0% found this document useful (0 votes)
18 views2 pages

Machine Design Probs

Uploaded by

generaoysa07
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
18 views2 pages

Machine Design Probs

Uploaded by

generaoysa07
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

1. A marine propeller shaft is to transmit 3.

7 speed of 550 rpm, determine the torsional


MW at 126 RPM without exceeding a stress developed on the 50 mm motor
torsional stress of 42 MPA or twisting shaft. ANS: 5.287 MPA
through more than 2 degrees in a length 11. Two shafts are connected by a flange
of 20 diameters. Determine the shaft coupling and is secured by 6 bolts, 20 mm
diameter. ANS:324 mm in diameter on a pitch circle diameter of
2. Steel railroads rails 10 meter long are laid 150 mm. If a torque of 120 N-m is applied,
with clearance of 3mm at a temperature determine the shear stress in the bolts.
of 15 degrees C, at what temperature will ANS: 0.849 MPa
the rails just touch? In addition to this, at 12. A shaft that transmits 130 kw at 1250 rpm
what temperature will the rails develop an had a rectangular key used in its pulley
axial stress of 150 KSI? ANS: 40.64 C, 468 connection. Considering that the shearing
C stress of the shaft is to be 47 MPA and the
3. A hollow column with di=1/4 do is to key to be 206 MPa, determine the width of
support a dead load of 35 tons, the the rectangular key. ANS: 11.891 mm,
material is steel at 1500 C, determine the 17.047 mm
outside and inside diameters using a yield 13. A flange coupling is to be designed using
strength of 125 KSI and a design factor of 25 mm diameter bolts at a distance of 152
5. ANS: 1.375 in, 0.344 in mm from the center of the shaft, allowable
4. A steel railway track 11 km in length is stress on the coupling is 103 MPA. If the
laid at a temperature of 15 degrees C, if flange is 28 mm thick and the shaft is to
the track is to slide forward, how far apart be transmit 5800 HP at a speed of 1200
will the ends of the track be in ft when the RPM. How many bolts are needed in the
temperature is increased to 69 C. ANS: connection? ANS: 4
36,113.80 ft 14. A solid steel machine shaft with a safe
5. A solid circular shaft is used to transmit shearing stress of 7300 psi and transmits
200 HP at 1000 RPM. If a hollow shaft is a torque of 12,500 lb-in. A square key is
used having an inside diameter equal to used whose length is equal to 1 ½ times
the diameter of this shaft, if the angular the shaft diameter. Find the key
trust of the hollow and solid shafts is to be dimensions. ANS: 0.515 in, 3.087 in
equal? The allowable maximum shearing 15. A flange bolt coupling of 8 ¾ in diameter
stress is 20,000 PSI, determine the inside bolts spaced evenly around a bolt circle of
and outside diameters of the hollow shaft. 1 ft diameter. Determine the shaft
ANS: 1.475 in, 1.8 in diameter if the allowable shearing stress
6. Wires with 7mm diameters and 9.5 m in in the bolts is 5300 psi and in the shaft is
length are used to suspend two masses of 7000 psi. ANS: 4.340 in
170 kg, one of the wires is steel and the 16. A flange bolt coupling has ten steels 1 in
other is aluminum. How much lower will bolts evenly tightened around a 415 mm
the mass held by the aluminum wire be? bolt circle. Determine the power that the
ANS: 3.98 mm connection can transmit at 650 rpm if the
7. A round steel shaft rotates at 200 RPM and allowable shearing stress in the bolts is 50
is subjected to a torque of 226 N-m. The MPA. ANS: 3578.50 KW
allowable shearing stress is 41.4 MPA. It is 17. A flange coupling connects two 50 mm
also subjected to a bending moment of shafts, the coupling has an outside
339 N-m. Find the diameter of the shaft if diameter of 200 mm. there are eight 16
it has an allowable tensile stress of 55 mm bolts on a 140 mm bolt circle.
MPA. ANS:41.039 mm Determine the shear stress in the bolts if
8. A round steel shaft transmits 50 KW and the flange thickness is 30 mm and if the
rotates at 150 rad/s. Find the angle of torsional stress in the shaft is designed to
twist for a 3 m long shaft if the allowable not exceed 27 MPA. ANS: 5.886 MPA
shearing stress is 40 MPA. ANS: 4.75 18. Two short shafts having identical
degrees diameters of 40 mm and rotating at 550
9. A hollow shaft with outside diameter of 14 rpm and connected to a flange coupling
cm and wall thickness of 0.8 cm transmits having four bolts within a 5 in bolt circle.
200 kw at 400 rpm, what must be the The design shearing stress of the bolts is
angular deflection of the shaft if the length 1.7 kips/in^2 and the design compressor
is 5 m. ANS: 1.136 degrees stress of the flange is 2.2 kips/in^2. How
10. A pump is connected to a motor by means thick should the flange be in mm? ANS:
of a coupling. The pump capacity is 4 cum 10.77 mm
per minute of water against a head of 5 in.
If the efficiency of the pump is 70% at a
19. Kindly solve for the power of a line shaft,
which has a diameter of 1.5 in rotating at
200 rad/s. ANS: 120.482 HP

You might also like