10. Click Next to proceed the installation process.

Click Go to set
I. Install and configure computer systems
11. For Server PC, set password to “Css@123”.Click Next and On the Administration tab, look for the LANParameters and type
a. Disassemble/ Assemble computer parts the system will restart. the IP Address of your preference:
12. On your Client PC's Create an account for thisPC screen,
b. Create a bootable media using Rufus type your first name (ex. Helner) as the Username and leave the
1. Open Rufus and choose the Device (USB Flash Drive) which should password text field blank.
be used as your bootable media. 13. Click Next and the installation is complete.
2. Choose the MBR partition scheme for BIOS or UEFI and leave the
File System and Cluster Size to default settings and label the drive. e. Install appropriate drivers (both PC)
3. Check to Create a bootable disk and ensure that the ISO Image is NOTE: The IP address for your router can range from 10.0.0.0to
selected from the drop-down, use the smalldrive icon to locate and 10.255.255.255, 172.16.0.0 to 172.31.255.255, or
choose the image.
f. Install the following application software 192.168.0.0 to 192.168.255.255.
4. Choose Start and wait for the Rufus to properly load ISOto your USB CLIENT PC Click OK
Flash Drive. - PDF Reader Click OK to save changes and rebootClick
- WinRar the close icon
- VLC Player On the Internet Settings tab, select the radio button on
c. Set boot sequence into the BIOS - USB Guard
1. Turn on or restart your computer. Universal Repeater
2. Press Del or F2 to access the BIOS Setup Utility. Look for the SSID/ WiFi Name that you want to connect On the Enter
3. Look for an option to change the boot order, it might be under a menu
II. Setup Computer Networks Password screen, type the WiFi passwordClick Connect then wait
option called Boot, Boot Options, Boot Sequence or Advanced a. Network layout diagram for the rebooting process tocomplete
Options. Click the close icon
4. Change the list order so that the USB Device or b. T568-A or T568-B cable using your designed networklayout with
Reset the router (WAP)
Removable Devices is listed first. the ff cable measurements:
5. Navigate to the Save and Exit or Exit menu and choosean option that Open a web browser and access your router’s web-based setup
DESCRIPTION CABLE MEASUREMENT
says, “Save Changes” or “Exit with Changes Saved” page (ex: 192.168.0.1)
2 Client/Server (PC)
6. Confirm the changes and exit BIOS by selecting Yes. Select the radio button on DHCP
to Modular Box approx. 2m2
7. The computer will automatically restart once you exit BIOS. Fill-in the following data, example:
Client/Server
WiFi Name: Firstname
(Modular Box) to
WiFi Password: Css@12345
d. Install Operating System Patch Panel approx. 1m2
Click OK
1. Insert Windows 10/ Windows Server 2016 installation USB into your Client/Server
Click Go to set
Client/ Server computer. (Patch Panel) to Hub approx. 0.5m
On the Internet Settings tab, select the radio button on
2. Boot the PC to BIOS and modify the boot sequence to boot first from 1 Router to Patch Panel approx. 0.5m1
AP Mode
USB. Save your changes and restart yourPC. (Router’s) Patch Panel
Click OK
3. If you receive a prompt to boot from USB, click any key to Hub approx. 0.5m
1 Wireless Access Point Click OK to save changes and rebootClick
to continue. the close icon
4. When Windows 10 setup starts, click Next. (WAP) approx. 0.5m
5. Click Install Now. 1 (WAP) Patch Panel to
6. Check the I accept the license terms agreement. Then,click Next. Hub approx. 0.5m d. Set-up Network Firewall
7. On the Which type of installation do you want screen, Select Right click on the network icon and select Open Network& Sharing
Center
Custom: Install Windows only (advanced). c. Configure the router’s IP address, Universal Repeaterand WAP
8. On the Where do you want to install Windows screen,delete all On the Network and sharing center screen, click
settings Windows Firewall
existing partitions. To create a partition, select the disk (Unallocated). Reset the Router
Select the capacity of your partition based on your preference: On the Windows Firewall screen, click Turn WindowsFirewall On/Off
Open a web browser and access your router’s web-based Make sure that both Private and Public NetworkSetting is turned
- C: 60%, D: 40% setup page (ex: 192.168.0.1)
- C: 70%, D: 30% on
Select the radio button on DHCP Click OK
- C: 50%, D: 50% Fill-in the following data, example:WiFi
9. Then click New. Name: Lastname
WiFi Password: Css@12345
Click OK
 Type ping followed by an IP address that you want to testthe connectivity
III. Setup Computer Servers
(ex: ping 192.168.0.100)
a. Set workgroup and computer description Hit the enter key.
Click Window’s ExplorerRight
click on This PC Click
Properties
Click Change settings
On the Computer description textbox, type “Client” –ifclient PC
and “Server” –if server PC
Click the Change… button
On the Computer name textbox, for Client PC rename itto your first
name (ex. Helner) and for Server PC rename it to your last name (ex.
Taghap)
Change Workgroup to your preference (ex: ANHS)Click OK
Click OK to apply all the changes and then a system reboot is required

b. Use Class A/B/C static IP Address on SERVER andDynamic IP

Address on CLIENT
SERVER PC
Right click on the network icon and select Open Network& Sharing
Center
On the Network and sharing center screen, click
Change adapter settings or Ethernet
Double click Ethernet
Click Properties
Double click Internet Protocol Version 4 (TCP/IPv4)
Select the radio button on Use the following IP Addressand input the
following IP Address (see example below) based on your preference:

Click OK
Click OK
Click Close

On the Network and sharing center screen, click

Change advanced sharing settings
On the Advanced sharing settings screen, TURN ONeverything
except the Password protected sharing Click Save changes

c. Testing of connectivity between CLIENT and SERVERusing PING

command
BOTH SERVER AND CLIENT
On the search bar, type “cmd”Hit the
Enter key
Type ipconfig to display the IP address assigned to eachPC
Hit the Enter key