Data Sheet

LED NEON FLEX

Outdoor Flex LED
(FN9/R65/220-FN9/Y65/22-
FN9/6565/220-FN9/2765/220
FN9/B65/220-FN9/G65/220)

Version.2 1
www.ilker.com.tr www.iled.com + 90 212 245 45 00 [email protected]
General Informations:

Features:

 AC 220V
 High brightness low power consumption
 LED type: 2835 SMD LED
 LED quantity: 120 Led /m
 Power：12.6 W
 Size：8.5*16*9 mm
 Packing：50m/roll 16kg/ctn
 1m/cut
 Max link 50meters with one power cord

Application ：

 Business premises lighting

 Exhibition lighting
 Home Lighting
 Office lighting
 Courtyard lamp, Landscape lamp, Decoration lamp for
outdoor lighting

Version.2 2
www.ilker.com.tr www.iled.com + 90 212 245 45 00 [email protected]
Product Features:
1.Milky ,Crystal and Colored PVC jacket design as customer
ordered.
2.Dome,continous and uniform illumination,no LED dot or
dark spot
3.Extremly flexible
4.100% waterproof,100% breakage free,Durability,Impact
Resistance ,Weather Resistance
5.Low voltage or line voltage options
6.Minimal heat output(safe to the touch)
7.Longer Life
8.Easy to install (cuttable n location),Extermly low
maintenance costs
9.70% less energy consumption of glass neon.
10.Available in 7 fixed colors,RGB and digital RGB colors

Version.2 3
www.ilker.com.tr www.iled.com + 90 212 245 45 00 [email protected]
Electrical and Flux Characteristics

Table 1: Flux Characteristics

Number of
Code Case Color Wavelenght Flux Power
LEDs (M)
SMD 621,8 89,84
FN9/R65/220 120 Red 9,8W
2835 nm lm/m
SMD 220,71
FN9/Y65/220 120 Yellow 589,6 nm 10,4W
2835 lm/m
SMD 45,71
FN9/B65/220 120 Blue 462,6 nm 9,9W
2835 lm/m
SMD 147,91
FN9/G65/220 120 Green 519,1 nm 10,2W
2835 lm/m
SMD 244,5
FN9/6565/220 120 Cold White 6045 K 10,6 W
2835 lm/m
SMD Warm 242,2
FN9/2765/220 120 2828 K 10,4W
2835 White lm/m

Version.2 4
www.ilker.com.tr www.iled.com + 90 212 245 45 00 [email protected]
Lamp Structurer

Wiring Diagram
a. high voltage of 110V/220V

(*Suggest 50meter in one line as max in real project)

b. low voltage of 12V/24V

(*As considering Voltage drop,suugest 5meter in one line

for DC12V,10meters should give current from two
size;10meter in one line for DC24V,20meters should give
current from two size).

Version.2 5
www.ilker.com.tr www.iled.com + 90 212 245 45 00 [email protected]
 Cutting & Installation
A simple assembly process applied to all of LED Neon
Flex.These instructions work for both interior and exterior
applications.All you will need are a few basic tools and the
LED Neon Flex of your choice
1:Basic Tools
Having a few basic tools readily available will enable you to
quickly and easily assemble Flex Neon.We suggest using a set
of anvil or pruning shears to ensure a straight clean cut,a pair
of blunt or flat jaw pliers,and a heat gun to shrink wrap the
ends and connectors

Pruning shear Heat gun

Screw Driver
Tape Measure

Silicone sealant glue Cutter

Plier Pick/awl tool

Version.2 6
www.ilker.com.tr www.iled.com + 90 212 245 45 00 [email protected]
2.Making the cut and installing the power cord

1.Following the cutting mark showed in picture

2.Cut at cutting mark using heavy scissors(Recommended

using garden pruning shears,hose cutters or box cutter).Be
sure to cut the line square and not on an angle

3.Trim loose wires.Don’t forget to trim any loose wires

hanging out,flush to the PVC with sharpe side cutters or
scissors.

Version.2 7
www.ilker.com.tr www.iled.com + 90 212 245 45 00 [email protected]
4.Using a pliers hold connecting pin and insertthe pointed end
of the electrical pin into the endof neon flex.The pin must be
installed on the right side or it will not line up with the end cap
on the power cord.

5.Using silicone sealant glue,seal the power cord cap

6. Aligning the pins with the receptacle holes in the power

cord cap,gently push the power cord into place

Version.2 8
www.ilker.com.tr www.iled.com + 90 212 245 45 00 [email protected]
7.Locate the heat shrink tube

8..Using the heat gun,gently warm the heat shrink tube until
it shrinks into its final resting place,after completed,seal
around both ends of the shrink tube with silicone sealant
glue.

Version.2 9
www.ilker.com.tr www.iled.com + 90 212 245 45 00 [email protected]
 3.Installing the end cap

1.Using silicone sealant glue,seal the 2.Gently push the end cap onto the
end cap end of LED neon flex.Slide the end
cap all the way into position where
the LED neon flex touches the back
portion of the end cap.

3.Locate the heat shrink tube and slide 4.Usng the heat gun,gently heat the heat
shrink tube until it is sealed into
it onto the LED neon flex.Allow the
place.Seal both ends of the heat shrink
heat shrink tube to extend past the free tube with silicone sealant glue.This will
ensure that the end cap is securely
end of the end cap approximately 1/4
attached and the connection is
to 3/8 inch impermeable to moisture.

Version.2 10
www.ilker.com.tr www.iled.com + 90 212 245 45 00 [email protected]
4.Installing the splice

1.Using the pick/awl tool,gently spread both

wires in the exposed end of the LED neon

flex.This will allow for ease of inserting the

connecting pin and ensures good contact

between the pin and the wire,making for a

solid electrical connection 2.Position the connecting pin so as to insert

into one selection of LED neon flex with

pick/awl tool.Gently push the pin into the

wires

3. Using silicone sealant glue,seal the both 4. Gently push the straight connector onto
the end of one selection of LED neon
ends of straight connector flex.Slide the straight connector all the
way into position where the LED neon
flex touches the back portion of the
straight connector.

Version.2 11
www.ilker.com.tr www.iled.com + 90 212 245 45 00 [email protected]
5.Same handling of connecting pin and 6.Illustration for completed connection
straight connector for the other selection
of LED neon flex of two selections of LED neon flex

7.Location the heat shrink tube to the joint, 8. Usng the heat gun,gently heat the heat shrink
tube until it is sealed into place.Seal both ends
Allow the heat shrink tube to extend past
of the heat shrink tube with silicone sealant
the free two ends of the straight connector glue.This will ensure that the end cap is securely
approximately 1/4 to 3/8 inch attached and the connection is impermeable to
moisture.

Note: Allow time for silicone sealant glue to cure.It should be ready to handle after 30

minutes,and will cure completely within 24 hours depending upon the manufacturer

Version.2 12
www.ilker.com.tr www.iled.com + 90 212 245 45 00 [email protected]
Safety Precautions
1. Do not over extend the min. & max. bend radius.See illustrations for bending
2. Although LED Neon Flex does not generate a great amount of heat,it is
recommended that you do not cover or conceal it.

3. Do not puncture,cut,shorten or splice LED Neon Flex outside of the designated cutting
marks.
4. Do not route LED Neon Flex through walls,doors,windows,or building structures.
5. Do not roll out LED Neon Flex on rough surfaces and over sharp corners.This will
scratch the PVC optic

6. Do not use LED Neon Flex if outer PVC jacket is damaged,loose connections,or if the

wire is visible without insulation

7. Do not secure LED Neon Flex with staples,nails,or like means that might damage

the insulation or PVC material

8. Do not install LED Neon Flex on/in places where it is subject to continuous flexing
9. Do not operate/run LED Neon Flex in temperatures exceeding 45℃ or 115F

10. Do not operate LED Neon Flex over the specified voltage or LED life degradation
will be greatly increased

11. Do not leave any part of LED Neon Flex unsecured.Movement over time from
weather can cause damage from continuous movement

12. All LED Neon Flex IP68 Rated connectors must be assembled properly to obtain rating
13. Do not reverse polarity when connecting from both ends.This will damage the
internal PCB board.Always test connections with your multi-meter.

14. Do not energize LED Neon Flex in the reel package

15. LED Neon Flex can be cut only where marked.Look for “Indent marking” or
“Dotted line” or “Scissor mark”.Cutting outside of the specified mark will

damage the light

16. Do not cut while fixture is energized

Version.2 13
www.ilker.com.tr www.iled.com + 90 212 245 45 00 [email protected]