Scribd Logo
Upload

Welcome to Scribd!

  • 9 views

    Torque de Mancal Fixo 3512C.

    Uploaded by

    ivissonbbb22
    3512

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Torque de Mancal Fixo 3512C.

    Uploaded by

    ivissonbbb22
    9 views5 pages
    3512

    Original Title

    Torque de Mancal fixo 3512C.

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    3512

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    9 views5 pages

    Torque de Mancal Fixo 3512C.

    Uploaded by

    ivissonbbb22
    3512

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 5

    3512C Marine Auxiliary SLM00001-UP(SEBP4539 - 52) - Documentation Page 1 of 5

    Shutdown SIS

    Previous Screen

    Product: MARINE AUXILIARY


    Model: 3512C MARINE AUXILIARY SLM
    Configuration: 3512C Marine Auxiliary SLM00001-UP

    Disassembly and Assembly


    3508C, 3512C and 3516C Marine Engines
    Media Number -KENR6055-14 Publication Date -01/03/2015 Date Updated -04/12/2019

    i07047070

    Crankshaft Main Bearings - Install


    SMCS - 1203-012

    Installation Procedure
    Table 1
    Required Tools
    Tool Part Number Part Description Qty
    A 9S-9082 Engine Turning Tool 1
    B 9U-5023 Main Bearing Wrench 1
    C 2P-5517 Main Bearing Tool 1
    D 236-6688 Main Bearing Cap Tool 2
    E 9S-7351 Torque Wrench 1
    F 8T-5096 Dial Indicator Gp 1

    NOTICE

    Keep all parts clean from contaminants.

    Contaminants may cause rapid wear and shortened component life.

    Note: Install the main bearings dry when clearance checks are preformed. Refer to
    Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the
    main bearings for final assembly.
    3512C Marine Auxiliary SLM00001-UP(SEBP4539 - 52) - Documentation Page 2 of 5

    Illustration 1 g01125211

    1. Install lower main bearing (4) in main bearing cap (2). Ensure that the main bearing is
    installed so that the bearing tab fits into the notch in the main bearing cap.

    Note: The main bearing caps must be installed with the word "FRONT" and the part
    number toward the front of the engine. Each main bearing cap has a number on the bottom
    surface and each main bearing must be installed in the corresponding position in the
    cylinder block.

    2. Install the upper main bearing with the side without the tab into the side of the cylinder
    block with the tab. Use your hand and roll the upper main bearing into position. Use
    Tooling (A) and rotate the crankshaft. Rotate the crankshaft until the oil hole is positioned
    in front of the side of the upper main bearing with the tab.

    Illustration 2 g01125209

    3. Install Tooling (C) and finish rolling the upper main bearing into position. Make sure that
    Tooling (C) does not slide under the upper main bearing. Ensure that the main bearing is
    installed so that the bearing tab fits into the notch in the cylinder block.

    4. Remove Tooling (C).

    5. The following step is for installing the thrust plates on each side of the center main bearing.
    Place clean engine oil on the thrust plates. Install the thrust plates on each side of the center
    main bearing. It may be necessary to move the crankshaft with a prybar in order to install a
    new thrust bearing. Use Tooling (F) to measure the end play of the crankshaft. The end play
    must not exceed 0.17 to 0.63 mm (0.007 to 0.025 inch).
    3512C Marine Auxiliary SLM00001-UP(SEBP4539 - 52) - Documentation Page 3 of 5

    Illustration 3 g01125192

    6. Tighten the nuts on Tooling (D) in order to raise main bearing cap (2) to the cylinder block.
    The nuts must be tightened evenly in order for main bearing cap (2) to fit into the block.

    7. Coat the underside of the bolt heads and the threads of bolts (3) with clean engine oil. Install
    the inner bolts for the main bearing cap. Remove Tooling (D) and install the outer bolts for
    the main bearing cap.

    Illustration 4 g01139473
    3512C Marine Auxiliary SLM00001-UP(SEBP4539 - 52) - Documentation Page 4 of 5

    Illustration 5 g01124192
    Bolt tightening sequence for the main bearing caps

    8. Use Tooling (E) and Tooling (B) and tighten bolts (3) in sequence to a torque of
    190 ± 14 N·m (140 ± 10 lb ft).

    9. Place an index mark on the bolts and the main bearing cap. Tighten the bolts for an
    additional 180 ± 5 degrees (1/2 turn).

    10. Rotate the crankshaft in order to ensure that the crankshaft turns freely.

    Illustration 6 g01125228

    11. Install side covers (1) onto the cylinder block.

    End By:
    3512C Marine Auxiliary SLM00001-UP(SEBP4539 - 52) - Documentation Page 5 of 5

    a. Install the oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".

    Copyright 1993 - 2024 Caterpillar Inc. Tue Mar 12 23:30:25 UTC-0300 2024
    All Rights Reserved.
    Private Network For SIS Licensees.

    You might also like