Description of options

Option H2,
RS 485 Modbus communication
Multi-line 2 – version 2
4189340278F

• Hardware and software option

• RS 485 communication
DEIF A/S

• Modbus RTU or ASCII protocol

DEIF A/S, Frisenborgvej 33 Tel.: +45 9614 9614, Fax: +45 9614 9615
DK-7800 Skive, Denmark E-mail: [email protected], URL: www.deif.com
PPU/GPC/GPU Option H2, RS 485 Modbus communication

Table of contents

1. WARNINGS AND LEGAL INFORMATION ........................................................................... 3

LEGAL INFORMATION AND RESPONSIBILITY .................................................................................... 3
ELECTROSTATIC DISCHARGE AWARENESS ..................................................................................... 3
SAFETY ISSUES ............................................................................................................................ 3
PROGRAMMING ............................................................................................................................ 3
NOTES ......................................................................................................................................... 3
2. DESCRIPTION OF OPTION .................................................................................................. 4

3. HARDWARE .......................................................................................................................... 5
OPTION H2, SLOT #2.................................................................................................................... 6
4. MENU SETTINGS.................................................................................................................. 7
SETTING LISTS ............................................................................................................................. 7
UTILITY SOFTWARE CONFIGURATION ............................................................................................. 7
5. FUNCTIONAL DESCRIPTION .............................................................................................. 8
RS 485 WIRING ............................................................................................................................ 8
DATA TABLES ............................................................................................................................... 9
PARAMETER TABLE READING AND WRITING .................................................................................. 16
ADDRESS AND CHANNEL NUMBER OVERVIEW WITH UNITS ............................................................. 18
DIGITAL INPUT TABLE (READ ONLY 01H)....................................................................................... 28
DIGITAL OUTPUT TABLE (READ ONLY 01H).................................................................................... 29
6. TECHNICAL DATA.............................................................................................................. 30

This manual is valid for standard multi-line 2 PPU/GPC/GPU units with firmware version
2.30.0 or later.

DEIF A/S Page 2 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

1. Warnings and legal information

This chapter includes important information about general legal issues relevant in the handling
of DEIF products. Furthermore, some overall safety precautions will be introduced and
recommended. Finally, the highlighted notes, which will be used throughout this document, are
presented.

Legal information and responsibility

DEIF takes no responsibility for installation or operation of the generator set. If there is any doubt
about how to install or operate the generator controlled by the multi-line 2 unit, the company
responsible for the installation or the operation of the set must be contacted.

The multi-line 2 units are not to be opened by unauthorized personnel. If opened

anyway, the warranty will be lost.

Electrostatic discharge awareness

Sufficient care must be taken to protect the terminals against static discharges during the
installation. Once the unit is installed and connected, these precautions are no longer necessary.

Safety issues
Installing the multi-line 2 unit implies work with dangerous currents and voltages. Therefore, the
installation should only be carried out by authorized personnel who understand the risks involved
in the working with live electrical equipment.

Programming
The multi-line unit is delivered from factory with factory settings. These are based on an average
value and do not necessarily represent values matching the generator set in question.
Precautions must be taken to check this before running the generator set.

Notes
Throughout this document a number of notes with helpful user information will be presented. To
ensure that these notes are noticed, they will be highlighted in order to separate them from the
general text.

Xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

DEIF A/S Page 3 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

2. Description of option

This document describes the functionality of Modbus communication multi-line PPU/GPC/GPU.

Function ANSI no.

RS 485 Modbus communication -

DEIF A/S Page 4 of 30

DEIF A/S
PPU/GPC/GPU

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

SLOT #1 SLOT #2
SLOT #3 SLOT #4
37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72

Ethernet
Service port Display

r
ok
ib i

we
ck
in h

Po
he
m

c
ar

elf
Al

S
3. Hardware

73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97

SLOT #5 SLOT #6
SLOT #7 SLOT #8
98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133
the multi-line unit. The slots are positioned in the unit as follows (seen from the top of the unit):
Option H2, RS 485 Modbus communication

The multi-line 2 option H2 is carried out by adding hardware in slot #2 to the basic hardware of

Page 5 of 30
PPU/GPC/GPU Option H2, RS 485 Modbus communication

Option H2, slot #2

Term. Function Description

29 DATA + (A) Modbus RTU/ASCII, RS 485
30 GND
31 DATA - (B)
32 Not used
33 DATA + (A)
34 Not used
35 DATA - (B)
36 Not used

Terminals 29 and 33 are internally connected.

Terminals 31 and 35 are internally connected.

DEIF A/S Page 6 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

4. Menu settings

The setup of parameters is done via the display or the PC utility software (USW).

Setting lists

4050 Communication control enable/disable control

No. Setting Min. setting Max. setting Factory

setting
4051 Comm. control Power OFF ON OFF
4052 Comm. control Frequency OFF ON OFF
4053 Comm. control Voltage OFF ON OFF
4054 Comm. control var OFF ON OFF
4055 Comm. control PF OFF ON OFF

Selecting communication control ON will overrule external and internal settings.

4060 External communication control

No. Setting Min. setting Max. setting Factory

setting
4061 External comm. ID 1 247 3
4062 External comm. Baud rate 9600 19200 9600
4063 External comm. Mode RTU ASCII RTU

The mode ASCII is used for modem communication (ASCII: 7 data bit. RTU: 8 data bit).

4090 External communication error indication

No. Setting Min. setting Max. setting Factory

setting
4091 External comm. error Delay 1.0 s 100.0 s 10.0 s
4092 External comm. error Relay output A R0 (none) R4 (relay 4) R0 (none)
4093 External comm. error Relay output B R0 (none) R4 (relay 4) R0 (none)
4094 External comm. error Enable OFF ON OFF

Regarding relay settings and selections: See description in the Designer’s Reference
Handbook.

The max. no. of alarm output relays available are dependent on the hardware options
selected.

Utility software configuration

®
The utility software is a Windows based software which can be downloaded from the website
www.deif.com.

To adjust the parameters through the utility software, a computer must be connected to the multi-
line 2 and the parameters must be uploaded to the computer.

DEIF A/S Page 7 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

5. Functional description

RS 485 wiring

Multi-line 2 Multi-line 2 Multi-line 2

A GND B A B A GND B A B A GND B A B

29 30 31 33 35 29 30 31 33 35 29 30 31 33 35

PLC

Normally the Modbus does not need bias resistors (end terminators), they are only
needed in case of very long lines and/or many nodes (>32) on the Modbus network.
If bias resistors are needed, base the calculation on the following data:
- A line internal pull-up bias resistor: 22 kΩ
- B line internal pull-down bias resistor: 22 kΩ
- Receiver input sensitivity: +/-200 mV
- Receiver input impedance: 12 kΩ

Cable: Belden 3105A or equivalent.

2
22 AWG (0.6 mm ) single twisted pair, shielded, <40 mΏ/m, min. 95% shield coverage.

DEIF A/S Page 8 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

Data tables

Measurement table (read only) (function code 03h)

Address Content Type

0 Application version
1 UL1-L2 Generator voltage. Measured in [V]
2 UL2-L3 Generator voltage. Measured in [V]
3 UL3-L1 Generator voltage. Measured in [V]
4 UL1-N Generator voltage. Measured in [V]
5 UL2-N Generator voltage. Measured in [V]
6 UL3-N Generator voltage. Measured in [V]
7 FGEN Generator frequency. Measured in [Hz/100]
8 IL1 Generator current. Measured in [A]
9 IL2 Generator current. Measured in [A]
10 IL3 Generator current. Measured in [A]
11 Cos-phi -99...0...100 Generator cosinus-phi. Measured in cos-phi:100
Negative value means capacitive cos-phi
12 PGEN Generator active power. Measured in [kW]. Negative value
means reverse power
13 QGEN Generator reactive power. Measured in [kvar]. Positive value
means generated inductive reactive power
14 UBBL1-L2 Busbar. Measured in [V]
15 FBB Busbar frequency L1. Measured in [Hz/100]
16 [HI] RGEN Export Reactive energy counter, exported reactive power. Measured
17 [LO] in [kvarh]. Max. 300000 Mvarh
18 [HI] EGEN Export Energy counter, exported power. Measured in [kWh]. Max.
19 [LO] 300000MWh
20 Alarms Bit 0 1010. Reverse power
Bit 1 1020. Overcurrent step 1
Bit 2 1030. Overcurrent step 2
Bit 3 1060. Overcurrent inverse
Bit 4 1070. Fast overcurrent
Bit 5 1080. High overcurrent
Bit 6 Reserved
Bit 7 1100. U-DG High step 1
Bit 8 1110. U-DG High step 2
Bit 9 1120. U-DG Low step 1
Bit 10 1130. U-DG Low step 2
Bit 11 1140. f-DG High step 1
Bit 12 1150. f-DG High step 2
Bit 13 1160. f-DG Low step 1
Bit 14 1170. f-DG Low step 2
Bit 15 1180. U-BB High step 1

DEIF A/S Page 9 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

Address Content Type

21 Alarms Bit 0 1190. U-BB High step 2
Bit 1 1200. U-BB Low step 1
Bit 2 1210. U-BB Low step 2
Bit 3 1220. f-BB High step 1
Bit 4 1230. f-BB High step 2
Bit 5 1240. f-BB Low step 1
Bit 6 1250. f-BB Low step 2
Bit 7 1260. Overload step 1
Bit 8 1270. Overload step 2
Bit 9 1280. Unbalance current
Bit 10 1290. Unbalance voltage
Bit 11 1300. Q import
Bit 12 1310. Q export
Bit 13 1320. Gen. neg. sequence current
Bit 14 1330. Gen. neg. sequence voltage
Bit 15 Reserved
22 Alarms Bit 0 1350. df/dt (ROCOF)
Bit 1 1360. Vector jump
Bit 2 3440. 4-20 mA input no. 1.1
Bit 3 3460. 4-20 mA input no. 2.1
Bit 4 3480. 4-20 mA input no. 3.1
Bit 5 3500. 4-20 mA input no. 4.1
Bit 6 3520. 4-20 mA input no. 5.1
Bit 7 3540. 4-20 mA input no. 6.1
Bit 8 3560. 4-20 mA input no. 7.1
Bit 9 3580. 4-20 mA input no. 8.1
Bit 10 3600. Pt 100 no. 1.1
Bit 11 3620. Pt 100 no. 2.1
Bit 12 3640. Overspeed (Tacho) 1
Bit 13 3120. Dig. input term. 23
Bit 14 3130. Dig. input term. 24
Bit 15 3140. Dig. input term. 25
23 Alarms Bit 0 3150. Dig. input term. 26
Bit 1 3160. Dig. input term. 27
Bit 2 3170. Dig. input term. 43
Bit 3 3180. Dig. input term. 44
Bit 4 3190. Dig. input term. 45
Bit 5 3200. Dig. input term. 46
Bit 6 3210. Dig. input term. 47
Bit 7 3220. Dig. input term. 48
Bit 8 3230. Dig. input term. 49
Bit 9 3240. Dig. input term. 50
Bit 10 3250. Dig. input term. 51
Bit 11 3260. Dig. input term. 52
Bit 12 3270. Dig. input term. 53
Bit 13 3280. Dig. input term. 110
Bit 14 3290. Dig. input term. 111
Bit 15 3300. Dig. input term. 112

DEIF A/S Page 10 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

Address Content Type

24 Alarms Bit 0 3310. Dig. input term. 113
Bit 1 3320. Dig. input term. 114
Bit 2 3330. Dig. input term. 115
Bit 3 3340. Dig. input term. 116
Bit 4 3350. Dig. input term. 117
Bit 5 3360. Dig. input term. 118
Bit 6 3370. Dig. input term. 127
Bit 7 3380. Dig. input term. 128
Bit 8 3390. Dig. input term. 129
Bit 9 3400. Dig. input term. 130
Bit 10 3410. Dig. input term. 131
Bit 11 3420. Dig. input term. 132
Bit 12 3430. Dig. input term. 133
Bit 13 3660. Oil pressure (VDO sensor 1) 1
Bit 14 3680. Water temperature (VDO sensor 2) 1
Bit 15 3700. Fuel level (VDO sensor 3) 1
25 System Bit 0 Sync. fail. alarm
alarms/status Bit 1 Generator breaker ON failure
Bit 2 Generator breaker OFF failure
Bit 3 Generator breaker position fail. alarm
Bit 4 Phase sequence error alarm
Bit 5 Governor regulator fail. alarm
Bit 6 AVR regulator fail. alarm
Bit 7 Battery voltage alarm
Bit 8 Sync. timer runout
26 Alarm relay Bit 0 Relay 0
status Bit 1 Relay 1
Bit 2 Relay 2
Bit 3 Relay 3
Bit 4 Relay 4
Bit 5 Relay 5
Bit 6 Relay 6
Bit 7 Relay 7
Bit 8 Relay 8
Bit 9 Relay 9 (Stop engine)
Bit 10 Relay 10
Bit 11 Relay 11
Bit 12 Relay 12
Bit 13 Relay 13
Bit 14 Relay 14
Bit 15 Relay 15
27 Status Bit 0 Mode 1
Bit 1 Mode 2
Bit 2 Mode 3
Bit 3 Mode 4
Bit 4 Mode 5
Bit 5 Mode 6
Bit 6 De-load
Bit 7 Start sync./reg.
Bit 8 Alarm inhibit
Bit 9 Breaker position ON
Bit 10 Synchronising
Bit 11 Relay 16

DEIF A/S Page 11 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

Address Content Type

28 Bit 0 3450. 4-20 mA input no. 1.2
Bit 1 3470. 4-20 mA input no. 2.2
Bit 2 3490. 4-20 mA input no. 3.2
Bit 3 3510. 4-20 mA input no. 4.2
Bit 4 3530. 4-20 mA input no. 5.2
Bit 5 3550. 4-20 mA input no. 6.2
Bit 6 3570. 4-20 mA input no. 7.2
Bit 7 3590. 4-20 mA input no. 8.2
Bit 8 3610. Pt 100 no. 1.2
Bit 9 3630. Pt 100 no. 2.2
Bit 10 3650. Overspeed (Tacho) 2
Bit 11 3670. Oil pressure (VDO sensor 1) 2
Bit 12 3690. Water temperature (VDO sensor 2) 2
Bit 13 3710. Fuel level (VDO sensor 3) 2
Bit 14 1370. Zero sequence current
Bit 15 1380. Zero sequence voltage
29 UDG-max Generator max. voltage. Measured in [V]
30 UDG-min Generator min. voltage. Measured in [V]
31 UBBL2-L3 Busbar voltage. Measured in [V]
32 UBBL3-L1 Busbar voltage. Measured in [V]
33 UBB-max Busbar max. voltage. Measured in [V]
34 UBB-min Busbar min. voltage. Measured in [V]
35 UBBL1-N Busbar voltage. Measured in [V]
36 UBBL2-N Busbar voltage. Measured in [V]
37 UBBL3-N Busbar voltage. Measured in [V]
38 Running time Hour
39 RPM RPM
40 SGEN Generator apparent power. Measured in [kVA]
41 VDO 1 Oil pressure in [bar]/10
o
42 VDO 2 Water temp. in [ C]
43 VDO 3 Fuel level in [%]
44 PHIBBL1-L2 0...359 Busbar phase angle. Measured in [deg.]
45 PHIBBL1-DGL1 0...359 Busbar/generator phase angle. Measured in [deg.]
46 CBoper Circuit breaker operations counter
47 USUPPLY Supply voltage. Measured in [V/10]
48 PT100 (1) -40 – 250 temperature in deg. (engine interface)
49 PT100 (2) -40 – 250 temperature in deg. (engine interface)
50 Control register table address 0
51 Control register table address 1
52 Control register table address 3
53 Control register table address 4
54 Control register table address 5
55 Analogue input no. 1 (scaled)
56 Analogue input no. 2 (scaled)
57 Analogue input no. 3 (scaled)
58 Analogue input no. 4 (scaled)
59 Analogue input no. 5 (scaled)
60 Analogue input no. 6 (scaled)
61 Analogue input no. 7 (scaled)
62 Analogue input no. 8 (scaled)
63 No. of alarms

DEIF A/S Page 12 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

Address Content Type

64 No. of unacknowledged alarms
65 Not used
66 Not used
67 Not used
68 Not used
69 Not used
70 Not used
71 Not used
72 Not used
73 Not used
74 Hi RGEN Import Reactive energy counter, imported reactive power. Measured
75 Lo in [kvarh]. Max. 300000 Mvarh
76 Hi EGEN Import Energy counter, imported power. Measured in [kWh]. Max.
77 Lo 300000MWh

DEIF A/S Page 13 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

Control register table (write only) (function code 10h)

Address Content Description

0 Power regulator 0...100% of nominal power
set point Activated in menu 4051
1 PF regulator set 60...100 stated as PF value/100. The value 100 means PF =
point 1
Activated in menu 4055
2 Control Bit 0 This bit must be 1 when writing the command
command word
If the bit is 0, the control command is don’t care
Bit 1 Mode 1
Bit 2 Mode 2
Bit 3 Mode 3
Bit 4 Mode 4
Bit 5 Mode 5
Bit 6 Mode 6
Bit 7 De-load
Bit 8 Start sync./reg.
Bit 9 Alarm inhibit
Bit 10 Alarm ack. This bit is automatically reset in
multi-line 2
Bit 11 Second set point (protection functions)
Bit 12 Remote mode (option M1/M2)*
Bit 13 Local mode (option M1/M2)*
3 Frequency -500...500%/10. Based on nominal frequency
regulator set Activated in menu 4052
point
4 Voltage -100...100%/10 of nominal voltage
regulator set Activated in menu 4053
point
5 Reactive power -250...250% of nominal power. A negative value means
regulator set capacitive reactive power, and a positive value means
point inductive reactive power.
Activated in menu 4054
Date and time setting
19000 Year setting 2003...2099
19001 Month setting 1...12
19002 Date setting 1...31
19003 Day setting 1...7 (1 = Monday, 7 = Sunday)
19004 Hour setting 0...23
19005 Second setting 0...59

If terminal 26 "Control via external communication" is activated, the regulators are

controlled via the Modbus. The digital inputs "Alarm ack" and "Alarm inhibit" are always
handled even if terminal 26 = ON. The date and time settings do not require terminal 26
to be ON.

In menu 4050 it is selected, if a set point is to be controlled by the control registers.

(Mode 3 and/or mode 6 must be on). It is possible to write to the control registers also
when terminal 26 = OFF, but the regulators will only respond if terminal 26 = ON. The
contents of the control registers are not lost in case of supply failure, so frequent
updates are not necessary.

*Address 2 bits 12 and 13: The selection of remote/local mode must be made with a
pulse. If the command is repeated, it will overrule the selection from the display.

DEIF A/S Page 14 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

Example how to control the frequency via the Modbus:

• Activate terminal 26
• Activate frequency control register in menu 4052
• Write the control command address 2. Bit 0 = ON, Bit 8 = ON
• Write in the control register address 3 the desired frequency offset

Command flags table (write only) (function code 0Fh)

Address Content Description

0 Mode 1
1 Mode 2
2 Mode 3
3 Mode 4
4 Mode 5
5 Mode 6
6 De-load
7 Start sync./reg.
8 Alarm inhibit
9 Alarm ack. This bit is automatically reset in multi-line 2
nd
10 2 set point Use second set of protection parameters
11 Remote* Remote running mode (option M1/M2)
12 Local* Local running mode (option M1/M2)

Same function as address 2 in the control register table.

*The selection of remote/local mode must be made with a pulse. If the command is
repeated, it will overrule the selection from the display.

Status flags table (read only) (function code 01h)

Address Content Description

0 Mode 1
1 Mode 2
2 Mode 3
3 Mode 4
4 Mode 5
5 Mode 6
6 De-load
7 Start sync./reg.
8 Alarm inhibit
9 Breaker pos. on
10 Synchronising
11 Remote

DEIF A/S Page 15 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

Parameter table reading and writing

The entire setting of parameters can be made using the Modbus. The combination of function and
address areas used is described in the following:

Function 01 (01h) read flag status

Reads the ON/OFF status of discrete flags in the slave.

Address area for reading of status flags

Multi-line 2 Multi-line 2 Address area

Data to request Table
Status Status table 0-499 (status address)
Alarm active Parameter table 500-999 (status address + 500)
Alarm acknowledge Parameter table 1000-1499 (status address + 1000)
Digital input Digital input table 1500-1599 (status address + 1500)
Digital output Digital output table 2000-2499 (status address + 2000)

The max. number of data query is limited of the length of the actual table.

Function 03 (03h) read registers

Reads the binary values of registers in the slave.

Address area for reading of registers

Multi-line 2 Multi-line 2 Address area

Data to request Table
Measuring values Measuring values table 0-499 (data address)
Timers used Parameter table 500-999 (data address + 500)
Timers minimum Parameter table 1000-1499 (data address + 1000)
Timers maximum Parameter table 1500-1599 (data address + 1500)
Values used Parameter table 2000-2499 (data address + 2000)
Values minimum Parameter table 2500-2999 (data address + 2500)
Values maximum Parameter table 3000-3499 (data address + 3000)

The max. number of data query is limited of the length of the actual table or max.
100.

DEIF A/S Page 16 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

Function 15 (0Fh) write multiple flags

Writes each flag (0 x reference) in a sequence of flags to either ON or OFF.

Address area for writing of status flags

Multi-line 2 Multi-line 2 Address area

Data to request Table
Commands Command table 0-499 (command address)
Alarm acknowledge Parameter table 1000-1499 (command address +
1000)

The max. number of data query is limited of the length of the actual table.

Function 16 (10h) write register

Writes values into a sequence of registers.

Address area for writing of registers

Multi-line 2 Multi-line 2 Address area

Data to request Table
Control Control table set point 0-499 (control address)
Timers used Parameter table 500-999 (control address + 500)
Values used Parameter table 2000-2499 (control address + 2000)

The max. number of data query is limited of the length of the actual table or max.
100.

DEIF A/S Page 17 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

Address and channel number overview with units

Offset Ch. no. Content Value Delay

address unit unit
0 - - - -
1 1010 Reverse power %/10 1/10s
2 1016 Reverse power inverse %/10 1/10s
3 1020 Overcurrent 1 %/10 1/10s
4 1030 Overcurrent 2 %/10 1/10s
5 1041 Overcurrent inverse 1 value %/10 1/10s
6 1042 Overcurrent inverse 2 values %/10 1/10s
7 1043 Overcurrent inverse 3 values %/10 1/10s
8 1051 Overcurrent inverse 4 values %/10 1/10s
9 1052 Overcurrent inverse 5 values %/10 1/10s
10 1053 Overcurrent inverse 6 values %/10 1/10s
11 1060 Overcurrent inv. relays and enable - -
12 1070 Fast overcurr. %/10 1/10s
13 1080 High overcurr. %/10 1/10s
14 Reserved
15 1100 DG high volt 1 %/10 1/10s
16 1110 DG high volt 2 %/10 1/10s
17 1120 DG low volt 1 %/10 1/10s
18 1130 DG low volt 2 %/10 1/10s
19 1140 DG high freq 1 %/10 1/10s
20 1150 DG high freq 2 %/10 1/10s
21 1160 DG low freq 1 %/10 1/10s
22 1170 DG low freq 2 %/10 1/10s
23 1180 U-BB high step 1 %/10 1/100s
24 1190 U-BB high step 2 %/10 1/100s
25 1200 U-BB low step 1 %/10 1/100s
26 1210 U-BB low step 2 %/10 1/100s
27 1220 f-BB high step 1 %/10 1/100s
28 1230 f-BB high step 2 %/10 1/100s
29 1240 f-BB low step 1 %/10 1/100s
30 1250 f-BB low step 2 %/10 1/100s
31 1260 Overload 1 %/10 1/10s
32 1270 Overload 2 %/10 1/10s
33 1280 Unbalance curr. %/10 1/10s
34 1290 Unbalance volt. %/10 1/10s
35 1300 var import %/10 1/10s
36 1310 var export %/10 1/10s
37 1320 Gen. neg. sequence current %/10 1/10s
38 1330 Gen. neg. sequence voltage %/10 1/10s
39 Reserved
40 1350 df/dt (ROCOF) Hz/10/s n
41 1352 df/dt (ROCOF) measuring time Periods n
42 1360 Vector jump Deg./10 n

DEIF A/S Page 18 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

Offset Ch. no. Content Value Delay

address unit unit
43-44 Reserved
nd
45 1410 Reverse power S2 (2 param. set) %/10 1/10s
nd
46 1420 Overcurrent 1 S2 (2 param. set) %/10 1/10s
nd
47 1430 Overcurrent 2 S2 (2 param. set) %/10 1/10s
nd
48 1440 DG high volt 1 S2 (2 param. set) %/10 1/10s
nd
49 1450 DG high volt 2 S2 (2 param. set) %/10 1/10s
nd
50 1460 DG low volt 1 S2 (2 param. set) %/10 1/10s
nd
51 1470 DG low volt 2 S2 (2 param. set) %/10 1/10s
nd
52 1480 DG high freq 1 S2 (2 param. set) %/10 1/10s
nd
53 1490 DG high freq 2 S2 (2 param. set) %/10 1/10s
nd
54 1500 DG low freq 1 S2 (2 param. set) %/10 1/10s
nd
55 1510 DG low freq 2 S2 (2 param. set) %/10 1/10s
nd
56 1520 U-BB high step 1 S2 (2 param. set) %/10 1/100s
nd
57 1530 U-BB high step 2 S2 (2 param. set) %/10 1/100s
nd
58 1540 U-BB low step 1 S2 (2 param. set) %/10 1/100s
nd
59 1550 U-BB low step 2 S2 (2 param. set) %/10 1/100s
nd
60 1560 f-BB high step 1 S2 (2 param. set) %/10 1/100s
nd
61 1570 f-BB high step 2 S2 (2 param. set) %/10 1/100s
nd
62 1580 f-BB low step 1 S2 (2 param. set) %/10 1/100s
nd
63 1590 f-BB low step 2 S2 (2 param. set) %/10 1/100s
nd
64 1600 Overload 1 S2 (2 param. set) %/10 1/10s
nd
65 1610 Overload 2 S2 (2 param. set) %/10 1/10s
nd
66 1620 Unbalance curr. S2 (2 param. set) %/10 1/10s
nd
67 1630 Unbalance volt. S2 (2 param. set) %/10 1/10s
nd
68 1640 var import S2 (2 param. set) %/10 1/10s
nd
69 1650 var export S2 (2 param. set) %/10 1/10s
70 2011 Static sync. (enable/disable only)
71 2021 Sync. df max. Hz/10 n
72 2022 Sync. df min. Hz/10 n
73 2023 Sync. DU max. % n
74 2024 Sync. t CB ms n
75 2031 Static sync. df max. Hz/10 n
76 2032 Static sync. dU max. % n
77 2033 Static close window Deg. n
78 2034 Static phase controller Kp None n
79 2035 Static phase controller Ki None n
80 2041 Blackout df max. Hz/10 n
81 2042 Blackout dU max. % n
82 2043 Blackout enable n n
83 2050 Sync. window % 1/10s
84 2060 Sync. failure n 1/10s
85 2070 General failure n 1/10s
86 Reserved
87 Reserved
88 Reserved
89 Reserved
90 2110 Modes active n n
91 2121 Freq. control DB %/10 n

DEIF A/S Page 19 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

Offset Ch. no. Content Value Delay

address unit unit
92 2122 Freq. control Kp None n
93 2123 Freq. control Ki None n
94 2124 Freq. control droop %/10 n
95 2131 Power control DB %/10 n
96 2132 Power control Kp None n
97 2133 Power control Ki None n
98 2141 Power ramp up speed %/10/s n
99 2142 Power ramp up point % n
100 2151 Power ramp down speed %/10/s n
101 2152 Power ramp down point % n
102 2160 Analogue governor offset % n
103 Reserved
104 Reserved
105 Reserved
106 2180 Governor regulator failure % 1/10s
107 2191 Volt. control DB %/10 n
108 2192 Volt. control Kp None n
109 2193 Volt. control Ki None n
110 2201 var control DB %/10 n
111 2202 var control Kp None n
112 2203 var control Ki None n
113 2210 Analogue AVR offset % n
114 Reserved
115 Reserved
116 Reserved
117 2230 AVR regulator fail. n 1/10s
118 Reserved
119 Reserved
120 Reserved
121 2251 GOV min. ON time ms n
122 2252 GOV period time ms n
123 2253 AVR min. ON time ms n
124 2254 AVR period time ms n
125 2260 GOV/AVR setup (outputs) None n
126 2271 Minimum value (PWM) % n
127 2272 Initial value (PWM) % n
128 2273 Maximum value (PWM) % n
129 2274 Enable PWM None n
130 2281 Water control DB % n
131 2282 Water control Kp None n
132 2283 Water control Ki None n
133 3440 4-20mA in no. 1 (alarm setting) User y
134 3460 4-20mA in no. 2 (alarm setting) User y
135 3480 4-20mA in no. 3 (alarm setting) User y
136 3500 4-20mA in no. 4 (alarm setting) User y
137 3520 4-20mA in no. 5 (alarm setting) User y
138 3540 4-20mA in no. 6 (alarm setting) User y
139 3560 4-20mA in no. 7 (alarm setting) User y

DEIF A/S Page 20 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

Offset Ch. no. Content Value Delay

address unit unit
140 3580 4-20mA in no. 8 (alarm setting) User y
141 3600 PT100 no. 1 Deg. y
142 3620 PT100 no. 2 Deg. y
143 3640 Overspeed (Tacho) RPM y
144 3120 Dig. input term. 23 None y
145 3130 Dig. input term. 24 None y
146 3140 Dig. input term. 25 None y
147 3150 Dig. input term. 26 None y
148 3160 Dig. input term. 27 None y
149 3170 Dig. input term. 43 None y
150 3180 Dig. input term. 44 None y
151 3190 Dig. input term. 45 None y
152 3200 Dig. input term. 46 None y
153 3210 Dig. input term. 47 None y
154 3220 Dig. input term. 48 None y
155 3230 Dig. input term. 49 None y
156 3240 Dig. input term. 50 None y
157 3250 Dig. input term. 51 None y
158 3260 Dig. input term. 52 None y
159 3260 Dig. input term. 53 None y
160 3270 Dig. input term. 110 None y
161 3280 Dig. input term. 111 None y
162 3290 Dig. input term. 112 None y
163 3300 Dig. input term. 113 None y
164 3310 Dig. input term. 114 None y
165 3320 Dig. input term. 115 None y
166 3330 Dig. input term. 116 None y
167 3340 Dig. input term. 117 None y
168 3350 Dig. input term. 118 None y
169 3360 Dig. input term. 127 None y
170 3370 Dig. input term. 128 None y
171 3380 Dig. input term. 129 None y
172 3390 Dig. input term. 130 None y
173 3400 Dig. input term. 131 None y
174 3410 Dig. input term. 132 None y
175 3420 Dig. input term. 133 None y
176 3660 Oil pressure (VDO 1) % 1/10s
177 3666 VDO 1 type None n
178 3680 Cool water temp. (VDO 2) % 1/10s
179 3686 VDO 2 type None n
180 3700 Fuel level (VDO 3) % 1/10s
181 3706 VDO 3 type None n
182 4011 Nom. frequency Hz/10 n
183 4012 Nom. power kW n
184 4013 Nom. current A n
185 4014 Nom. voltage V n
186 4021 Volt prim. GEN V n
187 4022 Volt sec. GEN V n

DEIF A/S Page 21 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

Offset Ch. no. Content Value Delay

address unit unit
188 4023 Current prim. A n
189 4024 Current sec. A n
190 4031 Volt prim. BUS V n
191 4032 Volt sec. BUS V n
192 4041 Control settings P % n
193 4042 Control settings var % n
194 4043 Control settings PF None n
195 4044 Control settings water level % n
196 4051 Comm. bus control P n0 n
197 4052 Comm. bus control f n0 n
198 4053 Comm. bus control U n0 n
199 4054 Comm. bus control Q n0 n
200 4055 Comm. bus control PF n0 n
201 4061 Ext. comm. ID None n
202 4062 Baud rate 0=9600, 1=19200 None n
203 4092 Ext. comm. error n1 1/10s
204 4121 Running time n0 n
205 4122 Circuit breaker operations n0 n
206 4123 Reset kWh counter n0 n
207 4133 Water level control ON/OFF n0 n
208 4220 Battery low V V/10 1/10s
209 4231 Language None n
210 4240 Loadshare out 1/10V n
211 4250 Loadshare type None n
212 4260 Start next gen. % 1/10s
213 4270 Stop next gen. % 1/10s
214 4351 Running RPM RPM n
215 4352 No. of teeth (flywheel) None n
216 4361 Start prepare n 1/10s
217 4362 Start ON time (crank) n 1/10s
218 4363 Start OFF time (pause) n 1/10s
219 4371 Start attempts None n
220 4381 f/U OK n 1/10s
221 4391 f/U failure n 1/10s
222 4401 Cooldown time n 1/10s
223 4402 Extended stop time (stop coil) n 1/10s
224 4403 Coil type None n
225 4410 Stop failure n 1/10s
226 4420 Run status b 1/10s
227 Reserved
228 Reserved
229 Reserved
230 4502 P output type 0 or 4 n
231 4512 S output type 0 or 4 n
232 4522 Q output type 0 or 4 n
233 4532 PF output type 0 or 4 n
234 4542 f output type 0 or 4 n
235 4552 U output type 0 or 4 n

DEIF A/S Page 22 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

Offset Ch. no. Content Value Delay

address unit unit
236 4562 I output type 0 or 4 n
237 4503 P output max. kW n
238 4513 S output max. kVA n
239 4523 Q output max. var n
240 4533 PF output max. None n
241 4543 f output max. Hz/10 n
242 4553 U output max. V n
243 4563 I output max. A n
244 4504 P output min. kW n
245 4514 S output min. kVA n
246 4524 Q output min. kvar n
247 4534 PF output min. None n
248 4544 f output min. Hz/10 n
249 4554 U output min. V n
250 4564 I output min. A n
251 4600 Relay 0 virtual None 1/10s
252 4610 Relay 1 None 1/10s
253 4620 Relay 2 None 1/10s
254 4630 Relay 3 None 1/10s
255 4640 Relay 4 None 1/10s
256 4650 Relay 5 None 1/10s
257 4660 Relay 6 None 1/10s
258 4670 Relay 7 None 1/10s
259 4680 Relay 8 None 1/10s
260 4690 Relay 9 None 1/10s
261 4700 Relay 10 None 1/10s
262 4710 Relay 11 None 1/10s
263 4720 Relay 12 None 1/10s
264 4730 Relay 13 None 1/10s
265 Reserved
266 Reserved
267 Reserved
268 4771 CCM baud rate None n
269 4781 MID/UNIT number None n
270 4791 MID/UNIT number None n
271 4801 MID/UNIT number None n
272 4811 MID/UNIT number None n
273 4821 MID/UNIT number None n
274 4831 MID/UNIT number None n
275 4841 MID/UNIT number None n
276 4851 MID/UNIT number None n
277 4861 MID/UNIT number None n
278 4871 MID/UNIT number None n
279 4881 MID/UNIT number None n
280 4891 MID/UNIT number None n
281 4901 MID/UNIT number None n
282 4911 MID/UNIT number None n
283 4321 MID/UNIT number None n

DEIF A/S Page 23 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

Offset Ch. no. Content Value Delay

address unit unit
284 4931 MID/UNIT number None n
285 4762 Enable list 1 n0 n
286 4772 Enable list 2 n0 n
287 4782 Enable list 3 n0 n
288 4792 Enable list 4 n0 n
289 4802 Enable list 5 n0 n
290 4812 Enable list 6 n0 n
291 4822 Enable list 7 n0 n
292 4832 Enable list 8 n0 n
293 4842 Enable list 9 n0 n
294 4852 Enable list 10 n0 n
295 4862 Enable list 11 n0 n
296 4872 Enable list 12 n0 n
297 4882 Enable list 13 n0 n
298 4892 Enable list 14 n0 n
299 4902 Enable list 15 n0 n
300 4912 Enable list 16 n0 n
301 4763 Update rate 1/10s n
302 4773 Update rate 1/10s n
303 4783 Update rate 1/10s n
304 4793 Update rate 1/10s n
305 4803 Update rate 1/10s n
306 4813 Update rate 1/10s n
307 4823 Update rate 1/10s n
308 4833 Update rate 1/10s n
309 4843 Update rate 1/10s n
310 4853 Update rate 1/10s n
311 4863 Update rate 1/10s n
312 4873 Update rate 1/10s n
313 4883 Update rate 1/10s n
314 4893 Update rate 1/10s n
315 4903 Update rate 1/10s n
316 4913 Update rate 1/10s n
317 4971 Password None n
318 Reserved
319 5011 VDO 1 at 0.0 Bar Ohm/10 n
320 5012 VDO 1 at 2.5 Bar Ohm/10 n
321 5013 VDO 1 at 5.0 Bar Ohm/10 n
322 5014 VDO 1 at 6.0 Bar Ohm/10 n
323 5021 VDO 1 at 7.0 Bar Ohm/10 n
324 5022 VDO 1 at 8.0 Bar Ohm/10 n
325 5023 VDO 1 at 9.0 Bar Ohm/10 n
326 5024 VDO 1 at 10.0 Bar Ohm/10 n
o
327 5031 VDO 2 at 40 C Ohm n
o
328 5032 VDO 2 at 50 C Ohm n
o
329 5033 VDO 2 at 60 C Ohm n
o
330 5034 VDO 2 at 70 C Ohm n
o
331 5041 VDO 2 at 80 C Ohm n

DEIF A/S Page 24 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

Offset Ch. no. Content Value Delay

address unit unit
o
332 5042 VDO 2 at 90 C Ohm n
o
333 5043 VDO 2 at 100 C Ohm n
o
334 5044 VDO 2 at 110 C Ohm n
335 5051 VDO 3 at 0% Ohm/10 n
336 5052 VDO 3 at 40% Ohm/10 n
337 5053 VDO 3 at 50% Ohm/10 n
338 5054 VDO 3 at 60% Ohm/10 n
339 5061 VDO 3 at 70% Ohm/10 n
340 5062 VDO 3 at 80% Ohm/10 n
341 5063 VDO 3 at 90% Ohm/10 n
342 5064 VDO 3 at 100% Ohm/10 n
343 4070 CAN bus off n n
344 4080 CAN bus transmit fail. n n
345 2275 PWM control droop %/10 n
346 4941 Asynchronous synchronisation n n
347 4942 Slip frequency %/10 n
348 4952 Inverted reg. n n
349 4951 No. of valves None n
350 4353 Nominal RPM RPM n
351 4045 Water minimum % n
352 4960 Voltage trip type None n
353 Reserved
354 3450 4-20 mA input no. 1 (alarm setting 2) User n
355 3470 4-20 mA input no. 2 (alarm setting 2) User n
356 3490 4-20 mA input no. 3 (alarm setting 2) User n
357 3510 4-20 mA input no. 4 (alarm setting 2) User n
358 3530 4-20 mA input no. 5 (alarm setting 2) User n
359 3550 4-20 mA input no. 6 (alarm setting 2) User n
360 3570 4-20 mA input no. 7 (alarm setting 2) User n
361 3590 4-20 mA input no. 8 (alarm setting 2) User n
362 3610 Pt100 no. 1 (alarm setting 2) Deg. y
363 3630 Pt100 no. 2 (alarm setting 2) Deg. y
364 3650 Overspeed (tacho alarm setting 2) RPM y
365 3670 Oil pressure (VDO1, alarm setting 2) % 1/10s
366 3690 Cool w. temp. (VDO 2, al. setting 2) % 1/10s
367 3710 Fuel level (VDO 3, alarm setting 2) % 1/10s
368 4063 Comm. mode (0: RTU, 1: ASCII) None n
369 Reserved
370 Reserved
371 Reserved
372 Reserved
373 Reserved
374 5116 Pincode GSM None n
375 5201 MID/UNIT number, SPR 1 None n
376 5211 MID/UNIT number, SPR 2 None n
377 5221 MID/UNIT number, SPR 3 None n
378 5231 MID/UNIT number, SPR 4 None n
379 5241 MID/UNIT number, SPR 5 None n

DEIF A/S Page 25 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

Offset Ch. no. Content Value Delay

address unit unit
380 5251 MID/UNIT number, SPR 6 None n
381 5261 MID/UNIT number, SPR 7 None n
382 5271 MID/UNIT number, SPR 8 None n
383 5281 MID/UNIT number, SPR 9 None n
384 5291 MID/UNIT number, SPR 10 None n
385 5202 Enable single parameter read 1 None n
386 5212 Enable single parameter read 2 None n
387 5222 Enable single parameter read 3 None n
388 5223 Enable single parameter read 4 None n
389 5242 Enable single parameter read 5 None n
390 5252 Enable single parameter read 6 None n
391 5262 Enable single parameter read 7 None n
392 5272 Enable single parameter read 8 None n
393 5282 Enable single parameter read 9 None n
394 5292 Enable single parameter read 10 None n
395 5203 Update rate SPR 1 1/10s n
396 5213 Update rate SPR 2 1/10s n
397 5223 Update rate SPR 3 1/10s n
398 5233 Update rate SPR 4 1/10s n
399 5243 Update rate SPR 5 1/10s n
400 5253 Update rate SPR 6 1/10s n
401 5263 Update rate SPR 7 1/10s n
402 5273 Update rate SPR 8 1/10s n
403 5283 Update rate SPR 9 1/10s n
404 5293 Update rate SPR 10 1/10s n
405 4771 CAN engine interface type None n
406 4771 Cummins engine interface type None n
407 4781 EIC unit None n
408 4790 EI communication error n 1/10s
409 4800 EIC warning n 1/10s
410 4810 EIC shutdown n 1/10s
411 4820 EIC overspeed RPM 1/10s
412 4830 EIC coolant temp. (alarm setting 1) Deg. 1/10s
413 4840 EIC coolant temp. (alarm setting 2) Deg. 1/10s
414 4850 EIC oil pressure (alarm setting 1) 1/10bar 1/10s
415 4860 EIC oil pressure (alarm setting 2) 1/10bar 1/10s

Refer to the Designer’s Reference Handbook of your multi-line for information on:

• Availability of channels
• Min./max. settings
• Factory settings

Note that several channels also depend on the options.

However, it is possible to write to channels where the option is not set, it is not possible to enable
the channel. E.g. if an attempt is made to write a "1" to the enable flag, the "1" will be discarded,
and the enable flag remains "0". It is not possible to write to offset 0. These values are used for
DEIF internal version control.

DEIF A/S Page 26 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

"y" means that the channel is writeable.

"n" means that a "0" can be written to the channel only.
"n10" means that only the value 10 can be written.

Examples:
• Write nominal frequency (4011), offset 182, 60Hz
ID = 1, 60Hz = 600Hz/10 = 0258h
Address 2000 + 182 = 2182d = 0886h
Tx: 01h 10h 08h 86h 00h 01h 02h 58h 30h ACh
Rx: 01h 10h 08h 86h 00h 01h E2h 40h

• Read nominal frequency (4011) offset 182, 60Hz

Tx: 01h 03h 08h 86h 00h 01h 67h 83h
Rx: 01h 03h 02h 02h 58h B8h DEh
Read 0258h = 600d

DEIF A/S Page 27 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

Digital input table (read only 01h)

Address Terminal Description

1500 - Not used
1501 127 Binary input (option M13)
1502 128 Binary input (option M13)
1503 129 Binary input (option M13)
1504 130 Binary input (option M13)
1505 131 Binary input (option M13)
1506 132 Binary input (option M13)
1507 133 Binary input (option M13)
1508-1528 - Reserved
1529 43 De-load
1530 44 Man. governor up
1531 45 Man. governor down
1532 46 Man. AVR up
1533 47 Man. AVR down
1534 48 Mode 1
1535 49 Mode 2
1536 50 Mode 3
1537 51 Mode 4
1538 52 Mode 5
1539 53 Mode 6
1540 54 Breaker position off
1541 55 Breaker position on
1542 23 Alarm inhibit
1543 24 Alarm acknowledge
1544 25 Sync. start
1545 26 Control via external communication
1546 27 Block loss of mains
1546-1574 Reserved
1575 110 Binary input option M2
1576 111 Binary input option M2
1577 112 Binary input option M2
1578 113 Binary input option M2
1579 114 Binary input option M2
1580 115 Binary input option M2
1581 116 Binary input option M2
1582 117 Binary input option M2
1583 118 Binary input option M2

DEIF A/S Page 28 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

Digital output table (read only 01h)

Address Terminal Description

2000 69/70 AVR up
2001 71/72 AVR down
2002 65/66 Governor up
2003 67/68 Governor down
2004 126/127 Relay 10
2005 128/129 Relay 11
2006 130/131 Relay 12
2007 132/133 Relay 13
2008 - 2015 - Not used
2016 57/58 Relay 5
2017 59/60 Relay 6
2018 61/62 Relay 7
2019 63/64 Relay 8
2020 - Not used
2021 - Not used
2022 - Not used
2023 - Not used
2024 - Not used
2025 5/6 Relay 1
2026 8/9 Relay 2
2027 11/12 Relay 3
2028 14/15 Relay 4
2029 17/18 Sync. relay (on in short time)
2030-2043 Reserved
2044 120/121 Start (engine)
2045 122/123 Stop (engine) (relay 9)
2046 124/125 Start prepare (engine)

DEIF A/S Page 29 of 30

PPU/GPC/GPU Option H2, RS 485 Modbus communication

6. Technical data

Operating temperature: -25…70°C

Aux. supply: Internal from the multi-line unit

Galvanic separation: Between AC voltage, AC current and other I/Os:

3250 VAC – 50 Hz – 1 min.
Between analogue outputs:
500 VDC – 1 min.

EMC/CE: According to EN-50081-1/2, EN-50082-1/2, SS4361503 (PL4) and

IEC 255-3

Material: All plastic parts are self-extinguishing to UL94 (V1)

Climate: HSE, to DIN 40040

2
Connections: 2.5 mm multi stranded

Modbus data: RTU mode:

• 9600 or 19200 bps
• 8 data bits
• None parity
• 1 stop bit

ASCII mode:
• 9600 or 19200 bps
• 7 data bits
• None parity
• 1 stop bit

For further technical data, please refer to the Designer’s Reference Handbook.

DEIF A/S reserves the right to change any of the above

DEIF A/S Page 30 of 30