Acer Al1715p SM

Acer AL1715p Service Guide
Service guide files and updates are available on the CSD web: for more information, Please refer to http://csd.acer.com.tw/
Acer AL1715p is existing model (AL1715) with AU and Samsung panel. PM changed the product name for project control. The only difference on Acer AL1715 and Acer AL1715p is that the later employs AUO and Samsung panel.
-1-
Copyright
Copyright 2003 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice. Acer Incorporated makes no representations or warranties, either expresses or implied, with respect to the contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular purpose, Any Acer Incorporated software described in this manual is sold or licensed as is . Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, of its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation. Intel is a registered trademark of Intel Corporation. Pentium and Pentium II/III are trademarks of Intel Corporation. Other brand and product names are trademarks and/or registered trademarks of their respective holders.
-2-
Conventions
The following conventions are used in this manual: Screen messages Note Warning Caution Important Denotes actual messages that appear on screen Gives bits and pieces of additional information related to the current topic. Alerts you to any damage that might result from doing or not doing specific actions. Gives precautionary measures to avoid possible hardware or software problems. Reminds you to do specific actions relevant to the accomplishment of procedures.
Preface
Before using this information and the product it supports, please read the following general information. 1. this Service Guide provides you with all technical information relating to the BASICCONFIGURATION decided for Acers global product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such cases, please contact your regional offices or the responsible personnel/channel to provide you with further technical details. 2. please not WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on your regional web or channel. If, for whatever reason, a part number change is made, it will not be noted in the printed Service Guide, for ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and Service of customer machines.
-3-
WARNING: (FOR FCC CERTIFIED MODELS)

NOTE: this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, Which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help.
Warning
Use only shielded signal cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the party responsible for comliance could viold your authority to operate the equipment. As an ENERGY STAR Partner our company has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

WARNING:
To prevent fire or chock hazard, do not expose the monitor to rain or moisture. Dangerously high voltages are present inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only.
-4-
PRECAUTIONS
Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, Swimming pool or in a wet basement. Do not place the monitor on an unstable trolley, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a trolley or stand recommended by the manufacture or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacture and follow the kit instructions. Slots and openings in the back and bottom of the cabinet area provided for ventilation. To ensure reliable operation of the monitor and to protect it from overheating, be sure these openings are not blocked or covered. Do not place the monitor on a bed, sofa, rug or similar surface. Do not place the monitor near or over a radiator or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided. The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug. Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor from damage due to power surges. Do not overload power strips and extension cords. Overloading can result in fire or electric shock. Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric shock. Never spill liquids on the monitor. Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous voltages and other hazards. Please refer all servicing to qualified service personnel. To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100-240V AC, Min. 3.5A. The wall socket shall be installed near the equipment and shall be easily accessible.
-5-
SPECIAL NOTES ON LCD MONITORS

The following symptoms are normal with LCD monitor and do not indicate a problem.
NOTES
Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. You may find slightly uneven brightness in the screen depending on the desktop pattern you use. The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or less such as a missing pixel or a pixel lit all of the time. Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image, when the same image is displayed for hours. In this case, the screen is recovered slowly by changing the image or turning off the Power Switch for hours.
-6-
Table of contents
Chapter 1 Monitor Feature .....8 Chapter 2 Operating Instruction ....22 Chapter 3 Machine Disassembly and Replacement ..30 Chapter 4 Troubleshooting ..40 Chapter 5 Connector Information ..44 Chapter 6 FRU List 45 Chapter 7 Schematic Diagram ...65
-7-
Chapter 1
Monitor Feature
INTRODUCTION
Scope This specification defines the requirements for the 17 MICRO-PROCESSOR based Multi-mode supported high resolution color LCD monitor. This monitor can be directly connected to general 15 pin D-sub VGA connector and eliminates the requirement of optional special display card. It also supports VESA DPMS power management and plug & play function. There is a build-in stereo audio amplifier with volume control to drive a pair of speakers.
Description
The LCD monitor is designed with the latest LCD technology to provide a performance oriented product with no radiation. This will alleviate the growing health concerns. It is also a space saving design, allowing more desktop space, and comparing to the traditional CRT monitor, it consumes less power and gets less weight in addition MTBF target is 20k hours or more.
Comparison Chart of AR577/578 AR577

Normal 17 panel Panel Signal Interface Sync Type for analog input HYDIS HT17E12-200 DSUB Separate / compatible /
AR578
Normal 17 panel HYDIS HT17E12-200 DSUB Separate / compatible /
Support Color Temp user adjust
Support
DDC DDC2B Speaker Headphone Jack Microphone Jack USB Hub Tilt / Swivel Height Adjust 0.5W+0.5W NO No Not support Yes / No Option
-8-
DDC2B NO NO No Not support Yes / No Option
ELECTRICAL REQUIREMENTS
Standard Test Conditions
All tests shall be performed under the following conditions, unless otherwise specified. Ambient light : Viewing distance : Warrn up time All specifications : Fully functional : Measuring Equipment : 30 minutes 5 seconds Chroma 2250 signal generator or equivalent, directly Connected to the monitor under test. Minolta CA100 photometer, or equivalent Control settings User brightness control : User contrast control: User red/white balance, Green/white balance and Blue/white balance control : Power input: Ambient temperature: Analog input mode: In the center (unless otherwise specified ) 110Vac or 230Vac 20 5 C ( 68 9 F) 1280 x1024 /60 Hz Maximum (unless otherwise specified ) Typical (unless otherwise specified ) 225 lux 50 cm in front of LCD panel
MEASUREMENT SYSTEMS
The units of measure stated in this document are listed below: 1 gamma = 1 nano tesla 1 tesla = 10,000 gauss cm = in x 2.54 lb = kg x 2.2 degrees F = [C x 1.8] + 32 degrees C = [F - 32]/1.8 u' = 4x/(-2x + 12y + 3) v' = 9y/(-2x + 12y + 3) x = (27u'/4)/[(9u'/2) - 12v' + 9] y = (3v')/[(9u'/2) - 12v' + 9] nits = cd/(m2) = Ft-L x 3.426 lux = foot-candle x 10.76
-9-
LCD monitor General specification

Panel Type: 17 active matrix color TFT LCD 1). Hydis HT17E12-200
Display size: Display mode:
37.92mm (H) 270.34mm(V) VGA VGA SVGA XGA SXGA 720 640 800 1024 400 480 600 768 (70 Hz) (60/66/70/72/75 Hz) (60/70/72/75 Hz) (60/70/75 Hz)
1280 1024 (60/70/75 Hz) standard resolution
Pixel pitch: Display Dot: Pixel Clock: Contrast ratio: = 0 Brightness: Response time (Tr/Tf): Display color: Viewing angle:
0.264mm(H) 0.264mm(V) 1280 x (RGB) 1024 25.2 135.0MHz HYDIS 430:1 HYDIS:250 HYDIS(20) 16.2M(6 bit color+FRC) HYDIS L / R U / D 80 / 65 / 80 ( 65 ( 160 degrees horizontal typical) 130 degrees vertical typical)
Luminance Uniformity: Pc interface:
> 75 % (typical) 1).Video: RGB analog 0.7V peak to peak Sync: TTL positive or negative
Signal connector:
15 pin Mini D type, (standard VGA video)
3.5 mm stereo audio jack (Audio) (For AR577 only) Audio power: Front control: Interface frequency Horizontal Frequency Vertical Frequency Plug & play: Power Input voltage: 24KHz --80KHz 49Hz ------75Hz Support VESA DDC2B functions Single phase, 50/60HZ, 100 VAC to 240VAC 10% 60 Watt max.
- 10 -
0.5Wrms + 0.5Wrms (300Hz 10kHz (S.P.L. 10 dB))(AR577 only) power on/off with LED select adjustment (+,-)
Total output power:
LCD Panel Specification

LCD Panel Model (Hydis LT17E12-200)
Display Type Resolution Display Dot Display Area Pixel Pitch Display Color Lamp Voltage Lamp Current Weight Optical Specifications
active matrix color TFT LCD 1280x1024 pixels 1280x (RGB) x 1024 337.92mm(H) x 270.34mm(V) 0.264mm(H) x 0.264mm(V) 16M (6 bite color+FRC) 700 Vrms (typ) 6.5 mArms (typ) 1900g (typ)
IL = 6.5mA (RMS) ITEM
Ta = 25 2C Symbol CR
VDD = 5V Condition
FV = 60Hz MIN.
FDCLK = 54MHz TYP. MAX. UNIT
Contrast Ratio (Center of screen) Response Time at Ta Rising Falling
350 TR TF YL =0, RX =0 Normal Viewing Angle 200 0.603 0.324 0.262 0.568 0.115 0.077 0.275 0.308 CR10 -
430 20 -
(total) msec
2
Luminance of white (Center of screen)
250 0.633 0.354 0.292 0.598 0.145 0.107 0.305 0.338 80 80 65 65 -
0.663 0.384 0.322 0.628 0.175 0.137 0.335 0.368 1.2 5 2.0
cd/m
Red Color Chromaticity (CIE) Blue
RY GX
Green
GY BX BY WX
White
WY L R H L BUNI F CT
Viewing Angle
Hori.
Degrees
Vert. Brightness Uniformity Flicker Cross talk
% %
- 11 -
Panel Relative Humidity
Input Signals
Video input

Sync input
Type Input Impedance Polarity Amplitude Display Color
Analog R, G, B. 75 ohm +/- 2% Positive 0 - 0.7 +/- 0.05 Vp same as LCD panel
Signal
separate horizontal and vertical sync, or composite sync which are TTL compatible
Polarity
positive and negative.
Interface frequency The following frequency range is generalized by supported timing. If the entered mode does not match the supported timing the display optimization will not be assured.
Horizontal Frequency Vertical Frequency
24KHz --80KHz 49Hz -------75Hz
- 12 -
Supported Timing
FH(KHZ) TIMING FV(HZ) 640x350 VGA-350 640x400 NEC PC9801 640x400 VGA-GRAPH 640x400 NEC PC9821 640X480 VESA-PAL 640x480 VGA-480 640x480 APPLE MAC-480 640x480 VESA-480-72Hz 640x480 VESA-480-75Hz 720x400 VGA-400-TEXT 832x624 APPLE MAC-800 800x600 SVGA 800x600 VESA-600-60Hz 800x600 VESA-600-72Hz 800x600 VESA-600-75Hz 1024x768 XGA 1024x768 COMPAQ-XGA 1024x768 VESA-768-70Hz 1024x768 VESA-768-75Hz 1024x768 APPLE MAC-768 1152x864 (60Hz) 1152x864 (70Hz) 1152x864 (75Hz) 1280x960 (60Hz) 1280x960 (70Hz) 1280x960 (75Hz) 1280x1024 VESA-1024-60Hz 1280x1024 VESA-1024-75Hz 31.469 70.087 24.83 56.42 31.469 70.087 31.5 70.15 31.469 50.030 31.469 59.94 35.00 66.67 37.861 72.809 37.5 75 31.469 70.087 49.725 74.55 35.156 56.25 37.879 60.317 48.077 72.188 46.875 75 48.363 60.004 53.964 66.132 56.476 70.069 60.023 75.029 60.24 75.02 54.054 59.270 63.851 70.012 67.50 75.00 60.00 60.00 70.00 70.00 75.00 75.00 64 60 80 75 POLARITY + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + (DOT/LINE) 800 449 848 440 800 449 800 449 800 629 800 525 864 525 832 520 840 500 900 449 1152 667 1024 625 1056 628 1040 666 1056 625 1344 806 1328 816 1328 806 1312 800 1328 803 1480 912 1480 912 1600 900 1800 1000 1800 1000 1800 1000 1688 1066 1688 1066 (DOT/LINE) 640 350 640 400 640 400 640 400 640 480 640 480 640 480 640 480 640 480 720 400 832 624 800 600 800 600 800 600 800 600 1024 768 1024 768 1024 768 1024 768 1024 768 1152 864 1152 864 1152 864 1280 960 1280 960 1280 960 1280 1024 1280 1024 WIDTH (DOT/LINE) 96 2 64 8 96 2 64 2 96 2 96 2 64 3 40 3 64 3 108 2 64 3 72 2 128 4 120 6 80 3 136 6 176 4 136 6 96 3 96 3 96 3 96 3 128 2 112 3 112 3 112 3 112 3 144 3 PORCH (DOT/LINE) 16 37 64 7 16 12 16 13 16 62 16 10 64 3 16 1 16 1 18 12 32 1 24 1 40 1 56 37 16 1 24 3 16 8 24 3 16 1 32 3 40 13 32 1 64 2 96 1 96 1 96 1 48 1 16 1 PORCH FOREQ.(MHZ) (DOT/LINE) 48 25.175 60 80 21.05 25 48 25.175 35 80 25.197 34 48 25.175 85 48 25.175 33 96 30.24 39 120 31.5 20 120 31.5 16 54 28.322 35 224 57.2832 39 128 36 22 88 40 23 64 50 23 160 49.5 21 160 65 29 112 71.664 36 144 75 29 176 78.75 28 176 80 29 192 80 32 200 94.499 44 256 108.00 32 312 108.00 36 312 126.00 36 312 135.00 36 248 108 38 248 135 38 SYNC TOTAL ACTIVE SYNC FRONT BACK PIXEL
Note: Mode 640x350, 640x400 and 720x400 will locate on middle position but cannot be expanded to full screen on vertical direction.
- 13 -
Support Modes
There will be 28 total support modes to accommodate the above mode and other video modes within the frequency range of the monitor.
85Hz refresh rate Support

Monitor should display 85Hz refresh rate mode as emergency mode. Monitor should display Out of Range warning menu at this mode.
Video input Connector

Analog Video input Connector: 15pins mini D-Sub Table 2.4.5. Pin assignment for D-sub connector PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Separate Sync RED VIDEO GREEN VIDEO BLUE VIDEO GROUND GROUND RED GROUND GREEN GROUND BLUE GROUND PC5V (+5V DDC) CABLE DETECTION GROUND SDA H.SYNC V.SYNC SCL Color of plastic parts: Blue (PC99)
5 10 15
1 6 11
D-sub connector
- 14 -
Monitor Block Diagram

The LCD monitor will contain an main board, an inverter/ power board, key board and internal adapter which house the flat panel control logic, brightness control logic and DDC. The inverter board will drive the backlight of panel and the DC-DC conversion. The Adapter will provide thr 12V DC-power to inverter/ power board.
Power board
(include: AC/DC,inverter)
- 15 -
BLOCK DIAGRAM
System Block Diagram
LVDS Signals
MCU
MVPRL including ADC, Scaling LVDS And OSD function
- 16 -
Monitor board layout
LABEL
U1 U2 U4 U6 U5 U7 U8 U9 U10 U11
Component
74LVC14 24LVC21 MVPRL M8064I 24LC16B MAX810 SI9435 LM4838 APL1085-3.3 CE APL1117-2.5 VC
LABEL
CN1 CN9 CN3 CN301 CN302 CN7
Component
D-SVB 15 PIN E&T 4501-10 E&T 6113-08 E&T 4501-11 E&T 4501-03 E&T DF14-30
- 17 -
Software flow chart
- 18 -
Software Flow Chart

1. 2. 3. 4. 5. 6. 7. 8. 9. MCU initialize Is the eeprom blank? Program the eeprom by default values. Get the PWM value of brightness from eeprom. Is the power key pressed? Clear all global flags. Are the < and > (Adjust key) and power key. Enter factory mode Save the power key status into eeprom. Turn on the LED and set it to green color. Scalar initialize. 10. In standby mode? 11. Update the lift time of back light. 12. Check the analog port, are there any signals coming? 13. Does the scalar send out a interrupt request? 14. Wake up the scalar 15. Are there any signal coming from analog port? 16. Display Cable Not Connected message, and go into standby mode after the message disappear. 17. Program the scalar to be able to show the coming mode. 18. Process the OSD display. 19. Read the key board. Is the power key pressed?
- 19 -
General Instructions
Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor. By changing these settings, the picture can be adjusted to your personal preferences. The power cord should be connected. Connect the video cable from the monitor to the video card. Press the power button to turn on the monitor position. The power indicator will light up.
AR577
AR578
External Controls 1 2 3 Auto Adjust Key/Exit </ Volume >/ Volume 4 5 6 MENU/ENTER LED / Power Key
- 20 -
System Installation
Connecting the Display

Power off your computer. Connect one end of the signal cable to the LCD Monitors VGA port. Connect the other end of the signal cable to the VGA port on your PC. Make sure connections are secure.
Connecting the AC Power

Connect the power cord to the LCD Monitor. Connect the power cord to an AC power source.
Connecting the Audio Cable

Connect the audio cable to the " LINE OUT " jack on your PC's audio card or to the front panel's AUDIO OUT jack of your CD ROM drive. Connect the other end of the audio cable to the LCD Monitor's " AUDIO IN " jack.
- 21 -
Chapter 2
Operating Instructions
CONTROLS
Control panel (monitor front panel)

1. Power ON/OFF switch, push to ON and push to OFF. (Toggle switch) 2. Power LED will be blue when monitor is on; be amber when in power saving mode. 3. Menu. 4. Adjust increase (Function select). Adjust decrease (Function select). 5. Auto adjustment Buttons.
Note:
1. Press button 4 (plus +) or (minus -) at the same time can activate Volume Adjustment. 2. When OSD Menu is off, press button 5 (auto) at the same time can activate Auto Adjustment immediately. 3. When into Factory mode press 4 (plus +),(minus -) and 1 (power) together 2 seconds at same time. 5. When into Burning mode press 5 (menus), 1 (power) together 2 second at same time.
- 22 -
Main OSD Menu:

Outline:
The description for control function :

Main Menu Icon Sub Menu Item Contrast Sub Menu Icon Contrast from Digital-register. Description Adjustment Range 0-100 Recall Cool Contrast Value Brightness Backlight Adjustment 0-100 Recall Cool Brightness Value Focus Adjust Picture Phase to reduce Horizontal-Line noise Clock Adjust picture Clock to reduce Vertical-Line noise. H. Position Adjust the horizontal position of the 0-100 picture. V. Position Adjust the verticalposition of the picture. Warm N/A Recall Warm Color Temperature from EEPROM. Cool N/A Recall Cool Color Temperature from N/A EEPROM.
- 23 -
Reset Value
0-100
Do Auto Config
0-100
Do Auto Config
Do Auto Config
0-100
Do Auto Config
N/A
The Color Temperature will be set to Cool.
User / Red
Red Gain from Digital-register.
0-100
100
User / Green
Green Gain Digital-register.
0-100
100
User / Blue
Blue Gain from Digital-register.
0-100
100
English c
N/A
Set OSD display language to English.
N/A
The Language will be set to English.
N/A
Set OSD display language to Tranditional Chinese.
N/A
Deutsch
N/A
Set OSD display language to German.
N/A
Franais
N/A
Set OSD display language to French.
N/A
Espaol Italiano
N/A N/A N/A
Set OSD display language to Spain. N/A Set OSD display language to Italian. N/A Set OSD display language to Simplified Chinese. N/A
N/A
Set OSD display language to Japanese.
N/A
H. Position
Adjust the horizontal position of the 0-100 OSD.
50
V. Position
Adjust the verticalposition of the OSD.
0-100
50
OSD Timeout
Adjust the OSD timeout.
10-120
10
Auto Config
N/A
Auto Adjust the H/V Position, Focus N/A and Clock of picture.
N/A
Information
N/A
Show the resolution, H/V frequency N/A and input port of current iput timing.
N/A
Reset
N/A
Clear each old status of Auto-configuration and set the color temperature to Cool.
N/A
N/A
Exit
N/A
Exit OSD
N/A
N/A
- 24 -
Hot-Key Menu:(For AR577 only)

Outline:
The description for Hot-Key function :

Item Volume Operation When the OSD is closed, press Left or Right button will be Volume Hot-Key Function Icon Adjustment Description Volume of Audio adjustment. The Audio will be Mute when volume=0. Range 0-100 Reset Value 50
OSD Message:
Outline:
The description for OSD Message :

Item Auto Config Please Wait Input Not Supported Cable Not Connected No Signal When the video cable is connected, but the is no active signal input, will show this message, then enter power saving. Description When User Press Hot-Key Auto, will show this message, and the monitor do the auto config function. When the Hsync Frequency, Vsync Frequency or Resolution is out of the monitor support range, will show this message. This message will be flying. When the video cable is not connected, will show this message. This message will be flying.
- 25 -
LOGO:
When the monitor is power on, the LOGO will be showed in the center.
Item of Factory menu

Vendor may customize design and add adjustment items Factory menu as far as all required items are included. 1) Bright Adjust Brightness and Contrast value to Max. 2) Auto Balance Adjust each R, G, B contrast (gain) and offset. Method of auto adjust is depends on hardware.
Adjusted value of R, G, B gain shall be used for initial value of Contrast in user menu. All value shall be adjustable manually. This function shall be located in 3. tag of Factory menu.
3) Factory color temp data edit Following data for color temp shall be editable manually. -color temp default preset No.
- 26 -
Plug and play

Plug & play DDC2B feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The communication channel is defined in two levels, DDC2B. The DDC2Bis a bidirectional data channel based on the I C protocol. The host can request EDID information over the DDC2B channel.
2
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL. This monitor meets the Green monitor standards as set by the Video Electronics Standards Association(VESA) and/or the United States Environmental Protection Agency (EPA) and The Swedish Confederation Employees (NUTEK). This feature is designed to conserve electrical energy by reducing power consumption when there is no video-input signal present. When there is no video input signal this monitor, following a time-out period, will automatically switch to an OFF mode. This reduces the monitors internal power supply consumption. After the video input signal is restored, full power is restored and the display is automatically redrawn. The appearance is similar to a Screen Saver feature except the display is completely off. The display is restored by pressing a key on the keyboard, or clicking the mouse.
Using The Right Power Cord

The accessory power cord for the Northern American region is the wallet plug with NEMA 5-15 style and is UL listed and CSA labeled. The voltage rating for the power cord shall be 125 volt AC. Supplied with units intended for connection to power outlet of personal computer: Please use a cord set consisting of a minimum No. 18 AWG, type SJT or SVT three conductors flexible cord. One end terminates with a grounding type attachment plug, rated 10A, 250V,CEE-22 male configuration. The other end terminates with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration. Please note that power supply card needs to use VDE 0602, 0625, 0821 approval power cord in European counties.
- 27 -
White Color Temperature

White color temperature is 4 preset as 9300, 7500,6500 and User, Default value of user color should be user which is maximum setting for panel. Target of color setting Color Temp. x 9300K 6500K User 0.283 0.313 y 0.297 0.329 +0.03 +0.03 u 0.189 0.198 v 0.446 0.469 @uv < 0.01* @uv < 0.01* Color Coordinate Tolerance Color Coordinate Tolerance
*) TCO0X A.2.6.1 requirement User should follow Microsoft Windows Color Quality Specification for Liquid Crystal Display OEMs. (http://www.microsoft.com/hwdev/tech/color/ColorTest.asp)
Audio Technical specification (For AR577 only)

General Description:
Output power Total harmonic distortion Input signal sensitivity Input impedance Frequency response range Difference of L and R output : 1W + 1W maximum : Less than 1 % (except speakers distortion) : 0.5 Vrms for full output : 47 Kohm +/- 5 %
: 20Hz 20kHz (except speakers response) : Less than 2 dB
- 28 -
Electrical characteristics (Tamb=25)

Audio amplifier(USE Panasonic VP-7723A Audio Analyzor. ) Item Audio Input Freq. Min. Input Voltage(V) Spec. Typ. 0.5Vm s Input Current(m A) Audio Voltage Gain Frequency Response 500m Vrms 1KHz 500 800 6dB Volume Max.,load 4 Max. Comment
500m Vrms 300Hz-20KH -10dB z
+10d B Volume Max.,load 4
Signal to Noise ratio Total harmonic distortion Cross talk Output Watt. Volume Control
500m Vrms 1KHz 500m Vrms 1KHz 500m Vrms 1KHz 500m Vrms 1KHz
-40dB Volume Max.,load 4 1% except speakers distortion
-30dB Volume Max.,load 4 0.5W Volume Max.,load 4 Analog
Speakers
Maximum power Impedance Frequency response range Total harmonic distortion : : : : 2 W per speaker(max) 4 ohm +/- 15 % Less than 5 % @ 1kHz 1.0Hz @ 0.125 W 1kHz 300 Hz 20 kHz (S.P.L. 10 dB)
- 29 -
Chapter 3
Machine Disassembly and Replacement
The step between front bezel and back cover shall be within specification. Top and Bottom Back cover & Bezel concavity 0.8mm A 1.3 mm Left and Right Back cover & Bezel concavity 0.8mm A 1.3 mm
Back Cover & Hinge Cover concavity 0mm B 0.5mm
- 30 -
Base & Neck concavity 0mm C 0.6mm
Top and Bottom Back cover & Bezel step 0mm D 0.8 mm
Left and Right Back cover & Bezel step 0mm D 0.8 mm
- 31 -
LCD Horizontally
The angle between front bezel and LCD unit in bottom side should not large than 1.0mm.
The distance of the LCD display unit from left side to right should not large than 4.0mm.
- 32 -
Tilt Base Rotation

Tilt up 15 2X down 5 / 2X
Plastic Material
For TCO99 Front Bezel Back Cover The Others For MPRII Front Bezel Back Cover The Others ABS ABS ABS 94V-0 94V-0 94HB PC+ABS PC+ABS ABS 94HB
GAP Spec.
Gap between panel with bezel is 0 mm < gap < 1.2 mm
- 33 -
Machine assembly
PICTURE DESCRIPTION
Connect the FPC line on panel.
Assemble the chassis onto panel.
Firmly secure the Panel with 4 screws.
Plug two speakers to put on bezel.
1. Connect the 13P line with VK board. 2. Firmly secure the VK board with 4 screws.
AR578
AR577
34
Connect speaker wires on VK board. (For AR577 only)
Connect the bezel with monitor.
To reverse the monitor.
Assemble the power board onto chassis.
AR577
AR578
35
Firmly secure the power board with 5 screws.
AR577
AR578 Firmly secure the power cable with screws.
AR577
AR578 Connect four panel voltage line on power board.
36
1. Assemble the VL board onto chassis. 2. Firmly secure the VlL board with 3 screws.
Firmly secure the VlL board and line with screws.
Connect the FPC on VL board.
Connect the power line on VL board.
Connect the VL-VK line on VL board.
AR577
AR578
37
Connect the audio line on power board. (For AR577 only)
Firmly secure the line and chassis with 4 screws.
Check it.
AR577
AR578 Put the EMI cover on monitor..
Put the screws on EMI cover with monitor.
38
Put the screws on EMI cover with monitor.
1. Connect the back cover with monitor. 2. Firmly secure the back cover with 4 screws.
1. Assemble the neck bracket onto neck. 2. Firmly secure the neck bracket with 4 screws.
1. Connect the hinge with neck. 2. Firmly secure the hinge with 3 screws.
1. Assemble the neck with back cover. 2. Firmly secure the neck with 4 screws.
Assemble the base with monitor
39
Chapter 4
Troubleshooting
Main Procedure
40
Power Circuit and Backlights Troubleshooting
41
Performance Troubleshooting
42
Function Troubleshooting
43
Chapter 5
Connector Information
Phonejack stereo
PIN1. PIN2. PIN3. right Left Gnd : Line-in receptacle
J1
: CEE22 typed connector
1 2 3
PHONEJACK STEREO
Video input Connector

Analog Video input Connector: 15pins mini D-Sub Table 2.4.5. Pin assignment for D-sub connector Separate Sync
PIN NO.
5 10 15
1 6 11
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
RED VIDEO GREEN VIDEO BLUE VIDEO GROUND GROUND RED GROUND GREEN GROUND BLUE GROUND PC5V (+5V DDC) CABLE DETECTION GROUND SDA H.SYNC V.SYNC SCL
44
Chapter 6
FRU (Field Replaceable Unit) list
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of AL1715p. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization). NOTE : Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on your regional web or channel(http://aicsl.acer.com.tw/spl/). For whatever reasons a part number change is made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED CERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer office to order FRU parts repair and service of customer machines. NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how best to dispose it, or follow the rules set by your regional Acer office on how to return it.
45
Model: AR577
46
Model:AR578
47
Part list A. For AL1715p No. Photo Part Name Description Vendor No.
Back Cover Screws
M4X0.7+6P-NI
MAA20093004
BaseASSY(FOOT)
AR7714A(ABS94HB,MCG62) FAAR7714A10
Stand Screws
M4X0.7+11P-MC WASHER DIM 8.0
MAA70002400
NECK COVER
AR7721(ABS94HB,MCG62) FAAR7721100
NECK BRACKET
AR7722(SECC1.0)
ECAR7722000
HINGE ASSY
AR7717(SK-7,T=22)
ECAR7717000
NECK
AR7713(ABS94HB.MCG62) FAAR7713100
Panel & Chassis
M3X0.5+4I-NI
MAA00001240
10
Function Board
VK-583 LAR577Y
454AAP30001
11
BACK COVER, Neck TPP-4.0+10P-NI & Neck Bracket, Chassis & Bezel
MAB20074201
48
12
Back Cover
AR7712A(PC+ABS,MCG62) FAAR7712A10
13
Hinge Screws
TPB-4+8C-MC
MAB7T002401
14
Mainboard & Chassis
4#40UNCX12.7 PLS-WASHER
MAAA0019400
15
Speaker (R/L)
2W 40HM 37.5X17X9.5mm 50mm
CG10021V920 CG10021V930
16
POWER BOARD &CHASSIS
M3x0.5+6F-ZK
MAA10022007
17
Invertor Board
VP-583 LAR577Y
453AAP30001
18
Key/B & Bezel
TPP2X3+12B-MC
MAB80007400
19
POWER BOARD &CHASSIS Function board to Mainboard cable
M4.0X0.7+8BTF-MC
MAA80014400
20
AR577 CTRL-KEY 13P
DC020162300
21
Main Shield
AR7716(TIN0.3)
ECAR7716000
22
Mainboard and M3X0.5+4C-NI Invertor Board Screws
MAA70003100
49
23
Mainboard
VL-731 LAR577Y
461AAI300E1
24
Frame(BEZEL)
AR7711A (PC+ABS,MCG62) FAAR7711A10
25
Main Frame/CHASSIS
AR7715(SECC1.0)
ECAR7715000
26
Mainboard to LCD Cable
JP577 PANEL-CTRL 30P
DC020160700
27
LCD Panel(F)
HT17E12-200 17(HYDIS)
AC6V0000200
28
LCD Panel(B)
HT17E12-200 17(HYDIS)
AC6V0000200
50
B. For AR577 (Acer model:AL1715 bm ) No.

1
Photo
Part Name
BACK COVER SCREWS
Description
M4X0.7+6P-ZK
Part No.
MAA20093300
BACK COVER, Neck TPP-4.0+10P-ZK & Neck Bracket, Chassis & Bezel
MAB20074202
BaseASSY(FOOT)
AR7714A(ABS94HB,MBK24)
FAAR7714A00
Stand Screws
MAA70002400
NECK COVER
AR7721(ABS94HB,MBK24)
FAAR7721000
NECK BRACKET
AR7722(SECC1.0)
ECAR7722000
HINGE ASSY
AR7717(SK-7,T=22)
ECAR7717000
NECK
AR7713(ABS94HB.MBK24)
FAAR7713000
Panel & Chassis
M3X0.5+4I-NI
MAA00001240
10
Function Board
VK-583 LAR577Y
454AAP30001
11
Back Cover
AR7712A(PC+ABS,MBK24) FAAR7712A00
12
Hinge Screws
TPB-4+8C-MC
MAB7T002401
51
13
Mainboard & Chassis
MAAA0019400
14
Speaker (R/L)
2W 40HM 37.5X17X9.5mm 50mm
CG10021V920 CG10021V930
15
M3x0.5+6F-ZK
MAA10022007
16
Invertor Board
VP-583 LAR577Y
453AAP30001
17
Key/B & Bezel
TPP2X3+12B-MC
MAB80007400
18
M4.0X0.7+8BTF-MC
MAA80014400
19
Function board to Mainboard cable
AR577 CTRL-KEY 13P
DC020162300
20
Main Shield
AR7716(TIN0.3)
ECAR7716000
21
MAA70003100
22
Mainboard
VL-731 LAR577Y
461AAI300E1
52
23
Frame(BEZEL)
AR7711A (PC+ABS,MBK24) FAAR7711A00
24
Main Frame/CHASSIS
AR7715(SECC1.0)
ECAR7715000
25
DC020160700
26
LCD Panel(F)
HT17E12-200 17(HYDIS)
AC6V0000200
27
LCD Panel(B)
HT17E12-200 17(HYDIS)
AC6V0000200
53
C. No.
For AR578 (Acer model:AL1715 ) Photo Part Name Description Part No.
Back Cover Screws
M4X0.7+6P-NI
MAA20093004
BaseASSY(FOOT)
AR7714A(ABS94HB,MCG62) FAAR7714A10
Stand Screws
MAA70002400
NECK COVER
AR7721(ABS94HB,MCG62) FAAR7721100
NECK BRACKET
AR7722(SECC1.0)
ECAR7722000
HINGE ASSY
AR7717(SK-7,T=22)
ECAR7717000
NECK
AR7713(ABS94HB.MCG62) FAAR7713100
Panel & Chassis
M3X0.5+4I-NI
MAA00001240
10
Function Board
VK-583 LAR578Y
454AAP30011
11
BACK COVER, Neck TPP-4.0+10P-NI & Neck Bracket, Chassis & Bezel
MAB20074201
54
12
Back Cover
AR7812A(PC+ABS,MCG62) FAAR7812A10
13
Hinge Screws
TPB-4+8C-MC
MAB7T002401
14
Mainboard & Chassis
MAAA0019400
15
M3x0.5+6F-ZK
MAA10022007
16
Invertor Board
VP-583 LAR578Y
453AAP30011
17
Key/B & Bezel
TPP2X3+12B-MC
MAB80007400
18
M4.0X0.7+8BTF-MC
MAA80014400
19
AR578 CTRL-KEY 13P
DC020162500
20
Main Shield
AR7816(TIN0.3)
ECAR7816000
21
MAA70003100
22
Mainboard
VL-731 LAR578Y ABO
461AAI300E2
55
23
Frame(BEZEL)
AR7811A (PC+ABS,MCG62) FAAR7811A10
24
Main Frame/CHASSIS
AR7715(SECC1.0)
ECAR7715000
25
DC020160700
26
LCD Panel(F)
HT17E12-200 17(HYDIS)
AC6V0000200
27
LCD Panel(B)
HT17E12-200 17(HYDIS)
AC6V0000200
56
D. For AR578 (Acer model:AL1715 b) No.

1
Photo
Part Name
Back Cover Screws
Description
M4X0.7+6P-ZK
Part No.
MAA20093300
BaseASSY(FOOT)
AR7714A(ABS94HB,MBK24)
FAAR7714A00
Stand Screws
MAA70002400
NECK COVER
AR7721(ABS94HB,MBK24)
FAAR7721000
NECK BRACKET
AR7722(SECC1.0)
ECAR7722000
HINGE ASSY
AR7717(SK-7,T=22)
ECAR7717000
NECK
AR7713(ABS94HB.MBK24)
FAAR7713000
Panel & Chassis
M3X0.5+4I-NI
MAA00001240
Function Board
VK-583 LAR578Y
454AAP30011
10
BACK COVER, Neck TPP-4.0+10P-ZK & Neck Bracket, Chassis & Bezel
MAB20074202
11
Back Cover
AR7812A(PC+ABS,MBK24) FAAR7812A00
57
12
Hinge Screws
TPB-4+8C-MC
MAB7T002401
13
Mainboard & Chassis
MAAA0019400
14
M3x0.5+6F-ZK
MAA10022007
15
Invertor Board
VP-583 LAR578Y
453AAP30011
16
Key/B & Bezel
TPP2X3+12B-MC
MAB80007400
17
M4.0X0.7+8BTF-MC
MAA80014400
18
AR578 CTRL-KEY 13P
DC020162500
19
Main Shield
AR7816(TIN0.3)
ECAR7816000
20
MAA70003100
21
Mainboard
VL-731 LAR578Y ABO
461AAI300E2
22
Frame(BEZEL)
AR7811A (PC+ABS,MBK24) FAAR7811A00
58
23
Main Frame/CHASSIS
AR7715(SECC1.0)
ECAR7715000
24
DC020160700
25
LCD Panel(F)
HT17E12-200 17(HYDIS)
AC6V0000200
26
LCD Panel(B)
HT17E12-200 17(HYDIS)
AC6V0000200
59
POWER/Inverter Board
Description
This specification defined the performance and characteristic of power/inverter board. It supplies the following outputs : 1). 5Vdc: Logic power. 2). 5Vaudio: Audio power. 3). 15Vinv: Inverter power.
Features
Input Voltage: 100 ~ 240 10H Vac Input current: 1.2Amax. at 90Vac Input Frequency: 47 ~ 63Hz Input power saving consumption: Less than 1.2W @ minimum load Total output power: 60Wmax Inverter brightness adjustment: Burst mode Protection function: auto-recovery type
Interface Signals
Input
1. AC Inlet: HUAJIE SA-4S-066 or compatible. 2. J701: SC SCJ-0345-1-X-9 3.6D BLU 3P or compatible.
Output Connector & Pin Assignment:

1. The connecter was pitch 2.0mm, cable length was 125mm. PIN NO. 1 2 3 4 5 6 7 8 9 10 Function +5Vaudio GND GND GND Vbri ---Ven +5Vdc +5Vdc +5Vdc Audio power (optional). Audio ground Ground Ground Brightness control from logical board (0V to 3.3V) ----Inverter enable signal from logical board (high active , >3V) +5Vdc supply for logical board +5Vdc supply for logical board +5Vdc supply for logical board
60
Function
2.Inverter-side connecter : SM02B-BHSS-1-TB(JST) for AR577 / SM02(8.0)B-BHS-1(JST) for AR599 or equivalent. PIN NO. 1 2 Function Cth Ctl Comment VBLH(High voltage) VBLL(Low voltage)
Electrical Specification:
AC-DC Electrical specification
Input Specification No 1 2 3 4 5 6 7 8 Item Input Voltage Input Frequency Input Current Inrush Current Hold Up Time Turn on time Efficiency Consumption Condition ------------Cold Start @Vin=100Vrms Cold Start @Vin=240Vrms @full load & 100Vac input Vin =110Vac Full load Vin=240Vac,@ no load 10 ------Min. 100 47 ----Typ. ------------1.0 70 --Max. 240 63 1.0 30 50 ------1 Unit Vac Hz Arms A0-P A0-P ms S % W
61
AC-DC Output Specification Tolerance Output Voltage +5Vdc +15Vinv +5Vaudio Ripple --+5 /-3 % +35/-5 % 5% 1. Measured at DC output terminals which are paralleled with a 10uf Ecap &0.1uf Ceramic cap. 2.Band width is limited within 20MHz. 50~100% or 100~50% Dynamic Load Regulation load change of any DC output @50% duty of 1MHz (min.) Over / Under Shoot @ Power line on/off --5% ----5% --Output Current Voltage Tolerance MIN 0.05A 0A 0A --MAX 1.5A 2A 0.6A 1% 4.85~5.25V dc 20~14.3Vdc 4.75~5.25Vdc +5Vdc:50mVp-p +15Vinv:150mVp-p +5Vdc:150mVp-p +15Vinv:450mVp-p
Noise
---
3%
*+5Vdc load regulation test: the +15Vinv loading at 2.0A *+15Vinv load regulation test: the +5Vdc loading at 1.5A
Protection function
1) SCP: Short circuit protection must be acted on both outputs 2) OPP: Should be protected when output power consumption is within 60W ~ 75W
62
Inverter Electrical Specification:

For Hydis HT17E12-200 (AR577)
Condition Input Voltage Input Current Backlight ON/OFF Control ----ON OFF Brightness Adjust Output Voltage Brightness Output Current(Each connector) Frequency Lamp start voltage Striking Time Lamp Current Balance Efficiency Operating Life Time Min. Luminance / Max. Luminance Vin=15V, Iout=6.5mA lamp current in 6.5mA Vbri=0.4V~3.3V --@0J ----Vin=15V ------40000 690 200 3 30 --700 250 6.5 --1340 1 0.3 80 50000 7 70 1570 --------840 Vrms Cd/m mA KHz Vrms S mA % Hr --Min. ----Typ. 15 1.5 3.3 0 30% --Max. ----Unit V A V V ---
*.The open lamp voltage is testes at output connector terminal
SAFETY
Leakage Current: 0.25mA @ 100Vac Insulation Resistance: more than 3M ohms while withstanding a voltage of 500Vac Hi-Pot: 3Kvac with using 3mA cut off current
63
Power Consumption
The monitor is equipped with a power-management according to the below. There is a delay of 5s 7s before the transition from On-state to any power saving state to avoid unintentionally entering of a power saving stage during display resolution and timing mode changes. Transition from any power saving state to another can be instantaneous. The recovery from Off-state requires no manual power on. Mode Power-On Power-off Switch-off SYNC. On means: Normal operation SYNC. Off means: H sync. V sync. F < 10KHz duty cycle > 25% F < 10Hz duty cycle > 25% H-Sync. on off V-Sync. on off Video active blanked Pw-cons. < 75W <5W < 5W Indicator Green LED Orange LED Dark LED Rec. time* -< 5S
CONNECTORS / CONTROLS
Connectors Power Analog RGB 1 2 3 4 5 6 7 8 Audio Red Video Green Video Blue Video Serial Clock for ISP Ground Red Ground Green Ground Blue Ground : Monitor rear side -PC I/P for PC : : 3.5mm Stereo female : Monitor rear side : Monitor rear side / Data Cable 9 10 11 12 13 14 15 : AC Inlet : 15-pin D-sub female / male
Pin Assignment of 15-pin D-sub: +5V FOR DDC Detect Serial Data for ISP Serial Data for DDC H-Sync. V-Sync. Serial Clock for DDC
Monitor Control Keys

KEY : Power , Menu , Adjust +/- , Vol +/-, Auto
Position Of Controls
Position of all switches Position of LED : Bottom side of front bezel : Bottom side of front bezel
64
Chapter 7
Schematic Diagram
65
66
67
68
69
70
71
72
73
74
75
M170EG01 V.1
Product Specification
AU OPTRONICS CORPORATION
17.0 SXGA Color TFT-LCD Module
Model Name:
M170EG01 V.1
Approved by
Prepared by
CC Chiu
Customer
Regina Tsou
DDBU Marketing Division / AU Optronics corporation Checked & Approved by
Ver0.4
1/29
M170EG01 V.1
17.0 SXGA Color TFT-LCD Module Model Name: M170EG01 V.1
) Preliminary Specifications () Final Specifications
Note: This Specification is subject to change without notice.
Ver0.4
2/29
Contents
1.0 Handling Precautions ............................................................ 7 2.0 General Description ............................................................... 8
2.1 Display Characteristics .....................................................................................................8 2.2 Functional Block Diagram..................................................................................................9 2.3 Optical Characteristics.................................................................................................... 10 2.4 Pixel format image ........................................................................................................ 13
3.0 Electrical characteristics...................................................... 14

3.1 Absolute Maximum Ratings.............................................................................................. 14 3.2 Connectors ................................................................................................................. 15 3.3 Signal Pin................................................................................................................... 15 3.4 Signal Description ......................................................................................................... 16 3.5 Signal Electrical Characteristics......................................................................................... 19 3.6 Interface Timings .......................................................................................................... 19 3.6.1 Timing Characteristics .......................................................................................... 19 3.6.2 Timing Definition ................................................................................................. 20 3.8 Power ON/OFF Sequence ............................................................................................... 22
4.0 Backlight Characteristics ..................................................... 23

4.1 Signal for Lamp connector ............................................................................................... 23 4.2 Parameter guideline for CCFL Inverter................................................................................. 23
5.0 Vibration, Shock, and Drop .................................................. 24

5.1 Vibration & Shock ......................................................................................................... 24 5.2 Drop test .................................................................................................................... 24
6.0 Environment ........................................................................ 24

6.1 Temperature and Humidity............................................................................................... 24 6.1.1 Operating Conditions............................................................................................ 24 6.1.2 Shipping Conditions ............................................................................................. 24 6.2 Atmospheric Pressure .................................................................................................... 25 6.3 Thermal Shock............................................................................................................. 25
7.0 Reliability ............................................................................ 25

7.1 Failure Criteria ............................................................................................................. 25 7.2 Failure Rate ................................................................................................................ 25 7.2.1 Usage ................................................................................................................ 25
8.0 Safety .................................................................................. 26

8.1 Sharp Edge Requirements............................................................................................... 26 8.2 Materials .................................................................................................................... 26 8.2.1 Toxicity .............................................................................................................. 26 8.2.2 Flammability ....................................................................................................... 26 8.3 Capacitors .................................................................................................................. 26
9.0 Other requirement............................................................... 27

Ver0.4 3/26
M170EG01 V.1
9.1 National Test Lab Requirement ......................................................................................... 27 9.2 Label ........................................................................................................................ 27
10.0 Mechanical Characteristics ................................................ 28
Ver0.4
4/29
M170EG01 V.1
Record of Revision
Version and Date Page Old description 0.1 2004/2/17 0.2 2004/2/27 All 8,14 First Edition for Customer Type P/N New Description All FI-XB30SRL-HF11/ Modified MDF76LBRW-30S1H Mating P/N Housing HRS Mating Housing JAE FI-X30C2L /HRS Remark
FI-XB30SRL-HF11 Type P/N
MDF76LBRW-30S- P/N 1H (HIROSE)
MDF76G-30P-1SD Response time: Rising Time Typ = 12ms Falling Time Typ = 4ms 3.1 Absolute Maximum Ratings Vin Min=-0.3 , Max=+6 Note1:Start from left side Note3: Please follow PSWG. Follow PSWG Modified Added Modified Modified
10
Response time: Rising Time Typ = TBD Falling Time Typ = TBD
13
3.1 Absolute Maximum Ratings Vin Min=+4.5 , Max=+5.5
16
3.4 Signal Description No note
17
3.4 Signal Description Picture format
20 9,11 18 18 20
LCD Inrush Current : TBD No define 3.5 Signal Electrical Characteristics Frame Rate Min = no definition VDD Current Typ=1100mA Max=1210mA
LCD Inrush Current : 2.5 A Flicker New definition Frame Rate Min = 50Hz VDD Current Typ=1200mA Max=1560mA VDD Power Typ=6W Max=7.8W CCFL connector 2pin 2
Modified Added Modified Added Modified
20
VDD Power Typ=5.5W Max=6.05W
Modified
0.3 2004/4/1
9 14 19 23
2.2 Functional Block Diagram 3.1 Absolute Maximum Ratings 3.6.1 Timing Characteristics 4.2 Parameter guideline for
Added Modified Added
CCFL max. current = 8.5mA DE mode only
CCFL Note 1: The variance of the current is Deleted 10%
Inverter 23 4.2 Parameter guideline for
CCFL CCFL Ignition Voltage (End of the lamp wire connector)
Added
Inverter
Ver0.4
5/29
M170EG01 V.1
23 4.2 Parameter guideline for CCFL The minimum lifetime of CCFL is on the Added condition at 7.5mA lamp current. Inverter Note4 0.3 2004/4/6 10 2.3 Optical Characteristics Response Time Max. = TBD Rising Time Max. = 20 Falling Time Max. = 5 Rising + Falling Max. = 25 10 2.3 Optical Characteristics White Luminance Min. = TBD 9 8 10 2.2 Functional Block Diagram Contrast Ratio = TBD Contrast ratio Min. = TBD Contrast ratio Typ. = TBD 0.3 2004/4/8 10,12 TC0-03 Compliance No defined 9,15 3.2 Mating Type Part Number SM02(4.0)B-BHS-1-TB 0.4 2004/5/25 23 4.1 Signal for Lamp connector Modified to SM02B-BHSS-1-TB Modified Modified Adding CCFL connector diagram Contrast Ratio = 450 : 1 Contrast ratio Min. = 250 Contrast ratio Typ. = 450 Note 5 Added Added Modified Modified White Luminance Min. = 210 Modified Modified
4.1 Signal for Lamp connector
10
Viewing Angle Cr=10, Down Typ.=70 Down Min.=60
Viewing Angle Cr=10, Down Typ.=60 Down Min.=50 Note 3:8-bit in
Modified
18
The input data format No defined
Added
19
3.6.1 Timing Characteristics Data CLK Min.=45 Frame Rate Min.=50
3.6.1 Timing Characteristics Data CLK Min.=40 Frame Rate Min.=49 CCFL life Time Min.=30,000 hours Typ.=50,000 hours
Modified
23
CCFL life Time
Modified
Ver0.4
6/29
M170EG01 V.1
1.0 Handling Precautions

1) Since front polarizer is easily damaged, pay attention not to scratch it. 2) Be sure to turn off power supply when inserting or disconnecting from input connector. 3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. 4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling. 7) Do not open nor modify the Module Assembly. 8) Do not press the reflector sheet at the back of the module to any directions. 9) In case if a module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the CCFL reflector edge. Instead, press at the far ends of the CCFL reflector edge softly. Otherwise the TFT module may be damaged. 10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface Connector of the TFT module. 11) After installation of the TFT module into an enclosure (Desktop monitor Bezel, for example), do not twist nor bend the TFT Module even momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the TFT module from outside. Otherwise the TFT module may be damaged.
Ver0.4
7/29
M170EG01 V.1
2.0 General Description

This specification applies to the 17.0 inch Color TFT/LCD Module M170EG01 V0. This module is designed for a display unit of personal computer. The display supports the SXGA (1280(H) x 1024(V)) screen format and 16.2M colors (RGB 6-bits + FRC data). All input signals are 2 Channel LVDS interface compatible. This module does not contain an inverter card for backlight.
2.1 Display Characteristics

The following items are characteristics summary on the table under 25 J ITEMS Screen Diagonal Active Area Pixels H x V Pixel Pitch Pixel Arrangement Display Mode White Luminance Contrast Ratio Optical Rise Time/Fall Time Color Saturation Nominal Input Voltage VDD Power Consumption (VDD line + CCFL line) Weight Physical Size Unit [mm] [mm] [mm] condition:
[cd/m2] [msec] [Volt] [Watt] [Grams] [mm]
Electrical Interface Support Color Temperature Range Operating Storage (Shipping)
SPECIFICATIONS 432(17.0") 337.920 (H) x 270.336(V) 1280(x3) x 1024 0.264 (per one triad) x 0.264 R.G.B. Vertical Stripe Normally White 260 (Typ) 450 : 1 (Typ) 16 (Typ) 72% NTSC +5.0 V 25.8 W(Typ) (PDD=6 W, PCFL=19.8 W @Lamp=7.5mA) 1900 (Typ) Min. Typ. Max. Horizatal(H) 358 358.5 359.0 Vertical(V) 296 296.5 297 Depth(D) 16.5 17.0 17.5 Dual Channel LVDS 16.2M colors (RGB 6-bit + FRC data) 0 to +50 -20 to +60
[oC] [oC]
Ver0.4
8/29
M170EG01 V.1
2.2 Functional Block Diagram

The following diagram shows the functional block of the 17.0 inches Color TFT/LCD Module:
AU ASIC
Timing Controller
G1
LVDS
LVDS RSDS G1024 D1
TFT-LCD 1280*(3)*1024 Pixels
Connector
+ 5V
D3840 4 CCFL
DC/DC Converter
Gamma Correction
DC POWER
Inverter
FI-XB30SRL-HF11 / MDF76LBRW-30S-1H Mating Type: JAE FI-X30C2L / HRS MDF76G-30P-1SD
JST-BHSR-02VS-1 ( 2pin SM02B-BHSS-1-TB
2)
Ver0.4
9/29
M170EG01 V.1
Product Specification 2.3 Optical Characteristics

The optical characteristics are measured under stable conditions at 25J (Room Temperature): Item Unit Conditions Min. Typ. Max. Horizontal (Right) 60 70 CR = 10 (Left) 60 70 Viewing Angle [degree] Vertical (Up) 60 70 CR = 10 (Down) 50 60 Contrast ratio Normal Direction Rising Time Response Time [msec] Falling Time Rising + Falling Red x Red y Color / Chromaticity Coordinates (CIE) Green x Green y Blue x Blue y Color White White Luminance @ CCFL 7.5mA (center) Luminance Uniformity Crosstalk (in 75Hz) Flicker TC0-03 Compliance Equipment: Pattern Generator, Power Supply, Digital Voltmeter, Luminance meter (PR 880, BM-5A / BM7) [cd/m ] [%] [%] dB
2
Note -
250 0.61 0.31 0.26 0.58 0.11 0.04 0.28 0.30 210 75
450 12 4 16 0.64 0.34 0.29 0.61 0.14 0.07 0.31 0.33 260 80
20 5 25 0.67 0.37 0.32 0.64 0.17 0.10 0.34 0.36
Note 1
Note 2
Coordinates
(CIE)
White x White y
1.5 -20
Note 3 Note 4 Note 5
Aperture Test Point Environment
1X with 100cm VD or 2X with 50cm viewing distance Center (VESA point 9) < 1 lux
Module Driving Equipment
LCD Module
measuring distance
Ver0.4
PR-880 / BM5A / BM7
10/29
M170EG01 V.1
Note 1: Definition of Response time The output signals of photodetector are measured when the input signals are changed from Black to White (rising time), and from White to Black (falling time), respectively. The response time is interval between the 10% and 90% of amplitudes.
Tr F
Tr R
100 90 Optical response 10 0

Note 2: Brightness uniformity of these 9 points is defined as below 90 % 50 % 10 % 10 %
White
Black
White
50 %
90 %
Uniformity =
Minimum Luminance in 9 points (1 - 9) Maximum Luminance in 9 Points (1 - 9)
Ver0.4
11/29
M170EG01 V.1
Note 3: 1/2 1/6 1/6 2/3 1/2 1/3 1/6
1/6 1/3 1/2 B 2/3
1/2 B 184 gray level 184 gray level
0 gray level l LA-LA l / LA x 100%= 1.5% max., LA and LB are brightness at location A and B l LB-LB l / LB x 100%= 1.5% max., LA and LB are brightness at location A and B Note4: Test Paterm : Subchecker Pattern R GB R GB Gray Level = L127 R GB R GB Gray Level = L0
Unit: percentage of dimension of display area
R GB R GB
Method : Record dBV & DC value with (WESTAR)TRD-100 Amplitude
AC
DC Time
Flicker (dB) = 20 log
AC Level(at 30 Hz) DC Level
Note5:Tuning the brightness and contrast function in OSD let the luminance to 125 cd/m2. When tuning the brightness to 125cd/m2, the function on OSD should not restrict our V-T curve. In other word, the higher contrast, the range of panels V-T curve will be more extensive to get the better performance. If it is not possible to achieve the test luminance by this procedure it is suitable to tune contrast higher and brightness lower.
Ver0.4
12/29
M170EG01 V.1
Product Specification 2.4 Pixel format image

Following figure shows the relationship of the input signals and LCD pixel format.
ODD
EVEN
ODD
EVEN
ODD
EVEN
1 ST
R G B R G B R G B
R G B R G B R G B
1024 TH
R G B R G B R G B
R G B R G B R G B
Ver0.4
13/29
M170EG01 V.1
3.0 Electrical characteristics

3.1 Absolute Maximum Ratings
Absolute maximum ratings of the module is as following: Item Logic/LCD Drive Voltage CCFL Current Operating Temperature Operating Humidity Storage Temperature Storage Humidity Note : Symbol VIN ICFL TOP HOP TST HST Min -0.3 0 8 -20 8 Max 6 8.5 +50 95 +60 95 Unit [Volt] [mA] rms [oC] [%RH] [ C] [%RH]
o
Conditions
Note Note Note Note
Maximum Wet-Bulb should be 39J
and No condensation.
Relative Humidity %
Twb=39J T=40J ,H=95% 100 95 80 T=50J ,H=55% 60
40
Storage range
T=60J ,H=39%
Operation range Storage range
T=65J ,H=29%
20 5 0 -20 0
50
60
Temperature J
Ver0.4
14/29
M170EG01 V.1
Product Specification 3.2 Connectors

Physical interface is described as for the connector on module. These connectors are capable of accommodating the following signals and will be following components.
Connector Name / Designation Manufacturer Type Part Number Mating Housing Part Number
Interface Connector / Interface card JAE or compatible FI-XB30SRL-HF11 / MDF76LBRW-30S-1H JAE FI-X30C2L / HRS MDF76G-30P-1SD
Connector Name / Designation Manufacturer Type Part Number Mating Type Part Number
Lamp Connector / Backlight lamp JST BHSR-02VS-1 SM02B-BHSS-1-TB
3.3 Signal Pin

Pin# 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 Signal Name RxOIN0RxOIN1RxOIN2VSS RxOCLKIN+ RxOIN3+ RxEIN0+ RxEIN1VSS RxEIN2+ RxECLKIN+ RxEIN3+ VSS VSS VCC Pin# 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Signal Name RxOIN0+ RxOIN1+ RxOIN2+ RxOCLKINRxOIN3RxEIN0VSS RxEIN1+ RxEIN2RxECLKINRxEIN3VSS NC VCC VCC
Ver0.4
15/29
M170EG01 V.1
Product Specification 3.4 Signal Description

The module using a pair of LVDS receiver SN75LVDS82(Texas Instruments) or compatible. LVDS is a differential signal technology for LCD interface and high speed data transfer device. Transmitter shall be SN75LVDS83(negative edge sampling) or compatible. The first LVDS port(RxOxxx) transmits odd pixels while the second LVDS port(RxExxx) transmits even pixels. PIN # SIGNAL NAME 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 RxOIN0RxOIN0+ RxOIN1RxOIN1+ RxOIN2RxOIN2+ VSS RxOCLKINRxOCLKIN+ RxOIN3RxOIN3+ RxEIN0RxEIN0+ VSS RxEIN1RxEIN1+ VSS RxEIN2RxEIN2+ RxECLKINRxECLKIN+ RxEIN3RxEIN3+ VSS VSS NC VSS VCC VCC VCC DESCRIPTION Negative LVDS differential data input (Odd data) Positive LVDS differential data input (Odd data) Negative LVDS differential data input (Odd data) Positive LVDS differential data input (Odd data) Negative LVDS differential data input (Odd data,H-Sync,V-Sync,DSPTMG) Positive LVDS differential data input (Odd data, H-Sync,V-Sync,DSPTMG) Power Ground Negative LVDS differential clock input (Odd clock) Positive LVDS differential clock input (Odd clock) Negative LVDS differential data input (Odd data) Positive LVDS differential data input (Odd data) Negative LVDS differential data input (Even data) Positive LVDS differential data input (Even data) Power Ground Positive LVDS differential data input (Even data) Negative LVDS differential data input (Even data) Power Ground Negative LVDS differential data input (Even data) Positive LVDS differential data input (Even data) Negative LVDS differential clock input (Even clock) Positive LVDS differential clock input (Even clock) Negative LVDS differential data input (Even data) Positive LVDS differential data input (Even data) Power Ground Power Ground No Connection ( for AUO test) Power Ground +5.0V Power Supply +5.0V Power Supply +5.0V Power Supply
Ver0.4
16/29
M170EG01 V.1
Note1: Start from left side
Connector
1 RxOIN0Note3: Please follow PSWG.
30 VCC
Ver0.4 17/29
Note2: Input signals of odd and even clock shall be the same timing.
M170EG01 V.1
The input data format:
Note1: Normally, DE, VS, HS on EVEN channel are not used. Note2: Please follow PSWG. Note3: 8-bit in
Ver0.4
18/29
M170EG01 V.1
Product Specification 3.5 Signal Electrical Characteristics

Each signal characteristics are as follows; Symbol VTH VTL VID VICM Parameter Differential Input High Threshold Differential Input Low Threshold Input Differential Voltage Differential Input Common Mode Voltage Min -100 100 1.1 Typ 400 Max 100 600 1.45 Units [mV] [mV] [mV] [V] VTH/VTL = 100Mv Condition VICM = 1.2V VICM = 1.2V Note Note Note Note
Note LVDS Signal Waveform VTH x VIDx VTL
VICM
VSS
3.6 Interface Timings 3.6.1 Timing Characteristics

Item Data CLK Period H-section Display Area Period V-section Display Area Frame Rate Note: DE mode only Symbol Tclk Th Tdisp(h) Tv Tdisp(v) F Min 40 685 640 1036 1024 49 Typ 54 844 640 1066 1024 60 Max 70 1024 640 2048 1024 75 Unit MHz Tclk Tclk Th Th Hz
Ver0.4
19/29
M170EG01 V.1
Product Specification 3.6.2 Timing Definition
DE
CLK DE
Tclk
Tblk(v)
Th
Tv
Tdisp(h) Th
Tdisp(v)
Tblk(h)
Ver0.4
20/29
M170EG01 V.1
Product Specification 3.7 Power Consumption

Input power specifications are as follows; Symbol VDD IDD Irush PDD VDDrp Parameter Logic/LCD Drive Voltage VDD current LCD Inrush Current VDD Power Allowable Logic/LCD Drive Ripple Voltage Min 4.5 Typ 5 1200 6 Max 5.5 1560 2.5 7.8 100 Units [Volt] [mA] [A] [Watt] [mV] p-p 10% Vin=5V , All Black Pattern, at 75Hz Note Vin=5V , All Black Pattern, at 75Hz Vin=5V , All Black Pattern, at 75Hz Condition
Note: Measurement conditions:

+5.0V D6 D5 D2 D1 R1 47K G Q3 AO6402 F1 S VCC
(LCD Module Input)

C1 1uF/16V
(High to Low) Control Signal

SW
D1 D2 D5 D6 R2 G 1K C3 Q3 AO6402 VR1 47K 0.01uF/25V S
+12.0V
C2 1uF/25V
90%
5.0V
10% 0V 470 us
Vin rising time
Ver0.4
21/29
M170EG01 V.1
3.8 Power ON/OFF Sequence

Vin and lamp power on/off sequence are as follows. The timing parameters of interface signal are shown in the table below. The signal please reference 3.4 Signal Description.
90%
90%
Vin
10% 0V T1 T2 T5 T6
10% 10%
T7
Signal 0V T3 T4
Lamp 0V
Symbol T1 T2 T3 T4 T5 T6 T7
Min. 0.5 0 200 100 0 1000
Values Typ. 16 -
Max. 10 10 50 10 -
Unit ms ms ms ms ms ms ms
Note: The values of the table are follow PSWG.
Ver0.4
22/29
M170EG01 V.1
4.0 Backlight Characteristics

4.1 Signal for Lamp connector
Connector No. CN1 Upper CN2 CN3 Lower CN4 Pin No. 1 2 1 2 1 2 1 2 Input Hot1 Cold1 Hot2 Cold2 Hot1 Cold1 Hot2 Cold2 Color Pink White Blue Black Pink White Blue Black Function High Voltage Low Voltage High Voltage Low Voltage High Voltage Low Voltage High Voltage Low Voltage
4.2 Parameter guideline for CCFL Inverter

Symbol ISCFL Parameter CCFL standard current Min. 7.0 Typ. 7.5 Max. 8.0 Unit [mA] rms IRCFL FCFL ViCFL (0 C) ViCF (25 C) VCFL CCFL Power consumption (for PCFL reference) LTCFL CCFL life Time 30,000 50,000 Note 1: CCFL standard current is measured at 25 2J . [Hour] (Ta=25oC) Note 4 19.8 21.8 [Watt]
o o
Condition (Ta=25oC) Note 1
CCFL operation range CCFL Frequency CCFL Ignition Voltage
3.0 40 1500
7.5 60 -
8.0 80 -
[mA] rms [KHz] [Volt] rms [Volt]
(Ta=25oC) (Ta=25oC) Note 2 (Ta=0oC)
(End of the lamp wire connector) CCFL Ignition Voltage 1150 (End of the lamp wire connector) CCFL Operation Voltage @7.5mA @3.0mA 660 700 -
(Ta=25oC)
rms [Volt] rms (Ta=25oC) Note 3 (Ta=25oC) Note 1
Note 2: CCFL Frequency should be carefully determined to avoid interference between inverter and TFT LCD Note 3: The variance of CCFL power consumption is 10%. Calculator value for reference (ICFLVCFL4=PCFL). Note 4: CCFL life time is determined as the time at which brightness of lamp is 50%. The typical life time of CCFL is on te condition at 7.5 mA lamp current.
Ver0.4
23/29
M170EG01 V.1
5.0 Vibration, Shock, and Drop

5.1 Vibration & Shock
Vibration Test Spec: Frequency: Sweep: Acceleration: Test method: Acceleration (G) Frequency (Hz) Active time (min) 1.5 10~200~10 30 10 - 200Hz 30 Minutes each Axis (X, Y, Z) 1.5G(10~200Hz P- P)
Shock Test Spec: Acceleration (G) a Active time -b Wave form Times 50 20 ms Half-sin 1
Direction: X , Y, Z
5.2 Drop test

Package test: The drop height is 60cm.
6.0 Environment
The display module will meet the provision of this specification during operating condition or after storage or shipment condition specified below. Operation at 10% beyond the specified range will not cause physical damage to the unit.
6.1 Temperature and Humidity 6.1.1 Operating Conditions

The display module operates error free, when operated under the following conditions; Temperature 0 0C to 50 0C Relative Humidity 8% to 95% Wet Bulb Temperature 39.0 0C
6.1.2 Shipping Conditions

The display module operates error free, after the following conditions; Temperature -20 0C to 60 0C Relative Humidity 5% to l00% Wet Bulb Temperature 39.0 0C
Ver0.4
24/29
M170EG01 V.1
Product Specification 6.2 Atmospheric Pressure

The display assembly is capable of being operated without affecting its operations over the pressure range as following specified; Pressure Maximum Pressure Minimum Pressure 1040hPa 674hPa Note (sea level) (3048m)
6.3 Thermal Shock

The display module will not sustain damage after being subjected to 100 cycles of rapid temperature change. A cycle of rapid temperature change consists of varying the temperature from -200C to 600C, and back again. Thermal shock cycle -20 0C for 30min 60 0C for 30min
Power is not applied during the test. After temperature cycling, the unit is placed in normal room ambient for at least 4 hours before powering on.
7.0 Reliability
This display module and the packaging of that will comply following standards.
7.1 Failure Criteria

The display assembly will be considered as failing unit when it no longer meets any of the requirements stated in this specification. Only as for maximum white luminance, following criteria is applicable. Maximum white Luminance shall be 150cd/m2 or more.
7.2 Failure Rate

The average failure rate of the display module (from first power-on cycle till 1,000 hours later) will not exceed 1.0%. The average failure rate of the display module from 1,000 hours until 16,000 hours will not exceed 0.7% per 1000 hours.
7.2.1 Usage
The assumed usage for the above criteria is: 220 power-on hours per month 500 power on/off cycles per month Maximum brightness setting Operation to be within office environment (250C typical)
Ver0.4
25/29
M170EG01 V.1
8.0 Safety
8.1 Sharp Edge Requirements
There will be no sharp edges or comers on the display assembly that could cause injury.
8.2 Materials 8.2.1 Toxicity

There will be no carcinogenic materials used anywhere in the display module. If toxic materials are used, they will be reviewed and approved by the responsible ADT Toxicologist.
8.2.2 Flammability
All components including electrical components that do not meet the flammability grade UL94-V1 in the module will complete the flammability rating exception approval process.
The printed circuit board will be made from material rated 94-V1 or better. The actual UL flammability rating will be printed on the printed circuit board.
8.3 Capacitors
If any polarized capacitors are used in the display assembly, provisions will be made to keep them from being inserted backwards.
Ver0.4
26/29
M170EG01 V.1
9.0 Other requirement

9.1 National Test Lab Requirement
The display module will satisfy all requirements for compliance to UL 1950, First Edition CSA C22.2 No.950-M89 EEC 950 EN 60 950 U.S.A. Information Technology Equipment Canada, Information Technology Equipment International, Information Technology Equipment International, Information Processing Equipment (European Norm for IEC950)
9.2 Label
The label is on the panel as shown below:
Ver0.4
27/29
10.0 Mechanical Characteristics
Ver0.4
28/29
Ver0.4
29/29
Approval
To Date
: LiteOn(HP) : 2004-01-27
SAMSUNG TFT-LCD
MODEL NO. : LTM170EU-L11
Approved by :
Any Modification of Spec is not allowed without SEC's permission.
Senior Manager :
PREPARED BY : AMLCD Technical Customer Service Team
Samsung Electronics Co . , LTD.
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
1 / 34
Approval
Contents
Revision History General Description 1. Absolute Maximum Ratings 1.1 Absolute ratings of environment 1.2 Electrical Absolute Ratings 2. Optical Characteristics 3. Electrical Characteristics 3.1 TFT LCD Module 3.2 Back-light Unit 4. Block Diagram 4.1 TFT LCD Module 4.2 Back-light Unit 5. Input 5.1 5.2 5.3 5.4 -------------------------- (3) -------------------------- (4) -------------------------- (5)
-------------------------- (7) -------------------------- (14)
-------------------------- (17)
Terminal Pin Assignment -------------------------- (18) Input Signal & Power LVDS Interface Back-light Unit Input Signals, Basic Display Colors and Gray Scale of Each Color
6. Interface Timing -------------------------- (23) 6.1 Timing Parameters (DE only mode) 6.2 Timing Diagrams of Interface Signal (DE only mode) 6.3 Power ON/OFF Sequence 7. Outline Dimension 8. Reliability Test 9. Packing 10. Marking & Others 11. Inspection Criteria 12. General Precaution 12.1 Handling 12.2 Storage 12.3 Operation 12.4 Others -------------------------- (26) -------------------------- (28) -------------------------- (29) -------------------------- (30) -------------------------- (32) -------------------------- (33)
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
2 / 34
* Revision History
Date
Jan. 27, 2004
Approval
Summary
Approval specification of LTM170EU-L11 model for LiteOn was issued first.
Rev. No
000
Page
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
3 / 34
General Description
* Description
Approval
LTM170EU-L11 is a color active matrix TFT (Thin Film Transistor) liquid crystal display (LCD) that uses amorphous silicon TFTs as switching devices. This model is composed of a TFT LCD panel, a driver circuit and a back-light system. The resolution of a 17.0" contains 1280 x 1024 pixels and can display up to 16.2 millions colors.
* Features - High contrast ratio, high aperture structure - TN (Twisted Nematic) mode Wide viewing angle High speed response SXGA (1280 x 1024 pixels) resolution Low power consumption 2 dual CCFTs (Cold Cathode Fluorescent Tube) DE (Data Enable) mode LVDS (Low Voltage Differential Signaling) interface (2pixel/clock) Compact Size Design
* Applications Workstation & desktop monitors Display terminals for AV application products Monitors for industrial machine
* General information Items Display area Driver element Display colors Color Gamut Number of pixels Pixel arrangement Pixel pitch Display mode Surface treatment Specification 337.92(H) x 270.336(V) a-Si TFT active matrix 16.2M 70.8 (Based on sRGB) 1280 x 1024 RGB vertical stripe 0.264(H) x 0.264(W) Normally White Haze 25% , Hard-coating (3H) Unit mm colors % pixel mm Anti-glare Note
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
4 / 34
Approval
* Mechanical information Item Module size Horizontal(H) Vertical(V) Depth(D) Weight Min. 358.0 296.0 Typ. 358.5 296.5 Max. 359.0 297.0 17.5 2,100 Note mm mm mm g
1. Absolute Maximum Ratings

1.1 Absolute ratings of environment Item Storage temperature Operating temperature (Glass surface temperature) Shock ( non - operating ) Vibration ( non - operating ) Symbol TSTG TOPR Snop Vnop Min. -25 0 Max. 60 50 50 1.5 Unit G G Note (1) (1) (2),(4) (3),(4)
Note (1) Temperature and relative humidity range are shown in the figure below. 90 % RH Max. ( 40 C Ta ) Maximum wet-bulb temperature at 39 C or less. (Ta > 40 C) No condensation. (2) 11ms, sine wave, one time for X, Y, Z axis (3) 10-300 Hz, Sweep rate 10min, 30min for X,Y,Z axis (4) At vibration and shock test, the fixture which holds the module to be tested has to be hard and rigid enough so that the module would not be twisted or bent by the fixture. Relative Humidity ( %RH)
90
100 80 60 40 20
( 40, 90 )
Operating Range
( 50, 50.4 ) ( 60,27.7)
( 25,5) (-25,5)
-40 -20 0
Storage Range
0 20 40 60 80
Temperature
(OC)
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
5 / 34
Approval
1.2 ELECTRICAL Item Power Supply Voltage Note (1) ABSOLUTE RATINGS (Vss = GND = 0 V) Symbol VDD Min. Vss-0.5 Max. 6.5 Unit V Note (1) (1) TFT LCD Module
Within Ta ( 25 2 C)
(2) BACK-LIGHT UNIT Item Lamp Current Lamp Frequency Note (1) Symbol IL fL Min. 2.0 40 Max. 7.0 80 Unit. mArms kHz
(Ta = 25 2 C)
Note (1),(2) (1)
Permanent damage to the device may occur if maximum values are exceeded. Functional operation should be restricted to the conditions described under Normal Operating Conditions. (2) Specified values are for a single lamp. (Refer to the Note (1) in the page 16 for further information).
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
6 / 34
2. Optical Characteristics
Approval
The following items are measured under stable conditions. The optical characteristics should be measured in a dark room or equivalent state with the methods shown in Note (1). Measuring equipment : TOPCON BM-5A, BM-7, Eldim EZ-Contrast
* Ta = 25 2 C, VDD=5V,
PHOTO RESEARCH PR650
(Inverter Freq. : 50kHz)
fv= 60Hz, fDCLK=54MHz, IL = 6.5mArms
Item Contrast Ratio (Center of screen) Response Time Rising Falling
Symbol C/R Tr Tf YL Rx Ry Gx Gy Bx By Wx Wy L R H L Buni LR DSHA F
Condition
Min. 400 -
Typ. 500 3 10 300 0.650 0.330 0.300 0.600 0.150 0.080 0.313 0.329 75 75 75 60 -
Max. 5 13 0.680 0.360 0.330 0.630 0.180 0.110 0.343 0.359 25 1.7 2 8
Unit
Note (3) BM-5A
msec cd/m2
(5) BM-7 (6) BM-5A
Luminance of White (Center of screen) Red Green Blue White Hor. Ver.
Normal = 0 = 0 Viewing Angle
250 0.620 0.300 0.270 0.570 0.120 0.050 0.283 0.299 65 65 65 50 -
Color Chromaticity (CIE 1931)
(7) PR650
Viewing Angle
CR 10
Degrees
(8) BM-5A
Brightness Uniformity (9 Points) Luminance Uniformity(TCO'99) Cross Modulation Flicker
(4) BM-5A (9)
(10) BM-5A (11) BM-7
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
7 / 34
Note (1) Test Equipment The measurement 30min and 40min of the back-light.
Setup should be executed in a stable, windless and dark room between after lighting the back-light at the given temperature for stabilization This should be measured in the center of screen.
Approval
Single lamp current : 6.5mA (Refer to the note(1) in the page 16 for more information.) Environment condition : Ta = 25 2 C
Photodetector Photodetector BM-5A BM-7 PR650 Field 2 2 1 BM-5A : 40 BM-7 TFT - LCD Module LCD Panel : 50 PR650 : 50 Field
The center of the screen
Optical Measuring Equipment Setup
Note (2) Definition of test point

128
9
640
8
1152
7
Active AREA 102
512
922
: test point
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
8 / 34
Note (3) Definition of Contrast Ratio (C/R) : Ratio of gray max (Gmax) & gray min (Gmin) at the center point of the panel CR = G max G min
Approval
Gmax : Luminance with all pixels white Gmin : Luminance with all pixels black
Note (4) Definition of 9 points brightness uniformity ( B max B min) B max
Buni = 100
Bmax : Maximum brightness Bmin : Minimum brightness
Note (5) Definition of Response time : Sum of Tr, Tf

Display data Optical Instruments Response 100% 90%
WHITE(data off)
BLACK(data on)
WHITE(data off)
TR
TF
10% 0% TIME
Note (6) Definition of Luminance of White : Luminance of white at center point. Note (7) Definition of Color Chromaticity (CIE 1931) Color coordinate of Red, Green, Blue & White at center point.
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
9 / 34
Note (8) Definition of Viewing Angle :
Viewing angle range (CR 10 )
Approval
N o rm a l L in e = 0o = 0o ,
L R L
= 9 0o
1 2 O c lo c k d ire c tio n H = 9 0o
6 O c lo c k y d ire c tio n L= 9 0o
x
R = 9 0o
Note (9) TCO' 99 Certification Requirements and test methods for Flat Panel Visual Display Units(VDUs) ( 1.5.2 Luminance Uniformity)
LR = ((Lmax,+30deg. / Lmin,+30deg.) + (Lmax,-30deg. / Lmin,-30deg.)) / 2
Note (10) Definition of Cross Modulation (Crosstalk : DSHA)

YA YB YA
Crosstalk Modulation Ratio(D SHA ) =
100 (%)
Where YA = luminance with moving a black bar, YB = luminance without moving a black bar - Mesurement angle = 2 Viewing angle, Measurement area = 12 and Background pattern (except for Black bar) includes Gray 1 ~ 63
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
10 / 34
a. Measurement procedure of Horizontal Crosstalk
Approval
L 2L/3
YA1
18mm Shift
Darkest Pattern H H/2 (Gray 0)
YB1
YB2
18mm Shift
YA2
b. Measurement procedure of Vertical Crosstalk
L L/2
18mm Shift
Darkest Pattern H
2H/3
YA1
(Gray 0) 18mm shift
YB1
YB2
YA2
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
11 / 34
Approval
Note (11) Flicker level should be measured with 1 by 1 sub-checker pattern. Definition of Flicker level Flicker level = 1000 * (A-B) where,
(
A=
10
10
0.8558-0.000401<log(L(0Hz+30Hz))>+0.86
) L(0Hz +30Hz)
2
0.74
0.8558-0.000401<log(L(0Hz+30Hz))>+0.86
) L(0Hz +30Hz)
2
0.74
0.74
+1584.9
(
B= 10
10
0.8558-0.000401<log(L(0Hz+30Hz))>+0.86
) L(0Hz - 30Hz)
2
0.74
0.8558-0.000401<log(L(0Hz+30Hz))>+0.86
(
where,
) L(0Hz - 30Hz)
2
0.74
0.74
+1584.9
0Hz(dB)+b
30Hz(dB)+b
L(0Hz +30Hz) =
( 10
20
+
20
10
20
)/a
0Hz(dB)-b
30Hz(dB)-b
L(0Hz - 30Hz) =
10
20
10
)/a
where a = Proportion Constant of Input brightness to BM-7 and output voltage (V*(/cd)) b = Standard voltage which is proposed to calculate the input voltage to DSA (Dynamic signal analyzer) in DB scale ( Vref = 10
b/20
One maximum value of three estimated values Test pattern : For 1-dot inversion driving (Grey levels of foreground dots on the test panel are G22, G32, G45) Test point :5 points of the display area
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
12 / 34
a. test pattern : 1 by 1 sub-checker pattern
Approval
BackgroundBackGround ForeGround Foreground
b. test point
213
5
640
1067
4
Active AREA 170
512
854
: test point
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
13 / 34
3. Electrical Characteristics
3.1 TFT LCD MODULE
Approval
Ta = 25 C Symbol VDD LVDS IDD fV fH fDCLK IRUSH Min. 4.5 Typ. 5.0 Max. 5.5 DS90C386 850 77 82.082 69.28 3.0 Unit V Pair mA mA mA Hz kHz MHz A (4) Note (1)
Item Voltage of Power Supply Interface type Current of (a) Black Power (b) White Supply (c) Dot Vsync Frequency Hsync Frequency Main Frequency Rush Current
DS90C383/385 600 500 700 55 56.7 40 60 64 54 -
(2),(3)
Note (1) The connector for display data & timing signal should be connected.(Vss=0V) VDD = 5.0V, DC Current. (2) fV=60Hz, fDCLK = 54MHz, (3) Power dissipation check pattern(LCD Module only) a) Black Pattern b) White Pattern
c) Dot Pattern
RGBRGB RGBR RGBRGB RGB RGB RGBR B RGBRGBRGB RGB RGBRGR GBRGBRGB RGBRGBRGB RG RGBRGBRGB RGB RGBR RGB RGBRGBRG
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
14 / 34
(4) Measurement Conditions

5V
Approval
M1 2SK1059
VDD ( LCD
FUSE C1 1uF
INPUT)
R1 47K R2 1K M2 2SK1399
CONTROL SIGNAL
(HIGH to LOW)
14V 12V
R3 C3 1uF 47K
C2
10000pF
Control Signal : High(+5V) Low(Ground) All Signal lines to panel, except for power 5V : Ground The rising time of supplied voltage is controlled to 470us by R3 and C2 value.
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
15 / 34
3.2 BACK-LIGHT UNIT The back-light system is an edge - lighting type with 2 dual CCFTs ( Cold Cathode Fluorescent Tube ) The characteristics of two dual lamps are shown in the following tables. Ta=25 2 C Item Lamp Current Lamp Voltage Lamp Frequency Operating Life Time Startup Voltage
Note)
Approval
Symbol IL VL fL Hr Vs
Min. 2.5 50 50,000 -
Typ. 6.5 650 -
Max. 7.0 60 0 : 1,800 25: 1,500
Unit mArms Vrms kHz Hour Vrms
Note (1) (2) (3) (4)
The wave form of the inverter output voltage must be area symmetric and the design of the inverter must have specifications for the modularized lamp. l
The performance of the back-light, for example life time or brightness, is much influenced by the characteristics of the DC-AC inverter for the lamp. So all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. When you design or order the inverter, please make sure that a poor lighting caused by the mismatch of the back-light and the inverter(poor lighting, flicker, etc.) never occur. When you confirm it, the module should be operated in the same condition as it is installed in your instrument. Note (1) Lamp current is measured with current meter for high frequency as shown below. Refer to the block diagram of the back-light unit in the next page for more information. Specified values are for a single lamp.
HOT(PINK) COLD(WHITE)
LCD Module
HOT(BLUE) COLD(BLACK)
Inverter (SK1700A)
HOT(PINK) COLD(WHITE) HOT(BLUE) COLD(BLACK)
(2) Lamp frequency which may produce interference with horizontal synchronous frequency may cause line flow on the display. Therefore lamp frequency should be detached from the horizontal synchronous frequency and its harmonics as far as possible in order to avoid interference. (3) Life time (Hr) of a lamp is defined as the time in which it continues to operate under the condition of Ta = 252C and IL = 6.5mArms for a lamp until the brightness becomes 50% or lower than it's original value. Operating condition is lamp unit itself, not module assembly at operating current 6.5mA. (4) If an inverter has shutdown function, it should keep its output for over 1 second even if the lamp connector is open. Otherwise the lamps may not be turned on. (5) Because the inverter uses high voltage, please disconnect it from the power before assembling or disassembling.
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
16 / 34
4. Block Diagram
4.1 TFT LCD MODULE
Approval
Input Connector (30P) DC/DC Converter
L-TCON (LVDS & Timing Controller)
RSDS Signal
Source Drive IC (x10ea) (RSDS)
DC/DC Converter
Vcom Generator Gate Drive IC (x4ea)
TFT-LCD PANEL
Viedo Data Control Signal Gamma Vcom DVdd AVdd Von/Voff
Gamma Generator
4.2
BACK-LIGHT UNIT
Connector : JST BHSR-02VS-1 or equivalent
LAMP(CCFL)
1 2 3 4
LAMP(CCFL)
LAMP(CCFL)
1 2 3 4
LAMP(CCFL)
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
17 / 34
5. Input Terminal Pin Assignment

5.1. Input Signal & Power ( Connector : FI-XB30SSL-HF15 or equivalent )
PIN NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 SYMBOL VDD VDD VDD NC NC NC GND RXE3+ RXE3RXEC+ RXECRXE2+ RXE2GND RXE1+ RXE1GND RXE0+ RXE0RXO3+ RXO3RXOC+ RXOCGND RXO2+ RXO2RXO1+ RXO1RXO0+ RXO0No Connection No Connection No Connection Power Ground Power Supply : +5V FUNCTION
Approval
Positive Transmission Data of Pixel 3 (EVEN data) Negative Transmission Data of Pixel 3 (EVEN data) Positive Sampling Clock (EVEN data) Negative Sampling Clock (EVEN data) Positive Transmission Data of Pixel 2 (EVEN data) Negative Transmission Data of Pixel 2 (EVEN data) Power Ground Positive Transmission Data of Pixel 1 (EVEN data) Negative Transmission Data of Pixel 1 (EVEN data) Power Ground Positive Transmission Data of Pixel 0 (EVEN data) Negative Transmission Data of Pixel 0 (EVEN data) Positive Transmission Data of Pixel 3 (ODD data) Negative Transmission Data of Pixel 3 (ODD data) Positive Sampling Clock (ODD data) Negative Sampling Clock (ODD data) Power Ground Positive Transmission Data of Pixel 2 (ODD data) Negative Transmission Data of Pixel 2 (ODD data) Positive Transmission Data of Pixel 1 (ODD data) Negative Transmission Data of Pixel 1 (ODD data) Positive Transmission Data of Pixel 0 (ODD data) Negative Transmission Data of Pixel 0 (ODD data)
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
18 / 34
5.2
LVDS Interface
Approval
5.2.1 Odd pixel data (1st pixel data)

1st LVDS Transmitter ( DS90C383, DS90C385 ) Signal Interface Device Input Pin No 51 52 54 55 56 2 3 4 6 7 8 10 11 12 14 15 16 18 19 20 22 23 24 50 Symbol TXIN0 TXIN1 TXIN2 TXIN3 TXIN4 TXIN5 TXIN6 TXIN7 TXIN8 TXIN9 TXIN10 TXIN11 TXIN12 TXIN13 TXIN14 TXIN15 TXIN16 TXIN17 TXIN18 TXIN19 TXIN20 TXIN21 TXIN22 TXIN27 Symbol RO0 RO1 RO2 RO3 RO4 RO7 RO5 GO0 GO1 GO2 GO6 GO7 GO3 GO4 GO5 BO0 BO6 BO7 BO1 BO2 BO3 BO4 BO5 RO6 Device Input Signal Function Red Odd Pixel Data (LSB) Red Odd Pixel Data Red Odd Pixel Data Red Odd Pixel Data Red Odd Pixel Data Red Odd Pixel Data (MSB) Red Odd Pixel Data Green Odd Pixel Data (LSB) Green Odd Pixel Data Green Odd Pixel Data Green Odd Pixel Data Green Odd Pixel Data (MSB) Green Odd Pixel Data Green Odd Pixel Data Green Odd Pixel Data Blue Odd Pixel Data (LSB) Blue Odd Pixel Data Blue Odd Pixel Data (MSB) Blue Odd Pixel Data Blue Odd Pixel Data Blue Odd Pixel Data Blue Odd Pixel Data Blue Odd Pixel Data Red Odd Pixel Data TXOUT3TXOUT3+ No. 10 No. 11 RXO3RXO3+ TXOUT2TXOUT2+ No. 5 No. 6 RXO2RXO2+ TXOUT3TXOUT3+ TXOUT1TXOUT1+ No. 10 No. 11 No. 3 No. 4 RXO3RXO3+ RXO1RXO1+ TXOUT1TXOUT1+ No. 3 No. 4 RXO1RXO1+ TXOUT3TXOUT3+ TXOUT0TXOUT0+ TXOUT1TXOUT1+ TXOUT3TXOUT3+ No. 10 No. 11 No. 1 No. 2 No. 3 No. 4 No. 10 No. 11 RXO3RXO3+ RXO0RXO0+ RXO1RXO1+ RXO3RXO3+ TXOUT0TXOUT0+ No. 1 No. 2 RXO0RXO0+ Output Signal To LTM170EU Interface ( CN101 ) Terminal Symbol
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
19 / 34
Approval
5.2.2 Even pixel data (2nd pixel data)
2nd LVDS Transmitter ( DS90C383, DS90C385 ) Signal Interface Device Input Pin No 51 52 54 55 56 2 3 4 6 7 8 10 11 12 14 15 16 18 19 20 22 23 24 50 Symbol TXIN0 TXIN1 TXIN2 TXIN3 TXIN4 TXIN5 TXIN6 TXIN7 TXIN8 TXIN9 TXIN10 TXIN11 TXIN12 TXIN13 TXIN14 TXIN15 TXIN16 TXIN17 TXIN18 TXIN19 TXIN20 TXIN21 TXIN22 TXIN27 Symbol RE0 RE1 RE2 RE3 RE4 RE7 RE5 GE0 GE1 GE2 GE6 GE7 GE3 GE4 GE5 BE0 BE6 BE7 BE1 BE2 BE3 BE4 BE5 RE6 Device Input Signal Function Red Even Pixel Data (LSB) Red Even Pixel Data Red Even Pixel Data Red Even Pixel Data Red Even Pixel Data Red Even Pixel Data (MSB) Red Even Pixel Data Green Even Pixel Data (LSB) Green Even Pixel Data Green Even Pixel Data Green Even Pixel Data Green Even Pixel Data (MSB) Green Even Pixel Data Green Even Pixel Data Green Even Pixel Data Blue Even Pixel Data (LSB) Blue Even Pixel Data Blue Even Pixel Data (MSB) Blue Even Pixel Data Blue Even Pixel Data Blue Even Pixel Data Blue Even Pixel Data Blue Even Pixel Data Red Even Pixel Data TXOUT3TXOUT3+ No. 22 No. 23 RXE3RXE3+ TXOUT2TXOUT2+ No. 18 No. 19 RXE2RXE2+ TXOUT3TXOUT3+ TXOUT1TXOUT1+ No. 22 No. 23 No. 15 No. 16 RXE3RXE3+ RXE1RXE1+ TXOUT1TXOUT1+ No. 15 No. 16 RXE1RXE1+ TXOUT3TXOUT3+ TXOUT0TXOUT0+ TXOUT1TXOUT1+ TXOUT3TXOUT3+ No. 22 No. 23 No. 12 No. 13 No. 15 No. 16 No. 22 No. 23 RXE3RXE3+ RXE0RXE0+ RXE1RXE1+ RXE3RXE3+ TXOUT0TXOUT0+ No. 12 No. 13 RXE0RXE0+ Output Signal To LTM170EU Interface ( CN101 ) Terminal Symbol
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
20 / 34
5.3
BACK-LIGHT UNIT Pin No. 1 2 3 4 1 2 3 4 Connector Part No. Input Hot1 Cold1 Hot2 Cold2 Hot1 Cold1 Hot2 Cold2 Color Pink White Blue Black Pink White Blue Black
Approval
Function High Voltage Ground High Voltage Ground High Voltage Ground High Voltage Ground
Upper
Lower
JST BHSR-02VS-1 or equivalent
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
21 / 34
5.4 Input Signals, Basic Display Colors and Gray Scale of

DISPLAY (8bit) BLACK BLUE GREEN BASIC COLOR CYAN RED MAGENTA YELLOW WHITE BLACK DARK GRAY SCALE OF RED LIGHT RED BLACK DARK GRAY SCALE OF GREEN LIGHT GREEN BLACK DARK GRAY SCALE OF BLUE LIGHT BLUE 0 0 0 0 1 1 1 1 0 1 0 : : 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 1 1 1 1 0 0 1 : : 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 1 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 RED 0 0 0 0 1 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 1 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 1 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 : : 0 0 0 0 1 0 : : 1 0 1 0 0 0 : : 0 0 0 0 0 1 1 0 0 1 1 0 0 0 : : 0 0 0 0 0 1 : : 0 1 1 0 0 0 : : 0 0 0 0 0 1 1 0 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 DATA SIGNAL GREEN 0 0 1 1 0 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 1 1 0 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 1 1 0 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 0 1 1 0 0 1 1 0 0 0
Each Colors
Approval
GRAY BLUE SCALE LEVEL R0 R1 R2 R3~ R252 0 0 0 0 0 0 0 0 0 0 0 0 R252 R252 R252 G0 G1 G2 G3~ G252 0 0 0 0 0 0 0 0 0 0 0 0 G252 G252 G252 B0 B1 B2 B3~ B252 1 1 1 1 1 1 B252 B252 B252
COLOR
R0 R1 R2 R3 R4 R5 R6 R7 G0 G1 G2 G3 G4 G5 G6 G7 B0 B1 B2 B3 B4 B5 B6 B7 0 0 1 1 0 0 1 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 : : 1 1 1 0 0 0 0 0 0 0 1 0 : : 0 0 0 1 0 1 0 1 0 1 0 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 1 : : 0 1 1 0 1 0 1 0 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 1 0 1 0 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 1 0 1 0 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 1 0 1 0 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0
Note)
Definition of Gray : Rn : Red Gray, Gn : Green Gray, Bn : Blue Gray (n = Gray level) Input Signal : 0 = Low level voltage, 1 = High level voltage
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
22 / 34
6. Interface Timing
6.1 Timing Parameters
SIGNAL
Approval
( DE only mode )
SYMBOL 1/TC TCH TCL TDS TDH TES MIN. 40 4 4 4 4 4 18.2 Cycle Tv 1031 1066 60 1024 844 640 77 1024 1130 640 lines Hz lines lines clocks clocks (3) TYP. 54 16.7 MAX. 69.28 12.99 UNIT MHz nsec nsec (1), (2) nsec nsec nsec msec NOTE ITEM
Frequency Clock High Time Low Time Setup Time Data Hold Time Data Enable Setup Time
Frame Frequency Frequency Vertical Active Display Term One Line Scanning Time Horizontal Active Display Term Display Period Vertical Blank Period Cycle Display Period 1/Tv TVD TVB TH THD
55 1024 8 752 640
Note (1) Test Point : TTL control signal and CLK at LVDS Tx input terminal in system (2) Internal Vcc = 3.3V (3) At low Vsync frequency, Under 60Hz, flicker level can increase at specific pattern.
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
23 / 34
6.2
Timing diagrams of interface signal ( DE only mode )
Approval
TV TVD TVB
DE
TH THD
DE
DCLK
TC
DATA SIGNALS
TC TCH TCL
DCLK
TDS TDH
0.5 VCC
DISPLAY DATA
TES
0.5 VCC
DE
0.5 VCC
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
24 / 34
6.3 Power ON/OFF Sequence
Approval
To prevent a latch-up or DC operation of the LCD module, the power on/off sequence should be as the diagram below.
0.9 VDD 0V 0.1 VDD 0.9 VDD 0.1 VDD
Power Supply VDD
300 T1 10msec 0 T2 50 msec 0 T3 50 msec 1sec T 4 Signals
T1 T2
VALID
T3 T4
0V Power On Power Off
Back-light(Recommended) 500 msec T5 100 msec T 6 T5
50%
50%
T6
Power ON/OFF Sequence
Note. (1) The supply voltage of the external system for the module input should be the same as the definition of VDD. (2) Apply the lamp voltage within the LCD operation range. When the back-light turns on before the LCD operation or the LCD turns off before the back-light turns off, the display may momentarily show abnormal screen. (3) In case of VDD = off level, please keep the level of input signals low or keep a high impedance. (4) T4 should be measured after the module has been fully discharged between power off and on period. (5) Interface signal should not be kept at high impedance when the power is on.
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
25 / 34
7. Outline Dimension
[ Refer to the next page ]
Approval
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
26 / 34
8. Reliability Test
Test Items HTOL* LTOL* THB** HTS*** LTS*** Thermal Cycle Box Drop Shock (Non-operating) Vibration (Non-operating) ESD (Non-Operating) Conditions 50C, Bias 0C, Bias 40C / 95% , Bias 70C, No Bias -30C, No Bias -20C/30min ~ +60C/30min , No bias 1 angle, 3 edge, 6 side, 66 cm 50G, 11msec Sine wave, x/y/z axis 1.5G, 10~300 Hz x/y/z axis, sweep rate : 10 min contact : 150pF, 330 ohm, 9point Air(non-contact) : 150pF, 330 ohm, 9point CDM : 150pF, 330 ohm, 9point 1 time/axis 30min/axis 10kV 20kV 10kV Time/Cycle 500 hrs 500 hrs 500 hrs 500 hrs 500 hrs 100 cycle
Approval
Sample 12 5 5 5 5 5 5 3 3 3 3 3
[ Result Evaluation Criteria] Under the display quality test conditions with normal operation state, these should be no change which may affect practical display functions.
* HTOL/ LTOL : High/Low Temperature Operating Life, ** THB : Temperature Humidity Bias *** HTS/LTS : High/Low Temperature Storage
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
28 / 34
9. PACKING
9.1 CARTON (Internal Package) (1) Packing Form Corrugated fiberboard box and corrugated cardboard as shock absorber (2) Packing Method a) without inverter
Approval
SHIELDING-BAG
PANEL-PROTECTOR
TAPE-PAPER(4point) CUSHION-PAD PACKING-CASE
LABEL-SAFETY
LABEL
OPP-TAPE
NOTE) 1) TOTAL Weight : Approx.
10
2) Acceptance number of piling : 5 sets 3) Carton size : 390(W) X 320(D) X 410(H) 4) MAX accumulation quantity : 5 cartons
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
29 / 34
(3) Packing Material

No 1 2 3 4 Part name Static electric protective sack Packing case(Inner box) included shock absorber Pictorial marking Carton Quality 5 1 set 2 pcs 1 set
Approval
10. MARKING & OTHERS

A nameplate bearing followed by is affixed to a shipped product at the specified location on each product. (1) Parts number (2) Revision code (3) Customer code X XX : LTM170EU-L11 : Two letters : One letter
Revision Code Customer Code
(4) Lot number
5 E 3 G 00210A
Lot Number Month Year Device Line
(5) Nameplate Indication
LTM170EU-L01 LTM170EU-L11 Week Code

Lot Number
Week Code: 00 00 40 mm
Week Year
XXX 000
80 mm
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
30 / 34
Approval
(6) Packing box attach
80mm Parts number Revision CODE
LTM170EU-L11 000 5 L532603333
BOX SERIAL Number
40mm
(7) Others 1. After service part

Part Name ASS'Y-LAMP(U) ASS'Y-LAMP(L) Description LTM170EU, D2.4, L349, 2PIN2 LTM170EU, D2.4, L349, 2PIN2
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
31 / 34
11.
Inspection Criteria
Approval
When products are shipped, incoming inspection should be carried out with a sampling inspection based on MIL-STD-105E level II by AQL 1.0%. CHANGE CONTROL Design of the product may be changed regarding the specifications, appearance, parts used, circuits, etc. for product improvement. If a design change is judged to affect the specifications of this product, supplier should inform customer of the change in advance. QUALITY CONTROL In the event of a product failure under normal operating conditions, a product trouble or a functional disorder that can be deemed to be the responsibility of supplier, supplier should repair the fault or replace the product free of charge within one year from the product delivery date. However, supplier does not take responsibility for the product quality in the case of modifications not specified by supplier. MAINTENANCE The specifications of the functions of maintenance parts may be partially changed within the range which provides equivalent or better quality. In principle, maintenance parts should be product units. When stopping manufacturing this product, supplier should notify customer in advance. HANDLING OF DOUBTFUL POINTS Any doubt not stipulated in this specification is to be resolved by mutual agreement between customer and supplier, and supplier should make efforts for improvement in good faith.
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
32 / 34
12.
General Precautions
Approval
12.1 Handling (a) When the module is assembled, it should be attached to the system firmly using all mounting holes. Be careful not to twist and bend the module. (b) Because the inverter use high voltage, it should be disconnected from power before it is assembled or disassembled. (c) Refrain from strong mechanical shock and / or any force to the module. In addition to damage, this may cause improper operation or damage to the module and CCFT back-light. (d) Note that polarizers are very fragile and could be damage deasily. Do not press or scratch the surface harder than a HB pencil lead. (e) Wipe off water droplets or oil immediately. If you leave the droplets for a long time, staining or discoloration may occur. (f) If the surface of the polarizer is dirty, clean it using some absorbent cotton or soft cloth. (g) Desirable cleaners are water, IPA(Isopropyl Alcohol) or Hexane. Do not use Ketone type materials(ex. Acetone), Ethyl alcohol, Toluene, Ethyl acid or Methyl chloride. It might permanent damage to the polarizer due to chemical reaction. (h) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth . In case of contact with hands, legs or clothes, it must be washed away with soap thoroughly. (i) Protect the module from static, or the CMOS Gate Array IC would be damaged. (j) Use finger-stalls with soft gloves in order to keep display clean during the incoming inspection and assembly process. (k) Do not disassemble the module. (l) Do not pull or fold the lamp wire. (m) Do not adjust the variable resistor located on the module. (n) Protection film for polarizer on the module should be slowly peeled off just before use so that the electrostatic charge can be minimized. (o) Pins of I/F connector should not be touched directly with bare hands.
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
33 / 34
12.2 Storage
Approval
(a) Do not leave the module in high temperature, and high humidity for a long time. It is highly recommended to store the module with temperature from 0 to 35 and relative humidity of less than 70%. (b) Do not store the TFT-LCD module in direct sunlight. (c) The module should be stored in a dark place. It is prohibited to apply sunlight or fluorescent light in storing. 12.3 Operation (a) Do not connect or disconnect the module in the "Power On" condition. (b) Power supply should always be turned on/off "Power on/off sequence" by the item 6.3
(c) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference should be done by system manufacturers. Grounding and shielding methods may be important to minimize the interference. (d) The cable between the back-light connector and its inverter power supply should be connected directly with a minimized length. A longer cable between the back-light and the inverter may cause lower luminance of lamp(CCFT) and may require higher startup voltage(Vs). 12.4 Others (a) Ultra-violet ray filter is necessary for outdoor operation. (b) Avoid condensation of water. It may result in improper operation or disconnection of electrode. (c) Do not exceed the absolute maximum rating value. ( supply voltage variation, input voltage variation, variation in part contents and environmental temperature, and so on) Otherwise the module may be damaged. (d) If the module keeps displaying the same pattern for a long period of time, the image may be "sticked" to the screen. (e) This module has its circuitry PCB's on the rear side and should be handled carefully in order not to be stressed.
Doc . No
LTM170EU-L11
Rev.No
03-000-S-040127
Page
34 / 34

Acer Al1715p SM

Uploaded by

Document Informationclick to expand document informationAcer AL1715p is an existing model (AL1715) with AU and Samsung panel. The only difference is that the later employs AU and Samsung panel. Information in this guide is subject to change without notice.

Document Informationclick to expand document information

Copyright:

Available Formats

Acer Al1715p SM

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Acer Al1715p SM

Uploaded by

Copyright:

Available Formats

Acer AL1715p Service Guide

WARNING: (FOR FCC CERTIFIED MODELS)

SPECIAL NOTES ON LCD MONITORS

Comparison Chart of AR577/578 AR577

Support Color Temp user adjust

DDC2B NO NO No Not support Yes / No Option

LCD monitor General specification

Display size: Display mode:

1280 1024 (60/70/75 Hz) standard resolution

Luminance Uniformity: Pc interface:

15 pin Mini D type, (standard VGA video)

Total output power:

LCD Panel Specification

IL = 6.5mA (RMS) ITEM

FDCLK = 54MHz TYP. MAX. UNIT

Contrast Ratio (Center of screen) Response Time at Ta Rising Falling

Luminance of white (Center of screen)

250 0.633 0.354 0.292 0.598 0.145 0.107 0.305 0.338 80 80 65 65 -

Red Color Chromaticity (CIE) Blue

Vert. Brightness Uniformity Flicker Cross talk

Panel Relative Humidity

Type Input Impedance Polarity Amplitude Display Color

positive and negative.

Horizontal Frequency Vertical Frequency

24KHz --80KHz 49Hz -------75Hz

85Hz refresh rate Support

Video input Connector

Monitor Block Diagram

MVPRL including ADC, Scaling LVDS And OSD function

Monitor board layout

Software flow chart

Software Flow Chart

Connecting the Display

Connecting the AC Power

Connecting the Audio Cable

Control panel (monitor front panel)

Main OSD Menu:

The description for control function :

The Color Temperature will be set to Cool.

Red Gain from Digital-register.

Green Gain Digital-register.

Blue Gain from Digital-register.

Set OSD display language to English.

The Language will be set to English.

Set OSD display language to Tranditional Chinese.

Set OSD display language to German.

Set OSD display language to French.

N/A N/A N/A

Set OSD display language to Japanese.

Adjust the horizontal position of the 0-100 OSD.

Adjust the verticalposition of the OSD.

Adjust the OSD timeout.

Hot-Key Menu:(For AR577 only)

The description for Hot-Key function :

The description for OSD Message :

Item of Factory menu

Plug and play