

1. 2500.005 Speed Filter Switc h. Poin t 1000.0 1000.0 1000.0 rpm

1. 2500.006 Speed Filter Switc h. Hyst erese 100.0 100. 0 100.0 rpm

1. 2500.007 Filter Angle KW-New Filter 90.000 90.000 90.000 deg

2019-03-02 15:28 - 273048_HUYNH Page 5 of 22

C:\DiaSys\ECU_7\527111568 yangung1\527111568 yangung1 527111568 / Main
Single-parameters
ParNo Parameter PC-value Acti ve-value Startup-value Unit

1. 2500.008 t1-New Filter 0. 050 0.050 0.050 s

Filter Angle KW-Constant

1. 2500.009 360. 000 360.000 360.000 deg
Angle

1. 2500.011 Filter Angle KW-Tes t Speed 1 15.000 15.000 15.000 deg

1. 2500.012 Filter Angle KW-Tes t Speed 2 15.000 15.000 15.000 deg

1. 2500.014 Filter Angle KW-Angle 1 360. 000 360.000 360.000 deg

1. 2500.015 Filter Angle KW-Angle 2 720. 000 720.000 720.000 deg

1. 2500.017 Filter Angle NW-Test Speed 1 16.000 16.000 16.000 deg

1. 2500.020 Filter Angle NW-Angle 1 180. 000 180.000 180.000 deg

1. 2500.021 Filter Angle NW-Angle 2 360. 000 360.000 360.000 deg

1. 2500.025 Engin e Idle Speed 600.0 600. 0 600.0 rpm

1. 3000.001 Full Engine Speed Switchpoint 3000.0 3000.0 3000.0 rpm

1. 3000.002 Full Engine Speed Hysteresis 0.0 0. 0 0.0 rpm

1. 3000.004 Full Engine Torque Hysteresis 150.0 150. 0 150.0 Nm

1. 3000.005 Half Engine Dela y af ter Start 10.000 10.000 10.000 s

1. 3000.006 Half Engine Activatio n Delay 0. 500 0.500 0.500 s

1. 3000.007 Half Engine Switchover Time 420. 000 420.000 420.000 s

1. 3000.008 Half Engine Switchover Delay 0. 000 0.000 0.000 s

1. 3000.009 Alt ernate Half Engine Mode

1. 3000.010 Ac tive Cylinders Bank A at ZA 255 255 255 digit

1. 3000.011 Ac tive Cylinders Bank B at ZA 0 0 0 digit

1. 3000.015 Half Engine Mode Temp Limit 200.00 200.00 200. 00 degC

1. 3000.016 Half Engine Temp Limit Hyst 10.00 10.00 10.00 degC

1. 3011.005 1 Charger Tooth active

1. 8009.050 Op. Hours Inje ctor Change 0 0 0 h

1. 8009.051 Fuel Cons. Corr. per 1000 h 0. 000 0.000 0.000 %

1. 8010.001 Crash Recorder ON

2019-03-02 15:28 - 273048_HUYNH Page 6 of 22

C:\DiaSys\ECU_7\527111568 yangung1\527111568 yangung1 527111568 / Main
Single-parameters
ParNo Parameter PC-value Acti ve-value Startup-value Unit

1. 8010.002 Stop Triggers Crash Rec.

1. 8011.101 PV Rec order 1 active

1.0121.001 1.0121.001 1.0121.001

1. 8011.102 PV Rec order 1 PV PV
T-Charge Air T-Charge Air T-Charge Air

1. 8011.103 PV Rec order 1 Lower Limit 4500 4500 4500 digit

1. 8011.104 PV Rec order 1 Upper Limit 6000 6000 6000 digit

1. 8011.201 PV Rec order 2 active

1.0100.001 P-Lube 1.0100.001 1.0100.001

1. 8011.202 PV Rec order 2 PV Oil after Filter P-Lube Oil after P-Lube Oil after PV
Filter Filter
1. 8011.203 PV Rec order 2 Lower Limit 350000 350000 350000 digit

1. 8011.204 PV Rec order 2 Upper Limit 550000 550000 550000 digit

1. 8011.301 PV Rec order 3 active

1.0120.001 1.0120.001 1.0120.001

1. 8011.302 PV Rec order 3 PV PV
T-Coolant T-Coolant T-Coolant

1. 8011.303 PV Rec order 3 Lower Limit 8500 8500 8500 digit

1. 8011.304 PV Rec order 3 Upper Limit 10500 10500 10500 digit

1. 8011.401 PV Rec order 4 active

1. 8011.402 PV Rec order 4 PV Not used Not used Not used PV

1. 8011.403 PV Rec order 4 Lower Limit 0 0 0 digit

1. 8011.404 PV Rec order 4 Upper Limit 0 0 0 digit

1. 9901.100 Sens ortype Input PI1 -1 -1 -1 digit

1. 9901.101 Sens ortype Input PI2 10 10 10 digit

1. 9901.102 Sens ortype Input PI3 6 6 6 digit

1. 9901.103 Sens ortype Input PI4 9 9 9 digit

1. 9901.104 Sens ortype Input PI5 5 5 5 digit

1. 9901.105 Sens ortype Input PI6 -1 -1 -1 digit

1. 9901.106 Sens ortype Input PI7 3 3 3 digit

1. 9901.107 Sens ortype Input PI8 -1 -1 -1 digit

1. 9901.108 Sens ortype Input PI9 -1 -1 -1 digit

2019-03-02 15:28 - 273048_HUYNH Page 7 of 22

C:\DiaSys\ECU_7\527111568 yangung1\527111568 yangung1 527111568 / Main
Single-parameters
ParNo Parameter PC-value Acti ve-value Startup-value Unit

1. 9901.109 Sens ortype Input PI10 -1 -1 -1 digit

1. 9901.110 Sens ortype Input PI11 -1 -1 -1 digit

1. 9901.111 Sens ortype Input PI12 -1 -1 -1 digit

1. 9901.112 Sens ortype Input PI13 -1 -1 -1 digit

1. 9901.113 Sens ortype Input PI14 -1 -1 -1 digit

1. 9901.114 Sens ortype Input PTI1 -1 -1 -1 digit

1. 9901.115 Sens ortype Input PTI2 -1 -1 -1 digit

1. 9901.116 Sens ortype Input LSI1 14 14 14 digit

1. 9901.117 Sens ortype Input LSI2 -1 -1 -1 digit

1. 9901.118 Sens ortype Input LSI3 14 14 14 digit

1. 9901.119 Sens ortype Input TI1 0 0 0 digit

1. 9901.120 Sens ortype Input TI2 0 0 0 digit

1. 9901.121 Sens ortype Input TI3 0 0 0 digit

1. 9901.122 Sens ortype Input TI4 -1 -1 -1 digit

1. 9901.123 Sens ortype Input TI5 -1 -1 -1 digit

1. 9901.124 Sens ortype Input TI6 0 0 0 digit

1. 9901.125 Sens ortype Input TI7 0 0 0 digit

1. 9901.126 Sens ortype Input TI8 -1 -1 -1 digit

1. 9901.127 Sens ortype Input TI9 -1 -1 -1 digit

1. 9901.128 Sens ortype Input TI10 -1 -1 -1 digit

1. 9901.129 Sens ortype Input TI11 -1 -1 -1 digit

1. 9901.130 Sens ortype Input TI12 -1 -1 -1 digit

1. 9901.131 Sens ortype Input KTY 20 20 20 digit

1. 9901.132 Sens ortype Input U_PDU 13 13 13 digit

1. 9901.133 Sens ortype Input PWM_CM1_I 22 22 22 digit

1. 9901.134 Sens ortype Input PWM_CM2_I -1 -1 -1 digit

2019-03-02 15:28 - 273048_HUYNH Page 8 of 22

C:\DiaSys\ECU_7\527111568 yangung1\527111568 yangung1 527111568 / Main
Single-parameters
ParNo Parameter PC-value Acti ve-value Startup-value Unit

1. 9906.001 LevSensTest Test-Time 30.000 30.000 30.000 s

1. 9906.002 LevSensTest Time Power Off 10.000 10.000 10.000 s

LevSensTest Scan after

1. 9906.003 1. 000 1.000 1.000 s
PowerON

1. 9906.004 LevSensTest Testinterval 3600.000 3600.000 3600.000 s

1. 9906.010 LevSensTest LSI 1 active

1. 9906.012 LevSensTest LSI 3 active

2. 0010.001 Test Bench Mode On

2. 0010.012 Order Number Series 0 0 0 digit

2. 0010.013 Pla nt Number Series 0 0 0 digit

2. 0010.014 Applicatio n Code Genset Genset Genset

2. 0280.002 Speed Demand ECU Channel 0 0 0 digit

Speed Demand FilterTime

2. 0280.003 0. 100 0.100 0.100 s
Const.

2. 0280.005 Speed Demand Default Value 0.0 0. 0 0.0 rpm

2. 0283.002 Load Signal % ECU Chan -1 -1 -1 digit

Load Signal % FilterTime

2. 0283.003 Const 0. 100 0.100 0.100 s

2. 0283.009 Load Signal % Default Valu e 0. 000 0.000 0.000 %

Freq. Input RPM FilterTime

2. 0286.003 0. 100 0.100 0.100 s
Const
Idle /End-Torque[%] ECU
2. 0287.002 -1 -1 -1 digit
Channel
Idle /End-Torq[%] FilterTime
2. 0287.003 0. 000 0.000 0.000 s
Const

2. 0287.009 Idle /End-Torq[%] Default Value 0. 000 0.000 0.000 %

Generator Voltage FilterTime

2. 0288.003 Const 0. 100 0.100 0.100 s

Generator Power FilterTime

2. 0289.003 Const. 0. 100 0.100 0.100 s

2. 0500.001 CAN Interface Config urat ion 642 642 642 digit

2. 0500.002 CAN ECU Node-No. 2 2 2 digit

2. 0500.003 CAN Transmit Base-ID 0 0 0 digit

2. 0500.004 CAN FSW Emulat ion 0 0 0 digit

2019-03-02 15:28 - 273048_HUYNH Page 9 of 22

C:\DiaSys\ECU_7\527111568 yangung1\527111568 yangung1 527111568 / Main
Single-parameters
ParNo Parameter PC-value Acti ve-value Startup-value Unit

2. 0500.005 CAN Monitored Nodes 32 32 32 digit

2. 0500.006 CAN Sys tem Start Delay Time 5 5 5 sec

CAN Latest Transmit

2. 0500.007 20 20 20 sec
Repetit ion

2. 0500.008 CAN PU-Module Type/No. 501 501 501 digit

CAN PPS
2. 0500.009 StartMonitorDelayTime 40 40 40 sec

CAN PIM
2. 0500.010 StartMonitorDelayTime 25 25 25 sec

CAN EMU GSW Download

2. 0500.011 Time 60 60 60 sec

CAN EMU PU Data Download

2. 0500.012 Time 30 30 30 sec

2. 1000.001 CAN Torque Active

2. 1000.002 Load Signal Active

2. 1000.003 Load Signal Analog Active

2. 1000.004 Load Signal CAN Active

Test Func t.-Speed Demand

2. 1000.005 Ret. Mode

Test Func t.-Speed Demand

2. 1000.006 Start

2. 1000.007 Speed Cont roller Config. 0 0 0 digit

2. 1000.008 v-Speed Governor (Gain) 400 400 400 digit

2. 1000.009 Stat. Adap.-Min. Torque 100.0 100. 0 100.0 Nm

2. 1000.010 Stat. Adap.-Min. Speed 80.0 80.0 80.0 rpm

2. 1000.011 Speed Governor (kp) 300 300 300 digit

2. 1000.012 Speed Governor (kpmin) 2000 2000 2000 digit

2. 1000.013 Speed Governor (tn) 0. 350 0.350 0.350 s

2. 1000.014 Speed Governor (tv) 0. 000 0.000 0.000 s

2. 1000.015 Speed Governor (t1) 0. 020 0.020 0.020 s

2. 1000.016 Adap. Speed Gov.-Tqmin 0.0 0. 0 0.0 Nm

2. 1000.017 Adap. Speed Gov.-Tqmax 6000.0 6000.0 6000.0 Nm

2. 1000.018 Adap. Speed Gov.-tv(Tqmin ) 0. 020 0.020 0.020 s

2019-03-02 15:28 - 273048_HUYNH Page 10 of 22

C:\DiaSys\ECU_7\527111568 yangung1\527111568 yangung1 527111568 / Main
Single-parameters
ParNo Parameter PC-value Acti ve-value Startup-value Unit

2. 1000.019 Adap. Speed Gov.-tv(Tqmax) 0. 050 0.050 0.050 s

Dyn. Adaption-Activatio n
2. 1000.020 0.0 0. 0 0.0 rpm
Speed

Dyn. Adaption-Low Lim. Load

2. 1000.021 5.0 5. 0 5.0 rpm
On

Dyn. Adaption-Low Lim Load

2. 1000.022 5.0 5. 0 5.0 rpm
Off

2. 1000.023 Dyn. Adaption-High Limit 200.0 200. 0 200.0 rpm

2. 1000.024 Dyn. Adaption-Param. Load On 130 130 130 digit

2. 1000.025 Dyn. Adaption-Param. Load Off 5 5 5 digit

2. 1000.026 tv-Load Signal 2. 000 2.000 2.000 s

2. 1000.027 t1-Load Signal 1. 000 1.000 1.000 s

2. 1000.028 Load Signal Upper Limit Hyst. 500.0 500. 0 500.0 Nm

2. 1000.029 Load Signal Lower Limit Hyst. -500.0 -500.0 -500.0 Nm

2. 1000.030 Load Signal Min. Torque 20.0 20.0 20.0 Nm

2. 1000.031 Load Signal Rele ase Speed 0.0 0. 0 0.0 rpm

Load Signal Max. Requ.

2. 1000.032 Torque 6000.0 6000.0 6000.0 Nm

CAN Torque Max. Requ.

2. 1000.033 Torque 6000.0 6000.0 6000.0 Nm

2. 1000.034 Test Func t.-Init. Speed 600.0 600. 0 600.0 rpm

2. 1000.035 Test Func t.-End Speed 600.0 600. 0 600.0 rpm

2. 1000.036 Test Func t.-Forw. Dela y 40.000 40.000 40.000 s

2. 1000.037 Test Func t.-Return Delay 25.000 25.000 25.000 s

2. 1000.038 Requested Torque Input 0.0 0. 0 0.0 Nm

2. 1000.039 Torque at Zero Fuel Quantit y -250.0 -250.0 -250.0 Nm

2. 1000.064 2:v-Speed Governor (Gain ) 400 400 400 digit

2. 1000.065 2:Speed Governor (kpmin ) 1700 1700 1700 digit

2. 1000.066 2:Speed Governor (tn) 0. 350 0.350 0.350 s

2. 1000.067 2:Speed Governor (tv) 0. 000 0.000 0.000 s

2. 1010.001 Idle /End-Governor Active

2019-03-02 15:28 - 273048_HUYNH Page 11 of 22

C:\DiaSys\ECU_7\527111568 yangung1\527111568 yangung1 527111568 / Main
Single-parameters
ParNo Parameter PC-value Acti ve-value Startup-value Unit

PDT1-Part Act ive End

2. 1010.002
Governor

2. 1010.003 PDT1-Part Act ive Idle Governor

2. 1010.004 Idle /End-Max. Torque Input 20000.0 20000. 0 20000.0 Nm

2. 1010.005 Hysteresis Idle Governor 100.0 100. 0 100.0 Nm

2. 1010.006 Par. Grad. Idle Act. Speed 0 0 0 digit

2. 1010.007 Speed Devia tion Idle Governor 0.0 0. 0 0.0 rpm

2. 1010.008 Par. Grad. Idle Requ. Speed 0 0 0 digit

2. 1010.009 Par. Grad. Idle Integral-Part 0 0 0 digit

2. 1010.010 I-Part Demand Idle Speed 0.0 0. 0 0.0 Nm

2. 1010.011 t1-Requ. Torque Idle Governor 0. 200 0.200 0.200 s

2. 1010.012 Par. Grad. End Act . Speed 0 0 0 digit

2. 1010.013 Speed Devia tion End Governor 0.0 0. 0 0.0 rpm

2. 1010.014 Par. Grad. End Requ. Speed 0 0 0 digit

2. 1010.015 Par. Grad. End Integral-Part 0 0 0 digit

2. 1010.016 Hysteresis End Governor 100.0 100. 0 100.0 Nm

2. 1010.017 t1-Requ. Torque End Governor 0. 200 0.200 0.200 s

2. 1010.018 Grad. Calculat ion Perio d 0. 100 0.100 0.100 s

2. 1010.019 Speed Grad. Filt er Time 0. 050 0.050 0.050 s

2. 1010.020 t1-Speed Gov. I-Part Repl. 0. 400 0.400 0.400 s

2. 1010.021 t1-Speed Gov. PI-Part Repl. 0. 200 0.200 0.200 s

2. 1010.040 Idle /End Gov.-Idle Speed 50 Hz 1400.0 1400.0 1400.0 rpm

Idle /End Gov.-End Speed 50

2. 1010.041 Hz 1600.0 1600.0 1600.0 rpm

2. 1010.042 Idle /End Gov.-Idle Speed 60 Hz 1700.0 1700.0 1700.0 rpm

Idle /End Gov.-End Speed 60

2. 1010.043 Hz 1900.0 1900.0 1900.0 rpm

Idle /End Gov.-Idle Speed

2. 1010.044 10.0 10.0 10.0 rpm/s
Ramp

Idle /End Gov.-End Speed

2. 1010.045 10.0 10.0 10.0 rpm/s
Ramp

2019-03-02 15:28 - 273048_HUYNH Page 12 of 22

C:\DiaSys\ECU_7\527111568 yangung1\527111568 yangung1 527111568 / Main
Single-parameters
ParNo Parameter PC-value Acti ve-value Startup-value Unit
2.8009.010 AL 2.8009.010 AL 2.8009.010 AL
2. 1050.001 Bin Out TOP1 PV-Number Combined Alarm Yel Combined Alarm Combined Alarm PV
(ECU) Yel (ECU) Yel (ECU)
2.8009.009 AL 2.8009.009 AL 2.8009.009 AL
2. 1050.002 Bin Out TOP2 PV-Number Combined Alarm Combined Alarm Combined Alarm PV
Red (ECU) Red (ECU) Red (ECU)
2.0100.902 SS 2.0100.902 SS 2.0100.902 SS
2. 1050.003 Bin Out TOP3 PV-Number PV
P-Lube Oil P-Lube Oil P-Lube Oil

2.1090.013 Starter 2.1090.013 2.1090.013

2. 1050.004 Bin Out TOP4 PV-Number PV
ON St arter ON Starter ON

2. 1050.005 Bin Out TOP1 Active Level

2. 1050.006 Bin Out TOP2 Active Level

2. 1050.007 Bin Out TOP3 Active Level

2. 1050.008 Bin Out TOP4 Active Level

2. 1050.009 Bin Out TOP Monitoring Config. 0 0 0 digit

2. 1050.010 TO P1 Low Sid e Switch

2. 1050.011 TO P2 Low Sid e Switch

2. 1050.012 TO P3 Low Sid e Switch

2. 1050.013 TO P4 Low Sid e Switch

2. 1050.014 TO P1 Select for Test

2. 1050.015 TO P2 Select for Test

2. 1050.016 TO P3 Select for Test

2. 1050.017 TO P4 Select for Test

2. 1051.990 Speed Window 1 Delay In 0. 000 0.000 0.000 s

2. 1051.991 Speed Window 2 Delay In 0. 000 0.000 0.000 s

2. 1051.992 Speed Window 1 Delay Out 0. 000 0.000 0.000 s

2. 1051.993 Speed Window 2 Delay Out 0. 000 0.000 0.000 s

2. 1051.994 Speed Window 1 Top 0.0 0. 0 0.0 rpm

2. 1051.995 Speed Window 1 Bottom 0.0 0. 0 0.0 rpm

2. 1051.996 Speed Window 1 Hysteresis 0.0 0. 0 0.0 rpm

2. 1051.997 Speed Window 2 Top 0.0 0. 0 0.0 rpm

2. 1051.998 Speed Window 2 Bottom 0.0 0. 0 0.0 rpm

2019-03-02 15:28 - 273048_HUYNH Page 13 of 22

C:\DiaSys\ECU_7\527111568 yangung1\527111568 yangung1 527111568 / Main
Single-parameters
ParNo Parameter PC-value Acti ve-value Startup-value Unit

2. 1051.999 Speed Window 2 Hysteresis 0.0 0. 0 0.0 rpm

1.0120.001 1.0120.001 1.0120.001

2. 1052.001 Analo g Out 1 PV-Number PV
T-Coolant T-Coolant T-Coolant

1.0100.001 P-Lube 1.0100.001 1.0100.001

2. 1052.002 Analo g Out 2 PV-Number P-Lube Oil after P-Lube Oil after PV
Oil after Filter
Filter Filter
2. 1052.003 Analo g Out 1 Scaling 0. 833 0.833 0.833 pts

2. 1052.004 Analo g Out 2 Scaling 0. 010 0.010 0.010 pts

2. 1052.005 Analo g Out 1 Of fset 0. 000 0.000 0.000 V

2. 1052.006 Analo g Out 2 Of fset 0. 000 0.000 0.000 V

2. 1055.002 FO Source PV Freq or Perio d Not used Not used Not used PV

2. 1055.003 FO Source PV Rat io Not used Not used Not used PV

SD-ReqEngSpeedDem . Def.
2. 1060.012 1000.0 1000.0 1000.0 rpm
Value
SD-ReqEngSp.Dem. Def.
2. 1060.013
Value Ac tive
Speed Dem SD-Monitoring
2. 1060.018
Suppression

2. 1060.031 SpeedDemand Monit. Delay 10.000 10.000 10.000 s

2. 1060.032 Delay Button Request-Change 0. 300 0.300 0.300 s

2. 1060.038 Rated Speed Genset 50Hz 1500.0 1500.0 1500.0 rpm

2. 1060.039 Rated Speed Genset 60Hz 1803.0 1803.0 1803.0 rpm

2. 1060.041 Rated Speed 1500.0 1500.0 1500.0 rpm

2. 1060.042 Engin e Speed Demand Min 600.0 600. 0 600.0 rpm

2. 1060.043 Engin e Speed Demand Max 1900.0 1900.0 1900.0 rpm

2. 1060.044 Engin e Speed Demand Min Eff 600.0 600. 0 600.0 rpm

Engin e Speed Demand Max

2. 1060.045 Eff 1978.0 1978.0 1978.0 rpm

2. 1060.046 Idle Inc rease Value (Start ) 0.0 0. 0 0.0 rpm

2. 1060.047 Durat ion of Idle Increase (Start) 0. 000 0.000 0.000 s

Requ. Engine Speed

2. 1060.055 Modif.Lim it 100.0 100. 0 100.0 rpm

2. 1060.090 DBR/MCR Speed Of fset 4. 000 4.000 4.000 %

2. 1060.091 DBR/MCR Delta Speed 35.0 35.0 35.0 rpm

2019-03-02 15:28 - 273048_HUYNH Page 14 of 22

C:\DiaSys\ECU_7\527111568 yangung1\527111568 yangung1 527111568 / Main
Single-parameters
ParNo Parameter PC-value Acti ve-value Startup-value Unit

2. 1060.092 DBR/MCR Delta Speed active

2. 1060.113 RampUp1 Speed Demand 200.0 200. 0 200.0 rpm/s

2. 1060.114 RampUp2 Speed Demand 200.0 200. 0 200.0 rpm/s

2. 1060.115 RampUp3 Speed Demand 200.0 200. 0 200.0 rpm/s

2. 1060.116 RampDown1 Speed Demand 200.0 200. 0 200.0 rpm/s

2. 1060.117 RampDown2 Speed Demand 200.0 200. 0 200.0 rpm/s

2. 1060.118 RampDown3 Speed Demand 200.0 200. 0 200.0 rpm/s

Ramp12Switc hPoint
2. 1060.119 SpeedDemand 3000.0 3000.0 3000.0 rpm

Ramp23Switc hPoint
2. 1060.120 3000.0 3000.0 3000.0 rpm
SpeedDemand

2. 1060.122 RampUp1 Up-Button 10.0 10.0 10.0 rpm/s

2. 1060.123 RampUp2 Up-Button 10.0 10.0 10.0 rpm/s

2. 1060.124 RampUp3 Up-Button 10.0 10.0 10.0 rpm/s

2. 1060.125 RampDown1 Down-Button 10.0 10.0 10.0 rpm/s

2. 1060.126 RampDown2 Down-Button 10.0 10.0 10.0 rpm/s

2. 1060.127 RampDown3 Down-Button 10.0 10.0 10.0 rpm/s

RampSwitc h12Point
2. 1060.128 UpDow nButton 3000.0 3000.0 3000.0 rpm

RampSwitc h23Point
2. 1060.129 3000.0 3000.0 3000.0 rpm
UpDow nButton
Local Normal Dem and Switch
2. 1060.150 Analo g rel. Analog rel. Analo g rel.
Default

Local Emergency
2. 1060.151 Up/Down But Up/Down But Up/Down But
DemandSwitc hDef ault
Remote Normal
2. 1060.152 Analo g rel. Analog rel. Analo g rel.
DemandSwitc h Default
Remote
2. 1060.153 EmergencyDemandSwitc hDef Up/Down But Up/Down But Up/Down But
ault
Dem. Switc hes only by
2. 1060.155 Parameters

2. 1060.202 Droop 4. 000 4.000 4.000 %

2. 1060.204 Droop2 4. 000 4.000 4.000 %

Torque Demand 60Hz (100%

2. 1060.209 0.0 0. 0 0.0 Nm
Load)

2. 1060.211 Frequency Sw itch active

2019-03-02 15:28 - 273048_HUYNH Page 15 of 22

C:\DiaSys\ECU_7\527111568 yangung1\527111568 yangung1 527111568 / Main
Single-parameters
ParNo Parameter PC-value Acti ve-value Startup-value Unit

Droop Sw itch with

2. 1060.214
const .Speed

2. 1060.215 Rated Speed if Droop 1 -> 2

2. 1060.216 Rated Speed if Droop 2 -> 1

2. 1060.217 Droop Sw itch active

2. 1060.300 Generator Mode Active

2. 1060.306 Genset Start Ramp 1 400.0 400. 0 400.0 rpm/s

2. 1060.307 Genset Start Ramp 2 400.0 400. 0 400.0 rpm/s

GensetSt artRamp
2. 1060.308 Sw itchPoint12 3000.0 3000.0 3000.0 rpm

2. 1060.309 Genset Idle Dela y 0. 000 0.000 0.000 s

Genset StartFinish
2. 1060.310 5.0 5. 0 5.0 rpm
Sync.Win dow

2. 1060.311 Delay Generat or On 2. 000 2.000 2.000 s

2. 1060.313 Sw itchPoint Generator OFF 800.0 800. 0 800.0 rpm

Frequency Sw itch via CAN

2. 1060.316 Sig nal

Genset StartRamp with P-Oil

2. 1060.319 Control

2. 1060.320 Speed Demand Increase Valu e 1000.0 1000.0 1000.0 rpm

2. 1060.330 Genset Quick Start Ramp 1 50.0 50.0 50.0 rpm/s

2. 1060.331 Genset Quick Start Ramp 2 50.0 50.0 50.0 rpm/s

Request Idle Speed On Ramp

2. 1060.417 10.0 10.0 10.0 rpm/s
2

Requ.Idle Sp. RampSwitch

2. 1060.418 50.0 50.0 50.0 rpm
P.(Of fset)

2. 1060.422 Request Idle Speed On Ramp 50.0 50.0 50.0 rpm/s

Speed Demand Limitation

2. 1060.430 Value 800.0 800. 0 800.0 rpm

Speed Demand Limitation

2. 1060.431 Ramp 200.0 200. 0 200.0 rpm/s

Speed Demand Limit. Off

2. 1060.432 Ramp 200.0 200. 0 200.0 rpm/s

2. 1075.009 Ratin g Select. via CAN

2. 1075.010 Select Ratin g Valu e 0 0 0 digit

Enable Internal Start

2. 1090.100
Proc edure

2019-03-02 15:28 - 273048_HUYNH Page 16 of 22

C:\DiaSys\ECU_7\527111568 yangung1\527111568 yangung1 527111568 / Main
Single-parameters
ParNo Parameter PC-value Acti ve-value Startup-value Unit

2. 1090.101 Start Signal Stored

2. 1090.102 Stop Resets Loc k Time

2. 1090.104 Enable Manual Prelubrication

2. 1090.105 Enable Manual Turning

Coolant Alarm Suppression

2. 1090.106 /EngStop

2. 1090.107 Enable Intermittent Oil Primin g

2. 1090.131 Requested Starter Speed 80.0 80.0 80.0 rpm

2. 1090.132 Starter Time Interval 1. 500 1.500 1.500 s

2. 1090.133 Starter Pause 5. 000 5.000 5.000 s

2. 1090.134 Number of Starting Attem pts 3 3 3 digit

2. 1090.135 Starter Rele as e Speed 300.0 300. 0 300.0 rpm

2. 1090.136 Starter Rele as e Time Interval 10.000 10.000 10.000 s

2. 1090.137 Idle Speed Time Interval 10.000 10.000 10.000 s

2. 1090.138 Restart Lock Time Af ter Stop 5. 000 5.000 5.000 s

2. 1090.142 Prelu brication Period 0. 000 0.000 0.000 s

Maximum Manual Turning

2. 1090.144 Perio d 5. 000 5.000 5.000 s

2. 1090.150 Prelu brication Interval 60 60 60 min

2. 1090.151 P-LubeOil Prelubrication Limit 0. 20000 0.20000 0.20000 bar

2. 1090.155 P-LubeOil PreLube Ala rm Limit 0. 00000 0.00000 0.00000 bar

Time to PreLube Ala rm

2. 1090.156 0. 000 0.000 0.000 s
Pres sure

2. 1090.157 T-LubeOil PreLube Ala rm Limit 0.00 0.00 0. 00 degC

Maximum Prelubricatio n
2. 1090.159 Perio d 300. 000 300.000 300.000 s

2. 1090.303 T-Preheat L1 Input Valu e 15.00 15.00 15.00 degC

2. 1090.304 T-Preheat L1 Hysteresis 1.00 1.00 1. 00 degC

2. 1090.305 T-Preheat L2 Input Valu e 0.00 0.00 0. 00 degC

2. 1090.306 T-Preheat L2 Hysteresis 1.00 1.00 1. 00 degC

2019-03-02 15:28 - 273048_HUYNH Page 17 of 22

C:\DiaSys\ECU_7\527111568 yangung1\527111568 yangung1 527111568 / Main
Single-parameters
ParNo Parameter PC-value Acti ve-value Startup-value Unit

2. 1090.307 T-Preheat L2 Aborts Start

2. 1090.308 T-Preheat L2 Override Possib le

Preheat Intercool.Monitoring
2. 1090.310
ac tive

Func. Startlo ck Stored Al.

2. 1090.402
ac tive

2. 1090.460 P-Startoil Monitorin g activet ed

2. 1090.461 Limit St artoilp ressure 0. 40000 0.40000 0.40000 bar

Max. P-Startoil Monit oring

2. 1090.462 Perio d 10.000 10.000 10.000 s

2. 1090.465 Functio n Quick Start active

2. 2500.027 Limit Engine Speed Low 0.0 0. 0 0.0 rpm

2. 2510.001 Test Overspeed Activ. Speed 1650.0 1650.0 1650.0 rpm

Test Overspeed Activ. Speed

2. 2510.002 250.0 250. 0 250.0 rpm
Hyst.

2. 2510.003 Test Overspeed Limit Factor 0. 000 0.000 0.000 %

2. 2510.004 Test Overspeed Method

Test Overspeed without Local

2. 2510.005 Sig nal

2. 2700.010 T-Coolant FanControl LL 85.00 85.00 85.00 degC

2. 2700.011 T-Coolant FanControl UL 120.00 120.00 120. 00 degC

2. 2700.020 T-ChargeAir FanControl LL 45.00 45.00 45.00 degC

2. 2700.021 T-ChargeAir FanControl UL 85.00 85.00 85.00 degC

2. 2700.030 T-LubeOil FanControl LL 80.00 80.00 80.00 degC

2. 2700.031 T-LubeOil Fan Control UL 115.00 115.00 115. 00 degC

2. 2700.040 T-Cool-InterCooler FanCt rl LL 45.00 45.00 45.00 degC

2. 2700.041 T-Cool-InterCooler FanCt rl UL 60.00 60.00 60.00 degC

2. 3000.032 Ignore Cyl Cutout Suppress ion

2. 4000.001 Lif eDat a Functio n

2. 4000.003 Lif eDat a Fail Delay 600. 000 600.000 600.000 s

2. 7001.009 Stop Signal St ored

2019-03-02 15:28 - 273048_HUYNH Page 18 of 22

C:\DiaSys\ECU_7\527111568 yangung1\527111568 yangung1 527111568 / Main
Single-parameters
ParNo Parameter PC-value Acti ve-value Startup-value Unit

2. 7001.031 Stop SD T-Coolant activated

2. 7001.032 Stop SD T-Charge Air ac tivated

2. 7001.033 Stop SD T-Oil activat ed

2. 7001.034 Stop SD P-Oil activat ed

2. 7001.035 Stop SD P-Fuel activated

2. 7001.037 Stop SD Cool.Level activated

2. 7001.201 Func. Cool-Down Time active

2. 7002.005 Durat ion of Override 0. 000 0.000 0.000 s

2. 7002.006 Overrid e Mode 1 1 1 digit

2. 7002.009 Set Alarm in cas e of Overrid e

2. 7003.002 Mode 2 Def ault Ac tive

Red AND Yel Combined

2. 8009.001
Ala rms

2. 8009.030 FuelCons . CAN active

2. 9900.001 ECU AI 1 Current-Mode

2. 9900.011 ECU AI 2 Current-Mode

2. 9901.200 Sens ortype Input AI1 24 24 24 digit

2. 9901.201 Sens ortype Input AI2 -1 -1 -1 digit

2. 9902.001 Monitor Open Load DI1

2. 9902.011 Monitor Open Load DI2

2. 9902.021 Monitor Open Load DI3

2. 9902.031 Monitor Open Load DI4

2. 9902.041 Monitor Open Load DI5

2. 9902.051 Monitor Open Load DI6

2. 9902.061 Monitor Open Load DI7

2. 9902.071 Monitor Open Load DI8

2. 9902.081 Monitor Open Load ESI

2019-03-02 15:28 - 273048_HUYNH Page 19 of 22

C:\DiaSys\ECU_7\527111568 yangung1\527111568 yangung1 527111568 / Main
Single-parameters
ParNo Parameter PC-value Acti ve-value Startup-value Unit

2.7001.002 Stop 2.7001.002 Stop 2.7001.002 Stop

2. 9910.001 Bin -Input 0 Target PV Number PV
Button Button Button

2. 9910.002 Bin -Input 0 Bouncing Time 0. 050 0.050 0.050 s

2. 9910.003 Bin -Input 0 SD Delay 0. 100 0.100 0.100 s

2. 9910.004 Bin -Input 0 Module Act ive

2. 9910.005 Bin -Input 0 Ac tive High

2. 9910.006 Bin -Input 0 Default Value

2. 9910.007 Bin -Input 0 Input Channel DI 1 DI 1 DI 1

2.1060.062 Ext. 2.1060.062 Ext. 2.1060.062 Ext.

2. 9910.011 Bin -Input 1 Target PV Number Demand Swit ch Demand Switch Demand Swit ch PV
Analo g / UpDow n Analog / UpDow n Analo g / UpDow n
2. 9910.012 Bin -Input 1 Bouncing Time 0. 050 0.050 0.050 s

2. 9910.013 Bin -Input 1 SD Delay 0. 100 0.100 0.100 s

2. 9910.014 Bin -Input 1 Module Act ive

2. 9910.015 Bin -Input 1 Ac tive High

2. 9910.016 Bin -Input 1 Default Value

2. 9910.017 Bin -Input 1 Input Channel DI 2 DI 2 DI 2

2.1060.428 Binary 2.1060.428 2.1060.428

2. 9910.021 Bin -Input 2 Target PV Number Speed Limitation Binary Speed Bin ary Speed PV
Ac tive Limitatio n Active Limit ation Active
2. 9910.022 Bin -Input 2 Bouncing Time 0. 050 0.050 0.050 s

2. 9910.023 Bin -Input 2 SD Delay 0. 100 0.100 0.100 s

2. 9910.024 Bin -Input 2 Module Act ive

2. 9910.025 Bin -Input 2 Ac tive High

2. 9910.026 Bin -Input 2 Default Value

2. 9910.027 Bin -Input 2 Input Channel DI 3 DI 3 DI 3

2.8009.021 DIx 2.8009.021 DIx 2.8009.021 DIx

2. 9910.031 Bin -Input 3 Target PV Number Request Alarm Reset Request Alarm Request Alarm PV
Reset Reset
2. 9910.032 Bin -Input 3 Bouncing Time 0. 050 0.050 0.050 s

2. 9910.033 Bin -Input 3 SD Delay 0. 100 0.100 0.100 s

2. 9910.034 Bin -Input 3 Module Act ive

2. 9910.035 Bin -Input 3 Ac tive High

2019-03-02 15:28 - 273048_HUYNH Page 20 of 22

C:\DiaSys\ECU_7\527111568 yangung1\527111568 yangung1 527111568 / Main
Single-parameters
ParNo Parameter PC-value Acti ve-value Startup-value Unit

2. 9910.036 Bin -Input 3 Default Value

2. 9910.037 Bin -Input 3 Input Channel DI 4 DI 4 DI 4

2.1060.026 Up 2.1060.026 Up 2.1060.026 Up

2. 9910.041 Bin -Input 4 PV Number PV
Button ECU Button ECU Button ECU

2. 9910.042 Bin -Input 4 Bouncing Time 0. 050 0.050 0.050 s

2. 9910.043 Bin -Input 4 SD Delay 0. 100 0.100 0.100 s

2. 9910.044 Bin -Input 4 Module Act ive

2. 9910.045 Bin -Input 4 Ac tive High

2. 9910.046 Bin -Input 4 Default Value

2. 9910.047 Bin -Input 4 Input Channel DI 5 DI 5 DI 5

2.1060.027 Down 2.1060.027 2.1060.027

2. 9910.051 Bin -Input 5 Target PV Number Down Button Down Button PV
Button ECU
ECU ECU
2. 9910.052 Bin -Input 5 Bouncing Time 0. 050 0.050 0.050 s

2. 9910.053 Bin -Input 5 SD Delay 0. 100 0.100 0.100 s

2. 9910.054 Bin -Input 5 Module Act ive

2. 9910.055 Bin -Input 5 Ac tive High

2. 9910.056 Bin -Input 5 Default Value

2. 9910.057 Bin -Input 5 Input Channel DI 6 DI 6 DI 6

2.1090.051 Engin e 2.1090.051 2.1090.051

2. 9910.061 Bin -Input 6 Target PV Number Engine Start Engin e Start PV
Start Butt on
Button Button
2. 9910.062 Bin -Input 6 Bouncing Time 0. 050 0.050 0.050 s

2. 9910.063 Bin -Input 6 SD Delay 0. 100 0.100 0.100 s

2. 9910.064 Bin -Input 6 Module Act ive

2. 9910.065 Bin -Input 6 Ac tive High

2. 9910.066 Bin -Input 6 Default Value

2. 9910.067 Bin -Input 6 Input Channel DI 7 DI 7 DI 7

2.7002.001 Override 2.7002.001 2.7002.001

2. 9910.071 Bin -Input 7 Target PV Number Button Overrid e Butt on Overrid e Button PV

2. 9910.072 Bin -Input 7 Bouncing Time 0. 050 0.050 0.050 s

2. 9910.073 Bin -Input 7 SD Delay 0. 100 0.100 0.100 s

2019-03-02 15:28 - 273048_HUYNH Page 21 of 22

C:\DiaSys\ECU_7\527111568 yangung1\527111568 yangung1 527111568 / Main
Single-parameters
ParNo Parameter PC-value Acti ve-value Startup-value Unit

2. 9910.074 Bin -Input 7 Module Act ive

2. 9910.075 Bin -Input 7 Ac tive High

2. 9910.076 Bin -Input 7 Default Value

2. 9910.077 Bin -Input 7 Input Channel DI 8 DI 8 DI 8

2.1090.001 Ignition 2.1090.001 2.1090.001

2. 9910.091 Bin -Input 9 Target PV Number input IGI ac tivated Ignition input IGI Ignition in put IGI PV
ac tivated ac tivated
2. 9910.092 Bin -Input 9 Bouncing Time 0. 050 0.050 0.050 s

2. 9910.093 Bin -Input 9 SD Delay 0. 100 0.100 0.100 s

2. 9910.094 Bin -Input 9 Module Act ive

2. 9910.095 Bin -Input 9 Ac tive High

2. 9910.096 Bin -Input 9 Default Value

2019-03-02 15:28 - 273048_HUYNH Page 22 of 22