Specifications
Specifications
Specifications
Specifications
Sealers
Lubricants
Description Specification
Engine oil, SAE 5W-30 Use 5W/30 oil to specification WSS-M2C-913B meeting ACEA B1/B3
Dimensions
Item Specification
Length 523 mm (20·59 in)
Width 717 mm (28·25 in)
Height 771 mm (30·35 in)
General Specifications
Item Specification
2.7 litre, 60 degree 'V', common rail direct injection, turbocharged and intercooled diesel, twin
Type
overhead camshafts, 4 valves per cylinder
Cylinder
V6, numbers 1 and 4 cylinders at front of engine when engine is viewed from rear
arrangement
Cylinder
Number 1 cylinder - right hand bank; Number 4 cylinder - left hand bank
numbering
Bore - nominal 81·0 mm (3·188 in)
Stroke 88·0 mm (3·464 in)
Capacity 2720 cm³ (165·9 in³)
Firing order 1-4-2-5-3-6
Compression ratio 17.3:1
Direction of
Anti-clockwise viewed from rear of engine
rotation
https://myvpn.dealerconnection.com/extdealerlrprod/xml/parsexml.jsp,DanaInfo=gtr.fran... 10/24/2005
Contents Page Page 2 of 4
Torque Specifications
Description Nm lb-ft
Accessory drive belt idler retaining bolt 47 35
Accessory drive belt tensioner M8 retaining bolts 47 35
Accessory drive belt tensioner M10 retaining bolts 25 18
Air conditioning (A/C) compressor retaining bolts 23 17
A/C compressor mounting bracket retaining bolts 23 17
A/C compressor low pressure pipe fixing 9 7
A/C manifold retaining bolt 20 15
Battery positive cable mounting bolts 10 7
* Camshaft inner bearing cap retaining bolts
Stage 1: tighten bolts 1 to 14 1 1
Stage 2: tighten bolts 1 to 14 5 4
Stage 3: tighten bolts 1 to 14 10 7
* Camshaft outer bearing cap retaining bolts
Stage 1: tighten bolts 1 to 4 1 1
Stage 2: tighten bolts 1 to 4 5 4
Stage 3: tighten bolts 1 to 4 10 7
Camshaft position sensor retaining bolt 10 7
+¹ Camshaft hub retaining bolts
Stage 1 80 59
Stage 2 Further 90° Further 90°
Camshaft pulley retaining bolts 23 17
Camshaft timing belt cover securing bolts 10 7
+² Crankshaft pulley retaining bolt
Stage 1 100 74
Stage 2 Further 90° Further 90°
Crankshaft damper bolts 14 10
Crankshaft position sensor retaining bolt 5 4
Crankshaft rear seal retainer plate 10 7
Coolant outlet elbow 10 7
*+² Cylinder head retaining bolts
Stage 1 20 15
Stage 2 40 30
Stage 3 80 59
Stage 4 Further 180° Further 180°
Differential front mounting bracket heat shield 10 7
EGR valve inlet tube 10 7
EGR valve mounting bolts 10 7
https://myvpn.dealerconnection.com/extdealerlrprod/xml/parsexml.jsp,DanaInfo=gtr.fran... 10/24/2005
Contents Page Page 3 of 4
https://myvpn.dealerconnection.com/extdealerlrprod/xml/parsexml.jsp,DanaInfo=gtr.fran... 10/24/2005
Contents Page Page 4 of 4
* Bolts must be tightened in sequence + New bolts must be installed ¹ Lightly oil bolt threads ² Do not apply lubricant to
bolt threads
https://myvpn.dealerconnection.com/extdealerlrprod/xml/parsexml.jsp,DanaInfo=gtr.fran... 10/24/2005