Job Data Processing

Module 1: Introduction to JobMaster

Module 2: JobMaster Setup

Confidential. Not to be copied, distributed, or reproduced without prior approval. © 2017 Baker Hughes, a GE company, LLC - All rights reserved.

© 2010 Baker Hughes

Course Objectives
• After finishing this Job Data Processing training
course, students should be able to:
• Identify and apply the process to capture and use
data in the field.
• Navigate through Job Master to produce post job
reports.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Module 1: Introduction to
JobMaster
• Introduction to Monitoring
• Lesson1

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Module 1 Objectives
• Recall different types of jobs and data, identify the
correct template used to capture and process them.
• Recall and identify different types and features of
monitoring devices, software (JobMaster 4.10) and
sensors.
• Recall and introduce the feature and general process of
JobMaster used to capture data.
• Recall the knowledge of basic electronics related to
monitoring devices and process.
• Distinguish the data transmitting process of different
types of sensor.
• Set JobMaster to receive the data properly.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Monitoring of Job Parameters
• Real time information about what is occurring
• Instantaneous values
• Trend analysis

• Post job information

• Well file
• Job evaluations

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Types of Jobs and Data

• Cement job • Gravel pack

• Rate • Rate
• Pressure • Pressure
• Density • Gravel concentration
• Fluid and Proppant volumes
• Acid treatment
• Rate
• Pressure
• Product Volumes
• Skin Factor

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Types of Jobs and Data (cont.)
• Frac Treatments
• Rate
• Pressure
• Sand Concentration
• Liquid Additive Concentrations
• X-linkers, buffers, surfactants, breakers
• Dry additive concentrations
• Breakers, fluid loss additives
• Fluid properties
• Viscosity, pH, temperature

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Types of Jobs and Data (cont)
• Coil Tubing Treatments
• Tubing weight
• Well head pressure
• Treating pressure
• Fluid rate
• Nitrogen rate
• Running Rate
• Depth

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Different Types of Monitoring
Devices • 3305 Mini Monitor
• Data Map
• Isoplex
• VisiPlex
• MicroPlex
• Isolink Wireless
• Wireless Wellhead Unit
• MCM2000

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Mini Monitor 3305 Features
• Weather Proof
• Shock Resistant
• Dedicated Configuration
Rate 1 +2
Rate 3
Pressure 1
Pressure 2
Nuc density or PSA
Aux density
Strip Chart Recorder
• Data Cassette

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Mini Monitor 3305 Features
• Output to printer or computer
• Output to over pressure shut-down
• English or Metric
• Primarily used for cement and small acid jobs

Confidential. Not to be copied, distributed, or reproduced without prior approval.

DataMap System
• Developed For Coiled Tubing Applications
• Major Components
• Personal Computer With True Multitasking Operating
System, Keyboard And Color Monitor
• Data Acquisition Unit (Remotely Mounted Box With Front
End Signal Conditioning And Acquisition)
• Junction Box For Connection To Sensors
• Peripherals
• Displays
• Printers

Confidential. Not to be copied, distributed, or reproduced without prior approval.

DataMap System

DATA ACQUISITION
UNIT
PRINTER

J-BOX

PERSONAL
COMPUTER

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Isoplex Monitoring System
• Stand Alone DAU In Sealed Enclosure w/o Touch
Screen
• Operator Interface Is PC Running JobMaster Software

• 6 voltage inputs
• 6 current inputs
• 12 frequency inputs
• 2 density
• BHI LAN connection

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Microplex Monitoring System
• Designed to operated with JobMaster System
• Can be operated with or without wireless BHI LAN
Unit
• Data Input/outputs:
4 Analog Inputs 4-20 mA
4 frequency inputs, 12V
1 Density input from TNS
1 Serial BHI LAN
1 Serial Service Port
• Temp -40 to 70 C operating
• Power: 9-32 Vdc @ 0.5 A

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Visiplex
• With Microplex provides monitoring system for
pressure pumping applications
• Data Input/outputs:
1 BHI LAN ( to connect to Microplex)
2 serial Data ( RS 232 )
1 USB Port ( Front Panel )
2 USB Port ( Rear Panel )
• Color LCD Graphic screen
• Temp -20 to 70 C operating

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Isolink Wireless LAN

• Replaces well site LAN Cabling

• Operates in extremely harsh environments

• Can be configured in the field as a RS232 direct

link or as a distributed base/remote LAN

device

• Complatible with: Job Master/ Isoplex36/3600/etc

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Wireless Wellhead Unit

• Provides complete
monitoring capabilities, at
the well head without the
need for cables, running
back to the monitoring
VAN
• Incorporates Microplex
Monitor / Companion
Battery Pack / Isolink
wireless module

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 Application HTV-1400

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2012 Baker Hughes

 Application STV-2600

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2012 Baker Hughes

Overhead Display

Rate BPM Sand Conc Press Psi WH Press Psi

2.5 2.2 2500 150

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Falcon Cement Pump

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Falcon Control Panel MCM-2000

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Offshore Applications

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 Module 1: Introduction to
JobMaster
• Data Monitoring, Storage, & Display Software

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2012 Baker Hughes

Job Master 4.10-General Introduction
• JobMaster™ is a computer application intended for use in
realtime data monitoring and recording of oilfield treatments.
• Functionality
• Communicates with up to eight data devices, including IsoPlex,
MicroPlex, BJ LAN, Modbus.
• Processes raw data into meaningful parameters
• Displays parameters within meters, plots, overhead displays

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Job Master 4.10-General Introduction
• Provides remote monitoring capability using a cable, phone
connection, or the internet.
• Calculates math and trig. functions, totals, surface and
downhole foam qualities, etc.
• May send serial data out to other devices or applications
• Prints plots or data lists real-time or post-job
• Stores data to disk for future reference

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Job Master 4.10-General Introduction
• 32 bit Windows compatible program
• Primary User interface
Isoplex / Pendant
NowDaq RTU
MicroPlex
• Secondary Data storage and display unit
3305
Isoplex 36
VisiPlex

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Isoplex DAU (Primary user interface)

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 Isoplex DAU

• 6 (0-10)volt
• 6 (4-20)ma
• 12 frequency
• 2 density

• BHI LAN

Confidential. Not to be copied, distributed, or reproduced without prior approval.

JobMaster 4.10
• Features
• Universal support for U.S. oilfield, metric, or user-defined units of
measurement
• Templates for quick job setup and standard display format
• Fluid, proppant, tubing and casing databases
• 450 readings or calculations recorded at a variable storage rate
• 8 customizable viewing windows across 1 to 8 monitors

Confidential. Not to be copied, distributed, or reproduced without prior approval.

JobMaster 4.10
• Inventory view compares designed versus actual fluid stages
• Wellbore view tracks fluid stages as they are pumped
downhole
• Alarms notify when parameters are out of range
• Plots may be zoomed, annotated, and analyzed using a digital
cursor and slope line.
• Data exportable to DT or CSV (ASCII) file formats for use in
other programs.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

JobMaster 4.10
• Job events are logged automatically, entered manually, selected
from a pre-defined list, or recorded from a compatible device.
• Most tasks within the program may be performed on-the-fly.
• Job data may be played back for purposes of demonstration or
parameter recalculation.
• JobMaster Customer version is available for remote monitoring
purposes.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

JobMaster 4.10

IS JM A PRIMARY OR SECONDARY
USER INTERFACE IN THIS CASE?

3305 JobMaster
Cement Jobs , Acid Jobs, and Small Fracs

34

Confidential. Not to be copied, distributed, or reproduced without prior approval.

JobMaster 4.02

3305 JobMaster 3305

Multiple Truck Cement Jobs

Confidential. Not to be copied, distributed, or reproduced without prior approval.

JobMaster 4.02

Confidential. Not to be copied, distributed, or reproduced without prior approval.

JobMaster 4.02
• Program Title Bar- program version, filename, info.
• Main Menu - File, Edit, Options, etc.
• Status Lights -I/O Devices 1-8

37

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 • Status Lights - I/O Devices 1-8
Receiving Not set up Not sending or
Sending
receiving(error)

38

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

 • Status Panels - ET, Stage, Clips, Alarms, etc.

39

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

Display help for clicked on buttons, menus and
windows

40

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Job Control - Start, Pause, Stop, Stage, Event

41

Confidential. Not to be copied, distributed, or reproduced without prior approval.

• View Windows - F2-F9

• Playback Control - Load, Play, Recalc, Pause, stop,

delay.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

JobMaster 4.10- Features and General
Process

• 450 Parameters
measured
constant
totals
Calculated

• Flexibility
units
alarms
resolution

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 JobMaster 4.02
• Add Alarm Parameters to Definition Box
ning Definition has added
or Alarm Parameters now.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

JobMaster 4.10 –Primary View
• When open always displayed on top.
• Can display up to 32 parameters.
• Flexibility
• Fonts
• Colors

45

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 JobMaster 4.10
• 8 Graphics views (F2 - F9)
• May be labeled now
• 256 indicators per view
• Digital
• Bar meters
• Dial meters
• xy plots

46

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

JobMaster 4.10

• Typical View
• 4 digital
• xy plot
• Wellbore plot

Confidential. Not to be copied, distributed, or reproduced without prior approval.

JobMaster 4.10
• Parameter list view
• 8 possible views
• Max 16 parameters
• Auto font adjustment
• Stage change totals

Confidential. Not to be copied, distributed, or reproduced without prior approval.

JobMaster 4.10

• Events
• Manual entered
• Stage changes
• Alarm limits
• Parameter adjustments
• Zero all totals
• Zero selected totals
• Editable

Confidential. Not to be copied, distributed, or reproduced without prior approval.

JobMaster 4.10

• Data export function

• User selected parameters
• Start time
• End time
• Interval
• ASCII “DT” Format

Confidential. Not to be copied, distributed, or reproduced without prior approval.

JobMaster 4.10

• Graphics Printing
• Real-time
• Post job

Confidential. Not to be copied, distributed, or reproduced without prior approval.

JobMaster 4.02
• XY plots allow for annotation
• Real-time
• Post job

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 JFrac
• JFrac stimulation module
• Calculates downhole parameters
• bhtp
• Foam quality
• Perf friction
• bh Proppant
• Sand in pipe
• 1000 stages
• Up to 100 zones/perfs
JFrac is
run in conjunction with
JobMaster
-Updated fluid and Proppant databases

53

Confidential. Not to be copied, distributed, or reproduced without prior approval.

JFrac
• Data to be shared with JobMaster.
• Zone number and Zone depth may be shared with
JobMaster.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

J Send
• For remote data transmission
• Has option to periodically check connection to
JServe for remote transmissions

Confidential. Not to be copied, distributed, or reproduced without prior approval.

JobMaster 4.10
• JobMaster 4.10 for monitoring, data storage, and
data display.
• JobMaster is the most common monitoring system
used by Baker Hughes Pumping Services…
• JFrac 2.5 for bottom-hole calculations (FracRT
functionality)
• JSend 3.5 for remote data transmissions

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Questions

Confidential. Not to be copied, distributed, or reproduced without prior approval.

JobMaster 4.10 - Basic
Electronics
• Our measuring devices fall into three basic categories:
1) Analog:
• Voltage, Current, (& Resistance)
2) Digital:
• Frequency (pulses)
3) Serial Data:
• RS-232, BHI LAN

• The cable for a nuclear densimeter has a special connector,

but it also has an analog voltage signal.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 Analog: Voltage and Current
• In a fluid system we measure: PRESSURE and FLOW
RATE DISCHARGE TURBINE FLOW METER

SUCTION
PUMP

In an electrical system we measure:

ORIFICE
VOLTAGE and CURRENT.
PRESSURE ~ VOLTAGE

FLOW RATE ~ CURRENT

FRICTION ~ RESISTANCE AMMETER

Voltage is like a pressure forcing

BATTERY
electrons to move and current is the flow
of electrons moving in the wire. RESISTOR

Resistance is like friction restricting flow

in the circuit.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Analog: mA, Volts
• Analog signals may be any number between the
range of the analog device. For a 4-20 mA pressure
transducer, the output signal may be 4.22, 7.67, or
15.0 mA for example.
• Pressure transducers, temperature probes, and load
cells output analog signals (most are 4-20 mA).

Analog
Signal

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Digital: Pulses / Frequency

• Think of digital signals as either being “on or off”, “high or

low.” Analog signals may be any number between 4 to 20
mA for example. But, a digital signal is either a “1” or a “0”
and has no in-between.

• Powered Magnetic Pickups, Shaft Encoders, Quadrature

Encoders, Micromotion flowmeters, and some Barton
Computers output digital pulses.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Digital: Pulses / Frequency

• The pulses are basically a square wave voltage, but we are

interested in the frequency of the pulses (pulses/sec).

• The DAU measures the time between each pulse and also
counts the pulses (for depth applications).

Digital
Signal

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Serial Data: RS-232, BHI LAN

• Serial data is basically a stream of numbers separated by

commas.
• Sending and receiving devices need to agree upon a “protocol”
which includes a Start bit, Parity bit, Number of Bits to carry
data and Stop bits. The protocol is encoded in the program for
each device.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Serial Data: RS-232, BHI LAN
• Parity bits allow error checking - to make sure the information
being received is correct.
• We use serial data transfer:
To satellite data to HQ, to communicate between data van and
MCM’s, to send to the Overhead Display, and to send data to a
laptop running FracPro.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Serial Data

• The Isoplex gathers the signals from each connector, converts

them to digital data, and sends a block of information in the
form of RS-232 data.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Serial Data: Connectors

• Connectors • BHI LAN

DB-9, Pins, Sockets Like RS-232, but customized
BHI Wireless LAN
Replaces the LAN cable with
BHI Wireless Modems

Null Modem crossover

Confidential. Not to be copied, distributed, or reproduced without prior approval.

BHI LAN Communication
• Example 1: 6 packets of
data are being sent
BLD1 BLD1 LAM1 LAM2 GAM1 GAM1
o Discharge Suction Additive Additive Gel Gel o o ...
Rate Rate Rate Rate Temp pH

• Example 2: Only 2 packets of data are being sent

BLD1 BLD1
o Discharge Suction o o o o o o ...
Rate Rate

Confidential. Not to be copied, distributed, or reproduced without prior approval.

BHI LAN Communication

• Step 1: Isoplex queries LAN Nodes

• Step 2: Each LAN Node sends a packet of data.
• Step 3: Isoplex receives the packets

• Step 4: Isoplex relays data to JM and JM warns if any

requested data was not received.

LAM3
???
Additive
Rate ??? BLD1 BLD1 LAM1 LAM2 GAM1 GAM1
Isoplex Discharge Suction Additive Additive Gel Gel
Rate Rate Rate Rate Temp pH

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 Module 1: Introduction to
JobMaster
• Sensors

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2012 Baker Hughes

Typical Sensors
• Pressure Transducers
0-5 Volt and 4-20 milliamp
• Flow Meters
Turbine and Mag pick-up
• N2 Meters
Target flow meters
• Density meters (densimeters)
Nuclear

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Viatran Pressure Transducer Features

• Voltage or Current Output

• Multiple Applications
• RFI Protection
• WECO Union Pressure Fitting
• CENELEC & FM Intrinsically Safe

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Theory Of Operation: Component Level

+
SIGNAL CONDITIONING
RB RStrain Gauge CIRCUIT

EXCITATION
0-5V OR 4-20mA OUT
VOLTAGE IN

mV OUT
RA
- RC

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Theory of Operation Volts Pressure
5 20,000 psi

• Voltage
2.5 10,000 psi
0 PSI = 0 volts
20,000 PSI = 5 volts
Then 2.5 volts = ? PSI
• Note: 0 0 psi
Voltage values must be calibrated into engineering
units. Engineering units would be psi, kPa, mPa,
etc...

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Theory of Operation

• Current
Current Pressure
0 PSI = 4 mA 20 mA 20,000 psi
20,000 PSI = 20 mA
0 ma = ? PSI
12 ma = ? PSI
16 mA Range 12 mA 10,000 psi

4 mA 0 psi

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Speed Sensors- 60 tooth Gear

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Speed Sensors- 60 tooth Gear

60 Tooth Gear

Magnetic Pick Up

Measures pump speed not fluid flow

Confidential. Not to be copied, distributed, or reproduced without prior approval.
60-Tooth Gear Assembly
• 60 tooth gear, one pulse
per tooth = 60 pulses per
revolution.

• 0.12 bbl/rev then 1 pulse =

.0020 bbl or 1 bbl = 500
pulses

• PPU = 500 pulse/per/bbl

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Magnetic Pick Up Operation

Permanent
Magnet

Metal Rod

Sensing
Coil V

Target

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Flow Sensor - Flow Meter

Magnetic
Pick UP

Turbine
/ Target

Calibration Factor : multiply X 42 for BPM

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Turbine Flow Meter

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Density

Weight
Density =  =
Volume

Weight Volume

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Absolute Density

Material Weight Volume Density

Type (Pounds) (Gals) (PPG)

8.34 Pounds 1 Gallon 8.34 PPG

Base Fluid

+
1.00 Pound .045 Gallon 22.1 PPG
Absolute Volume, not BulkAbsolute Density, not Bulk
20/40 Sand
9.34 Pounds
9.34 Pounds 1.045 Gallons
1.045 Gallons
Slurry
Slurry Density = Slurry = 8.93 PPG

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Detector Assembly

Detector
Assembly

0-10VDC

Radiation
Energy

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Process Fluid Pipe
Process
Fluid

Process
Fluid Pipe

0-10VDC

Radiation
Energy

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Theory of Operation
• More radiation at detector = more voltage
• Higher the material density, less radiation

• Therefore, higher the density, lower the voltage.

• 8.34 ppg = 13.1 volts

• 16.34 ppg = 5.0 volts
• Then, 8.5 volts = ? ppg 12.84 ppg

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Sensors
• Quadrature ( End Coder) - used to measure coil
tubing depth. Increase counts going in the hole,
decreases counts coming out of the hole.

• Generally located on the injector to measure tubing

movement in one of two ways

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Sensors

• They generate pulses on two channels, A & B which

are sent to the DAU on separate wires.

• Electronics in the DAU measure the phase shift

between these two pulses in order to determine
which direction the encoder shaft is rotating.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Sensors

• Temperature is usually a current device that uses a

4 to 20 milliamp signal.

• Temperature probes are primarily used to measure:

Nitrogen gas flow
Liquid Add gel temp

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Sensors
Temperature Probe

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 Module 1: Introduction to
JobMaster
• Serial Data Transfer

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2012 Baker Hughes

Typical transfer formats
Baud Rate
• 3305 - 9600, E, 7, 1 Parity

Data Bits
• 3600 - 9600, E, 7, 1
Stop Bit
PROTOCOL
• Isoplex 36 - 9600, E, 7, 1

• Isoplex - 38400, N, 8, 1

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Typical transfer formats
• BHI LAN - 38400, N, 8, 1
• Protocol is made up of the parity, data bits, and stop
bit and each protocol is encoded in the system for
that particular piece of equipment or monitoring
system.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Terminology
• Baud rate
Typically 1200, 2400, 4800, 9600, etc.
Number of bit transfers per second, the higher the #,
the faster the data is transmitted!!
• Data Bits
Measurement of actual data bits per transmission
Typical 5,7, or 8
• Stop Bits
Signals the end of the packet
Typically 1 or 2

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Terminology
• Parity
Simple form of error checking
Even (E), odd (O), marked (M), none (N)
• Handshaking
Not used with BHI equipment
• Data Packet
Start bit, data bits, parity bit, stop bit
Example: N, 8, 1 requires 11 bits
Start bit, 8 data bits, parity bit, 1 stop bit

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Required Speed

• If a serial transmission consisted of 100 parameters

being sent with N,8,1 protocol. How fast would the
baud rate need to be to keep up if data is being sent
1 per second?

• Parameters usually average 6 characters and one

packet is needed for each character.
• 100 * 6 * 11 bits = 6600 bits
• Required baud rate 9600 bits/second

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Order number
• The position of a specific value in the data string.
• Example - 3305
et, press1, press2, flow1&2, flow3 ,aux, nucden (ppg),
nucP(psa), f1+f2 stage, f1+f2 total, f3 stage, f3 total

1.20, 1000, 1235, 6.0, 0, 0, 9.0, 1.50, 10.0, 10.0, 0, 0

2.40, 1010, 1240, 6.1, 0, 0, 9.1, 1.55, 10.1, 10.1, 0, 0
3.60, 1005, 1238, 6.0, 0, 0, 9.1, 1.55, 10.2, 10.2, 0, 0
4.80, 1006, 1237, 6.1, 0, 0, 9.0, 1.50, 10.3, 10.3, 0, 0

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Order Number
• Isoplex
fixed order

1
• A1, 2 A3,
A2, 3 A4, A5, A6, (Volta
6

• I1,
7 I2, 8 I3, I4, I5, I6, (current)
12

• (Frequency)
• F1,
13 F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, D1, 24

• D1,D2,
26 (Density)

• Q1, Q2, Q3, Q4, Q5, Q6, (32Quadrature / End Coder )

• CS1, CS2
34 ( Power Ports)

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Order Number

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 99

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Questions

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 Module 2: JobMaster Setup

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2012 Baker Hughes

Module Objectives
• Choose and set up templates, connect components,
add any functions to parameters for needed data.

• Set general data for job identification.

• Build any graphic views needed for job details.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 Module 2: JobMaster Setup
• Pre-Job Template Setup

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2012 Baker Hughes

JobMaster File Structure
• *.jmd
Contains all setup information including data I/O,
parameters, screen graphics, etc.
• *.eve
Created when the program started; contains all
events
• *.pba
Created when the program started; contains all data
• These 3 files are the basic makeup of a Job file.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

JobMaster File Structure

• When you “save as” you only create a new copy of

the *.jmd file. You do not copy the *.eve or *.pba
files.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

JobMaster File Structure

• C:\Program Files
\BJS
• \JM
\Data
• classdemo.jmd
• 3305_template.jmd
• basic_frac_template.jmd

Confidential. Not to be copied, distributed, or reproduced without prior approval.

JobMaster Templates

• Types of Job • Monitoring System

Cement Isoplex
Frac Isoplex 36
Frac with N2 3600 WTA
Frac with CO2 3305
Binary VisiPlex
Matrix Acid
Acid Frac • PC Equipment
Frac Pack Van w/multiple monitors
Coil Tubing Van w/single screen
Laptop

Confidential. Not to be copied, distributed, or reproduced without prior approval.

JobMaster Templates

• Using template of “old jobs”

Change the information contained in “General Information” section
Only the *.jmd file is copied- no data or events
Very handy with doing series of “standard” jobs for one particular
customer

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Screen Resolution Setting

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 Resolution Setting -Overlap Views

Version 4.0 allows you to go directly to overlap views, but

will give you a message telling you of standard procedure,
then allows you to choose yes to make changes anyway.

110

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

Resolution Setting

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Resolution Setting

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Print Setup

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Check the Print Setup

Graphics print best in landscape

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Print Setup

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Print Preview

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Print Preview

You will want to do a print preview after annotating the chart

before printing to ensure no annotations are stacked on each
other and to make sure none are cut off by the edge of the
plot.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 Portrait

118

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Landscape

119

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 Module 2: JobMaster Setup
• Job Setup: 3305 Template

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2012 Baker Hughes

 Open JobMaster:
Open the “3305 Template”
In the file folder “Student Computer JobMaster Files”

121

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

Setup
Copy the template or old job with “Save Setup File As”

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Setup

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Setup
Now the filename is changed to classdemo.jmd

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Setup

Confidential. Not to be copied, distributed, or reproduced without prior approval.

General Data
• Complete data as much as necessary to identify job.

Put your name in

the field: Service
Company
Representative*

Confidential. Not to be copied, distributed, or reproduced without prior approval.

General Data
• Use menu to go to Job Data or page down.

Use the “PgDn” button

to move to the next
page of “Setup”

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Job Data
• Check job type, data storage interval, and job length.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Input / Output Devices
• Check update interval, device type, and serial port
number.

The Device
description is
used to identify
the source of the
data

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Input / Output Devices
• Additional I/O devices can be added as needed

Unit numbers can be used to

identify the source of the
information

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Check parameter list and data source.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Check units and clip limits; a clip limit tells the
program to ignore the value.

Clip limits filter out

erroneous data

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Set the clip limits well above the expected levels.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Check the output units and the output format. The output
format allows you to show the level of precision desired.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• You can set an alarm value for each parameter. If the value
exceeds the alarm value, a message and an event will be logged.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• When alarms have been set in parameters, the
indicator will show an alarm being turned on.

136

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• To add additional parameters, click on the button
between the Order column and the Definition field.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Click on the Device LOV to designate the device.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Select the parameters and click Add and then OK.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Select Yes (entire parameter) to pre-populate the
Parameter descriptions and source to the page.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• The additions will be made to the Sources tab.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Type in the other unit number in the description
field and paste to the other descriptions.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• On the Units (Input) tab, select the appropriate
Measurement to achieve the desire Input Unit.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Clip Min. and Clip Max default values will be added, but you may
input other values.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• The Output Format allows you to choose the degree
of precision you desire to display.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• On the Display Ranges and Alarms, you may choose
min and max alarm values.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Additional parameter descriptions can added as
required.

Click on the
Measured button to
access additional
parameter options

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Seven additional calculated parameter may be
selected from the tabs.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Click on the Math tab, then double click on the field to access the
list of parameters or input a constant value.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Using the first LOV will allow the user to select various
trigonometric and algebraic functions.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Select the desired parameter by double clicking the Parm or
Const field.

151

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Select the desired math function.

152

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• After selecting all parameter and functions, click OK.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Set the measurement on the Units Input tab using the “LOV”

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Add as many additional parameters as desired.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 156

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 157

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

 158

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

 159

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

Device Parameters
• Check the data out page to ensure “Data Out Enabled” has a
check mark in it.

Add these parameters to the

overhead displays by double clicking
in the space and selecting the
correct parameter

Cannot page down , click OK

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Parameter List View (F9)

Make any changes by double clicking on the view

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 Device Parameters
• To change a displayed item, double click on the display and pick
the new parameter.

162

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

 • Click on LOV button and select the new value.

163

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

  Then click on the “OK” button to effect the
change.

164

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

 • The change is made.

165

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

 • Changes can be made to as many indicators as needed.

• Change F3 stage and F3 total to reflect stage and total for

C879

166

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

JobMaster Job Setup

• Save file to save any changes.(Save Setup File)

• You are now ready to start monitoring.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Questions

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Exercise 1-3305 Template

• Now do the “3305 Template Exercise.”

• See Student Handout

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 Module 2: JobMaster Setup
• Job Setup-Frac Template
• Real Time Data Acquisition

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2012 Baker Hughes

 Job Setup: Frac Template
• More complex frac template

171

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

Device Parameters
• Check calibration numbers, especially flowmeters.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Mouse click on definition to bring up calibration menu.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Enter the proper PPU number of the size flowmeter.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Densimeter calibration for Proppant

The “Auto Reference” button should only

be used to obtain the “Reference ASG”
when the densimeter is full of fluid which
has no Proppant in it.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Check LAN id’s to make sure they are correct and match the
equipment used.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Click on the button between the Order and Definition columns to
change device parameter settings.

Change Xlinker
from LAM 1 to
LAM3

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Click on the Node LOV button to select proper Liquid
Additive Module number for the additive.

Change Xlinker
from LAM 1 to
LAM3

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Multi-select the desired parameters and click OK.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Select Yes (source only) to save your own
Description for the additive on the Parameter setup page.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• The change will be made for that LAN id.
Selecting Source only changes the definition field and not the
description

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 Select Overhead Display : Check the “Data Out Enabled” box.

182

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

To change slurry rate to discharge rate, double click on the Slurry
Rate meter, and select the LOV to change to discharge rate.

183

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 184

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

Device Parameters
• To change scale on the XY plot, just double click on the plot.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Change the appropriate value, click on OK.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• The change is made.

From 60 to 100

From 10,000 to 8,000

From 240 to 120

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Device Parameters
• Save file to save any changes.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

JobMaster Job Setup

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Questions

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Exercise 2- Frac Basic
Template
• Now Do the Frac Basic Template Exercise.
• See Student Handout

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Questions

Close the set up file

Confidential. Not to be copied, distributed, or reproduced without prior approval.

15 minute break

193

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Quiz

194

Confidential. Not to be copied, distributed, or reproduced without prior approval.

FS: Job Data Processing
• Day 2 Presentation

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes Incorporated. All Rights Reserved.
Day 2 Overview

• Module 2: JobMaster Setup (Lesson 4)

• Module 3: JobMaster Operation

• Module 4: JTrax

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Building Graphic Views
• Open “Matrix Acid Job 1.jmd”

Confidential. Not to be copied, distributed, or reproduced without prior approval.

• Click on “View” and open F3

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Building Graphic Views
• Double click on the view , highlight Arc Meter, then click on
Parms->

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Building Graphic Views
• Select the desired parameters to create Arc Meters, click OK.

200

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Building Graphic Views
• Select the Bar Meter and click on Parms->

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Building Graphic Views
• Select the desired parameters to create Bar Meters, click OK.

202

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Building Graphic Views
• Select XY Plot – Notice Parms-> is not available.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Building Graphic Views
• Three Arc Meters at the top of the view
• Two Bar Meters below the Arc Meters
• The XY Plot below the Bar Meters

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 Building Graphic Views
• Note the small numbers in the upper right corner of each
indicator. These numbers tell you the view is unlocked. When
you lock the view the numbers disappear.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Building Graphic Views
• Setting up the XY Plot; double click on plot.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Building Graphic Views
• Select Variables and Ranges

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Building Graphic Views

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 • To build or add events into the Event Database, click on
“Databases” on the Menu bar and select “Event.”

209

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

Building Graphic Views
• You can add as many events as you need, and they will remain
in the database from job to job, unless they are deleted by
someone.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Module 3:JobMaster
Operation
• Monitoring

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Module Objectives
• Module 3: JobMaster Operation

• Verify settings and calibrations of software in templates.

• Start monitoring and recording required data for job.
• Set events and stages to reflect accurate details of the job.
• Export data, set up, and print JobMaster files.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Start Monitoring
• Check to make sure everything is connected:
Serial cable, printer, overheads, etc.
• Turn on the computer.
• Double click on the JM Icon.
• Open the desired template.
• “Save Setup File As” new file name.
• Make any required changes.
• Save changes.
• Now your ready.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 Monitoring
• To start, click on the signal light or use the run menu.

Start Monitoring

214

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

Monitoring

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Deleting Old Data
• An error message stating recorded data exists
indicates the file has been started before, and to use
the file, you must delete the old data.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Deleting Old Data
• Under the file menu, one option is to delete recorded data.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 • You will get a confirmation that the data is deleted.

218

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

Click on the signal light to start monitoring.
• Checking Connections

Confidential. Not to be copied, distributed, or reproduced without prior approval.

• The program goes into a pause mode, this allows you to check
connections and calibrations before recording data.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 • Note the red indicator on device 1, this means no data
is being read from that port.

After trying 100 times to receive data,

the program
gives a warning of I/O problem.

221

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

Checking Connection
• The user can choose to ignore the problem and
continue or to pause the I/O device.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Checking Connection
• After checking, a cable was found loose, please note the
device 1 indicator is now green.

4330

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Checking Connection
• A view of the I/O screen shows data being received.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 • In this example, after you start the job, you cannot un-pause
the program.

225

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

Checking Connection
• This is because the program is expecting to receive
Elapsed Time from another device.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 • Once the device starts to send elapsed time, the program
starts recording and displaying the information.

227

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

Module 3: JobMaster
Operation
• Job Operation
• Real Time Data Acquisition

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 Rescale XY Plot
• To rescale the XY plot, double click on the plot.

229

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

XY Plot
• Change the max and min to the desired values.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

XY Plot
• Max pressure to 5000 and max rate to 10 and the
max density to 20.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 • Click on OK and the graph is rescaled.

232

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

 • To change
Change stage, just
Stage andincrement the stage from the stage icon
Add Event
or event menu.

Confidential. Not to be copied, distributed, or reproduced without prior approval. 233

© 2010 Baker Hughes

 • To change stage, just increment the stage from the stage icon
or event menu.
Stg2
Stg 1

234

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

 Change Stage and Add Event
• You can add an event from the event menu or event icon

235

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

Change Stage and Add Event
• You can add an event from the event menu or event icon

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Change Stage and Add Event
• Events can be manually entered or selected from a list of
user defined events.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Change Stage and Add Event
• Add as many events as necessary to describe the job.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Change Stage and Add Event
• To check or change calibration of a parameter, place the
cursor on the indicator and right click, and select define.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 • This will bring up the calibration screen; make the necessary
changes.

240

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

Check Calibration and Flow Signals
• Here the max density was corrected from 22ppg to 20ppg

Do NOT make this change now!!

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Check Calibration and Flow Signals
• Flow (frequency) signals

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Check Calibration and Flow Signals
• Allows you to correct the PPU number or do a reverse
calibration.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Parameter List View
• Parameter list view allows for values to be reviewed during
the job and sent to a printer.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Parameter List View
• Turn on the Automatic Print select the interval to print.
• Show CT as TOD = clock time as time of day

Confidential. Not to be copied, distributed, or reproduced without prior approval.

XY Plot Setting
• The XY plot can be a trend plot or a moving window like a strip
chart; double click on the plot area.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

XY Plot Setting
• Set the range for the time desired.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

XY Plot Setting
• Now the plot covers 10 minutes, when the data gets to
the end of the time window, the plot rescales automatically.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

XY Plot Setting
• When in trend mode, the program allows a zoom function
to look more closely at the data.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

XY Plot Setting
• Place the cursor in the area of interest, hold down the Left
mouse button, and draw a box around the area.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

XY Plot Setting
• The area outlined will now fill the entire plot area, you can zoom
in as far as necessary to get the detail desired.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

XY Plot Setting
• To clear the zoom, double click on the plot.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

XY Plot Setting

And, the plot returns to normal.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Stop the Job
• To stop the job, click on the red signal light or use the run
menu.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Stop the Job
• Using “Run” to stop the job

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Stop the Job
• The program will request a verification.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

XY Plot Setting
• If you need to continue, you cannot restart without
deleting all the job data.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Resume the Job
• However, you can resume the job which continues to add
data to the existing data file.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Resume the Job
• The only data lost is the data during the time the program was
stopped.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Alarms
• In this set up we have a high alarm set at 4,000 psi on
Pressure 1

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Alarms
• When we exceed the value for the alarm we get a text box
pop up message and the indicator value also changes colors
to match the high alarm

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Clip Limits
• Clip limits for flow 1+2 is set for 500 bpm.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Clips
• A stay noise signal sets off the clip warning, but does
not show up as data.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

• Zero all totals, stage totals, or selected totals being calculated
by JobMaster. All totals being read from outside are not
affected.

264

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Totals
• Modify parameters allows you to continue monitoring even
when a signal is lost or to correct an erroneous value.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Questions

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Break time

267

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Exercise 3 – RT Demo
Exercise
• Do RT Demo Exercise to step number 9 and stop to await
further explanation . After stopping for explanation, save your
changes.
• Pump Procedure is in handout material.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Exercise 3 – RT Demo Exercise

When doing the densimeter correction, wait

until the density of the slurry levels off as in
the example, before making the correction.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Exercise 3 – RT Demo Exercise

After the Lead Slurry starts down hole:

Build three ARC meters on View F3
Flow 1 & 2 , Pressure 1, & Nuc Density

Confidential. Not to be copied, distributed, or reproduced without prior approval.

 Send the Data

271

Confidential. Not to be copied, distributed, or reproduced without prior approval.

© 2010 Baker Hughes

Module 3: JobMaster
Operation
• Post Job Setup
• Real Time Data Acquisition

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Add Annotation
• To stop the job, click on the red signal light or use
the run menu.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Add Annotation
• The program will request a verification.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Add Annotation
• To add annotations double click on the chart

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Add Annotation
• Turn on the annotate option, and change the max Elapsed
Time to fit the length of the job and click on OK.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Add Annotation
• Position the cursor on the target of the text and type in
text being sure to click on the proper Y-Axis indicator

277

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Add Annotation
• Add as many comments as necessary.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Add Annotation
• To change or correct annotations, double click on
the chart, choose the annotations tab.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Add Annotation
• You select the annotation and make changes,
remove, or remove all.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Add Annotation
• Here we changed “Pressure test lines” to “test lines
to 5000psi.”

Confidential. Not to be copied, distributed, or reproduced without prior approval.

And the change is reflected on the chart.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Printing Charts
• Now let’s click on Print Setup…

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Printing Charts
• Change the orientation from “Portrait” to “Landscape,” and
click on “OK.”

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Printing Charts
• When your ready to print, select Print Preview from
the File Menu.

285

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Printing Charts
• Select the printing option desired.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Printing Charts
• Preview the XY plot to ensure that all annotations are as you
wanted them.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Printing Charts
• If the XY plot is ok then click the “Print…” button to print.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Printing Charts
• Windows will verify the print information, click OK, and the
printing will start.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Printing Charts
• If you did not print the Parameter list view during the job, you
can do it now.

Double click on the view

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Printing Charts
• Double click on the view, review the parameters you are going
to print, turn on the automatic print, and set the print interval.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Printing Charts
• Click the green arrow to playback the job or use Run,
Playback Recorded Data, Start (Recalc Off).

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Printing Charts
• The program will inform you that printing will occur
is it OK to proceed? Click on OK.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Printing Charts
• The program will replay the job, display the data,
and print the data after each page is filled.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Printing Charts
• After the job, edit the events to add, remove, or clarify any
events entered during the job.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Edit Event
• To add an event, click on the add button.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Edit Event
• Enter the clock time, and click OK

Confidential. Not to be copied, distributed, or reproduced without prior approval.

• Enter the new event from the user events or manually enter,
then click OK

298

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Edit Event
• The new event is entered, to remove an event

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Edit Event
• Highlight the desired event, then click on remove.
• The program offers to remove all events with the same code.
Use this function with care.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Edit Event

After you have completed the edit process, you can print a copy of the event
file.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Export Data
You might be required to export data from JobMaster. You would do this to
give a customer a copy of the data.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Edit Event

The exported data will be saved as a “*.DT” file. You can keep the same
file name or change it.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Export Data

You can export all the data, or only selected parameters. You can also control
the start and stop time, plus the data interval.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Export Data
You can also export the Historic views in a .rtf file type.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Export Data

Choose the desired place to export.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Export Data

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Closing the Set up File

You might need to close JobMaster to work with another program or

another data file.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Reloading the Data
When you reopen the file…

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Reloading the Data

No data will be available.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Reload Data

To recover the data, click on the playback arrows or go to the run

menu and load the recorded data.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Reload Data

All the data will be reloaded into the program. You can now change plots,
change parameters, or export data.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Reload Data

An additional option is to “Playback recorded data” with “Recalculation

on” This is useful to correct data.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Reload the Data

Depending on the specific computer, playback can occur very rapidly.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Reload Data

If the operator is trying to correct data, it may occur too fast. The delay,
will slow down the job playback speed.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Reload Data

The new data will be stored in a *.PBB file. The original data is intact and
never changed.

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Reload Data

PBA file original data, PBB is the corrected data

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Archiving of Data

• Depends on the policy of the District as of this time.

BY :
Month
Customer
Field Receipt Number

Confidential. Not to be copied, distributed, or reproduced without prior approval.

Questions

Confidential. Not to be copied, distributed, or reproduced without prior approval.