FUNDAMENTAL OF ENGINEERING

GRAPHICS

1
 Introduction

Introduction

Engineering Graphics is a language of

communication between engineers on an
international basis.

The beauty of this tool of communication is that it

transfers 100% of information between technical
people.

A graphical presentation is more than an essay for

describing the same thing.
2
Introduction

3
Introduction

4
 Dr. Vikas J. Patel
Mechanical Engg. Department,
Drawing Instruments and simple geometry Associate Professor,
CKPCET

Basic Instruments.
(i) Drawing board (ii) Drawing sheet
(iii) Drawing pencil (iv) Drawing clips
(v) Eraser (vi) Eraser shield

5
 Dr. Vikas J. Patel
Mechanical Engg. Department,
Associate Professor,
CKPCET

Instruments for Drawing Straight Lines.

(i) T- square. (ii) Set- squares
Instruments for Drawing Curved Lines.
(i) Large size compass (ii) Small bow
(iii) French curve
Instruments for Measuring Distance.
(i) Large size divider (ii) Small bow
divider
(iii) Scales
Instruments for Measuring Angles.
(i) Protractors (ii) Set-squares
Special Tool. Mini drafter
6
 Dr. Vikas J. Patel
Mechanical Engg. Department,
Associate Professor,
CKPCET

7
 Dr. Vikas J. Patel
Mechanical Engg. Department,
Associate Professor,
CKPCET

T- Square
It is composed of a long strip called blade, which is screwed
rigidly at right angle to a shorter piece called head or stock. It is
made of mahogany or pear wood, which is harder than the board
wood. The head also has an ebony edge which slides against the
working edge of the board. T- Square is used for making
horizontal, vertical, inclined or parallel lines on the drawing sheet.

8
 Dr. Vikas J. Patel
Mechanical Engg. Department,
Associate Professor,
CKPCET

Neatness, quality and accuracy of the drawing greatly depends upon

the type and conditions of the pencil used for drawing.

(a) Hard : 9H to 4H
(b) Medium : 3H to B (3H, 2H, H, F, HB and B)
(c) Soft : 2B to 7B

Following pencils should be used for drawing work in class:

2H Pencil - For drawing outlines, Centre lines, Break lines, etc.

H Pencil - For dimensioning, arrowheads, hatching lines, lettering,

sketching, circles, arcs, etc.

Micro tip pencil - 0.5mm for drawing outlines and 0.8mm for shading
and sketching

9
Engineering Graphics

Drawing sheet, types of

line, Lettering and
Dimensioning

(As per BIS : SP : 46 : 2003)

10
Pencils:

Pencils with leads of different degrees of hardness or grades are available in

the market. The hardness or softness of the lead is indicated by 3H, 2H, H,
HB, B, 2B, 3B, etc. The grade HB denotes medium hardness of lead used for
general purpose. The hardness increases as the value of the numeral before
the letter H increases. The lead becomes softer, as the value of the numeral
before B increases.

Pencils leads

11
The selection of the grade depends on the line quality desired for the drawing.
Pencils of grades H or 2H may be used for finishing a pencil drawing as these give a
sharp black line. Softer grade pencils are used for sketching work. HB grade is
recommended for lettering and dimensioning.
Nowadays mechanical pencils are widely used in place of wooden pencils.
When these are used, much of the sharpening time can be saved. The number
0.5,0.70 of the pen indicates the thickness of the line obtained with the lead and the
size of the lead diameter.
Micro-tip pencils with 0.5 mm thick leads with the following grades are
recommended.
HB Soft grade for Border lines, lettering and free sketching H Medium grade
for Visible outlines, visible edges and boundary lines 2H Hard grade for construction
lines, Dimension lines, Leader lines, Extension lines, Centre lines, Hatching lines and
Hidden lines.

Mechanical Pencils

12
Drawing Sheet

The standard drawing sheet sizes are arrived at on the basic Principal of x: y
= 1 : √2 and xy = 1 where x and yare the sides of the sheet. For example AO,
having a surface area of 1 Sq. m; x = 841 rom and y = 1189 mm. The
successive sizes are obtained by either by halving along the length or
doubling the width, the area being in the ratio 1 : 2. Designation of sizes is
given in Figure and their sizes are given in Table. For class work use of A2 size
drawing sheet is preferred.

Designation Dimension, mm
Trimmed size
A0 841 × 1189
A1 594 × 841
A2 420 × 594
A3 297 × 420
A4 210 × 297

Drawing sheet formats 13

Drawing Sheet Layout:

A proper sheet layout is necessary for the easy reading of the drawing. The
following are the important features considered while layout a drawing
sheet.

1. Sheet size:
students are advised to use A3 or A4 size of sheet.

2. Boarder lines:
boarder lines are used to obtain clear working space on the
drawing sheet. Boarder lies should be drawn 10 mm inside edges of the
drawing sheet.

3. Title block:
Space for the title block must be provided in the bottom right
corner of the drawing sheet as shown in figure. The size of the title block
varies depending upon the contents to be filled in it. The size of the title
block for drawing in colleges is recommended by the B.I.S.as 185 mm × 65
mm.

14
Drawing Sheet Layout

15
Title Block

The title block should lie within the drawing space at the bottom right hand
comer of the sheet. The title block can have a maximum length of 170 mm
providing the following information.

1. Title of the drawing.

2. Drawing number.
3. Scale.
4. Symbol denoting the method of projection.
5. Name of the firm, and
6. Initials of staff who have designed, checked and approved.

The title block used on shop floor and one suggested for students class work
are shown in

16
Title Block

17
Title Block

Title block
for
Shop floor

Title block
for
Student
work

18
 ❑ Standard and convention:

Engineering drawing is language of engineers. Every language follows a standard set

of rules which make communication between people easier. Engineering drawing must follow a
set of standards and conventions in order to make communication between engineers effective.

IS 1444: 1989 ENGINEER’S PATTERN DRAWING BOARD- SPECIFICATION

IS 10711: 2001 TECHNICAL PRODUCT DOCUMENTATION SIZES AND LAYOUT OF DRAWING SHEETS
IS 3221: 1966 SETS FOR DRAWING INSTRUMENTS
IS 10713: 1983 SCALES
IS 10714: 2001 LINES
IS 96009: 2001 LETTERING
IS 15021: 2001 PROJECTION METHODS
IS 10714: 1983 SECTIONS AND OTHER CONVENTIONS
IS 1169: 1986 GENERAL PRINCIPLES OF DIMENSIONS ON TECHNICAL DRAWING 19
❑ Types of line and their applications:
In engineering drawing, the various types of lines are recommended by
B.I.S. with different thickness. But for general students are advised to take 0.5
mm for thick lines, 0.3 mm for medium lines and 0.2 mm for thin lines.

20
❑ Types of line and their applications:
Visible Outlines, Visible Edges : (Continuous wide lines) The lines drawn to represent
the visible outlines/ visible edges / surface boundary lines of objects should be
outstanding in appearance.
Dimension Lines: (Continuous narrow Lines) Dimension Lines are drawn to mark
dimension.
Extension Lines: (Continuous narrow Lines) There are extended slightly beyond the
respective dimension lines.
Construction Lines: (Continuous narrow Lines) Construction Lines are drawn for
constructing drawings and should not be erased after completion of the drawing.
Hatching / Section Lines: (Continuous Narrow Lines) Hatching Lines are drawn for
the sectioned portion of an object. These are drawn inclined at an angle of 45° to
the axis or to the main outline of the section.
Guide Lines: (Continuous Narrow Lines) Guide Lines are drawn for lettering and
should not be erased after lettering.
Break Lines: (Continuous Narrow Freehand Lines) Wavy continuous narrow line
drawn freehand is used to represent break of an object.
Break Lines : (Continuous Narrow Lines With Zigzags) Straight continuous narrow
line with zigzags is used to represent break of an object.

21
❑ Types of line and their applications:
Dashed Narrow Lines: (Dashed Narrow Lines) Hidden edges / Hidden outlines of
objects are shown by dashed lines of short dashes of equal lengths of about 3
mm, spaced at equal distances of about 1 mm. the points of intersection of these
lines with the outlines / another hidden line should be clearly shown.
Center Lines: (Long-Dashed Dotted Narrow Lines) Center Lines are drawn at the
center of the drawings symmetrical about an axis or both the axes. These are
extended by a short distance beyond the outline of the drawing.
Cutting Plane Lines: Cutting Plane Line is drawn to show the location of a cutting
plane. It is long-dashed dotted narrow line, made wide at the ends, bends and
change of direction. The direction of viewing is shown by means of arrows resting
on the cutting plane line.
Border Lines: Border Lines are continuous wide lines of minimum thickness 0.7
mm

Line Widths:
Line width means line thickness.
Choose line widths according to the size of the drawing from the
following range: 0.13,0.18, 0.25, 0.35, 0.5, 0.7 and 1 mm.
BIS recommends two line widths on a drawing. Ratio between the thin
and thick lines on a drawing shall not be less than 1 : 2.
22
❑ Types of line and their applications:

23
❑ Lettering:

24
❑ Lettering:

25
❑ Lettering:

26
❑ Lettering guide lines and grids:

27
❑ Lettering:

28
❑ Single-stroke vertical Lettering:

29
❑ Single-stroke vertical Lettering:

30
❑ Single-stroke Inclined Lettering:

31
❑ Single-stroke Inclined Lettering:

32
❑ Double-stroke Vertical Lettering:

33
❑ Double-stroke Vertical Lettering:

34
❑ Double-stroke Inclined Lettering:

35
❑ Double-stroke Inclined Lettering:

36
❑ Normal, Compresses and Expanded letters:

❑ Rules of Lettering:

37
❑ Dimensioning:

38
❑ Dimensioning:

39
❑ Dimensioning:

40
❑ System of Dimensioning:
There are two systems of dimensioning:
1. Aligned System
2. Unidirectional system

Aligned System
In the aligned system, dimensions are aligned with the entity being measured.
They are placed perpendicular to the dimension line such that they may be read
from the bottom or right-hand side of the drawing sheet. Dimensions are placed
at the middle and on top of the dimension lines.

Unidirectional System
In the unidirectional system, dimensions are placed in such a way that they can
be read from the bottom edge of the drawing sheet. Dimensions are inserted by
breaking the dimension lines at the middle.

41
❑ System of Dimensioning:
Aligned System:

42
❑ System of Dimensioning:
Unidirectional System:

43
❑ System of Dimensioning:
In Aligned System its is divided in to the two sub parts Parallel, Chain
and Combined Dimensioning:

Parallel Dimensioning Chain Dimensioning

44
❑ System of Dimensioning:
In Aligned System its is divided in to the two sub parts Parallel, Chain
and Combined Dimensioning:

Combined Dimensioning

45
❑ Practical Hints on Dimensioning:

Combined Dimensioning

46
❑ Practical Hints on Dimensioning:

47
❑ Practical Hints on Dimensioning:

48
❑ Practical Hints on Dimensioning:

49
❑ Practical Hints on Dimensioning:

50
❑ Practical Hints on Dimensioning:

51
❑ Practical Hints on Dimensioning:

52
❑ Practical Hints on Dimensioning:

53
 Dr. Vikas J. Patel
Mechanical Engg. Department,
Associate Professor,
CKPCET

54
SCALES

55
 SCALES

DIMENSIONS OF LARGE OBJECTS MUST BE REDUCED TO ACCOMMODATE

ON STANDARD SIZE DRAWING SHEET.THIS REDUCTION CREATES A SCALE FOR FULL SIZE SCALE
OF THAT REDUCTION RATIO, WHICH IS GENERALLY A FRACTION.. R.F.=1 OR ( 1:1 )
SUCH A SCALE IS CALLED REDUCING SCALE MEANS DRAWING
AND & OBJECT ARE OF
THAT RATIO IS CALLED REPRESENTATIVE FACTOR. SAME SIZE.
Other RFs are described
SIMILARLY IN CASE OF TINY OBJECTS DIMENSIONS MUST BE INCREASED as
FOR ABOVE PURPOSE. HENCE THIS SCALE IS CALLED ENLARGING SCALE. 1:10, 1:100,
1:1000, 1:1,00,000
HERE THE RATIO CALLED REPRESENTATIVE FACTOR IS MORE THAN UNITY.

USE FOLLOWING FORMULAS FOR THE CALCULATIONS IN THIS TOPIC.

DIMENSION OF DRAWING
A REPRESENTATIVE FACTOR (R.F.) =
DIMENSION OF OBJECT
LENGTH OF DRAWING
=
ACTUAL LENGTH
AREA OF DRAWING
=
V ACTUAL AREA
VOLUME AS PER DRWG.
= 3
V ACTUAL VOLUME

B LENGTH OF SCALE = R.F. X LENGTH TO BE MEASURED.

MAX.
56
 BE FRIENDLY WITH THESE UNITS.

1 KILOMETRE = 10 HECTOMETRES
1 HECTOMETRE = 10 DECAMETRES
1 DECAMETRE = 10 METRES
1 METRE = 10 DECIMETRES
1 DECIMETRE = 10 CENTIMETRES
1 CENTIMETRE = 10 MILIMETRES

TYPES OF SCALES:
1. PLAIN SCALES ( FOR DIMENSIONS UP TO SINGLE DECIMAL)
2. DIAGONAL SCALES ( FOR DIMENSIONS UP TO TWO DECIMALS)
3. VERNIER SCALES ( FOR DIMENSIONS UP TO TWO DECIMALS)
4. COMPARATIVE SCALES ( FOR COMPARING TWO DIFFERENT UNITS)
5. SCALE OF CORDS ( FOR MEASURING/CONSTRUCTING ANGLES)

57
 PLAIN SCALE:- This type of scale represents two units or a unit and it’s sub-division.
PROBLEM NO.1:- Draw a scale 1 cm = 1m to read decimeters, to measure maximum distance of 6 m.
Show on it a distance of 4 m and 6 dm.

CONSTRUCTION:- DIMENSION OF DRAWING

PLAIN SCALE
a) Calculate R.F.=
DIMENSION OF OBJECT

R.F.= 1cm/ 1m = 1/100

Length of scale = R.F. X max. distance
= 1/100 X 600 cm
= 6 cms
b) Draw a line 6 cm long and divide it in 6 equal parts. Each part will represent larger division unit.
c) Sub divide the first part which will represent second unit or fraction of first unit.
d) Place ( 0 ) at the end of first unit. Number the units on right side of Zero and subdivisions
on left-hand side of Zero. Take height of scale 5 to 10 mm for getting a look of scale.
e) After construction of scale mention it’s RF and name of scale as shown.
f) Show the distance 4 m 6 dm on it as shown.

4 M 6 DM

10 0 1 2 3 4 5 METERS
DECIMETERS
R.F. = 1/100
PLANE SCALE SHOWING METERS AND DECIMETERS.
58
 PROBLEM NO.2:- In a map a 36 km distance is shown by a line 45 cms long. Calculate the R.F. and construct
a plain scale to read kilometers and hectometers, for max. 12 km. Show a distance of 8.3 km on it.

CONSTRUCTION:-
a) Calculate R.F.
R.F.= 45 cm/ 36 km = 45/ 36 . 1000 . 100 = 1/ 80,000
PLAIN SCALE
Length of scale = R.F. max. distance
= 1/ 80000 12 km
= 15 cm
b) Draw a line 15 cm long and divide it in 12 equal parts. Each part will represent larger division unit.
c) Sub divide the first part which will represent second unit or fraction of first unit.
d) Place ( 0 ) at the end of first unit. Number the units on right side of Zero and subdivisions
on left-hand side of Zero. Take height of scale 5 to 10 mm for getting a look of scale.
e) After construction of scale mention it’s RF and name of scale as shown.
f) Show the distance 8.3 km on it as shown.

8KM 3HM

10 5 0 1 2 3 4 5 6 7 8 9 10 11
KILOMETERS
HECTOMETERS
R.F. = 1/80,000
PLANE SCALE SHOWING KILOMETERS AND HECTOMETERS
59
PROBLEM NO.3:- The distance between two stations is 210 km. A passenger train covers this distance
in 7 hours. Construct a plain scale to measure time up to a single minute. RF is 1/200,000 Indicate the distance
traveled by train in 29 minutes.

CONSTRUCTION:-
a) 210 km in 7 hours. Means speed of the train is 30 km per hour ( 60 minutes)
PLAIN SCALE
Length of scale = R.F. max. distance per hour
= 1/ 2,00,000 30km
= 15 cm
b) 15 cm length will represent 30 km and 1 hour i.e. 60 minutes.
Draw a line 15 cm long and divide it in 6 equal parts. Each part will represent 5 km and 10 minutes.
c) Sub divide the first part in 10 equal parts,which will represent second unit or fraction of first unit.
Each smaller part will represent distance traveled in one minute.
d) Place ( 0 ) at the end of first unit. Number the units on right side of Zero and subdivisions
on left-hand side of Zero. Take height of scale 5 to 10 mm for getting a proper look of scale.
e) Show km on upper side and time in minutes on lower side of the scale as shown.
After construction of scale mention it’s RF and name of scale as shown.
f) Show the distance traveled in 29 minutes, which is 14.5 km, on it as shown.
DISTANCE TRAVELED IN 29 MINUTES.
14.5 KM

KM 5 2.5 0 5 10 15 20 25 KM

MIN 10 0 10 20 30 40 50 MINUTES
R.F. = 1/100
PLANE SCALE SHOWING METERS AND DECIMETERS.
60
 We have seen that the plain scales give only two dimensions, such as a
unit and it’s subunit or it’s fraction.
DIAGONAL
The diagonal scales give us three successive dimensions
that is a unit, a subunit and a subdivision of a subunit. SCALE

The principle of construction of a diagonal scale is as follows.

Let the XY in figure be a subunit. X
Y
From Y draw a perpendicular YZ to a suitable height. 10
Join XZ. Divide YZ in to 10 equal parts. 9
Draw parallel lines to XY from all these divisions
8
and number them as shown.
From geometry we know that similar triangles have 7
their like sides proportional. 6
5
Consider two similar triangles XYZ and 7’ 7Z, 4
we have 7Z / YZ = 7’7 / XY (each part being one unit)
3
Means 7’ 7 = 7 / 10. x X Y = 0.7 XY
:. 2
Similarly 1
1’ – 1 = 0.1 XY
2’ – 2 = 0.2 XY Z
Thus, it is very clear that, the sides of small triangles,
which are parallel to divided lines, become progressively
shorter in length by 0.1 XY.

The solved examples ON NEXT PAGES will

make the principles of diagonal scales clear. 61
 PROBLEM NO. 4 : The distance between Delhi and Agra is 200 km.
In a railway map it is represented by a line 5 cm long. Find it’s R.F.
Draw a diagonal scale to show single km. And maximum 600 km.
DIAGONAL
Indicate on it following distances. 1) 222 km 2) 336 km 3) 459 km 4) 569 km SCALE
SOLUTION STEPS: RF = 5 cm / 200 km = 1 / 40, 00, 000
Length of scale = 1 / 40, 00, 000 X 600 X 10 5 = 15 cm

Draw a line 15 cm long. It will represent 600 km.Divide it in six equal parts.( each will represent 100 km.)
Divide first division in ten equal parts.Each will represent 10 km.Draw a line upward from left end and
mark 10 parts on it of any distance. Name those parts 0 to 10 as shown.Join 9th sub-division of horizontal scale
with 10th division of the vertical divisions. Then draw parallel lines to this line from remaining sub divisions and
complete diagonal scale.
569 km
459 km
336 km
222 km
10
9
8
7
6
KM

5
4
3
2
1
0
KM
100 50 0 100 200 300 400 500 KM
R.F. = 1 / 40,00,000

DIAGONAL SCALE SHOWING KILOMETERS. 62

 PROBLEM NO.5: A rectangular plot of land measuring 1.28 hectors is represented on a map by a similar rectangle
of 8 sq. cm. Calculate RF of the scale. Draw a diagonal scale to read single meter. Show a distance of 438 m on it.

SOLUTION : DIAGONAL
1 hector = 10, 000 sq. meters SCALE
1.28 hectors = 1.28 X 10, 000 sq. meters
Draw a line 15 cm long.
= 1.28 X 104 X 104 sq. cm
8 sq. cm area on map represents It will represent 600 m.Divide it in six equal parts.
= 1.28 X 104 X 104 sq. cm on land ( each will represent 100 m.)
1 cm sq. on map represents Divide first division in ten equal parts.Each will
= 1.28 X 10 4 X 104 / 8 sq cm on land represent 10 m.
1 cm on map represent Draw a line upward from left end and
mark 10 parts on it of any distance.
= 1.28 X 10 4 X 104 / 8 cm
Name those parts 0 to 10 as shown.Join 9th sub-division
= 4, 000 cm of horizontal scale with 10th division of the vertical divisions.
1 cm on drawing represent 4, 000 cm, Means RF = 1 / 4000 Then draw parallel lines to this line from remaining sub divisions
Assuming length of scale 15 cm, it will represent 600 m. and complete diagonal scale.
438 meters

10
9
8
7
6
5
M

4
3
2
1
0
M 100 50 0 100 200 300 400 500 M
R.F. = 1 / 4000

DIAGONAL SCALE SHOWING METERS. 63

COMPARATIVE SCALES: EXAMPLE NO. 7 :
These are the Scales having same R.F. A distance of 40 miles is represented by a line
but graduated to read different units. 8 cm long. Construct a plain scale to read 80 miles.
These scales may be Plain scales or Diagonal scales Also construct a comparative scale to read kilometers
and may be constructed separately or one above the other. upto 120 km ( 1 m = 1.609 km )

SOLUTION STEPS:
CONSTRUCTION:
Scale of Miles:
Take a line 16 cm long and divide it into 8 parts. Each will represent 10 miles.
40 miles are represented = 8 cm
Subdivide the first part and each sub-division will measure single mile.
: 80 miles = 16 cm
R.F. = 8 / 40 X 1609 X 1000 X 100
= 1 / 8, 04, 500

Scale of Km: CONSTRUCTION:

Length of scale On the top line of the scale of miles cut off a distance of 14.90 cm and divide
= 1 / 8,04,500 X 120 X 1000 X 100 it into 12 equal parts. Each part will represent 10 km.
= 14. 90 cm Subdivide the first part into 10 equal parts. Each subdivision will show single km.

10 0 10 20 30 40 50 60 70 80 90 100 110 KM
5

10 5 0 10 20 30 40 50 60 70 MILES

R.F. = 1 / 804500
COMPARATIVE SCALE SHOWING MILES AND KILOMETERS

64
Example 10:
Draw a vernier scale of RF = 1 / 25 to read centimeters upto Vernier Scale
4 meters and on it, show lengths 2.39 m and 0.91 m

SOLUTION: CONSTRUCTION: ( vernier)

Length of scale = RF X max. Distance Take 11 parts of Dm length and divide it in 10 equal parts.
= 1 / 25 X 4 X 100 Each will show 0.11 m or 1.1 dm or 11 cm and construct a rectangle
= 16 cm Covering these parts of vernier.
CONSTRUCTION: ( Main scale)
Draw a line 16 cm long. TO MEASURE GIVEN LENGTHS:
Divide it in 4 equal parts. (1) For 2.39 m : Subtract 0.99 from 2.39 i.e. 2.39 - .99 = 1.4 m
( each will represent meter ) The distance between 0.99 ( left of Zero) and 1.4 (right of Zero) is 2.39 m
Sub-divide each part in 10 equal parts. (2) For 0.91 m : Subtract 0.11 from 0.91 i.e. 0.91 – 0.11 =0.80 m
( each will represent decimeter ) The distance between 0.11 and 0.80 (both left side of Zero) is 0.91 m
Name those properly.

2.39 m

0.91 m

1.1 .99 .77 .55 .33 .11 0

1.0 .9 .8 .7 .6 .5 .4 .3 .2 .1 0 1 1.4 2 3 METERS

METERS

65
ENGNIEERING CURVES 1 & 2

66
 ENGINEERING CURVES
Part- I {Conic Sections}

ELLIPSE PARABOLA HYPERBOLA

1.Concentric Circle Method 1.Rectangle Method 1.Rectangular Hyperbola

(coordinates given)
2.Rectangle Method 2 Method of Tangents
( Triangle Method) 2 Rectangular Hyperbola
3.Oblong Method (P-V diagram - Equation given)
3.Basic Locus Method
4.Arcs of Circle Method (Directrix – focus) 3.Basic Locus Method
(Directrix – focus)
5.Rhombus Metho

6.Basic Locus Method Methods of Drawing

(Directrix – focus) Tangents & Normals
To These Curves.

67
 CONIC SECTIONS
ELLIPSE, PARABOLA AND HYPERBOLA ARE CALLED CONIC SECTIONS
BECAUSE
THESE CURVES APPEAR ON THE SURFACE OF A CONE
WHEN IT IS CUT BY SOME TYPICAL CUTTING PLANES.
OBSERVE
ILLUSTRATIONS
GIVEN BELOW..

Ellipse

Section Plane Section Plane

Through Generators Hyperbola
Parallel to Axis.

Section Plane Parallel

to end generator.
68
 COMMON DEFINATION OF ELLIPSE, PARABOLA & HYPERBOLA:
These are the loci of points moving in a plane such that the ratio of it’s distances
from a fixed point And a fixed line always remains constant.
The Ratio is called ECCENTRICITY. (E)
A) For Ellipse E<1
B) For Parabola E=1
C) For Hyperbola E>1

Refer Problem nos. 6. 9 & 12

SECOND DEFINATION OF AN ELLIPSE:-
It is a locus of a point moving in a plane
such that the SUM of it’s distances from TWO fixed points
always remains constant.
{And this sum equals to the length of major axis.}
These TWO fixed points are FOCUS 1 & FOCUS 2
Refer Problem no.4
Ellipse by Arcs of Circles Method. 69
 ELLIPSE
BY CONCENTRIC CIRCLE METHOD
Problem 1 :-
Draw ellipse by concentric circle method.
Take major axis 100 mm and minor axis 70 mm long. 3
2 4
Steps:
1. Draw both axes as perpendicular bisectors C
of each other & name their ends as shown.
2. Taking their intersecting point as a center, 1 5
3
2 4
draw two concentric circles considering both
as respective diameters.
1 5
3. Divide both circles in 12 equal parts &
name as shown.
A B
4. From all points of outer circle draw vertical
lines downwards and upwards respectively.
5.From all points of inner circle draw 10 6
horizontal lines to intersect those vertical
lines. 10 9 7 6
6. Mark all intersecting points properly as 8
those are the points on ellipse. D
7. Join all these points along with the ends of
both axes in smooth possible curve. It is 9 7
required ellipse.
8

70
Steps:
ELLIPSE
BY RECTANGLE METHOD
1 Draw a rectangle taking major
and minor axes as sides.
2. In this rectangle draw both Problem 2
axes as perpendicular bisectors of
Draw ellipse by Rectangle method.
each other..
3. For construction, select upper Take major axis 100 mm and minor axis 70 mm long.
left part of rectangle. Divide
vertical small side and horizontal
long side into same number of D 4
4
equal parts.( here divided in four
parts) 3 3
4. Name those as shown..
5. Now join all vertical points 2 2
1,2,3,4, to the upper end of minor
1 1
axis. And all horizontal points
i.e.1,2,3,4 to the lower end of
minor axis. A B
6. Then extend C-1 line upto D-1
and mark that point. Similarly
extend C-2, C-3, C-4 lines up to
D-2, D-3, & D-4 lines.
7. Mark all these points properly
and join all along with ends A
and D in smooth possible curve.
Do similar construction in right C
side part.along with lower half of
the rectangle.Join all points in
smooth curve.
71
It is required ellipse.
 ELLIPSE
Problem 3:- BY OBLONG METHOD
Draw ellipse by Oblong method.
Draw a parallelogram of 100 mm and 70 mm long
sides with included angle of 750.Inscribe Ellipse in it.
STEPS ARE SIMILAR TO
THE PREVIOUS CASE
(RECTANGLE METHOD)
ONLY IN PLACE OF RECTANGLE,
HERE IS A PARALLELOGRAM.

4 4

3 3

2 2

1
1

A B

72
PROBLEM 4. ELLIPSE
MAJOR AXIS AB & MINOR AXIS CD ARE
BY ARCS OF CIRCLE METHOD
100 AMD 70MM LONG RESPECTIVELY
.DRAW ELLIPSE BY ARCS OF CIRLES
METHOD. As per the definition Ellipse is locus of point P moving in
a plane such that the SUM of it’s distances from two fixed
STEPS: points (F1 & F2) remains constant and equals to the length
1.Draw both axes as usual.Name the of major axis AB.(Note A .1+ B .1=A . 2 + B. 2 = AB)
ends & intersecting point
2.Taking AO distance I.e.half major
axis, from C, mark F1 & F2 On AB . p4 C
( focus 1 and 2.) p3
3.On line F1- O taking any distance, p2
mark points 1,2,3, & 4
p1
4.Taking F1 center, with distance A-1
draw an arc above AB and taking F2
center, with B-1 distance cut this arc.
Name the point p1 B
5.Repeat this step with same centers but A O
F1 1 2 3 4 F2
taking now A-2 & B-2 distances for
drawing arcs. Name the point p2
6.Similarly get all other P points.
With same steps positions of P can be
located below AB.
7.Join all points by smooth curve to get
an ellipse/
D

73
PROBLEM 5. ELLIPSE
DRAW RHOMBUS OF 100 MM & 70 MM LONG BY RHOMBUS METHOD
DIAGONALS AND INSCRIBE AN ELLIPSE IN IT.

STEPS: 2
1. Draw rhombus of given
dimensions.
2. Mark mid points of all sides &
name Those A,B,C,& D
3. Join these points to the ends of A B
smaller diagonals.
4. Mark points 1,2,3,4 as four
centers.
5. Taking 1 as center and 1-A 3 4
radius draw an arc AB.
6. Take 2 as center draw an arc CD.
7. Similarly taking 3 & 4 as centers
and 3-D radius draw arcs DA & BC.
D C

74
PROBLEM 6:- POINT F IS 50 MM FROM A LINE AB.A POINT P IS MOVING IN A PLANE ELLIPSE
SUCH THAT THE RATIO OF IT’S DISTANCES FROM F AND LINE AB REMAINS CONSTANT
AND EQUALS TO 2/3 DRAW LOCUS OF POINT P. { ECCENTRICITY = 2/3 } DIRECTRIX-FOCUS METHOD

ELLIPSE
A
STEPS:
1 .Draw a vertical line AB and point F
50 mm from it.
2 .Divide 50 mm distance in 5 parts. 45mm
3 .Name 2nd part from F as V. It is 20mm
and 30mm from F and AB line resp.
It is first point giving ratio of it’s
distances from F and AB 2/3 i.e 20/30
4 Form more points giving same ratio such
as 30/45, 40/60, 50/75 etc. (vertex) V
5.Taking 45,60 and 75mm distances from F ( focus)
line AB, draw three vertical lines to the
right side of it.
6. Now with 30, 40 and 50mm distances in
compass cut these lines above and below,
with F as center.
7. Join these points through V in smooth
curve.
This is required locus of P.It is an ELLIPSE.

75
PROBLEM 7: A BALL THROWN IN AIR ATTAINS 100 M HIEGHT
PARABOLA
AND COVERS HORIZONTAL DISTANCE 150 M ON GROUND. RECTANGLE METHOD
Draw the path of the ball (projectile)-

STEPS: 6 6
1.Draw rectangle of above size and
divide it in two equal vertical parts
2.Consider left part for construction. 5 5
Divide height and length in equal
number of parts and name those
1,2,3,4,5& 6 4 4
3.Join vertical 1,2,3,4,5 & 6 to the
top center of rectangle
4.Similarly draw upward vertical
3 3
lines from horizontal1,2,3,4,5
And wherever these lines intersect
previously drawn inclined lines in
sequence Mark those points and 2 2
further join in smooth possible curve.
5.Repeat the construction on right side
rectangle also.Join all in sequence. 1 1
This locus is Parabola.
.

1 2 3 4 5 6 5 4 3 2 1

76
Draw a parabola by tangent method given base 7.5m and axis 4.5m
Take scale 1cm = 0.5m

O
6

5
1’

4.5m
4
2’

3 F 3’

2 4’
4.5m
1
5’

6’
E B 77
A
7.5m
PROBLEM 9: Point F is 50 mm from a vertical straight line AB. PARABOLA
Draw locus of point P, moving in a plane such that DIRECTRIX-FOCUS METHOD
it always remains equidistant from point F and line AB.

PARABOLA
SOLUTION STEPS:
1.Locate center of line, perpendicular to A
AB from point F. This will be initial
point P and also the vertex.
2.Mark 5 mm distance to its right side,
name those points 1,2,3,4 and from P1
those
draw lines parallel to AB.
3.Mark 5 mm distance to its left of P and (VERTEX) V
name it 1.
O 1 2 3 4
F
4.Take O-1 distance as radius and F as
center draw an arc ( focus)
cutting first parallel line to AB. Name
upper point P1 and lower point P2.
P2
(FP1=O1)

5.Similarly repeat this process by taking

again 5mm to right and left and locate
P3P4.
B
6.Join all these points in smooth curve.

It will be the locus of P equidistance

from line AB and fixed point F.
78
Problem No.10: Point P is 40 mm and 30 mm from horizontal HYPERBOLA
and vertical axes respectively.Draw Hyperbola through it. THROUGH A POINT
OF KNOWN CO-ORDINATES
Solution Steps:
1) Extend horizontal
line from P to right side. 2
2) Extend vertical line
from P upward.
3) On horizontal line
from P, mark some points
taking any distance and
name them after P-1,
2,3,4 etc.
4) Join 1-2-3-4 points
to pole O. Let them cut 1
part [P-B] also at 1,2,3,4
points.
5) From horizontal
1,2,3,4 draw vertical 2 1 P 1 2 3
lines downwards and
6) From vertical 1,2,3,4
points [from P-B] draw
1
horizontal lines.
7) Line from 1 40 mm 2
horizontal and line from
1 vertical will meet at 3
P1.Similarly mark P2, P3,
P4 points. O
8) Repeat the procedure
by marking four points 30 mm
on upward vertical line
from P and joining all
those to pole O. Name
this points P6, P7, P8 etc. 79
and join them by smooth
curve.
PROBLEM 12:- POINT F IS 50 MM FROM A LINE AB.A POINT P IS MOVING IN A PLANE HYPERBOLA
SUCH THAT THE RATIO OF IT’S DISTANCES FROM F AND LINE AB REMAINS CONSTANT
AND EQUALS TO 2/3 DRAW LOCUS OF POINT P. { ECCENTRICITY = 2/3 }
DIRECTRIX
FOCUS METHOD

STEPS: A
1 .Draw a vertical line AB and point F
50 mm from it.
2 .Divide 50 mm distance in 5 parts. 30mm
3 .Name 2nd part from F as V. It is 20mm
and 30mm from F and AB line resp.
It is first point giving ratio of it’s
distances from F and AB 2/3 i.e 20/30
4 Form more points giving same ratio such
as 30/45, 40/60, 50/75 etc. (vertex)
V
F ( focus)
5.Taking 45,60 and 75mm distances from
line AB, draw three vertical lines to the
right side of it.
6. Now with 30, 40 and 50mm distances in
compass cut these lines above and below,
with F as center.
7. Join these points through V in smooth
curve.
This is required locus of P.It is an ELLIPSE.

80
 ELLIPSE
Problem 13:
TANGENT & NORMAL
TO DRAW TANGENT & NORMAL
TO THE CURVE FROM A GIVEN POINT ( Q )
1. JOIN POINT Q TO F1 & F2
2. BISECT ANGLE F1Q F2 THE ANGLE BISECTOR IS NORMAL
3. A PERPENDICULAR LINE DRAWN TO IT IS TANGENT TO THE CURVE.

p4 C
p3
p2
p1

A B
O
F1 1 2 3 4 F2

D
81
 ELLIPSE
Problem 14:
TANGENT & NORMAL
TO DRAW TANGENT & NORMAL
TO THE CURVE
ELLIPSE
FROM A GIVEN POINT ( Q ) A

1.JOIN POINT Q TO F. T
2.CONSTRUCT 900 ANGLE WITH
THIS LINE AT POINT F
3.EXTEND THE LINE TO MEET DIRECTRIX
AT T
4. JOIN THIS POINT TO Q AND EXTEND. THIS IS
TANGENT TO ELLIPSE FROM Q (vertex) V
5.TO THIS TANGENT DRAW PERPENDICULAR
F ( focus)
LINE FROM Q. IT IS NORMAL TO CURVE. 900
N

Q
N

82
T
 PARABOLA
Problem 15: TANGENT & NORMAL
TO DRAW TANGENT & NORMAL
TO THE CURVE T PARABOLA
FROM A GIVEN POINT ( Q )
A

1.JOIN POINT Q TO F.
2.CONSTRUCT 900 ANGLE WITH
THIS LINE AT POINT F
3.EXTEND THE LINE TO MEET DIRECTRIX
AT T
4. JOIN THIS POINT TO Q AND EXTEND. THIS IS VERTEX V
TANGENT TO THE CURVE FROM Q 900
F
5.TO THIS TANGENT DRAW PERPENDICULAR ( focus)
LINE FROM Q. IT IS NORMAL TO CURVE.
N

Q
B N

T
83
 PARABOLA
Problem 15: TANGENT & NORMAL
TO DRAW TANGENT & NORMAL
TO THE CURVE T PARABOLA
FROM A GIVEN POINT ( Q )
A

1.JOIN POINT Q TO F.
2.CONSTRUCT 900 ANGLE WITH
THIS LINE AT POINT F
3.EXTEND THE LINE TO MEET DIRECTRIX
AT T
4. JOIN THIS POINT TO Q AND EXTEND. THIS IS VERTEX V
TANGENT TO THE CURVE FROM Q 900
F
5.TO THIS TANGENT DRAW PERPENDICULAR ( focus)
LINE FROM Q. IT IS NORMAL TO CURVE.
N

Q
B N

T
84
 HYPERBOLA
Problem 16
TANGENT & NORMAL
TO DRAW TANGENT & NORMAL
TO THE CURVE
FROM A GIVEN POINT ( Q ) A

1.JOIN POINT Q TO F.
2.CONSTRUCT 900 ANGLE WITH THIS LINE AT
POINT F T
3.EXTEND THE LINE TO MEET DIRECTRIX AT T
4. JOIN THIS POINT TO Q AND EXTEND. THIS IS
TANGENT TO CURVE FROM Q
(vertex)
V
F ( focus)
5.TO THIS TANGENT DRAW PERPENDICULAR 900
LINE FROM Q. IT IS NORMAL TO CURVE.
N

N Q

T 85
 ENGINEERING CURVES
Part-II
(Point undergoing two types of displacements)

INVOLUTE CYCLOID SPIRAL HELIX

1. Involute of a circle 1. General Cycloid 1. Spiral of 1. On Cylinder
a)String Length = D One Convolution.
2. Trochoid 2. On a Cone
b)String Length > D ( superior) 2. Spiral of
3. Trochoid Two Convolutions.
c)String Length < D ( Inferior)
4. Epi-Cycloid
2. Pole having Composite
shape. 5. Hypo-Cycloid

3. Rod Rolling over

a Semicircular Pole. AND Methods of Drawing
Tangents & Normals
To These Curves.

86
 DEFINITIONS
CYCLOID:
IT IS A LOCUS OF A POINT ON THE SUPERIORTROCHOID:
PERIPHERY OF A CIRCLE WHICH IF THE POINT IN THE DEFINATION
ROLLS ON A STRAIGHT LINE PATH. OF CYCLOID IS OUTSIDE THE CIRCLE

INFERIOR TROCHOID.:
INVOLUTE: IF IT IS INSIDE THE CIRCLE
IT IS A LOCUS OF A FREE END OF A STRING
WHEN IT IS WOUND ROUND A CIRCULAR POLE EPI-CYCLOID
IF THE CIRCLE IS ROLLING ON
ANOTHER CIRCLE FROM OUTSIDE
SPIRAL: HYPO-CYCLOID.
IT IS A CURVE GENERATED BY A POINT IF THE CIRCLE IS ROLLING FROM
WHICH REVOLVES AROUND A FIXED POINT INSIDE THE OTHER CIRCLE,
AND AT THE SAME MOVES TOWARDS IT.

HELIX:
IT IS A CURVE GENERATED BY A POINT WHICH
MOVES AROUND THE SURFACE OF A RIGHT CIRCULAR
CYLINDER / CONE AND AT THE SAME TIME ADVANCES IN AXIAL DIRECTION
AT A SPEED BEARING A CONSTANT RATIO TO THE SPPED OF ROTATION. 87
( for problems refer topic Development of surfaces)
 Problem no 17: Draw Involute of a circle. INVOLUTE OF A CIRCLE
String length is equal to the circumference of circle.

Solution Steps:
1) Point or end P of string AP is
exactly D distance away from A.
Means if this string is wound round
the circle, it will completely cover
P2
given circle. B will meet A after
winding.
2) Divide D (AP) distance into 8 P3
number of equal parts. P1
3) Divide circle also into 8 number
of equal parts.
4) Name after A, 1, 2, 3, 4, etc. up
to 8 on D line AP as well as on
circle (in anticlockwise direction).
5) To radius C-1, C-2, C-3 up to C-8
draw tangents (from 1,2,3,4,etc to 4 to p
circle). P4
4
6) Take distance 1 to P in compass 3
and mark it on tangent from point 1 5
on circle (means one division less 2
than distance AP). 6
7) Name this point P1 1
8) Take 2-P distance in compass 7 A 8
and mark it on the tangent from P5 P
point 2. Name it point P2. P8 1 2 3 4 5 6 7 8
9) Similarly take 3 to P, 4 to P, 5 to P7
P up to 7 to P distance in compass P6 D
and mark on respective tangents
and locate P3, P4, P5 up to P8 (i.e.
A) points and join them in smooth
curve it is an INVOLUTE of a given
circle. 88
 INVOLUTE OF A CIRCLE
Problem 18: Draw Involute of a circle.
String length MORE than D
String length is MORE than the circumference of circle.

Solution Steps: P2
In this case string length is more
than  D.
But remember!
Whatever may be the length of P3 P1
string, mark  D distance
horizontal i.e.along the string
and divide it in 8 number of
equal parts, and not any other
distance. Rest all steps are same
as previous INVOLUTE. Draw
the curve completely.

4 to p
P4 4
3
5
2
6
1
P5 7
8
p8 1 P
2 3 4 5 6 7 8
D
P7
165 mm
P6 (more than D)

89
Problem 19: Draw Involute of a circle. INVOLUTE OF A CIRCLE
String length is LESS than the circumference of circle. String length LESS than D

Solution Steps: P2
In this case string length is Less
than  D.
But remember!
Whatever may be the length of P3
P1
string, mark  D distance
horizontal i.e.along the string
and divide it in 8 number of
equal parts, and not any other
distance. Rest all steps are same
as previous INVOLUTE. Draw
the curve completely.
4 to p
P4 4
3
5
2
6
1
P5 7 P
8
P7 1 2 3 4 5 6 7 8
P6
150 mm
(Less than D)

D
90
Problem: Draw involute of an equilateral triangle of 35 mm sides.

35 3X35

91
Problem: Draw involute of a square of 25 mm sides

25 100

92
PROBLEM 22: DRAW LOCUS OF A POINT ON THE PERIPHERY OF A CIRCLE CYCLOID
WHICH ROLLS ON STRAIGHT LINE PATH. Take Circle diameter as 50 mm

p4
4
p3 p5
3 5

C p2 C1 C2 C3 C4 C5 C6 C7 p6 C
8
2 6

p1
1 p7
7
P p8

D

Solution Steps:
1) From center C draw a horizontal line equal to D distance.
2) Divide D distance into 8 number of equal parts and name them C1, C2, C3__ etc.
3) Divide the circle also into 8 number of equal parts and in clock wise direction, after P name 1, 2, 3 up to 8.
4) From all these points on circle draw horizontal lines. (parallel to locus of C)
5) With a fixed distance C-P in compass, C1 as center, mark a point on horizontal line from 1. Name it P.
6) Repeat this procedure from C2, C3, C4 upto C8 as centers. Mark points P2, P3, P4, P5 up to P8 on the
horizontal lines drawn from 2, 3, 4, 5, 6, 7 respectively.
7) Join all these points by curve. It is Cycloid. 93
 PROBLEM 23: DRAW LOCUS OF A POINT , 5 MM AWAY FROM THE PERIPHERY OF A SUPERIOR TROCHOID
CIRCLE WHICH ROLLS ON STRAIGHT LINE PATH. Take Circle diameter as 50 mm

4 p4

p3 p5
3 5

p2 C C1 C C3 C4 C5 C6 C7 C8 p6
2 6 2

p7
1 p1 7
P D p8

Solution Steps:
1) Draw circle of given diameter and draw a horizontal line from it’s center C of length  D and divide it
in 8 number of equal parts and name them C1, C2, C3, up to C8.
2) Draw circle by CP radius, as in this case CP is larger than radius of circle.
3) Now repeat steps as per the previous problem of cycloid, by dividing this new circle into 8 number of
equal parts and drawing lines from all these points parallel to locus of C and taking CP radius wit
94
different positions of C as centers, cut these lines and get different positions of P and join
4) This curve is called Superior Trochoid.
PROBLEM 24: DRAW LOCUS OF A POINT , 5 MM INSIDE THE PERIPHERY OF A
INFERIOR TROCHOID
CIRCLE WHICH ROLLS ON STRAIGHT LINE PATH. Take Circle diameter as 50 mm

p4
4
p p5
3 5
p2 3
C C1 C2 C3 C4 C5 C6 C7p6 C8
2 6
p1 p7
1 7
P p8

D

Solution Steps:
1) Draw circle of given diameter and draw a horizontal line from it’s center C of length  D and divide it
in 8 number of equal parts and name them C1, C2, C3, up to C8.
2) Draw circle by CP radius, as in this case CP is SHORTER than radius of circle.
3) Now repeat steps as per the previous problem of cycloid, by dividing this new circle into 8 number
of equal parts and drawing lines from all these points parallel to locus of C and taking CP radius
with different positions of C as centers, cut these lines and get different positions of P and join
95
those in curvature.
4) This curve is called Inferior Trochoid.
PROBLEM 25: DRAW LOCUS OF A POINT ON THE PERIPHERY OF A CIRCLE
WHICH ROLLS ON A CURVED PATH. Take diameter of rolling Circle 50 mm EPI CYCLOID :
And radius of directing circle i.e. curved path, 75 mm.

Solution Steps:
1) When smaller circle will roll on
larger circle for one revolution it will
cover  D distance on arc and it will
be decided by included arc angle .
2) Calculate  by formula  = (r/R) x
Generating/
3600. Rolling Circle
3) Construct angle  with radius OC 4 5
and draw an arc by taking O as center C2
OC as radius and form sector of angle 3 6
.
4) Divide this sector into 8 number of 7
equal angular parts. And from C 2
onward name them C1, C2, C3 up to
1
C8. r = CP P
5) Divide smaller circle (Generating
circle) also in 8 number of equal parts.
And next to P in clockwise direction Directing Circle
name those 1, 2, 3, up to 8.
6) With O as center, O-1 as radius
draw an arc in the sector. Take O-2, O- = r 3600
R
3, O-4, O-5 up to O-8 distances with
center O, draw all concentric arcs in O
sector. Take fixed distance C-P in
compass, C1 center, cut arc of 1 at P1.
Repeat procedure and locate P2, P3,
P4, P5 unto P8 (as in cycloid) and join
them by smooth curve. This is EPI – 96
CYCLOID.
PROBLEM 26: DRAW LOCUS OF A POINT ON THE PERIPHERY OF A CIRCLE
WHICH ROLLS FROM THE INSIDE OF A CURVED PATH. Take diameter of HYPO CYCLOID
rolling circle 50 mm and radius of directing circle (curved path) 75 mm.

Solution Steps:
1) Smaller circle is rolling
here, inside the larger
circle. It has to rotate
anticlockwise to move P 7
ahead.
2) Same steps should be P1
6
taken as in case of EPI –
CYCLOID. Only change is 1 P2
in numbering direction of
8 number of equal parts
5
on the smaller circle. P3
3) From next to P in 2
anticlockwise direction,
4 P4
name 1,2,3,4,5,6,7,8. 3
4) Further all steps are P5
P8
that of epi – cycloid. This P6 P7
is called
HYPO – CYCLOID.
r
= 3600
R
O

OC = R ( Radius of Directing Circle)

CP = r (Radius of Generating Circle)
97
Problem 27: Draw a spiral of one convolution. Take distance PO 40 mm.
SPIRAL
IMPORTANT APPROACH FOR CONSTRUCTION!
FIND TOTAL ANGULAR AND TOTAL LINEAR DISPLACEMENT
AND DIVIDE BOTH IN TO SAME NUMBER OF EQUAL PARTS.

P2
Solution Steps 3 1
P1
1. With PO radius draw a circle
and divide it in EIGHT parts. P3
Name those 1,2,3,4, etc. up to 8
2 .Similarly divided line PO also in
EIGHT parts and name those
4 P4 O P
1,2,3,-- as shown. 7 6 5 4 3 2 1
3. Take o-1 distance from op line P7
and draw an arc up to O1 radius
P5 P6
vector. Name the point P1
4. Similarly mark points P2, P3, P4
up to P8
And join those in a smooth curve. 5 7
It is a SPIRAL of one convolution.

6 98
Problem 28 SPIRAL
Point P is 80 mm from point O. It starts moving towards O and reaches it in two of
revolutions around.it Draw locus of point P (To draw a Spiral of TWO convolutions).
two convolutions
IMPORTANT APPROACH FOR CONSTRUCTION!
FIND TOTAL ANGULAR AND TOTAL LINEAR DISPLACEMENT
AND DIVIDE BOTH IN TO SAME NUMBER OF EQUAL PARTS.

2,10
P2

3,11 P1 1,9
SOLUTION STEPS: P3

Total angular displacement here

P10
is two revolutions And P9
Total Linear displacement here P11
is distance PO. 16 13 10 8 7 6 5 4 3 2 1 P
Just divide both in same parts i.e. 4,12
P4 P8 8,16
P12
Circle in EIGHT parts. P15

( means total angular displacement P13 P14

in SIXTEEN parts)
Divide PO also in SIXTEEN parts. P7
Rest steps are similar to the previous P5

problem.
P6
5,13 7,15

99
6,14
 HELIX
(UPON A CYLINDER)
PROBLEM: Draw a helix of one convolution, upon a cylinder. P8
Given 80 mm pitch and 50 mm diameter of a cylinder. 8
(The axial advance during one complete revolution is called P7
The pitch of the helix) 7
P6
6
P5
SOLUTION: 5
Draw projections of a cylinder.
Divide circle and axis in to same no. of equal parts. ( 8 ) 4 P4
Name those as shown.
3
Mark initial position of point ‘P’ P3
Mark various positions of P as shown in animation. 2 P2
Join all points by smooth possible curve.
Make upper half dotted, as it is going behind the solid 1 P1
and hence will not be seen from front side.
P
6

7 5

P 4

1 3

2
100
 HELIX
PROBLEM: Draw a helix of one convolution, upon a cone, P8 (UPON A CONE)
diameter of base 70 mm, axis 90 mm and 90 mm pitch.
(The axial advance during one complete revolution is called P7
The pitch of the helix)
P6

P5
SOLUTION:
Draw projections of a cone
Divide circle and axis in to same no. of equal parts. ( 8 ) P4
Name those as shown.
Mark initial position of point ‘P’ P3
Mark various positions of P as shown in animation.
Join all points by smooth possible curve. P2
Make upper half dotted, as it is going behind the solid
and hence will not be seen from front side. P1
X P Y

7 5

P6 P5
P7 P4
P 4
P8

P1 P3
1 3
P2
2
101
STEPS: Involute
DRAW INVOLUTE AS USUAL.
Method of Drawing
MARK POINT Q ON IT AS DIRECTED. Tangent & Normal
JOIN Q TO THE CENTER OF CIRCLE C.
CONSIDERING CQ DIAMETER, DRAW
A SEMICIRCLE AS SHOWN.
INVOLUTE OF A CIRCLE
MARK POINT OF INTERSECTION OF
THIS SEMICIRCLE AND POLE CIRCLE
AND JOIN IT TO Q. Q
THIS WILL BE NORMAL TO INVOLUTE.

DRAW A LINE AT RIGHT ANGLE TO

THIS LINE FROM Q.

IT WILL BE TANGENT TO INVOLUTE.

4
3
5
C 2
6
1
7
8
P
P8 1 2 3 4 5 6 7 8


D
102
STEPS:
DRAW CYCLOID AS USUAL. CYCLOID
MARK POINT Q ON IT AS DIRECTED.
Method of Drawing
WITH CP DISTANCE, FROM Q. CUT THE Tangent & Normal
POINT ON LOCUS OF C AND JOIN IT TO Q.

FROM THIS POINT DROP A PERPENDICULAR

ON GROUND LINE AND NAME IT N

JOIN N WITH Q.THIS WILL BE NORMAL TO

CYCLOID.

DRAW A LINE AT RIGHT ANGLE TO

THIS LINE FROM Q.

IT WILL BE TANGENT TO CYCLOID.

CYCLOID

C C1 C2 C3 C4 C5 C6 C7 C8

P N
D 103
 Spiral.
Method of Drawing
Tangent & Normal
SPIRAL (ONE CONVOLUSION.)
2

P2
3 1 Difference in length of any radius vectors
Q P1 Constant of the Curve =
Angle between the corresponding
radius vector in radian.
P3
OP – OP2 OP – OP2
= =
/2 1.57

4 P4 O P = 3.185 m.m.
7 6 5 4 3 2 1
P7 STEPS:
*DRAW SPIRAL AS USUAL.
P5 P6 DRAW A SMALL CIRCLE OF RADIUS EQUAL TO THE
CONSTANT OF CURVE CALCULATED ABOVE.

* LOCATE POINT Q AS DISCRIBED IN PROBLEM AND

5 7 THROUGH IT DRAW A TANGENTTO THIS SMALLER
CIRCLE.THIS IS A NORMAL TO THE SPIRAL.

*DRAW A LINE AT RIGHT ANGLE

6
*TO THIS LINE FROM Q.
IT WILL BE TANGENT TO CYCLOID.

104
 ISTE Approved
Workshop

Loci of Point

Dr. VIKAS J. PATEL

Associate Professor
Mechanical Engineering Department
C. K. Pithawalla College of Engineering and Technology
[email protected] & [email protected]

105
 LOCUS
It is a path traced out by a point moving in a plane,
in a particular manner, for one cycle of operation.

The cases are classified in THREE categories for easy understanding.

A} Basic Locus Cases.
B} Oscillating Link……
C} Rotating Link………
Basic Locus Cases:
Here some geometrical objects like point, line, circle will be described with there relative
Positions. Then one point will be allowed to move in a plane maintaining specific relation
with above objects. And studying situation carefully you will be asked to draw it’s locus.
Oscillating & Rotating Link:
Here a link oscillating from one end or rotating around it’s center will be described.
Then a point will be allowed to slide along the link in specific manner. And now studying
the situation carefully you will be asked to draw it’s locus.

STUDY TEN CASES GIVEN ON NEXT PAGES 106

107
108
109
110
111
112
Problem No.7: OSCILLATING LINK
A Link OA, 80 mm long oscillates around O,
600 to right side and returns to it’s initial vertical
Position with uniform velocity.Mean while point
P initially on O starts sliding downwards and
reaches end A with uniform velocity.
Draw locus of point P p
O
p1
Solution Steps: 1 p2 p4
Point P- Reaches End A (Downwards) p3
1) Divide OA in EIGHT equal parts and from O to A after O 2
name 1, 2, 3, 4 up to 8. (i.e. up to point A).
2) Divide 600 angle into four parts (150 each) and mark each
point by A1, A2, A3, A4 and for return A5, A6, A7 andA8.
3
p5 A4
(Initial A point).
3) Take center O, distance in compass O-1 draw an arc upto 4
OA1. Name this point as P1.
1) Similarly O center O-2 distance mark P2 on line O-A2. 5 p6
2) This way locate P3, P4, P5, P6, P7 and P8 and join them. A3
( It will be thw desired locus of P ) A5
6

7 p7 A2
A6
A8 A1
p8
A7
A8

113
 OSCILLATING LINK

Problem No 8:
A Link OA, 80 mm long oscillates around O,
600 to right side, 1200 to left and returns to it’s initial
vertical Position with uniform velocity.Mean while point
P initially on O starts sliding downwards, reaches end A
and returns to O again with uniform velocity.
Draw locus of point P Op
16

15
p1 p4
1 p2
Solution Steps: 14 p3
( P reaches A i.e. moving downwards. 2
& returns to O again i.e.moves upwards ) 13
1.Here distance traveled by point P is PA.plus A 3 p
AP.Hence divide it into eight equal parts.( so
12
12 A4
5
total linear displacement gets divided in 16 4
parts) Name those as shown. 11
2.Link OA goes 600 to right, comes back to A 5 p6
A13 11 A3
original (Vertical) position, goes 600 to left A5
10
and returns to original vertical position. Hence 6
total angular displacement is 2400. A10 p7 A2
Divide this also in 16 parts. (150 each.) 9 7
A14 A6
Name as per previous problem.(A, A1 A2 etc) A9 8 A1
3.Mark different positions of P as per the A15 A p8
procedure adopted in previous case. A7
and complete the problem.
A8
A16

114
 ROTATING LINK
Problem 9:
Rod AB, 100 mm long, revolves in clockwise direction for one revolution.
Meanwhile point P, initially on A starts moving towards B and reaches B.
Draw locus of point P. A2
1) AB Rod revolves around
center O for one revolution and
point P slides along AB rod and A1
reaches end B in one A3
revolution. p1
2) Divide circle in 8 number of p2 p6
p7
equal parts and name in arrow
direction after A-A1, A2, A3, up
to A8.
3) Distance traveled by point P
is AB mm. Divide this also into 8 p5
number of equal parts. p3
p8
4) Initially P is on end A. When
A moves to A1, point P goes A B A4
P 1 4 5 6 7
one linear division (part) away 2 3 p4
from A1. Mark it from A1 and
name the point P1.
5) When A moves to A2, P will
be two parts away from A2
(Name it P2 ). Mark it as above
from A2.
6) From A3 mark P3 three
parts away from P3.
7) Similarly locate P4, P5, P6, A7
A5
P7 and P8 which will be eight
parts away from A8. [Means P
has reached B].
8) Join all P points by smooth A6 115
curve. It will be locus of P
 Problem 10 : ROTATING LINK
Rod AB, 100 mm long, revolves in clockwise direction for one revolution.
Meanwhile point P, initially on A starts moving towards B, reaches B
And returns to A in one revolution of rod.
Draw locus of point P. A2

Solution Steps
1) AB Rod revolves around center O
A1
A3
for one revolution and point P slides
along rod AB reaches end B and
returns to A.
2) Divide circle in 8 number of equal p5
p1
parts and name in arrow direction
after A-A1, A2, A3, up to A8.
3) Distance traveled by point P is AB
plus AB mm. Divide AB in 4 parts so
those will be 8 equal parts on return. p4
4) Initially P is on end A. When A p2 A4
A
moves to A1, point P goes one P 1+7 2+6 p +3 5 4 +B
linear division (part) away from A1. p8 6
Mark it from A1 and name the point
P1.
5) When A moves to A2, P will be
two parts away from A2 (Name it P2
). Mark it as above from A2. p7 p3
6) From A3 mark P3 three parts
away from P3.
7) Similarly locate P4, P5, P6, P7 A7
and P8 which will be eight parts away A5
from A8. [Means P has reached B].
8) Join all P points by smooth curve.
It will be locus of P
The Locus will follow the loop A6 116
path two times in one revolution.
ORTHOGRAPHIC PROJECTIONS

117
 DRAWINGS:
( A Graphical Representation)

The Fact about:

If compared with Verbal or Written Description,
Drawings offer far better idea about the Shape, Size & Appearance of
any object or situation or location, that too in quite a less time.

Hence it has become the Best Media of Communication

not only in Engineering but in almost all Fields.

118
 Drawings
(Some Types)

Portraits
Botanical Drawings ( human faces,
Nature Drawings ( plants, flowers etc.) expressions etc.)
( landscape, Geographical
scenery etc.) Zoological Drawings
Drawings Engineering Drawings,
(creatures, animals etc.)
( maps etc.) (projections.)

Building Related Drawings. Machine component Drawings

Orthographic Projections Isometric ( Mech.Engg.Term.)

(Fv,Tv & Sv.-Mech.Engg terms) or Perspective(Civil Engg.Term)
(Plan, Elevation- Civil Engg.terms)
(Working Drawings 2-D type) (Actual Object Drawing 3-D)

119
 ORTHOGRAPHIC PROJECTIONS:
IT IS A TECHNICAL DRAWING IN WHICH DIFFERENT VIEWS OF AN OBJECT
ARE PROJECTED ON DIFFERENT REFERENCE PLANES
OBSERVING PERPENDICULAR TO RESPECTIVE REFERENCE PLANE
Different Reference planes are
Horizontal Plane (HP),
Vertical Frontal Plane ( VP )
Side Or Profile Plane ( PP)
And
Different Views are Front View (FV), Top View (TV) and Side View (SV)
FV is a view projected on VP.
TV is a view projected on HP.
SV is a view projected on PP.
IMPORTANT TERMS OF ORTHOGRAPHIC PROJECTIONS:
1 Planes.
2 Pattern of planes & Pattern of views
3 Methods of drawing Orthographic Projections
120
 PLANES
1
PRINCIPAL PLANES
HP AND VP

AUXILIARY PLANES

Auxiliary Vertical Plane Auxiliary Inclined Plane Profile Plane

(A.V.P.) (A.I.P.) ( P.P.)

A.V.P.
⊥ to Hp &  to Vp

121
 PATTERN OF PLANES & VIEWS (First Angle Method)
2
THIS IS A PICTORIAL SET-UP OF ALL THREE PLANES.
ARROW DIRECTION IS A NORMAL WAY OF OBSERVING THE OBJECT.
BUT IN THIS DIRECTION ONLY VP AND A VIEW ON IT (FV) CAN BE SEEN.
THE OTHER PLANES AND VIEWS ON THOSE CAN NOT BE SEEN.

PROCEDURE TO SOLVE ABOVE PROBLEM:-

TO MAKE THOSE PLANES ALSO VISIBLE FROM THE ARROW DIRECTION,
A) HP IS ROTATED 900 DOUNWARD
B) PP, 900 IN RIGHT SIDE DIRECTION.
THIS WAY BOTH PLANES ARE BROUGHT IN THE SAME PLANE CONTAINING VP.

Click to view Animation On clicking the button if a warning comes please click YES to continue, this program is
safe for your pc.

VP PP
Y
FV LSV

X Y
X TV

HP

ACTUAL PATTERN OF PLANES & VIEWS

HP IS ROTATED DOWNWARD 900 PP IS ROTATED IN RIGHT SIDE 900 OF ORTHOGRAPHIC PROJECTIONS
122
AND AND DRAWN IN
BROUGHT IN THE PLANE OF VP. BROUGHT IN THE PLANE OF VP. FIRST ANGLE METHOD OF PROJECTIONS
 3 Methods of Drawing Orthographic Projections

First Angle Projections Method Third Angle Projections Method

Here views are drawn Here views are drawn
by placing object by placing object
in 1st Quadrant in 3rd Quadrant.
( Fv above X-y, Tv below X-y ) SYMBOLIC ( Tv above X-y, Fv below X-y )
PRESENTATION
OF BOTH METHODS
WITH AN OBJECT
STANDING ON HP ( GROUND) TV
FV ON IT’S BASE.
X Y NOTE:- X Y
HP term is used in1st Angle method
& FV
TV
For the same
G L
Ground term is used 123
in 3rd Angle method of projections
 FIRST ANGLE
FOR T.V.
PROJECTION
IN THIS METHOD,
THE OBJECT IS ASSUMED TO BE
SITUATED IN FIRST QUADRANT
MEANS
ABOVE HP & INFRONT OF VP.

OBJECT IS INBETWEEN
OBSERVER & PLANE.

VP PP

FV LSV

X Y
TV

HP

ACTUAL PATTERN OF
PLANES & VIEWS
IN
FIRST ANGLE METHOD 124
OF PROJECTIONS
 THIRD ANGLE FOR T.V.
PROJECTION
IN THIS METHOD,
THE OBJECT IS ASSUMED TO BE
SITUATED IN THIRD QUADRANT
( BELOW HP & BEHIND OF VP. )

PLANES BEING TRANSPERENT

AND INBETWEEN
OBSERVER & OBJECT.

TV
X Y
LSV FV

ACTUAL PATTERN OF
PLANES & VIEWS
OF
THIRD ANGLE PROJECTIONS

125
 ORTHOGRAPHIC PROJECTIONS
{ MACHINE ELEMENTS }
OBJECT IS OBSERVED IN THREE DIRECTIONS.
THE DIRECTIONS SHOULD BE NORMAL
TO THE RESPECTIVE PLANES.
AND NOW PROJECT THREE DIFFERENT VIEWS ON THOSE PLANES.
THESE VEWS ARE FRONT VIEW , TOP VIEW AND SIDE VIEW.

FRONT VIEW IS A VIEW PROJECTED ON VERTICAL PLANE ( VP )

TOP VIEW IS A VIEW PROJECTED ON HORIZONTAL PLANE ( HP )
SIDE VIEW IS A VIEW PROJECTED ON PROFILE PLANE ( PP )

FIRST STUDY THE CONCEPT OF 1ST AND 3RD ANGLE

PROJECTION METHODS

AND THEN STUDY NEXT 26 ILLUSTRATED CASES CAREFULLY.

TRY TO RECOGNIZE SURFACES
PERPENDICULAR TO THE ARROW DIRECTIONS 126
 FIRST ANGLE
FOR T.V.
PROJECTION
IN THIS METHOD,
THE OBJECT IS ASSUMED TO BE
SITUATED IN FIRST QUADRANT
MEANS
ABOVE HP & INFRONT OF VP.

OBJECT IS INBETWEEN
OBSERVER & PLANE.

VP PP

FV LSV

X Y
TV

HP

ACTUAL PATTERN OF
PLANES & VIEWS
IN
FIRST ANGLE METHOD 127
OF PROJECTIONS
 FOR T.V.
THIRD ANGLE
PROJECTION
IN THIS METHOD,
THE OBJECT IS ASSUMED TO BE
SITUATED IN THIRD QUADRANT
( BELOW HP & BEHIND OF VP. )

PLANES BEING TRANSPERENT

AND INBETWEEN
OBSERVER & OBJECT.

TV
X Y
LSV FV

ACTUAL PATTERN OF
PLANES & VIEWS
OF
THIRD ANGLE PROJECTIONS

128
 FOR T.V.
1

ORTHOGRAPHIC PROJECTIONS

FRONT VIEW L.H.SIDE VIEW

x y

PICTORIAL PRESENTATION IS GIVEN TOP VIEW

DRAW THREE VIEWS OF THIS OBJECT
BY FIRST ANGLE PROJECTION METHOD 129
 FOR T.V.
2

ORTHOGRAPHIC PROJECTIONS

FRONT VIEW L.H.SIDE VIEW

X Y

TOP VIEW

PICTORIAL PRESENTATION IS GIVEN

DRAW THREE VIEWS OF THIS OBJECT
130
BY FIRST ANGLE PROJECTION METHOD
 FOR T.V.
3

ORTHOGRAPHIC PROJECTIONS

FRONT VIEW L.H.SIDE VIEW

X Y

TOP VIEW

PICTORIAL PRESENTATION IS GIVEN

DRAW THREE VIEWS OF THIS OBJECT
BY FIRST ANGLE PROJECTION METHOD 131
 4
FOR T.V.

ORTHOGRAPHIC PROJECTIONS

FRONT VIEW L.H.SIDE VIEW

X Y

TOP VIEW

PICTORIAL PRESENTATION IS GIVEN

DRAW THREE VIEWS OF THIS OBJECT
132
BY FIRST ANGLE PROJECTION METHOD
 FOR T.V.
5

ORTHOGRAPHIC PROJECTIONS

FRONT VIEW L.H.SIDE VIEW

X Y

PICTORIAL PRESENTATION IS GIVEN

TOP VIEW

DRAW THREE VIEWS OF THIS OBJECT

BY FIRST ANGLE PROJECTION METHOD 133
 6
FOR T.V.

ORTHOGRAPHIC PROJECTIONS

FRONT VIEW L.H.SIDE VIEW

X Y

TOP VIEW

PICTORIAL PRESENTATION IS GIVEN

DRAW THREE VIEWS OF THIS OBJECT
BY FIRST ANGLE PROJECTION METHOD 134
 7
FOR T.V.

ORTHOGRAPHIC PROJECTIONS

FRONT VIEW L.H.SIDE VIEW

X Y

PICTORIAL PRESENTATION IS GIVEN TOP VIEW

DRAW THREE VIEWS OF THIS OBJECT

135
BY FIRST ANGLE PROJECTION METHOD
 8
FOR T.V.
ORTHOGRAPHIC PROJECTIONS

FRONT VIEW

50

X Y

20

25

25 20

TOP VIEW

PICTORIAL PRESENTATION IS GIVEN

DRAW THREE VIEWS OF THIS OBJECT
BY FIRST ANGLE PROJECTION METHOD 136
 9
FOR T.V.
ORTHOGRAPHIC PROJECTIONS

FRONT VIEW L.H.SIDE VIEW

X Y

TOP VIEW
PICTORIAL PRESENTATION IS GIVEN
DRAW THREE VIEWS OF THIS OBJECT
BY FIRST ANGLE PROJECTION METHOD 137
 10
FOR T.V. ORTHOGRAPHIC PROJECTIONS

FRONT VIEW L.H.SIDE VIEW

X Y

PICTORIAL PRESENTATION IS GIVEN TOP VIEW

DRAW THREE VIEWS OF THIS OBJECT

BY FIRST ANGLE PROJECTION METHOD

138
 FOR T.V. 11
ORTHOGRAPHIC PROJECTIONS

FRONT VIEW L.H.SIDE VIEW

X Y

TOP VIEW
PICTORIAL PRESENTATION IS GIVEN
DRAW THREE VIEWS OF THIS OBJECT
BY FIRST ANGLE PROJECTION METHOD 139
 12
FOR T.V.

ORTHOGRAPHIC PROJECTIONS

FRONT VIEW L.H.SIDE VIEW

X Y

PICTORIAL PRESENTATION IS GIVEN TOP VIEW

DRAW THREE VIEWS OF THIS OBJECT

BY FIRST ANGLE PROJECTION METHOD
140
 13
FOR T.V.
ORTHOGRAPHIC PROJECTIONS

35
FV

35

10
x y

10 20 30

40

70

TV
O
PICTORIAL PRESENTATION IS GIVEN
DRAW FV AND TV OF THIS OBJECT 141
BY FIRST ANGLE PROJECTION METHOD
 14

FOR T.V. ORTHOGRAPHIC PROJECTIONS

FV

30 10 30 SV

30

10

30
x y

ALL VIEWS IDENTICAL

TV
PICTORIAL PRESENTATION IS GIVEN
DRAW THREE VIEWS OF THIS OBJECT
BY FIRST ANGLE PROJECTION METHOD 142
 15

ORTHOGRAPHIC PROJECTIONS
FOR T.V.
ALL VIEWS IDENTICAL

FV SV

x y

10
40 60

40
TV
60
PICTORIAL PRESENTATION IS GIVEN
DRAW THREE VIEWS OF THIS OBJECT
BY FIRST ANGLE PROJECTION METHOD 143
 FOR T.V.
ORTHOGRAPHIC PROJECTIONS 16
ALL VIEWS IDENTICAL

FV SV

x y
10

40 60

PICTORIAL PRESENTATION IS GIVEN TOP VIEW

40
DRAW THREE VIEWS OF THIS OBJECT
BY FIRST ANGLE PROJECTION METHOD 60
144
 17

ORTHOGRAPHIC PROJECTIONS

FRONT VIEW L.H.SIDE VIEW

30 SQUARE
40 20

50

20
10
X Y
30
O 60
F.V.
S.V.
PICTORIAL PRESENTATION IS GIVEN
DRAW FV AND SV OF THIS OBJECT
BY FIRST ANGLE PROJECTION METHOD

145
 FOR T.V.
ORTHOGRAPHIC PROJECTIONS 18

FV
40

X 10 Y
O
30 D 45

O
10
50
PICTORIAL PRESENTATION IS GIVEN
DRAW FV AND TV OF THIS OBJECT
BY FIRST ANGLE PROJECTION METHOD
80

TV
146
 19
FOR T.V.

ORTHOGRAPHIC PROJECTIONS

FV 40

X O 10 Y
100
10
25
TV
10 30 10
25
30 R O
20 D
PICTORIAL PRESENTATION IS GIVEN
DRAW FV AND TV OF THIS OBJECT
BY FIRST ANGLE PROJECTION METHOD

147
PICTORIAL PRESENTATION IS GIVEN ORTHOGRAPHIC PROJECTIONS 20
DRAW FV AND TV OF THIS OBJECT
BY FIRST ANGLE PROJECTION METHOD
30
FOR T.V.
FV
RECT.
SLOT

10 50
35

10
X Y

20 D

TV

60 D
30 D

TOP VIEW
148

O
 21

ORTHOGRAPHIC PROJECTIONS
10

25 15

25
40 10

25

25

O O
80 25

F.V. S.V.

PICTORIAL PRESENTATION IS GIVEN

DRAW FV AND SV OF THIS OBJECT
BY FIRST ANGLE PROJECTION METHOD 149
 FOR T.V.
22
ORTHOGRAPHIC PROJECTIONS

450

30
FV

40

X Y

30 D

40 TV

O
PICTORIAL PRESENTATION IS GIVEN
15
DRAW FV AND TV OF THIS OBJECT 40
BY FIRST ANGLE PROJECTION METHOD 150
 23

ORTHOGRAPHIC PROJECTIONS

HEX PART
30
20
20
40
20

O 50
20
15

O 30
100 60
PICTORIAL PRESENTATION IS GIVEN FRONT VIEW L.H.SIDE VIEW
DRAW FV ABD SV OF THIS OBJECT 151
BY FIRST ANGLE PROJECTION METHOD
 FOR T.V.
ORTHOGRAPHIC PROJECTIONS 24

20 40

FRONT VIEW

F.V.
30

10
X Y
O

10

30

10

30
O 80
PICTORIAL PRESENTATION IS GIVEN T.V. TOP VIEW
DRAW FV AND TV OF THIS OBJECT 152
BY FIRST ANGLE PROJECTION METHOD
 25

ORTHOGRAPHIC PROJECTIONS

10 10 15

25

25
X Y
O 50 10

FV LSV

PICTORIAL PRESENTATION IS GIVEN

DRAW FV AND LSV OF THIS OBJECT
BY FIRST ANGLE PROJECTION METHOD

153
 PICTORIAL PRESENTATION IS GIVEN
26 DRAW FV AND SV OF THIS OBJECT
BY FIRST ANGLE PROJECTION METHOD

ORTHOGRAPHIC PROJECTIONS

30 20 10 20

15
10

15

O
15
30

15
X Y
50
F.V. LEFT S.V. 154
PROJECTION O POINT & LINE

155
 ORTHOGRAPHIC PROJECTIONS
OF POINTS, LINES, PLANES, AND SOLIDS.

TO DRAW PROJECTIONS OF ANY OBJECT,

ONE MUST HAVE FOLLOWING INFORMATION
A) OBJECT
{ WITH IT’S DESCRIPTION, WELL DEFINED.}
B) OBSERVER
{ ALWAYS OBSERVING PERPENDICULAR TO RESP. REF.PLANE}.
C) LOCATION OF OBJECT,
{ MEANS IT’S POSITION WITH REFFERENCE TO H.P. & V.P.}

TERMS ‘ABOVE’ & ‘BELOW’ WITH RESPECTIVE TO H.P.

AND TERMS ‘INFRONT’ & ‘BEHIND’ WITH RESPECTIVE TO V.P
FORM 4 QUADRANTS.
OBJECTS CAN BE PLACED IN ANY ONE OF THESE 4 QUADRANTS.

IT IS INTERESTING TO LEARN THE EFFECT ON THE POSITIONS OF VIEWS ( FV, TV )

OF THE OBJECT WITH RESP. TO X-Y LINE, WHEN PLACED IN DIFFERENT QUADRANTS.

. 156
 NOTATIONS

FOLLOWING NOTATIONS SHOULD BE FOLLOWED WHILE NAMEING

DIFFERENT VIEWS IN ORTHOGRAPHIC PROJECTIONS.

OBJECT POINT A LINE AB

IT’S TOP VIEW a ab

IT’S FRONT VIEW a’ a’ b’

IT’S SIDE VIEW a” a” b”

SAME SYSTEM OF NOTATIONS SHOULD BE FOLLOWED

INCASE NUMBERS, LIKE 1, 2, 3 – ARE USED.

157
 VP
2nd Quad. 1ST Quad.

Y
Observer

X Y HP
X

3rd Quad. 4th Quad.

THIS QUADRANT PATTERN,

IF OBSERVED ALONG X-Y LINE ( IN RED ARROW DIRECTION)
WILL EXACTLY APPEAR AS SHOWN ON RIGHT SIDE AND HENCE,
158
IT IS FURTHER USED TO UNDERSTAND ILLUSTRATION PROPERLLY.
 Point A is POINT A IN VP POINT A IN
Placed In ND
2 QUADRANT 1ST QUADRANT
VP a’
different A A
quadrants a’
and it’s Fv & Tv a
are brought in
same plane for HP OBSERVER

Observer to see
clearly. HP OBSERVER
Fv is visible as
it is a view on
VP. But as Tv is a
is a view on Hp,
it is rotated
downward 900,
In clockwise
direction.The
In front part of a
Hp comes below
xy line and the
part behind Vp HP
comes above. HP OBSERVER
OBSERVER

Observe and
note the a
process. a’
A a’
POINT A IN A POINT A IN
3RD QUADRANT VP 4TH QUADRANT
VP

159
 PROJECTIONS OF A POINT IN FIRST QUADRANT.
POINT A ABOVE HP POINT A ABOVE HP POINT A IN HP
& INFRONT OF VP & IN VP & INFRONT OF VP
For Tv
For Tv

PICTORIAL PICTORIAL For Tv

PRESENTATION A PRESENTATION
a’ a’
A Y
Y
Y a’
a
a
X a X X A

ORTHOGRAPHIC PRESENTATIONS
OF ALL ABOVE CASES.

Fv above xy, Fv above xy, Fv on xy,

Tv below xy. Tv on xy. Tv below xy.
VP VP VP

a’ a’

X Y X Y X
a’ Y
a

a a

HP HP HP 160
 PROJECTIONS OF STRAIGHT LINES.
INFORMATION REGARDING A LINE means
IT’S LENGTH,
POSITION OF IT’S ENDS WITH HP & VP
IT’S INCLINATIONS WITH HP & VP WILL BE GIVEN.
AIM:- TO DRAW IT’S PROJECTIONS - MEANS FV & TV.

SIMPLE CASES OF THE LINE

1. A VERTICAL LINE ( LINE PERPENDICULAR TO HP & // TO VP)

2. LINE PARALLEL TO BOTH HP & VP.

3. LINE INCLINED TO HP & PARALLEL TO VP.

4. LINE INCLINED TO VP & PARALLEL TO HP.

5. LINE INCLINED TO BOTH HP & VP.

STUDY ILLUSTRATIONS GIVEN ON NEXT PAGE

SHOWING CLEARLY THE NATURE OF FV & TV
OF LINES LISTED ABOVE AND NOTE RESULTS.
161
 For Tv Orthographic Pattern
(Pictorial Presentation) V.P.
a’
Note: a’
Fv is a vertical line
A Showing True Length Fv
1.
FV &
Tv is a point. b’
A Line b’
perpendicular Y
X Y
to Hp B

& TV a b
Tv a b
// to Vp X

H.P.
Orthographic Pattern
(Pictorial Presentation) For Tv Note: V.P.
Fv & Tv both are
2. // to xy a’ Fv b’
b’ &
A Line B both show T. L.
// to Hp a’
& A Y X Y
// to Vp
b a b
Tv
X
a
H.P. 162
 Fv inclined to xy V.P.
Tv parallel to xy. b’
3. b’

A Line inclined to Hp B
a’ 
and  Y
parallel to Vp a’ X Y

(Pictorial presentation) A b
a
T.V. b
X
a
H.P.
Orthographic Projections

Tv inclined to xy V.P.
4. Fv parallel to xy.
a’ Fv b’
A Line inclined to Vp b’

and a’
parallel to Hp A
Ø
B X Y
(Pictorial presentation) a Ø

Ø Tv
a b
b
H.P. 163
 For Tv
For Tv
5. A Line inclined to both
Hp and Vp b’
b’
(Pictorial presentation)
B
B

 Y
Y
On removal of object a’
a’ i.e. Line AB
Fv as a image on Vp.
A
A Tv as a image on Hp,

 X
X a T.V. b
a T.V. b
V.P.
b’
FV
a’ 

X Y
Orthographic Projections Note These Facts:-
Fv is seen on Vp clearly. Both Fv & Tv are inclined to xy.
To see Tv clearly, HP is a  (No view is parallel to xy)
rotated 900 downwards, Both Fv & Tv are reduced lengths.
Hence it comes below xy. TV (No view shows True Length)

H.P. b 164
 Orthographic Projections Note the procedure Note the procedure
Means Fv & Tv of Line AB When Fv & Tv known, When True Length is known,
are shown below, How to find True Length. How to locate Fv & Tv.
(Views are rotated to determine (Component a-1 of TL is drawn
with their apparent Inclinations
True Length & it’s inclinations which is further rotated
&
with Hp & Vp). to determine Fv)
V.P. V.P. V.P.
b’ b’ b1’ b’ b1’

FV FV
TL 
a’  a’  a’  1’

X Y X Y X Y

1
a  b2 a
a  TV
Ø


TV TV

H.P. b H.P. b H.P. b b1

Here TV (ab) is not // to XY line In this sketch, TV is rotated Here a -1 is component

Hence it’s corresponding FV and made // to XY line. of TL ab1 gives length of Fv.
a’ b’ is not showing Hence it’s corresponding Hence it is brought Up to
True Length & FV a’ b1’ Is showing Locus of a’ and further rotated
True Length to get point b’. a’ b’ will be Fv.
True Inclination with Hp.
& Similarly drawing component
165
of other TL(a’ b1‘) Tv can be drawn.
True Inclination with Hp.
The most important diagram showing graphical relations 1) True Length ( TL) – a’ b1’ & a b
among all important parameters of this topic. 2) Angle of TL with Hp -  Important
TEN parameters
Study and memorize it as a CIRCUIT DIAGRAM 3) Angle of TL with Vp – Ø to be remembered
And use in solving various problems.
4) Angle of FV with xy –  with Notations

V.P. 5) Angle of TV with xy –  used here onward

Distance between
End Projectors. 6) LTV (length of FV) – Component (a-1)
b’ b1’
7) LFV (length of TV) – Component (a’-1’)
8) Position of A- Distances of a & a’ from xy
9) Position of B- Distances of b & b’ from xy
 10) Distance between End Projectors
 1’
a’
LTV
NOTE this
X Y &  Construct with a’
a LFV 1 Ø&  Construct with a
Ø
b’ & b1’ on same locus.

b & b1 on same locus.

Also Remember
b b1
H.P. True Length is never rotated. It’s horizontal component
is drawn & it is further rotated to locate view.

Views are always rotated, made horizontal & further

extended to locate TL,  & Ø 166
 GROUP (A)
GENERAL CASES OF THE LINE INCLINED TO BOTH HP & VP
PROBLEM 1) ( based on 10 parameters).
Line AB is 75 mm long and it is 300 &
400 Inclined to Hp & Vp respectively.
End A is 12mm above Hp and 10 mm b’ b’1
in front of Vp.
Draw projections. Line is in 1st quadrant.
FV
SOLUTION STEPS: TL
1) Draw xy line and one projector.
2) Locate a’ 12mm above xy line
& a 10mm below xy line. 
3) Take 300 angle from a’ & 400 from
a and mark TL I.e. 75mm on both
a’
lines. Name those points b1’ and b1 X Y
respectively.
4) Join both points with a’ and a resp. a LFV
5) Draw horizontal lines (Locus) from Ø 1
both points.
6) Draw horizontal component of TL
a b1 from point b1 and name it 1.
( the length a-1 gives length of Fv
as we have seen already.) TV TL
7) Extend it up to locus of a’ and
rotating a’ as center locate b’ as
shown. Join a’ b’ as Fv.
8) From b’ drop a projector down
ward & get point b. Join a & b
b b1
167
I.e. Tv.
PROBLEM 2:
Line AB 75mm long makes 450 inclination with Vp while it’s Fv makes 550.
End A is 10 mm above Hp and 15 mm in front of Vp.If line is in 1st quadrant
draw it’s projections and find it’s inclination with Hp.
b’ b’1 LOCUS OF
Solution Steps:-
1.Draw x-y line.
2.Draw one projector for a’ & a
3.Locate a’ 10mm above x-y &
Tv a 15 mm below xy.
4.Draw a line 450 inclined to xy 550
from point a and cut TL 75 mm
on it and name that point b1
Draw locus from point b1
a’
5.Take 550 angle from a’ for Fv
above xy line. X y
6.Draw a vertical line from b1
up to locus of a and name it 1.
It is horizontal component of a LFV
TL & is LFV.
1
7.Continue it to locus of a’ and
rotate upward up to the line
of Fv and name it b’.This a’ b’
line is Fv.
8. Drop a projector from b’ on
locus from point b1 and
name intersecting point b.
Line a b is Tv of line AB.
9.Draw locus from b’ and from
a’ with TL distance cut point b1‘
10.Join a’ b1’ as TL and measure
it’s angle at a’. LOCUS OF b
b 168
It will be true angle of line with HP. b1
 PROBLEM 3:
Fv of line AB is 500 inclined to xy and measures 55
mm long while it’s Tv is 600 inclined to xy line. If
end A is 10 mm above Hp and 15 mm in front of
Vp, draw it’s projections,find TL, inclinations of line
with Hp & Vp. b’ b’1

SOLUTION STEPS:
1.Draw xy line and one projector.
2.Locate a’ 10 mm above xy and
a 15 mm below xy line.
3.Draw locus from these points. 500
4.Draw Fv 500 to xy from a’ and 
mark b’ Cutting 55mm on it. a’
X
5.Similarly draw Tv 600 to xy
from a & drawing projector from b’
y
Locate point b and join a b.
6.Then rotating views as shown, a

locate True Lengths ab1 & a’b1’ 600
and their angles with Hp and Vp.

b1 169
b
 PROBLEM 4 :-
Line AB is 75 mm long .It’s Fv and Tv measure 50 mm & 60 mm long respectively.
End A is 10 mm above Hp and 15 mm in front of Vp. Draw projections of line AB
if end B is in first quadrant.Find angle with Hp and Vp.
b’ b’1

SOLUTION STEPS:
1.Draw xy line and one projector.
2.Locate a’ 10 mm above xy and
a 15 mm below xy line.
3.Draw locus from these points.
4.Cut 60mm distance on locus of a’  LTV 1’
& mark 1’ on it as it is LTV. a’
5.Similarly Similarly cut 50mm on X Y
locus of a and mark point 1 as it is LFV.
6.From 1’ draw a vertical line upward
a LFV
and from a’ taking TL ( 75mm ) in 1

compass, mark b’1 point on it.
Join a’ b’1 points.
7. Draw locus from b’1
8. With same steps below get b1 point
and draw also locus from it.
9. Now rotating one of the components
I.e. a-1 locate b’ and join a’ with it
to get Fv.
10. Locate tv similarly and measure
Angles  & 
b1 170
b
 PROBLEM 5 :-
T.V. of a 75 mm long Line CD, measures 50 mm.
End C is in Hp and 50 mm in front of Vp.
End D is 15 mm in front of Vp and it is above Hp.
Draw projections of CD and find angles with Hp and Vp. d’ d’1 LOCUS OF d’ & d’1

SOLUTION STEPS:
1.Draw xy line and one projector.
2.Locate c’ on xy and
c 50mm below xy line.
3.Draw locus from these points.
4.Draw locus of d 15 mm below xy
5.Cut 50mm & 75 mm distances on c’ 
locus of d from c and mark points X Y
d & d1 as these are Tv and line CD d d1 LOCUS OF d & d1
lengths resp.& join both with c.
6.From d1 draw a vertical line upward
up to xy I.e. up to locus of c’ and
draw an arc as shown.
7 Then draw one projector from d to
meet this arc in d’ point & join c’ d’
8. Draw locus of d’ and cut 75 mm
on it from c’ as TL
9.Measure Angles  &  c 

171
 GROUP (B)
PROBLEMS INVOLVING TRACES OF THE LINE.

TRACES OF THE LINE:-

THESE ARE THE POINTS OF INTERSECTIONS OF A LINE ( OR IT’S EXTENSION )

WITH RESPECTIVE REFFERENCE PLANES.

A LINE ITSELF OR IT’S EXTENSION, WHERE EVER TOUCHES H.P.,

THAT POINT IS CALLED TRACE OF THE LINE ON H.P.( IT IS CALLED H.T.)

SIMILARLY, A LINE ITSELF OR IT’S EXTENSION, WHERE EVER TOUCHES V.P.,

THAT POINT IS CALLED TRACE OF THE LINE ON V.P.( IT IS CALLED V.T.)

V.T.:- It is a point on Vp.

Hence it is called Fv of a point in Vp.
Hence it’s Tv comes on XY line.( Here onward named as v )
H.T.:- It is a point on Hp.
Hence it is called Tv of a point in Hp.
Hence it’s Fv comes on XY line.( Here onward named as ’h’ )
172
 b’

STEPS TO LOCATE HT.

(WHEN PROJECTIONS ARE GIVEN.)
1. Begin with FV. Extend FV up to XY line. a’
2. Name this point h’ v h’
( as it is a Fv of a point in Hp) x y
3. Draw one projector from h’.
4. Now extend Tv to meet this projector. VT’ HT
This point is HT a

STEPS TO LOCATE VT.

Observe & note :-
(WHEN PROJECTIONS ARE GIVEN.) 1. Points h’ & v always on x-y line. b

1. Begin with TV. Extend TV up to XY line. 2. VT’ & v always on one projector.
2. Name this point v
3. HT & h’ always on one projector.
( as it is a Tv of a point in Vp)
3. Draw one projector from v. 4. FV - h’- VT’ always co-linear.
4. Now extend Fv to meet this projector.
This point is VT 5. TV - v - HT always co-linear.

These points are used to

solve next three problems.
173
PROBLEM 6 :- Fv of line AB makes 450 angle with XY line and measures 60 mm.
Line’s Tv makes 300 with XY line. End A is 15 mm above Hp and it’s VT is 10 mm
below Hp. Draw projections of line AB,determine inclinations with Hp & Vp and locate HT, VT.

b’ b’1

a’ 
450

SOLUTION STEPS:- 15
Draw xy line, one projector and x v h’
y
locate fv a’ 15 mm above xy. 10 300
Take 45 angle from a’ and
0

marking 60 mm on it locate point b’. VT’

Draw locus of VT, 10 mm below xy
a 
& extending Fv to this locus locate VT.
as fv-h’-vt’ lie on one st.line.
Draw projector from vt, locate v on xy.
From v take 300 angle downward as
Tv and it’s inclination can begin with v.
b b1
Draw projector from b’ and locate b I.e.Tv point.
Now rotating views as usual TL and
it’s inclinations can be found.
Name extension of Fv, touching xy as h’
and below it, on extension of Tv, locate HT. 174
PROBLEM 7 :
One end of line AB is 10mm above Hp and other end is 100 mm in-front of Vp.
It’s Fv is 450 inclined to xy while it’s HT & VT are 45mm and 30 mm below xy respectively.
Draw projections and find TL with it’s inclinations with Hp & VP.
b’ b’ 1 LOCUS OF b’ & b’1

a’ 450

10 v h’
X Y
30
45
VT’ HT
SOLUTION STEPS:-
Draw xy line, one projector and
locate a’ 10 mm above xy. 100
Draw locus 100 mm below xy for points b & b1
Draw loci for VT and HT, 30 mm & 45 mm
a 
below xy respectively.
Take 450 angle from a’ and extend that line backward
to locate h’ and VT, & Locate v on xy above VT.
Locate HT below h’ as shown.
Then join v – HT – and extend to get top view end b.
Draw projector upward and locate b’ Make a b & a’b’ dark. b b1 LOCUS OF b & b1
Now as usual rotating views find TL and it’s inclinations. 175
PROBLEM 8 :- Projectors drawn from HT and VT of a line AB
are 80 mm apart and those drawn from it’s ends are 50 mm apart.
End A is 10 mm above Hp, VT is 35 mm below Hp
while it’s HT is 45 mm in front of Vp. Draw projections,
locate traces and find TL of line & inclinations with Hp and Vp.
VT

b’ b’1

SOLUTION STEPS:- 55
1.Draw xy line and two projectors,
80 mm apart and locate HT & VT ,
35 mm below xy and 55 mm above xy Locus of a’ a’ 
respectively on these projectors. 10 50 v
2.Locate h’ and v on xy as usual. X y
h’ b b1
3.Now just like previous two problems,
Extending certain lines complete Fv & Tv
35
And as usual find TL and it’s inclinations.

a 
HT

80

176
 Instead of considering a & a’ as projections of first point,
if v & VT’ are considered as first point , then true inclinations of line with
Hp & Vp i.e. angles  &  can be constructed with points VT’ & V respectively.

b’ b1’

Then from point v & HT

a’
angles  &  can be drawn.
v &
X

Y From point VT’ & h’
angles  &  can be drawn.


VT’

THIS CONCEPT IS USED TO SOLVE

a
NEXT THREE PROBLEMS.

177
b b1
PROBLEM 9 :-
Line AB 100 mm long is 300 and 450 inclined to Hp & Vp respectively. b 1’
End A is 10 mm above Hp and it’s VT is 20 mm below Hp b’
.Draw projections of the line and it’s HT.
FV

Locus of a & a1’ a’ a1’

SOLUTION STEPS:- 10
X v h’
Draw xy, one projector Y
and locate on it VT and V. (45 )
0

20
Draw locus of a’ 10 mm above xy.  (300)
Take 300 from VT and draw a line.
Where it intersects with locus of a’ VT’
name it a1’ as it is TL of that part. HT
From a1’ cut 100 mm (TL) on it and locate point b1’
Now from v take 450 and draw a line downwards a a1
& Mark on it distance VT-a1’ I.e.TL of extension & name it a1
Extend this line by 100 mm and mark point b1.
Draw it’s component on locus of VT’
& further rotate to get other end of Fv i.e.b’ TV
Join it with VT’ and mark intersection point
(with locus of a1’ ) and name it a’
Now as usual locate points a and b and h’ and HT.

b b1

178
 PROBLEM 10 :-
A line AB is 75 mm long. It’s Fv & Tv make 450 and 600 inclinations with X-Y line resp
End A is 15 mm above Hp and VT is 20 mm below Xy line. Line is in first quadrant.
Draw projections, find inclinations with Hp & Vp. Also locate HT. b’ b 1’

FV

Locus of a & a1’ a’ a1’

15
X v h’
Y
600
20 

450
VT’
SOLUTION STEPS:-
Similar to the previous only change HT
is instead of line’s inclinations,
views inclinations are given. a a1
So first take those angles from VT & v
Properly, construct Fv & Tv of extension,
then determine it’s TL( V-a1)
TV
and on it’s extension mark TL of line
and proceed and complete it.

b b1
179
PROBLEM 11 :- The projectors drawn from VT & end A of line AB are 40mm apart.
End A is 15mm above Hp and 25 mm in front of Vp. VT of line is 20 mm below Hp.
If line is 75mm long, draw it’s projections, find inclinations with HP & Vp

b’ b1’

a’ a1’

15
X v Y
20 
25 
VT’
a

40mm
b b1

180
 GROUP (C)
CASES OF THE LINES IN A.V.P., A.I.P. & PROFILE PLANE.

b’ Line AB is in AIP as shown in above figure no 1.

It’s FV (a’b’) is shown projected on Vp.(Looking in arrow direction)
Here one can clearly see that the
Inclination of AIP with HP = Inclination of FV with XY line
a’ 


A A.V.P.

Line AB is in AVP as shown in above figure no 2..


a b
It’s TV (a b) is shown projected on Hp.(Looking in arrow direction)
Here one can clearly see that the
Inclination of AVP with VP = Inclination of TV with XY line
181
LINE IN A PROFILE PLANE ( MEANS IN A PLANE PERPENDICULAR TO BOTH HP & VP)
For T.V.

ORTHOGRAPHIC PATTERN OF LINE IN PROFILE PLANE

VP VT PP
a’ a”
A a’

FV LSV

b’ b’ b”
X Y
HT

a
B
TV
a
b
b HP

Results:-
1. TV & FV both are vertical, hence arrive on one single projector.
2. It’s Side View shows True Length ( TL)
3. Sum of it’s inclinations with HP & VP equals to 900 (  +  = 900 )
4. It’s HT & VT arrive on same projector and can be easily located
From Side View.

OBSERVE CAREFULLY ABOVE GIVEN ILLUSTRATION AND 2nd SOLVED PROBLEM.

182
PROBLEM 12 :- Line AB 80 mm long, makes 300 angle with Hp
and lies in an Aux.Vertical Plane 450 inclined to Vp. b’ Locus of b’ b1’
End A is 15 mm above Hp and VT is 10 mm below X-y line.
Draw projections, fine angle with Vp and Ht.

Locus of a’ & a1’ a’ a1’

15 v h’
X 450 Y
10 

VT HT

AVP 450 to VP

Locus of b’
b b1

183
 PROBLEM 13 :- A line AB, 75mm long, has one end A in Vp. Other end B is 15 mm above Hp
and 50 mm in front of Vp.Draw the projections of the line when sum of it’s
Inclinations with HP & Vp is 900, means it is lying in a profile plane.
Find true angles with ref.planes and it’s traces.

VT (VT) a”
a’
SOLUTION STEPS:-
Side View
After drawing xy line and one projector Front view ( True Length )

VP
Locate top view of A I.e point a on xy as
It is in Vp, b’ b”
Locate Fv of B i.e.b’15 mm above xy as a  (HT)
X HP Y
it is above Hp.and Tv of B i.e. b, 50 mm
below xy asit is 50 mm in front of Vp
Draw side view structure of Vp and Hp top view
and locate S.V. of point B i.e. b’’
From this point cut 75 mm distance on Vp and
Mark a’’ as A is in Vp. (This is also VT of line.) b
From this point draw locus to left & get a’ HT
Extend SV up to Hp. It will be HT. As it is a Tv
Rotate it and bring it on projector of b.
Now as discussed earlier SV gives TL of line
and at the same time on extension up to Hp & Vp 184
gives inclinations with those panes.
 PROBLEM NO.24
T.V. of a 75 mm long Line CD, measures 50 mm.
SOME CASES OF THE LINE End C is 15 mm below Hp and 50 mm in front of Vp.
IN DIFFERENT QUADRANTS. End D is 15 mm in front of Vp and it is above Hp.
Draw projections of CD and find angles with Hp and Vp.
REMEMBER:
BELOW HP- Means- Fv below xy
BEHIND V p- Means- Tv above xy. d’ d’1 LOCUS OF d’ & d’1

X Y
c’  d d1 LOCUS OF d & d1

c 

185
PROBLEM NO.25
End A of line AB is in Hp and 25 mm behind Vp.
End B in Vp.and 50mm above Hp.
Distance between projectors is 70mm.
Draw projections and find it’s inclinations with Ht, Vt.

LOCUS OF b’ & b’1

b’ b’1

a 

X a’  b b1 Y
LOCUS OF b & b1

70

186
PROBLEM NO.26
End A of a line AB is 25mm below Hp and 35mm behind Vp.
Line is 300 inclined to Hp.
There is a point P on AB contained by both HP & VP.
Draw projections, find inclination with Vp and traces.

a 
b’ b’1 LOCUS OF b’ & b’1

35

p p’
X y
p’1

25
=300
a’

LOCUS OF b & b1
b b1

187
PROBLEM NO.27
End A of a line AB is 25mm above Hp and end B is 55mm behind Vp.
The distance between end projectors is 75mm.
If both it’s HT & VT coincide on xy in a point,
35mm from projector of A and within two projectors,
b b1
Draw projections, find TL and angles and HT, VT.

55

a’

25
X Vt Y
Ht


a
35 b’ b’1

75

188
PROJECTION OF PLANE

189
 PROJECTIONS OF PLANES
In this topic various plane figures are the objects.

What is usually asked in the problem?

To draw their projections means F.V, T.V. & S.V.

What will be given in the problem?

1. Description of the plane figure.
2. It’s position with HP and VP.

In which manner it’s position with HP & VP will be described?

1.Inclination of it’s SURFACE with one of the reference planes will be given.
2. Inclination of one of it’s EDGES with other reference plane will be given
(Hence this will be a case of an object inclined to both reference Planes.)
Study the illustration showing
surface & side inclination given on next page. 190
 CASE OF A RECTANGLE – OBSERVE AND NOTE ALL STEPS.

SURFACE PARALLEL TO HP SURFACE INCLINED TO HP ONE SMALL SIDE INCLINED TO VP

PICTORIAL PRESENTATION PICTORIAL PRESENTATION PICTORIAL PRESENTATION

ORTHOGRAPHIC ORTHOGRAPHIC ORTHOGRAPHIC

TV-True Shape FV- Inclined to XY FV- Apparent Shape
FV- Line // to xy TV- Reduced Shape TV-Previous Shape
VP
VP VP
d1’ c1’

a’ d’ a1’ b1’
b’ c’

a d a1 d1

b c b1 c1
191
HP A HP B HP
C
 PROCEDURE OF SOLVING THE PROBLEM:
IN THREE STEPS EACH PROBLEM CAN BE SOLVED:( As Shown In Previous Illustration )
STEP 1. Assume suitable conditions & draw Fv & Tv of initial position.
STEP 2. Now consider surface inclination & draw 2nd Fv & Tv.
STEP 3. After this,consider side/edge inclination and draw 3rd ( final) Fv & Tv.

ASSUMPTIONS FOR INITIAL POSITION:

(Initial Position means assuming surface // to HP or VP)
1.If in problem surface is inclined to HP – assume it // HP
Or If surface is inclined to VP – assume it // to VP
2. Now if surface is assumed // to HP- It’s TV will show True Shape.
And If surface is assumed // to VP – It’s FV will show True Shape.
3. Hence begin with drawing TV or FV as True Shape.
4. While drawing this True Shape –
keep one side/edge ( which is making inclination) perpendicular to xy line
( similar to pair no. A on previous page illustration ).

Now Complete STEP 2. By making surface inclined to the resp plane & project it’s other view.
(Ref. 2nd pair B on previous page illustration )

Now Complete STEP 3. By making side inclined to the resp plane & project it’s other view.
(Ref. 3nd pair C on previous page illustration )

APPLY SAME STEPS TO SOLVE NEXT ELEVEN PROBLEMS

192
Problem 1: Read problem and answer following questions
Rectangle 30mm and 50mm 1. Surface inclined to which plane? ------- HP
sides is resting on HP on one 2. Assumption for initial position? ------// to HP
small side which is 300 inclined 3. So which view will show True shape? --- TV
to VP,while the surface of the 4. Which side will be vertical? ---One small side.
plane makes 450 inclination with Hence begin with TV, draw rectangle below X-Y
HP. Draw it’s projections. drawing one small side vertical.

Surface // to Hp Surface inclined to Hp

d’c’ c’1 d’1
c’d’
a’b’
a’ b’ 450 b’1 a’1 Y
X 300
a d a1 d1 Side
Inclined
to Vp

b c b1 c1

193
Problem 2: Read problem and answer following questions
A 300 – 600 set square of longest side 1 .Surface inclined to which plane? ------- VP
100 mm long, is in VP and 300 inclined 2. Assumption for initial position? ------// to VP
to HP while it’s surface is 450 inclined 3. So which view will show True shape? --- FV
to VP.Draw it’s projections 4. Which side will be vertical? ------longest side.

(Surface & Side inclinations directly given)

Hence begin with FV, draw triangle above X-Y
keeping longest side vertical.
a’ a’1

c’ c’1
side inclined to Hp
c’1

a’1

b’1
b’1
b’
300
X a
b 450 a1 b1 Y
a c
b c1
c
Surface // to Vp Surface inclined to Vp

194
Problem 3: Read problem and answer following questions
A 300 – 600 set square of longest side 1 .Surface inclined to which plane? ------- VP
100 mm long is in VP and it’s surface 2. Assumption for initial position? ------// to VP
450 inclined to VP. One end of longest 3. So which view will show True shape? --- FV
side is 10 mm and other end is 35 mm 4. Which side will be vertical? ------longest side.
above HP. Draw it’s projections
Hence begin with FV, draw triangle above X-Y
(Surface inclination directly given.
keeping longest side vertical.
Side inclination indirectly given)

First TWO steps are similar to previous problem.

Note the manner in which side inclination is given.
a’ a’1 End A 35 mm above Hp & End B is 10 mm above Hp.
So redraw 2nd Fv as final Fv placing these ends as said.
c’ c’1
c’1

a’1

35
b’1
b’1
b’
X 10 Y
a a1
b 450 b1
a c
b c1
c

195
Problem 4: Read problem and answer following questions
A regular pentagon of 30 mm sides is 1. Surface inclined to which plane? ------- HP
resting on HP on one of it’s sides with it’s 2. Assumption for initial position? ------ // to HP
surface 450 inclined to HP. 3. So which view will show True shape? --- TV
Draw it’s projections when the side in HP 4. Which side will be vertical? -------- any side.
makes 300 angle with VP Hence begin with TV,draw pentagon below
SURFACE AND SIDE INCLINATIONS X-Y line, taking one side vertical.
ARE DIRECTLY GIVEN.
d’ d’1
c’e’
e’1 c’1
b’ a’
X b’ a’ c’e’ d’ b’1 Y
450 a’1
a1 300
e e1
e1
a a1 b1

d1
d
d1 c1
b b1

c c1

196
 Problem 5: Read problem and answer following questions
A regular pentagon of 30 mm sides is resting 1. Surface inclined to which plane? ------- HP
on HP on one of it’s sides while it’s opposite 2. Assumption for initial position? ------ // to HP
vertex (corner) is 30 mm above HP. 3. So which view will show True shape? --- TV
Draw projections when side in HP is 300 4. Which side will be vertical? --------any side.
inclined to VP. Hence begin with TV,draw pentagon below
SURFACE INCLINATION INDIRECTLY GIVEN
X-Y line, taking one side vertical.
SIDE INCLINATION DIRECTLY GIVEN:

ONLY CHANGE is
the manner in which surface inclination is described:
One side on Hp & it’s opposite corner 30 mm above Hp. d’ d’1
Hence redraw 1st Fv as a 2nd Fv making above arrangement.
Keep a’b’ on xy & d’ 30 mm above xy. c’e’ c’1
30 e’1

b’ a’ c’e’ d’ a’
X b’ a’1 b’1 Y
300
e1 a1
e
e1
a a1 b1

d d1
d1 c1
b b1

c c1 197
 c’1
b’1
Problem 8: A circle of 50 mm diameter is a’ b’ d’ c’
resting on Hp on end A of it’s diameter AC 300 a’1 d’1 Y
X
which is 300 inclined to Hp while it’s Tv d1
450
d
is 450 inclined to Vp.Draw it’s projections.

a ca c1
1

Read problem and answer following questions

1. Surface inclined to which plane? ------- HP b b1
2. Assumption for initial position? ------ // to HP
3. So which view will show True shape? --- TV The difference in these two problems is in step 3 only.
4. Which diameter horizontal? ---------- AC In problem no.8 inclination of Tv of that AC is
Hence begin with TV,draw rhombus below given,It could be drawn directly as shown in 3rd step.
X-Y line, taking longer diagonal // to X-Y While in no.9 angle of AC itself i.e. it’s TL, is
given. Hence here angle of TL is taken,locus of c1
Is drawn and then LTV I.e. a1 c1 is marked and
final TV was completed.Study illustration carefully.
Problem 9: A circle of 50 mm diameter is
resting on Hp on end A of it’s diameter AC
which is 300 inclined to Hp while it makes c’1
450 inclined to Vp. Draw it’s projections. b’1
a’ b’ d’ c’
a’1 d’1
d d1
300
Note the difference in
a ca c1
construction of 3rd step 1

in both solutions.
b b1 199
 Read problem and answer following questions
Problem 10: End A of diameter AB of a circle is in HP 1. Surface inclined to which plane? ------- HP
A nd end B is in VP.Diameter AB, 50 mm long is 2. Assumption for initial position? ------ // to HP
300 & 600 inclined to HP & VP respectively. 3. So which view will show True shape? --- TV
Draw projections of circle. 4. Which diameter horizontal? ---------- AB
Hence begin with TV,draw CIRCLE below
X-Y line, taking DIA. AB // to X-Y

The problem is similar to previous problem of circle – no.9.

But in the 3rd step there is one more change.
Like 9th problem True Length inclination of dia.AB is definitely expected
but if you carefully note - the the SUM of it’s inclinations with HP & VP is 900.
Means Line AB lies in a Profile Plane.
Hence it’s both Tv & Fv must arrive on one single projector.
So do the construction accordingly AND note the case carefully..

300
X Y
600
SOLVE SEPARATELY
ON DRAWING SHEET
GIVING NAMES TO VARIOUS
POINTS AS USUAL,
AS THE CASE IS IMPORTANT

200
 Problem 11: Read problem and answer following questions
A hexagonal lamina has its one side in HP and 1. Surface inclined to which plane? ------- HP
Its apposite parallel side is 25mm above Hp and 2. Assumption for initial position? ------ // to HP
In Vp. Draw it’s projections.
Take side of hexagon 30 mm long.
3. So which view will show True shape? --- TV
4. Which diameter horizontal? ---------- AC
Hence begin with TV,draw rhombus below
X-Y line, taking longer diagonal // to X-Y
ONLY CHANGE is the manner in which surface inclination
is described:
One side on Hp & it’s opposite side 25 mm above Hp.
Hence redraw 1st Fv as a 2nd Fv making above arrangement.
Keep a’b’ on xy & d’e’ 25 mm above xy.

e’1 d’1

25 f’1 c1’
X a’b’ c’ f’ d’e’ a’1 b’1 Y
f f1 e1 d1
f1 c1
a e a1 e1
a1 b1 As 3rd step
b d b1 d1 redraw 2nd Tv keeping
c1
side DE on xy line.
c
Because it is in VP
as said in problem.

201
 FREELY SUSPENDED CASES.
IMPORTANT POINTS
1.In this case the plane of the figure always remains perpendicular to Hp.
Problem 12: 2.It may remain parallel or inclined to Vp.
An isosceles triangle of 40 mm long 3.Hence TV in this case will be always a LINE view.
base side, 60 mm long altitude Is 4.Assuming surface // to Vp, draw true shape in suspended position as FV.
freely suspended from one corner of (Here keep line joining point of contact & centroid of fig. vertical )
Base side.It’s plane is 450 inclined to 5.Always begin with FV as a True Shape but in a suspended position.
Vp. Draw it’s projections. AS shown in 1st FV.

a’1
a’
C

b’1
b’ g’ g’1
H
G c’ c’1
H/3
X Y

A B

b a,g c 450
First draw a given triangle
With given dimensions,
Locate it’s centroid position
And Similarly solve next problem
join it with point of suspension. of Semi-circle 202
 IMPORTANT POINTS
Problem 13 1.In this case the plane of the figure always remains perpendicular to Hp.
:A semicircle of 100 mm diameter 2.It may remain parallel or inclined to Vp.
is suspended from a point on its 3.Hence TV in this case will be always a LINE view.
straight edge 30 mm from the midpoint 4.Assuming surface // to Vp, draw true shape in suspended position as FV.
of that edge so that the surface makes (Here keep line joining point of contact & centroid of fig. vertical )
an angle of 450 with VP. 5.Always begin with FV as a True Shape but in a suspended position.
Draw its projections. AS shown in 1st FV.

A
a’
20 mm
p’
P

G b’
CG g’

c’

e’
d’
X Y

First draw a given semicircle

With given diameter,
Locate it’s centroid position b c a p,g d e
And
join it with point of suspension. 203
 To determine true shape of plane figure when it’s projections are given.
BY USING AUXILIARY PLANE METHOD
WHAT WILL BE THE PROBLEM?
Description of final Fv & Tv will be given.
You are supposed to determine true shape of that plane figure.

Follow the below given steps:

1. Draw the given Fv & Tv as per the given information in problem.
2. Then among all lines of Fv & Tv select a line showing True Length (T.L.)
(It’s other view must be // to xy)
3. Draw x1-y1 perpendicular to this line showing T.L.
4. Project view on x1-y1 ( it must be a line view)
5. Draw x2-y2 // to this line view & project new view on it.
It will be the required answer i.e. True Shape.

The facts you must know:-

If you carefully study and observe the solutions of all previous problems,
You will find
IF ONE VIEW IS A LINE VIEW & THAT TOO PARALLEL TO XY LINE,
THEN AND THEN IT’S OTHER VIEW WILL SHOW TRUE SHAPE:

NOW FINAL VIEWS ARE ALWAYS SOME SHAPE, NOT LINE VIEWS:
SO APPLYING ABOVE METHOD:
Study Next
WE FIRST CONVERT ONE VIEW IN INCLINED LINE VIEW .(By using x1y1 aux.plane) Four Cases
204
THEN BY MAKING IT // TO X2-Y2 WE GET TRUE SHAPE.
 Problem 14 Tv is a triangle abc. Ab is 50 mm long, angle cab is 300 and angle cba is 650.
a’b’c’ is a Fv. a’ is 25 mm, b’ is 40 mm and c’ is 10 mm above Hp respectively. Draw projections
of that figure and find it’s true shape.
As per the procedure-
1.First draw Fv & Tv as per the data.
2.In Tv line ab is // to xy hence it’s other view a’b’ is TL. So draw x1y1 perpendicular to it.
3.Project view on x1y1.
a) First draw projectors from a’b’ & c’ on x1y1.
b) from xy take distances of a,b & c( Tv) mark on these projectors from x1y1. Name points a1b1 & c1.
c) This line view is an Aux.Tv. Draw x2y2 // to this line view and project Aux. Fv on it.
for that from x1y1 take distances of a’b’ & c’ and mark from x2y= on new projectors.
4.Name points a’1 b’1 & c’1 and join them. This will be the required true shape.
Y1
a1b1 Y
2

b’ b’1
15
a’

15
C1
10 C’ X1
X X2 a’1
Y
c c’1

ALWAYS FOR NEW FV TAKE

DISTANCES OF PREVIOUS FV
300 650 AND FOR NEW TV, DISTANCES
a b
OF PREVIOUS TV
50 mm REMEMBER!! 205
 Problem 15: Fv & Tv of a triangular plate are shown.
Determine it’s true shape.

USE SAME PROCEDURE STEPS 50

OF PREVIOUS PROBLEM: 25
BUT THERE IS ONE DIFFICULTY: c’
15
NO LINE IS // TO XY IN ANY VIEW. a’
1’
MEANS NO TL IS AVAILABLE.
20
IN SUCH CASES DRAW ONE LINE b’
// TO XY IN ANY VIEW & IT’S OTHER 10
X Y
VIEW CAN BE CONSIDERED AS TL 15
x1
FOR THE PURPOSE. a c

HERE a’ 1’ line in Fv is drawn // to xy. 40

HENCE it’s Tv a-1 becomes TL. 1 c’1
a’1 y2
b
THEN FOLLOW SAME STEPS AND
c1
DETERMINE TRUE SHAPE. b’1
(STUDY THE ILLUSTRATION) y1
x2

ALWAYS FOR NEW FV TAKE b1

DISTANCES OF PREVIOUS FV
AND FOR NEW TV, DISTANCES d1
OF PREVIOUS TV
REMEMBER!! 206
PROBLEM 16: Fv & Tv both are circles of 50 mm diameter. Determine true shape of an elliptical plate.

ADOPT SAME PROCEDURE.

a c is considered as line // to xy.
Then a’c’ becomes TL for the purpose.
Using steps properly true shape can be
50D y1
Easily determined. b’ b1 y2
Study the illustration.
TL ac1 1
a’ c’ b’1
c’1
d’ d
X1 1
X d Y
X2

ALWAYS, FOR NEW FV

a’1
TAKE DISTANCES OF d’1
PREVIOUS FV AND a c TRUE SHAPE
FOR NEW TV, DISTANCES
OF PREVIOUS TV
REMEMBER!! 50 D. b

207
 Problem 17 : Draw a regular pentagon of
30 mm sides with one side 300 inclined to xy.
This figure is Tv of some plane whose Fv is
A line 450 inclined to xy.
Determine it’s true shape. b1
a1
c1
IN THIS CASE ALSO TRUE LENGTH
IS NOT AVAILABLE IN ANY VIEW. X1

BUT ACTUALLY WE DONOT REQUIRE

TL TO FIND IT’S TRUE SHAPE, AS ONE a’ e1 d1
VIEW (FV) IS ALREADY A LINE VIEW.
SO JUST BY DRAWING X1Y1 // TO THIS b’
VIEW WE CAN PROJECT VIEW ON IT e’
AND GET TRUE SHAPE:
c’ Y1
d’
STUDY THE ILLUSTRATION.. 450
X 300 Y
e

d
ALWAYS FOR NEW FV a
TAKE DISTANCES OF
PREVIOUS FV AND FOR
NEW TV, DISTANCES OF
PREVIOUS TV c
REMEMBER!! b
208
PROJECTION OF SOLID

209
 SOLIDS
To understand and remember various solids in this subject properly,
those are classified & arranged in to two major groups.
Group A Group B
Solids having top and base of same shape Solids having base of some shape
and just a point as a top, called apex.

Cylinder Cone

Prisms Pyramids

Triangular Square Pentagonal Hexagonal Triangular Square Pentagonal Hexagonal

Cube Tetrahedron
( A solid having ( A solid having
six square faces) 210
Four triangular faces)
 SOLIDS
Dimensional parameters of different solids.

Square Prism Square Pyramid Cylinder Cone

Apex Apex
Top
Rectangular Slant
Face Edge Triangular
Longer Base Face Base Base
Base
Edge

Corner of Edge Edge Corner of

Generators
base of of base
Imaginary lines
Base Base
generating curved surface
of cylinder & cone.

Sections of solids( top & base not parallel) Frustum of cone & pyramids.
( top & base parallel to each other) 211
 STANDING ON H.P RESTING ON H.P LYING ON H.P
On it’s base. On one point of base circle. On one generator.
(Axis perpendicular to Hp (Axis inclined to Hp (Axis inclined to Hp
And // to Vp.) And // to Vp) And // to Vp)

F.V. F.V. F.V.

X Y
While observing Fv, x-y line represents Horizontal Plane. (Hp)

X While observing Tv, x-y line represents Vertical Plane. (Vp) Y

T.V. T.V. T.V.

STANDING ON V.P RESTING ON V.P LYING ON V.P

On it’s base. On one point of base circle. On one generator.
Axis perpendicular to Vp Axis inclined to Vp Axis inclined to Vp 212
And // to Hp And // to Hp And // to Hp
 STEPS TO SOLVE PROBLEMS IN SOLIDS
Problem is solved in three steps:
STEP 1: ASSUME SOLID STANDING ON THE PLANE WITH WHICH IT IS MAKING INCLINATION.
( IF IT IS INCLINED TO HP, ASSUME IT STANDING ON HP)
( IF IT IS INCLINED TO VP, ASSUME IT STANDING ON VP)
IF STANDING ON HP - IT’S TV WILL BE TRUE SHAPE OF IT’S BASE OR TOP:
IF STANDING ON VP - IT’S FV WILL BE TRUE SHAPE OF IT’S BASE OR TOP.
BEGIN WITH THIS VIEW:
IT’S OTHER VIEW WILL BE A RECTANGLE ( IF SOLID IS CYLINDER OR ONE OF THE PRISMS):
IT’S OTHER VIEW WILL BE A TRIANGLE ( IF SOLID IS CONE OR ONE OF THE PYRAMIDS):
DRAW FV & TV OF THAT SOLID IN STANDING POSITION:
STEP 2: CONSIDERING SOLID’S INCLINATION ( AXIS POSITION ) DRAW IT’S FV & TV.
STEP 3: IN LAST STEP, CONSIDERING REMAINING INCLINATION, DRAW IT’S FINAL FV & TV.

GENERAL PATTERN ( THREE STEPS ) OF SOLUTION:

GROUP B SOLID. GROUP A SOLID. GROUP B SOLID. GROUP A SOLID.
CONE CYLINDER CONE CYLINDER
AXIS AXIS
AXIS AXIS INCLINED HP INCLINED HP
AXIS AXIS VERTICAL INCLINED HP
VERTICAL INCLINED HP

er AXIS er AXIS
AXIS AXIS TO VP AXIS TO VP
INCLINED VP AXIS INCLINED INCLINED
INCLINED VP VP VP

Three steps Three steps Three steps Three steps

If solid is inclined to Hp If solid is inclined to Hp If solid is inclined to Vp If solid is inclined
213to Vp
Study Next Twelve Problems and Practice them separately !!
 CATEGORIES OF ILLUSTRATED PROBLEMS!

PROBLEM NO.1, 2, 3, 4 GENERAL CASES OF SOLIDS INCLINED TO HP & VP

PROBLEM NO. 5 & 6 CASES OF CUBE & TETRAHEDRON

PROBLEM NO. 7 CASE OF FREELY SUSPENDED SOLID WITH SIDE VIEW.

PROBLEM NO. 8 CASE OF CUBE ( WITH SIDE VIEW)

PROBLEM NO. 9 CASE OF TRUE LENGTH INCLINATION WITH HP & VP.

PROBLEM NO. 10 & 11 CASES OF COMPOSITE SOLIDS. (AUXILIARY PLANE)

PROBLEM NO. 12 CASE OF A FRUSTUM (AUXILIARY PLANE)

214
 Solution Steps :
Problem 1. A square pyramid, 40 Triangular face on Hp , means it is lying on Hp:
mm base sides and axis 60 mm long, 1.Assume it standing on Hp.
2.It’s Tv will show True Shape of base( square)
has a triangular face on the ground 3.Draw square of 40mm sides with one side vertical Tv &
and the vertical plane containing the taking 50 mm axis project Fv. ( a triangle)
axis makes an angle of 450 with the 4.Name all points as shown in illustration.
5.Draw 2nd Fv in lying position I.e.o’c’d’ face on xy. And project it’s Tv.
VP. Draw its projections. Take apex 6.Make visible lines dark and hidden dotted, as per the procedure.
nearer to VP 7.Then construct remaining inclination with Vp
( Vp containing axis ic the center line of 2nd Tv.Make it 450 to xy as
shown take apex near to xy, as it is nearer to Vp) & project final Fv.

o’
a’1 b’1

Y
X a’b’ c’d’ d’1 c’1 o’1

a1
a d d1 a1

o1
o
b c c1 b1 (APEX
NEARER (APEX
TO V.P). AWAY
For dark and dotted lines
FROM V.P.)
1.Draw proper outline of new view DARK. 2. Decide direction of an observer.
3. Select nearest point to observer and draw all lines starting from it-dark. 215
4. Select farthest point to observer and draw all lines (remaining)from it- dotted.
 Solution Steps:
Problem 2: Resting on Hp on one generator, means lying on Hp:
A cone 40 mm diameter and 50 mm axis 1.Assume it standing on Hp.
is resting on one generator on Hp 2.It’s Tv will show True Shape of base( circle )
which makes 300 inclination with Vp 3.Draw 40mm dia. Circle as Tv &
taking 50 mm axis project Fv. ( a triangle)
Draw it’s projections. 4.Name all points as shown in illustration.
5.Draw 2nd Fv in lying position I.e.o’e’ on xy. And
For dark and dotted lines
1.Draw proper outline of new vie project it’s Tv below xy.
DARK. 6.Make visible lines dark and hidden dotted,
2. Decide direction of an observer. as per the procedure.
3. Select nearest point to observer 7.Then construct remaining inclination with Vp
and draw all lines starting from ( generator o1e1 300 to xy as shown) & project final Fv.
it-dark.
4. Select farthest point to observer o’
and draw all lines (remaining) a’1
from it- dotted.
h’1 b’1

g’1

f’1 c’
X a’ h’b’ c’ g f’ d’ e’ o’
e’1 d’1 1 Y o1
30
’
g g1
g1 o1
h f f1 h1 h1
f1 a1
a e e1 a1 o1
e1 b1

b d d1 b1
d1 216
c c1 c1
 Solution Steps:
Problem 3: Resting on Vp on one point of base, means inclined to Vp:
A cylinder 40 mm diameter and 50 mm 1.Assume it standing on Vp
2.It’s Fv will show True Shape of base & top( circle )
axis is resting on one point of a base 3.Draw 40mm dia. Circle as Fv & taking 50 mm axis project Tv.
circle on Vp while it’s axis makes 450 ( a Rectangle)
with Vp and Fv of the axis 350 with Hp. 4.Name all points as shown in illustration.
5.Draw 2nd Tv making axis 450 to xy And project it’s Fv above xy.
Draw projections.. 6.Make visible lines dark and hidden dotted, as per the procedure.
7.Then construct remaining inclination with Hp
( Fv of axis I.e. center line of view to xy as shown) & project final Tv.

4’d’ d’ 4’

3’
1’ a’ c’ a’ c’ 3’
1’

2’ b’ b’ 2’
X 350
Y
a bd c 450 c1
d1
b1

a1
3

4
2
1 24 3
217
1
 Solution Steps :
1.Assume it standing on Hp but as said on apex.( inverted ).
Problem 4:A square pyramid 30 mm base side 2.It’s Tv will show True Shape of base( square)
3.Draw a corner case square of 30 mm sides as Tv(as shown)
and 50 mm long axis is resting on it’s apex on Hp,
Showing all slant edges dotted, as those will not be visible from top.
such that it’s one slant edge is vertical and a
4.taking 50 mm axis project Fv. ( a triangle)
triangular face through it is perpendicular to Vp. 5.Name all points as shown in illustration.
Draw it’s projections. 6.Draw 2nd Fv keeping o’a’ slant edge vertical & project it’s Tv
7.Make visible lines dark and hidden dotted, as per the procedure.
8.Then redrew 2nd Tv as final Tv keeping a1o1d1 triangular face
perpendicular to Vp I.e.xy. Then as usual project final Fv.

a’ b’d’ c’ a’1
d’1 b’1
c’1

X o’ o’1 Y
d d1

a bo c ao1 b1 c1
1

218
 Solution Steps:
Problem 5: A cube of 50 mm long 1.Assuming standing on Hp, begin with Tv,a square with all sides
edges is so placed on Hp on one equally inclined to xy.Project Fv and name all points of FV & TV.
corner that a body diagonal is 2.Draw a body-diagonal joining c’ with 3’( This can become // to xy)
parallel to Hp and perpendicular to 3.From 1’ drop a perpendicular on this and name it p’
Vp Draw it’s projections. 4.Draw 2nd Fv in which 1’-p’ line is vertical means c’-3’ diagonal
must be horizontal. .Now as usual project Tv..
6.In final Tv draw same diagonal is perpendicular to Vp as said in problem.
Then as usual project final FV.
a’1

d’1
d’1
a’ b’d’ c’
3’
c’1

3’ 1’ 1’ 1’
X d
Y
d1

a c a1 c1

b b1 219
Problem 6:A tetrahedron of 50 mm Solution Steps
long edges is resting on one edge on As it is resting assume it standing on Hp.
Hp while one triangular face containing Begin with Tv , an equilateral triangle as side case as shown:
this edge is vertical and 450 inclined to First project base points of Fv on xy, name those & axis line.
Vp. Draw projections. From a’ with TL of edge, 50 mm, cut on axis line & mark o’
(as axis is not known, o’ is finalized by slant edge length)
IMPORTANT: Then complete Fv.
Tetrahedron is a In 2nd Fv make face o’b’c’ vertical as said in problem.
special type And like all previous problems solve completely.
of triangular
pyramid in which
base sides & o’1
slant edges are o’
equal in length. TL
Solid of four faces. a’1
Like cube it is also 900
described by One X a’ b’ b’1
c’ c’1 Y
dimension only.. 450
Axis length c c1
generally not given.
a o a1 o1

b b1 220
 FREELY SUSPENDED SOLIDS:
Positions of CG, on axis, from base, for different solids are shown below.

H
CG

H/2 CG
H/4

GROUP A SOLIDS GROUP B SOLIDS

( Cylinder & Prisms) ( Cone & Pyramids)

221
 Solution Steps:
Problem 7: A pentagonal pyramid In all suspended cases axis shows inclination with Hp.
30 mm base sides & 60 mm long axis, 1.Hence assuming it standing on Hp, drew Tv - a regular pentagon,corner case.
is freely suspended from one corner of 2.Project Fv & locate CG position on axis – ( ¼ H from base.) and name g’ and
base so that a plane containing it’s axis Join it with corner d’
remains parallel to Vp. 3.As 2nd Fv, redraw first keeping line g’d’ vertical.
Draw it’s three views. 4.As usual project corresponding Tv and then Side View looking from.

LINE d’g’ VERTICAL d”

o’ d’

c’e’ e” c”
FOR SIDE VIEW
g’
H a’b’
a” b”
g’
H/4 o”
IMPORTANT: a’ b’ c’ e’ d’ Y
X
When a solid is freely e1
e
suspended from a a1
corner, then line a
d1
joining point of o do
1
contact & C.G. b b1
remains vertical. c c1
( Here axis shows
inclination with Hp.)
So in all such cases,
assume solid standing
on Hp initially.) 222
Solution Steps: Problem 8:
1.Assuming it standing on Hp begin with Tv, a square of corner case. A cube of 50 mm long edges is so placed
2.Project corresponding Fv.& name all points as usual in both views. on Hp on one corner that a body diagonal
3.Join a’1’ as body diagonal and draw 2nd Fv making it vertical (I’ on xy) through this corner is perpendicular to Hp
4.Project it’s Tv drawing dark and dotted lines as per the procedure. and parallel to Vp Draw it’s three views.
5.With standard method construct Left-hand side view.
( Draw a 450 inclined Line in Tv region ( below xy).
Project horizontally all points of Tv on this line and
reflect vertically upward, above xy.After this, draw
horizontal lines, from all points of Fv, to meet these
lines. Name points of intersections and join properly. a’’
For dark & dotted lines
locate observer on left side of Fv as shown.)

d’’ b’’
a’ b’d’ c’

c’’
X 1’ Y
1’
d d1 1’

a c a1 c1

223
b b
Problem 9: A right circular cone, This case resembles to problem no.7 & 9 from projections of planes topic.
40 mm base diameter and 60 mm In previous all cases 2nd inclination was done by a parameter not showing TL.Like
long axis is resting on Hp on one Tv of axis is inclined to Vp etc. But here it is clearly said that the axis is 40 0 inclined
point of base circle such that it’s to Vp. Means here TL inclination is expected. So the same construction done in those
axis makes 450 inclination with Problems is done here also. See carefully the final Tv and inclination taken there.
Hp and 400 inclination with Vp. So assuming it standing on HP begin as usual.
Draw it’s projections.

o’ o’1

a’1
h’1 b’1

g’1 c’1

450 f’1 d’1

X a’ h’b’ c’ g’ f’ d’ e’
e’1
y
Axis True Length
g g1 400
h f h1 f1
Axis Tv Length
a e a1 1 e1
o1
Locus of
Center 1
b1 d1 1
b d
c c1
Axis Tv Length

224
Problem 10: A triangular prism,
40 mm base side 60 mm axis
is lying on Hp on one rectangular face
with axis perpendicular to Vp.
One square pyramid is leaning on it’s face F.V.
centrally with axis // to vp. It’s base side is
30 mm & axis is 60 mm long resting on Hp
on one edge of base.Draw FV & TV of
both solids.Project another FV
on an AVP 450 inclined to VP. X Y
450
Steps :
Draw Fv of lying prism
( an equilateral Triangle)
And Fv of a leaning pyramid. T.V.
Project Tv of both solids.
Draw x1y1 450 inclined to xy
and project aux.Fv on it. Aux.F.V.
Mark the distances of first FV
from first xy for the distances
of aux. Fv from x1y1 line.
Note the observer’s directions
Shown by arrows and further
steps carefully.

225
Problem 11:A hexagonal prism of
base side 30 mm longand axis 40 mm long,
is standing on Hp on it’s base with
one base edge // to Vp.
A tetrahedron is placed centrally
on the top of it.The base of tetrahedron is
a triangle formed by joining alternate corners
of top of prism..Draw projections of both solids. o’
Project an auxiliary Tv on AIP 450 inclined to Hp.

STEPS:
Draw a regular hexagon as Tv of
standing prism With one side // to xy Y1
and name the top points.Project it’s Fv – a’ b’ f’ c’ e’ d’
a rectangle and name it’s top.
Now join it’s alternate corners Fv
a-c-e and the triangle formed is base
of a tetrahedron as said. X Y Aux.Tv
Locate center of this triangle e1 o1
450
& locate apex o
f e
Extending it’s axis line upward f1 d1
mark apex o’
By cutting TL of edge of tetrahedron
equal to a-c. and complete Fv Tva o d a1 c1
of tetrahedron.
Draw an AIP ( x1y1) 450 inclined to xy b1
And project Aux.Tv on it by using similar b c
Steps like previous problem. X1

226
Problem 12: A frustum of regular hexagonal pyramid is standing on it’s larger base
On Hp with one base side perpendicular to Vp.Draw it’s Fv & Tv.
Project it’s Aux.Tv on an AIP parallel to one of the slant edges showing TL.
Base side is 50 mm long , top side is 30 mm long and 50 mm is height of frustum.

Fv
AIP // to slant edge
1’ 2’5’ 3’4’ Y1
Showing true length
i.e. a’- 1’
4
5 3
1 2

X a’ b’ e’ c’ d’ Y Aux.Tv
e d1
c1
d e1
Tv 5
4 X1 a1 b1
a 1
3
2
c

227
 SECTION OF SOLID &
SURFACE DEVELOPMENT

228
ENGINEERING APPLICATIONS
OF
THE PRINCIPLES
OF
PROJECTIONS OF SOLIDES.

1. SECTIONS OF SOLIDS.
2. DEVELOPMENT.
3. INTERSECTIONS.

STUDY CAREFULLY
THE ILLUSTRATIONS GIVEN ON
NEXT SIX PAGES !
229
 SECTIONING A SOLID. The action of cutting is called
An object ( here a solid ) is cut by SECTIONING a solid
some imaginary cutting plane &
to understand internal details of that object. The plane of cutting is called
SECTION PLANE.
Two cutting actions means section planes are recommended.

OBSERVER

A) Section Plane perpendicular to Vp and inclined to Hp. ASSUME

UPPER PART
( This is a definition of an Aux. Inclined Plane i.e. A.I.P.) REMOVED

NOTE:- This section plane appears (A)

as a straight line in FV.

B) Section Plane perpendicular to Hp and inclined to Vp.

( This is a definition of an Aux. Vertical Plane i.e. A.V.P.)
NOTE:- This section plane appears (B)
as a straight line in TV.
Remember:-
1. After launching a section plane ASSUME
LOWER PART
either in FV or TV, the part towards observer REMOVED
OBSERVER
is assumed to be removed.
2. As far as possible the smaller part is
230
assumed to be removed.
 For TV
ILLUSTRATION SHOWING
IMPORTANT TERMS
IN SECTIONING.

SECTION
PLANE

TRUE SHAPE
Of SECTION

x y

Apparent Shape
of section
SECTION LINES
(450 to XY)

SECTIONAL T.V.
231
Typical Section Planes
&
Typical Shapes
Of
Sections. Section Plane Ellipse
Section PlaneTriangle Through Generators
Through Apex

Section Plane Parallel Section Plane Hyperbola

to end generator. Parallel to Axis.

Ellipse Trapezium

Cylinder through Sq. Pyramid through

generators. all slant edges 232
 DEVELOPMENT OF SURFACES OF SOLIDS.
MEANING:-
ASSUME OBJECT HOLLOW AND MADE-UP OF THIN SHEET. CUT OPEN IT FROM ONE SIDE AND
UNFOLD THE SHEET COMPLETELY. THEN THE SHAPE OF THAT UNFOLDED SHEET IS CALLED
DEVELOPMENT OF LATERLAL SUEFACES OF THAT OBJECT OR SOLID.

LATERLAL SURFACE IS THE SURFACE EXCLUDING SOLID’S TOP & BASE.

ENGINEERING APLICATION:
THERE ARE SO MANY PRODUCTS OR OBJECTS WHICH ARE DIFFICULT TO MANUFACTURE BY
CONVENTIONAL MANUFACTURING PROCESSES, BECAUSE OF THEIR SHAPES AND SIZES.
THOSE ARE FABRICATED IN SHEET METAL INDUSTRY BY USING
DEVELOPMENT TECHNIQUE. THERE IS A VAST RANGE OF SUCH OBJECTS.

EXAMPLES:-
Boiler Shells & chimneys, Pressure Vessels, Shovels, Trays, Boxes & Cartons, Feeding Hoppers,
Large Pipe sections, Body & Parts of automotives, Ships, Aeroplanes and many more.

WHAT IS
To learn methods of development of surfaces of
OUR OBJECTIVE
different solids, their sections and frustums.
IN THIS TOPIC ?
1. Development is different drawing than PROJECTIONS.
But before going ahead, 2. It is a shape showing AREA, means it’s a 2-D plain drawing.
note following 3. Hence all dimensions of it must be TRUE dimensions.
Important points. 4. As it is representing shape of an un-folded sheet, no edges can remain hidden
And hence DOTTED LINES are never shown on development.
233
Study illustrations given on next page carefully.
 Development of lateral surfaces of different solids.
(Lateral surface is the surface excluding top & base)
Cylinder: A Rectangle
Pyramids: (No.of triangles)
Cone: (Sector of circle)

D
D
H= Height D= base diameter 
Prisms: No.of Rectangles R=Base circle radius. L= Slant edge.
L=Slant height. S = Edge of base
 R 3600
=L
H

S S H= Height S = Edge of base

Cube: Six Squares.

Tetrahedron: Four Equilateral Triangles

All sides
equal in length
234
 FRUSTUMS
DEVELOPMENT OF DEVELOPMENT OF
FRUSTUM OF CONE FRUSTUM OF SQUARE PYRAMID
Base side

Top side

 = R 3600
L

R= Base circle radius of cone

L= Slant height of cone L= Slant edge of pyramid
L1 = Slant height of cut part. L1 = Slant edge of cut part.

STUDY NEXT NINE PROBLEMS OF

SECTIONS & DEVELOPMENT 235
 Problem 1: A pentagonal prism , 30 mm base side & 50 mm axis Solution Steps:for sectional views:
is standing on Hp on it’s base whose one side is perpendicular to Vp. Draw three views of standing prism.
It is cut by a section plane 450 inclined to Hp, through mid point of axis. Locate sec.plane in Fv as described.
Draw Fv, sec.Tv & sec. Side view. Also draw true shape of section and Project points where edges are getting
Development of surface of remaining solid. Cut on Tv & Sv as shown in illustration.
C
Join those points in sequence and show
B Section lines in it.
D Make remaining part of solid dark.
Y1

A A B C D
E E A
d” c”

X1 e” b”

X a”
Y
e DEVELOPMENT
d
For True Shape: a For Development:
Draw x1y1 // to sec. plane
Draw development of entire solid. Name from
Draw projectors on it from c
cut-open edge I.e. A. in sequence as shown.
cut points.
b Mark the cut points on respective edges.
Mark distances of points
Join them in sequence in st. lines.
of Sectioned part from Tv,
Make existing parts dev.dark.
on above projectors from
x1y1 and join in sequence.
Draw section lines in it. 236
It is required true shape.
Problem 2: A cone, 50 mm base diameter and 70 mm axis is Solution Steps:for sectional views:
standing on it’s base on Hp. It cut by a section plane 450 inclined Draw three views of standing cone.
to Hp through base end of end generator.Draw projections, Locate sec.plane in Fv as described.
sectional views, true shape of section and development of surfaces Project points where generators are
of remaining solid. getting Cut on Tv & Sv as shown in
illustration.Join those points in
sequence and show Section lines in it.
Make remaining part of solid dark.
Y1 A
SECTIONAL S.V
o’ B

DEVELOPMENT C

X1 E
X a’ h’b’ c’ g’ f’ d’ e’ Y
g” h”f” a”e” b”d” c” F
g
For True Shape: h G
f
Draw x1y1 // to sec. plane
Draw projectors on it from For Development: H
cut points. a e
Draw development of entire solid.
Mark distances of points Name from cut-open edge i.e. A. A
of Sectioned part from Tv, in sequence as shown.Mark the cut
on above projectors from b d
points on respective edges.
x1y1 and join in sequence. c Join them in sequence in curvature.
Draw section lines in it. SECTIONAL T.V 237
Make existing parts dev.dark.
It is required true shape.
 Problem 3: A cone 40mm diameter and 50 mm axis is resting on one generator on Hp( lying on Hp)
which is // to Vp.. Draw it’s projections.It is cut by a horizontal section plane through it’s base
center. Draw sectional TV, development of the surface of the remaining part of cone.

Follow similar solution steps for Sec.views - True shape – Development as per previous problem!

o’ DEVELOPMENT
A
B
HORIZONTAL
SECTION PLANE C

D
X a’ h’b’ c’ g’ f’ d’ e’ o’ Y
g O E
g1
h f f1 h1 F

a e e1 a1 o1 G
O
H
b d d1 b1
c A
c1
SECTIONAL T.V
(SHOWING TRUE SHAPE OF SECTION)

238
 Note the steps to locate Problem 4: A hexagonal prism. 30 mm base side &
Points 1, 2 , 5, 6 in sec.Fv: 55 mm axis is lying on Hp on it’s rect.face with axis
Those are transferred to // to Vp. It is cut by a section plane normal to Hp and
1st TV, then to 1st Fv and 300 inclined to Vp bisecting axis.
a’ b’ c’ f’ d’ e’ Then on 2nd Fv. Draw sec. Views, true shape & development.

3
SECTIONAL F.V.
4
Use similar steps for sec.views & true shape.
NOTE: for development, always cut open object from
2 5 From an edge in the boundary of the view in which
sec.plane appears as a line.
Here it is Tv and in boundary, there is c1 edge.Hence
1 6 it is opened from c and named C,D,E,F,A,B,C.
X Y
8 7
f
f1

e a1 e1
a
A.V.P300 inclined to Vp
Through mid-point of axis.
b d b1 d1

AS SECTION PLANE IS IN T.V.,

c X1 c1 CUT OPEN FROM BOUNDRY EDGE C1 FOR DEVELOPMENT.

C D E F A B C

Y1

239
DEVELOPMENT
 Problem 5:A solid composed of a half-cone and half- hexagonal pyramid is
3 shown in figure.It is cut by a section plane 45 0 inclined to Hp, passing through
2 mid-point of axis.Draw F.v., sectional T.v.,true shape of section and
4 development of remaining part of the solid.
Y1 ( take radius of cone and each side of hexagon 30mm long and axis 70mm.)
5
1 O’ Note:
6 A Fv & TV 8f two solids
sandwiched
7 B Section lines style in both:
Development of
4’ half cone & half pyramid:
3’
X1 5’ F.V.
C
2’ 6’ 4 2
3

1 D
1’ 7’
X Y
d’e’ c’f’ g’b’ a’ O
f
E
g 7
6
e 5
SECTIONAL 7 4 5 6
4
TOP VIEW. a
F
1 3
d 2 b G
240
c
A
Problem 6: Draw a semicircle 0f 100 mm diameter and inscribe in it a largest TO DRAW PRINCIPAL
circle.If the semicircle is development of a cone and inscribed circle is some VIEWS FROM GIVEN
curve on it, then draw the projections of cone showing that curve. DEVELOPMENT.

E
D F
o’ R=Base circle radius. 4
L=Slant height. 3 5
 = R 3600 C
L
G
1’
7’ 2 6
B H
6’
2’
1
3’ 5’ 4’
 7
X a’ h’ b’ c’ g’ d’f’ e’ Y
A A
O
g L
6
h f Solution Steps:
5
Draw semicircle of given diameter, divide it in 8 Parts and inscribe in it
a largest circle as shown.Name intersecting points 1, 2, 3 etc.
a 7
o Semicircle being dev.of a cone it’s radius is slant height of cone.( L )
4 e
Then using above formula find R of base of cone. Using this data
1
draw Fv & Tv of cone and form 8 generators and name.
Take o -1 distance from dev.,mark on TL i.e.o’a’ on Fv & bring on o’b’
b 3 d and name 1’ Similarly locate all points on Fv. Then project all on Tv
2
on respective generators and join by smooth curve.
c 241
Problem 7:Draw a semicircle 0f 100 mm diameter and inscribe in it a largest TO DRAW PRINCIPAL
rhombus.If the semicircle is development of a cone and rhombus is some curve VIEWS FROM GIVEN
on it, then draw the projections of cone showing that curve. DEVELOPMENT.

Solution Steps:
o’ Similar to previous
Problem:
E
D F

C G

2’ 6’
B H
3’ 5’
a’ h’ b’ c’ g’ f’ d’ e’ 
X 1’ 7’ 4’ Y
g A A
O L
7 6
h f
5
R=Base circle radius.
L=Slant height.
a 4 e  = R 3600
L

b 3
d
2
1
c 242
Problem 8: A half cone of 50 mm base diameter, 70 mm axis, is standing on it’s half base on HP with it’s flat face
parallel and nearer to VP.An inextensible string is wound round it’s surface from one point of base circle and
brought back to the same point.If the string is of shortest length, find it and show it on the projections of the cone.

TO DRAW A CURVE ON
PRINCIPAL VIEWS
FROM DEVELOPMENT. Concept: A string wound
from a point up to the same
o’ Point, of shortest length
A Must appear st. line on it’s
Development.
B
Solution steps:
Hence draw development,
1 C Name it as usual and join
3’ A to A This is shortest
2’ 4’ Length of that string.
D
1’ 2
Further steps are as usual.
3 On dev. Name the points of
Intersections of this line with
X Y 4 E
a’ b’ c’ d’ e’ Different generators.Bring
O Those on Fv & Tv and join
a o 4 e
by smooth curves.
Draw 4’ a’ part of string dotted
3 As it is on back side of cone.
1 2
b d
c

A 243
Problem 9: A particle which is initially on base circle of a cone, standing
on Hp, moves upwards and reaches apex in one complete turn around the cone.
Draw it’s path on projections of cone as well as on it’s development.
Take base circle diameter 50 mm and axis 70 mm long.

It’s a construction of curve

o’ Helix of one turn on cone:
7’ DEVELOPMENT Draw Fv & Tv & dev.as usual
HELIX CURVE
6’ On all form generators & name.
A Construction of curve Helix::
5’
4’
B Show 8 generators on both views
3’ Divide axis also in same parts.
2’ 1
Draw horizontal lines from those
1’ C
points on both end generators.
X Y 2 1’ is a point where first horizontal
a’ h’b’ c’ gg’ f’ d’ e’ D Line & gen. b’o’ intersect.
3
2’ is a point where second horiz.
h f O 4 E Line & gen. c’o’ intersect.
7
6 6 5 In this way locate all points on Fv.
5
a
7
F Project all on Tv.Join in curvature.
O e For Development:
4
Then taking each points true
3 G
b 1 d Distance From resp.generator
2 from apex, Mark on development
c H & join.
A

244
ISOMETRIC PROJECTION

245
 ISOMETRIC DRAWING TYPICAL CONDITION.
IT IS A TYPE OF PICTORIAL PROJECTION IN THIS 3-D DRAWING OF AN OBJECT,
IN WHICH ALL THREE DIMENSIONS OF ALL THREE DIMENSIONAL AXES ARE
AN OBJECT ARE SHOWN IN ONE VIEW AND MENTAINED AT EQUAL INCLINATIONS
IF REQUIRED, THEIR ACTUAL SIZES CAN BE WITH EACH OTHER.( 1200)
MEASURED DIRECTLY FROM IT.

3-D DRAWINGS CAN BE DRAWN NOW OBSERVE BELOW GIVEN DRAWINGS.

IN NUMEROUS WAYS AS SHOWN BELOW. ONE CAN NOTE SPECIFIC INCLINATION
ALL THESE DRAWINGS MAY BE CALLED AMONG H, L & D AXES.
3-DIMENSIONAL DRAWINGS, ISO MEANS SAME, SIMILAR OR EQUAL.
OR PHOTOGRAPHIC HERE ONE CAN FIND
OR PICTORIAL DRAWINGS. EDUAL INCLINATION AMONG H, L & D AXES.
HERE NO SPECIFIC RELATION EACH IS 1200 INCLINED WITH OTHER TWO.
AMONG H, L & D AXES IS MENTAINED. HENCE IT IS CALLED ISOMETRIC DRAWING

H
H H
PURPOSE OF ISOMETRIC DRAWING IS TO UNDERSTAND 246
OVERALL SHAPE, SIZE & APPEARANCE OF AN OBJECT PRIOR TO IT’S PRODUCTION.
 SOME IMPORTANT TERMS:

ISOMETRIC AXES, LINES AND PLANES:

The three lines AL, AD and AH, meeting at point A and making
1200 angles with each other are termed Isometric Axes.
A
The lines parallel to these axes are called Isometric Lines.

The planes representing the faces of of the cube as well as

H
other planes parallel to these planes are called Isometric Planes.

ISOMETRIC SCALE:
When one holds the object in such a way that all three dimensions
are visible then in the process all dimensions become proportionally
inclined to observer’s eye sight and hence appear apparent in lengths.

This reduction is 0.815 or 9 / 11 ( approx.) It forms a reducing scale which

Is used to draw isometric drawings and is called Isometric scale.

In practice, while drawing isometric projection, it is necessary to convert

true lengths into isometric lengths for measuring and marking the sizes.
This is conveniently done by constructing an isometric scale as described
on next page.
247
 TYPES OF ISOMETRIC DRAWINGS

ISOMETRIC VIEW ISOMETRIC PROJECTION

Drawn by using True scale Drawn by using Isometric scale
( True dimensions ) ( Reduced dimensions )

D
4

H 2 C H
4

1 3

2
CONSTRUCTION OF ISOM.SCALE.
0 From point A, with line AB draw 300 and
1
450 inclined lines AC & AD resp on AD.
450 Mark divisions of true length and from
0 300
A B each division-point draw vertical lines
Isometric scale [ Line AC ] upto AC line.
The divisions thus obtained on248
AC
required for Isometric Projection give lengths on isometric scale.
1 Isometric view if the Shape is
ISOMETRIC SHAPE
OF
F.V. or T.V.
D
PLANE FIGURES H
RECTANGLE D
A D A
AS THESE ALL ARE
C
2-D FIGURES C
WE REQUIRE ONLY TWO A
ISOMETRIC AXES.
B C B B
IF THE FIGURE IS B
H
FRONT VIEW, H & L
TRIANGLE B
AXES ARE REQUIRED. 1
3
B 1 3
IF THE FIGURE IS TOP A A
VIEW, D & L AXES ARE 3
1
REQUIRED.
2 A 2 2
Shapes containing 4
Inclined lines should PENTAGON H E
be enclosed in a 1 E
4 1 D 4
rectangle as shown. D
Then first draw isom. A D A
E

of that rectangle and 1 3

then inscribe that 3 A C
C
shape as it is. 2 B
B C 3 B 249
2 2
 STUDY 2
Z
ILLUSTRATIONS

DRAW ISOMETRIC VIEW OF A

CIRCLE IF IT IS A TV OR FV.

FIRST ENCLOSE IT IN A SQUARE.

IT’S ISOMETRIC IS A RHOMBUS WITH
D & L AXES FOR TOP VIEW.
THEN USE H & L AXES FOR ISOMETRIC
WHEN IT IS FRONT VIEW.
FOR CONSTRUCTION USE RHOMBUS
METHOD SHOWN HERE. STUDY IT.
2

A B

3 4

D C

1 250
 3
STUDY
Z
ILLUSTRATIONS
25 R

DRAW ISOMETRIC VIEW OF THE FIGURE

SHOWN WITH DIMENTIONS (ON RIGHT SIDE)
CONSIDERING IT FIRST AS F.V. AND THEN T.V.
50 MM

IF FRONT VIEW

100 MM

IF TOP VIEW

251
 ISOMETRIC SHAPE IF F.V. IF T.V. 4
OF
PLANE FIGURES HEXAGON

AS THESE ALL ARE

2-D FIGURES
WE REQUIRE ONLY
TWO ISOMETRIC
AXES. CIRCLE

IF THE FIGURE IS
FRONT VIEW, H & L
AXES ARE REQUIRED.

IF THE FIGURE IS
TOP VIEW, D & L For Isometric of Circle/Semicircle use Rhombus method. Construct Rhombus
AXES ARE REQUIRED. of sides equal to Diameter of circle always. ( Ref. topic ENGG. CURVES.)

SEMI CIRCLE
For Isometric of
Circle/Semicircle
use Rhombus method.
Construct it of sides equal
to diameter of circle always. 252
( Ref. Previous two pages.)
 5

ISOMETRIC VIEW OF
PENTAGONAL PYRAMID
STANDING ON H.P.
(Height is added from center of pentagon)

ISOMETRIC VIEW OF BASE OF

PENTAGONAL PYRAMID
STANDING ON H.P.

4
4
D
D E
E

1 3 1 3
A C
A C
B
2
B
2

253
 6

ISOMETRIC VIEW OF
PENTAGONALL PRISM
LYING ON H.P.

4
H E
1 D

3
C
B
2
ISOMETRIC VIEW OF
HEXAGONAL PRISM
STANDING ON H.P. 254
 7

CYLINDER STANDING ON H.P.

CYLINDER LYING ON H.P.

255
 8
HALF CYLINDER
STANDING ON H.P.
( ON IT’S SEMICIRCULAR BASE)

HALF CYLINDER
LYING ON H.P.
( with flat face // to H.P.)
256
 9
ISOMETRIC VIEW OF
A FRUSTOM OF SQUARE PYRAMID
STANDING ON H.P. ON IT’S LARGER BASE.

60
FV

X Y

40 20

TV

257
 10

PROJECTIONS OF FRUSTOM OF ISOMETRIC VIEW

PENTAGONAL PYRAMID ARE GIVEN. OF
FRUSTOM OF PENTAGONAL PYRAMID
DRAW IT’S ISOMETRIC VIEW.

SOLUTION STEPS:
60
FV
FIRST DRAW ISOMETRIC
OF IT’S BASE.

x y THEN DRAWSAME SHAPE

E AS TOP, 60 MM ABOVE THE
1 4 BASE PENTAGON CENTER.
A
THEN REDUCE THE TOP TO
20 MM SIDES AND JOIN WITH
TV 40 20 D THE PROPER BASE CORNERS.

B
2 3
C
258
 ISOMETRIC VIEW OF 11
A FRUSTOM OF CONE
STANDING ON H.P. ON IT’S LARGER BASE.

60
FV

X Y

40 20

TV

259
PROBLEM: A SQUARE PYRAMID OF 30 MM BASE SIDES AND 12
50 MM LONG AXIS, IS CENTRALLY PLACED ON THE TOP OF A
CUBE OF 50 MM LONG EDGES.DRAW ISOMETRIC VIEW OF THE PAIR.

260
 13

c
PROBLEM: A TRIANGULAR PYRAMID
OF 30 MM BASE SIDES AND 50 MM a
LONG AXIS, IS CENTRALLY PLACED o
ON THE TOP OF A CUBE OF 50 MM p a
LONG EDGES. b
DRAW ISOMETRIC VIEW OF THE PAIR. o c
p

SOLUTION HINTS.
TO DRAW ISOMETRIC OF A CUBE IS SIMPLE. DRAW IT AS USUAL.

BUT FOR PYRAMID AS IT’S BASE IS AN EQUILATERAL TRIANGLE,

IT CAN NOT BE DRAWN DIRECTLY.SUPPORT OF IT’S TV IS REQUIRED.

SO DRAW TRIANGLE AS A TV, SEPARATELY AND NAME VARIOUS POINTS AS SHOWN.

AFTER THIS PLACE IT ON THE TOP OF CUBE AS SHOWN.
THEN ADD HEIGHT FROM IT’S CENTER AND COMPLETE IT’S ISOMETRIC AS SHOWN.
261
 14
PROBLEM:
A SQUARE PLATE IS PIERCED THROUGH CENTRALLY
BY A CYLINDER WHICH COMES OUT EQUALLY FROM BOTH FACES
OF PLATE. IT’S FV & TV ARE SHOWN. DRAW ISOMETRIC VIEW.

FV 30

10

30

30 D

50 +

50

TV

262
 15
PROBLEM:
A CIRCULAR PLATE IS PIERCED THROUGH CENTRALLY
BY A SQUARE PYRAMID WHICH COMES OUT EQUALLY FROM BOTH FACES
OF PLATE. IT’S FV & TV ARE SHOWN. DRAW ISOMETRIC VIEW.

FV 30

10

30

40 SQUARE

60 D
TV
263
 16
F.V. & T.V. of an object are given. Draw it’s isometric view.

10

20
40

FV

40

X Y

TV

50 D 30 D

264
 ISOMETRIC PROJECTIONS OF SPHERE & HEMISPHERE 17

450 r

300 R r
r
Isom. Scale
P

C
r r
R C
R TO DRAW ISOMETRIC PROJECTION
R OF A HEMISPHERE
P r
P Adopt same procedure.
C = Center of Sphere. Draw lower semicircle only.
Then around ‘C’ construct
P = Point of contact Rhombus of Sides equal to
R = True Radius of Sphere Isometric Diameter.
r = Isometric Radius. For this use iso-scale.
Then construct ellipse in
TO DRAW ISOMETRIC PROJECTION OF A SPHERE this Rhombus as usual
1. FIRST DRAW ISOMETRIC OF SQUARE PLATE. And Complete
2. LOCATE IT’S CENTER. NAME IT P. Isometric-Projection
3. FROM PDRAW VERTICAL LINE UPWARD, LENGTH ‘ r mm’ of Hemi-sphere.
AND LOCATE CENTER OF SPHERE “C”
4. ‘C’ AS CENTER, WITH RADIUS ‘R’ DRAW CIRCLE. 265
THIS IS ISOMETRIC PROJECTION OF A SPHERE.
PROBLEM: 18
A HEMI-SPHERE IS CENTRALLY PLACED
ON THE TOP OF A FRUSTOM OF CONE.
DRAW ISOMETRIC PROJECTIONS OF THE ASSEMBLY.

r
50 D
R r
30 D
r
50
P

50 D

FIRST CONSTRUCT ISOMETRIC SCALE.

USE THIS SCALE FOR ALL DIMENSIONS
IN THIS PROBLEM.

450

300

266
 19
A SQUARE PYRAMID OF 40 MM BASE SIDES AND 60 MM AXIS
IS CUT BY AN INCLINED SECTION PLANE THROUGH THE MID POINT
OF AXIS AS SHOWN.DRAW ISOMETRIC VIEW OF SECTION OF PYRAMID.

3’ 4’

3 1’2’

X Y
1 a d
1
4

2
o

3
b 2 c

267
 20

F.V. & T.V. of an object are given. Draw it’s isometric view.

50

O
X Y

20

25

O
25 20

268
 21
F.V. & T.V. of an object are given. Draw it’s isometric view.

35
FV

35

10
x y
O

10 20 30

40

70

TV
O

269
 22
F.V. & T.V. and S.V.of an object are given. Draw it’s isometric view.

FV

30 10 30 SV

30

10

30
x y

ALL VIEWS IDENTICAL

TV

270
 24
F.V. & T.V. and S.V.of an object are given. Draw it’s isometric view.

ALL VIEWS IDENTICAL

FV SV

x y

10
40 60

40
TV
60

271
F.V. & T.V. and S.V.of an object are given. Draw it’s isometric view.
25

ALL VIEWS IDENTICAL

FV SV

x y
10

40 60

40 TV

60
272
26

F.V. & T.V. and S.V.of an object are given. Draw it’s isometric view.

ORTHOGRAPHIC PROJECTIONS

FRONT VIEW L.H.SIDE VIEW

20

20

20
x y
O
50

20

30

O
20 20 20

TOP VIEW

273
 27
F.V. and S.V.of an object are given.
Draw it’s isometric view.

30 SQUARE
40 20

50

20
10

O 30
60
F.V.
S.V.
O

274
 28
F.V. & T.V. of an object are given. Draw it’s isometric view.

FV
40

10
O
30 D 45

10
50
O

80

TV

275
 29
F.V. & T.V. of an object are given. Draw it’s isometric view.

FV 40

X O 10 Y
100
10
25
TV
10 30 10
25
30 R O
20 D

276
 30
F.V. & T.V. of an object are given. Draw it’s isometric view.

30

FV
RECT.
SLOT

10 50
35

10
X Y
O
20 D

TV

60 D
30 D

O 277
 31
F.V. and S.V.of an object are given. Draw it’s isometric view.

10

25 15

25
40 10

25

25

O O
80 25

F.V. S.V.

278
F.V. & T.V. of an object are given. Draw it’s isometric view.
32

450

30
FV

40

X Y
O
30 D

40 TV

15
O 40
279
 33
F.V. and S.V.of an object are given.
Draw it’s isometric view.

HEX PART
30
20
20
40
20

O 50
20
15

O 30
100 60

280
 34
F.V. & T.V. of an object are given. Draw it’s isometric view.

20 40

F.V.
30

10
X Y
O

10

30

10

30
O 80

T.V.
281
 F.V. and S.V.of an object are given.
35
Draw it’s isometric view.

10 10 15

25

25
X Y
O 50 10
FV LSV

36
NOTE THE SMALL CHZNGE IN 2ND FV & SV.
DRAW ISOMETRIC ACCORDINGLY.

10

X Y
O FV LSV
282