Scribd Logo
Upload

Welcome to Scribd!

  • 5 views

    TLE 9 ICT Final Examination

    Uploaded by

    makernids

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    TLE 9 ICT Final Examination

    Uploaded by

    makernids
    5 views1 page

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    5 views1 page

    TLE 9 ICT Final Examination

    Uploaded by

    makernids

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    Dujali National High School

    Final Examination in ICT 9


    Name________________________________
    Grade Level and Section: __________________________________

    A. Direction. Write TRUE if the statement is correct and FALSE if it is wrong.


    _______ 1. Selecting the best tool for each task requires training in the proper use of
    the tools, field experience in their safe use, and following the manufacturer’s
    guidance and instructions for that specific tool.
    _______ 2. When obtaining the tool, all the associated tooling and consumable parts,
    as recommended by the manufacturer, must be included.
    _______ 3. The safe use of a tool depends on using the tool for the purpose for which it
    was designed and also for other purposes where it can be used as
    substitute where tool is not available.
    _______ 4. All tools should be kept in good condition with regular maintenance.
    _______ 5. Preparing for a task includes only knowing the task to be done.
    _______ 6. Preparing for a task includes also the sequence of tasks to be done.

    B. Direction. Select the letter of the correct answer. Write your answers on a separate
    sheet of paper.
    1. Which tool is used for hardware to stand on to prevent static electricity from building
    up?
    a. Anti-static mat c. Philips head screwdriver
    b. Hex driver d. Wire cutter
    2. Which tool is used to loosen or tighten cross-head screws?
    a. Anti-static mat c. Philips head screwdriver
    b. Hex driver d. Wire cutter
    3. Which tool is sometimes called a nut driver? It is used to tighten nuts in the same
    way that a screwdriver tightens screws?
    a. Anti-static mat c. Philips head screwdriver
    b. Hex driver d. Wire cutter
    4. Which tool is used to strip and cut wires?
    a. Anti-static mat c. Philips head screwdriver
    b. Hex driver d. Wire cutter
    5. Which tool is used to retrieve parts from location that are too small for your hand to
    fit?
    a. Part Retriever c. Cable ties
    b. Lint-free Cloth d. Flat head screwdriver

    C. Direction. Match items on Column A with Column B.

    _____1. A ma gnetic storage device that is installed inside the computer. A. Registers
    _____2. Early drive controller interface that connects computers
    and hard disk drives which an interface that uses a 40-pin connector. B. Flash drive or Thumb drive
    _____3. Tem porary storage for data and programs that are being
    accessed by the CPU. C. Read-only
    memory
    _____4. A sto rage device that uses lasers to read data on the
    optical media. D. IDE
    _____5. A sto rage device that uses removable 3.5-inch disks. E. Floppy drive
    _____6. Sold ered the memory chips on a special circuit board. F. Random access
    memory
    _____7. A rem ovable storage device that connects to a USB port. G. Optical drive
    _____8. Chip s that are located on the motherboard. H. DDR
    _____9. Mem ory cells built right into the CPU that contain
    specific data needed particularly the Arithmetic and Logic Unit. I. Hard drive
    _____10. Tec hnology that doubles the maximum bandwidth of SDRAM. J. Memory module

    D. Direction: Is ICT an integral part of our lives? Explain your answer (10 points)

    You might also like