SOME ITEMS NEEDED.

1; VENTILATOR MACHINE.( atleast 2 items)

SPECIFICATIONS.
 Physical Specification.
-Dimensions at least 300mmx300mmx250mm.
-Display Resolution (H) x (V) at least 1200x800 pixel
-Screen 12.1 colors active with touch screen.
-Adjustable Brightness

 Ventilation Specifications;
-Able to perform for adult, paediatric and neonatal

 Functions:
-perform oxygen therapy
-able to perform nebulization
-perform non invasive and invasive ventilation
-difference alarm systems

 Ventilation Mode;
-V-A/C (Volume assist/control)
-P-A/C (Pressure assist/control)
-V-SIMV (Volume - Synchronized Intermittent Mandatory Ventilation)
-P-SIMV (Pressure - Synchronized Intermittent Mandatory Ventilation)
-Duo Level (Duo Level Ventilation)
-CPAP (Continuous Positive Airway Pressure)
-PSV (Pressure Support Ventilation)
-APRV (Airway Pressure Release Ventilation)
-PRVC-SIMV (Pressure Regulated Volume Control-Synchronized
Intermittent -Mandatory Ventilation)
-AMV (Adaptive Minute Ventilation)
-NIV (Non-invasive Ventilation)
-Apnea Ventilation

 Environmental specifications:
-Temperature; 5 - 40 °C (operating); -20 to 60 °C (storage and transport,
O2 sensor: -20 to 50°C)
-Relative humidity; 10 - 95 % (operating); 10 - 95 % (storage and transport)
-Barometric pressure; 62 - 106 kPa (operating); 50 -106 kPa (storage and
transport)
 External AC power supply
-Input voltage; 100 - 240 V
-Input frequency; 50/60 Hz
-Input current; 2.7 - 1.1 A
-Fuse; T3.15 AH/250 V

 External DC power supply

Voltage 12V
Current 15A
 Rechargeable Battery(batteries)
-Able to run at least 360 min (Powered by fully - charged battery in
standard working condition)
 Trolley/ventilator carrier
-dimensions at least 1030mmx500mmx500mm
-weight approximately 20kgs

SUGGESTED BLAND AND MODE; HAMILTON, C6 SERIES or MINDRAY,

SV300 PRO

2; CARDIAC MONITOR SPECIFICATIONS:( atleast 5 items)

 physical specifications:
-Weight; 3-5kgs (excluded battery and accessories)
-dimensions at least 300mmx220mmx190mm
-display size at least 1200x800pixel with mult operation touch screen
- Up to 8 waveforms or more

 ECG.
-Meet standards of IEC 60601-2-27 and IEC 60601-2-25.
-Lead set 3-lead: I, II, III
5-lead: I, II, III, aVR, aVL, aVF, V
12-lead: I, II, III, aVR, aVL, aVF, V1 to V6
-Automatic 3/5/6/12 - lead recognition.
-Input signal range ± 10 mV (p-p)
-Electrode offset potential tolerance ± 800 mV
-Sweep speed 6.25 mm/s, 12.5 mm/s, 25 mm/s, 50 mm/s
-Waveform format Standard, Cabrera
-Bandwidth Diagnostic mode: 0.05 to 150 Hz
-Monitor mode: 0.5 to 40 Hz
-Surgical mode: 1 to 20 Hz
-ST mode: 0.05 to 40 Hz
 -CMRR Diagnostic mode: > 90 dB
-Monitor, Surgical, ST mode: > 105 dB
-Pace detection Amplitude: ± 2 mV to ± 700 mV
-Width: 0.1 to 2 ms
-Rise time: 10 to 100 μs
-Defib. Protection Withstand 5000V (360J) defibrillation
-Recovery time <5 s

 Non invasive blood pressure (NIBP).

-Meet standards of ISO 80601-2-30.
-Technique Oscillometry
-Operation mode Manual, Auto, STAT, Sequence
-Parameters Systolic, diastolic, mean
-Max measurement time Adult/Pediatric: 180 s, Neonate: 90 s
-Systolic range Adult: 25 to 290 mmHg, Pediatric: 25 to 240 mmHg,
Neonate: 25 to 140 mmHg
-Diastolic range Adult: 10 to 250 mmHg ,Pediatric: 10 to 200
mmHg,-Neonate: 10 to 115 mmHg
-Mean range Adult: 15 to 260 mmHg, Pediatric: 15 to 215 mmHg, Neonate:
15 to 125 mmHg
-NIBP accuracy Max mean error: ± 5 mmHg
-Max standard deviation: 8 mmHg
-NIBP resolution 1 mmHg.

 Invasive blood pressure.

-Meet standard of IEC 60601-2-34.
-Channels 2 channels
-Sensitivity 5 μV/V/mmHg
-Impedance range 300 to 3000 Ω
-IBP range -50 to 360 mmHg
-ICP measurement Support
-Support waveforms overlapping.

 Heart rate.
-HR range Adult: 15 to 300 bpm
-Pediatric/Neonate: 15 to 350 bpm
-HR resolution 1 bpm

 Arrhythmia analysis
-Intended use for adult, pediatric and neonate.
-Multi-lead, 25 classifications. Asystole, VFib/VTac, Vtac, Vent. Brady,
Extreme Tachy, Extreme Brady, Vrhythm, PVCs/min, Pauses/min, Couplet,
Bigeminy, Trigeminy, R on T, Run PVCs, PVC, Tachy, Brady, Missed Beats,
PNP, PNC, Multif. PVC, Nonsus. Vtac, Pause, Irr. Rhythm., Afib (for adult
 only).
 Respiration.
-Lead I or II, auto
-RR range 0 to 200 rpm
-RR accuracy ± 1 rpm (0 to 120 rpm)
-RR resolution 1 rpm
-Sweep speed 3 mm/s, 6.25 mm/s, 12.5 mm/s, 25 mm/s,
50 mm/s
-Apnea time 10 s, 15 s, 20 s, 25 s, 30 s, 35 s, 40 s

 spo2
-Meet standards of ISO 80601-2-61.
-SpO2 range 0 to 100 %
-Perfusion indicator
-refreshing rate ≤ 1 s

 pulse rate
-PR range 20 to 300 bpm (from SpO2), 20 to 350 bpm (from IBP), 30 to
300 bpm (from NIBP)
Refreshing rate ≤ 1 s

 temperature
-Meet standard of ISO 80601-2-56.
-Technique Thermal resistance
-Channels 2 channels
-Temp range 0 to 50 °C (32 to 122 °F)
Refreshing rate ≤ 1 s

 alarms
-Audio/voice alarming.
-video/light alarming.
-Provide Alarm Sight info graphic alarm indicator.

 interfacing and connectivity

-Main unit AC power connector (1)
- VGA port at least 1.
-Network connector (1), RJ45
-USB 2.0 at least 2 ports
-Analog output/nurse call/defib. Sync. Port (1)
-Equipotential grounding terminal (1)
-DC-in connector.
-Barcode scanner Support 1D and 2D barcode
-Remote control Support
-Thermal recorder 3 traces (paper 50 mm width, 20 m length)
 -Network printer Support

 power
-Line voltage 100 to 240 VAC (±10 %)
-Maximum current 2.0A
-Frequency 50/60 Hz (±3 Hz)
-Battery Rechargeable lithium-ion battery, 2600mAh/4500mAh
Rechargeable smart lithium-ion battery 5600mAh

 Environment requirement.
-Temperature Operating: 0 to 40 °C , Storage: -30 to 70 °C, Storage: -20 to
60 °C,
-Humidity Operating: 15 to 95 % (non condensing) Storage: 10 to 95 %
(non condensing)
-Barometric Operating: 427.5 to 805.5 mmHg (57 to 107.4 kPa) Storage:
120 to 805.5 mmHg (16 to 107.4 kPa)

SUGGESTED BRAND AND MODE; MINDRAY, BENEVISION uMEC 150.

3; INFUSION PUMP MACHINE.(atleast 5 items)

 physical specifications;
-Dimensions at least (WxHxD) 250x90x150mm
-Net weight not more than 4kgs

 display
-Screen 3.5 TFT color
-Adjustable brightness
-information to be displayed on screen a)delivery rate of infusion,
b)current infusion, c)volume to be infused(VTBI), d) IV set brand,
e)pressure limit, f)battery capacity, g)drug name h)remaining time i)
alarms.

 cpu type -dual CPU

 Infusion set.
-Automatically recognition of infusion set brand after calibration.
-Automatically and manual bolus delivery

 Functional spectrum.
-Automatic calculation of the delivery rate based on different modes
 -infusion pause/standby while present parameters remain stored.
-drug library at least up to 1500 drug names.
-History record up to 2000.
- Able to transmit data to computerized materials

 Safety systems.
-Detection of occlusion pressure and automatic stop infusion.
-air detection
-multi bubble or single bubble detection

 Battery.
-Rechargeable
-Able to work at least 180minutes out from power source.
-At least 4500mAh battery capacity.

SUGGESTED BRAND AND MODE; MINDRAY, BENEFUSION SP5 series

4; SYRINGE PUMP MACHINE( atleast 5 items)

 physical specifications;
-Dimensions at least (WxHxD) 250x90x150mm
-Net weight not more than 4kgs

 display
-Screen 3.5 TFT color
-Adjustable brightness
-information to be displayed on screen a)delivery rate of infusion,
b)current infusion, c)volume to be infused(VTBI), d) IV set brand,
e)pressure limit, f)battery capacity, g)drug name h)remaining time i)
alarms.

 cpu type -dual CPU

 Infusion set.
-Automatically recognition of infusion set brand after calibration.
-Automatically and manual bolus delivery

 Functional spectrum.
- Able to operate with all size of syringes while Syringe 5 ml: 0.1-100 ml/h
(in 0.01, 0.1, 1, 10 ml/h increments), Syringe 10 ml: 0.1-300 ml/h, Syringe
20 ml: 0.1-600 ml/h, Syringe 30, ml: 0.1-800 ml/h, Syringe 50/60 ml:
0.1-1200 ml/h
-Automatic calculation of the delivery rate based on different modes
 -Syringe pumping pause/standby while present parameters remain stored.
-drug library at least up to 1500 drug names.
-History record up to 2000.
- Able to transmit data to computerized materials

 Safety systems.
-Detection of occlusion pressure and automatic stop infusion.
-air detection
-multi bubble or single bubble detection

 Battery.
-Rechargeable
-Able to work at least 180minutes out from power source.
-At least 4500mAh battery capacity.
SUGGESTED BRAND AND MODE; MINDRAY, BENEFUSION SP5 series
syringe pump

5; ELECTROCARDIOGRAM (ECG) MACHINE.(atleast 1 item)

 Physical specifications;
-Size & Weight, Sturdy & light weight machine less than 5kgs
- Should have carry handle for portability
- Should be compact
 Power Supply
- Compatibility with mains 220-240 V (normal), 50/60 Hz power supply
- High performance Li-ion rechargeable battery with builtin charger.
-Equipment should have sufficient battery backup for taking minimum 100
ECGs without AC power.
- Digital filtering to remove interference from power line, muscle tremor
etc

 ECG recording
- ECG recording with 12 leads
- Standard Leads (the limb leads or bipolar Limb leads: I, II & III).
Augmented Limb Leads a. Standard Leads (the limb leads or bipolar Limb
leads: I, II & III) , Augmented Limb Leads- (aVL, aVR and aVF) AND Chest
Leads ( the unipolar or V leads)- from V1 to V6 Simultaneous.
- Recording speed selection of 25 mm/ sec and 50 mm/ sec with facility
for speed selection
- Automatic adjustment of baseline for optimal recording
- Should have different filters like Baseline Filter, EMG Filter & AC Filter
- Multiple operating modes -automatic, manual and rhythm

 Built-in ECG Parameters measurement and interpretation

 - -Built-in ECG auto-measurement including: HR, P-R interval, P-Duration,
QRS duration, Q-T interval, Q-TcF (Friedericia), P Axis, QRS Axis, T Axis,
R(V5), S(V1), R(V5)+S(V1).

 Printing and Communication

-High-resolution thermal printing array system
-Built in printer should work with standard universal thermal printer paper

 Standard Accessories
- The machine should be supplied with power cord , patient cable, user
manual and warranty card, Operation Manual with user demonstration
video CD, interpretation manual & 10 thermal recording paper rolls , and at
least 5 bottles of jelly
- And but not limit with Two sets each of: patient cable, chest electrodes
– Both adult and paediatric (2 sets each), limb electrodes – Both adult
and paediatric (2 sets each)

 Safety Profile
- Should be provided with terminal for good earth connection to preclude
electric disturbances while recording
- Must have a safety certificate or valid detailed electrical and functional
safety test report from a recognized competent authority
- Copy of the certificate / test report shall be produced along with the
technical bid.
SUGGESTED BRAND AND MODE; MINDRAY, BENEHEART R12

6; MOBILE/PORTABLE ULTRASOUND MACHINE.( 1 item)

 Functions specifications.
-The equipment must be capable of operating in B, M, Doppler, Color flow
and Power Doppler modes
- The machine include at least a 19" LCD monitor for both excellent
images viewing as well as providing for workflow and productivity
features
- The LCD monitor mounted on an articulating arm that moves side-to-side,
forward and backward.
- The machine includes a minimum 10 inch Touch-screen LCD with
context sensitive menus to facilitate productivity.
- The system have minimum three universal active probe Ports in a
convenient, easy to access location to maximize the availability of needed
probes, with pin less connector.
- Ability to store images by patient and include the ability to review images
from different exam dates.
 -support the ability to store digital data in complete Raw Form, that allows
to optimize imaging parameters such as B Gain, Dynamic Range, Speckle
Reduction levels, Doppler Gain, Doppler Base Line on old Images & old
loops recalled from the image archive.
- allow for live image and archive images side-by-side or quad display on a
single monitor. This display allows any type of image – B-Mode, Color, or
power Doppler on either side.
- Automatically invoke the correct mode and imaging parameter and
advance to the next step within the examination with a one-bottom
operation. Contrast Ultrasound Capability (CEUS) with Times Intensity
Curve Graphs.
- provide a display zoom function on frozen images.

 Physical specificitaions
-should be portable with flexible wheels with locks
-Dimension size at least 35x35x7cm
-Net weight <10kgs
-12 LED screen.

 Rechargable battery
- At least 8000mAh built in battery that continue scanning at least 3 hours
without power.
 Uses of optinal probe in single active universal port.
-linear probe
-curved probe
-pediatric probe
-cardiac probe.
 Output interface
-USB Video output
-SVGA Video output
-PAL Video output.
SUGGESTED BRAND AND NAME: MINDRAY,ME8 ULTRASOUND

7; AUTOMATED DEFIBRILLATOR MACHINE( 1 item)

 Physical specifications.
-ECG Monitoring optional button
-CPR monitoring optional button
-manual mode button
-Self test mode button.
-beside printing optional
-dimensional size of screen at least 220x300 pixels
 Shock Sequence.
-Constant or escalating, Programmable (factory settings).
  Functions
-Adult and pediatric settings. For pediatric 50j (Average for 50 Ω at low
level energy), 75j (Average for 50 Ω at high level energy). For adult
170j (Average for 50 Ω at low level energy), 270j (Average for 50 Ω at
high level energy)
-Biphasic output waveform
-Automatic ECG (VT/VF) detection and analysis.
-Automatic impedance compensation based on patient.
-PaediatricsPaediatric dose attenuation.
-Automatic switch between AED and CPR modes based on analysis

 Battery
-Rechargeable, Battery type LiSO2 or LiM no (depending on the model
supplied).
-The internal battery, when full supports at least 140 full discharges at
200J, or two hours continuous ECG monitoring.

 Environmental conditions.
-Operating conditions: 0°C - 50°C
- Storage conditions: -10°C - 50°C
SUGGESTED BRAND AND MODE; MINDRAY, BENEHEART D3

8. ARTERIAL BLOOD GAS ANALYSER MACHINE(ABG MACHINE)(atleast 2

item)

 Physical specifications.
-Bar code scanning for cartridge insertion
-User Input button or Keyboard or screen touch
-USB port for data transfer
-Cartridge insertion port
-Attached or separated printer for scanning and print results
-screen size at least 10x10cm
-Dimension < 25x10x5cm

 Functional specifications,
-Able to perform blood gases, chemistry, electrolytes and hematology
tests.
-Multi-parameter card Single-use test card offer a broad menu of tests
on a single, portable platform. Each test card has a unique
combination of biosensors to suit a wide range of clinical needs.
-Analysis Time less that 2 min
-Calibration every sample
 Built in battery that may perform at least 3 hours out from power source.
 Sample
-Arterial or venous whole blood in either 1-10cc syringe.

SUGGESTED BRAND AND NAME: ABBORT, iSTAT 1 ABG machine

9. ICU ELECTRIC PATIENT BED.( atleast 5 items)

 Physical specifications.
-4 rails, 2 at top, left and right and 2 at bottom, left and right
-size dimensional at least 210cm length, 100cm width and 60cm
height.
-Material, plastic mixed with Mild Steel
-Number Of Wheels 4.
-Mattress size may correspond with mentioned bed size.
-working load at least 250kg.
-IV pole 4 hooks/drip stand pole, one in each corner of the
bed
- At least 2 Drainage/urinary bag hook left and right side of
the bed.
- Has degree angle indicator.
-Has auto weighing measure.

 Functions specifications.
-using remote control and built-in button control to perform.
-perform height adjustment, backrest, footrest, Trendelenburg, and
anti-Trendelenburg.
-Has cardiac set and CPR set to quick cardiac arrest performance
-Head Elevation up to 0~85°
-Knee Elevation up to 0~32°
-Auto-chair
-Outer / Inner Siderail Controls
-Normal Lockable Castor
-Volts & Frequency AC100 ~ 240V ； 50 / 60 Hz

 Built-in battery able to last at least 3 hour out from source of power

SUGGESTED BRAND AND MODE; Electric icu bed DA-2.

10. VIDEO LARYNGOSCOPE( atleast 1 item)

 Physical specifications.
 -Monitor Size: 3 Inch
-Video Aspect Ratio: 4:3
-Power: 3.7VDC
-Internal Memory: 16G TF Card
-Rotation Angle: Multi-rotational display
-Rechargeable Battery
-Camera Chip: CMOS
-Light Source: White LED
-Video Resolution at least 320 x 240 (QVGA) pixels per frame
-Video Screen: OLED Display
-Video Screen at least Size 6.096cm / 2.4" diagonal

 Functions specifications
-Able to apply to Adult and Neonatal.
-Attached Adult baton with disposable Mac Blades of size 2, 3, 4.
-Attached Neonatal baton with disposable Miller Blades of size 0, 00,
1.
-Computerized Power Management System: Auto Shut off, Auto white
balancing.
-Portability of hand-held video laryngoscope.

 Battery.
-Batteries: 3AAA
-Battery Life: <90 min. (confirm with Power Indicator status)

SUGGESTED BRAND AND MODE: VIDEO LARYNGOSCOPE VLM432.

11. PORTABLE VEIN FINDER MACHINE.(atleast 1 item)

 Physical specifications.

-High resolution imaging

-5 color modes for different skin tones

-3 projection sizes

-Long life rechargeable battery

-length <10cm width< 5cm height <5cm

 Attachment
 - should has Vein Viewer

-Should has Charging Station

- should has Power Adapter

-should has User Manual

 Functions specifications.

-Infrared vein finder for vein localization

-Colored vein visualization in real time

-Five projection colors and inverse color mode for every color

-With depth detection of veins

-Different select-able brightness levels and projection window

sizes

 Technical specifications.

-Light Type: Near-infrared light

-Infrared Wavelengths: 850 nm

-Image Resolution: 720 x 480

-Visible Vein Size at least ≥ 1 mm

-Depth of Visible Vein at least ≤ 12 mm

-Best Projection Distance at least 200 ± 20 mm

-Image Frame Rate at least 20 FPS

-LED Lifetime at least 20,000 hours

-Power Supply DC 5V ≤ 3.5W

-Weight <450 g
 -Dimensions: 240 mm x 60 x 60 mm

-Battery Volume at least 4400m AH and Battery Working Time

at least 5 hours

-Charging Time not more than 3 hours.

SUGGESTED BRAND AND MODE; Portable Vein Finder NEU260