TECHNICAL DATASHEET

LR Position Switches
n Technopolymer housing, one conduit entry
n Protection degree IP67 according to EN 60529
n 17 contact blocks available
n 48 actuators available
n M12 assembled connector versions
n Silver contacts gold plated versions
n Other versions available (see LM, LX, LZ datasheets)

Approvals

General data
Ambient temperature: -25°C … +80°C
Max. actuation frequency: 3600 operating cycles1/hour
Mechanical endurance: 20 million operating cycles1
Mounting position: any
Safety parameters:
B10d: 40,000,00 for NC contacts
Mechanical interlock, not coded: type 1 according to EN ISO 14119
(1) One operation cycle means two movements, one to close and one to open contacts, as defined in EN 60947‑5‑1.

Cable cross section (flexible copper strands)

Contact blocks C20, C21, C22, C33, C34: min. 1 x 0.34 mm2 (1 x AWG 22)
max. 2 x 1.5 mm2 (2 x AWG 16)
Contact block C5, C6, C7, C9, C10, C11, C12, C13, C14, C15, C16, C18: min. 1 x 0.5 mm2 (1 x AWG 20)
max. 2 x 2.5 mm2 (2 x AWG 14)
Contact block C2: min. 1 x 0.5 mm2 (1 x AWG 20)
max. 2 x 1.5 mm2 (2 x AWG 16)

In conformity with standards: In conformity with the requirements of:

IEC 60947-5-1, EN 60947-5-1, EN 60947-1, EN 50047, IEC 60204-1, EN 60204-1, Low Voltage Directive 2006/95/EC, Machinery Directive 2006/42/EC and
EN ISO 14119, EN ISO 12100, IEC 60529, EN 60529, UL 508, CSA 22.2 No.14 . EMC Directive 2004/108/EC.
Approvals: Positive contact opening in conformity with standards:
IEC 60947‑5‑1, UL 508, CSA 22.2 No.14, GB14048.5‑2001. IEC 60947‑5‑1, EN 60947‑5‑1.

Installation for safety applications:

Use only switches marked with the symbol aside the product code. Always connect the safety circuit to the NC contacts (normally closed contacts: C11-C12,
C21-C22 or C31-C32) as stated in standard EN 60947‑5‑1, encl. K, par. 2. Actuate the switch at least up to the positive opening travel shown in the travel diagrams.
Operate the switch at least with the positive opening force, indicated between brackets below each article, aside the minimum force value.

Electrical data Utilization category

Thermal current (Ith): 10 A

Rated insulation voltage (Ui): 500 Vac 600 Vdc Alternating current: AC15 (50÷60 Hz)
400 Vac 500 Vdc (contact blocks 2, 11, 12, 20, Ue (V) 250 400 500
connector

21, 22, 33, 34) Ie (A) 6 4 1

without

Rated impulse withstand voltage (Uimp): 6 kV Direct current: DC13

4 kV (contact blocks 20, 21, 22, 33, 34)
Conditional short circuit current: 1000 A according to EN 60947‑5‑1 Ue (V) 24 125 250
Protection against short circuits: type aM fuse 10 A 500 V Ie (A) 6 1.1 0.4
Pollution degree: 3
Alternating current: AC15 (50÷60 Hz)
Thermal current (Ith): 4A Ue (V) 24 120 250
with connector
M12, 4 poles

Rated insulation voltage (Ui): 250 Vac 300 Vdc Ie (A) 4 4 4

Protection against short circuits: type gG fuse 4 A 500 V Direct current: DC13
Pollution degree: 3 Ue (V) 24 125 250
Ie (A) 4 1.1 0.4

Alternating current: AC15 (50÷60 Hz)

Thermal current (Ith): 2A Ue (V) 24
with connector
M12, 8 poles

Rated insulation voltage (Ui): 30 Vac 36 Vdc Ie (A) 2

Protection against short circuits: type gG fuse 2 A 500 V Direct current: DC13
Pollution degree: 3 Ue (V) 24
Ie (A) 2
www.imopc.com
TECHNICAL DATASHEET

Specifications
Rated insulation voltage (Ui): 500 Vac
400 Vac (for contact blocks C2, C11, C12, C20,
C21, C22, C33, C34)
Conventional free air thermal current (Ith): 10 A UL Approval
Protection against short circuits: type aM fuse 10 A 500 V
Utilization categories Q300 (69 VA, 125 … 250 Vdc)
Rated impulse withstand voltage (Uimp): 6 kV A600 (720 VA, 120 … 600 Vac)
4 kV (for contact blocks C20, C21, C22, C33, C34) Data of housing type 1, 4X “indoor use only”, 12, 13
Protection degree of the housing: IP67 For all contact blocks except C2 and C3 use 60 or 75°C copper (Cu) conductor, rigid or
MV terminals (screw terminals) flexible, wire size AWG 12/14. Terminal tightening torque of 7.1 lb in (0.8 Nm).
Pollution degree 3 For contact blocks C2 and C3 use 60 or 75 °C copper (Cu) conductor, rigid or flexible,
Utilization category: AC15 wire size AWG 14. Terminal tightening torque of 12 lb in (1.4 Nm).
Operating voltage (Ue): 400 Vac (50 Hz)
Operating current (Ie): 3 A In conformity with standard: UL 508, CSA 22.2 No.14
Forms of the contact element: Za, Zb, Za+Za, Y+Y, X+X, Y+Y+X, Y+Y+Y, Y+X+X
Positive opening of contacts on contact blocks C5, C6, C7, C9, C11, C13, C14, C16, C18,
C20, C21, C22, C33, C34
In conformity with standards: EN 60947‑1, EN 60947‑5‑1+ A1:2009, fundamental requirements Please contact our technical service for the list of approved products.
of the Low Voltage Directive 2006/95/EC.
Please contact our technical service for the list of approved products.

Connection diagram for M12 connectors

Contact block C2 Contact block C5 Contact block C6 Contact block C7 Contact block C9 Contact block C10 Contact block C11 Contact block C12 Contact block C13
1NO-1NC+1NO-1NC 1NO+1NC 1NO+1NC 1NO+1NC 2NC 2NO 2NC 2NO 2NC

1 7 1 1 1 1 1 1 1 1

2 6
2 4 2 4 2 4 2 4 2 4 2 4 2 4 2 4
3 5
4 5 5 5 5 5 5 5 5
8 3 3 3 3 3 3 3 3
M12 connector, 8 poles M12 connector, 5 poles M12 connector, 5 poles M12 connector, 5 poles M12 connector, 5 poles M12 connector, 5 poles M12 connector, 5 poles M12 connector, 5 poles M12 connector, 5 poles

Contacts Pin no. Contacts Pin no. Contacts Pin no. Contacts Pin no. Contacts Pin no. Contacts Pin no. Contacts Pin no. Contacts Pin no. Contacts Pin no.
NO 3-4 NC 1-2 NC 1-2 NC 1-2 NC 1-2 NO 1-2 NC 1-2 NO 1-2 NC (1°) 1-2
NC 5-6 NO 3-4 NO 3-4 NO 3-4 NC 3-4 NO 3-4 NC 3-4 NO 3-4 NC (2°) 3-4
NC 7-8 ground 5 ground 5 ground 5 ground 5 ground 5 ground 5 ground 5 ground 5
NO 1-2

Contact block C14 Contact block C15 Contact block C16 Contact block C18 Contact block C20 Contact block C21 Contact block C22 Contact block C33 Contact block C34
2NC 2NO 2NC 1NO+1NC 2NC+1NO 3NC 1NC+2NO 1NC+1NO 2NC

1 1 1 1 1 7 1 7 1 7 1 1

2 6 2 6 2 6
2 4 2 4 2 4 2 4 2 4 2 4
3 5 3 5 3 5
5 5 5 5 4 4 4 5 5
3 3 3 3 8 8 8 3 3
M12 connector, 5 poles M12 connector, 5 poles M12 connector, 5 poles M12 connector, 5 poles M12 connector, 8 poles M12 connector, 8 poles M12 connector, 8 poles M12 connector, 5 poles M12 connector, 5 poles

Contacts Pin no. Contacts Pin no. Contacts Pin no. Contacts Pin no. Contacts Pin no. Contacts Pin no. Contacts Pin no. Contacts Pin no. Contacts Pin no.
NC (1°) 1-2 NO (1°) 1-2 NC, lever at the right 1-2 NC 1-2 NC 3-4 NC 3-4 NC 3-4 NC 1-2 NC 1-2
NC (2°) 3-4 NO (2°) 3-4 NC, lever to the left 3-4 NO 3-4 NC 5-6 NC 5-6 NO 5-6 NO 3-4 NC 3-4
ground 5 ground 5 ground 5 ground 5 NO 7-8 NC 7-8 NO 7-8 ground 5 ground 5
ground 1 ground 1 ground 1

Contact block CE1

PNP

2 4

5
3
M12 connector, 5 poles

Contacts Pin no.

+ 1
- 3
NC 2
NO 4
ground 5

www.imopc.com
 TECHNICAL DATASHEET

Selection diagram

A01 AA1 A08 A14 A02 AA2 AA4 A05 AA5

external rubber external rubber external rubber external rubber external rubber
gasket gasket gasket gasket gasket

A20 A21 A25 A34 A50 A33 A69 A53

round rod,
square rod fiber glass rod porcelain roller
stainless steel

WITH
RESET
A01-R A02-R A05-R A07-R A15-R A30-R A31-R A51-R
ACTUATORS

CONTACT BLOCKS
C5 C6 C7 C9 C10 C11 C12 C13 C14
1NO+1NC, 1NO+1NC, 1NO+1NC, 2NC 2NO 2NC 2NO 2NC 2NC
snap action slow action slow action, slow action slow action snap action snap action slow action slow action,
overlapped shifted and shifted
spaced

C15 C16 C18 C20 C21 C22 C2 CE1

2NO 2NC 1NO+1NC, 1NO+2NC, 3NC 2NO+1NC, 2x(1NO-1NC) 1NO-1NC
slow action, slow action slow action, slow action slow action slow action snap action electronic
shifted independent closer PNP

CONDUIT ENTRY

Threaded conduit entry With cable gland With M12 plastic connector With M12 metal connector
20 M20x1.5 (standard) for cables X70 4 poles, bottom X40 8 poles, bottom
X23
16 M16x1.5 Ø 6…Ø 12 mm X45 8 poles, bottom X60 4 poles, bottom
for cables
PG 13.5 X27
Ø 3…Ø 7 mm
11 PG 11
IN 1/2 NPT

product options
accessory sold separately

www.imopc.com
 TECHNICAL DATASHEET

A07 AA7 A15 A15-R28 A16 A10 A17 A12 A13 A76
roller roller roller
external rubber roller roller rope switch for
Ø 12 mm, Ø 12 mm, Ø 12 mm,
gasket Ø 11 mm Ø 20 mm signalling
stainless steel stainless steel stainless steel

A30 A31 A51 A52 A54 A55 A56 A57 A38

adjustable adjustable
without actuator
lever safety lever

LOOSE
ACTUATORS

A52-R A54-R A56-R A57-R A38-R

without actuator

Options & Ordering Codes Attention! The feasibility of a code number does not mean the effective availability of a product. Please contact our sales office.

LR C5 A02 1 R SS 20 X70
Housing Preinstalled Cable Gland or Connectors
polymer, one conduit entry LR no cable gland or connector (standard)
X21 assembled cable gland
Contact Blocks X70 4 poles M12 assembled plastic connector
1NO+1NC, snap action C5
1NO+1NC, slow action C6 Threaded Conduit Entry
1NO+1NC, slow action, overlapped C7 PG 13.5 (standard)
............................... ... 11 PG 11
Other contact blocks available upon request
16 M16 x 1.5

Actuators 20 M20 x 1.5

short plunger A01 IN 1/2 NPT

roller lever A02

External Metallic Parts
offset roller lever A05
Other actuators available upon request zinc plated steel (standard)
SS stainless steel
Suffix
no suffix (standard)
Reset Hooking
with stainless steel roller: - Ø 12mm for actuators AA4, A15
- Ø 14mm for actuators A2, A02, A5, A05 1 without reset (standard)
- Ø 20mm for actuators A30, A31, A51, A52, A54, A55, A56, A57
R simultaneous reset
with Ø 35mm polymer roller 2
RI simultaneous reset with increased force
with Ø 50mm rubber roller 3
with Ø 50mm overhanging rubber roller 4
www.imopc.com
 TECHNICAL DATASHEET

With external rubber gasket With stainless steel roller on request

Contact type:

R = snap action With external rubber gasket

L = slow action With stainless steel roller on request
LO = slow action
overlapped 5.5 5.5

14
14
LS = slow action Ø 12
shifted Ø8 12.2
12.2
LV = slow action
Ø8

40.1
40.1
shifted and 4.2x7.2 4.2x7.2 4.2x7.2 4.2x7.2

3
3
21.4

21
3
3

spaced
LI = slow action 20 12.2 20 12.2

91.6
91.6
20 20 24.2
independent 24.2 22 24.2
22 22 24.2
72.9

72.5
LA = slow action 22

51.5
51.5
51.5

51.5
closer
= electronic 14.2 14.2 14.2
PNP
14.2
30.8 30.8 30.8 30.8 30.8 30.8 30.8 30.8
Contact blocks
C5 R LRC5A01 1NO+1NC LRC5AA1 1NO+1NC LRC5A02 1NO+1NC LRC5AA2 1NO+1NC

C6 L LRC6A01 1NO+1NC LRC6AA1 1NO+1NC LRC6A02 1NO+1NC LRC6AA2 1NO+1NC

C7 LO LRC7A01 1NO+1NC LRC7AA1 1NO+1NC LRC7A02 1NO+1NC LRC7AA2 1NO+1NC

C9 L LRC9A01 2NC LRC9AA1 2NC LRC9A02 2NC LRC9AA2 2NC

C10 L LRC10A01 2NO LRC10AA1 2NO LRC10A02 2NO LRC10AA2 2NO

C11 R LRC11A01 2NC LRC11AA1 2NC LRC11A02 2NC LRC11AA2 2NC

C12 R LRC12A01 2NO LRC12AA1 2NO LRC12A02 2NO LRC12AA2 2NO

C13 LV LRC13A01 2NC LRC13AA1 2NC LRC13A02 2NC LRC13AA2 2NC

C14 LS LRC14A01 2NC LRC14AA1 2NC LRC14A02 2NC LRC14AA2 2NC

C15 LS LRC15A01 2NO LRC15AA1 2NO LRC15A02 2NO LRC15AA2 2NO

C18 LA LRC18A01 1NO+1NC LRC18AA1 1NO+1NC LRC18A02 1NO+1NC LRC18AA2 1NO+1NC

C20 L LRC20A01 1NO+2NC LRC20AA1 1NO+2NC LRC20A02 1NO+2NC LRC20AA2 1NO+2NC

C21 L LRC21A01 3NC LRC21AA1 3NC LRC21A02 3NC LRC21AA2 3NC

C22 L LRC22A01 2NO+1NC LRC22AA1 2NO+1NC LRC22A02 2NO+1NC LRC22AA2 2NO+1NC

C2 R LRC2A01 2x(1NO-1NC) LRC2A02 2x(1NO-1NC) LRC2AA2 2x(1NO-1NC)

CE1 LRCE1A01 1NO-1NC LRCE1AA1 1NO-1NC LRCE1A02 1NO-1NC LRCE1AA2 1NO-1NC

Max. speed Type 4 Type 4 Type 3 Type 3
Min. force 8 N (25 N ) 6 N (25 N ) 6 N (25 N ) 4.3 N (25 N )
Travel diagrams Group 1 Group 1 Group 2 Group 2

With external rubber gasket With stainless steel roller on request With external rubber gasket
With Ø 12 mm stainless steel roller on request With stainless steel roller on request

32(29-35) 20(17-23) 5.4

5.5 5.5
14

14

3.6
11

22
52
40.5

40.5

4.2x7.2 4.2x7.2 4.2x7.2 4.2x7.2

3

3
31

3
3

103.5

20 12.4 12.2 20 12.4 12.2

92

92

20 12.2 12.2
82.5

22 24.2 22 24.2 22 20
24.2 24.2
22
51.5

51.5

51.5

51.5

14.2 14.2 14.2 14.2

30.8 30.8 30.8 30.8 30.8 30.8 30.8 30.8
Contact blocks
C5 R LRC5AA4 1NO+1NC LRC5A05 1NO+1NC LRC5AA5 1NO+1NC LRC5A07 1NO+1NC

C6 L LRC6AA4 1NO+1NC LRC6A05 1NO+1NC LRC6AA5 1NO+1NC LRC6A07 1NO+1NC

C7 LO LRC7AA4 1NO+1NC LRC7A05 1NO+1NC LRC7AA5 1NO+1NC LRC7A07 1NO+1NC

C9 L LRC9AA4 2NC LRC9A05 2NC LRC9AA5 2NC LRC9A07 2NC

C10 L LRC10AA4 2NO LRC10A05 2NO LRC10AA5 2NO LRC10A07 2NO

C11 R LRC11AA4 2NC LRC11A05 2NC LRC11AA5 2NC LRC11A07 2NC

C12 R LRC12AA4 2NO LRC12A05 2NO LRC12AA5 2NO LRC12A07 2NO

C13 LV LRC13AA4 2NC LRC13A05 2NC LRC13AA5 2NC LRC13A07 2NC

C14 LS LRC14AA4 2NC LRC14A05 2NC LRC14AA5 2NC LRC14A07 2NC

C15 LS LRC15AA4 2NO LRC15A05 2NO LRC15AA5 2NO LRC15A07 2NO

C18 LA LRC18AA4 1NO+1NC LRC18A05 1NO+1NC LRC18AA5 1NO+1NC LRC18A07 1NO+1NC

C20 L LRC20AA4 1NO+2NC LRC20A05 1NO+2NC LRC20AA5 1NO+2NC LRC20A07 1NO+2NC

C21 L LRC21AA4 3NC LRC21A05 3NC LRC21AA5 3NC LRC21A07 3NC

C22 L LRC22AA4 2NO+1NC LRC22A05 2NO+1NC LRC22AA5 2NO+1NC LRC22A07 2NO+1NC

C2 R LRC2A05 2x(1NO-1NC) LRC2AA5 2x(1NO-1NC) LRC2A07 2x(1NO-1NC)

CE1 LRCE1AA4 1NO-1NC LRCE1A05 1NO-1NC LRCE1AA5 1NO-1NC LRCE1A07 1NO-1NC

Max. speed Type 5 Type 3 Type 3 Type 3
Min. force 6 N (25 N ) 6 N (25 N ) 4.3 N (25 N ) 4 N (25 N )
Travel diagrams Group 1 Group 2 Group 2 Group 3
All measures in the drawings are in mm

www.imopc.com
TECHNICAL DATASHEET

With external rubber gasket With external rubber gasket

Contact type:

R = snap action Fixed only by threaded head in vertical

L = slow action position
LO = slow action 32(29-35) 20(17-23) 5.4

8.4
overlapped Ø8
LS = slow action

5.8
Ø 7.4 24

4
shifted 12.2 M 18x1
14

25.2
LV = slow action Ø 10
M12x1

14.2
22
shifted and

30.1
52

4.2x7.2 4.2x7.2

2.5
spaced 4.2x7.2

3
3

100.1
3

LI = slow action
12.2 20 12.2
20
103.5

87.5
independent 24.2

81.6
12.2 22 22 24.2
LA = slow action 20

51.5
24.2

51.5
closer 22
51.5

= electronic
14.2 14.2 14.2
PNP 14.2
30.8 30.8 30.8 30.8 30.8 30.8
30.8 30.8
Contact blocks
C5 R LRC5AA7 1NO+1NC LRC5A08 1NO+1NC LRC5A10 1NO+1NC LRC5A12 1NO+1NC

C6 L LRC6AA7 1NO+1NC LRC6A08 1NO+1NC LRC6A10 1NO+1NC LRC6A12 1NO+1NC

C7 LO LRC7AA7 1NO+1NC LRC7A08 1NO+1NC LRC7A10 1NO+1NC LRC7A12 1NO+1NC

C9 L LRC9AA7 2NC LRC9A08 2NC LRC9A10 2NC LRC9A12 2NC

C10 L LRC10AA7 2NO LRC10A08 2NO LRC10A10 2NO LRC10A12 2NO

C11 R LRC11AA7 2NC LRC11A08 2NC LRC11A10 2NC LRC11A12 2NC

C12 R LRC12AA7 2NO LRC12A08 2NO LRC12A10 2NO LRC12A12 2NO

C13 LV LRC13AA7 2NC LRC13A08 2NC LRC13A10 2NC LRC13A12 2NC

C14 LS LRC14AA7 2NC LRC14A08 2NC LRC14A10 2NC LRC14A12 2NC

C15 LS LRC15AA7 2NO LRC15A08 2NO LRC15A10 2NO LRC15A12 2NO

C18 LA LRC18AA7 1NO+1NC LRC18A08 1NO+1NC LRC18A10 1NO+1NC LRC18A12 1NO+1NC

C20 L LRC20AA7 1NO+2NC LRC20A08 1NO+2NC LRC20A10 1NO+2NC LRC20A12 1NO+2NC

C21 L LRC21AA7 3NC LRC21A08 3NC LRC21A10 3NC LRC21A12 3NC

C22 L LRC22AA7 2NO+1NC LRC22A08 2NO+1NC LRC22A10 2NO+1NC LRC22A12 2NO+1NC

C2 R LRC2AA7 2x(1NO-1NC) LRC2A08 2x(1NO-1NC) LRC2A10 2x(1NO-1NC) LRC2A12 2x(1NO-1NC)

CE1 LRCE1AA7 1NO-1NC LRCE1A08 1NO-1NC LRCE1A10 1NO-1NC LRCE1A12 1NO-1NC

Max. speed Type 3 Type 4 Type 4 Type 4
Min. force 3 N (25 N ) 8 N (25 N ) 8 N (25 N ) 8 N (25 N )
Travel diagrams Group 3 Group 1 Group 1 Group 1

Roller, Ø 11 mm, technopolymer Roller, Ø 12 mm, stainless steel

12
8.4

3.8

24 3.6 3.8
4

13

M 18x1 11 12
25.2

4.2x7.2
31.5

4.2x7.2 4.2x7.2
27.9

4.2x7.2
3

31

3
3
3

12.2
100.1

20 12.2 20
79.4

24.2 20 12.2 20 12.2

82.5

22 24.2 22 22 24.2 22 24.2

83
51.5
51.5

51.5
51.5

14.2 14.2 14.2 14.2

30.8 30.8 30.8 30.8 30.8 30.8 30.8 30.8
Contact blocks
C5 R LRC5A13 1NO+1NC LRC5A14 1NO+1NC LRC5A15 1NO+1NC LRC5A15-20 1NO+1NC

C6 L LRC6A13 1NO+1NC LRC6A14 1NO+1NC LRC6A15 1NO+1NC LRC6A15-20 1NO+1NC

C7 LO LRC7A13 1NO+1NC LRC7A14 1NO+1NC LRC7A15 1NO+1NC LRC7A15-20 1NO+1NC

C9 L LRC9A13 2NC LRC9A14 2NC LRC9A15 2NC LRC9A15-20 2NC

C10 L LRC10A13 2NO LRC10A14 2NO LRC10A15 2NO LRC10A15-20 2NO

C11 R LRC11A13 2NC LRC11A14 2NC LRC11A15 2NC LRC11A15-20 2NC

C12 R LRC12A13 2NO LRC12A14 2NO LRC12A15 2NO LRC12A15-20 2NO

C13 LV LRC13A13 2NC LRC13A14 2NC LRC13A15 2NC LRC13A15-20 2NC

C14 LS LRC14A13 2NC LRC14A14 2NC LRC14A15 2NC LRC14A15-20 2NC

C15 LS LRC15A13 2NO LRC15A14 2NO LRC15A15 2NO LRC15A15-20 2NO

C18 LA LRC18A13 1NO+1NC LRC18A14 1NO+1NC LRC18A15 1NO+1NC LRC18A15-20 1NO+1NC

C20 L LRC20A13 1NO+2NC LRC20A14 1NO+2NC LRC20A15 1NO+2NC LRC20A15-20 1NO+2NC

C21 L LRC21A13 3NC LRC21A14 3NC LRC21A15 3NC LRC21A15-20 3NC

C22 L LRC22A13 2NO+1NC LRC22A14 2NO+1NC LRC22A15 2NO+1NC LRC22A15-20 2NO+1NC

C2 R LRC2A13 2x(1NO-1NC) LRC2A14 2x(1NO-1NC) LRC2A15 2x(1NO-1NC) LRC2A15-20 2x(1NO-1NC)

CE1 LRCE1A13 1NO-1NC LRCE1A14 1NO-1NC LRCE1A15 1NO-1NC LRCE1A15-20 1NO-1NC

Max. speed Type 2 Type 4 Type 2 Type 2
Min. force 8 N (25 N ) 8 N (25 N ) 8 N (25 N ) 8 N (25 N )
Travel diagrams Group 1 Group 1 Group 1 Group 1
All measures in the drawings are in mm

www.imopc.com
 TECHNICAL DATASHEET

Fixed only by threaded head in vertical With external rubber gasket

position
Contact type:

R = snap action Ø 1.2

L = slow action

55
LO = slow action

141
124
overlapped 3.8
LS = slow action 3.6 Ø7
12

20
shifted

192.5
175.5
20

3
LV = slow action
17
shifted and
40.5

M12x1

13
spaced 4.2x7.2 4.2x7.2
3

3
24
4.2x7.2

3
LI = slow action

24
20 12.2 20 12.2

101
independent
92

12.2
= slow action 22 24.2 24.2 20 12.2
LA 22
24.2
closer 22

51.5
51.5

= electronic

51.5
PNP 14.2 14.2
14.2
30.8 30.8 14.2
30.8 30.8 30.8 30.8
Contact blocks 30.8 30.8

C5 R LRC5A16-20 1NO+1NC LRC5A17-20 1NO+1NC LRC5A20-20 1NO+1NC LRC5A21-20 1NO+1NC

C6 L LRC6A16-20 1NO+1NC LRC6A17-20 1NO+1NC

C7 LO LRC7A16-20 1NO+1NC LRC7A17-20 1NO+1NC

C9 L LRC9A16-20 2NC LRC9A17-20 2NC

C10 L LRC10A16-20 2NO LRC10A17-20 2NO LRC10A20-20 2NO LRC10A21-20 2NO

C11 R LRC11A16-20 2NC LRC11A17-20 2NC

C12 R LRC12A16-20 2NO LRC12A17-20 2NO LRC12A20-20 2NO LRC12A21-20 2NO

C13 LV LRC13A16-20 2NC LRC13A17-20 2NC

C14 LS LRC14A16-20 2NC LRC14A17-20 2NC

C15 LS LRC15A16-20 2NO LRC15A17-20 2NO

C18 LA LRC18A16-20 1NO+1NC LRC18A17-20 1NO+1NC LRC18A20-20 1NO+1NC LRC18A21-20 1NO+1NC

C20 L LRC20A16-20 1NO+2NC LRC20A17-20 1NO+2NC LRC20A20-20 1NO+2NC LRC20A21-20 1NO+2NC

C21 L LRC21A16-20 3NC LRC21A17-20 3NC LRC21A20-20 3NC LRC21A21-20 3NC

C22 L LRC22A16-20 2NO+1NC LRC22A17-20 2NO+1NC LRC22A20-20 2NO+1NC LRC22A21-20 2NO+1NC

C2 R LRC2A16-20 2x(1NO-1NC) LRC2A17-20 2x(1NO-1NC) LRC2A20-20 2x(1NO-1NC) LRC2A21-20 2x(1NO-1NC)

CE1 LRCE1A16-20 1NO-1NC LRCE1A17-20 1NO-1NC LRCE1A20-20 1NO-1NC LRCE1A21-20 1NO-1NC

Max. speed Type 2 Type 2 1 m/s 1 m/s
Min. force 8 N (25 N ) 8 N (25 N ) 0.07 Nm 0.07 Nm
Travel diagrams Group 1 Group 1 Group 4 Group 4

With external rubber gasket With Ø 20 mm stainless steel roller on request Square rod, 3x3 mm

3x3x125
Ø 7.5 41.5 39.4
16.5 5.4
127

18 18 4.5 35
38 - 135

31.1
178.5

5.4
54

54

89.5 - 186.5

4.2x7.2
28

28
28
3

19
24

3
3

19
105.5

19
3

4.2x7.2
105.5

12.2 4.2x7.2 24.2 20 24.2

20 20
22
4.2x7.2 24.2
22 24.2 22
51.5

51.5
51.5
51.5

20
14.2 14.2 22 14.2
14.2
30.8 30.8 30.8 30.8 30.8 30.8
30.8 30.8
Contact blocks
C5 R LRC5A25-20 1NO+1NC LRC5A30-20 1NO+1NC LRC5A31-20 1NO+1NC LRC5A33-20 1NO+1NC
C6 L LRC6A30-20 1NO+1NC LRC6A31-20 1NO+1NC LRC6A33-20 1NO+1NC
C7 LO LRC7A30-20 1NO+1NC LRC7A31-20 1NO+1NC LRC7A33-20 1NO+1NC
C9 L LRC9A30-20 2NC LRC9A31-20 2NC LRC9A33-20 2NC
C10 L LRC10A25-20 2NO LRC10A30-20 2NO LRC10A31-20 2NO LRC10A33-20 2NO
C11 R LRC11A30-20 2NC LRC11A31-20 2NC LRC11A33-20 2NC
C12 R LRC12A25-20 2NO LRC12A30-20 2NO LRC12A31-20 2NO LRC12A33-20 2NO
C13 LV LRC13A30-20 2NC LRC13A31-20 2NC LRC13A33-20 2NC
C14 LS LRC14A30-20 2NC LRC14A31-20 2NC LRC14A33-20 2NC
C15 LS LRC15A30-20 2NO LRC15A31-20 2NO LRC15A33-20 2NO
C16 LI LRC16A30-20 2NC LRC16A31-20 2NC LRC16A33-20 2NC
C18 LA LRC18A25-20 1NO+1NC LRC18A30-20 1NO+1NC LRC18A31-20 1NO+1NC LRC18A33-20 1NO+1NC
C20 L LRC20A25-20 1NO+2NC LRC20A30-20 1NO+2NC LRC20A31-20 1NO+2NC LRC20A33-20 1NO+2NC
C21 L LRC21A25-20 3NC LRC21A30-20 3NC LRC21A31-20 3NC LRC21A33-20 3NC
C22 L LRC22A25-20 2NO+1NC LRC22A30-20 2NO+1NC LRC22A31-20 2NO+1NC LRC22A33-20 2NO+1NC
C2 R LRC2A25-20 2x(1NO-1NC) LRC2A30-20 2x(1NO-1NC) LRC2A31-20 2x(1NO-1NC) LRC2A33-20 2x(1NO-1NC)
CE1 LRCE1A25-20 1NO-1NC LRCE1A30-20 1NO-1NC LRCE1A31-20 1NO-1NC LRCE1A33-20 1NO-1NC
Max. speed 1 m/s Type 1 Type 1 1.5 m/s
Min. force 0.12 Nm 0.06 Nm (0.25 Nm ) 0.06 Nm (0.25 Nm ) 0.06 Nm
Travel diagrams Group 4 Group 5 Group 5 Group 5
All measures in the drawings are in mm

www.imopc.com
TECHNICAL DATASHEET

Round rod, Ø 3 mm, stainless steel

Contact type:

R = snap action
41.5
L = slow action Ø3x125 54 40

55

20
LO = slow action 7
27.5

20
overlapped 125
LS = slow action 4.5 35

38 - 135
shifted Ø 7.3 29 7

67.6
14.6
176.5

LV = slow action

59
89.5 - 186.5
shifted and

28
spaced

28
28
3

28

3
3
3
19

4.2x7.2

119.1
19

19

19
4.2x7.2
4.2x7.2
LI = slow action

110.5

4.2x7.2
independent
20 24.2 24.2 20 24.2 20 24.2
LA = slow action
22 22 22
closer

51.5

51.5
51.5

51.5
= electronic 20
PNP 14.2 22 14.2 14.2 14.2
30.8 30.8 30.8 30.8 30.8 30.8 30.8 30.8
Contact blocks
C5 R LRC5A34-20 1NO+1NC LRC5A50-20 1NO+1NC LRC5A51-20 1NO+1NC LRC5A52-20 1NO+1NC
C6 L LRC6A34-20 1NO+1NC LRC6A50-20 1NO+1NC LRC6A51-20 1NO+1NC LRC6A52-20 1NO+1NC
C7 LO LRC7A34-20 1NO+1NC LRC7A50-20 1NO+1NC LRC7A51-20 1NO+1NC LRC7A52-20 1NO+1NC
C9 L LRC9A34-20 2NC LRC9A50-20 2NC LRC9A51-20 2NC LRC9A52-20 2NC
C10 L LRC10A34-20 2NO LRC10A50-20 2NO LRC10A51-20 2NO LRC10A52-20 2NO
C11 R LRC11A34-20 2NC LRC11A50-20 2NC LRC11A51-20 2NC LRC11A52-20 2NC
C12 R LRC12A34-20 2NO LRC12A50-20 2NO LRC12A51-20 2NO LRC12A52-20 2NO
C13 LV LRC13A34-20 2NC LRC13A50-20 2NC LRC13A51-20 2NC LRC13A52-20 2NC
C14 LS LRC14A34-20 2NC LRC14A50-20 2NC LRC14A51-20 2NC LRC14A52-20 2NC
C15 LS LRC15A34-20 2NO LRC15A50-20 2NO LRC15A51-20 2NO LRC15A52-20 2NO
C16 LI LRC16A34-20 2NC LRC16A50-20 2NC LRC16A51-20 2NC LRC16A52-20 2NC
C18 LA LRC18A34-20 1NO+1NC LRC18A50-20 1NO+1NC LRC18A51-20 1NO+1NC LRC18A52-20 1NO+1NC
C20 L LRC20A34-20 1NO+2NC LRC20A50-20 1NO+2NC LRC20A51-20 1NO+2NC LRC20A52-20 1NO+2NC
C21 L LRC21A34-20 3NC LRC21A50-20 3NC LRC21A51-20 3NC LRC21A52-20 3NC
C22 L LRC22A34-20 2NO+1NC LRC22A50-20 2NO+1NC LRC22A51-20 2NO+1NC LRC22A52-20 2NO+1NC
C2 R LRC2A34-20 2x(1NO-1NC) LRC2A50-20 2x(1NO-1NC) LRC2A51-20 2x(1NO-1NC) LRC2A52-20 2x(1NO-1NC)
CE1 LRCE1A34-20 1NO-1NC LRCE1A50-20 1NO-1NC LRCE1A51-20 1NO-1NC LRCE1A52-20 1NO-1NC
Max. speed 1.5 m/s 1.5 m/s Type 1 Type 1
Min. force 0.06 Nm 0.06 Nm 0.06 Nm (0.25 Nm ) 0.06 Nm (0.25 Nm )
Travel diagrams Group 5 Group 5 Group 5 Group 5

Porcelain roller

40 40
Ø9 41.5
44 20 20
56.5

20
27.5
99.3

29 7 29 7
53 - 112
53 - 112

25 7
59
150.8

104.5 - 163.5
104.5 - 163.5

28
3
28
3
28
3
28
3

19
19
19

4.2x7.2
19

4.2x7.2
4.2x7.2
110.5
4.2x7.2

20 24.2 20 24.2 24.2 24.2

22 22
20 20
51.5
51.5
51.5
51.5

22 22
14.2 14.2 14.2 14.2
30.8 30.8 30.8 30.8 30.8 30.8 30.8 30.8
Contact blocks
C5 R LRC5A53-20 1NO+1NC LRC5A54-20 1NO+1NC LRC5A55-20 (1) 1NO+1NC LRC5A56-20 1NO+1NC
C6 L LRC6A53-20 1NO+1NC LRC6A54-20 1NO+1NC LRC6A55-20 (1) 1NO+1NC LRC6A56-20 1NO+1NC
C7 LO LRC7A53-20 1NO+1NC LRC7A54-20 1NO+1NC LRC7A55-20 (1) 1NO+1NC LRC7A56-20 1NO+1NC
C9 L LRC9A53-20 2NC LRC9A54-20 2NC LRC9A55-20 (1) 2NC LRC9A56-20 2NC
C10 L LRC10A53-20 2NO LRC10A54-20 2NO LRC10A55-20 2NO LRC10A56-20 2NO
C11 R LRC11A54-20 2NC LRC11A55-20 (1) 2NC LRC11A56-20 2NC
C12 R LRC12A53-20 2NO LRC12A54-20 2NO LRC12A55-20 2NO LRC12A56-20 2NO
C13 LV LRC13A53-20 2NC LRC13A54-20 2NC LRC13A55-20 (1) 2NC LRC13A56-20 2NC
C14 LS LRC14A53-20 2NC LRC14A54-20 2NC LRC14A55-20 (1) 2NC LRC14A56-20 2NC
C15 LS LRC15A53-20 2NO LRC15A54-20 2NO LRC15A55-20 2NO LRC15A56-20 2NO
C16 LI LRC16A54-20 2NC LRC16A55-20 (1) 2NC LRC16A56-20 2NC
C18 LA LRC18A53-20 1NO+1NC LRC18A54-20 1NO+1NC LRC18A55-20 (1) 1NO+1NC LRC18A56-20 1NO+1NC
C20 L LRC20A53-20 1NO+2NC LRC20A54-20 1NO+2NC LRC20A55-20 (1) 1NO+2NC LRC20A56-20 1NO+2NC
C21 L LRC21A53-20 3NC LRC21A54-20 3NC LRC21A55-20 (1) 3NC LRC21A56-20 3NC
C22 L LRC22A53-20 2NO+1NC LRC22A54-20 2NO+1NC LRC22A55-20 (1) 2NO+1NC LRC22A56-20 2NO+1NC
C2 R LRC2A53-20 2x(1NO-1NC) LRC2A54-20 2x(1NO-1NC) LRC2A55-20 2x(1NO-1NC) LRC2A56-20 2x(1NO-1NC)
CE1 LRCE1A53-20 1NO-1NC LRCE1A54-20 1NO-1NC LRCE1A55-20 1NO-1NC LRCE1A56-20 1NO-1NC
Max. speed 0.5 m/s Type 1 Type 1 Type 1
Min. force 0.03 Nm (0.25 Nm ) 0.06 Nm (0.25 Nm ) 0.06 Nm (0.25 Nm ) 0.06 Nm (0.25 Nm )
Travel diagrams Group 6 Group 5 Group 5 Group 5
(1) All measures in the drawings are in mm
Positive opening only with actuator set to max.

www.imopc.com
 TECHNICAL DATASHEET

Fiber glass rod Rope switch for signalling

Contact type:

R = snap action
L = slow action Ø6x200
36.5
LO = slow action 50
overlapped 20 12.2

38 - 208
LS = slow action

15.3
shifted
= slow action 19 7 10
LV

89.5 - 259.5
62

shifted and

38.8
spaced 4.2x7.2

3
28
3
28
3

19
19

LI = slow action

108.6
113.5

4.2x7.2

independent 20
= slow action 20 24.2 24.2 24.2
LA 22

4.2X7.2
closer 22

51.5
51.5
51.5

= electronic 20
PNP 14.2 22 14.2 14.2
30.8 30.8 30.8 30.8 30.8 30.8
Contact blocks
C5 R LRC5A57-20 1NO+1NC LRC5A69-20 1NO+1NC LRC5A76-20 1NO+1NC
C6 L LRC6A57-20 1NO+1NC LRC6A69-20 1NO+1NC LRC6A76-20 1NO+1NC
C7 LO LRC7A57-20 1NO+1NC LRC7A69-20 1NO+1NC LRC7A76-20 1NO+1NC
C9 L LRC9A57-20 2NC LRC9A69-20 2NC LRC9A76-20 2NO
C10 L LRC10A57-20 2NO LRC10A69-20 2NO LRC10A76-20 2NC
C11 R LRC11A57-20 2NC LRC11A69-20 2NC LRC11A76-20 2NO
C12 R LRC12A57-20 2NO LRC12A69-20 2NO LRC12A76-20 2NC
C13 LV LRC13A57-20 2NC LRC13A69-20 2NC LRC13A76-20 2NO
C14 LS LRC14A57-20 2NC LRC14A69-20 2NC LRC14A76-20 2NO
C15 LS LRC15A57-20 2NO LRC15A69-20 2NO LRC15A76-20 2NC
C16 LI LRC16A57-20 2NC LRC16A69-20 2NC
C18 LA LRC18A57-20 1NO+1NC LRC18A69-20 1NO+1NC LRC18A76-20 1NO+1NC
C20 L LRC20A57-20 1NO+2NC LRC20A69-20 1NO+2NC LRC20A76-20 2NO+1NC
C21 L LRC21A57-20 3NC LRC21A69-20 3NC LRC21A76-20 3NO
C22 L LRC22A57-20 2NO+1NC LRC22A69-20 2NO+1NC LRC22A76-20 1NO+2NC
C2 R LRC2A57-20 2x(1NO-1NC) LRC2A69-20 2x(1NO-1NC) LRC2A76-20 2x(1NO-1NC)
CE1 LRCE1A57-20 1NO-1NC LRCE1A69-20 1NO-1NC
Max. speed Type 1 1.5 m/s 0.5 m/s
Min. force 0.06 Nm (0.25 Nm ) 0.06 Nm initial 20 N - final 40 N
Travel diagrams Group 5 Group 5 Group 7

Position switches LR series with reset

IMO Precision Controls has developed a range of position switches that incorporate a Reset device. This is denoted by the addition of the suffix R to the part numbers.
The Reset device is a block inserted between the switch body and the head, and it can be rotated and positioned in four locations independent to the head. Some of the
features of the Reset device are as follows:
• Easy integration in to almost all standard heads
• No need to use snap action contact blocks as the tripping movement is defined by the Reset device
• Rotation for ease of installation
• Two driving forces are available - standard and increased for use in applications where vibration is present
• Mechanical endurance - up to 1 million operating cycles.

With stainless steel roller on request With stainless steel roller on request

32(29-35) 20(17-23) 5.4

5.5 5.5
14

14
22

Ø8
65
53.1

53.5
34.4

116.5

3
3

15
3

15
15

15
104.6

105

20
12.2 20 4.2x7.2 12.2 12.4 12.2 20
12.2
85.9

4.2x7.2 24.2 20 4.2x7.2

22 24.2 22 24.2 22 24.2
45.4 22 4.2x7.2
51.5

51.5

45.4
51.5
51.5

45.4 45.4
14.2 14.2 14.2 14.2
30.8 30.8 30.8 30.8 30.8 30.8 30.8 30.8
Contact blocks
C6 L LRC6A01-R20 1NO+1NC LRC6A02-R20 1NO+1NC LRC6A05-R20 1NO+1NC LRC6A07-R20 1NO+1NC

C9 L LRC9A01-R20 2NC LRC9A02-R20 2NC LRC9A05-R20 2NC LRC9A07-R20 2NC

C10 L LRC10A01-R20 2NO LRC10A02-R20 2NO LRC10A05-R20 2NO LRC10A07-R20 2NO

C20 L LRC20A01-R20 1NO+2NC LRC20A02-R20 1NO+2NC LRC20A05-R20 1NO+2NC LRC20A07-R20 1NO+2NC

C21 L LRC21A01-R20 3NC LRC21A02-R20 3NC LRC21A05-R20 3NC LRC21A07-R20 3NC

C22 L LRC22A01-R20 2NO+1NC LRC22A02-R20 2NO+1NC LRC22A05-R20 2NO+1NC LRC22A07-R20 2NO+1NC

C2 R LRC2A01-R20 2NO+2NC LRC2A02-R20 2NO+2NC LRC2A05-R20 2NO+2NC LRC2A07-R20 2NO+2NC

Max. speed Type 4 Type 3 Type 3 Type 3
Min. force 4.5 N (25 N ) 4 N (25 N ) 4 N (25 N ) 2.5 N (25 N )
Travel diagrams Group 1 Group 2 Group 2 Group 3
All measures in the drawings are in mm

www.imopc.com
TECHNICAL DATASHEET
Contact type: With Ø 12 mm stainless steel roller on request With Ø 20 mm stainless steel roller on request

R = snap action
L = slow action
33.2 54.9
33.2 42.1 33.2 39.4 7
16.1 20
18 18
3.6 15.6
11 5.4 31.1 5.4

72
67
67
44

41
41
41

32
123.5
32
32

15
118.5
3

118.5

15
15

15

3
3
12.2
95.5

12.2 20 12.2 12.2 20

20 4.2x7.2 20 24.2

3
24.2 22 4.2x7.2 24.2 4.2x7.2 24.2 22 4.2x7.2
22 22

51.5
39.5
51.5

51.5
45.4

51.5
14.2 14.2 14.2 14.2

30.8 30.8 30.8 30.8 30.8 30.8 30.8 30.8

Contact blocks
C6 L FR 615-W3M2 1NO+1NC FR 630-W3M2 1NO+1NC FR 631-W3M2 1NO+1NC FR 651-W3M2 1NO+1NC
C9 L LRC9A15-R20 2NC LRC9A30-R20 2NC LRC9A31-R20 2NC LRC9A51-R20 2NC
C10 L FR 1015-W3M2 2NO FR 1030-W3M2 2NO FR 1031-W3M2 2NO FR 1051-W3M2 2NO
C20 L LRC20A15-R20 1NO+2NC LRC20A30-R20 1NO+2NC LRC20A31-R20 1NO+2NC LRC20A51-R20 1NO+2NC
C21 L FR 2115-W3M2 3NC FR 2130-W3M2 3NC FR 2131-W3M2 3NC FR 2151-W3M2 3NC
C22 L LRC22A15-R20 2NO+1NC LRC22A30-R20 2NO+1NC LRC22A31-R20 2NO+1NC LRC22A51-R20 2NO+1NC
C2 R FR 215-W3M2 2NO+2NC FR 230-W3M2 2NO+2NC FR 231-W3M2 2NO+2NC FR 251-W3M2 2NO+2NC
Max. speed Type 2 Type 1 Type 1 Type 1
Min. force 4.5 N (25 N ) 0.07 Nm (0.25 Nm ) 0.07 Nm (0.25 Nm ) 0.07 Nm (0.25 Nm )
Travel diagrams Group 1 Group 4 Group 4 Group 4

33.2 40.4
20
33.2 40.4
7 33.2 50.4
20 33.2 44.4 7
7 20
20 30.1 7

30.1
66 - 125

20.1
26
80.6

75
117.5 - 176.5
72

41

41
41

32
132.1

41

126.5
32

32
32
123.5

15

15
15

15

3
12.2
3

12.2 12.2 20 12.2

20 20 4.2x7.2 4.2x7.2 20 24.2
4.2x7.2 24.2 24.2 22 24.2 4.2x7.2
22 22
51.5

22

51.5
51.5

51.5

14.2 14.2 14.2 14.2

30.8 30.8 30.8 30.8 30.8 30.8 30.8 30.8
Contact blocks
C6 L FR 652-W3M2 1NO+1NC FR 654-W3M2 1NO+1NC FR 656-W3M2 1NO+1NC FR 657-W3M2 1NO+1NC
C9 L LRC9A52-R20 2NC LRC9A54-R20 2NC LRC9A56-R20 2NC LRC9A57-R20 2NC
C10 L FR 1052-W3M2 2NO FR 1054-W3M2 2NO FR 1056-W3M2 2NO FR 1057-W3M2 2NO
C20 L LRC20A52-R20 1NO+2NC LRC20A54-R20 1NO+2NC LRC20A56-R20 1NO+2NC LRC20A57-R20 1NO+2NC
C21 L FR 2152-W3M2 3NC FR 2154-W3M2 3NC FR 2156-W3M2 3NC FR 2157-W3M2 3NC
C22 L LRC22A52-R20 2NO+1NC LRC22A54-R20 2NO+1NC LRC22A56-R20 2NO+1NC LRC22A57-R20 2NO+1NC
C2 R FR 252-W3M2 2NO+2NC FR 254-W3M2 2NO+2NC FR 256-W3M2 2NO+2NC FR 257-W3M2 2NO+2NC
Max. speed Type 1 Type 1 Type 1 Type 1
Min. force 0.07 Nm (0.25 Nm ) 0.07 Nm (0.25 Nm ) 0.07 Nm (0.25 Nm ) 0.07 Nm (0.25 Nm )
Travel diagrams Group 4 Group 4 Group 4 Group 4
All measures in the drawings are in mm

Increased actuating force

The switch can be delivered with increased
actuating force (option RI). Ideal for
applications with vibrations.
Actuators Min. force
01, 14, 15, 16 7N
02, 05 6N
07 3.5 N
30 ... 57 0.08 Nm

www.imopc.com
 TECHNICAL DATASHEET

Position switches with revolving lever without actuator

Contact type:
With manual reset knob
R = snap action
L = slow action
LO = slow action All measures in the drawings are in mm
overlapped
30.9
LS = slow action 30.9 33.2 IMPORTANT

M4
9

shifted

M4
LV = slow action For safety applications: join only switches and actuators marked with
shifted and symbol aside the product code.

41
28
3
19

spaced

15
4.2x7.2

3
LI = slow action 20 20 12.2
24.2 4.2x7.2
independent 22 22 24.2
= slow action
51.5

LA

51.5
closer
= electronic
14.2 14.2
PNP 30.8 30.8 30.8 30.8
Contact blocks
C5 R LRC5A38-20 1NO+1NC
C6 L LRC6A38-20 1NO+1NC LRC6A38-R20 1NO+1NC
C7 LO LRC7A38-20 1NO+1NC
C9 L LRC9A38-20 2NC LRC9A38-R20 2NC
C10 L LRC10A38-20 2NO LRC10A38-R20 2NO
C11 R LRC11A38-20 2NC
C12 R LRC12A38-20 2NO
C13 LV LRC13A38-20 2NC
C14 LS LRC14A38-20 2NC
C15 LS LRC15A38-20 2NO
C16 LI LRC16A38-20 2NC
C18 LA LRC18A38-20 1NO+1NC
C20 L LRC20A38-20 1NO+2NC LRC20A38-R20 1NO+2NC
C21 L LRC21A38-20 3NC LRC21A38-R20 3NC
C22 L LRC22A38-20 2NO+1NC LRC22A38-R20 2NO+1NC
C2 R LRC2A38-20 2x(1NO-1NC) LRC2A38-R20 2NO+2NC
CE1 LRCE1A38-20 1NO-1NC
Min. force 0.06 Nm (0.25 Nm ) 0.07 Nm (0.25 Nm )
Travel diagrams Group 5 Group 4
All measures in the drawings are in mm

Loose actuators All measures in the drawings are in mm

IMPORTANT: These loose actuators can be used with items of series LR, LM, LX, LZ and LK only.

Technopolymer roller Technopolymer roller Adjustable square rod, Adjustable round rod Technopolymer roller
Flexible rod with pointed end
Ø 18 mm Ø 18 mm 3x3x125 mm Ø 3x125 mm Ø 20 mm

3x3x125 Ø 3x125
5 11.2 0.2 8.3 15 24
55

19 - 116

5.4 5.4
20
19 -116

4.5 5 4.5 5
18

18
106

7
40
35

35

M4

M4
M4
M4

M4
M4

2.5 11.5

AC-CAE30 AC-CAE31 AC-CAE33 AC-CAE34 AC-CAE50 AC-CAE51

Technopolymer roller Technopolymer roller Adjustable actuator with Adjustable safety actuator with Technopolymer roller
Porcelain roller Adjustable fiber glass rod
Ø 20 mm Ø 20 mm technopolymer roller technopolymer roller Ø 20 mm

Ø6x200
2.5 11.5 1 10 1 10
20
20

1 10
7 5 13.5 11 20 10 6.5
20
20

20

19 - 189
34 - 93

Ø9
7 7
34 - 93
57

43
40

7
M4

M4
M4
80

7
49

M4

M4
M4

M4

AC-CAE52 AC-CAE53 (2)

CA-CAE54 AC-CAE55 (1)
AC-CAE56 AC-CAE57 AC-CAE69

- (1) Actuator AC-CAE55 can only be used in safety applications if adjusted to its max. length, as shown in figure beside. If you need an adjustable
lever for safety applications, use the adjustable safety lever AC-CAE56.
- (2) The position switch obtained by assembling switch LM •A38-20 (e.g. LMC5A38‑20, LMC6A38‑20…) with actuator AC-CAE53 will not
93

present the same travel diagrams and actuating forces as switch LM •A53‑J0ST (e.g. LMC5A53‑J0ST, LMC6A53‑J0ST…).
- (4) The actuator cannot be rotated to the inside because it will mechanically interfere with the switch head.

www.imopc.com
TECHNICAL DATASHEET

Special loose actuators All measures in the drawings are in mm

IMPORTANT: These loose actuators can be used with items of series LR, LM, LX, LZ and LK only.

Stainless steel rollers, Ø 20 mm

1 10 1 10

20
20
1 10
0.8 9.5 15 24 7 5 13.5 11 20

20
20
7

20

34 - 93
20
20

7 7

34 - 93

43
40
7

M4

M4
7 7
40

49
36

M4

M4
M4

M4
M4

AC-CAE31-R24 AC-CAE51-R24 AC-CAE52-R24 AC-CAE54-R24 AC-CAE55-R24 (1)

AC-CAE56-R24 AC-CAE57-R24

Technopolymer rollers, Ø 35 mm
0.8 9.5 0.8 9.5
7 7

35
8 9.5

35
24 10.8 19.5
9.5 7 13.5 7
7 7 7
35

35

35
35

43.5 - 101
35

41.3 - 101.3
47.5
43.5

47.5

50.5
M4
56.1
M4

M4
M4

M4

M4
M4

AC-CAE31-R25 (4)
AC-CAE51-R25 (4)
AC-CAE52-R25 AC-CAE54-R25 (4)
AC-CAE55-R25 (1)
AC-CAE56-R25 AC-CAE57-R25

Rubber rollers, Ø 40 mm
3 12 3 12
10 10
12
40

40
22
11.5 26 10 16
10 10
10 10
52.5 - 103.5
40

40
40

50 - 103.8
40
40

59

53
46

50

50

M4
M4
M4

M4

M4

M4
M4

AC-CAE31-R5 (4)
AC-CAE51-R5 (4)
AC-CAE52-R5 AC-CAE54-R5 (4)
AC-CAE55-R5 (1)
AC-CAE56-R5 AC-CAE57-R5 (4)

Rubber rollers, Ø 50 mm
3 12 3 12
10 10
50
50

12
26 16 22
10 10 10
50

50
50

10
50

58.5 - 108

58.8 - 108
55

58
64

55
M4

M4

M4

M4
M4

M4

AC-CAE51-R26 (4)
AC-CAE2-R26 (4)
AC-CAE54-R26 (4)
AC-CAE55-R26 (1)
AC-CAE56-R26 AC-CAE57-R26 (4)

Protruding rubber rollers, Ø 50 mm

11.4 - 26.4 20 - 35 11.4 - 26.4 20 - 35
50

50
58.5 - 108

58.8 - 108

10 10
M4

M4

AC-CAE55-R27 (1)
AC-CAE56-R27

www.imopc.com
TECHNICAL DATASHEET

Maximum and minimum actuation speed

Lever with roller - Type 1 Plunger with roller - Type 2
V V
Vmax Vmin Vmin Vmax Vmin Vmin
Ø (m/s) (mm/s) (mm/s) Ø (m/s) (mm/s) (mm/s)

Ø
L R Ø L R Ø

15° 2.5 9 15° 1 4 0.04

30° 1.5 8 30° 0.5 2 0.02
0.07
45° 1 7 45° 0.3 1 0.01

Ø
60° 0.75 7 Ø
Plunger with roller - Type 5

Lever with roller - Type 3 Vmax Vmin Vmin

Ø (m/s) (mm/s) (mm/s)
Ø
Vmax Vmin Vmin L R
Ø (m/s) (mm/s) (mm/s)
15° 0.3 4 0.04
L R Ø
30° 0.2 2 0.02
15° 1 5 0.05

Ø
Ø
30° 0.5 2.5 0.025
V

45° 0.3 1.5 0.015 Plunger with roller - Type 4

Vmax Vmin Vmin

Contacts Type:
V (m/s) (mm/s) (mm/s)
L R

V
R = snap action
Ø

Ø 0.5 1 0.01
L = slow action
Ø

Driving Torques For LR and LX series only

Cover screws 0.8...1.2Nm

Head screws 0.8...1.2Nm
Lever screws 0.8...1.2Nm
Protection plugs (conduit entry M20/PG13.5) 1.2...1.6Nm
(conduit entry M16/PG11) 1.0...1.4Nm
Contact block screws 0.6...0.8Nm
M5 screws of the housing fastening with washer 2.0...3.0Nm

www.imopc.com
TECHNICAL DATASHEET

Travel Diagrams

Contact block Group 1 Group 2 Group 3 Group 4

3 4.5 6.9 40°
6 0 1 6 0 1.5 8 0 2.3 13 0 15° 75°
1NO+1NC R1 R1.5 R2.3 R15°

4.4 6.6 10.113 59°75°

9 0 1 6 0 1.5 8 0 2.3 0 15°
2NC R1 R1.5 R2.3 R15°

0 1 6 0 1.5 8 0 2.3 13 0 15° 75°

10
2NO R1 R 1.5 R 2.3 R 15°

0 1 3 6 1.5 4.5 6.9 0 15° 40° 75°

20 0 8 0 2.3 13
1NO+2NC R1 R1.5 R2.3 R15°

0 1 3 6 1.5 4.5 6.9 40°

21 0 8 0 2.3 13 0 15° 75°
3NC R1 R1.5 R2.3 R15°

0 1 3 6 1.5 4.5 6.9 40°

22 0 8 0 2.3 13 0 15° 75°
2NO+1NC R1 R1.5 R2.3 R15°

3 4.5 6.9 40°

33 0 1 6 0 1.5 8 0 2.3 13 0 15° 75°
1NO+1NC R1 R1.5 R2.3 R15°

3 4.5 6.9 40°

34 0 1 6 0 1.5 8 0 2.3 13 0 15° 75°
2NC R1 R1.5 R2.3 R15°

0 1 6 0 1.5 8 0 2.3 13 0 15° 75°

2
2x(1NO-1NC) R1 R1.5 R2.3 R15°

Legend
Closed contact ! Opened contact | Positive opening travel | Pushing the switch / Releasing the switch

www.imopc.com
TECHNICAL DATASHEET

Group 7
Contact block Group 1 Group 2 Group 3 Group 4 Group 5 Group 6
inverted contacts
0 1.3 6 0 2 8 0 3 13 0 9° 0 17° 75° 0 17° 75° 0 5.4 8
2
2x(1NO-1NC) 0.7
1.1 1.6 4° 10° 10° 4.8
0 1.3 6 0 2 8 0 3 13 0 9° 0 0 3.4 8
17° 75° 17° 75° 0
3
1NO-1NC 0.8 4° 2.9
1.2 1.8 10° 10°
0 2.2 4 6 0 3.3 6 8 0 5.1 9.2 13 0 17° 0 30° 60° 75° 0 25° 55° 75° 0 3.8 8
5
1NO+1NC 1.1 6° 5
1.7 2.5 15° 10°
0 1.5 3 3.5 6 4.5 0 3.5 6.9 13 0 20° 40° 75° 0 15° 35° 75° 0 4.6
6 0 2.3 8
/
8

1NO+1NC 3.1 4.7 7.1 42° 35° 3

4.6 6 6.9 8 10.6 13 0 41° 61° 75° 56° 75° 3 8

7 0 3.1 0 4.7 0 7.1
/
0 36° 0

1NO+1NC 1.6 2.4 3.7 22° 17° 4.5

9 0 2.9 4.4 6 0 4.4 6.6 8 0 6.7 10.1 13

/ 0 39° 59° 75° 0 34° 54°75° 0 3.1 8
2NC

10 0 1.4 6 0 2.1 8 0 3.2 13 0 10° 0 20° 75° 0 15° 75° 0 4.6 8

2NO
0 2 4 6 6 4.6 9.2 13 56° 75° 0 5.6 8
3 8 0
11 0
/
0° 26°
/
2NC 0.6 0.9 1.4 4
7°
0 2.9 6 0 4.4 8 0 6.7 13 0 21° 0 37° 75° 0 32° 75° 0 4.7 8
12
2NO 1.5 3.5 19° 14°
2.3 8° 3.3
0.8 2.3 0 3.5 0 5.3 0 11° 31° 6° 26°
1.2 8 1.8 13 75° 75° 0 3.1
13 /
8
0
2NC 3 4.5 6 4.5 6.8 6.9 10.4 40° 60° 0 35° 55° 5.3

0 1.4 2.9 6 0 2.1 4.4 8 3.2 6.7 39° 0 14° 34° 75° 3
14 13
/
0 19° 75° 0 8
2NC 3 4.5 4.5 6.8 0 6.9 10.4 60° 35° 55° 4.7
40°
0 1.4 6 2.1 0 3.2 13 19° 0 14° 75°
15 0 8
/
0 75° 0 4.7 8
2NO 3 4.5 6.9 40° 35° 3.1
0 28° 48°
16 / / / /
75°
/ /
2NC 48° 28° 75°

0 1.5 3 6 4.5 6.9 13 0 10° 40° 0 15° 35° 75° 0 4.6 8

18 0 2.3 8 0 3.5 0 20° 75°
1NO+1NC 2 3 4.6 14° 27° 22° 4.1

0 1.5 3 6 0 2.3 4.5 8 0 3.5 6.9 13 0 10° 0 20° 40° 75° 0 15° 35° 75° 0 4.6 8
20
1NO+2NC 2 3 4.6 14° 27° 22° 4

21 0 1.5 3 6 0 2.3 4.5 8 0 3.5 6.9 13 0 10° 0 20° 40° 75° 0 15° 35° 75° 0 4.6 8
3NC

0 1.5 3 6 0 2.3 4.5 8 0 3.5 6.9 13 0 10° 0 20° 40° 75° 0 15° 35° 75° 0 4.6 8
22
2NO+1NC 14° 4.1
2 3 4.6 27° 22°

0 1.5 3 4.5 6 0 2.3 4.56.5 8 0 3.5 6.910.2 13 0 20° 40°58° 75° 0 15° 35°53° 75° 0 1.8 4.6 8
28 /
1NO+2NC 2 3 4.6 27° 22° 4
5.5 7.5 12.5 70° 65°

0 1.5 3 6 0 2.3 4.5 8 0 3.5 6.9 13 0 20° 40° 75° 0 15° 35° 75° 0 4.6 8
29 /
3NC 4.5 6.5 10.2 58° 53° 1.8
5.5 7.5 12.5 70° 65°

0 1.5 3 6 0 2.3 4.5 8 0 3.5 6.9 13 0 20° 40° 75° 0 15° 35° 75° 0 4.6 8
30 /
3NC 4.5 6.5 10.2 58° 53° 1.8
5.5 7.5 12.5 70° 65°

4.5
33 0 1.5 3 6 0 2.3 8 0 3.5 6.9 13 0 10° 0 20° 40° 75° 0 15° 35° 75° 0 4.6 8
1NO+1NC 2 3 4.6 14° 25° 20° 4.3

34 0 1.5 3 6 0 2.3 4.5 8 0 3.5 6.9 13 0 10° 0 20° 40° 75° 0 15° 35° 75° 0 4.6 8
2NC
0 3.4 4.9 6 0 5.2 7.4 8 7.8 11.2 13 0 45° 65° 75° 0 40° 60° 75° 0 2.8 8
37 0
/
1NO+1NC 1.5 2.3 3.4 18° 13° 4.9

66 0 1.4 2.9 6 0 2.1 4.4 8 0 3.2 6.7 13 0 10° 0 19° 39° 75° 0 14° 34° 75° 0 3 8
1NC

67 0 1.4 6 0 2.1 8 0 3.2 13 0 10° 0 20° 75° 0 15° 75° 0 4.6 8

1NO

Legend
Closed contact ! Opened contact | Positive opening travel | Pushing the switch / Releasing the switch

Ref:LR-Pos-Switch-Dec15v1 Errors and omissions excepted. Subject to change without notice. www.imopc.com