Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,

INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 1 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Permanent Facility

1 ELECTRO- AC Current 50 Hz 100 m A to 10 A 0.6% to 0.7% Using 6 ½ DMM Fluke

TECHNICAL- 8846A by Direct
ALTERNATING measure
CURRENT (< 1 GHZ)
(Measure)

2 ELECTRO- AC Current 50 Hz 100 m A to 10 A 0.6% to 0.7% Using 6 ½ DMM Fluke

TECHNICAL- 8846A by Direct
ALTERNATING measure
CURRENT (< 1 GHZ)
(Measure)

3 ELECTRO- AC Current 50 Hz 100 micro A to 100 mA 2.0% to 0.6% Using 6 ½ DMM Fluke
TECHNICAL- 8846A by Direct
ALTERNATING measure
CURRENT (< 1 GHZ)
(Measure)

4 ELECTRO- AC Current 50 Hz 100 micro A to 100 mA 2.0% to 0.6% Using 6 ½ DMM Fluke
TECHNICAL- 8846A by Direct
ALTERNATING measure
CURRENT (< 1 GHZ)
(Measure)

5 ELECTRO- AC Voltage50 Hz 1 V to 1000 V 0.5% to 0.11% Using 6 ½ DMM Fluke

TECHNICAL- 8846A by Direct
ALTERNATING measure
CURRENT (< 1 GHZ)
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 2 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
6 ELECTRO- AC Voltage50 Hz 10 mV to 100 mV 1.5% to 0.5% Using 6 ½ DMM Fluke
TECHNICAL- 8846A by Direct
ALTERNATING measure
CURRENT (< 1 GHZ)
(Measure)

7 ELECTRO- High Voltage 50Hz 1 kV to 5 kV 4.0% Using Motwane HV

TECHNICAL- Probe with DMM
ALTERNATING motwane by Direct
CURRENT (< 1 GHZ) measure
(Measure)

8 ELECTRO- AC Current 50Hz to 1 A to 10 A 0.16% to 0.15% Using Multifunction

TECHNICAL- 1kHz calibrator 5500A Fluke
ALTERNATING by Direct Method
CURRENT (< 1 GHZ)
(Source)

9 ELECTRO- AC Current 50Hz to 100 micro A to 1 A 0.45% to 0.16% Using Multifunction

TECHNICAL- 1kHz calibrator 5500A Fluke
ALTERNATING by Direct Method
CURRENT (< 1 GHZ)
(Source)

10 ELECTRO- AC Current 50Hz to 100 micro A to 1 A 0.45% to 0.16% Using Multifunction

TECHNICAL- 1kHz calibrator 5500A Fluke
ALTERNATING by Direct Method
CURRENT (< 1 GHZ)
(Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 3 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
11 ELECTRO- AC Power @50HzAt 0.5 (1V, 0.5A , UPF to 0.5% to 2.0% Using Multifunction
TECHNICAL- UPF to 0.2 PF 0.2 Lag)@ 50Hz 0.5W calibrator 5500A Fluke
ALTERNATING Watt to 6 ( 600V,10 A, by Direct Method
CURRENT (< 1 GHZ) UPF to 0.2 Lag)@
(Source) 50Hz Watt

12 ELECTRO- AC Power @50HzAt 0.5 (1V, 0.5A , UPF to 0.5% to 2.0% Using Multifunction
TECHNICAL- UPF to 0.2 PF 0.2 Lag)@ 50Hz 0.5W calibrator 5500A Fluke
ALTERNATING Watt to 6 ( 600V,10 A, by Direct Method
CURRENT (< 1 GHZ) UPF to 0.2 Lag)@
(Source) 50Hz Watt

13 ELECTRO- AC Voltage 50Hz to 10 mV to 10 V 0.45% to 0.06% Using multifunction

TECHNICAL- 1kHz calibrator 5500A Fluke
ALTERNATING by Direct Method
CURRENT (< 1 GHZ)
(Source)

14 ELECTRO- AC Voltage 50Hz to 10 V to 1000 V 0.06% to 0.1% Using Multifunction

TECHNICAL- 1kHz calibrator 5500A Fluke
ALTERNATING by Direct Method
CURRENT (< 1 GHZ)
(Source)

15 ELECTRO- Phase Angle 0 ° to 90 ° 0.19° Using multifunction

TECHNICAL- calibrator 5500A Fluke
ALTERNATING by Direct Method
CURRENT (< 1 GHZ)
(Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 4 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
16 ELECTRO- Power Factor 0.2 PF to 1 PF 0.17PF Using Multifunction
TECHNICAL- calibrator 5500A Fluke
ALTERNATING by Direct Method
CURRENT (< 1 GHZ)
(Source)

17 ELECTRO- DC Current 10 micro A to 10 A 0.7% to 0.2% Using 6 1/2 DMM Fluke

TECHNICAL- DIRECT 8846A by Direct
CURRENT (Measure) measure

18 ELECTRO- DC High Voltage 1 kV to 5 kV 2% Using motwane HV

TECHNICAL- DIRECT probe with DMM
CURRENT (Measure) motwane by direct
measure

19 ELECTRO- DC Voltage 1 mV to 100 mV 1.00% to 0.045% Using 6 1/2 DMM Fluke

TECHNICAL- DIRECT 8846A / Direct Measure
CURRENT (Measure)

20 ELECTRO- DC Voltage 100 mV to 1000 V 0.045% to 0.04% Using 6 1/2 DMM Fluke
TECHNICAL- DIRECT 8846A / Direct Measure
CURRENT (Measure)

21 ELECTRO- Low Resistance 1 m ohm to 10 ohm 1.1% Using 6.5 Digit DMM
TECHNICAL- DIRECT and fluke 5500A by V/ I
CURRENT (Measure) method.

22 ELECTRO- Resistance 10 ohm to 100 k ohm 0.7% to 0.2% Using 6 ½ DMM Fluke
TECHNICAL- DIRECT 8846A by Direct
CURRENT (Measure) measure

23 ELECTRO- Resistance 100 k ohm to 100 M 0.2% to 2.4% Using 6 ½ DMM Fluke
TECHNICAL- DIRECT ohm 8846A by Direct
CURRENT (Measure) measure

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 5 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
24 ELECTRO- Resistance 100 M ohm to 1 G ohm 2.9% Using 6 ½ DMM Fluke
TECHNICAL- DIRECT 8846A by Direct
CURRENT (Measure) measure

25 ELECTRO- DC Current 10 micro A to 100 0.6% to 0.07% Using multifunction

TECHNICAL- DIRECT micro A calibrator 5500A Fluke
CURRENT (Source) by Direct sourcing

26 ELECTRO- DC Current 100 mA to 10 A 0.02% to 0.09% Using multifunction

TECHNICAL- DIRECT calibrator 5500A Fluke
CURRENT (Source) by Direct sourcing

27 ELECTRO- DC Current 100 micro A to 100 mA 0.07% to 0.02% Using multifunction

TECHNICAL- DIRECT calibrator 5500A Fluke
CURRENT (Source) by Direct sourcing

28 ELECTRO- DC Voltage 1 mV to 10 mV 1.0% to 0.1% Using Multifunction

TECHNICAL- DIRECT calibrator 5500A Fluke
CURRENT (Source) by Direct sourcing

29 ELECTRO- DC Voltage 1 V to 1000 V 0.015% to 0.01% Using Multifunction

TECHNICAL- DIRECT calibrator 5500A Fluke
CURRENT (Source) by Direct sourcing

30 ELECTRO- DC Voltage 10 mV to 1 V 0.1% to 0.015% Using Multifunction

TECHNICAL- DIRECT calibrator 5500A Fluke
CURRENT (Source) by Direct sourcing

31 ELECTRO- Resistance 1 m ohm to 10 ohm 1.35% to 2.4% Using shunts & Decade
TECHNICAL- DIRECT Box Maxwell, Model
CURRENT (Source) DR 8 Direct sourcing

32 ELECTRO- Resistance 10 M ohm to 100 M 0.08% to 0.6% Using Multifunction

TECHNICAL- DIRECT ohm calibrator 5500 A Fluke
CURRENT (Source) by Direct sourcing

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 6 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
33 ELECTRO- Resistance 10 ohm to 100 k ohm 0.2% to 0.02% Using Multifunction
TECHNICAL- DIRECT calibrator 5500 A Fluke
CURRENT (Source) by Direct sourcing

34 ELECTRO- Resistance 100 k ohm to 10 M ohm 0.02% to 0.08% Using Multifunction

TECHNICAL- DIRECT calibrator 5500 A Fluke
CURRENT (Source) by Direct sourcing

35 ELECTRO- Resistance 100 M ohm to 300 M 0.6% to 1.0% Using Multifunction

TECHNICAL- DIRECT ohm calibrator 5500 A Fluke
CURRENT (Source) by Direct sourcing

36 ELECTRO- Resistance 300 M ohm to 100 G 3.4% Using Mega Ohm Box
TECHNICAL- DIRECT ohm Maxwell, Model DB 231
CURRENT (Source) for calibration of
Meggers upto 5kV by
Direct method

37 ELECTRO- Counter Meter 0 Count to 999999 1.7% to 1% Using Stop Watch and
TECHNICAL- OTHERS Count Fluke Multifunction
(Measure) calibrator 5500A

38 ELECTRO- B type Thermocouples 600 ° C to 1750 ° C 0.75° C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION
(Measure)

39 ELECTRO- E type Thermocouple -200 ° C to 1000 ° C 0.44° C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 7 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
40 ELECTRO- J type Thermocouple -200 °C to 750 °C 0.2°C Using Radix / Fluke
TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION
(Measure)

41 ELECTRO- K type Thermocouple -200 °C to 1350 °C 0.25°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION
(Measure)

42 ELECTRO- N type Thermocouple 50 °C to 1750 °C 0.75°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION
(Measure)

43 ELECTRO- R type Thermocouple 50 °C to 1750 °C 0.41°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION
(Measure)

44 ELECTRO- RTD -200 °C to 800 °C 0.35°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 8 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
45 ELECTRO- S type Thermocouple 50 °C to 1750 °C 0.70°C Using Radix / Fluke
TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION
(Measure)

46 ELECTRO- T type Thermocouple -200 °C to 400 °C 0.27°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION
(Measure)

47 ELECTRO- B type Thermocouple 600 ° C to 1750 ° C 0.75° C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION (Source)

48 ELECTRO- E type Thermocouples -200 ° C to 1000 ° C 0.75° C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION (Source)

49 ELECTRO- J type Thermocouples -200 °C to 750 °C 0.75°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION (Source)

50 ELECTRO- K type Thermocouples -200 °C to 1350 °C 0.75°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION (Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 9 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
51 ELECTRO- N type Thermocouples 50 °C to 1750 °C 0.75°C Using Radix / Fluke
TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION (Source)

52 ELECTRO- R type Thermocouples 50 °C to 1750 °C 0.75°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION (Source)

53 ELECTRO- RTD -200 °C to 800 °C 0.35°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION (Source)

54 ELECTRO- S type Thermocouples 50 °C to 1750 °C 0.75°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION (Source)

55 ELECTRO- T type Thermocouples -200 °C to 400 °C 0.75°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION (Source)

56 ELECTRO- Capacitance 1kHz 1 nF to 100 micro F 3% to 0.7% Using 6 ½ DMM Fluke

TECHNICAL- TIME & 8846A by Direct
FREQUENCY measure
(Measure)

57 ELECTRO- Capacitance 1kHz 100 micro F to 300 0.7% to 1.2% Using 6 ½ DMM Fluke
TECHNICAL- TIME & micro F 8846A by Direct
FREQUENCY measure
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 10 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
58 ELECTRO- Capacitance 1kHz 100 micro F to 300 0.7% to 1.2% Using 6 ½ DMM Fluke
TECHNICAL- TIME & micro F 8846A by Direct
FREQUENCY measure
(Measure)

59 ELECTRO- Digital / Analog Stop 10 sec to 59 min 1.51sec to 2sec Using Digital Time
TECHNICAL- TIME & Watch / Timer interval meter by
FREQUENCY Comparison Method
(Measure)

60 ELECTRO- Frequency 10 Hz to 1 M Hz 0.8%% to 1.40% Using 6 ½ DMM Fluke

TECHNICAL- TIME & 8846A by Direct
FREQUENCY measure
(Measure)

61 ELECTRO- Capacitance 1kHz 0.5 n F to 100 micro F 3% to 0.7% Using Multifunction

TECHNICAL- TIME & calibrator 5500A Fluke
FREQUENCY (Source) by Direct Method

62 ELECTRO- Capacitance 1kHz 100 micro F to 300 0.7% to 1.2% Using Multifunction
TECHNICAL- TIME & micro F calibrator 5500A Fluke
FREQUENCY (Source) by Direct Method

63 ELECTRO- Frequency 10 Hz to 100 k Hz 0.015% to 0.065% Using Multifunction

TECHNICAL- TIME & calibrator 5500A Fluke
FREQUENCY (Source) by Direct Method

64 MECHANICAL- Tachometer / RPM 1000 to 20000 rpm 0.35% Using Non contact
ACCELERATION AND Tachometer &
SPEED Mechanical Tacho-
generator

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 11 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
65 MECHANICAL- Tachometer / RPM up to 1000 rpm 0.38% Using Non contact
ACCELERATION AND Tachometer &
SPEED Mechanical Tacho-
generator

66 MECHANICAL- Sound Level Meter 1 kHz 94dB to 1 kHz 0.85 dB Using Sound level
ACOUSTICS 114dB calibrator

67 MECHANICAL- Hydrometer 0.7 sp.gr. to 1.0 sp.gr. 0.0012 sp. gr. Using Standard
DENSITY AND Hydrometer
VISCOSITY

68 MECHANICAL- Hydrometer 1.0 sp. gr. to 1.8 sp. gr. 0.0016 sp.gr. Using Standard
DENSITY AND Hydrometer
VISCOSITY

69 MECHANICAL- Ball Type Micrometer 0 to 25 mm 2 µm Using Slip Gauge Set

DIMENSION (BASIC L.C. 0.001 mm Grade 0
MEASURING
INSTRUMENT,
GAUGE ETC.)

70 MECHANICAL- Bevel Protractor L.C. 5 0 to 360 deg 1.5 min Using Angle Gauge
DIMENSION (BASIC Min Block & Surface Plate
MEASURING
INSTRUMENT,
GAUGE ETC.)

71 MECHANICAL- Calipers 0 to 1000 mm 18µm Using Caliper Checker

DIMENSION (BASIC (Vernier/Dial/Digital) & Length Bar Set, Slip
MEASURING L.C. 0.01 mm Gauge Set
INSTRUMENT,
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 12 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
72 MECHANICAL- Calipers 0 to 300 mm 13 µm Using Caliper Checker
DIMENSION (BASIC (Vernier/Dial/Digital) & Length Bar Set, Slip
MEASURING L.C. 0.01 mm Gauge Set
INSTRUMENT,
GAUGE ETC.)

73 MECHANICAL- Calipers 0 to 600 mm 13µm Using Caliper Checker

DIMENSION (BASIC (Vernier/Dial/Digital) & Length Bar Set, Slip
MEASURING L.C. 0.01 mm Gauge Set
INSTRUMENT,
GAUGE ETC.)

74 MECHANICAL- Calipers 0 to 2000 mm 25µm Using Caliper Checker

DIMENSION (BASIC (Vernier/Dial/Digital) & Length Bar Set, Slip
MEASURING L.C. 0.02 mm Gauge Set
INSTRUMENT,
GAUGE ETC.)

75 MECHANICAL- Depth Gauge 0 to 300 mm 10.3µm Using Slip Gauge Set ,

DIMENSION (BASIC (Vernier/Dial/Digital) Length Bar Set &
MEASURING L.C. 0.01 mm Surface Plate
INSTRUMENT,
GAUGE ETC.)

76 MECHANICAL- Depth Micrometer L.C. 0 to 300 mm 9µm Using Slip Gauge Set &
DIMENSION (BASIC 0.001 mm Length Bar Set ,
MEASURING Surface Plate
INSTRUMENT,
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 13 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
77 MECHANICAL- Dial Thickness Gauge 0 to 25 mm 2µm Using Slip Gauge Set
DIMENSION (BASIC L.C. 0.001 mm Grade 0
MEASURING
INSTRUMENT,
GAUGE ETC.)

78 MECHANICAL- External Micrometer 0 to 100 mm 4µm Using Slip Gauge Set /

DIMENSION (BASIC L.C. 0.001 mm Length Bar Set
MEASURING
INSTRUMENT,
GAUGE ETC.)

79 MECHANICAL- External Micrometer 100 to 300 mm 7µm Using Slip Gauge Set /
DIMENSION (BASIC L.C. 0.001 mm Length Bar Set
MEASURING
INSTRUMENT,
GAUGE ETC.)

80 MECHANICAL- External Micrometer 500 to 1000 mm 12µm Using Slip Gauge Set /
DIMENSION (BASIC L.C. 0.01 mm Length Bar Set
MEASURING
INSTRUMENT,
GAUGE ETC.)

81 MECHANICAL- External Micrometer 300 to 500 mm 9µm Using Slip Gauge Set /
DIMENSION (BASIC L.C. 0.010 mm Length Bar Set
MEASURING
INSTRUMENT,
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 14 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
82 MECHANICAL- Feeler / Leaf Gauge up to to 2 mm 3µm Using Comparator
DIMENSION (BASIC Stand with Digital Dial
MEASURING
INSTRUMENT,
GAUGE ETC.)

83 MECHANICAL- Height Gauge 0 to 1000 mm 15.1µm Using Caliper Checker

DIMENSION (BASIC (Vernier/Dial/Digital) / Length Bar Set &
MEASURING L.C. 0.01 mm Surface Plate
INSTRUMENT,
GAUGE ETC.)

84 MECHANICAL- Height Gauge 0 to 300 mm 12µm Using Caliper Checker

DIMENSION (BASIC (Vernier/Dial/Digital) / Length Bar Set &
MEASURING L.C. 0.01 mm Surface Plate
INSTRUMENT,
GAUGE ETC.)

85 MECHANICAL- Height Gauge 0 to 600 mm 12µm Using Caliper Checker

DIMENSION (BASIC (Vernier/Dial/Digital) / Length Bar Set &
MEASURING L.C. 0.01 mm Surface Plate
INSTRUMENT,
GAUGE ETC.)

86 MECHANICAL- Internal Micrometer 50 to 100 mm 4µm Using Slip Gauge Set,

DIMENSION (BASIC (Extension Rods) Length Bar &
MEASURING Comparator Stand with
INSTRUMENT, Digital Dial
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 15 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
87 MECHANICAL- Internal Micrometer 5 to 300 mm 7µm Using Slip Gauge Set,
DIMENSION (BASIC L.C. 0.01 mm Length Bar &
MEASURING Comparator Stand with
INSTRUMENT, Digital Dial
GAUGE ETC.)

88 MECHANICAL- Internal Micrometer 50 to 1000 mm 10µm Using Slip Gauge Set,

DIMENSION (BASIC L.C. 0.01 mm Length Bar &
MEASURING Comparator Stand with
INSTRUMENT, Digital Dial
GAUGE ETC.)

89 MECHANICAL- Lever Dial Gauge L.C. upto to 1.6 mm 6µm Using Dial Calibration
DIMENSION (BASIC 0.01 mm Tester
MEASURING
INSTRUMENT,
GAUGE ETC.)

90 MECHANICAL- Lever Dial Gauge upto to 1.0 mm 2µm Using Dial Calibration
DIMENSION (BASIC L.C.0.001 mm Tester
MEASURING
INSTRUMENT,
GAUGE ETC.)

91 MECHANICAL- Measuring Pin 0.1 to 20 mm 1.2µm Using Comparator

DIMENSION (BASIC Stand with Digital Dial
MEASURING
INSTRUMENT,
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 16 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
92 MECHANICAL- Measuring Scale L.C. 1 upto to 1000 mm 117µm Using Steel Scale /
DIMENSION (BASIC mm Tape Calibrator
MEASURING
INSTRUMENT,
GAUGE ETC.)

93 MECHANICAL- Measuring Tape / Pi- 0 to 50 meter 117vL µm L in mtr Using Steel Tape /
DIMENSION (BASIC Tape Tape calibrator L.C. 1
MEASURING mm
INSTRUMENT,
GAUGE ETC.)

94 MECHANICAL- Micrometer Setting > 25 to 100 mm 1.8µm Using Comparator

DIMENSION (BASIC Standard Stand with Digital Dial,
MEASURING Slip Gauges and
INSTRUMENT, Length Bar
GAUGE ETC.)

95 MECHANICAL- Micrometer Setting >100 to 300 mm 4µm Using Comparator

DIMENSION (BASIC Standard Stand with Digital Dial,
MEASURING Slip Gauges and
INSTRUMENT, Length Bar
GAUGE ETC.)

96 MECHANICAL- Micrometer Setting >300 to 500 mm 6µm Using Comparator

DIMENSION (BASIC Standard Stand with Digital Dial,
MEASURING Slip Gauges and
INSTRUMENT, Length Bar
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 17 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
97 MECHANICAL- Micrometer Setting >500 to 975 mm 9µm Using Comparator
DIMENSION (BASIC Standard Stand with Digital Dial,
MEASURING Slip Gauges and
INSTRUMENT, Length Bar
GAUGE ETC.)

98 MECHANICAL- Pin Pointed Micrometer 0 to 25 mm 2µm Using Slip Gauge Set

DIMENSION (BASIC L.C. 0.001 mm Grade 0
MEASURING
INSTRUMENT,
GAUGE ETC.)

99 MECHANICAL- Pistol Caliper L.C. 0.1 upto to 100 mm 75µm Using Slip Gauge Set
DIMENSION (BASIC mm
MEASURING
INSTRUMENT,
GAUGE ETC.)

100 MECHANICAL- Plain Plug Gauge / > 100 to 250 mm 3µm Using Comparator
DIMENSION (BASIC Width Gauge / Height Stand with Digital Dial
MEASURING Setting Block & Slip Gauge Set
INSTRUMENT,
GAUGE ETC.)

101 MECHANICAL- Plain Plug Gauge / 3 to 100 mm 3µm Using Comparator

DIMENSION (BASIC Width Gauge / Height Stand with Digital Dial
MEASURING Setting Block & Slip Gauge Set
INSTRUMENT,
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 18 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
102 MECHANICAL- Plunger Dial Gauge upto to 25 mm 4µm Using Dial Calibration
DIMENSION (BASIC L.C. 0.001 mm Tester, Slip Gauge Set
MEASURING
INSTRUMENT,
GAUGE ETC.)

103 MECHANICAL- Plunger Dial Gauge upto to 50 mm 5.9µm Using Dial Calibration
DIMENSION (BASIC L.C. 0.01 mm Tester, Slip Gauge Set
MEASURING
INSTRUMENT,
GAUGE ETC.)

104 MECHANICAL- Snap Gauge >100 to 250 mm 3µm Using Slip Gauge Set &
DIMENSION (BASIC Feeler Gauge
MEASURING
INSTRUMENT,
GAUGE ETC.)

105 MECHANICAL- Snap Gauge 2 to 100 mm 3µm Using Slip Gauge Set &
DIMENSION (BASIC Feeler Gauge
MEASURING
INSTRUMENT,
GAUGE ETC.)

106 MECHANICAL- Spirit Level Sensitivity ± 1 mm 9 µm/m Using Surface plate &
DIMENSION (BASIC 0.01 mm/m Tilting fixture and
MEASURING Digital Dial Gauge
INSTRUMENT,
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 19 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
107 MECHANICAL- Surface Plate 3000 to 3000 mm 3 µm Using Spirit Level
DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)

108 MECHANICAL- Thickness Foils 0.005 to 2 mm 1.5µm Using Comparator

DIMENSION (BASIC Stand with Digital Dial
MEASURING
INSTRUMENT,
GAUGE ETC.)

109 MECHANICAL- Hydraulic Pressure 0 bar to 30 bar 0.8% of rdg to 0.8% of Using Digital Pressure
PRESSURE Gauge / Digital / rdg Gauge
INDICATING DEVICES Analog Pressure
Gauge / Pressure
Indicator

110 MECHANICAL- Hydraulic Pressure 30 bar to 600 bar 0.8% of rdg to 0.8% of Using digital pressure
PRESSURE Gauge / Digital / rdg gauge
INDICATING DEVICES Analog Pressure
Gauge / Pressure
Indicator

111 MECHANICAL- Vacuum Gauge / (-) 0.9 bar to 0 bar 0.8% of rdg to 0.8% of Using Digital Vacuum
PRESSURE Indicator rdg Gauge by Direct
INDICATING DEVICES Comparison DKD-R-6-
1

112 MECHANICAL- Glasswares - Pipette, 10 ml to 1000 ml 0.05ml Using Standard E1

VOLUME Burette, Measuring Class Weights and
Cylinder, Volumetric Micro Balance, L.C.
Flask, Conical Flask 0.01 mg

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 20 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
113 MECHANICAL- Glasswares - Pipette, 100 microlitre to 10 ml 0.34 microlitre Using Standard E1
VOLUME Burette, Measuring Class Weights with
Cylinder, Volumetric Micro Balance , L.C.
Flask, Conical Flask 0.01 g

114 MECHANICAL- Glasswares - Pipette, 1000 ml to 2000 ml 0.05ml Using Standard F2

VOLUME Burette, Measuring Class Weights above
Cylinder, Volumetric 200 g with Micro
Flask, Conical Flask Balance, L.C. 0.1 mg

115 MECHANICAL- Micro Pipette 10 microlitre to 100 0.25 microlitre Using Standard E1
VOLUME microlitre class Weights with
micro balance, L.C.
0.01 mg

116 MECHANICAL- Micro Pipette 100 microlitre to 1000 0.34 microlitre Using Standard E1
VOLUME µl class Weights with
micro balance, L.C.
0.01 mg

117 MECHANICAL- Electronic Weighing 5g to 80 g 0.03mg Using Standard E1

WEIGHING SCALE Balance Class Weights
AND BALANCE

118 MECHANICAL- Electronic Weighing >300g to 3kg 40mg Using Standard F2

WEIGHING SCALE Balance Class Weights L.C. 0.1
AND BALANCE g

119 MECHANICAL- Electronic Weighing >3kg to 30kg 2g Using F2 Class

WEIGHING SCALE Balance Weights L.C. 1 g
AND BALANCE

120 MECHANICAL- Electronic Weighing 80g to 200 g 0.3mg Using Standard E1

WEIGHING SCALE Balance Class Weights
AND BALANCE

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 21 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
121 MECHANICAL- Electronic Weighing up to 5g 0.03mg Using Standard E1
WEIGHING SCALE Balance Class Weights
AND BALANCE

122 MECHANICAL- Spring Balance 30kg 20g Using F2 class

WEIGHING SCALE Weights, L.C. 1 g
AND BALANCE

123 MECHANICAL- Using weights M1 class 1 mg to 10 mg 0.01 mg Using standard E1

WEIGHTS and coarser class weights with
micro balance

124 MECHANICAL- Weight F1 class and 100 g 0.09mg Using Standard E1

WEIGHTS Coarser Class weights with
micro balance

125 MECHANICAL- Weight M1 class and 500 g 6mg Using Standard F2

WEIGHTS Coarser Class Weights with
micro balance

126 MECHANICAL- weight, M1 Class and 10kg 74mg Using Standard F2

WEIGHTS crosser Class weights with
micro balance

127 MECHANICAL- Weights E2 class and 200 g 0.10mg Using Standard E1

WEIGHTS Coarser Class weights with
micro balance

128 MECHANICAL- Weights E2 class and 50 g 0.03 mg Using Standard E1

WEIGHTS Coarser Class weights with
micro balance

129 MECHANICAL- Weights F1 class and 1g to 20g 0.03mg Using Standard E1

WEIGHTS Coarser Class weights with
micro balance

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 22 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
130 MECHANICAL- Weights F1 class and 20mg to 500mg 0.01mg Using Standard E1
WEIGHTS Coarser Class weights with
micro balance

131 MECHANICAL- Weights M1 class and 1 kg 9 mg Using Standard F2

WEIGHTS Coarser Class Weights with
micro balance

132 MECHANICAL- Weights M1 class and 2 kg 13 mg Using Standard F2

WEIGHTS Coarser Class Weights with
micro balance

133 MECHANICAL- Weights M1 class and 5 kg 68mg Using Standard F2

WEIGHTS Coarser Class Weights with
micro balance

134 THERMAL- SPECIFIC Humidity Meter with in 20% RH to 95% RH @ 1.9 % RH Using digital
HEAT & HUMIDITY Built or external sensor, 25 degree C Hygrometer and
Thermo- Hygrometer Humidity generator with
chamber

135 THERMAL- Liquid in Glass >25 degree C to 80 0.27 degree C Using Fluke RTD (Pt
TEMPERATURE Thermometer, Dial / degree C 100), 6 1/2 DMM &
Digital Thermometer , Fluke Dry Well / Liquid
RTD / Thermocouple Baths
with or without
Temperature Indicator

136 THERMAL- Liquid in Glass >80 degree C to 300 0.27 degree C Using Fluke RTD (Pt
TEMPERATURE Thermometer, Dial / degree C 100), 6 1/2 DMM &
Digital Thermometer , Fluke Dry Well / Liquid
RTD / Thermocouple Baths
with or without
Temperature Indicator

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 23 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
137 THERMAL- Liquid in Glass -30 degree C to 25 0.30 degree C Using Fluke RTD (Pt
TEMPERATURE Thermometer, Dial / degree C 100), 6 1/2 DMM &
Digital Thermometer , Fluke Dry Well / Liquid
RTD / Thermocouple Baths
with or without
Temperature Indicator

138 THERMAL- Thermocouple With or 300 degree C to 1000 1.9 degree C Using S type
TEMPERATURE Without Temperature degree C Thermocouple, 6 1/2
Indicator DMM & Tubular
Furnace

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 24 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

1 ELECTRO- AC Current 50 Hz 100 m A to 10 A 0.6% to 0.7% Using 6 ½ DMM Fluke

TECHNICAL- 8846A by Direct
ALTERNATING measure
CURRENT (< 1 GHZ)
(Measure)

2 ELECTRO- AC Current 50 Hz 100 m A to 10 A 0.6% to 0.7% Using 6 ½ DMM Fluke

TECHNICAL- 8846A by Direct
ALTERNATING measure
CURRENT (< 1 GHZ)
(Measure)

3 ELECTRO- AC Current 50 Hz 100 micro A to 100 mA 2.0% to 0.6% Using 6 ½ DMM Fluke
TECHNICAL- 8846A by Direct
ALTERNATING measure
CURRENT (< 1 GHZ)
(Measure)

4 ELECTRO- AC Current 50 Hz 100 micro A to 100 mA 2.0% to 0.6% Using 6 ½ DMM Fluke
TECHNICAL- 8846A by Direct
ALTERNATING measure
CURRENT (< 1 GHZ)
(Measure)

5 ELECTRO- AC High Voltage 1 kV to 100 kV 2.8% Using High Voltage

TECHNICAL- Divider with kV meter
ALTERNATING Make – Udeyraj by
CURRENT (< 1 GHZ) Direct/ Comparison
(Measure) method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 25 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

6 ELECTRO- AC Voltage50 Hz 1 V to 1000 V 0.5% to 0.11% Using 6 ½ DMM Fluke

TECHNICAL- 8846A by Direct
ALTERNATING measure
CURRENT (< 1 GHZ)
(Measure)

7 ELECTRO- AC Voltage50 Hz 10 mV to 100 mV 1.5% to 0.5% Using 6 ½ DMM Fluke

TECHNICAL- 8846A by Direct
ALTERNATING measure
CURRENT (< 1 GHZ)
(Measure)

8 ELECTRO- High Voltage 50Hz 1 kV to 20 kV 4.2% Using Motwane HV

TECHNICAL- Probe with DMM
ALTERNATING motwane By Direct
CURRENT (< 1 GHZ) measure
(Measure)

9 ELECTRO- AC Current 50Hz to 1 A to 10 A 0.16% to 0.15% Using Multifunction

TECHNICAL- 1kHz calibrator 5500A Fluke
ALTERNATING by Direct Method
CURRENT (< 1 GHZ)
(Source)

10 ELECTRO- AC Current 50Hz to 100 micro A to 1 A 0.45% to 0.16% Using Multifunction

TECHNICAL- 1kHz calibrator 5500A Fluke
ALTERNATING by Direct Method
CURRENT (< 1 GHZ)
(Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 26 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

11 ELECTRO- AC Current 50Hz to 100 micro A to 1 A 0.45% to 0.16% Using Multifunction

TECHNICAL- 1kHz calibrator 5500A Fluke
ALTERNATING by Direct Method
CURRENT (< 1 GHZ)
(Source)

12 ELECTRO- AC Power @50HzAt 0.5 (1V, 0.5A , UPF to 0.5% to 2.0% Using Multifunction
TECHNICAL- UPF to 0.2 PF 0.2 Lag)@ 50Hz 0.5W calibrator 5500A Fluke
ALTERNATING Watt to 6 ( 600V,10 A, by Direct Method
CURRENT (< 1 GHZ) UPF to 0.2 Lag)@
(Source) 50Hz Watt

13 ELECTRO- AC Power @50HzAt 0.5 (1V, 0.5A , UPF to 0.5% to 2.0% Using Multifunction
TECHNICAL- UPF to 0.2 PF 0.2 Lag)@ 50Hz 0.5W calibrator 5500A Fluke
ALTERNATING Watt to 6 ( 600V,10 A, by Direct Method
CURRENT (< 1 GHZ) UPF to 0.2 Lag)@
(Source) 50Hz Watt

14 ELECTRO- AC Voltage 50Hz to 10 mV to 10 V 0.45% to 0.06% Using multifunction

TECHNICAL- 1kHz calibrator 5500A Fluke
ALTERNATING by Direct Method
CURRENT (< 1 GHZ)
(Source)

15 ELECTRO- AC Voltage 50Hz to 10 V to 1000 V 0.06% to 0.1% Using Multifunction

TECHNICAL- 1kHz calibrator 5500A Fluke
ALTERNATING by Direct Method
CURRENT (< 1 GHZ)
(Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 27 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

16 ELECTRO- Phase Angle 0 ° to 90 ° 0.19° Using multifunction

TECHNICAL- calibrator 5500A Fluke
ALTERNATING by Direct Method
CURRENT (< 1 GHZ)
(Source)

17 ELECTRO- Power Factor 0.2 PF to 1 PF 0.17PF Using Multifunction

TECHNICAL- calibrator 5500A Fluke
ALTERNATING by Direct Method
CURRENT (< 1 GHZ)
(Source)

18 ELECTRO- DC Current 10 micro A to 10 A 0.7% to 0.2% Using 6 1/2 DMM Fluke

TECHNICAL- DIRECT 8846A by Direct
CURRENT (Measure) measure

19 ELECTRO- DC High Voltage 1 kV to 5 kV 2% Using motwane HV

TECHNICAL- DIRECT probe with DMM
CURRENT (Measure) motwane by direct
measure

20 ELECTRO- DC High Voltage 1 kV to 70 kV 2.0% Using High Voltage

TECHNICAL- DIRECT Divider with kV meter .
CURRENT (Measure) Make – Udeyraj by
Direct/ Comparison
method

21 ELECTRO- DC Voltage 1 mV to 100 mV 1.00% to 0.045% Using 6 1/2 DMM Fluke

TECHNICAL- DIRECT 8846A / Direct Measure
CURRENT (Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 28 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

22 ELECTRO- DC Voltage 100 mV to 1000 V 0.045% to 0.04% Using 6 1/2 DMM Fluke
TECHNICAL- DIRECT 8846A / Direct Measure
CURRENT (Measure)

23 ELECTRO- Low Resistance 1 m ohm to 10 ohm 1.1% Using 6.5 Digit DMM
TECHNICAL- DIRECT and fluke 5500A by V/ I
CURRENT (Measure) method.

24 ELECTRO- Resistance 10 ohm to 100 k ohm 0.7% to 0.2% Using 6 ½ DMM Fluke
TECHNICAL- DIRECT 8846A by Direct
CURRENT (Measure) measure

25 ELECTRO- Resistance 100 k ohm to 100 M 0.2% to 2.4% Using 6 ½ DMM Fluke
TECHNICAL- DIRECT ohm 8846A by Direct
CURRENT (Measure) measure

26 ELECTRO- Resistance 100 M ohm to 1 G ohm 2.9% Using 6 ½ DMM Fluke

TECHNICAL- DIRECT 8846A by Direct
CURRENT (Measure) measure

27 ELECTRO- DC Current 10 micro A to 100 0.6% to 0.07% Using multifunction

TECHNICAL- DIRECT micro A calibrator 5500A Fluke
CURRENT (Source) by Direct sourcing

28 ELECTRO- DC Current 100 mA to 10 A 0.02% to 0.09% Using multifunction

TECHNICAL- DIRECT calibrator 5500A Fluke
CURRENT (Source) by Direct sourcing

29 ELECTRO- DC Current 100 micro A to 100 mA 0.07% to 0.02% Using multifunction

TECHNICAL- DIRECT calibrator 5500A Fluke
CURRENT (Source) by Direct sourcing

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 29 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

30 ELECTRO- DC Voltage 1 mV to 10 mV 1.0% to 0.1% Using Multifunction

TECHNICAL- DIRECT calibrator 5500A Fluke
CURRENT (Source) by Direct sourcing

31 ELECTRO- DC Voltage 1 V to 1000 V 0.015% to 0.01% Using Multifunction

TECHNICAL- DIRECT calibrator 5500A Fluke
CURRENT (Source) by Direct sourcing

32 ELECTRO- DC Voltage 10 mV to 1 V 0.1% to 0.015% Using Multifunction

TECHNICAL- DIRECT calibrator 5500A Fluke
CURRENT (Source) by Direct sourcing

33 ELECTRO- Resistance 1 m ohm to 10 ohm 1.35% to 2.4% Using shunts & Decade
TECHNICAL- DIRECT Box Maxwell, Model
CURRENT (Source) DR 8 Direct sourcing

34 ELECTRO- Resistance 10 M ohm to 100 M 0.08% to 0.6% Using Multifunction

TECHNICAL- DIRECT ohm calibrator 5500 A Fluke
CURRENT (Source) by Direct sourcing

35 ELECTRO- Resistance 10 ohm to 100 k ohm 0.2% to 0.02% Using Multifunction

TECHNICAL- DIRECT calibrator 5500 A Fluke
CURRENT (Source) by Direct sourcing

36 ELECTRO- Resistance 100 k ohm to 10 M ohm 0.02% to 0.08% Using Multifunction

TECHNICAL- DIRECT calibrator 5500 A Fluke
CURRENT (Source) by Direct sourcing

37 ELECTRO- Resistance 100 M ohm to 300 M 0.6% to 1.0% Using Multifunction

TECHNICAL- DIRECT ohm calibrator 5500 A Fluke
CURRENT (Source) by Direct sourcing

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 30 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

38 ELECTRO- Resistance 300 M ohm to 100 G 3.4% Using Mega Ohm Box
TECHNICAL- DIRECT ohm Maxwell, Model DB 231
CURRENT (Source) for calibration of
Meggers upto 5kV by
Direct method

39 ELECTRO- B type Thermocouples 600 ° C to 1750 ° C 0.75° C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION
(Measure)

40 ELECTRO- E type Thermocouple -200 ° C to 1000 ° C 0.44° C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION
(Measure)

41 ELECTRO- J type Thermocouple -200 °C to 750 °C 0.2°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION
(Measure)

42 ELECTRO- K type Thermocouple -200 °C to 1350 °C 0.25°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 31 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

43 ELECTRO- N type Thermocouple 50 °C to 1750 °C 0.75°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION
(Measure)

44 ELECTRO- R type Thermocouple 50 °C to 1750 °C 0.41°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION
(Measure)

45 ELECTRO- RTD -200 °C to 800 °C 0.35°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION
(Measure)

46 ELECTRO- S type Thermocouple 50 °C to 1750 °C 0.70°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION
(Measure)

47 ELECTRO- T type Thermocouple -200 °C to 400 °C 0.27°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 32 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

48 ELECTRO- B type Thermocouple 600 ° C to 1750 ° C 0.75° C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION (Source)

49 ELECTRO- E type Thermocouples -200 ° C to 1000 ° C 0.75° C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION (Source)

50 ELECTRO- J type Thermocouples -200 °C to 750 °C 0.75°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION (Source)

51 ELECTRO- K type Thermocouples -200 °C to 1350 °C 0.75°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION (Source)

52 ELECTRO- N type Thermocouples 50 °C to 1750 °C 0.75°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION (Source)

53 ELECTRO- R type Thermocouples 50 °C to 1750 °C 0.75°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION (Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 33 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

54 ELECTRO- RTD -200 °C to 800 °C 0.35°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION (Source)

55 ELECTRO- S type Thermocouples 50 °C to 1750 °C 0.75°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION (Source)

56 ELECTRO- T type Thermocouples -200 °C to 400 °C 0.75°C Using Radix / Fluke

TECHNICAL- Multifunction calibrator
TEMPERATURE by Simulation method
SIMULATION (Source)

57 ELECTRO- Capacitance 1kHz 1 nF to 100 micro F 3% to 0.7% Using 6 ½ DMM Fluke

TECHNICAL- TIME & 8846A by Direct
FREQUENCY measure
(Measure)

58 ELECTRO- Capacitance 1kHz 100 micro F to 300 0.7% to 1.2% Using 6 ½ DMM Fluke
TECHNICAL- TIME & micro F 8846A by Direct
FREQUENCY measure
(Measure)

59 ELECTRO- Capacitance 1kHz 100 micro F to 300 0.7% to 1.2% Using 6 ½ DMM Fluke
TECHNICAL- TIME & micro F 8846A by Direct
FREQUENCY measure
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 34 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

60 ELECTRO- Digital / Analog Stop 10 sec to 59 min 1.51sec to 2sec Using Digital Time
TECHNICAL- TIME & Watch / Timer interval meter by
FREQUENCY Comparison Method
(Measure)

61 ELECTRO- Frequency 10 Hz to 1 M Hz 0.8%% to 1.40% Using 6 ½ DMM Fluke

TECHNICAL- TIME & 8846A by Direct
FREQUENCY measure
(Measure)

62 ELECTRO- Capacitance 1kHz 0.5 n F to 100 micro F 3% to 0.7% Using Multifunction

TECHNICAL- TIME & calibrator 5500A Fluke
FREQUENCY (Source) by Direct Method

63 ELECTRO- Capacitance 1kHz 100 micro F to 300 0.7% to 1.2% Using Multifunction
TECHNICAL- TIME & micro F calibrator 5500A Fluke
FREQUENCY (Source) by Direct Method

64 ELECTRO- Frequency 10 Hz to 100 k Hz 0.015% to 0.065% Using Multifunction

TECHNICAL- TIME & calibrator 5500A Fluke
FREQUENCY (Source) by Direct Method

65 MECHANICAL- Profile Projector (Linear upto to 200 mm 2.5µm Using Slip Gauge Set
DIMENSION (BASIC Scale) L.C. 0.001 mm
MEASURING
INSTRUMENT,
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 35 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

66 MECHANICAL- Profile Projector upto to 360 deg 3 Min of arc Using Slip Gauge Set,
DIMENSION (BASIC (Angular Scale) L.C. 1 Angle Gauge,
MEASURING Min Cylindrical Pin by
INSTRUMENT, Comparison Method
GAUGE ETC.)

67 MECHANICAL- Profile Projector 10X to 100X 0.2% Using Slip Gauge Set,
DIMENSION (BASIC (Magnification) Angle Gauge,
MEASURING Cylindrical Pin by
INSTRUMENT, Comparison Method
GAUGE ETC.)

68 MECHANICAL- Straight Edge Up to 2 mtr 18 µm Using Slip Gauge Set,

DIMENSION (BASIC Surface Plate, Spirit
MEASURING Level & Feeler Gauge
INSTRUMENT,
GAUGE ETC.)

69 MECHANICAL- Surface Plate 3000 to 3000 mm 3 µm Using Spirit Level

DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)

70 MECHANICAL- Hydraulic Pressure 0 bar to 30 bar 0.8% of rdg to 0.8% of Using Digital Pressure
PRESSURE Gauge / Digital / rdg Gauge
INDICATING DEVICES Analog Pressure
Gauge / Pressure
Indicator

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 36 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

71 MECHANICAL- Hydraulic Pressure 30 bar to 600 bar 0.8% of rdg to 0.8% of Using digital pressure
PRESSURE Gauge / Digital / rdg gauge
INDICATING DEVICES Analog Pressure
Gauge / Pressure
Indicator

72 MECHANICAL- Vacuum Gauge / (-) 0.9 bar to 0 bar 0.8% of rdg to 0.8% of Using Digital Vacuum
PRESSURE Indicator rdg Gauge by Direct
INDICATING DEVICES Comparison DKD-R-6-
1

73 MECHANICAL- UTM, Verification of Uniaxial 100kN to 500kN 0.60% Using class I range of
TENSION CREEP Testing Machines Force Proving
AND TORSION Compression Instrument
TESTING MACHINE

74 MECHANICAL- UTM, Verification of Uniaxial 100N to 10kN 0.65% Using Standards

TENSION CREEP Testing Machines Newton Weights (True
AND TORSION Tension Mode Force Method), Using
TESTING MACHINE Class I range of Force
Proving Instrument

75 MECHANICAL- UTM, Verification of Uniaxial 10kN to 100kN 0.65% Using Standards

TENSION CREEP Testing Machines Newton Weights (True
AND TORSION Tension Mode Force Method), Using
TESTING MACHINE Class I range of Force
Proving Instrument

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 37 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

76 MECHANICAL- UTM, Verification of Uniaxial 1N to 100N 0.65% Using Standards

TENSION CREEP Testing Machines Newton Weights (True
AND TORSION Tension Mode Force Method) Class I
TESTING MACHINE range of Force Proving
Instrument

77 MECHANICAL- Electronic Weighing 5g to 80 g 0.03mg Using Standard E1

WEIGHING SCALE Balance Class Weights
AND BALANCE

78 MECHANICAL- Electronic Weighing >300g to 3kg 40mg Using Standard F2

WEIGHING SCALE Balance Class Weights L.C. 0.1
AND BALANCE g

79 MECHANICAL- Electronic Weighing >3kg to 30kg 2g Using F2 Class

WEIGHING SCALE Balance Weights L.C. 1 g
AND BALANCE

80 MECHANICAL- Electronic Weighing 80g to 200 g 0.3mg Using Standard E1

WEIGHING SCALE Balance Class Weights
AND BALANCE

81 MECHANICAL- Electronic Weighing up to 5g 0.03mg Using Standard E1

WEIGHING SCALE Balance Class Weights
AND BALANCE

82 THERMAL- SPECIFIC Humidity indicator of 20% RH to 95% RH @ 1.9% RH Using digital

HEAT & HUMIDITY RH Chamber 25 degree C Hygrometer single
position calibration (at
measuring location in
DUC)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 Laboratory Name CALI LABS PVT LTD, HX 21 E 7, ARERA COLONY, BHOPAL, MADHYA PRADESH ,
INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2280 Page No. : 38 / 38

Validity 30/06/2019 to 29/06/2021 Last Amended on -

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or

Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

83 THERMAL- RTD / Thermocouple -25 degree C to 300 0.22 degree C Using RTD (Pt 100), 6
TEMPERATURE With or Without degree C 1/2 DMM & Dry Block
Temperature Indicator, Calibrator
Dial / Digital
Thermometer

84 THERMAL- Temperature Indicator 30 degree C to 250 1.2 degree C Using RTD (Pt 100), , 6
TEMPERATURE with sensor of Freezer, degree C 1/2 DMM multiple
Oven, Chamber, position calibration (at
Furnace measuring location in
DUC)

85 THERMAL- Temperature Indicator 300 degree C to 1000 1.9 degree C Using RTD (Pt 100), S
TEMPERATURE with sensor of Oven, degree C type Thermocouple, 6
Chamber, Furnace 1/2 DMM multiple
position calibration (at
measuring location in
DUC)

86 THERMAL- Thermocouple With or 300 degree C to 500 1.8 degree C S type Thermocouple,
TEMPERATURE Without Temperature degree C 6 1/2 DMM & Dry Block
Indicator, Dial / Digital Calibrator
Thermometer

* CMCs represent expanded uncertainties expressed at approximately the 95% level of confidence, using a coverage factor of k = 2.

This is annexure to 'Certificate of Accreditation' and does not require any signature.