Scribd Logo
Upload

Welcome to Scribd!

  • 12 views

    Dtsu666 User Manual en - Part1

    Uploaded by

    brobata
    SOLAR

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Dtsu666 User Manual en - Part1

    Uploaded by

    brobata
    12 views2 pages
    SOLAR

    Original Title

    dtsu666-user-manual-en_Part1

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    SOLAR

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    12 views2 pages

    Dtsu666 User Manual en - Part1

    Uploaded by

    brobata
    SOLAR

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    DTSU666 and DTSU666-CT three phase Smart meter

    ZTY0.464.1267
    (Din-rail)
    Operation manual Page 8, Total 18

    5: Odd parity, 1 stop bit, O.1;


    Communication baud rate：
    0：1.200；
    0：1200 bps；
    1：2.400；
    1：2400 bps；
    2：4.800；
    2：4800 bps；
    3：9.600；
    3：9600 bps；
    1～247 Communication address
    Option for wiring mode:
    0：n.34；
    0：n.34 represents three phase four wire;
    1：n.33；
    1：n.33 represents three phase three wire.
    The setting is 1, representing the allowed instrument energy data clearance,
    0:no；1:E
    which will be zero reset after clearing.
    0:P；1:Q； Pulse output:
    2:S； 0：actsive energy pulse; 1: reactive energy pulse; 2：Others.
    Display in turns(second)
    0～30
    0：Timely display； 1～30：Time interval of actual display.
    4.2.2. Programming operation

    Button description: “SET” button represents “confirmation”, or “cursor shift” (when input digits),

    “ESC” button represents “exit”, “→” button represents “add”. The input code is (default 701).

    Figure 3 Setting examples for current and potential transformer ratio


    DTSU666 and DTSU666-CT three phase Smart meter
    ZTY0.464.1267
    (Din-rail)
    Operation manual Page 9, Total 18

    Figure 4 Setting examples for communication address and Baud Rate


    When input digits, “SET” can be used as cursor “_”motion button; “→”is “add” button, “ESC

    ”is Exit the programming operation interface or switch to the character interface from digit modification

    interface, add from the beginning after setting the digit to the maximum value.

    4.3. Communication function

    Characterized with a RS485 communication interface, the baud rate can be changed between

    1200bps, 2400bps, 4800bps and 9600bps.

    Factory default communication parameter is ModBus-RTU protocol, the baud rate is 9600bps,

    with the calibration bit and stop bit to be n.1, and the instrument address to be 1. The following table

    is the common ModBus protocol address table, can be asked for specified communication protocol

    by calling. ModBus_RTU protocol read command is 03H, write command is 10H.

    Table 10 ModBus protocol address table


    Data
    Parameter Parameter Read
    Instructions of parameters Data type length
    address code Write
    Word
    Keyboard parameters (specific parameters see the instructions of programming parameters, the actual value
    with (*) parameter＝ communication parameter value × 0.1）
    0000H REV. Software Version Signed 1 R
    0001H UCode Programming code codE(1～9999) Signed 1 R/W
    0002H ClrE Power reset CLr.E(1:energy clear) Signed 1 R/W
    0003H Network selection (0:three phase four Signed 1 R/W

    You might also like