DRAWING PUNCHES

－NORMAL・LAPPING－

Type Shank diameter D Catalog No.

Catalog No. － L － P・E・V・R・Q・A・K・F・S
～  Order
Equivalent to SP max35 m
ℓ in3
0.01
D0.03
SP2C 16 － 70.0 － P12.00－V9.00－A30－F65.0－S3
60～63HRC Lapping
SKD11
L－SP R0.5 R10
Regular type
SH Lapping

Dm5
SKH51 61～64HRC 3～25 Lapping 0.16
GL Days to Ship
L－SH
PH

0
H0.2
Powdered high-
64～67HRC Lapping
speed steel
L－PH 0.3 0.3 Price
5 0 B 0
Punch with locating dowel hole Equivalent to SP－C 0.3
F 0
60～63HRC 10～25 Lapping
SKD11
L－SP－C 0.3
L 0
Equivalent to MP
60～63HRC Lapping
Tapped punch SKD11
5～25
L－MP  SP－CT＝5＋0.01
＋0.03
Shape
MPH
Powdered high-
speed steel
64～67HRC Lapping
Lapping is applied to the area

from the punch tip up to B  P.557
L－MPH dimension.（However end face is
not lapped.）

Catalog No. 0.1mm increments 0.01mm increments

B H （M）
Type Shape D L min. P max.＊ Vmin.
5 3 2.00～ 2.99 1.00
－
7 －Lapping－ 4 2.00～ 3.99 1.00
8 Regular type SP L－SP 2A～4A・6A 40.0～80.0
8 5 2.00～ 4.99 1.20
3 （D3～25） SH L－SH
9 6 2.00～ 5.99 1.20
PH L－PH 2B～8B
11 4 8 3.00～ 7.99 1.50
13 13 5 With locating dowel hole SP－C L－SP－C 10 3.00～ 9.99 1.50
2C～10C （40.0～49.9）
16 （D10～25） 13 6.00～ 12.99 2.00
19 Tapped MP L－MP 16 50.0～100.0 10.00～ 15.99 3.00
6 2D～11D
19 23 （D5～25） MPH L－MPH 20 13.00～ 19.99 3.00
28 25 18.00～ 24.99 4.00
 Lapping cannot be used for shapes 2A・6A・8B・2C・3C・4C・6C・2D・3D・4D・5D・8D・9D・10D・11D.
（L 40.0～49.9） B＝8 If full length L is（40.0～49.9）, tip length B is 8mm in all cases.
－0.01
 P＞D－0.03ℓ＝0 If P＞D－0.03, D－0.03（press-in lead）is not included.
－0.01
 P can be the same value as D. P＝DP  m5・ℓ＝0 ＊If P＝D, tolerance of P is m5 and D－0.03（press-in lead）is not included.
（M） Tapped punch Can be used for MP・L－MP・MPH・L－MPH only.

Catalog No. － L － P（PC）

・E・V・R・Q・A・K・F・S －（BC・HC, etc.）
Alterations SP2C 16 － 75.0 － P12.00－V9.00－A30－F65.0－S3 － LKC－FKC

Alteration Code Spec. 1Code Alteration Code Spec. 1Code

P dimension change Chamfering of head
PC TCC
This improves the strength of the punch head.  P.1097
PC

Pmin.
P

PC≧ 0.01mm increments

2 ≧Vmin. 0.1 mm increments
TCC 0.5≦TCC≦ （H-D）/2
Tip length change
 If H≦5, then TCC is 0.5.
2≦BC≦BCmax. 0.1mm increments
 Cannot be combined with SRC.
 Full length L must be at least 30mm longer than tip length BC.
Addition of single key flat
B BC P
（PC）
1.00～1.19
BCmax.
15 KC
 Cannot be used for D5 MP・MPH・L－MP・L－MPH types.
Alterations to head

1.20～1.99 20
BC 2.00～2.99 30
3.00～3.99 35
Addition of double key flats in parallel
Alterations to tip

4.00～5.99 45
6.00～ 60 WKC
 Cannot be used for D5 MP・MPH・L－MP・L－MPH types.
Cannot be used
P dimension tolerance change  
P PKC P＋0.01 ＋0.005 with lapping. Head thickness is machined to a
0 ⇨ 0 RC tolerance of －0.04～0 relative to
0.04
0

the retainer surface.

Angle A tolerance change Cannot be used

A AKC A±30´⇨±10´
with lapping. Modification of head for use with select retainers（SLS）
SRC  For details, refer to P.675.  Can be used for D10～25.
Angle K tolerance change C
 annot be used
K KKC K±30´⇨±10´
with lapping. Head thickness tolerance change  C
 annot be used for
TKC punches with locating
5＋0.3 0 ⇨ 0
＋0.02
dowel holes.
R dimension tolerance  Cannot be used T
R RKC R±0.5⇨±0.05 with lapping. Head thickness tolerance change  C
 annot be used for
Can be used for 0.1≦R≦10. TKM 0 punches with locating
5＋0.3 0 ⇨－0.02 dowel holes.
Q dimension tolerance  Cannot be used
Q QKC Q±0.5⇨±0.05 with lapping. L dimension tolerance change
Can be used for 0.1≦Q≦10. L LKC
L＋0.3 ＋0.05
0 ⇨ 0
Head diameter change
Alterations to head

Others

HC D≦HC＜H
HC

F dimension tolerance change

H

0.1mm increments F FKC

F＋0.3 ＋0.05
0 ⇨ 0
Head thickness change 2≦TC＜5
0.1mm increments（If combined with TKC・TKM,
TC TC 0.01mm increments can be selected.） ℓ
0.01
D 0.03
No press-in lead ℓ≧3⇨ℓ＝0
NDC
559
T  The full length remains as specified.  Cannot be used for tapped punches. 560