• Forged alloy steel, Quenched & Tempered, with alloy pins.

SHACKLES

G-209A
Grade 8 • Meets performance requirements of Grade 8 shackles.
• Working Load Limit permanently shown on every shackle.
• Hot-dip galvanized.
• Size 3/8 inch is mechanically galvanized.
• Shackles can be furnished proof tested with certificates to designated standards,
such as ABS, DNV, Lloyds, or other certification. Charges for proof testing and
certification available when requested at the time of order.
• Approved for use at -40° C (-40° F) to 204° C (400° F).
• Meets or exceeds all requirements of ASME B30.26 including identification, ductility,
design factor, proof load and temperature requirements. Importantly, these shackles
meet other critical performance requirements including impact properties and
material traceability, not addressed by ASME B30.26.
• G-209A Screw pin anchor shackles meet the performance requirements of Federal
Specification RR-C-271H, Type IVA, Grade B, Class 2, except for those provisions
required of the contractor.

G-209A Alloy Screw Anchor Pin Shackles APPLICATION AND WARNING INFORMATION
SECTION 17

Working Dimensions Tolerance

Nominal Load Weight (in) (+ / - in)
Size Limit Each
(in) (t) Stock No. (lb) A B C D E F G H L M P C A
3/8 2 1017450 .31 .66 .44 1.44 .38 1.03 .91 1.78 2.49 .25 2.03 .38 .13 .06
7/16 2.67 1017472 .38 .75 .50 1.69 .44 1.16 1.06 2.03 2.91 .31 2.38 .44 .13 .06
1/2 3.33 1017494 .63 .81 .63 1.88 .50 1.31 1.19 2.31 3.28 .38 2.69 .50 .13 .06
5/8 5 1017516 1.38 1.06 .75 2.38 .63 1.69 1.50 2.94 4.19 .44 3.34 .69 .13 .06
3/4 7 1017538 2.35 1.25 .88 2.81 .75 2.00 1.81 3.50 4.97 .50 3.97 .81 .25 .06
7/8 9.5 1017560 3.61 1.44 1.00 3.31 .88 2.28 2.09 4.03 5.83 .50 4.50 .97 .25 .06
1 12.5 1017582 5.32 1.69 1.13 3.75 1.00 2.69 2.38 4.69 6.56 .56 5.07 1.06 .25 .06
1-1/8 15 1017604 7.25 1.81 1.25 4.25 1.16 2.91 2.69 5.16 7.47 .63 5.59 1.25 .25 .06
1-1/4 18 1017626 9.88 2.03 1.38 4.69 1.29 3.25 3.00 5.75 8.25 .69 6.16 1.38 .25 .06
1-3/8 21 1017648 13.25 2.25 1.50 5.25 1.42 3.63 3.31 6.38 9.16 .75 6.84 1.50 .25 .13

4.5:1 Design Factor. Maximum Proof Load is 2 times the Working Load Limit (metric tons) and 2.2 times the Working Load Limit (short tons).
For Working Load Limit reduction due to side loading applications, see Warnings & Applications.

G-2169 P J

• Quenched & Tempered for maximum strength.

G
K

• Forged alloy steel.

• Available in galvanized (G) and self colored (S) finish. CONVENTIONAL
SHACKLE
• Can be individually proof tested and magnetic particle inspected H
R

upon request. Crosby certification available at time of order.

• Meets or exceeds all requirements of ASME B30.26 including L

identification, ductility, design factor, proof load and temperature "WIDE BODY"
S-2169 C
D
C E SHACKLE
requirements. Importantly, these shackles meet other critical M
B

performance requirements including fatigue life, impact

properties and material traceability, not addressed by ASME
B30.26.
• Look for the Red Pin®... the mark of genuine Crosby quality.

APPLICATION AND WARNING INFORMATION

SECTION 17
G-2169 / S-2169 Alloy Screw Pin Wide Body Shackles
Dimensions
(in)
Working Load B D
Limit G-2169 S-2169 Weight Each +/- +/-
(t) Stock No. Stock No. (lb) .25 C .02 E G H J K L M P R
7 1021655 1021664 3.5 1.25 .69 .88 1.82 1.25 3.56 1.60 1.25 .50 3.97 4.10 5.87
12.5 1021673 1021682 8.8 1.69 .92 1.13 2.38 1.37 4.63 2.13 1.63 .56 5.13 5.51 7.63
18 1021691 1021699 13 2.03 1.16 1.38 2.69 1.50 5.81 2.50 2.00 .69 6.25 6.76 9.38

5:1 Design Factor. Proof Load is 2 times the Working Load Limit.

28 thecrosbygroup.com Copyright © 2023 The Crosby Group LLC All Rights Reserved