SCC 25 - 40 - 35M Span DN - 102a

CLIENT:
BIHAR STATE ROAD DEVELOPMENT

CORPORATION LTD.
PROJECT TITLE:
CONSTRUCTION OF ELEVATED ROAD

CORRIDOR FROM AIIMS (ON NH-98) TO
DIGHA (ON GANGA PATH) AT PATNA IN THE
STATE OF BIHAR
COTRACTOR:
GAMMON INDIA LIMITED
TITLE OF CALCULATION:
SPAN P143-P144-P153-P154
DESIGN OF SCC SUPERSTRUCTURE (25+40+25 M SPAN)
(CHECK WITH EXTRADOSE CABLES)
Note No: 1504/P143_P155/DN-102A Prepared By:
Revision No: R0 No. of Sheets 1+ Checked By:
Date: Sep‐15 Approved By:
Date Rev No. Revision By
CONSULTANT:
CDS CONSULT (I) PVT. LTD.
PLOT NO. 537, SECTOR-31, GURGAON-122001
Tel: 0124-4032863; Fax: 0124 4032864; Email: [email protected]
SPAN P143‐P144‐P153‐P154
CONTENTS
1 GENERAL
2 SECTION PROPERTIES
3 LOADS
4 TABULATION OF BENDING MOMENT AND SHEAR FORCE
5 CALCULATION OF STRESSES DUE TO TEMP GRADIENT
6 CALCULATION OF STRESSES DUE TO DIFF SHRINKAGE
7 FLEXURE AND SHEAR CHECK
8 DESIGN OF SHEAR CONNECTORS
9 DESIGN OF CROSS GIRDERS
10 DESIGN OF SPLICES AND WEB STIFFNERS
11 DEFLECTION CHECK AND PRECAMBER CALCS
12 FORCES AND MOVEMNTS ON BEARINGS
13 DESIGN OF BEARING STIFFENERS
14 DESIGN OF BRACINGS
15 DESIGN OF DECK SLAB
Apdx A STADD INPUT FILES
Page 1 of 156
1 GENERAL
These calaculations pertain to design of 3 span continuous (25+40+25m) Steel Concrete Composite
superstructure. The superstructure has been idealised as grillage and analysed using STAAD Pro software.
Grillage mesh showing member numbers and node numbers are shown subsequently in Appendix A. 4 nos.
4K15 external cables are provided at continuous supports (passing through Pylons resting on pier cap) to give a
look of extradosed bridge. The cables are also modelled in the staadpro and their effects have been
considered on superstructure. However, the superstructure is also checked without the effect of cables. These
calculations pertain to the design with extradosed cables.
Following codes have been adopted for designs.
IRC 6‐ 2010
IRC 22 ‐2008
IRC 24 ‐ 2010
Basic Design Data
Overall span (Centre to centre Pier) 25 +40 +25 m
Effective span 25‐1*0.6 24.40 +40 +24.4 m
Skew Angle 0.000 deg
No of Long girders 6.000
c/c spacing between girders 2.240 m
Dist between brg and exp joint 0.600 m
Dist between brg to girder end 0.300 m
Deck slab cantilever 0.800 m
Width of deck slab 12.800 m (incl extended deck slab)
Depth of Steel Girders 1.800 at mid 1.800 m at
Overall depth including slabs 2.050 span 2.050 m support
Thick. Of deck slab 0.200 m
Thick. Of deck slab at exp joint 0.250 m
Thick of wearing coat 0.065 m
Material
Concrete
Concrete Grade M50
E value 35000 mpa Table 6.5 of IRC 112
0
Density of concrete 2.5 t/m3 Coeff. Of therm. exp 1.20E-05 / C
Structural Steel (IS:2062)
All components other than Studs
Grade used E250 (Fe410 W)
Yield stress 250 240 and 230 mpa
For plate thickness <20 20‐40 >40 mm
E value 200000 mpa (Cl 502.2.2 of IRC 24‐2010)
Density 7.85 t/m3
Studs
Grade used Fe540 B
Yield stress 390.0 mpa
E value 200000 mpa (Cl 502.2.2 of IRC 24‐2010)
Page 2 of 156
Reinforcing Steel
Grade used Fe500 (IS 1786)
Welds (Clause 512.4 of IRC 24‐2010)
Type of weld Fillet
Grade used Fe 510 W‐HT
Compliance of code IS 2062‐2006
Electrode designation EXXX‐43X
Permissible shear stress 108.0 mpa
GENERAL CONSIDERATIONS
Min overall depth of pl girder L/25 = 0.98 m 504.4 (b)
Max depth of girder 3 x spacing = 6.72 m 504.4 (b)
Minimum spacing between outermost girders L/20 = 1.22 m 504.3
Min thickness of plates 504.7.1 (a) 8.0 mm (If protected against corrosion)
504.7.1 (b) 10.0 mm (If not protected against corrosion)
Min thickness of packing plates 504.7.2 1.5 mm
Min Section of angles 504.7.3 75x50 for main members in inverted construction
504.7.4 65x45 for all other cases
Min width of plates 504.7.4 50 mm
Min th Of angle connecting stringer to cross girder 3/4 th of stringer thickness 504.7.5
Min thickness of angle connecting cross girder to main girder 3/4 th of X Girder thickness 504.7.5
Min thickness of web plates As per cl 509.6 of IRC 24‐2010
modular ratio 200000/35000= 5.71 < 7.5
adopt 7.5
Creep factor (Kc) 0.5
Modular ratio for permanent loadings m/Kc = 15
Modular ratio for transient loadings 7.5
Effective width of flange over continuous support
c/c distance between girders 'B' 2.24
L1/L2 24.4 40
B/L 0.092 0.056
X for outer girders 0.3
ψ (Table 4 of IRC 22:2008)
Span Value of L/2 3L/8 L/4 L/8 SUPP
40 m span 25 m span
ψ 0.88 0.79 0.71 0.57 0.44

Eff w OG 1.205 1.089 0.973 0.788 0.602
Eff w IG 1.963 1.774 1.586 1.283 0.981
ψ 0.95 0.89 0.83 0.69 0.56
Eff w OG 1.304 1.222 1.141 0.955 0.769
Eff w IG 2.124 1.991 1.858 1.556 1.254
Page 3 of 156
2 SECTION PROPERTIES
OUTER GIRDER ‐END L/2 SPAN SECTION (0 TO 12.2M FROM END SUPPORT)
596 982 Component b t
200 200 deck slab 1578 200
Wedge Left 0 0
836X50 Wedge Centre 836 50
Wedge Right 0 0
1800 14 top plate 1 0 0
top plate 2 600 25
Bottom plate 1 600 25
Bottom plate 2
Web plate 14 1750
b Total Depth 2050.0 mm
Calculation of Ixx ψ = 1.000 ω = 0.500
av thick of slab 0.226 m ecc from top 0.115 m
S No. No. A y Ay Ay2 I0 I0+Ay2
1. Deck slb (T Load) 1 0.0421 1.950 0.082 0.160 0.000 0.160
2. Deck slab (P Load) 1 0.0210 1.950 0.041 0.080 0.000 0.080
3. Deck Wdg (T)
Wedge Left 1 0.0000 1.850 0.000 0.0000 0 0.0000
Rect wedge at centre 1 0.0056 1.825 0.010 0.0186 1.16E‐06 0.0186
Wedge Right 1 0.0000 1.850 0.000 0.0000 0 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.0000 1.850 0.000 0.000 0 0.000
Wedge Right 1 0.0000 1.850 0.000 0.000 0 0.000
5a. Top Fl plate 1 1 0.0000 1.800 0.000 0.000 0 0.000
5b. Top Fl plate 2 1 0.0150 1.788 0.027 0.048 7.81E‐07 0.048
6. Web Plate 1 0.0245 0.900 0.022 0.020 0.006 0.026
7a. Bott Fl plate 1 1 0.0150 0.013 0.000 2.34E‐06 7.81E‐07 3.13E‐06
7b. Bott Fl plate 2 1 0.0000 0.0000 0.000 0 0 0
7C. TOP Fl holes 1 ‐0.0039 1.7875 ‐0.007 ‐0.01246 ‐2E‐07 ‐0.01246
7D. Bott Fl holes 1 ‐0.0039 0.0125 0.000 ‐6.1E‐07 ‐2E‐07 ‐8.1E‐07
Section Properties at Splice Locations (Holes deducted)
Comp Sect (T loading) Σ 0.0943 0.1342 0.2338 0.0064 0.2402
Comp Sect (P loading) Σ 0.0705 0.0881 0.1446 0.0063 0.1509
Girder Alone Σ 0.0467 0.0420 0.0553 0.0063 0.0616
ΣA ΣAy ΣAy2 ΣI0 Σ(I0+Ay2)
Section Properties at other location (No Holes deducted)
Girder Alone Σ 0.0545 0.0491 0.0678 0.0063 0.0740
Page 4 of 156
Calculation of Iyy Left side z (+ve) Right side z (‐ve)
S No. No. A z Az Az2 I0 I0+Az2

1. Deck slb (T Load) 1 0.042 ‐0.193 ‐0.008 0.002 0.0087 0.0103
2. Deck slab (P Load) 1 0.021 ‐0.193 ‐0.004 0.001 0.0044 0.0051
3. Deck Wdg (T)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Rect wedge at centre 1 0.006 0.178 0.001 0.000176 0.000325 0.000501
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Rect wedge at centre 1 0.003 0.178 0.000 8.82E‐05 0.000162 0.000251
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
5a. Top Fl plate 1 1 0.000 0 0.000 0 0.0000 0.0000
5b. Top Fl plate 2 1 0.015 0 0.000 0 0.0005 0.0005
6. Web Plate 1 0.025 0 0.000 0 4E‐07 0.0000
7a. Bott Fl plate 1 1 0.015 0 0.000 0 0.000 0.0005
7b. Bott Fl plate 2 1 0.000 0 0.000 0 0.000 0.0000
Comp Sect (T loading) Σ 0.102 ‐0.007 0.002 0.010 0.012
Comp Sect (P loading) Σ 0.078 ‐0.004 0.001 0.005 0.006
Girder Alone Σ 0.055 0.000 0 0.001 0.001
ΣA ΣAz ΣAz2 ΣI0 Σ(I0+Az2)
Section Properties with holes without holes

Item Girder Comp (T) Comp (P) Girder Comp (T) Comp (P)
Area ΣA 0.0467 0.094 0.071 0.0545 0.102 0.078
CG frm bot fibre 'y' Yb = ΣAy/ΣA 0.900 1.423 1.250 0.900 1.383 1.215
Mom of Inertia Ix = Σ(I0+Ay2)‐ΣAy2 0.024 0.049 0.041 0.030 0.057 0.048
CG from web cntr 'z' Zw = ΣAz/ΣA 0.000 ‐0.070 ‐0.045 0.000 ‐0.070 ‐0.045
Mom of Inertia Iy = Σ(I0+Az2)‐ΣAz2 0.001 0.011 0.006 0.001 0.011 0.006
Torsional Constant 0.0001 0.0001 0.0001 0.000 0.000 0.000
Yt ‐ 0.627 0.800 ‐ 0.667 0.835
Yi 0.900 0.377 0.550 0.900 0.417 0.585
Yb 0.900 1.423 1.250 0.900 1.383 1.215
Zt ‐ 0.079 0.051 ‐ 0.086 0.057
Zi 0.026 0.131 0.074 0.033 0.138 0.082
Zb 0.026 0.035 0.033 0.033 0.041 0.039
Page 5 of 156
OUTER GIRDER ‐SECTION AT 5L/8 (I.E. 15.25M FROM END SUPPORT)
200 200 deck slab 1426 200
Wedge Left
779x50 Wedge Centre 779 50
Wedge Right
1800 14 top plate 1
top plate 2 600 25
b Bottom plate 1 600 25
Bottom plate 2
Web plate 14 1750
Total Depth 2050.0 mm
1. Deck slb (T Load) 1 0.0380 1.950 0.074 0.145 0.000 0.145
2. Deck slab (P Load) 1 0.0190 1.950 0.037 0.072 0.000 0.072
3. Deck Wdg (T)
Wedge Left 1 0.0000 1.850 0.000 0.0000 0 0.0000
Wedge Right 1 0.0000 1.850 0.000 0.0000 0 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.0000 1.850 0.000 0.000 0 0.000
Wedge Right 1 0.0000 1.850 0.000 0.000 0 0.000
5a. Top Fl plate 1 1 0.0000 1.800 0.000 0.000 0 0.000
5b. Top Fl plate 2 1 0.0150 1.788 0.027 0.048 7.81E‐07 0.048
6. Web Plate 1 0.0245 0.900 0.022 0.020 0.006 0.026
7b. Bott Fl plate 2 1 0.0000 0.0000 0.000 0 0 0
7C. TOP Fl holes 1 ‐0.0039 1.7875 ‐0.007 ‐0.01246 ‐2E‐07 ‐0.01246
Girder Alone Σ 0.0467 0.0420 0.0553 0.0063 0.0616
ΣA ΣAy ΣAy2 ΣI0 Σ(I0+Ay )
2

Girder Alone Σ 0.0545 0.0491 0.0678 0.0063 0.0740
2
Page 6 of 156

1. Deck slb (T Load) 1 0.038 ‐0.174 ‐0.007 0.001 0.0064 0.0076
2. Deck slab (P Load) 1 0.019 ‐0.174 ‐0.003 0.001 0.0032 0.0038
3. Deck Wdg (T)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
5a. Top Fl plate 1 1 0.000 0 0.000 0 0.0000 0.0000
5b. Top Fl plate 2 1 0.015 0 0.000 0 0.0005 0.0005
6. Web Plate 1 0.025 0 0.000 0 4E‐07 0.0000
7a. Bott Fl plate 1 1 0.015 0 0.000 0 0.000 0.0005
7b. Bott Fl plate 2 1 0.000 0 0.000 0 0.000 0.0000
Girder Alone Σ 0.055 0.000 0 0.001 0.001

Area ΣA 0.0467 0.090 0.068 0.0545 0.098 0.076
Mom of Inertia Ix = Σ(I0+Ay2)‐ΣAy2 0.024 0.048 0.040 0.030 0.056 0.047
Iy = Σ(I0+Az )‐ΣAz
2 2
Mom of Inertia 0.001 0.009 0.005 0.001 0.009 0.005
Yt ‐ 0.653 0.823 ‐ 0.692 0.856
Yi 0.900 0.403 0.573 0.900 0.442 0.606
Yb 0.900 1.397 1.227 0.900 1.358 1.194
Zt ‐ 0.074 0.048 ‐ 0.081 0.054
Zi 0.026 0.119 0.069 0.033 0.126 0.077
Zb 0.026 0.034 0.032 0.033 0.041 0.039
Page 7 of 156
200 200 deck slab 1274 200
Wedge Left
Wedge Right
1800 14 top plate 1
top plate 2 600 25
Bottom plate 2
Web plate 14 1750
1. Deck slb (T Load) 1 0.0340 1.950 0.066 0.129 0.000 0.129
2. Deck slab (P Load) 1 0.0170 1.950 0.033 0.065 0.000 0.065
3. Deck Wdg (T)
Wedge Left 1 0.0000 1.850 0.000 0.0000 0 0.0000
Rect wedge at centre 1 0.0048 1.825 0.009 0.0160 1E‐06 0.0160
Wedge Right 1 0.0000 1.850 0.000 0.0000 0 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.0000 1.850 0.000 0.000 0 0.000
Wedge Right 1 0.0000 1.850 0.000 0.000 0 0.000
5a. Top Fl plate 1 1 0.0000 1.800 0.000 0.000 0 0.000
5b. Top Fl plate 2 1 0.0150 1.788 0.027 0.048 7.81E‐07 0.048
6. Web Plate 1 0.0245 0.900 0.022 0.020 0.006 0.026
7b. Bott Fl plate 2 1 0.0000 0.0000 0.000 0 0 0
7C. TOP Fl holes 1 ‐0.0039 1.7875 ‐0.007 ‐0.01246 ‐2E‐07 ‐0.01246
Girder Alone Σ 0.0467 0.0420 0.0553 0.0063 0.0616
2

Girder Alone Σ 0.0545 0.0491 0.0678 0.0063 0.0740
2
Page 8 of 156

1. Deck slb (T Load) 1 0.034 ‐0.156 ‐0.005 0.001 0.0046 0.0054
2. Deck slab (P Load) 1 0.017 ‐0.156 ‐0.003 0.000 0.0023 0.0027
3. Deck Wdg (T)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
5a. Top Fl plate 1 1 0.000 0 0.000 0 0.0000 0.0000
5b. Top Fl plate 2 1 0.015 0 0.000 0 0.0005 0.0005
6. Web Plate 1 0.025 0 0.000 0 4E‐07 0.0000
7a. Bott Fl plate 1 1 0.015 0 0.000 0 0.000 0.0005
7b. Bott Fl plate 2 1 0.000 0 0.000 0 0.000 0.0000
Girder Alone Σ 0.055 0.000 0 0.001 0.001

Area ΣA 0.0467 0.085 0.066 0.0545 0.093 0.074
Ix = Σ(I0+Ay )‐ΣAy
2 2
Mom of Inertia 0.024 0.047 0.038 0.030 0.054 0.045
2 2
Mom of Inertia 0.001 0.006 0.004 0.001 0.006 0.004
Yt ‐ 0.681 0.846 ‐ 0.720 0.879
Yi 0.900 0.431 0.596 0.900 0.470 0.629
Yb 0.900 1.369 1.204 0.900 1.330 1.171
Zt ‐ 0.068 0.045 ‐ 0.075 0.052
Zi 0.026 0.108 0.065 0.033 0.116 0.072
Zb 0.026 0.034 0.032 0.033 0.041 0.039
Page 9 of 156
200 200 deck slab 1031 200
Wedge Left
Wedge Right
1800 14 top plate 1
top plate 2 600 25
Bottom plate 2
Web plate 14 1750
1. Deck slb (T Load) 1 0.0275 1.950 0.054 0.105 0.000 0.105
2. Deck slab (P Load) 1 0.0137 1.950 0.027 0.052 0.000 0.052
3. Deck Wdg (T)
Wedge Left 1 0.0000 1.850 0.000 0.0000 0 0.0000
Wedge Right 1 0.0000 1.850 0.000 0.0000 0 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.0000 1.850 0.000 0.000 0 0.000
Wedge Right 1 0.0000 1.850 0.000 0.000 0 0.000
5a. Top Fl plate 1 1 0.0000 1.800 0.000 0.000 0 0.000
5b. Top Fl plate 2 1 0.0150 1.788 0.027 0.048 7.81E‐07 0.048
6. Web Plate 1 0.0245 0.900 0.022 0.020 0.006 0.026
7b. Bott Fl plate 2 1 0.0000 0.0000 0.000 0 0 0
7C. TOP Fl holes 1 ‐0.0039 1.7875 ‐0.007 ‐0.01246 ‐2E‐07 ‐0.01246
Girder Alone Σ 0.0467 0.0420 0.0553 0.0063 0.0616
2

Girder Alone Σ 0.0545 0.0491 0.0678 0.0063 0.0740
2
Page 10 of 156

1. Deck slb (T Load) 1 0.027 ‐0.126 ‐0.00347 0.000 0.0024 0.0029
2. Deck slab (P Load) 1 0.014 ‐0.126 ‐0.00173 0.000 0.0012 0.0014
3. Deck Wdg (T)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Rect wedge at centre 1 0.002 0.075 0.000 1.17E‐05 6.95E‐05 8.11E‐05
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
5a. Top Fl plate 1 1 0.000 0 0.000 0 0.0000 0.0000
5b. Top Fl plate 2 1 0.015 0 0.000 0 0.0005 0.0005
6. Web Plate 1 0.025 0 0.000 0 4E‐07 0.0000
7a. Bott Fl plate 1 1 0.015 0 0.000 0 0.000 0.0005
7b. Bott Fl plate 2 1 0.000 0 0.000 0 0.000 0.0000
Girder Alone Σ 0.055 0.000 0 0.001 0.001

Area ΣA 0.0467 0.078 0.063 0.0545 0.086 0.070
2 2
Mom of Inertia 0.024 0.044 0.036 0.030 0.051 0.043
2 2
Mom of Inertia 0.001 0.004 0.002 0.001 0.004 0.002
Yt ‐ 0.732 0.888 ‐ 0.770 0.917
Yi 0.900 0.482 0.638 0.900 0.520 0.667
Yb 0.900 1.318 1.162 0.900 1.280 1.133
Zt ‐ 0.060 0.041 ‐ 0.067 0.047
Zi 0.026 0.091 0.057 0.033 0.099 0.065
Zb 0.026 0.033 0.031 0.033 0.040 0.038
Page 11 of 156
OUTER GIRDER ‐SECTION AT CONT SUPPORT (I.E. 24.4 M FROM END SUPPORT)
200 200 deck slab 1007 200
Wedge Left
Wedge Right
1800 14 top plate 1
top plate 2 600 25
Bottom plate 2
Web plate 14 1750
1. Deck slb (T Load) 1 0.0269 1.950 0.052 0.102 0.000 0.102
2. Deck slab (P Load) 1 0.0134 1.950 0.026 0.051 0.000 0.051
3. Deck Wdg (T)
Wedge Left 1 0.0000 1.850 0.000 0.0000 0 0.0000
Wedge Right 1 0.0000 1.850 0.000 0.0000 0 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.0000 1.850 0.000 0.000 0 0.000
Wedge Right 1 0.0000 1.850 0.000 0.000 0 0.000
5a. Top Fl plate 1 1 0.0000 1.800 0.000 0.000 0 0.000
5b. Top Fl plate 2 1 0.0150 1.788 0.027 0.048 7.81E‐07 0.048
6. Web Plate 1 0.0245 0.900 0.022 0.020 0.006 0.026
7b. Bott Fl plate 2 1 0.0000 0.0000 0.000 0 0 0
7C. TOP Fl holes 1 ‐0.0039 1.7875 ‐0.007 ‐0.01246 ‐2E‐07 ‐0.01246
Girder Alone Σ 0.0467 0.0420 0.0553 0.0063 0.0616
2

Girder Alone Σ 0.0545 0.0491 0.0678 0.0063 0.0740
2
Page 12 of 156

1. Deck slb (T Load) 1 0.027 ‐0.123 ‐0.003 0.000 0.0023 0.0027
2. Deck slab (P Load) 1 0.013 ‐0.123 ‐0.002 0.000 0.0011 0.0013
3. Deck Wdg (T)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Rect wedge at centre 1 0.002 0.070 0.000 1.02E‐05 6.65E‐05 7.67E‐05
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
5a. Top Fl plate 1 1 0.000 0 0.000 0 0.0000 0.0000
5b. Top Fl plate 2 1 0.015 0 0.000 0 0.0005 0.0005
6. Web Plate 1 0.025 0 0.000 0 4E‐07 0.0000
7a. Bott Fl plate 1 1 0.015 0 0.000 0 0.000 0.0005
7b. Bott Fl plate 2 1 0.000 0 0.000 0 0.000 0.0000
Girder Alone Σ 0.055 0.000 0 0.001 0.001

Area ΣA 0.0467 0.078 0.062 0.0545 0.086 0.070
2 2
Mom of Inertia 0.024 0.044 0.036 0.030 0.051 0.043
2 2
Mom of Inertia 0.001 0.004 0.002 0.001 0.004 0.002
Yt ‐ 0.738 0.892 ‐ 0.775 0.921
Yi 0.900 0.488 0.642 0.900 0.525 0.671
Yb 0.900 1.312 1.158 0.900 1.275 1.129
Zt ‐ 0.059 0.041 ‐ 0.066 0.047
Zi 0.026 0.090 0.056 0.033 0.097 0.064
Zb 0.026 0.033 0.031 0.033 0.040 0.038
Page 13 of 156
OUTER GIRDER ‐SECTION AT L/8 OF 40M SPAN (I.E. 29.4M FROM END SUPPORT)
200 200 deck slab 1250 200
Wedge Left
Wedge Right
1800 14 top plate 1
top plate 2 600 25
Bottom plate 2
Web plate 14 1750
1. Deck slb (T Load) 1 0.0333 1.950 0.065 0.127 0.000 0.127
2. Deck slab (P Load) 1 0.0167 1.950 0.033 0.063 0.000 0.063
3. Deck Wdg (T)
Wedge Left 1 0.0000 1.850 0.000 0.0000 0 0.0000
Wedge Right 1 0.0000 1.850 0.000 0.0000 0 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.0000 1.850 0.000 0.000 0 0.000
Wedge Right 1 0.0000 1.850 0.000 0.000 0 0.000
5a. Top Fl plate 1 1 0.0000 1.800 0.000 0.000 0 0.000
5b. Top Fl plate 2 1 0.0150 1.788 0.027 0.048 7.81E‐07 0.048
6. Web Plate 1 0.0245 0.900 0.022 0.020 0.006 0.026
7b. Bott Fl plate 2 1 0.0000 0.0000 0.000 0 0 0
7C. TOP Fl holes 1 ‐0.0039 1.7875 ‐0.007 ‐0.01246 ‐2E‐07 ‐0.01246
Girder Alone Σ 0.0467 0.0420 0.0553 0.0063 0.0616
2

Girder Alone Σ 0.0545 0.0491 0.0678 0.0063 0.0740
2
Page 14 of 156

1. Deck slb (T Load) 1 0.033 ‐0.153 ‐0.005 0.001 0.0043 0.0051
2. Deck slab (P Load) 1 0.017 ‐0.153 ‐0.003 0.000 0.0022 0.0026
3. Deck Wdg (T)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
5a. Top Fl plate 1 1 0.000 0 0.000 0 0.0000 0.0000
5b. Top Fl plate 2 1 0.015 0 0.000 0 0.0005 0.0005
6. Web Plate 1 0.025 0 0.000 0 4E‐07 0.0000
7a. Bott Fl plate 1 1 0.015 0 0.000 0 0.000 0.0005
7b. Bott Fl plate 2 1 0.000 0 0.000 0 0.000 0.0000
Girder Alone Σ 0.055 0.000 0 0.001 0.001

Area ΣA 0.0467 0.085 0.066 0.0545 0.093 0.074
2 2
Mom of Inertia 0.024 0.046 0.038 0.030 0.054 0.045
2 2
Mom of Inertia 0.001 0.006 0.004 0.001 0.006 0.004
Yt ‐ 0.685 0.850 ‐ 0.724 0.882
Yi 0.900 0.435 0.600 0.900 0.474 0.632
Yb 0.900 1.365 1.200 0.900 1.326 1.168
Zt ‐ 0.068 0.045 ‐ 0.075 0.051
Zi 0.026 0.107 0.064 0.033 0.114 0.071
Zb 0.026 0.034 0.032 0.033 0.041 0.039
Page 15 of 156
OUTER GIRDER ‐SECTION AT L/4 OF 40M SPAN (I.E. 34.4 M FROM END SUPPORT)
200 200 deck slab 1493 200
Wedge Left
Wedge Right
1800 14 top plate 1
top plate 2 600 25
Bottom plate 2
Web plate 14 1750

1. Deck slb (T Load) 1 0.0398 1.950 0.078 0.151 0.000 0.152
2. Deck slab (P Load) 1 0.0199 1.950 0.039 0.076 0.000 0.076
3. Deck Wdg (T)
Wedge Left 1 0.0000 1.850 0.000 0.0000 0 0.0000
Wedge Right 1 0.0000 1.850 0.000 0.0000 0 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.0000 1.850 0.000 0.000 0 0.000
Wedge Right 1 0.0000 1.850 0.000 0.000 0 0.000
5a. Top Fl plate 1 1 0.0000 1.800 0.000 0.000 0 0.000
5b. Top Fl plate 2 1 0.0150 1.788 0.027 0.048 7.81E‐07 0.048
6. Web Plate 1 0.0245 0.900 0.022 0.020 0.006 0.026
7b. Bott Fl plate 2 1 0.0000 0.0000 0.000 0 0 0
7C. TOP Fl holes 1 ‐0.0039 1.7875 ‐0.007 ‐0.01246 ‐2E‐07 ‐0.01246
Girder Alone Σ 0.0467 0.0420 0.0553 0.0063 0.0616
Girder Alone Σ 0.0545 0.0491 0.0678 0.0063 0.0740
Page 16 of 156

1. Deck slb (T Load) 1 0.040 ‐0.183 ‐0.007 0.001 0.0074 0.0087
2. Deck slab (P Load) 1 0.020 ‐0.183 ‐0.004 0.001 0.0037 0.0044
3. Deck Wdg (T)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
5a. Top Fl plate 1 1 0.000 0 0.000 0 0.0000 0.0000
5b. Top Fl plate 2 1 0.015 0 0.000 0 0.0005 0.0005
6. Web Plate 1 0.025 0 0.000 0 4E‐07 0.0000
7a. Bott Fl plate 1 1 0.015 0 0.000 0 0.000 0.0005
7b. Bott Fl plate 2 1 0.000 0 0.000 0 0.000 0.0000
Girder Alone Σ 0.055 0.000 0 0.001 0.001

Area ΣA 0.0467 0.092 0.069 0.0545 0.100 0.077
2 2
Mom of Inertia 0.024 0.049 0.040 0.030 0.057 0.047
2 2
Mom of Inertia 0.001 0.010 0.005 0.001 0.010 0.005
Yt ‐ 0.641 0.813 ‐ 0.681 0.847
Yi 0.900 0.391 0.563 0.900 0.431 0.597
Yb 0.900 1.409 1.237 0.900 1.369 1.203
Zt ‐ 0.076 0.049 ‐ 0.083 0.056
Zi 0.026 0.124 0.071 0.033 0.131 0.079
Zb 0.026 0.034 0.032 0.033 0.041 0.039
Page 17 of 156
OUTER GIRDER ‐SECTION AT 3L/8 OF 40 M SPAN (I.E. 39.4 M FROM END SUPPORT)
200 200 deck slab 1600 200
Wedge Left
Wedge Right
1800 14 top plate 1
top plate 2 600 25
Bottom plate 2
Web plate 14 1750
1. Deck slb (T Load) 1 0.0427 1.950 0.083 0.162 0.000 0.162
2. Deck slab (P Load) 1 0.0213 1.950 0.042 0.081 0.000 0.081
3. Deck Wdg (T)
Wedge Left 1 0.0000 1.850 0.000 0.0000 0 0.0000
Wedge Right 1 0.0000 1.850 0.000 0.0000 0 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.0000 1.850 0.000 0.000 0 0.000
Wedge Right 1 0.0000 1.850 0.000 0.000 0 0.000
5a. Top Fl plate 1 1 0.0000 1.800 0.000 0.000 0 0.000
5b. Top Fl plate 2 1 0.0150 1.788 0.027 0.048 7.81E‐07 0.048
6. Web Plate 1 0.0245 0.900 0.022 0.020 0.006 0.026
7b. Bott Fl plate 2 1 0.0000 0.0000 0.000 0 0 0
7C. TOP Fl holes 1 ‐0.0039 1.7875 ‐0.007 ‐0.01246 ‐2E‐07 ‐0.01246
Girder Alone Σ 0.0467 0.0420 0.0553 0.0063 0.0616
2

Girder Alone Σ 0.0545 0.0491 0.0678 0.0063 0.0740
2
Page 18 of 156

1. Deck slb (T Load) 1 0.043 ‐0.196 ‐0.008 0.002 0.0091 0.0107
2. Deck slab (P Load) 1 0.021 ‐0.196 ‐0.004 0.001 0.0045 0.0054
3. Deck Wdg (T)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
5a. Top Fl plate 1 1 0.000 0 0.000 0 0.0000 0.0000
5b. Top Fl plate 2 1 0.015 0 0.000 0 0.0005 0.0005
6. Web Plate 1 0.025 0 0.000 0 4E‐07 0.0000
7a. Bott Fl plate 1 1 0.015 0 0.000 0 0.000 0.0005
7b. Bott Fl plate 2 1 0.000 0 0.000 0 0.000 0.0000
Girder Alone Σ 0.055 0.000 0 0.001 0.001

Area ΣA 0.0467 0.095 0.071 0.0545 0.103 0.079
2 2
Mom of Inertia 0.024 0.049 0.041 0.030 0.058 0.048
2 2
Mom of Inertia 0.001 0.012 0.006 0.001 0.012 0.006
Yt ‐ 0.624 0.797 ‐ 0.664 0.832
Yi 0.900 0.374 0.547 0.900 0.414 0.582
Yb 0.900 1.426 1.253 0.900 1.386 1.218
Zt ‐ 0.079 0.051 ‐ 0.087 0.058
Zi 0.026 0.132 0.075 0.033 0.139 0.082
Zb 0.026 0.035 0.033 0.033 0.042 0.039
Page 19 of 156
OUTER GIRDER ‐SECTION AT L/2 OF 40 M SPAN (I.E. 44.4 M FROM END SUPPORT)
200 200 deck slab 1706 200
Wedge Left
Wedge Right
1800 14 top plate 1
top plate 2 600 25
Bottom plate 2
Web plate 14 1750

1. Deck slb (T Load) 1 0.0455 1.950 0.089 0.173 0.000 0.173
2. Deck slab (P Load) 1 0.0228 1.950 0.044 0.087 0.000 0.087
3. Deck Wdg (T)
Wedge Left 1 0.0000 1.850 0.000 0.0000 0 0.0000
Wedge Right 1 0.0000 1.850 0.000 0.0000 0 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.0000 1.850 0.000 0.000 0 0.000
Wedge Right 1 0.0000 1.850 0.000 0.000 0 0.000
5a. Top Fl plate 1 1 0.0000 1.800 0.000 0.000 0 0.000
5b. Top Fl plate 2 1 0.0150 1.788 0.027 0.048 7.81E‐07 0.048
6. Web Plate 1 0.0245 0.900 0.022 0.020 0.006 0.026
7b. Bott Fl plate 2 1 0.0000 0.0000 0.000 0 0 0
7C. TOP Fl holes 1 ‐0.0039 1.7875 ‐0.007 ‐0.01246 ‐2E‐07 ‐0.01246
Girder Alone Σ 0.0467 0.0420 0.0553 0.0063 0.0616
Girder Alone Σ 0.0545 0.0491 0.0678 0.0063 0.0740
Page 20 of 156

1. Deck slb (T Load) 1 0.046 ‐0.209 ‐0.009 0.002 0.0110 0.0130
2. Deck slab (P Load) 1 0.023 ‐0.209 ‐0.005 0.001 0.0055 0.0065
3. Deck Wdg (T)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
5a. Top Fl plate 1 1 0.000 0 0.000 0 0.0000 0.0000
5b. Top Fl plate 2 1 0.015 0 0.000 0 0.0005 0.0005
6. Web Plate 1 0.025 0 0.000 0 4E‐07 0.0000
7a. Bott Fl plate 1 1 0.015 0 0.000 0 0.000 0.0005
7b. Bott Fl plate 2 1 0.000 0 0.000 0 0.000 0.0000
Girder Alone Σ 0.055 0.000 0 0.001 0.001

Area ΣA 0.0467 0.098 0.072 0.0545 0.106 0.080
2 2
Mom of Inertia 0.024 0.050 0.042 0.030 0.058 0.049
2 2
Mom of Inertia 0.001 0.014 0.008 0.001 0.014 0.008
Yt ‐ 0.607 0.782 ‐ 0.647 0.818
Yi 0.900 0.357 0.532 0.900 0.397 0.568
Yb 0.900 1.443 1.268 0.900 1.403 1.232
Zt ‐ 0.083 0.053 ‐ 0.090 0.060
Zi 0.026 0.141 0.078 0.033 0.147 0.086
Zb 0.026 0.035 0.033 0.033 0.042 0.040
Page 21 of 156
INNER GIRDER ‐END L/2 SPAN SECTION (0 TO 12.2M FROM END SUPPORT)
200 200 deck slab 1963 200
Wedge Left
480X50 Wedge Centre 480 50
Wedge Right
1800 14 top plate 1
top plate 2 600 25
Bottom plate 1 600 25
Bottom plate 2
Web plate 14 1750
b Total Depth 2050.0 mm
Calculation of Ixx
ψ = 1.000 ω = 0.500
1. Deck slb (T Load) 1 0.0523 1.950 0.102 0.199 0.000 0.199
2. Deck slab (P Load) 1 0.0262 1.950 0.051 0.100 0.000 0.100
3. Deck Wdg (T)
Wedge Left 1 0.0000 1.850 0.000 0.0000 0 0.0000
Wedge Right 1 0.0000 1.850 0.000 0.0000 0 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.0000 1.850 0.000 0.000 0 0.000
Wedge Right 1 0.0000 1.850 0.000 0.000 0 0.000
5a. Top Fl plate 1 1 0.0000 1.800 0.000 0.000 0 0.000
5b. Top Fl plate 2 1 0.0150 1.788 0.027 0.048 7.81E‐07 0.048
6. Web Plate 1 0.0245 0.900 0.022 0.020 0.006 0.026
7b. Bott Fl plate 2 1 0.0000 0.0000 0 0 0 0
7C. TOP Fl holes 1 ‐0.0039 1.788 ‐0.007 ‐0.01246 ‐2E‐07 ‐0.01246
Girder Alone Σ 0.0467 0.0420 0.0553 0.0063 0.0616
Girder Alone Σ 0.0545 0.0491 0.0678 0.0063 0.0740
Page 22 of 156

1. Deck slb (T Load) 1 0.052 0.000 0.000 0.000 0.0168 0.0168
2. Deck slab (P Load) 1 0.026 0.000 0.000 0.000 0.0084 0.0084
3. Deck Wdg (T)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Rect wedge at centre 1 0.0032 0.000 0.000 0 6.14E‐05 6.14E‐05
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
5a. Top Fl plate 1 1 0.000 0 0.000 0 0.0000 0.0000
5b. Top Fl plate 2 1 0.0150 0 0.000 0 0.0005 0.0005
6. Web Plate 1 0.0245 0 0.000 0 4E‐07 0.0000
7a. Bott Fl plate 1 1 0.0150 0 0.000 0 0.000 0.0005
7b. Bott Fl plate 2 1 0.000 0 0.000 0 0.000 0.0000
Girder Alone Σ 0.055 0.000 0 0.001 0.001

Area ΣA 0.0467 0.102 0.074 0.0545 0.110 0.082
2 2
Mom of Inertia 0.024 0.052 0.043 0.030 0.060 0.050
CG from web cntr 'z' Zw = ΣAz/ΣA 0.000 0.000 0.000 0.000 0.000 0.000
2 2
Mom of Inertia 0.001 0.018 0.009 0.001 0.018 0.009
Yt ‐ 0.583 0.761 ‐ 0.624 0.798
Yi 0.900 0.333 0.511 0.900 0.374 0.548
Yb 0.900 1.467 1.289 0.900 1.426 1.252
Zt ‐ 0.088 0.056 ‐ 0.096 0.063
Zi 0.026 0.155 0.084 0.033 0.161 0.091
Zb 0.026 0.035 0.033 0.033 0.042 0.040
Page 23 of 156
INNER GIRDER ‐SECTION AT 5L/8 (I.E. 15.25M FROM END SUPPORT)
200 200 deck slab 1774 200
Wedge Left
Wedge Right
1800 14 top plate 1
top plate 2 600 25
Bottom plate 2
Web plate 14 1750
Total Depth 2050 mm
1. Deck slb (T Load) 1 0.0473 1.950 0.092 0.180 0.000 0.180
2. Deck slab (P Load) 1 0.0237 1.950 0.046 0.090 0.000 0.090
3. Deck Wdg (T)
Wedge Left 1 0.0000 1.850 0.000 0.0000 0 0.0000
Wedge Right 1 0.0000 1.850 0.000 0.0000 0 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.0000 1.850 0.000 0.000 0 0.000
Wedge Right 1 0.0000 1.850 0.000 0.000 0 0.000
5a. Top Fl plate 1 1 0.0000 1.800 0.000 0.000 0 0.000
5b. Top Fl plate 2 1 0.0150 1.788 0.027 0.048 7.81E‐07 0.048
6. Web Plate 1 0.0245 0.900 0.022 0.020 0.006 0.026
7b. Bott Fl plate 2 1 0.0000 0.0000 0.000 0 0 0
7C. TOP Fl holes 1 ‐0.0039 1.7875 ‐0.007 ‐0.01246 ‐2E‐07 ‐0.01246
Girder Alone Σ 0.0467 0.0420 0.0553 0.0063 0.0616
2

Girder Alone Σ 0.0545 0.0491 0.0678 0.0063 0.0740
2
Page 24 of 156

1. Deck slb (T Load) 1 0.047 0.000 0.000 0.000 0.0124 0.0124
2. Deck slab (P Load) 1 0.024 0.000 0.000 0.000 0.0062 0.0062
3. Deck Wdg (T)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
5a. Top Fl plate 1 1 0.000 0 0.000 0 0.0000 0.0000
5b. Top Fl plate 2 1 0.015 0 0.000 0 0.0005 0.0005
6. Web Plate 1 0.025 0 0.000 0 4E‐07 0.0000
7a. Bott Fl plate 1 1 0.015 0 0.000 0 0.000 0.0005
7b. Bott Fl plate 2 1 0.000 0 0.000 0 0.000 0.0000
Girder Alone Σ 0.055 0.000 0 0.001 0.001

Area ΣA 0.0467 0.097 0.072 0.0545 0.105 0.080
2 2
Mom of Inertia 0.024 0.050 0.042 0.030 0.059 0.049
2 2
Mom of Inertia 0.001 0.013 0.007 0.001 0.013 0.007
Yt ‐ 0.609 0.784 ‐ 0.649 0.820
Yi 0.900 0.359 0.534 0.900 0.399 0.570
Yb 0.900 1.441 1.266 0.900 1.401 1.230
Zt ‐ 0.083 0.053 ‐ 0.090 0.059
Zi 0.026 0.140 0.078 0.033 0.147 0.085
Zb 0.026 0.035 0.033 0.033 0.042 0.040
Page 25 of 156
200 200 deck slab 1586 200
Wedge Left
Wedge Right
1800 14 top plate 1
top plate 2 600 25
Bottom plate 2
Web plate 14 1750
1. Deck slb (T Load) 1 0.0423 1.950 0.082 0.161 0.000 0.161
2. Deck slab (P Load) 1 0.0211 1.950 0.041 0.080 0.000 0.080
3. Deck Wdg (T)
Wedge Left 1 0.0000 1.850 0.000 0.0000 0 0.0000
Wedge Right 1 0.0000 1.850 0.000 0.0000 0 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.0000 1.850 0.000 0.000 0 0.000
Wedge Right 1 0.0000 1.850 0.000 0.000 0 0.000
5a. Top Fl plate 1 1 0.0000 1.800 0.000 0.000 0 0.000
5b. Top Fl plate 2 1 0.0150 1.788 0.027 0.048 7.81E‐07 0.048
6. Web Plate 1 0.0245 0.900 0.022 0.020 0.006 0.026
7b. Bott Fl plate 2 1 0.0000 0.0000 0.000 0 0 0
7C. TOP Fl holes 1 ‐0.0039 1.7875 ‐0.007 ‐0.01246 ‐2E‐07 ‐0.01246
Girder Alone Σ 0.0467 0.0420 0.0553 0.0063 0.0616
2

Girder Alone Σ 0.0545 0.0491 0.0678 0.0063 0.0740
2
Page 26 of 156

1. Deck slb (T Load) 1 0.042 0.000 0.000 0.000 0.0089 0.0089
2. Deck slab (P Load) 1 0.021 0.000 0.000 0.000 0.0044 0.0044
3. Deck Wdg (T)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
5a. Top Fl plate 1 1 0.000 0 0.000 0 0.0000 0.0000
5b. Top Fl plate 2 1 0.015 0 0.000 0 0.0005 0.0005
6. Web Plate 1 0.025 0 0.000 0 4E‐07 0.0000
7a. Bott Fl plate 1 1 0.015 0 0.000 0 0.000 0.0005
7b. Bott Fl plate 2 1 0.000 0 0.000 0 0.000 0.0000
Girder Alone Σ 0.055 0.000 0 0.001 0.001

Area ΣA 0.0467 0.092 0.069 0.0545 0.100 0.077
2 2
Mom of Inertia 0.024 0.049 0.040 0.030 0.057 0.047
2 2
Mom of Inertia 0.001 0.010 0.005 0.001 0.010 0.005
Yt ‐ 0.636 0.809 ‐ 0.676 0.843
Yi 0.900 0.386 0.559 0.900 0.426 0.593
Yb 0.900 1.414 1.241 0.900 1.374 1.207
Zt ‐ 0.077 0.050 ‐ 0.084 0.056
Zi 0.026 0.127 0.072 0.033 0.134 0.080
Zb 0.026 0.035 0.033 0.033 0.041 0.039
Page 27 of 156
200 200 deck slab 1283 200
Wedge Left
Wedge Right
1800 14 top plate 1
top plate 2 600 25
Bottom plate 2
Web plate 14 1750
1. Deck slb (T Load) 1 0.0342 1.950 0.067 0.130 0.000 0.130
2. Deck slab (P Load) 1 0.0171 1.950 0.033 0.065 0.000 0.065
3. Deck Wdg (T)
Wedge Left 1 0.0000 1.850 0.000 0.0000 0 0.0000
Wedge Right 1 0.0000 1.850 0.000 0.0000 0 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.0000 1.850 0.000 0.000 0 0.000
Wedge Right 1 0.0000 1.850 0.000 0.000 0 0.000
5a. Top Fl plate 1 1 0.0000 1.800 0.000 0.000 0 0.000
5b. Top Fl plate 2 1 0.0150 1.788 0.027 0.048 7.81E‐07 0.048
6. Web Plate 1 0.0245 0.900 0.022 0.020 0.006 0.026
7b. Bott Fl plate 2 1 0.0000 0.0000 0.000 0 0 0
7C. TOP Fl holes 1 ‐0.0039 1.7875 ‐0.007 ‐0.01246 ‐2E‐07 ‐0.01246
Girder Alone Σ 0.0467 0.0420 0.0553 0.0063 0.0616
2

Girder Alone Σ 0.0545 0.0491 0.0678 0.0063 0.0740
2
Page 28 of 156

1. Deck slb (T Load) 1 0.034 0.000 0.000 0.000 0.0047 0.0047
2. Deck slab (P Load) 1 0.017 0.000 0.000 0.000 0.0023 0.0023
3. Deck Wdg (T)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
5a. Top Fl plate 1 1 0.000 0 0.000 0 0.0000 0.0000
5b. Top Fl plate 2 1 0.015 0 0.000 0 0.0005 0.0005
6. Web Plate 1 0.025 0 0.000 0 4E‐07 0.0000
7a. Bott Fl plate 1 1 0.015 0 0.000 0 0.000 0.0005
7b. Bott Fl plate 2 1 0.000 0 0.000 0 0.000 0.0000
Girder Alone Σ 0.055 0.000 0 0.001 0.001

Area ΣA 0.0467 0.084 0.065 0.0545 0.092 0.073
2 2
Mom of Inertia 0.024 0.046 0.038 0.030 0.054 0.045
2 2
Mom of Inertia 0.001 0.006 0.003 0.001 0.006 0.003
Yt ‐ 0.688 0.853 ‐ 0.727 0.884
Yi 0.900 0.438 0.603 0.900 0.477 0.634
Yb 0.900 1.362 1.197 0.900 1.323 1.166
Zt ‐ 0.067 0.045 ‐ 0.074 0.051
Zi 0.026 0.106 0.063 0.033 0.113 0.071
Zb 0.026 0.034 0.032 0.033 0.041 0.039
Page 29 of 156
INNER GIRDER ‐SECTION AT CONT SUPPORT (I.E. 24.4 M FROM END SUPPORT)
200 200 deck slab 1254 200
Wedge Left
Wedge Right
1800 14 top plate 1
top plate 2 600 25
Bottom plate 2
Web plate 14 1750
Total Depth 2050 mm
1. Deck slb (T Load) 1 0.0334 1.950 0.065 0.127 0.000 0.127
2. Deck slab (P Load) 1 0.0167 1.950 0.033 0.064 0.000 0.064
3. Deck Wdg (T)
Wedge Left 1 0.0000 1.850 0.000 0.0000 0 0.0000
Wedge Right 1 0.0000 1.850 0.000 0.0000 0 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.0000 1.850 0.000 0.000 0 0.000
Wedge Right 1 0.0000 1.850 0.000 0.000 0 0.000
5a. Top Fl plate 1 1 0.0000 1.800 0.000 0.000 0 0.000
5b. Top Fl plate 2 1 0.0150 1.788 0.027 0.048 7.81E‐07 0.048
6. Web Plate 1 0.0245 0.900 0.022 0.020 0.006 0.026
7b. Bott Fl plate 2 1 0.0000 0.0000 0.000 0 0 0
7C. TOP Fl holes 1 ‐0.0039 1.7875 ‐0.007 ‐0.01246 ‐2E‐07 ‐0.01246
Girder Alone Σ 0.0467 0.0420 0.0553 0.0063 0.0616
2

Girder Alone Σ 0.0545 0.0491 0.0678 0.0063 0.0740
2
Page 30 of 156

1. Deck slb (T Load) 1 0.033 0.000 0.000 0.000 0.0044 0.0044
2. Deck slab (P Load) 1 0.017 0.000 0.000 0.000 0.0022 0.0022
3. Deck Wdg (T)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
5a. Top Fl plate 1 1 0.000 0 0.000 0 0.0000 0.0000
5b. Top Fl plate 2 1 0.015 0 0.000 0 0.0005 0.0005
6. Web Plate 1 0.025 0 0.000 0 4E‐07 0.0000
7a. Bott Fl plate 1 1 0.015 0 0.000 0 0.000 0.0005
7b. Bott Fl plate 2 1 0.000 0 0.000 0 0.000 0.0000
Girder Alone Σ 0.055 0.000 0 0.001 0.001

Area ΣA 0.0467 0.083 0.065 0.0545 0.091 0.073
2 2
Mom of Inertia 0.024 0.046 0.038 0.030 0.054 0.045
2 2
Mom of Inertia 0.001 0.005 0.003 0.001 0.005 0.003
Yt ‐ 0.693 0.857 ‐ 0.732 0.889
Yi 0.900 0.443 0.607 0.900 0.482 0.639
Yb 0.900 1.357 1.193 0.900 1.318 1.161
Zt ‐ 0.066 0.044 ‐ 0.073 0.050
Zi 0.026 0.104 0.063 0.033 0.111 0.070
Zb 0.026 0.034 0.032 0.033 0.041 0.039
Page 31 of 156
INNER GIRDER ‐SECTION AT L/8 OF 40M SPAN (I.E. 29.4M FROM END SUPPORT)
200 200 deck slab 1556 200
Wedge Left
Wedge Right
1800 14 top plate 1
top plate 2 600 25
Bottom plate 2
Web plate 14 1750
1. Deck slb (T Load) 1 0.0415 1.950 0.081 0.158 0.000 0.158
2. Deck slab (P Load) 1 0.0207 1.950 0.040 0.079 0.000 0.079
3. Deck Wdg (T)
Wedge Left 1 0.0000 1.850 0.000 0.0000 0 0.0000
Wedge Right 1 0.0000 1.850 0.000 0.0000 0 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.0000 1.850 0.000 0.000 0 0.000
Wedge Right 1 0.0000 1.850 0.000 0.000 0 0.000
5a. Top Fl plate 1 1 0.0000 1.800 0.000 0.000 0 0.000
5b. Top Fl plate 2 1 0.0150 1.788 0.027 0.048 7.81E‐07 0.048
6. Web Plate 1 0.0245 0.900 0.022 0.020 0.006 0.026
7b. Bott Fl plate 2 1 0.0000 0.0000 0.000 0 0 0
7C. TOP Fl holes 1 ‐0.0039 1.7875 ‐0.007 ‐0.01246 ‐2E‐07 ‐0.01246
Girder Alone Σ 0.0467 0.0420 0.0553 0.0063 0.0616
Girder Alone Σ 0.0545 0.0491 0.0678 0.0063 0.0740
2
Page 32 of 156

1. Deck slb (T Load) 1 0.041 0.000 0.000 0.000 0.0084 0.0084
2. Deck slab (P Load) 1 0.021 0.000 0.000 0.000 0.0042 0.0042
3. Deck Wdg (T)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
5a. Top Fl plate 1 1 0.000 0 0.000 0 0.0000 0.0000
5b. Top Fl plate 2 1 0.015 0 0.000 0 0.0005 0.0005
6. Web Plate 1 0.025 0 0.000 0 4E‐07 0.0000
7a. Bott Fl plate 1 1 0.015 0 0.000 0 0.000 0.0005
7b. Bott Fl plate 2 1 0.000 0 0.000 0 0.000 0.0000
Girder Alone Σ 0.055 0.000 0 0.001 0.001

Area ΣA 0.0467 0.091 0.069 0.0545 0.099 0.077
2 2
Mom of Inertia 0.024 0.049 0.040 0.030 0.057 0.047
2 2
Mom of Inertia 0.001 0.009 0.005 0.001 0.009 0.005
Yt ‐ 0.641 0.813 ‐ 0.681 0.847
Yi 0.900 0.391 0.563 0.900 0.431 0.597
Yb 0.900 1.409 1.237 0.900 1.369 1.203
Zt ‐ 0.076 0.049 ‐ 0.083 0.056
Zi 0.026 0.125 0.071 0.033 0.132 0.079
Zb 0.026 0.035 0.033 0.033 0.041 0.039
Page 33 of 156
INNER GIRDER ‐SECTION AT L/4 OF 40M SPAN (I.E. 34.4 M FROM END SUPPORT)
200 200 deck slab 1858 200
Wedge Left
Wedge Right
1800 14 top plate 1
top plate 2 600 25
Bottom plate 2
Web plate 14 1750
1. Deck slb (T Load) 1 0.0496 1.950 0.097 0.188 0.000 0.189
2. Deck slab (P Load) 1 0.0248 1.950 0.048 0.094 0.000 0.094
3. Deck Wdg (T)
Wedge Left 1 0.0000 1.850 0.000 0.0000 0 0.0000
Wedge Right 1 0.0000 1.850 0.000 0.0000 0 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.0000 1.850 0.000 0.000 0 0.000
Wedge Right 1 0.0000 1.850 0.000 0.000 0 0.000
5a. Top Fl plate 1 1 0.0000 1.800 0.000 0.000 0 0.000
5b. Top Fl plate 2 1 0.0150 1.788 0.027 0.048 7.81E‐07 0.048
6. Web Plate 1 0.0245 0.900 0.022 0.020 0.006 0.026
7b. Bott Fl plate 2 1 0.0000 0.0000 0.000 0 0 0
7C. TOP Fl holes 1 ‐0.0039 1.7875 ‐0.007 ‐0.01246 ‐2E‐07 ‐0.01246
Girder Alone Σ 0.0467 0.0420 0.0553 0.0063 0.0616
2

Girder Alone Σ 0.0545 0.0491 0.0678 0.0063 0.0740
2
Page 34 of 156

1. Deck slb (T Load) 1 0.050 0.000 0.000 0.000 0.0143 0.0143
2. Deck slab (P Load) 1 0.025 0.000 0.000 0.000 0.0071 0.0071
3. Deck Wdg (T)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
5a. Top Fl plate 1 1 0.000 0 0.000 0 0.0000 0.0000
5b. Top Fl plate 2 1 0.015 0 0.000 0 0.0005 0.0005
6. Web Plate 1 0.025 0 0.000 0 4E‐07 0.0000
7a. Bott Fl plate 1 1 0.015 0 0.000 0 0.000 0.0005
7b. Bott Fl plate 2 1 0.000 0 0.000 0 0.000 0.0000
Girder Alone Σ 0.055 0.000 0 0.001 0.001

Area ΣA 0.0467 0.099 0.073 0.0545 0.107 0.081
2 2
Mom of Inertia 0.024 0.051 0.042 0.030 0.059 0.049
2 2
Mom of Inertia 0.001 0.015 0.008 0.001 0.015 0.008
Yt ‐ 0.597 0.774 ‐ 0.637 0.810
Yi 0.900 0.347 0.524 0.900 0.387 0.560
Yb 0.900 1.453 1.276 0.900 1.413 1.240
Zt ‐ 0.085 0.054 ‐ 0.093 0.061
Zi 0.026 0.147 0.081 0.033 0.153 0.088
Zb 0.026 0.035 0.033 0.033 0.042 0.040
Page 35 of 156
INNER GIRDER ‐SECTION AT 3L/8 OF 40 M SPAN (I.E. 39.4 M FROM END SUPPORT)
200 200 deck slab 1991 200
Wedge Left
Wedge Right
1800 14 top plate 1
top plate 2 600 25
Bottom plate 2
Web plate 14 1750
1. Deck slb (T Load) 1 0.0531 1.950 0.104 0.202 0.000 0.202
2. Deck slab (P Load) 1 0.0265 1.950 0.052 0.101 0.000 0.101
3. Deck Wdg (T)
Wedge Left 1 0.0000 1.850 0.000 0.0000 0 0.0000
Wedge Right 1 0.0000 1.850 0.000 0.0000 0 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.0000 1.850 0.000 0.000 0 0.000
Wedge Right 1 0.0000 1.850 0.000 0.000 0 0.000
5a. Top Fl plate 1 1 0.0000 1.800 0.000 0.000 0 0.000
5b. Top Fl plate 2 1 0.0150 1.788 0.027 0.048 7.81E‐07 0.048
6. Web Plate 1 0.0245 0.900 0.022 0.020 0.006 0.026
7b. Bott Fl plate 2 1 0.0000 0.0000 0.000 0 0 0
7C. TOP Fl holes 1 ‐0.0039 1.7875 ‐0.007 ‐0.01246 ‐2E‐07 ‐0.01246
Girder Alone Σ 0.0467 0.0420 0.0553 0.0063 0.0616
2

Girder Alone Σ 0.0545 0.0491 0.0678 0.0063 0.0740
2
Page 36 of 156

1. Deck slb (T Load) 1 0.053 0.000 0.000 0.000 0.0175 0.0175
2. Deck slab (P Load) 1 0.027 0.000 0.000 0.000 0.0088 0.0088
3. Deck Wdg (T)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
5a. Top Fl plate 1 1 0.000 0 0.000 0 0.0000 0.0000
5b. Top Fl plate 2 1 0.015 0 0.000 0 0.0005 0.0005
6. Web Plate 1 0.025 0 0.000 0 4E‐07 0.0000
7a. Bott Fl plate 1 1 0.015 0 0.000 0 0.000 0.0005
7b. Bott Fl plate 2 1 0.000 0 0.000 0 0.000 0.0000
Girder Alone Σ 0.055 0.000 0 0.001 0.001

Area ΣA 0.0467 0.103 0.075 0.0545 0.111 0.083
2 2
Mom of Inertia 0.024 0.052 0.043 0.030 0.060 0.050
2 2
Mom of Inertia 0.001 0.018 0.010 0.001 0.018 0.010
Yt ‐ 0.580 0.758 ‐ 0.620 0.795
Yi 0.900 0.330 0.508 0.900 0.370 0.545
Yb 0.900 1.470 1.292 0.900 1.430 1.255
Zt ‐ 0.089 0.057 ‐ 0.097 0.063
Zi 0.026 0.157 0.085 0.033 0.163 0.092
Zb 0.026 0.035 0.033 0.033 0.042 0.040
Page 37 of 156
INNER GIRDER ‐SECTION AT L/2 OF 40 M SPAN (I.E. 44.4 M FROM END SUPPORT)
200 200 deck slab 2124 200
Wedge Left
Wedge Right
1800 14 top plate 1
top plate 2 600 25
Bottom plate 2
Web plate 14 1750
1. Deck slb (T Load) 1 0.0566 1.950 0.110 0.215 0.000 0.216
2. Deck slab (P Load) 1 0.0283 1.950 0.055 0.108 0.000 0.108
3. Deck Wdg (T)
Wedge Left 1 0.0000 1.850 0.000 0.0000 0 0.0000
Wedge Right 1 0.0000 1.850 0.000 0.0000 0 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.0000 1.850 0.000 0.000 0 0.000
Wedge Right 1 0.0000 1.850 0.000 0.000 0 0.000
5a. Top Fl plate 1 1 0.0000 1.800 0.000 0.000 0 0.000
5b. Top Fl plate 2 1 0.0150 1.788 0.027 0.048 7.81E‐07 0.048
6. Web Plate 1 0.0245 0.900 0.022 0.020 0.006 0.026
7b. Bott Fl plate 2 1 0.0000 0.0000 0.000 0 0 0
7C. TOP Fl holes 1 ‐0.0039 1.7875 ‐0.007 ‐0.01246 ‐2E‐07 ‐0.01246
Girder Alone Σ 0.0467 0.0420 0.0553 0.0063 0.0616
2

Girder Alone Σ 0.0545 0.0491 0.0678 0.0063 0.0740
2
Page 38 of 156

1. Deck slb (T Load) 1 0.057 0.000 0.000 0.000 0.0213 0.0213
2. Deck slab (P Load) 1 0.028 0.000 0.000 0.000 0.0106 0.0106
3. Deck Wdg (T)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
4. Deck Wdg (P)
Wedge Left 1 0.000 0.000 0.000 0.000 0.0000 0.0000
Wedge Right 1 0.000 0.000 0.000 0.000 0.0000 0.0000
5a. Top Fl plate 1 1 0.000 0 0.000 0 0.0000 0.0000
5b. Top Fl plate 2 1 0.015 0 0.000 0 0.0005 0.0005
6. Web Plate 1 0.025 0 0.000 0 4E‐07 0.0000
7a. Bott Fl plate 1 1 0.015 0 0.000 0 0.000 0.0005
7b. Bott Fl plate 2 1 0.000 0 0.000 0 0.000 0.0000
Girder Alone Σ 0.055 0.000 0 0.001 0.001

Area ΣA 0.0467 0.107 0.077 0.0545 0.114 0.084
2 2
Mom of Inertia 0.024 0.053 0.044 0.030 0.061 0.051
2 2
Mom of Inertia 0.001 0.022 0.012 0.001 0.022 0.012
Yt ‐ 0.564 0.743 ‐ 0.604 0.780
Yi 0.900 0.314 0.493 0.900 0.354 0.530
Yb 0.900 1.486 1.307 0.900 1.446 1.270
Zt ‐ 0.093 0.059 ‐ 0.101 0.065
Zi 0.026 0.167 0.089 0.033 0.173 0.096
Zb 0.026 0.035 0.033 0.033 0.042 0.040
Page 39 of 156
END CROSS GIRDER
280 280 L0= 2.240
200 Beff (span side) = (L0/8) 0.280 m
50 155 Beff (EJ side) = 0.280 m
250x50
Component b t
1500 12 deck slab 560 200
Wedge Left 155 50
Wedge Centre 250 50
b Wedge Right
top plate 350 12
Bottom plate 350 12
Web plate 12 1476
Total Depth 1750 mm
Calculation of Ixx
ψ = 1.0 ω = 0.5
1. Deck slb (T Load) 1 0.01 1.65 0.02 0.04 4.98E‐05 0.041
2. Deck slab (P Load) 1 0.01 1.65 0.01 0.02 2.49E‐05 0.020
3. Deck Wdg (T)
Wedge left 1 0.0010 1.525 0.00 0.00 7.18E‐08 0.002
Wedge right 1 0.00 1.550 0.00 0.00 0 0
4. Deck Wdg (P)
Wedge left 1 0.0005 1.525 0.00 0.00 3.59E‐08 0.001202
Wedge right 1 0.00 1.550 0.00 0.00 0 0
5. Top Flange plate 1 0.0042 1.49 0.01 0.01 5.04E‐08 0.009
6. Web Plate 1 0.0177 0.75 0.01 0.01 0.003 0.013
7. Bott Flange plate 1 0.0042 0.006 0.000 1.51E‐07 5.04E‐08 2.02E‐07
7a. Bott Fl holes 1 0.0000 0.0060 0.000 0 0 0
Girder Alone Σ 0.026 0.020 0.019 0.003 0.023

S No. No. A z Az Az2 I0 I0+Az
2
1. Deck slb (T Load) 1 0.0149 0.0000 0.0000 0.0000 0.0004 0.0004

2. Deck slab (P Load) 1 0.0075 0.0000 0.0000 0.0000 0.0002 0.0002
3. Deck Wdg (T)
Wedge left 1 0.001 0.203 0.000 4.24E‐05 2.07E‐06 4.44E‐05
Page 40 of 156
Wedge right 1 0.000 0.000 0.000 0 0 0
4. Deck Wdg (P)
Wedge left 1 0.001 0.203 0.000 2.12E‐05 1.03E‐06 2.22E‐05
Wedge right 1 0.000 0.000 0.000 0 0 0
5. Top Flange plate 1 0.004 0.000 0.000 0 4.29E‐05 4.29E‐05
6. Web Plate 1 0.018 0.000 0.000 0 2.13E‐07 2.13E‐07
7. Bott Flange plate 1 0.004 0.000 0.000 0 4.29E‐05 4.29E‐05
Comp Sect (T loading) Σ 0.044 0.000 4.24E‐05 0.0005 0.0005
Comp Sect (P loading) Σ 0.035 0.000 2.12E‐05 0.0003 0.0003
Girder Alone Σ 0.026 0.000 0 8.6E‐05 8.6E‐05
Section Properties
Item Girder Comp (T) Comp (P)
Area ΣA 0.026 0.044 0.035 m2
Dist of CG from bottom fibre 'y' Yb = ΣAy/ΣA 0.750 1.105 0.972 m
2 2
Mom of Inertia 0.008 0.016 0.013 m4
Dist of CG from web centre 'z' Zw = ΣAz/ΣA 0.000 0.005 0.003 m
Mom of Inertia Iy = Σ(I0+Az2)‐ΣAz2 0.000 0.001 0.000 m4
Torsional Constant 0.000 0.000 0.000 m4
Yt ‐ 0.645 0.778 m
Yi 0.750 0.395 0.528 m
Yb 0.750 1.105 0.972 m
Zt ‐ 0.025 0.017 m3
Zi 0.010 0.041 0.025 m3
Zb 0.010 0.015 0.013 m3
INTERM. X GIRDER
1120 1120 Beff = 2.240
200
Component b t
deck slab 2240 200
1500 Wedge Left 0 0
12 Wedge Centre 100
b Wedge Right 0 0
top plate 350 12
Bottom plate 350 12
Web plate 12 1476
Total Depth 1800 mm
Calculation of Ixx
ψ = 1.0 ω = 0.5
Page 41 of 156
S No. No. A y Ay Ay2 I0 I0+Ay
2
1. Deck slb (T Load) 1 0.0597 1.7000 0.1015 0.1726 0.0002 0.1728

2. Deck slab (P Load) 1 0.0299 1.7000 0.0508 0.0863 0.0001 0.0864
3. Deck Wdg (T)
Wedge left 1 0 1.6 0.0000 0 0 0
Rect wedge at centre 1 0 1.55 0.0000 0.0000 0 0.0000
Wedge right 1 0 1.6 0.0000 0 0 0
4. Deck Wdg (P)
Wedge left 1 0 1.6 0.0000 0 0 0
Rect wedge at centre 1 0.0000 1.55 0.0000 0.000 0 0.000
Wedge right 1 0 1.6 0.0000 0 0 0
5. Top Flange plate 1 0.0042 1.494 0.0063 0.009 5.04E‐08 0.009
6. Web Plate 1 0.0177 0.75 0.0133 0.010 0.003 0.013
7. Bott Flange plate 1 0.0042 0.006 0.0000 1.51E‐07 5.04E‐08 2.02E‐07
Girder Alone Σ 0.0261 0.020 0.019 0.003 0.023

1. Deck slb (T Load) 1 0.060 0 0.00 0 0.025 0.025
2. Deck slab (P Load) 1 0.030 0 0.00 0 0.012 0.012
3. Deck Wdg (T)
Triangle outside 1 0.000 0 0.00 0 0 0
Rect wedge at c/l 1 0.000 0 0.00 0 0 0
Rect wedge inner side 1 0.000 0 0.00 0 0 0
4. Deck Wdg (P)
Triangle outside 1 0.000 0 0.00 0 0 0
Rect wedge at c/l 1 0.000 0 0.00 0 0 0
Rect wedge inner side 1 0.000 0 0.00 0 0 0
5. Top Flange plate 1 0.004 0 0.00 0 4.29E‐05 4.29E‐05
6. Web Plate 1 0.018 0 0.00 0 2.13E‐07 2.13E‐07
7. Bott Flange plate 1 0.004 0 0.00 0 4.29E‐05 4.29E‐05
Comp Sect (T loading) Σ 0.086 0.00 0 0.025 0.025
Comp Sect (P loading) Σ 0.056 0.00 0 0.013 0.0126
Girder Alone Σ 0.026 0.00 0 8.6E‐05 8.6E‐05
Section Properties
Item Girder Comp (T) Comp (P)
Area ΣA 0.026 0.026 0.026 m2
Dist of CG from bottom fibre 'y' Yb = ΣAy/ΣA 0.750 0.750 0.750 m
Page 42 of 156
Mom of Inertia Ix = Σ(I0+Ay2)‐ΣAy2 0.008 0.008 0.008 m4
Dist of CG from web centre 'z' Zw = ΣAz/ΣA 0.000 0.000 0.000 m
2 2
Mom of Inertia 0.00009 0.000 0.000 m4
Torsional Constant 0.000 0.000 0.000 m4
Yt ‐ ‐ ‐ m
Yi 0.750 0.750 0.750 m
Yb 0.750 0.750 0.750 m
Zt ‐ ‐ ‐ m3
Zi 0.010 0.010 0.010 m3
Zb 0.010 0.010 0.010 m3
Effect of deck slab ignored.
CONCRETE ELEMENTS
MEM CROSS SECTION PROPERTY TRANS. PERM.
1.550 CROSS SECT AREA 0.041 0.021
End X girder
cantilever)
outside (in
0.200 Yb 0.100 0.100

Izz 0.0001 0.0001
Iyy 0.008 0.004
0.3 CROSS SECT AREA 0.008 0.004
along edge
Long mem
0.200 Yb 0.100 0.100

Ixx 0.00000 0.00000
Iyy 0.000 0.000
2.500 CROSS SECT AREA 0.067 0.034
Trans deck
members
0.200 Yb 0.100 0.100

Ixx 0.0002 0.0001
Iyy 0.035 0.017
Page 43 of 156
3 LOAD
3.1 SUPERIMPOSED DEAD LOAD
Wearing coat has been considered as 65 mm at present and 25 mm for future overlay.
Loading due to Crash Barrier 0.3 *25.0 7.5 kN/m
7.5 kN/m
Loading due to W/C 0.09 *22.0 1.98 kN/m2
say 2 kN/m2
2.225
1.425
G1 G2 G3 G4 G5 G6
0.8 2.24 2.24

(typ) 0.8
Load on Left edge member 7.5 kN/m

Load on Girder G1 (1.12+0.8‐0.45)*2 2.94 kN/m
Load on Girder G2, G3 & G4 2.24*2 4.48 kN/m
Load on Girder G5 (2.24‐0.45)*2+7.5*1.425/2.24 8.35 kN/m
Load on Girder G6 (1.12+0.8‐0.45)*2+7.5*(1‐1.425/2.24) 5.67 kN/m
Loading on right edge member 7.5 kN/m
3.2 LIVE LOAD

Five conditions of live load has been considered for live load analysis.
1 70 R (Wheeled vehicle moved along edge of the carriageway towards median side)
2 70 R (Wheeled vehicle moved along centre of the carriageway)
3 70 R (Wheeled vehicle moved along edge towards footpath side)
4 Class A two lane moved adjacent to crash barrier near median
5 Class A two lane moved along centre of bridge
70R W
Case 1
Page 44 of 156
70R W
Case 2
70R W
3.56 2.45
Case 3
CLASS A 2 LANE
Case 4
CLASS A 2 LANE FPLL
1.815 0.425
Case 5
Case 1
Distance of inner face of crash barrier from x axis (i.e. Z=0) 0.05 m
Lateral clearance between Crash Barrier and edge of outre most wheel 1.2 m
Half width of wheel 0.43 m
Distance of wheel nearer median ‐1.68 m
Distance of other wheel ‐3.61 m
Page 45 of 156
Case 2
Distance of wheel nearer median ‐2.24*5/2+1.93/2 ‐4.635 m
Case 3
Distance of wheel nearer median ‐11.375‐0.225+2.45+3.56 ‐5.59 m
Case 4
First wheel of first vehicle 0.05+0.4 0.45 m
Second wheel of first vehicle 2.25 m
First wheel of 2nd vehicle 0.45+1.8+1.7 3.95 m
Second wheel of 2nd vehicle 5.75 m
Case 5
First wheel of first vehicle ‐2.24*5/2+2.65 ‐2.95 m
Second wheel of first vehicle ‐4.75 m
First wheel of 2nd vehicle ‐2.95+1.8+1.7 ‐6.45 m
Second wheel of 2nd vehicle ‐8.25 m
FPLL (400‐260+4800/40)/100*1.5 KN/M 3.90 Kn/M

FPLL Rxn on G5 0.74 kN/m Rxn on G6 3.16 kN/m
Weight of Deck Slab
Outer Girder
L B density wt
200 thick 1.42 0.2 2.5 0.710 t/m
50 extra over flange 0.6 0.05 2.5 0.075 t/m
Cladding 2 0.005 7.85 0.079 t/m
0.864 t/m
Extra due to extended deck slab
deck slab 0.5 0.25 2.5 0.313 t/m
total udl 0.8635+0.313 1.176 t/m
say 1.200 t/m
Inner Girder
L B density wt
200 thick 2.24 0.2 2.5 1.120 t/m
50 extra over flange 0.6 0.05 2.5 0.075 t/m
1.195 say 1.25 t/m
4 TABULATION OF BENDING MOMENT AND SHEAR FORCE (UNIT kN.m & KN)
The BM & Shear F obtained from STAAD analysis for different loads are tabulated below.
The BM and shear Force due to self weight of steel girders are further increased by 25% to
account for the weight of splice plates, stiffners and bracings etc.
Page 46 of 156
4.1 SUMMARY FO BM FOR DL, SDL & LL
BM (OUTER GIRDER ‐ MEDIAN SIDE) BM (OUTER GIRDER ‐ FOOTPATH SIDE)

LL LL
SEC DL SIDL DL SIDL
SAGG HOGG SAGG HOGG
2 ‐223 ‐111 ‐348 128 ‐223 ‐139 ‐207 80
3 ‐421 ‐198 ‐778 294 ‐421 ‐254 ‐420 186
4 ‐508 ‐219 ‐1158 460 ‐508 ‐294 ‐616 292
5 ‐486 ‐176 ‐1476 624 ‐486 ‐261 ‐801 398
6 ‐340 ‐120 ‐1521 772 ‐340 ‐182 ‐845 494
7 ‐71 ‐40 ‐1381 911 ‐71 ‐58 ‐764 603
8 322 70 ‐1081 1036 322 115 ‐572 720
SPLICE 9 836 214 ‐608 1148 836 344 ‐289 840
10 1460 424 ‐228 1260 1460 646 ‐121 977
11 2194 698 ‐218 1294 2194 1022 ‐124 903
12 1316 385 ‐153 738 1316 584 ‐91 476
SPLICE 13 548 137 ‐294 562 548 220 ‐102 300
14 ‐110 ‐46 ‐797 551 ‐110 ‐72 ‐474 313
15 ‐647 ‐193 ‐1209 517 ‐647 ‐307 ‐802 307
16 ‐1061 ‐312 ‐1543 467 ‐1061 ‐494 ‐1038 284
SPLICE 17 ‐1351 ‐410 ‐1767 407 ‐1351 ‐640 ‐1142 249
18 ‐1515 ‐506 ‐1767 345 ‐1515 ‐750 ‐1110 208
19 ‐1570 ‐538 ‐1766 250 ‐1570 ‐786 ‐937 167
BM (INNER GIRDERS)
Dist from LL
SEC C/L Brg at DL SIDL
P143 SAGG HOGG
2 1.9 ‐227 ‐105 ‐594 102
3 4.4 ‐427 ‐195 ‐1079 236
4 6.9 ‐516 ‐231 ‐1304 369
5 9.4 ‐493 ‐212 ‐1271 501
6 11.9 ‐347 ‐149 ‐1282 627
7 14.4 ‐76 ‐37 ‐1170 746
8 16.9 319 126 ‐941 859
SPLICE 9 19.4 837 338 ‐710 970
10 21.9 1467 604 ‐225 1083
11 24.4 2210 925 ‐168 1129
12 26.9 1324 539 ‐122 653
SPLICE 13 29.4 550 208 ‐481 504
14 31.9 ‐112 ‐69 ‐741 436
15 34.4 ‐649 ‐296 ‐1041 389
16 36.9 ‐1063 ‐473 ‐1274 347
Page 47 of 156
SPLICE 17 39.4 ‐1353 ‐599 ‐1460 302
18 41.9 ‐1520 ‐680 ‐1778 254
19 44.4 ‐1576 ‐708 ‐1886 202
4.2 SUMMARY FO SHEAR FORCE FOR DL, SDL & LL
SHEAR
DEAD LOAD SIDL LIVE LOAD
SEC OG1 OG2 IG OG1 OG2 IG OG1 OG2 IG
2 101 101 103 37 50 48 181 88 307
3 57 57 58 11 21 26 171 81 203
4 13 13 13 -15 -9 11 152 80 99
5 ‐36 ‐36 ‐36 -20 -27 -15 80 ‐38 ‐80
6 ‐86 ‐86 ‐86 -29 -45 -34 ‐112 ‐35 124
7 ‐135 ‐135 ‐135 -41 -65 -53 ‐158 ‐79 ‐178
8 ‐184 ‐184 ‐185 -55 -87 -73 ‐215 ‐115 ‐200
SPLICE 9 ‐228 ‐228 ‐230 -81 -117 -94 ‐233 ‐116 ‐265
10 ‐272 ‐272 ‐275 -107 -146 -116 ‐240 ‐77 ‐348
11 373 373 376 128 180 167 268 185 404
12 329 329 332 102 150 145 265 179 325
SPLICE 13 285 285 287 76 121 123 255 174 259
14 237 237 237 62 98 103 227 147 260
15 187 187 188 50 79 83 200 113 217
16 138 138 138 42 63 63 158 75 216
SPLICE 17 88 88 89 41 48 45 107 45 277
18 44 44 45 15 19 23 93 38 204
19 0 0 0 10 10 0 ‐91 38 ‐80
4.3 DIFFERENTIAL SETTLEMENT EFFECTS

DESIGN BM DESIGN SH
Sec
OG(M) OG(F) IG OG(M) OG(F) IG
2 36 36 36 19 19 19
3 82 82 83 19 19 19
4 129 129 130 19 19 19
5 176 176 177 17 17 18
6 218 218 222 16 16 18
7 258 258 266 15 15 18
8 296 296 308 15 15 17
9 333 333 350 15 15 17
10 369 369 393 15 15 17
11 406 406 436 19 19 22
Page 48 of 156
12 360 360 383 19 19 22
13 314 314 329 19 19 22
14 267 267 277 19 19 22
15 220 220 224 20 20 22
16 170 170 170 21 21 22
17 148 147 153 23 23 23
18 148 148 153 23 23 23
19 148 148 153 23 23 23
4.4 EFFECT OF PRESTRESSING

DESIGN BM AXIAL FORCE
Sec
OG(M) OG(F) IG OG(M) OG(F) IG
2 32 32 15 -24 -24 20
3 74 74 35 -57 -57 42
4 118 118 53 -95 -95 58
5 162 162 71 -27 -27 59
6 160 160 64 53 53 59
7 115 115 26 132 132 60
8 21 21 -66 199 199 61
9 -137 -137 -125 175 175 94
10 -294 -294 -211 159 160 104
11 -450 -450 -297 159 160 104
12 -281 -281 -187 172 172 95
13 -111 -111 -78 192 193 65
14 59 59 30 126 126 65
15 165 165 119 46 46 64
16 225 225 181 -34 -34 64
17 250 250 212 -102 -102 64
18 246 246 214 -87 -86 67
19 245 245 215 -87 -86 67
Page 49 of 156
5 CALCULATION OF STRESSES DUE TO TEMPERATURE GRADIENT
5.1 OUTER GIRDER (Median Side)
at span
Total depth of section h 2.050 m
Total depth of web h' 1.7500 m
CG from Bottom Y 1.4027 m
MOI of section I 0.0585 m4
Area of Section A 0.1059 m2
Modulus of elasticity of steel Es 2.00E+08 kN/m2
Modulus of elasticity of concrete Ec 3.50E+07 kN/m2
Coeff of thermal expansion a 1.20E‐05 /0C
Section modulus at Top Zt 0.0904 m3
Section modulus at bottom Zb 0.0417 m3
TEMPERATURE RISE CASE
T1= 20.50 0C Temp at slab bottom 3.14
T2= 4.00 0C
T1 0.241 0.167
0.165 0.275 0.275
0.510 T2
1.750 1.750
0.025 0.025
0.600 0.600
span section support section
STRESS AT SPAN SECTION
dist from top height E.α.ΔT b Force y from top e Moment
S No.
m m kN/sqm m kN m m kNm
1 0.000 49200
2 0.165 0.17 9600 0.241 1171 0.064 0.58 683
3 0.275 0.11 7529 0.241 227 0.218 0.43 98
4 0.675 0.40 0 0.014 21 0.408 0.24 5
5 2.050
1420 786
The moment diagram due to continuity, when 714 kNM BM is released, is drawn below.
R=37.80
M=786
M=136
Page 50 of 156
Section 2 3 4 5 6 7 8 9 10 11
Di from end 1.9 4.4 6.9 9.4 11.9 14.4 16.9 19.4 21.9 24.4
Moment 714 620 525 431 336 242 147 53 ‐42 ‐136
A 0.102 0.102 0.102 0.102 0.102 0.098 0.093 0.086 0.086 0.086
Zt 0.086 0.086 0.086 0.086 0.086 0.081 0.075 0.067 0.067 0.066
Ztg 0.138 0.138 0.138 0.138 0.138 0.126 0.116 0.099 0.099 0.097
Zb 0.041 0.041 0.041 0.041 0.041 0.041 0.041 0.040 0.040 0.040
Slab top σt (kn/sqm) 26991 28090 29189 30288 31387 31675 32027 31938 33352 34659
Slab bott σi (kn/sqm) ‐11567 ‐10879 ‐10192 ‐9505 ‐8818 ‐8914 ‐8966 ‐9477 ‐8521 ‐7678
Girder top σi (kn/sqm) ‐11567 ‐10879 ‐10192 ‐9505 ‐8818 ‐8914 ‐8966 ‐9477 ‐8521 ‐7678
Girder bott σb (kn/sqm) 3320 1041 ‐1237 ‐3516 ‐5795 ‐8660 ‐11616 ‐15161 ‐17513 ‐20005
+ve sign denotes compression
‐ve tension
TEMPERATURE FALL CASE
T1 0.165
T1= 6.8 0C Temp at bottom of slab 0.0000
T2= 0.0 0C Temp at top of bot plates 7.5000
T3= 0.0 0C
T4= 8.0 0C
T4 0.40
S No.
1 0.0000 ‐16320
2 0.1650 0.1650 0 0.241 ‐325 0.055 0.592 ‐193
4 0.2750 0.1100 0 0.241 0 0.220 0.427 0
7 1.6500 0.0000 0 0.241 0 0
8 2.0250 0.3750 ‐18000 0.014 ‐47 1.900 ‐1.253 59
9 2.0500 0.0250 ‐19200 0.600 ‐279 2.038 ‐1.390 388
‐651 255
R=12.30 M=46
M=255
Page 51 of 156
Section 2 3 4 5 6 7 8 9 10 11
Di from end 1.9 4.4 6.9 9.4 11.9 14.4 16.9 19.4 21.9 24.4
Moment 231 200 170 139 108 77 47 16 ‐15 ‐46
A 0.102 0.102 0.102 0.102 0.102 0.098 0.093 0.086 0.086 0.086
Zt 0.086 0.086 0.086 0.086 0.086 0.081 0.075 0.067 0.067 0.066
Ztg 0.138 0.138 0.138 0.138 0.138 0.126 0.116 0.099 0.099 0.097
Zb 0.041 0.041 0.041 0.041 0.041 0.041 0.041 0.040 0.040 0.040
Slab top σt (kn/sqm) ‐12631 ‐12274 ‐11916 ‐11558 ‐11201 ‐10613 ‐9956 ‐9001 ‐8541 ‐8010
Slab bott σi (kn/sqm) 4696 4920 5143 5367 5591 6054 6579 7396 7707 8087
Girder top σi (kn/sqm) 4696 4920 5143 5367 5591 6054 6579 7396 7707 8087
Girder bott σb (kn/sqm) ‐7249 ‐7991 ‐8732 ‐9474 ‐10215 ‐10654 ‐11075 ‐11248 ‐12013 ‐12719
‐ve tension
5.2 INNER GIRDER
at span
Total depth of web h' 1.7500 m
Coeff of thermal expansion a 1.20E‐05 /0C
TEMPERATURE RISE CASE
T1= 20.50 0C Temp at slab bottom 3.14
T2= 4.00 0C
T3=
T1 0.272 0.188
0.165 T2 0.275 0.275
0.510
1.750 1.750
0.025 0.025
0.600 0.600
span section support section
Page 52 of 156
S No.
1 0.0000 49200
2 0.1650 0.165 9600 0.272 1320 0.064 0.540 713
3 0.2750 0.110 7529 0.272 256 0.218 0.386 99
4 0.675 0.400 0 0.014 21 0.408 0.196 4
5 2.0500 0 0 0.000 0
1597 816
R=37.80
M=816
M=106
Section 2 3 4 5 6 7 8 9 10 11
Di from end 1.9 4.4 6.9 9.4 11.9 14.4 16.9 19.4 21.9 24.4
Moment 744 650 555 461 366 272 177 83 ‐12 ‐106
A 0.110 0.110 0.110 0.110 0.110 0.105 0.100 0.100 0.092 0.091
Zt 0.096 0.096 0.096 0.096 0.096 0.090 0.084 0.084 0.074 0.073
Ztg 0.161 0.161 0.161 0.161 0.161 0.147 0.134 0.134 0.113 0.111
Zb 0.042 0.042 0.042 0.042 0.042 0.042 0.041 0.041 0.041 0.041
Slab top σt (kn/sqm) 26953 27935 28917 29899 30880 30980 31119 32242 31981 33121
Slab bott σi (kn/sqm) ‐11618 ‐11030 ‐10442 ‐9853 ‐9265 ‐9531 ‐9773 ‐9066 ‐9744 ‐9045
Girder top σi (kn/sqm) ‐11618 ‐11030 ‐10442 ‐9853 ‐9265 ‐9531 ‐9773 ‐9066 ‐9744 ‐9045
Girder bott σb (kn/sqm) 3170 924 ‐1322 ‐3568 ‐5813 ‐8710 ‐11703 ‐13982 ‐17668 ‐20139
+ve sign denotes compression ‐ve tension
TEMPERATURE FALL CASE
T1 0.165
T2 0.00 T1= 6.8 0C Temp at bottom of slab 0.0000
T2= 0.0 0C Temp at top of bot plates 7.5000
T3= 0.0 0C
T3 0.00 T4= 8.0 0C
T4 0.40
Page 53 of 156
S No.
1 0.0000 ‐16320
2 0.1650 0.165 0 0.272 ‐366 0.055 0.549 ‐201
3 0.2750 0.110 0 0.272 0 0.220 0.384 0
4 1.6500
5 2.0250 0.375 ‐18000 0.014 ‐47 1.900 ‐1.296 61
6 2.0500 0.025 ‐19200 0.600 ‐279 2.038 ‐1.434 400
‐693 260
R=12.00 M=33
M=260
Section 2 3 4 5 6 7 8 9 10 11
Di from end 1.9 4.4 6.9 9.4 11.9 14.4 16.9 19.4 21.9 24.4
Moment 237 207 177 147 117 87 57 27 ‐3 ‐33
A 0.110 0.110 0.110 0.110 0.110 0.105 0.100 0.100 0.092 0.091
Zt 0.096 0.096 0.096 0.096 0.096 0.090 0.084 0.084 0.074 0.073
Ztg 0.161 0.161 0.161 0.161 0.161 0.147 0.134 0.134 0.113 0.111
Zb 0.042 0.042 0.042 0.042 0.042 0.042 0.041 0.041 0.041 0.041
Slab top σt (kn/sqm) ‐12492 ‐12180 ‐11868 ‐11557 ‐11245 ‐10692 ‐10073 ‐9717 ‐8748 ‐8273
Slab bott σi (kn/sqm) 4817 5003 5190 5377 5564 6001 6498 6723 7559 7895
Girder top σi (kn/sqm) 4817 5003 5190 5377 5564 6001 6498 6723 7559 7895
Girder bott σb (kn/sqm) ‐7268 ‐7981 ‐8694 ‐9407 ‐10120 ‐10517 ‐10892 ‐11615 ‐11732 ‐12403
‐ve tension
Page 54 of 156
6 CALCULATION OF STRESSES DUE TO DIFF SHRINKAGE
6.1 OUTER GIRDER (median side)
SPAN
Total depth of girder h' 1.800 m
Shrinkage strain 2.00E‐04
Creep factor 0.430
Section modulus at top of girder Ztg 0.086
STRESS AT SPAN SECTION (kN/sqm)
0.1138 S NO. LOCATION
0.250 1 Deck Slab Top
2 Deck Slab Bottom
3 Steel Girder top
1.8 4 Steel Girder bottom
Typical X section Final Stress diagram
stress εdif x Es= 0.0002*200000000*0.43 1.7E+04 kN/sqm

Force 17200*0.11376*0.25 489 kN
y from top CG of deck slab from top 0.117 m
e yt‐0.114 (2.05‐1.232)‐0.117 0.701 m
M= 489*0.701 343 kNm
This moment is applied on continuous structure and following final Moment is obtained.
Page 55 of 156
M=1
R=14.10
M=343
Section 2 3 4 5 6 7 8 9 10 11
Di from end 1.9 4.4 6.9 9.4 11.9 14.4 16.9 19.4 21.9 24.4
Moment 316 281 245 210 175 140 104 69 34 ‐1
A 0.078 0.078 0.078 0.078 0.078 0.076 0.074 0.070 0.070 0.070
Zt 0.057 0.057 0.057 0.057 0.057 0.054 0.052 0.047 0.047 0.047
Ztg 0.082 0.082 0.082 0.082 0.082 0.077 0.072 0.065 0.065 0.064
Zb 0.039 0.039 0.039 0.039 0.039 0.039 0.039 0.038 0.038 0.038
1 σt (kn/sqm) ‐5431 ‐6048 ‐6664 ‐7280 ‐7897 ‐8205 ‐8555 ‐8774 ‐9525 ‐10241
2 σi (kn/sqm) ‐7085 ‐7517 ‐7949 ‐8381 ‐8813 ‐8955 ‐9132 ‐9176 ‐9722 ‐10234
3 σi (kn/sqm) 10115 9683 9251 8819 8387 8245 8068 8024 7478 6966
4 σb (kn/sqm) ‐1794 ‐898 ‐1 896 1792 2842 3914 5130 6057 7019
6.2 INNER GIRDER

at span
Total depth of girder h' 1.8 m
Shrinkage strain 2.00E‐04
Creep factor 0.43
Section modulus at top of girder Ztg 0.096
Page 56 of 156
0.142
0.25
1.8
Typical X section Final Stress diagram
stress εdif x Es= 0.0002*200000000*0.43 1.7E+04 kN/sqm

Force 17200*0.141568*0.25 608.7 kN
y from top CG of deck slab from top 0.107 m
e yt‐0.114 (2.05‐1.270)‐0.107 0.674 m
M= 608.7424*0.674 410 kNm
This moment is applied on continuous structure and following final Moment is obtained.
97
R=20.80
M=410
Section 2 3 4 5 6 7 8 9 10 11
Di from end 1.9 4.4 6.9 9.4 11.9 14.4 16.9 19.4 21.9 24.4
Moment 371 319 267 215 163 111 59 7 ‐45 ‐97
A 0.082 0.082 0.082 0.082 0.082 0.080 0.077 0.077 0.073 0.073
Zt 0.063 0.063 0.063 0.063 0.063 0.059 0.056 0.056 0.051 0.050
Ztg 0.091 0.091 0.091 0.091 0.091 0.085 0.080 0.080 0.071 0.070
Zb 0.040 0.040 0.040 0.040 0.040 0.040 0.039 0.039 0.039 0.039
1 σt (kn/sqm) ‐3884 ‐4714 ‐5544 ‐6374 ‐7203 ‐7704 ‐8273 ‐9198 ‐9774 ‐10770
2 σi (kn/sqm) ‐5738 ‐6308 ‐6878 ‐7447 ‐8017 ‐8272 ‐8583 ‐9234 ‐9522 ‐10227
3 σi (kn/sqm) 11462 10892 10322 9753 9183 8928 8617 7966 7678 6973
4 σb (kn/sqm) ‐1885 ‐583 719 2021 3323 4836 6384 7709 9486 10883
Page 57 of 156
7 FLEXURE CHECK
7.1 SUMMARY OF SECTION PROPERTIES
Girder with holes in flange Girder without holes in flange

Item Con. Stg Tans. Lod Perm Lod Con. Stg Tans. Lod Perm Lod
Tf (C Flange) 25 25 25 25 25 25
A 0.047 0.078 0.062 0.055 0.086 0.070
Ix‐x 0.024 0.044 0.036 0.030 0.051 0.043
Iy‐y 0.001 0.004 0.002 0.001 0.004 0.002
yi 0.900 0.488 0.642 0.900 0.525 0.671
yb 0.900 1.312 1.158 0.900 1.275 1.129
Zt ‐ 0.059 0.041 ‐ 0.066 0.047
Ztg 0.026 0.090 0.056 0.033 0.097 0.064
Zb 0.026 0.033 0.031 0.033 0.040 0.038
Yield stress for Plate thickness > 20 and < 40 mm 240 mpa
Allowable tension in bending = 148.8 mpa
= 148800 kN/sqm
7.2 CONSTRUCTION STAGE CHECK
Girder alone for self wt and weight of deck slab.
Outer/Inner Girder (with Holes)
lxx 5.00 m
rxx 0.713 m
ryy 0.139 m
rmin 0.139 m
slenderness ratio l= lxx/rmin 36.009
permissible bending stress in compression
c1 900.0 mm
c2 900.0 mm
D 1800 mm
T 25 mm
l 5000 mm
rmin 138.9 mm
k1= 1 for ψ = 1.000 (Refer Table G.6 of IRC 24)
k2= 0 for ω = 0.500 (Refer Table G.7 of IRC 24)
Y= 26.5x1e5/(5000/138.9)^2 = 2045 mpa
X= 2045*SQRT(1+(1/20)*(5000*25/(138.9*1800))^2) = 2058 mpa
fcb= 1*(2058+0*2045)(900/900) = 2058.0 mpa
allowable stress in bending comp (table G.5 of IRC24) 159.3 mpa
Basic permissible stress in bending comp (Table G.2) 148.8 mpa
Basic permissible stress in bending comp to be adopted 148.8 mpa
Outer/Inner Girder (Without holes)
lxx 5.00 m
rxx 0.740 m
ryy 0.129 m
rmin 0.129 m
c1 900 mm
c2 900 mm
D 1800 mm
T 25 mm
Page 58 of 156
l 5000 mm
rmin 128.5 mm
k1= 1.0 for ψ = 1.000 (Refer Table G.6 of IRC 24)
k2= 0.0 for ω = 0.500 (Refer Table G.7 of IRC 24)
Y= 26.5x1e5/(5000/128.5)^2 = 1750 mpa
X= 1750*SQRT(1+(1/20)*(5000*25/(128.5*1800))^2) = 1763 mpa
fcb= 1*(1763+0*1750)(900/900) = 1763 mpa
allowable stress in bending comp (table G.5 of IRC24) 157.6 mpa
Basic permissible stress in bending comp (Table G.2) 148.8 mpa
Basic permissible stress in bending comp to be adopted 148.8 mpa
Outer/Inner Girder during Service Stage

During service stage compression flange is either restrained by deck slab all along, or by bracings at bottom, giving permissible stress of
148.8 mpa in both the cases.
7.3 SECTION CHECK FOR CONSTRUCTION & SERVICE STAGE

Compressive stress +ve Tensile stress ‐ve Modular ratio for perm loads 15
Sagging BM ‐ve Hogging BM +ve Modular ratio for trans loads 7.5
Summary of Stresses
Outer Girder (median Side)
Description Section
DL SIDL Shutter. Const. LL Rem_sh Rem_CLL CWLL DL+SHUT+CON LL
M(kNm) ‐223 ‐111 0 ‐45 0 ‐45 ‐348
σt (mpa) slab 0.09 0 0.00 0.54
σi (mpa) slab 2 0.05 0 0.00 0.34
σi (mpa) girder 6.73 0.81 0.00 1.35 0 ‐1.35 2.53 8.07
σb (mpa) girder ‐6.73 ‐2.68 0.00 ‐1.35 0 1.35 ‐8.39 ‐8.07
M(kNm) ‐421 ‐198 0 ‐84 0 ‐84 ‐778
σt (mpa) slab 0.15 0 0.00 1.21
σi (mpa) slab 3 0.10 0 0.00 0.75
σi (mpa) girder 12.67 1.44 0.00 2.53 0 ‐2.53 5.66 15.21
σb (mpa) girder ‐12.67 ‐4.76 0.00 ‐2.53 0 2.53 ‐18.77 ‐15.21
M(kNm) ‐508 ‐219 0 ‐102 0 ‐102 ‐1158
σt (mpa) slab 0.17 0 0.00 1.80
GROSS SEC PROPERTIRS
σi (mpa) slab 4 0.11 0 0.00 1.12

σi (mpa) girder 15.31 1.59 0.00 3.06 0 ‐3.06 8.42 18.37
σb (mpa) girder ‐15.31 ‐5.27 0.00 ‐3.06 0 3.06 ‐27.91 ‐18.37
M(kNm) ‐486 ‐176 0 ‐97 0 ‐97 ‐1476
σt (mpa) slab 0.14 0 0.00 2.29
σi (mpa) slab 5 0.09 0 0.00 1.43
σi (mpa) girder 14.65 1.28 0.00 2.93 0 ‐2.93 10.74 17.58
σb (mpa) girder ‐14.65 ‐4.24 0.00 ‐2.93 0 2.93 ‐35.60 ‐17.58
M(kNm) ‐340 ‐120 0 ‐68 0 ‐68 ‐1521
σt (mpa) slab 0.09 0 0.00 2.36
σi (mpa) slab 6 0.06 0 0.00 1.48
σi (mpa) girder 10.25 0.87 0.00 2.05 0 ‐2.05 11.06 12.30
σb (mpa) girder ‐10.25 ‐2.90 0.00 ‐2.05 0 2.05 ‐36.69 ‐12.30
M(kNm) ‐71 ‐40 0 ‐14 0 ‐14 ‐1381
σt (mpa) slab 0.03 0 0.00 2.28
σi (mpa) slab 7 0.02 0 0.00 1.46
σi (mpa) girder 2.13 0.32 0.00 0.43 0 ‐0.43 10.92 2.56
σb (mpa) girder ‐2.13 ‐0.98 0.00 ‐0.43 0 0.43 ‐33.54 ‐2.56
M(kNm) 322 70 0 64 0 64 1036
σt (mpa) slab ‐0.07 0 0.00 ‐2.02
Page 59 of 156
σi (mpa) slab 8 ‐0.04 0 0.00 ‐1.28
σi (mpa) girder
NET SEC PRO
‐12.19 ‐0.64 0.00 ‐2.44 0 2.44 ‐9.57 ‐14.63

σb (mpa) girder 12.19 2.05 0.00 2.44 0 ‐2.44 30.44 14.63
M(kNm) 836 214 0 167 0 167 1148
σt (mpa) slab ‐0.24 0 0.00 ‐2.54
σi (mpa) slab 9 ‐0.16 0 0.00 ‐1.67
σi (mpa) girder ‐31.69 ‐2.35 0.00 ‐6.34 0 6.34 ‐12.56 ‐38.03
σb (mpa) girder 31.69 6.41 0.00 6.34 0 ‐6.34 34.33 38.03
M(kNm) 1460 424 0 292 0 292 1260
σt (mpa) slab ‐0.43 0 0.00 ‐2.55
σi (mpa) slab 10 ‐0.29 0 0.00 ‐1.73
σi (mpa) girder ‐43.97 ‐4.35 0.00 ‐8.79 0 8.79 ‐12.94 ‐52.77
σb (mpa) girder 43.97 10.56 0.00 8.79 0 ‐8.79 31.40 52.77
M(kNm) 2194 698 0 439 0 439 1294
GROSS SEC PRO
σt (mpa) slab ‐0.71 0 0.00 ‐2.62

σi (mpa) slab 11 ‐0.48 0 0.00 ‐1.77
σi (mpa) girder ‐66.08 ‐7.17 0.00 ‐13.22 0 13.22 ‐13.30 ‐79.29
σb (mpa) girder 66.08 17.39 0.00 13.22 0 ‐13.22 32.26 79.29
M(kNm) 1316 385 0 263 0 263 738
σt (mpa) slab ‐0.39 0 0.00 ‐1.49
σi (mpa) slab 12 ‐0.26 0 0.00 ‐1.01
σi (mpa) girder ‐39.64 ‐3.96 0.00 ‐7.93 0 7.93 ‐7.58 ‐47.57
σb (mpa) girder 39.64 9.60 0.00 7.93 0 ‐7.93 18.39 47.57
M(kNm) 548 137 0 110 0 110 562
σt (mpa) slab ‐0.14 0 0.00 ‐1.11
σi (mpa) slab 13 ‐0.09 0 0.00 ‐0.70
σi (mpa) girder
NET SEC PRO
‐20.78 ‐1.29 0.00 ‐4.16 0 4.16 ‐5.28 ‐24.93

σb (mpa) girder 20.78 4.04 0.00 4.16 0 ‐4.16 16.55 24.93
M(kNm) ‐110 ‐46 0 ‐22 0 ‐22 ‐797
σt (mpa) slab 0.05 0 0.00 1.57
σi (mpa) slab 14 0.03 0 0.00 1.00
σi (mpa) girder 4.19 0.43 0.00 0.84 0 ‐0.84 7.49 5.02
σb (mpa) girder ‐4.19 ‐1.35 0.00 ‐0.84 0 0.84 ‐23.47 ‐5.02
M(kNm) ‐647 ‐193 0 ‐129 0 ‐129 ‐1209
σt (mpa) slab 0.16 0 0.00 1.94
σi (mpa) slab 15 0.10 0 0.00 1.23

σi (mpa) girder 19.49 1.47 0.00 3.90 0 ‐3.90 9.21 23.39
σb (mpa) girder ‐19.49 ‐4.68 0.00 ‐3.90 0 3.90 ‐29.26 ‐23.39
M(kNm) ‐1061 ‐312 0 ‐212 0 ‐212 ‐1543
σt (mpa) slab 0.25 0 0.00 2.48
σi (mpa) slab 16 0.16 0 0.00 1.57
σi (mpa) girder 31.95 2.37 0.00 6.39 0 ‐6.39 11.75 38.34
σb (mpa) girder ‐31.95 ‐7.54 0.00 ‐6.39 0 6.39 ‐37.34 ‐38.34
M(kNm) ‐1351 ‐410 0 ‐270 0 ‐270 ‐1767
NET SEC PRO
σt (mpa) slab 0.35 0 0.00 2.97

σi (mpa) slab 17 0.21 0 0.00 1.78
σi (mpa) girder 51.21 3.10 0.00 10.24 0 ‐10.24 13.36 61.45
σb (mpa) girder ‐51.21 ‐11.84 0.00 ‐10.24 0 10.24 ‐51.00 ‐61.45
M(kNm) ‐1515 ‐506 0 ‐303 0 ‐303 ‐1767
σt (mpa) slab 0.39 0 0.00 2.72
PROPERTIRS
σi (mpa) slab 18 0.24 0 0.00 1.69

σi (mpa) girder 45.63 3.64 0.00 9.13 0 ‐9.13 12.70 54.76
σb (mpa) girder ‐45.63 ‐12.19 0.00 ‐9.13 0 9.13 ‐42.57 ‐54.76
Page 60 of 156
GROSS SEC P
M(kNm) ‐1570 ‐538 0 ‐314 0 ‐314 ‐1766
σt (mpa) slab 0.40 0 0.00 2.61
σi (mpa) slab 19 0.24 0 0.00 1.60
σi (mpa) girder 47.28 3.65 0.00 9.46 0 ‐9.46 12.00 56.74
σb (mpa) girder ‐47.28 ‐12.89 0.00 ‐9.46 0 9.46 ‐42.36 ‐56.74
Inner Girder
Description Section
M(kNm) ‐227 ‐105 0 ‐45 0 ‐45 ‐594
σt (mpa) slab 0.07 0 0.00 0.82
σi (mpa) slab 2 0.04 0 0.00 0.49
σi (mpa) girder 6.83 0.65 0.00 1.37 0 ‐1.37 3.70 8.20
σb (mpa) girder ‐6.83 ‐2.49 0.00 ‐1.37 0 1.37 ‐14.11 ‐8.20
M(kNm) ‐427 ‐195 0 ‐85 0 ‐85 ‐1079
σt (mpa) slab 0.13 0 0.00 1.50
σi (mpa) slab 3 0.08 0 0.00 0.90
σi (mpa) girder 12.87 1.21 0.00 2.57 0 ‐2.57 6.72 15.44
σb (mpa) girder ‐12.87 ‐4.63 0.00 ‐2.57 0 2.57 ‐25.65 ‐15.44
M(kNm) ‐516 ‐231 0 ‐103 0 ‐103 ‐1304
σt (mpa) slab 0.16 0 0.00 1.81
σi (mpa) slab 4 0.10 0 0.00 1.08

σi (mpa) girder 15.54 1.44 0.00 3.11 0 ‐3.11 8.12 18.65
σb (mpa) girder ‐15.54 ‐5.48 0.00 ‐3.11 0 3.11 ‐31.00 ‐18.65
M(kNm) ‐493 ‐212 ‐99 0 ‐99 ‐1271
σt (mpa) slab 0.15 0 0.00 1.76
σi (mpa) slab 5 0.09 0 0.00 1.05
σi (mpa) girder 14.86 1.32 0.00 2.97 0 ‐2.97 7.91 17.83
σb (mpa) girder ‐14.86 ‐5.04 0.00 ‐2.97 0 2.97 ‐30.21 ‐17.83
M(kNm) ‐347 ‐149 0 ‐69 0 ‐69 ‐1282
σt (mpa) slab 0.10 0 0.00 1.78
σi (mpa) slab 6 0.06 0 0.00 1.06
σi (mpa) girder 10.44 0.93 0.00 2.09 0 ‐2.09 7.98 12.53
σb (mpa) girder ‐10.44 ‐3.55 0.00 ‐2.09 0 2.09 ‐30.46 ‐12.53
M(kNm) ‐76 ‐37 0 ‐15 0 ‐15 ‐1170
σt (mpa) slab 0.03 0 0.00 1.73
σi (mpa) slab 7 0.02 0 0.00 1.06
σi (mpa) girder 2.30 0.25 0.00 0.46 0 ‐0.46 7.97 2.76
σb (mpa) girder ‐2.30 ‐0.88 0.00 ‐0.46 0 0.46 ‐28.00 ‐2.76
M(kNm) 319 126 0 64 0 64 859
σt (mpa) slab ‐0.11 0 0.00 ‐1.49
σi (mpa) slab 8 ‐0.07 0 0.00 ‐0.90
σi (mpa) girder
NET SEC PRO
‐12.10 ‐1.00 0.00 ‐2.42 0 2.42 ‐6.79 ‐14.52

σb (mpa) girder 12.10 3.65 0.00 2.42 0 ‐2.42 24.84 14.52
M(kNm) 837 338 0 167 0 167 970
σt (mpa) slab ‐0.29 0 0.00 ‐1.68
σi (mpa) slab 9 ‐0.18 0 0.00 ‐1.02
σi (mpa) girder ‐31.72 ‐2.67 0.00 ‐6.34 0 6.34 ‐7.66 ‐38.07
σb (mpa) girder 31.72 9.76 0.00 6.34 0 ‐6.34 28.05 38.07
M(kNm) 1467 604 0 293 0 293 1083
σt (mpa) slab ‐0.54 0 0.00 ‐1.94
σi (mpa) slab 10 ‐0.36 0 0.00 ‐1.28
σi (mpa) girder ‐44.19 ‐5.34 0.00 ‐8.84 0 8.84 ‐9.56 ‐53.03
σb (mpa) girder 44.19 14.80 0.00 8.84 0 ‐8.84 26.54 53.03
Page 61 of 156
M(kNm) 2210 925 0 442 0 442 1129
GROSS SEC PRO
σt (mpa) slab ‐0.84 0 0.00 ‐2.05

σi (mpa) slab 11 ‐0.55 0 0.00 ‐1.35
σi (mpa) girder ‐66.55 ‐8.31 0.00 ‐13.31 0 13.31 ‐10.14 ‐79.86
σb (mpa) girder 66.55 22.71 0.00 13.31 0 ‐13.31 27.70 79.86
M(kNm) 1324 539 0 265 0 265 653
σt (mpa) slab ‐0.49 0 0.00 ‐1.19
σi (mpa) slab 12 ‐0.32 0 0.00 ‐0.78
σi (mpa) girder ‐39.88 ‐4.84 0.00 ‐7.98 0 7.98 ‐5.87 ‐47.86
σb (mpa) girder 39.88 13.23 0.00 7.98 0 ‐7.98 16.03 47.86
M(kNm) 550 208 0 110 0 110 504
σt (mpa) slab ‐0.18 0 0.00 ‐0.88
σi (mpa) slab 13 ‐0.11 0 0.00 ‐0.54
σi (mpa) girder
NET SEC PRO
‐20.86 ‐1.67 0.00 ‐4.17 0 4.17 ‐4.05 ‐25.03

σb (mpa) girder 20.86 6.02 0.00 4.17 0 ‐4.17 14.59 25.03
M(kNm) ‐112 ‐69 0 ‐22 0 ‐22 ‐741
σt (mpa) slab 0.06 0 0.00 1.30
σi (mpa) slab 14 0.04 0 0.00 0.79
σi (mpa) girder 4.25 0.55 0.00 0.85 0 ‐0.85 5.95 5.10
σb (mpa) girder ‐4.25 ‐1.98 0.00 ‐0.85 0 0.85 ‐21.46 ‐5.10
M(kNm) ‐649 ‐296 0 ‐130 0 ‐130 ‐1041
σt (mpa) slab 0.21 0 0.00 1.49
σi (mpa) slab 15 0.13 0 0.00 0.91

σi (mpa) girder 19.56 1.93 0.00 3.91 0 ‐3.91 6.81 23.47
σb (mpa) girder ‐19.56 ‐7.06 0.00 ‐3.91 0 3.91 ‐24.84 ‐23.47
M(kNm) ‐1063 ‐473 0 ‐213 0 ‐213 ‐1274
σt (mpa) slab 0.34 0 0.00 1.83
σi (mpa) slab 16 0.21 0 0.00 1.11
σi (mpa) girder 32.00 3.09 0.00 6.40 0 ‐6.40 8.33 38.40
σb (mpa) girder ‐32.00 ‐11.27 0.00 ‐6.40 0 6.40 ‐30.40 ‐38.40
M(kNm) ‐1353 ‐599 0 ‐271 0 ‐271 ‐1460
NET SEC PRO
σt (mpa) slab 0.45 0 0.00 2.18

σi (mpa) slab 17 0.25 0 0.00 1.24
σi (mpa) girder 51.29 3.82 0.00 10.26 0 ‐10.26 9.31 61.54
σb (mpa) girder ‐51.29 ‐17.02 0.00 ‐10.26 0 10.26 ‐41.48 ‐61.54
M(kNm) ‐1520 ‐680 0 ‐304 0 ‐304 ‐1778
σt (mpa) slab 0.45 0 0.00 2.34
σi (mpa) slab 18 0.26 0 0.00 1.37

σi (mpa) girder 45.78 3.94 0.00 9.16 0 ‐9.16 10.29 54.94
σb (mpa) girder ‐45.78 ‐16.09 0.00 ‐9.16 0 9.16 ‐42.02 ‐54.94
M(kNm) ‐1576 ‐708 0 ‐315 0 ‐315 ‐1778
σt (mpa) slab 0.47 0 0.00 2.34
σi (mpa) slab 19 0.27 0 0.00 1.37
σi (mpa) girder 47.46 4.10 0.00 9.49 0 ‐9.49 10.29 56.95
σb (mpa) girder ‐47.46 ‐16.73 0.00 ‐9.49 0 9.49 ‐42.02 ‐56.95
Outer Girder (Footpath Side)

Description Section
M(kNm) ‐223 ‐139 0 ‐45 0 ‐45 ‐207
σt (mpa) slab 0.11 0 0.00 0.32
σi (mpa) slab 2 0.07 0 0.00 0.20
Page 62 of 156
σi (mpa) girder 6.73 1.01 0.00 1.35 0 ‐1.35 1.51 8.07
σb (mpa) girder ‐6.73 ‐3.35 0.00 ‐1.35 0 1.35 ‐4.99 ‐8.07
M(kNm) ‐421 ‐254 0 ‐84 0 ‐84 ‐420
σt (mpa) slab 0.20 0 0.00 0.65
σi (mpa) slab 3 0.12 0 0.00 0.41
σi (mpa) girder 12.67 1.84 0.00 2.53 0 ‐2.53 3.05 15.21
σb (mpa) girder ‐12.67 ‐6.12 0.00 ‐2.53 0 2.53 ‐10.12 ‐15.21
M(kNm) ‐508 ‐294 0 ‐102 0 ‐102 ‐616
σt (mpa) slab 0.23 0 0.00 0.96
σi (mpa) slab 4 0.14 0 0.00 0.60

σi (mpa) girder 15.31 2.14 0.00 3.06 0 ‐3.06 4.48 18.37
σb (mpa) girder ‐15.31 ‐7.08 0.00 ‐3.06 0 3.06 ‐14.85 ‐18.37
M(kNm) ‐486 ‐261 0 ‐97 0 ‐97 ‐801
σt (mpa) slab 0.20 0 0.00 1.24
σi (mpa) slab 5 0.13 0 0.00 0.78
σi (mpa) girder 14.65 1.90 0.00 2.93 0 ‐2.93 5.82 17.58
σb (mpa) girder ‐14.65 ‐6.29 0.00 ‐2.93 0 2.93 ‐19.31 ‐17.58
M(kNm) ‐340 ‐182 0 ‐68 0 ‐68 ‐845
σt (mpa) slab 0.14 0 0.00 1.31
σi (mpa) slab 6 0.09 0 0.00 0.82
σi (mpa) girder 10.25 1.32 0.00 2.05 0 ‐2.05 6.14 12.30
σb (mpa) girder ‐10.25 ‐4.39 0.00 ‐2.05 0 2.05 ‐20.37 ‐12.30
M(kNm) ‐71 ‐58 0 ‐14 0 ‐14 ‐764
σt (mpa) slab 0.05 0 0.00 1.26
σi (mpa) slab 7 0.03 0 0.00 0.81
σi (mpa) girder 2.13 0.46 0.00 0.43 0 ‐0.43 6.05 2.56
σb (mpa) girder ‐2.13 ‐1.41 0.00 ‐0.43 0 0.43 ‐18.56 ‐2.56
M(kNm) 322 115 0 64 0 64 ‐572
σt (mpa) slab ‐0.11 0 0.00 1.11
σi (mpa) slab 8 ‐0.07 0 0.00 0.70
σi (mpa) girder
NET SEC PRO
‐12.19 ‐1.06 0.00 ‐2.44 0 2.44 5.29 ‐14.63

σb (mpa) girder 12.19 3.38 0.00 2.44 0 ‐2.44 ‐16.81 14.63
M(kNm) 836 344 0 167 0 167 840
σt (mpa) slab ‐0.38 0 0.00 ‐1.86
σi (mpa) slab 9 ‐0.25 0 0.00 ‐1.23
σi (mpa) girder ‐31.69 ‐3.76 0.00 ‐6.34 0 6.34 ‐9.20 ‐38.03
σb (mpa) girder 31.69 10.29 0.00 6.34 0 ‐6.34 25.13 38.03
M(kNm) 1460 646 0 292 0 292 977
σt (mpa) slab ‐0.65 0 0.00 ‐1.98
σi (mpa) slab 10 ‐0.44 0 0.00 ‐1.34
σi (mpa) girder ‐43.97 ‐6.64 0.00 ‐8.79 0 8.79 ‐10.04 ‐52.77
σb (mpa) girder 43.97 16.11 0.00 8.79 0 ‐8.79 24.37 52.77
M(kNm) 2194 1022 0 439 0 439 903
GROSS SEC PRO
σt (mpa) slab ‐1.03 0 0.00 ‐1.83

σi (mpa) slab 11 ‐0.70 0 0.00 ‐1.24
σi (mpa) girder ‐66.08 ‐10.50 0.00 ‐13.22 0 13.22 ‐9.28 ‐79.29
σb (mpa) girder 66.08 25.48 0.00 13.22 0 ‐13.22 22.52 79.29
M(kNm) 1316 584 0 263 0 263 476
σt (mpa) slab ‐0.59 0 0.00 ‐0.96
σi (mpa) slab 12 ‐0.40 0 0.00 ‐0.65
σi (mpa) girder ‐39.64 ‐6.00 0.00 ‐7.93 0 7.93 ‐4.89 ‐47.57
σb (mpa) girder 39.64 14.56 0.00 7.93 0 ‐7.93 11.86 47.57
M(kNm) 548 220 0 110 0 110 300
Page 63 of 156
σt (mpa) slab ‐0.22 0 0.00 ‐0.59
σi (mpa) slab 13 ‐0.14 0 0.00 ‐0.38
σi (mpa) girder
NET SEC PRO
‐20.78 ‐2.06 0.00 ‐4.16 0 4.16 ‐2.81 ‐24.93

σb (mpa) girder 20.78 6.46 0.00 4.16 0 ‐4.16 8.82 24.93
M(kNm) ‐110 ‐72 0 ‐22 0 ‐22 ‐474
σt (mpa) slab 0.07 0 0.00 0.93
σi (mpa) slab 14 0.04 0 0.00 0.59
σi (mpa) girder 4.19 0.67 0.00 0.84 0 ‐0.84 4.45 5.02
σb (mpa) girder ‐4.19 ‐2.11 0.00 ‐0.84 0 0.84 ‐13.96 ‐5.02
M(kNm) ‐647 ‐307 0 ‐129 0 ‐129 ‐802
σt (mpa) slab 0.25 0 0.00 1.29
σi (mpa) slab 15 0.16 0 0.00 0.81

σi (mpa) girder 19.49 2.34 0.00 3.90 0 ‐3.90 6.11 23.39
σb (mpa) girder ‐19.49 ‐7.42 0.00 ‐3.90 0 3.90 ‐19.40 ‐23.39
M(kNm) ‐1061 ‐494 0 ‐212 0 ‐212 ‐1038
σt (mpa) slab 0.40 0 0.00 1.67
σi (mpa) slab 16 0.25 0 0.00 1.05
σi (mpa) girder 31.95 3.76 0.00 6.39 0 ‐6.39 7.90 38.34
σb (mpa) girder ‐31.95 ‐11.95 0.00 ‐6.39 0 6.39 ‐25.12 ‐38.34
M(kNm) ‐1351 ‐640 0 ‐270 0 ‐270 ‐1142
NET SEC PRO
σt (mpa) slab 0.54 0 0.00 1.92

σi (mpa) slab 17 0.32 0 0.00 1.15
σi (mpa) girder 51.21 4.84 0.00 10.24 0 ‐10.24 8.64 61.45
σb (mpa) girder ‐51.21 ‐18.47 0.00 ‐10.24 0 10.24 ‐32.97 ‐61.45
M(kNm) ‐1515 ‐750 0 ‐303 0 ‐303 ‐1110
σt (mpa) slab 0.58 0 0.00 1.71
σi (mpa) slab 18 0.36 0 0.00 1.06

σi (mpa) girder 45.63 5.39 0.00 9.13 0 ‐9.13 7.98 54.76
σb (mpa) girder ‐45.63 ‐18.06 0.00 ‐9.13 0 9.13 ‐26.74 ‐54.76
M(kNm) ‐1570 ‐786 0 ‐314 0 ‐314 ‐937
σt (mpa) slab 0.58 0 0.00 1.38
σi (mpa) slab 19 0.36 0 0.00 0.85
σi (mpa) girder 47.28 5.34 0.00 9.46 0 ‐9.46 6.37 56.74
σb (mpa) girder ‐47.28 ‐18.85 0.00 ‐9.46 0 9.46 ‐22.48 ‐56.74
Summary of Permissible Stresses

For plate thickness > 20 but < 40
Bending tension/(comp with SDL, LL etc) in steel Girder = 148.8 mpa with temp 171.12
Support L/8 L/4 3L/8 L/2
Bending Outer Girder 148.8 148.8 148.8 148.8 148.8
Compression Inner Girder 148.8 148.8 148.8 148.8 148.8
Concrete 16.67
Summary of Stresses in Outer Girder (median side)

C1 C2 C3 C4 C5 C6 C7 C8 C9
Description Section
DL+SHUT DL+SDL C2+LL C2+T(R) C2+T( F) C4+.5LL C5+.5LL C5+DS C8+0.5LL
σt (mpa) slab 0.00 0.09 0.63 3.69 ‐1.60 3.96 ‐1.33 ‐1.96 ‐1.69
Status OK OK OK OK OK OK OK OK OK
Reinf (mm2/m)
σi (mpa) slab 0.00 0.05 0.39 ‐1.49 0.68 ‐1.32 0.85 0.21 0.38
Status 2 OK OK OK OK OK OK OK OK OK
Page 64 of 156
σi (mpa) girder 6.73 7.54 10.07 ‐4.03 12.23 ‐2.77 13.50 22.35 23.61
σb (mpa) girder ‐6.73 ‐9.41 ‐17.80 ‐6.09 ‐16.66 ‐10.29 ‐20.86 ‐18.45 ‐22.65
σt (mpa) slab 0.00 0.15 1.36 3.90 ‐1.48 4.50 ‐0.88 ‐1.89 ‐1.28
Reinf (mm2/m)
σi (mpa) slab 0.00 0.10 0.85 ‐1.35 0.75 ‐0.98 1.13 0.25 0.63
σi (mpa) girder 12.67 14.11 19.77 3.23 19.03 6.06 21.86 28.71 31.54
σb (mpa) girder ‐12.67 ‐17.44 ‐36.20 ‐16.39 ‐25.43 ‐25.78 ‐34.81 ‐26.32 ‐35.71
σt (mpa) slab 0.00 0.17 1.96 4.06 ‐1.42 4.96 ‐0.52 ‐1.86 ‐0.97
Reinf (mm2/m)
σi (mpa) slab 0.00 0.11 1.23 ‐1.25 0.79 ‐0.69 1.35 0.26 0.82
σi (mpa) girder 15.31 16.90 25.32 6.71 22.04 10.92 26.25 31.30 35.50
σb (mpa) girder ‐15.31 ‐20.58 ‐48.49 ‐21.82 ‐29.32 ‐35.78 ‐43.27 ‐29.32 ‐43.27
σt (mpa) slab 0.00 0.14 2.43 4.17 ‐1.40 5.32 ‐0.26 ‐1.89 ‐0.75
Reinf (mm2/m)
σi (mpa) slab 0.00 0.09 1.52 ‐1.18 0.80 ‐0.47 1.52 0.24 0.96
σi (mpa) girder 14.65 15.93 26.67 6.42 21.30 11.79 26.66 30.11 35.48
σb (mpa) girder ‐14.65 ‐18.89 ‐54.49 ‐22.41 ‐28.36 ‐40.21 ‐46.17 ‐27.47 ‐45.27
σt (mpa) slab 0.00 0.09 2.45 4.28 ‐1.40 5.46 ‐0.22 ‐1.93 ‐0.75
Reinf (mm2/m)
σi (mpa) slab 0.00 0.06 1.53 ‐1.12 0.80 ‐0.38 1.54 0.22 0.95
σi (mpa) girder 10.25 11.13 22.19 2.31 16.72 7.84 22.25 25.11 30.64
σb (mpa) girder ‐10.25 ‐13.15 ‐49.84 ‐18.94 ‐23.36 ‐37.29 ‐41.71 ‐21.57 ‐39.92
σt (mpa) slab 0.00 0.03 2.31 4.26 ‐1.38 5.40 ‐0.24 ‐1.93 ‐0.79
Reinf (mm2/m)
σi (mpa) slab 0.00 0.02 1.48 ‐1.17 0.83 ‐0.44 1.56 0.23 0.96
σi (mpa) girder 2.13 2.45 13.38 ‐6.46 8.51 ‐1.00 13.97 16.75 22.21
σb (mpa) girder ‐2.13 ‐3.11 ‐36.65 ‐11.77 ‐13.77 ‐28.54 ‐30.54 ‐10.93 ‐27.69
σt (mpa) slab 0.00 ‐0.07 ‐2.09 4.20 ‐1.40 3.19 ‐2.40 ‐1.97 ‐2.97
Reinf (mm2/m)
σi (mpa) slab 0.00 ‐0.04 ‐1.32 ‐1.24 0.83 ‐1.88 0.20 0.23 ‐0.41
Page 65 of 156
σi (mpa) girder ‐12.19 ‐12.84 ‐22.41 ‐21.80 ‐6.26 ‐26.59 ‐11.04 1.81 ‐2.98
σb (mpa) girder 12.19 14.24 44.68 2.62 3.16 17.85 18.39 7.08 22.30
σt (mpa) slab 0.00 ‐0.24 ‐2.78 4.02 ‐1.44 2.75 ‐2.71 ‐2.02 ‐3.29
Reinf (mm2/m)
σi (mpa) slab 0.00 ‐0.16 ‐1.83 ‐1.42 0.83 ‐2.26 ‐0.01 0.22 ‐0.62
σi (mpa) girder ‐31.69 ‐34.04 ‐46.60 ‐43.52 ‐26.64 ‐49.80 ‐32.92 ‐18.62 ‐24.90
σb (mpa) girder 31.69 38.11 72.44 22.95 26.86 40.11 44.03 31.99 49.16
σt (mpa) slab 0.00 ‐0.43 ‐2.98 4.02 ‐1.57 2.75 ‐2.84 ‐2.20 ‐3.48
Reinf (mm2/m)
σi (mpa) slab 0.00 ‐0.29 ‐2.02 ‐1.43 0.74 ‐2.29 ‐0.13 0.09 ‐0.77
σi (mpa) girder ‐43.97 ‐48.33 ‐61.27 ‐56.85 ‐40.62 ‐63.32 ‐47.09 ‐33.14 ‐39.61
σb (mpa) girder 43.97 54.53 85.94 37.02 42.52 52.72 58.22 48.58 64.28
σt (mpa) slab 0.00 ‐0.71 ‐3.32 3.92 ‐1.77 2.61 ‐3.08 ‐2.46 ‐3.76
Reinf (mm2/m)
σi (mpa) slab 0.00 ‐0.48 ‐2.25 ‐1.50 0.60 ‐2.39 ‐0.29 ‐0.08 ‐0.97
σi (mpa) girder ‐66.08 ‐73.25 ‐86.54 ‐80.92 ‐65.16 ‐87.57 ‐71.81 ‐58.19 ‐64.84
σb (mpa) girder 66.08 83.47 115.73 63.46 70.75 79.59 86.88 77.77 93.90
σt (mpa) slab 0.00 ‐0.39 ‐1.88 4.23 ‐1.46 3.49 ‐2.20 ‐2.14 ‐2.89
Reinf (mm2/m)
σi (mpa) slab 0.00 ‐0.26 ‐1.27 ‐1.29 0.81 ‐1.79 0.31 0.13 ‐0.37
σi (mpa) girder ‐39.64 ‐43.60 ‐51.18 ‐51.27 ‐35.51 ‐55.06 ‐39.30 ‐28.54 ‐32.33
σb (mpa) girder 39.64 49.24 67.63 29.23 36.52 38.43 45.72 43.54 52.73
σt (mpa) slab 0.00 ‐0.14 ‐1.24 4.49 ‐1.20 3.93 ‐1.76 ‐1.89 ‐2.44
Reinf (mm2/m)
σi (mpa) slab 0.00 ‐0.09 ‐0.79 ‐1.11 0.99 ‐1.46 0.64 0.31 ‐0.04
σi (mpa) girder ‐20.78 ‐22.07 ‐27.35 ‐29.75 ‐13.98 ‐32.38 ‐16.62 ‐7.01 ‐9.65
σb (mpa) girder 20.78 24.82 41.37 4.81 12.10 13.09 20.37 19.12 27.39
σt (mpa) slab 0.00 0.05 1.62 4.67 ‐1.02 5.45 ‐0.24 ‐1.71 ‐0.92
Reinf (mm2/m)
Page 66 of 156
σi (mpa) slab 0.00 0.03 1.03 ‐1.00 1.11 ‐0.50 1.61 0.42 0.92
σi (mpa) girder 4.19 4.62 12.10 ‐3.06 12.70 0.68 16.45 19.67 23.41
σb (mpa) girder ‐4.19 ‐5.53 ‐29.00 ‐25.54 ‐18.25 ‐37.27 ‐29.99 ‐11.23 ‐22.97
σt (mpa) slab 0.00 0.16 2.10 4.78 ‐0.91 5.75 0.06 ‐1.60 ‐0.63
Reinf (mm2/m)
σi (mpa) slab 0.00 0.10 1.33 ‐0.93 1.18 ‐0.31 1.79 0.49 1.11
σi (mpa) girder 19.49 20.96 30.17 13.29 29.05 17.89 33.65 36.02 40.62
σb (mpa) girder ‐19.49 ‐24.17 ‐53.44 ‐44.18 ‐36.89 ‐58.81 ‐51.52 ‐29.87 ‐44.50
σt (mpa) slab 0.00 0.25 2.73 4.87 ‐0.82 6.11 0.42 ‐1.50 ‐0.26
Reinf (mm2/m)
σi (mpa) slab 0.00 0.16 1.72 ‐0.87 1.24 ‐0.08 2.02 0.55 1.34
σi (mpa) girder 31.95 34.33 46.07 26.65 42.41 32.52 48.29 49.38 55.25
σb (mpa) girder ‐31.95 ‐39.50 ‐76.83 ‐59.50 ‐52.21 ‐78.17 ‐70.88 ‐45.20 ‐63.86
σt (mpa) slab 0.00 0.35 3.32 4.97 ‐0.72 6.45 0.76 ‐1.41 0.08
Reinf (mm2/m)
σi (mpa) slab 0.00 0.21 1.99 ‐0.82 1.28 0.07 2.18 0.60 1.49
σi (mpa) girder 51.21 54.31 67.67 46.63 62.40 53.31 69.07 69.36 76.04
σb (mpa) girder ‐51.21 ‐63.05 ‐114.04 ‐83.05 ‐75.77 ‐108.55 ‐101.26 ‐68.75 ‐94.24
σt (mpa) slab 0.00 0.39 3.11 5.01 ‐0.68 6.37 0.68 ‐1.36 0.00
Reinf (mm2/m)
σi (mpa) slab 0.00 0.24 1.94 ‐0.78 1.32 0.07 2.17 0.64 1.48
σi (mpa) girder 45.63 49.27 61.97 41.59 57.35 47.94 63.70 64.32 70.67
σb (mpa) girder ‐45.63 ‐57.82 ‐100.39 ‐77.82 ‐70.54 ‐99.11 ‐91.82 ‐63.52 ‐84.81
σt (mpa) slab 0.00 0.40 3.00 5.02 ‐0.67 6.32 0.63 ‐1.35 ‐0.05
Reinf (mm2/m)
σi (mpa) slab 0.00 0.24 1.84 ‐0.78 1.32 0.02 2.12 0.64 1.44
σi (mpa) girder 47.28 50.94 62.93 43.26 59.02 49.26 65.02 65.99 71.99
σb (mpa) girder ‐47.28 ‐60.18 ‐102.54 ‐80.18 ‐72.90 ‐101.36 ‐94.08 ‐65.88 ‐87.06
Summary of Stresses in Inner Girder
C1 C2 C3 C4 C5 C6 C7 C8 C9
Description Section
Page 67 of 156
Description Section
σt (mpa) slab 0.00 0.07 0.90 3.67 ‐1.59 4.08 ‐1.18 ‐1.85 ‐1.44
Reinf (mm2/m)
σi (mpa) slab 0.00 0.04 0.54 ‐1.51 0.69 ‐1.26 0.93 0.30 0.55
σi (mpa) girder 6.83 7.49 11.18 ‐4.13 12.30 ‐2.28 14.15 23.77 25.61
σb (mpa) girder ‐6.83 ‐9.32 ‐23.44 ‐6.15 ‐16.59 ‐13.21 ‐23.65 ‐18.48 ‐25.53
σt (mpa) slab 0.00 0.13 1.63 3.86 ‐1.49 4.61 ‐0.74 ‐1.80 ‐1.06
Reinf (mm2/m)
σi (mpa) slab 0.00 0.08 0.98 ‐1.39 0.75 ‐0.94 1.20 0.33 0.78
σi (mpa) girder 12.87 14.08 20.80 3.05 19.09 6.41 22.44 29.98 33.34
σb (mpa) girder ‐12.87 ‐17.50 ‐43.15 ‐16.57 ‐25.48 ‐29.40 ‐38.30 ‐26.06 ‐38.89
σt (mpa) slab 0.00 0.16 1.97 4.02 ‐1.42 4.92 ‐0.52 ‐1.79 ‐0.89
Reinf (mm2/m)
σi (mpa) slab 0.00 0.10 1.18 ‐1.30 0.79 ‐0.76 1.33 0.33 0.87
σi (mpa) girder 15.54 16.98 25.10 6.53 22.17 10.59 26.23 32.49 36.55
σb (mpa) girder ‐15.54 ‐21.02 ‐52.02 ‐22.34 ‐29.72 ‐37.84 ‐45.21 ‐29.00 ‐44.50
σt (mpa) slab 0.00 0.15 1.91 4.13 ‐1.39 5.01 ‐0.51 ‐1.82 ‐0.94
Reinf (mm2/m)
σi (mpa) slab 0.00 0.09 1.14 ‐1.23 0.80 ‐0.70 1.33 0.31 0.84
σi (mpa) girder 14.86 16.18 24.09 6.32 21.55 10.28 25.51 31.31 35.26
σb (mpa) girder ‐14.86 ‐19.90 ‐50.10 ‐23.47 ‐29.30 ‐38.57 ‐44.41 ‐28.41 ‐43.51
σt (mpa) slab 0.00 0.10 1.88 4.22 ‐1.40 5.11 ‐0.51 ‐1.88 ‐0.99
Reinf (mm2/m)
σi (mpa) slab 0.00 0.06 1.13 ‐1.17 0.80 ‐0.64 1.34 0.27 0.80
σi (mpa) girder 10.44 11.37 19.35 2.10 16.93 6.09 20.92 26.12 30.11
σb (mpa) girder ‐10.44 ‐13.99 ‐44.45 ‐19.80 ‐24.11 ‐35.03 ‐39.34 ‐20.79 ‐36.01
σt (mpa) slab 0.00 0.03 1.76 4.16 ‐1.40 5.02 ‐0.53 ‐1.91 ‐1.05
Reinf (mm2/m)
σi (mpa) slab 0.00 0.02 1.08 ‐1.25 0.82 ‐0.72 1.35 0.27 0.80
σi (mpa) girder 2.30 2.55 10.52 ‐6.98 8.55 ‐3.00 12.54 17.48 21.46
Page 68 of 156
σb (mpa) girder ‐2.30 ‐3.18 ‐31.19 ‐11.89 ‐13.70 ‐25.89 ‐27.70 ‐8.86 ‐22.86
σt (mpa) slab 0.00 ‐0.11 ‐1.60 4.04 ‐1.45 3.29 ‐2.20 ‐2.00 ‐2.75
Reinf (mm2/m)
σi (mpa) slab 0.00 ‐0.07 ‐0.97 ‐9.13 6.66 ‐9.58 6.20 6.08 5.63
σi (mpa) girder ‐12.10 ‐13.10 ‐19.89 ‐27.08 ‐24.71 ‐30.47 ‐28.11 ‐16.10 ‐19.49
σb (mpa) girder 12.10 15.75 40.59 20.01 14.58 32.43 27.00 20.96 33.39
σt (mpa) slab 0.00 ‐0.29 ‐1.98 4.01 ‐1.59 3.16 ‐2.43 ‐2.20 ‐3.04
Reinf (mm2/m)
σi (mpa) slab 0.00 ‐0.18 ‐1.20 ‐1.39 0.72 ‐1.90 0.21 0.10 ‐0.41
σi (mpa) girder ‐31.72 ‐34.39 ‐42.06 ‐43.46 ‐27.67 ‐47.29 ‐31.50 ‐19.70 ‐23.54
σb (mpa) girder 31.72 41.49 69.54 27.51 29.87 41.53 43.90 37.58 51.61
σt (mpa) slab 0.00 ‐0.54 ‐2.49 3.72 ‐1.71 2.75 ‐2.68 ‐2.36 ‐3.33
Reinf (mm2/m)
σi (mpa) slab 0.00 ‐0.36 ‐1.63 ‐1.65 0.65 ‐2.29 0.01 0.02 ‐0.62
σi (mpa) girder ‐44.19 ‐49.53 ‐59.09 ‐59.27 ‐41.97 ‐64.06 ‐46.75 ‐34.29 ‐39.07
σb (mpa) girder 44.19 59.00 85.53 41.33 47.26 54.60 60.53 56.75 70.02
σt (mpa) slab 0.00 ‐0.84 ‐2.89 3.57 ‐1.94 2.55 ‐2.97 ‐2.66 ‐3.69
Reinf (mm2/m)
σi (mpa) slab 0.00 ‐0.55 ‐1.91 ‐1.76 0.50 ‐2.44 ‐0.18 ‐0.18 ‐0.86
σi (mpa) girder ‐66.55 ‐74.86 ‐85.00 ‐83.90 ‐66.96 ‐88.97 ‐72.04 ‐59.99 ‐65.06
σb (mpa) girder 66.55 89.25 116.96 69.12 76.85 82.97 90.70 87.73 101.59
σt (mpa) slab 0.00 ‐0.49 ‐1.68 3.93 ‐1.59 3.33 ‐2.19 ‐2.31 ‐2.91
Reinf (mm2/m)
σi (mpa) slab 0.00 ‐0.32 ‐1.11 ‐1.53 0.73 ‐1.92 0.34 0.05 ‐0.34
σi (mpa) girder ‐39.88 ‐44.73 ‐50.60 ‐53.77 ‐36.83 ‐56.71 ‐39.77 ‐29.86 ‐32.79
σb (mpa) girder 39.88 53.12 69.15 32.98 40.71 41.00 48.73 51.60 59.61
σt (mpa) slab 0.00 ‐0.18 ‐1.07 4.23 ‐1.29 3.79 ‐1.73 ‐2.00 ‐2.45
Reinf (mm2/m)
σi (mpa) slab 0.00 ‐0.11 ‐0.65 ‐1.32 0.94 ‐1.59 0.67 0.26 ‐0.01
σi (mpa) girder ‐20.86 ‐22.53 ‐26.58 ‐31.57 ‐14.63 ‐33.60 ‐16.66 ‐7.66 ‐9.69
Page 69 of 156
σb (mpa) girder 20.86 26.88 41.47 6.74 14.48 14.04 21.77 25.36 32.66
σt (mpa) slab 0.00 0.06 1.36 4.48 ‐1.04 5.13 ‐0.39 ‐1.76 ‐1.11
Reinf (mm2/m)
σi (mpa) slab 0.00 0.04 0.83 ‐1.17 1.09 ‐0.77 1.49 0.41 0.80
σi (mpa) girder 4.25 4.80 10.75 ‐4.24 12.69 ‐1.27 15.67 19.67 22.64
σb (mpa) girder ‐4.25 ‐6.23 ‐27.69 ‐26.37 ‐18.64 ‐37.10 ‐29.36 ‐7.75 ‐18.48
σt (mpa) slab 0.00 0.21 1.71 4.63 ‐0.89 5.38 ‐0.14 ‐1.61 ‐0.86
Reinf (mm2/m)
σi (mpa) slab 0.00 0.13 1.04 ‐1.08 1.18 ‐0.62 1.64 0.50 0.95
σi (mpa) girder 19.56 21.49 28.30 12.45 29.39 15.85 32.79 36.36 39.76
σb (mpa) girder ‐19.56 ‐26.61 ‐51.45 ‐46.75 ‐39.02 ‐59.17 ‐51.44 ‐28.13 ‐40.55
σt (mpa) slab 0.00 0.34 2.17 4.76 ‐0.76 5.67 0.15 ‐1.48 ‐0.57
Reinf (mm2/m)
σi (mpa) slab 0.00 0.21 1.32 ‐1.00 1.26 ‐0.44 1.81 0.58 1.13
σi (mpa) girder 32.00 35.09 43.43 26.05 42.99 30.21 47.15 49.96 54.13
σb (mpa) girder ‐32.00 ‐43.27 ‐73.67 ‐63.41 ‐55.68 ‐78.61 ‐70.87 ‐44.79 ‐59.99
σt (mpa) slab 0.00 0.45 2.63 4.86 ‐0.66 5.95 0.44 ‐1.37 ‐0.28
Reinf (mm2/m)
σi (mpa) slab 0.00 0.25 1.50 ‐0.95 1.31 ‐0.33 1.93 0.63 1.25
σi (mpa) girder 51.29 55.11 64.42 46.06 63.00 50.72 67.66 69.97 74.63
σb (mpa) girder ‐51.29 ‐68.30 ‐109.79 ‐88.44 ‐80.71 ‐109.18 ‐101.45 ‐69.82 ‐90.57
σt (mpa) slab 0.00 0.45 2.79 4.86 ‐0.66 6.03 0.52 ‐1.37 ‐0.20
Reinf (mm2/m)
σi (mpa) slab 0.00 0.26 1.63 ‐0.94 1.32 ‐0.26 2.00 0.63 1.32
σi (mpa) girder 45.78 49.72 60.01 40.68 57.61 45.82 62.76 64.59 69.73
σb (mpa) girder ‐45.78 ‐61.87 ‐103.89 ‐82.01 ‐74.27 ‐103.02 ‐95.28 ‐63.39 ‐84.40
σt (mpa) slab 0.00 0.47 2.81 4.88 ‐0.64 6.05 0.53 ‐1.36 ‐0.18
Reinf (mm2/m)
σi (mpa) slab 0.00 0.27 1.64 ‐0.93 1.33 ‐0.25 2.01 0.64 1.33
Page 70 of 156
σi (mpa) girder 47.46 51.56 61.84 42.51 59.45 47.66 64.59 66.42 71.57
σb (mpa) girder ‐47.46 ‐64.19 ‐106.21 ‐84.33 ‐76.59 ‐105.34 ‐97.60 ‐65.71 ‐86.72
Summary of Stresses in Outer Girder (Footpath Side)
C1 C2 C3 C4 C5 C6 C7 C8 C9
Description Section
σt (mpa) slab 0.00 0.11 0.43 3.71 ‐1.58 3.87 ‐1.42 ‐1.94 ‐1.78
Reinf (mm2/m)
σi (mpa) slab 0.00 0.07 0.27 ‐1.47 0.69 ‐1.37 0.79 0.22 0.32
σi (mpa) girder 6.73 7.74 9.24 ‐3.83 12.43 ‐3.08 13.19 22.55 23.30
σb (mpa) girder ‐6.73 ‐10.08 ‐15.07 ‐6.76 ‐17.33 ‐9.25 ‐19.82 ‐19.12 ‐21.62
σt (mpa) slab 0.00 0.20 0.85 3.94 ‐1.44 4.27 ‐1.11 ‐1.84 ‐1.52
Reinf (mm2/m)
σi (mpa) slab 0.00 0.12 0.53 ‐1.33 0.78 ‐1.12 0.98 0.28 0.48
σi (mpa) girder 12.67 14.52 17.57 3.64 19.44 5.16 20.96 29.12 30.65
σb (mpa) girder ‐12.67 ‐18.79 ‐28.91 ‐17.75 ‐26.78 ‐22.81 ‐31.84 ‐27.68 ‐32.74
σt (mpa) slab 0.00 0.23 1.18 4.12 ‐1.36 4.60 ‐0.88 ‐1.81 ‐1.33
Reinf (mm2/m)
σi (mpa) slab 0.00 0.14 0.74 ‐1.22 0.83 ‐0.92 1.13 0.30 0.60
σi (mpa) girder 15.31 17.45 21.93 7.26 22.59 9.49 24.83 31.84 34.08
σb (mpa) girder ‐15.31 ‐22.39 ‐37.24 ‐23.63 ‐31.13 ‐31.06 ‐38.55 ‐31.13 ‐38.55
σt (mpa) slab 0.00 0.20 1.44 4.24 ‐1.34 4.86 ‐0.72 ‐1.82 ‐1.20
Reinf (mm2/m)
σi (mpa) slab 0.00 0.13 0.90 ‐1.14 0.84 ‐0.75 1.23 0.28 0.67
σi (mpa) girder 14.65 16.55 22.37 7.04 21.91 9.95 24.82 30.73 33.64
σb (mpa) girder ‐14.65 ‐20.94 ‐40.24 ‐24.45 ‐30.41 ‐34.10 ‐40.06 ‐29.51 ‐39.17
σt (mpa) slab 0.00 0.14 1.45 4.33 ‐1.35 4.98 ‐0.70 ‐1.88 ‐1.22
Reinf (mm2/m)
σi (mpa) slab 0.00 0.09 0.91 ‐1.09 0.83 ‐0.68 1.24 0.25 0.66
σi (mpa) girder 10.25 11.58 17.72 2.76 17.17 5.83 20.24 25.56 28.63
σb (mpa) girder ‐10.25 ‐14.64 ‐35.01 ‐20.44 ‐24.86 ‐30.62 ‐35.04 ‐23.07 ‐33.25
σt (mpa) slab 0.00 0.05 1.31 4.27 ‐1.37 4.90 ‐0.74 ‐1.91 ‐1.28
Page 71 of 156
Reinf (mm2/m)
σi (mpa) slab 0.00 0.03 0.84 ‐1.16 0.84 ‐0.75 1.24 0.24 0.64
σi (mpa) girder 2.13 2.59 8.64 ‐6.32 8.65 ‐3.30 11.67 16.89 19.92
σb (mpa) girder ‐2.13 ‐3.55 ‐22.11 ‐12.21 ‐14.20 ‐21.49 ‐23.48 ‐11.36 ‐20.64
σt (mpa) slab 0.00 ‐0.11 1.00 4.16 ‐1.44 4.72 ‐0.88 ‐2.01 ‐1.45
Reinf (mm2/m)
σi (mpa) slab 0.00 ‐0.07 0.63 ‐1.27 0.81 ‐0.91 1.16 0.20 0.55
σi (mpa) girder ‐12.19 ‐13.25 ‐7.97 ‐22.22 ‐6.67 ‐19.58 ‐4.03 1.39 4.04
σb (mpa) girder 12.19 15.57 ‐1.24 3.95 4.49 ‐4.45 ‐3.91 8.41 0.00
σt (mpa) slab 0.00 ‐0.38 ‐2.24 3.88 ‐1.58 2.95 ‐2.51 ‐2.17 ‐3.10
Reinf (mm2/m)
σi (mpa) slab 0.00 ‐0.25 ‐1.48 ‐1.51 0.74 ‐2.13 0.12 0.12 ‐0.49
σi (mpa) girder ‐31.69 ‐35.46 ‐44.65 ‐44.93 ‐28.06 ‐49.53 ‐32.66 ‐20.04 ‐24.64
σb (mpa) girder 31.69 41.98 67.11 26.82 30.73 39.39 43.30 35.86 48.43
σt (mpa) slab 0.00 ‐0.65 ‐2.63 3.79 ‐1.79 2.81 ‐2.78 ‐2.43 ‐3.42
Reinf (mm2/m)
σi (mpa) slab 0.00 ‐0.44 ‐1.78 ‐1.58 0.58 ‐2.25 ‐0.08 ‐0.06 ‐0.73
σi (mpa) girder ‐43.97 ‐50.61 ‐60.66 ‐59.14 ‐42.91 ‐64.16 ‐47.93 ‐35.43 ‐40.45
σb (mpa) girder 43.97 60.09 84.45 42.57 48.07 54.76 60.26 54.13 66.31
σt (mpa) slab 0.00 ‐1.03 ‐2.86 3.59 ‐2.10 2.67 ‐3.01 ‐2.78 ‐3.70
Reinf (mm2/m)
σi (mpa) slab 0.00 ‐0.70 ‐1.94 ‐1.72 0.38 ‐2.34 ‐0.24 ‐0.30 ‐0.92
σi (mpa) girder ‐66.08 ‐76.58 ‐85.86 ‐84.26 ‐68.49 ‐88.90 ‐73.14 ‐61.53 ‐66.17
σb (mpa) girder 66.08 91.56 114.08 71.56 78.84 82.82 90.10 85.86 97.12
σt (mpa) slab 0.00 ‐0.59 ‐1.55 4.03 ‐1.66 3.55 ‐2.14 ‐2.34 ‐2.82
Reinf (mm2/m)
σi (mpa) slab 0.00 ‐0.40 ‐1.05 ‐1.42 0.68 ‐1.75 0.35 0.00 ‐0.33
σi (mpa) girder ‐39.64 ‐45.64 ‐50.53 ‐53.32 ‐37.55 ‐55.76 ‐40.00 ‐30.59 ‐33.03
σb (mpa) girder 39.64 54.20 66.07 34.20 41.48 40.13 47.41 48.50 54.43
Page 72 of 156
σt (mpa) slab 0.00 ‐0.22 ‐0.81 4.40 ‐1.28 4.11 ‐1.58 ‐1.97 ‐2.26
Reinf (mm2/m)
σi (mpa) slab 0.00 ‐0.14 ‐0.51 ‐1.16 0.94 ‐1.35 0.75 0.26 0.07
σi (mpa) girder ‐20.78 ‐22.84 ‐25.65 ‐30.52 ‐14.75 ‐31.92 ‐16.16 ‐7.79 ‐9.19
σb (mpa) girder 20.78 27.24 36.06 7.23 14.52 11.64 18.93 21.54 25.95
σt (mpa) slab 0.00 0.07 1.01 4.69 ‐1.00 5.16 ‐0.53 ‐1.68 ‐1.21
Reinf (mm2/m)
σi (mpa) slab 0.00 0.04 0.64 ‐0.98 1.12 ‐0.68 1.42 0.44 0.74
σi (mpa) girder 4.19 4.86 9.31 ‐2.82 12.95 ‐0.59 15.17 19.91 22.14
σb (mpa) girder ‐4.19 ‐6.29 ‐20.26 ‐26.30 ‐19.01 ‐33.28 ‐25.99 ‐11.99 ‐18.97
σt (mpa) slab 0.00 0.25 1.53 4.87 ‐0.82 5.51 ‐0.18 ‐1.50 ‐0.86
Reinf (mm2/m)
σi (mpa) slab 0.00 0.16 0.97 ‐0.87 1.23 ‐0.46 1.64 0.55 0.96
σi (mpa) girder 19.49 21.83 27.93 14.15 29.91 17.20 32.97 36.88 39.93
σb (mpa) girder ‐19.49 ‐26.91 ‐46.32 ‐46.92 ‐39.63 ‐56.62 ‐49.33 ‐32.61 ‐42.31
σt (mpa) slab 0.00 0.40 2.06 5.02 ‐0.67 5.85 0.16 ‐1.35 ‐0.52
Reinf (mm2/m)
σi (mpa) slab 0.00 0.25 1.30 ‐0.77 1.33 ‐0.25 1.86 0.65 1.17
σi (mpa) girder 31.95 35.71 43.62 28.03 43.80 31.99 47.75 50.76 54.72
σb (mpa) girder ‐31.95 ‐43.90 ‐69.02 ‐63.91 ‐56.62 ‐76.47 ‐69.18 ‐49.60 ‐62.16
σt (mpa) slab 0.00 0.54 2.46 5.16 ‐0.53 6.12 0.43 ‐1.21 ‐0.25
Reinf (mm2/m)
σi (mpa) slab 0.00 0.32 1.47 ‐0.70 1.40 ‐0.13 1.98 0.72 1.29
σi (mpa) girder 51.21 56.05 64.68 48.37 64.13 52.69 68.45 71.10 75.42
σb (mpa) girder ‐51.21 ‐69.68 ‐102.65 ‐89.68 ‐82.40 ‐106.17 ‐98.88 ‐75.38 ‐91.86
σt (mpa) slab 0.00 0.58 2.28 5.20 ‐0.49 6.05 0.36 ‐1.17 ‐0.32
Reinf (mm2/m)
σi (mpa) slab 0.00 0.36 1.42 ‐0.66 1.44 ‐0.13 1.97 0.76 1.29
σi (mpa) girder 45.63 51.02 58.99 43.34 59.10 47.33 63.09 66.07 70.06
σb (mpa) girder ‐45.63 ‐63.69 ‐90.43 ‐83.69 ‐76.41 ‐97.06 ‐89.78 ‐69.39 ‐82.76
Page 73 of 156
σt (mpa) slab 0.00 0.58 1.96 5.20 ‐0.49 5.89 0.20 ‐1.17 ‐0.48
Reinf (mm2/m)
σi (mpa) slab 0.00 0.36 1.21 ‐0.67 1.43 ‐0.24 1.86 0.75 1.18
σi (mpa) girder 47.28 52.62 58.99 44.95 60.71 48.13 63.89 67.68 70.86
σb (mpa) girder ‐47.28 ‐66.14 ‐88.62 ‐86.14 ‐78.86 ‐97.38 ‐90.10 ‐71.84 ‐83.08
STRESSES INCL. EFFECT OF DIFFERENTIAL SETTLEMENT AND PRESTRESS

OUTER GIRDER stress section St diff set p/a p.e/z total
maximum stress at top of slab ‐3.8 11 ‐0.58 0.15 0.65 ‐3.55
maximum stress at bottom of slab ‐1.0 11 ‐0.42 0.15 0.47 ‐0.77
max tension at top of girder ‐86.5 11 ‐6.36 2.28 7.05 ‐83.57
max comp at bottom of girder 115.7 11 10.69 2.28 ‐11.86 116.84
max comp at top of girder 67.7 17 1.98 ‐1.44 ‐3.34 64.86
max tension at bottom of girder ‐114.0 17 ‐4.53 ‐1.44 7.65 ‐112.37
SEC Ax F Mom
11 406
BM DUE TO DIF SET
17 148
11 159 ‐450
AX F AND BM DUE TO PRESTRESS
17 ‐102 250 621 386 ‐3.55
200 ‐1.33
Tensile F ‐523554.4 N 50
Tensile Force in two outer girders ‐1047109 N ‐0.77
INNER GIRDER
stress section St diff set p/a p.e/z total
maximum stress at top of slab ‐3.7 11 ‐0.58 0.10 0.39 ‐3.78
maximum stress at bottom of slab ‐0.9 11 ‐0.42 0.10 0.28 ‐0.90
max tension at top of girder ‐85.0 11 ‐6.84 1.43 4.23 ‐86.18
max comp at bottom of girder 117.0 11 11.32 1.43 7.70 137.41
max comp at top of girder 64.4 17 1.81 0.86 2.50 69.59
max tension at bottom of girder ‐109.8 17 ‐4.59 0.86 ‐6.37 ‐119.89
SEC Ax F Mom
11 436
BM DUE TO DIF SET
17 153
11 104 ‐297
AX F AND BM DUE TO PRESTRESS
17 64 212 480 774 ‐3.78
200 ‐1.47
Tensile F ‐686724 N 50
Tensile Force in four inner girders ‐2746898 N ‐0.90
Total tensile force ‐3794006 N
Total reinf required ‐3794006/240 15808 sqmm Permissible flexural tensile strength in concrete
i.e. 20 diameter 51 bars =0.7*SQRT(50) 4.950 >3.78
Ref clause 603.1 of IRC:22‐2008
As structure is safe with and without all the STAY cables, it will be safe with one cable snaped case also.
SHEAR CHECK DL 376
SDL 167
Page 74 of 156
LL 404
TTL 947 KN
SHEAR STRESS 38.65 mpa permissible 95 mpa
7.4 Design of end block

Type of cable 4K15
UTS 1040 kN
Variation in cable forces due to different loads Load median side ftp side
SIDL 0.52 0.81 tension
LL 1.58 1.12 tension
DF Set 0.69 0.69 revesible
Diff Shrink 0.04 0.04 tension
Temp Gr 0.09 0.09 revesible
2.92 2.75
Jacking force (15%) 156 kN
Maximum force after friction and slip 126 kN
Increaase force due to diff settlement etc 134 kN
Adopted force for anchorage design 156 kN
Moment in main plate 156*0.156/4 6.084 kNm

Section modulus of the plate 216000 mm^3/m 156
Stress in plate 6.084*1e6/216000 28.167 mpa
Well within permissible limits 36 th plate
Longitudinal shear per unit length 156/2 78.0 kn/M
8 mm fillet weld would suffice. 0.7*8*108*1000*4 2419.2 kN/m
(two sides of each stiffner)
Capacity of 200 long plate 484 KN >> 156 OK
7.5 FRICTION AND SLIP LOSS

Friction losses would only take place over the pylon where the cable passes through saddle and deviates also for 53 degrees.
53 deg
indicative cable profile

Change in angle (assuming one end stressing) 53 deg = 0.925 radians
Length of the cable through pylon 2 m
Coefficient of friction μ 0.17 Refer table 7.1 of IRC 112‐2011
Wobble Coefficient k 0.002 Refer table 7.1 of IRC 112‐2012
e‐(μθ+kx) 0.851
Cable 1
UTS of 4K15 104 t, area cable 0.00056 sqm
Page 75 of 156
jacking Force as fraction of UTS 0.13
Jacking Force 104*0.13 13.52 t, E value 1.95E+07 t/sqm
Half length of cable 16.6886 m

Slip 6 mm
Half area of Slip F. diag 32.76 T
F= 13.52
16.689 m F= 11.51
F' = 11.53
F after silp 11.56
F after silp 9.54
Force diagram after friction and slip
Average force in cable before slip 12.51 t
Extension at stressing end 38.6 mm
Cable 2

Slip 6 mm
F= 13.52
13.89 m F= 11.51
F' = 11.33
F after silp 11.16
F after silp 9.15
Cable 3

Slip 6 mm
F= 15.6
11.1 m F= 13.28
F' = 12.96
F after silp 12.65
F after silp 10.32
Page 76 of 156
Cable 4

Slip 6 mm
F= 15.6
8.3 m F= 13.28
F' = 12.46
F after silp 11.65
F after silp 9.33
Page 77 of 156
8 DESIGN OF SHEAR CONNECTOR ‐ OUTER GIRDER SUPPORT SECTION
Following two cases have been considered.
1 Fatigue due to repeated loading
2 Ultimate flexural strength
VL = (V Ac Y) / I
Where V= Vertical Shear
Ac = Transformed compression area of concrete above NA of composite section.
Y= Distance from neutral axis of composite section to centroid of Ac under consideration
For Permanent Loading

Ac = 0.0155 m2
I = 0.0428 m4
Y = 0.8068 m
Ac.Y/I = 0.2919 m‐1
For Transient Loading

Ac = 0.031 m2
I = 0.05113 m4
Y = 0.661 m
Ac.Y/I = 0.4008 m‐1
Load Case Vertical Shear (kN)

Permanent Loading Load Fac
SIDL 128 kN 1.75
Transient Loading
LL (Max) 268 kN 1.5
LL (Min)
ULTIMATE LIMIT STATE CRITERIA
Long. shear due to SDL 127.7*1.75*0.2919 65.2 kN/m
Long. shear due to LL 268*1.5*0.4008 161.1 kN/m
Total Long. Shear 226.4 kN/m
spacing 'p' = ΣQu/VL (Refer cl 606.4.1 of IRC 22)

Qu for one connector = 99 kN (refer Table 7)
Qu for three connector 3*99= 297 kN
spacing 'p' 297/226.4 1.31 m
Page 78 of 156
FLEXURAL STRENGTH CRITERIA
H1 (cl 606.4.1.1) = Asl. Fy. 10‐3/γm = 785 kN
Asl = 1570 mm2 (10@150 at top and bottom)
Fy = 500
‐3
H2 (cl 606.4.1.1) = 6 Acc. fck. 10 = 4185.11 kN
2
Acc = 232506 mm
fck = 50 mpa
Qu = 99 kN (for 20 dia and 110mm long studs)
spacing 7.56688 m
Dist between max moment and zero moment point 20 m
LIMIT STATE (SLS) OF FATIGUE CRITERIA
Long. shear due to LL, Vr 107.4 kN/m 161.12/1.5

Qr 17 (table 8)
spacing 'p' = ΣQr/VL (Refer cl 606.4.2 of IRC 22)
=3*17/107.41 0.475 m
TRANSVERSE SHEAR CHECK (cl 606.10)
1 VL allowed 0.632 L SQRT(fck)

L= 800 mm
fck= 50 mpa
VL allowed 3575.13 kN/m
2 VL allowed 0.232 L SQRT(fck) + 0.1 Ast. Fst. N
2
Ast 523.599 mm n= 1
fst 500 mpa
VL = 226.4 kN/m less than both 1 & 2.
Min trans reinf 1.13 cm2/m
113.20 sqmm/m
DESIGN OF SHEAR CONNECTOR ‐ OUTER GIRDER AT L/8 SECTION

SIDL 76 1.75
Transient Loading
LL (Max) 255 1.5
LL (Min)
Page 79 of 156

spacing 'p' 297/192.08 1.55 m

‐3
H1 (cl 606.4.1.1) = Asl. Fy. 10 /γm = 785 kN
Asl = 1570 mm2 (10@150 at top and bottom)
Fy = 500
H2 (cl 606.4.1.1) = 6 Acc. fck. 10‐3 = 4185.11 kN
2
Acc = 232506 mm
fck = 50 mpa
spacing 7.56688 m

Qr 17 (table 8)
=3*17/102.2 0.499 m

L= 800 mm
fck= 50 mpa
2
Ast 523.599 mm n= 1
fst 500 mpa
96.04 sqmm/m
Page 80 of 156
DESIGN OF SHEAR CONNECTOR ‐ INNER GIRDER SUPPORT SECTION
Following two cases have been considered.
1 Fatigue due to repeated loading
2 Ultimate flexural strength
VL = (V Ac Y) / I
Where V= Vertical Shear
Ac = Transformed compression area of concrete above NA of composite section.
Y= Distance from neutral axis to centroid of concrete
For Permanent Loading

Ac = 0.0183 m2
I = 0.0448 m4
Y = 0.7777 m
Ac.Y/I = 0.3182 m‐1
For Transient Loading

Ac = 0.03663 m2
I = 0.05369 m4
Y = 0.62144 m
Ac.Y/I = 0.4239 m‐1

SIDL 167 1.75
Transient Loading
LL (Max) 404 1.5
LL (Min)

spacing 'p' 297/349.598925 0.85 m
Page 81 of 156
H1 (cl 606.4.1.1) = Asl. Fy. 10‐3/γm = 2502 kN
Asl = 5003 mm2 (20@150 at top )
Fy = 500
‐3
H2 (cl 606.4.1.1) = 6 Acc. fck. 10 = 4944.61 kN
2
Acc = 274701 mm
fck = 50 mpa
spacing 2.37454 m

Qr 17 (table 8)
=3*17/171.26 0.298 m

L= 800 mm
fck= 50 mpa
2
Ast 523.599 mm n= 1
fst 500 mpa
174.80 sqmm/m
Page 82 of 156
9 FLEXURE CHECK FOR CROSS GIRDERS
9.1 SUMMARY OF SECTION PROPERTIES
End cross girder interm cross girder

Item Con. Stg Tr. Ld Per Ld Con. Stg Tr. Ld Per Ld
Tf (C Flange) 12 12 12 12 12 12
A 0.03 0.04 0.03 0.03 0.03 0.03
Ix‐x 0.01 0.02 0.01 0.01 0.01 0.01
Iy‐y 0.00 0.00 0.00 0.00 0.00 0.00
yi 0.75 0.39 0.53 0.75 0.75 0.75
yb 0.75 1.11 0.97 0.75 0.75 0.75
Zt ‐ 0.02 0.02 ‐ ‐ ‐
Ztg 0.01 0.04 0.02 0.01 0.01 0.01
Zb 0.01 0.01 0.01 0.01 0.01 0.01
Allowable tension in bending = 155 mpa

= 155000 kN/sqm
9.2 CONSTRUCTION STAGE CHECK
Girder alone for self wt and weight of deck slab.
End Cross Girder
lxx 2.24 m
rxx 0.54883
ryy 0.05738
rmin 0.05738
c1 750 mm
c2 750 mm
D 1500 mm
T 12 mm
l 2240 mm
rmin 57.4 mm
k1= 1 for ψ = 1 (Refer Table 8.3 of IRC 24)
k2= 0 for ω = 0.5 (Refer Table 8.4 of IRC 24)
Y= 26.5x1e5/(2240/57.4)^2 = 1740 mpa
X= 1740*SQRT(1+(1/20)*(2240*12/(57.4*1500))^2) = 1744 mpa
fcb= 1*(1744+0*1740)(750/750) = 1744 mpa
allowable stress in bending comp (cl 508.6, table 8.2 of IRC24) 158.0 mpa
Basic permissible stress in bending comp (cl 508.6.1 & Table 6.2) 155 mpa
Basic permissible stress in bending comp to be adopted 155 mpa
Page 83 of 156
Composite Cross Girders
During service stage compression flange is restrained by deck slab all along, hence effective
length of member is zero (refer cl 508.4.5 of IRC 24‐2001. This will give slenderness ratio as
infinite and basic permissible stress in compression shall be same as that in tension i.e. 155
mpa
9.3 SECTION CHECK FOR CONSTRUCTION & SERVICE STAGE
Compressive stress +ve Tensile stress ‐ve
Sagging BM ‐ve Hogging BM +ve
Summary of Stresses
COMP‐X GDR NON‐COMP X GDR
Description Section DL SIDL CWLL DL SIDL CWLL
V (kN) 4 19 136 5 21 141
M(kNm) 6 3 50 8 64 383
Max Hogging
σt (mpa) slab 0.00 ‐0.01 ‐0.27

σi (mpa) slab 0.00 ‐0.01 ‐0.16
σi (mpa) girder ‐0.57 ‐0.13 ‐1.23 ‐0.76 ‐6.10 ‐36.52
σb (mpa) girder 0.57 0.25 3.43 0.76 6.10 36.52
M(kNm) 6 3 50 8.0 64.0 383.0
Max Sagging
σt (mpa) slab 0.00 ‐0.01 ‐0.27

σi (mpa) slab 0.00 ‐0.01 ‐0.16
σi (mpa) girder ‐0.57 ‐0.13 ‐1.23 ‐0.76 ‐6.10 ‐36.52
σb (mpa) girder 0.57 0.25 3.43 0.76 6.10 36.52
Maximum bending moments and shear force out of all 4 composite girders are
considered for composite x girder at supports and maximum BM & SH out of 16 non
composite cross girders along the line of anchorage of extradose cable is considered
for designing the non-composite X Girders.
Bending tension in steel Girder = 155 mpa
Bending compr in End X Girder = 155 mpa
Bending compr in Inner X Girder = 155 mpa
Bending compr in Concrete = 16.6667 mpa
Summary of Stresses
End Cross Girder Interm Cross Girder 1
Comb 1 Comb 2 Comb 3 Comb 1 Comb 2 Comb 3
Description Section DL DL+SDL C2+LL DL DL+SDL C2+LL
σt (mpa) slab 0.00 ‐0.01 ‐0.28
Status OK OK OK
Reinf (mm2/m) 14 283
Max Hogging
σi (mpa) slab 0.00 ‐0.01 ‐0.17

Status OK OK OK
σi (mpa) girder ‐0.57 ‐0.71 ‐1.93 ‐0.76 ‐6.87 ‐43.39
Page 84 of 156
M
Status OK OK OK OK OK OK
σb (mpa) girder 0.57 0.82 4.25 0.76 6.87 43.39
σt (mpa) slab 0.00 ‐0.01 ‐0.28
Status OK OK OK
2
Reinf (mm /m)
Max Sagging
σi (mpa) slab 0.00 ‐0.01 ‐0.17
Status OK OK OK
si (mpa) girder ‐0.57 ‐0.71 ‐1.93 ‐0.76 ‐6.87 ‐43.39
sb (mpa) girder 0.57 0.82 4.25 0.76 6.87 43.39
Max shear force

end X Girder 159 kN
Shear Stress 8.96 mpa
< 95 mpa OK
Interm X Girder 167 kN
Shear Stress 9.4 mpa
< 95 mpa OK
Page 85 of 156
10 DESIGN OF WEB AND FLANGE SPLICE
10.1 DESIGN OF WEB AND FLANGE SPLICE
10.1.1 OUTER GIRDER (1st SPLICE)

web height = 1.75 Web thickness = 0.014
BM due to DL = 836.0 KNM Iw = 0.0063
BM due to SDL = 214.4 KNM Igirder alone = 0.024
BM due to LL = 1147.7 KNM Icomp (P) = 0.038
2198.1 KNM Icomp (T) = 0.047
SF due to DL = 227.8 KN
SF due to SDL = 81.0 KN
SF due to LL = 115.5 KN
424.0 KN
BM Contribution of the Web

Mw = (Iw/I)*M
= 409 kNm
(836*0.0063/0.024+214.4*0.0063/0.038+1147.7*0.0063/0.047)
Try M24 Bolts
R (as per IS 4000) = (Slip Factor*No fo eff interfaces*Min. Tension)/FOS
slip factor = 0.35 (Cl 5.4.1 of IS 4000)
No of eff. Interface = 2
Min bolt tension = 212 (Refer table 3 of IS 4000 for gr 8.8)
R = (0.35*2*212/1.4)
= 106 kN
No of bolts reqd. = SQRT(6*Mw/(m.p.R))
m no of lines of bolts = 3
p pitch = 65 > (2.5*24)
e (edge dist) = 40 > (1.5*24)
No of bolts reqd. = 11
say 24
Length of Plate 'ds' reqd = 2e+(n‐1)p
= 1575 mm
Min thickness of splice plate = tw * dw / (2 ds2)
2
tw= 14
= 8.64 mm dw= 1750
say 10 mm
Page 86 of 156
Check for Stresses in Bolts
Moment about cg of bolt group 409 + 424*(40+65*(3‐1)/2)/1000
453 kNm
747.5
40 65 65
F = M.r/ Σr2
Σr
2
= Σx2 + Σy2
Σx2 = 2 x 24 x 65
2
= 202800
Σy 2
= 2*3*747.5^2 = 3352538
+ 2*3*682.5^2 + 2794838
+ 2*3*617.5^2 + 2287838
+ 2*3*552.5^2 + 1831538
+ 2*3*487.5^2 + 1425938
+ 2*3*422.5^2 + 1071038
+ 2*3*357.5^2 + 766837.5
+ 2*3*292.5^2 + 513337.5
+ 2*3*227.5^2 + 310537.5
+ 2*3*162.5^2 + 158437.5
+ 2*3*97.5^2 + 57037.5
+ 2*3*32.5^2 + 6337.5
+ 1.46E+07
Σr 2
= 202800 + 1.46E+07 = 1.48E+07
ymax = 747.5 mm
xmax 65 mm
xresultant 750
Page 87 of 156
Cos(θ) 65/750 0.087
Fr 453*1e3*750/14779050 23.00 kN
Fv = 424/24/3 5.90 kN
FR = (23^2+5.9^2+2*23*5.9*0.087)^0.5 24.2 kN
< 106 kN
Check as Bearing type Joints
Shear in bolt at each interface 24.2/2 12.1 kN
Allowable value (Ref Table 2 of IS:4000) 73.2 kN OK
Bearing stress in web plate 72.0 mpa
permissible bearing stress 0.8 * 250 200.0 mpa OK
DESIGN OF TOP FLANGE SPLICE

nR= V*A*y*Length of splice plate M*y*Area of Plate to be spliced
+
I I
Overall depth of girder including deck slab 2.05 m
Thickness of top flange plate 25 mm
yt girder alone 0.900 m
yt permanent load 0.800 m
yt transient load 0.627 m
total deck slab thickness over girder 0.25 m
area of deck slab = 0.048 For Transient Loading
= 0.024 for permanent Loading
Eccentricity 'e' from deck slab top = 0.117 m, from top of deck slab
area of Top Plate to be spliced = 0.0150 sqm
Required area of splice plate (5% extra) = 0.0158 0.015*1.05
Total width of splice plate = 1080 mm (560 abv & 2 of 260 below
Thickness of plate required = 14.6 mm
say 16 mm
Length of splice plate on one side = 170 mm= 0.17 m
Area of top plate and deck for Perm load = 0.039 sqm
y from top = (0.024*0.1167+0.015*(0.25+0.0125))/0.039)
= 0.173 m
Area of top plate and deck for Trans. load = 0.0630 sqm
y from top = (0.048*0.1167+0.015*(0.25+0.0125))/0.063)
= 0.151 m
Computiona of Longitudinal Force in top flange
Page 88 of 156
Loading Shear Bending y (shear) y(b'ding) A (top fl) I of section
DL 227.8 836.0 0.900 0.888 0.0150 0.024
SDL 81.0 214.4 0.627 0.538 0.039 0.038
LL 115.5 1147.7 0.476 0.365 0.0630 0.047
Force due to Long shear per unit length =227.825*0.015*0.9/0.024+81*0.039*0.627/0.038+115.50374331
5508*0.063*0.476/0.047
= 254.00 kN/m
Force due to Long shear in 0.17 m length =0.17*254= 43.18 kN
Force due to comp stress in bending =0.015*(836*0.888/0.024+214.4*0.538/0.038+1147.7*0.365/0.04
7
= 643 kN
Total comp. force = 686 kN
no of bolts required = 686/106= 6.47
provide 2x6 12 bolts
Shear in bolt at each interface 686/12/2 28.6 kN
DESIGN OF BOTTOM FLANGE SPLICE

Area of bottom plate = 0.015 sqm
area reqd for splice plate = 0.016 sqm =0.015*1.05
Total width of splice pl (abv & below) = 1030 mm 550+2*240
say 16.0 mm
Computiona of Longitudinal Force in Bottom flange
Loading Shear Bending y (shear) y(b'ding) A (bot fl) I of sect. Bot fl th. yb
DL 227.8 836.0 0.888 0.888 0.015 0.024 0.025 0.900
SDL 81.0 214.4 1.238 1.238 0.015 0.038 1.25
LL 115.5 1147.7 1.411 1.411 0.015 0.047 1.423
3315508*0.015*1.4105/0.047
= 218.00 kN/m
Force due to comp stress in bending =0.015*(836*0.888/0.024+214.4*1.2375/0.038+1147.7*1.4105/0.
Page 89 of 156
047
= 1085 kN
Total tensile force = 1145.00 kN
Check as Bearing type Joint
Bearing stress in bottom flange 79.5 mpa
10.1.2 OUTER GIRDER (2ND SPLICE)

BM due to DL = 548.0 KNM Iw = 0.0063
1247.0 KNM Icomp (T) = 0.046
616.0 KN

Mw = (Iw/I)*M
= 244 kNm
(548*0.0063/0.024+137*0.0063/0.038+562*0.0063/0.046)
Try M24 Bolts
R = (0.35*2*212/1.4)
= 106 kN
p pitch = 65 > (2.5*24)
Page 90 of 156
e (edge dist) = 40 > (1.5*24)
say 24
= 1575 mm
2
tw= 14
= 8.64 mm dw= 1750
say 10 mm

308 kNm
747.5
40 65 65
F = M.r/ Σr2
Σr
2
= Σx2 + Σy2
Σx
2 2
= 2 x 24 x 65
= 202800
Σy 2
= 2*3*747.5^2 = 3352538
+ 2*3*682.5^2 + 2794838
+ 2*3*617.5^2 + 2287838
+ 2*3*552.5^2 + 1831538
+ 2*3*487.5^2 + 1425938
+ 2*3*422.5^2 + 1071038
+ 2*3*357.5^2 + 766837.5
+ 2*3*292.5^2 + 513337.5
+ 2*3*227.5^2 + 310537.5
Page 91 of 156
+ 2*3*162.5^2 + 158437.5
+ 2*3*97.5^2 + 57037.5
+ 2*3*32.5^2 + 6337.5
1.46E+07
Σr 2
= 202800 + 1.46E+07 = 1.48E+07
ymax = 747.5 mm
xmax 65 mm
xresultant 750
Cos(θ) 65/750 0.087
Fr 308*1e3*750/14779050 15.60 kN
Fv = 616/24/3 8.60 kN
FR = (15.6^2+8.6^2+2*15.6*8.6*0.087)^0.5 18.5 kN
< 106 kN

+
I I
say 16 mm
Page 92 of 156
y from top = (0.0225*0.1148+0.015*(0.25+0.0125))/0.0375)
= 0.174 m
y from top = (0.045*0.1148+0.015*(0.25+0.0125))/0.06)
= 0.152 m

DL 285.3 548.0 0.900 0.888 0.0150 0.024
SDL 75.9 137.0 0.468 0.380 0.038 0.038
LL 254.7 562.0 0.283 0.173 0.0600 0.046
Force due to Long shear per unit length =285.3*0.015*0.9/0.024+75.9*0.0375*0.468/0.038+254.66792452
8302*0.06*0.283/0.046
= 289.50 kN/m
Force due to Long shear in 0.17 m length =0.17*289.5= 49.22 kN
Force due to comp stress in bending
=0.015*(548*0.888/0.024+137*0.38/0.038+562*0.173/0.046
= 356 kN

say 16.0 mm
Page 93 of 156
DL 285.3 548.0 0.8880 0.888 0.015 0.024 0.025 0.900
SDL 75.9 137.0 1.1905 1.191 0.015 0.038 1.203
LL 254.7 562.0 1.3565 1.357 0.015 0.046 1.369
528302*0.015*1.3565/0.046
= 306.70 kN/m
=0.015*(548*0.888/0.024+137*1.1905/0.038+562*1.3565/0.046
= 617 kN
10.1.3 OUTER GIRDER (3rd SPLICE)

BM due to DL = ‐1351.0 KNM Iw = 0.0063
BM due to SDL = ‐410.0 KNM Igirder alone = 0.024
BM due to LL = ‐1767.0 KNM Icomp (P) = 0.041
‐3528.0 KNM Icomp (T) = 0.049
236.0 KN

Mw = (Iw/I)*M
= 645 kNm
(‐1351*0.0063/0.024+‐410*0.0063/0.041+‐1767*0.0063/0.049)
Try M24 Bolts
Page 94 of 156
R = (0.35*2*212/1.4)
= 106 kN
p pitch = 65 > (2.5*24)
e (edge dist) = 40 > (1.5*24)
say 24
= 1575 mm
2
tw= 14
= 8.64 mm dw= 1750
say 10 mm

670 kNm
747.5
40 65 65
F = M.r/ Σr2
Σr2 = Σx2 + Σy2
Σx2 = 2 x 24 x 65
2
= 202800
Page 95 of 156
Σy2 = 2*3*747.5^2 = 3352538
+ 2*3*682.5^2 + 2794838
+ 2*3*617.5^2 + 2287838
+ 2*3*552.5^2 + 1831538
+ 2*3*487.5^2 + 1425938
+ 2*3*422.5^2 + 1071038
+ 2*3*357.5^2 + 766837.5
+ 2*3*292.5^2 + 513337.5
+ 2*3*227.5^2 + 310537.5
+ 2*3*162.5^2 + 158437.5
+ 2*3*97.5^2 + 57037.5
+ 2*3*32.5^2 + 6337.5
1.46E+07
Σr 2
= 202800 + 1.46E+07 = 1.48E+07
ymax = 747.5 mm
xmax 65 mm
xresultant 750
Cos(θ) 65/750 0.087
Fr 670*1e3*750/14779050 34.00 kN
Fv = 236/24/3 3.30 kN
FR = (34^2+3.3^2+2*34*3.3*0.087)^0.5 34.4 kN
< 106 kN

+
I I
Page 96 of 156
say 16 mm
y from top = (0.0215*0.1146+0.015*(0.25+0.0125))/0.0365)
= 0.175 m
y from top = (0.043*0.1146+0.015*(0.25+0.0125))/0.058)
= 0.153 m

DL 87.8 1351.0 0.900 0.888 0.0150 0.024
SDL 41.0 410.0 0.372 0.285 0.037 0.041
LL 106.8 1767.0 0.221 0.111 0.0580 0.049
906*0.058*0.221/0.049
= 90.90 kN/m
=0.015*(1351*0.888/0.024+410*0.285/0.041+1767*0.111/0.049
= 853 kN
Page 97 of 156
say 16.0 mm
DL 87.8 1351.0 0.8880 0.888 0.015 0.024 0.025 0.900
SDL 41.0 410.0 1.2055 1.206 0.015 0.041 1.218
LL 106.8 1767.0 1.3735 1.374 0.015 0.049 1.386
84906*0.015*1.3735/0.049
= 111.70 kN/m
Force due to comp stress in bending =0.015*(1351*0.888/0.024+410*1.2055/0.041+1767*1.3735/0.04
9
= 1674 kN
10.1.4 INNER GIRDER (3rd SPLICE)
BM due to DL = ‐1353.0 KNM Iw = 0.006
BM due to SDL = ‐599.0 KNM Igirder alone = 0.024
BM due to LL = ‐1460.0 KNM Icomp (P) = 0.043
‐3412.0 KNM Icomp (T) = 0.052
Page 98 of 156
411.0 KN

Mw = (Iw/I)*M
= 625.3 kNm
(‐1353*0.0063/0.0237+‐599*0.0063/0.043+‐1460*0.0063/0.0517)
Try 24 Bolts
R = 106 kN
p pitch = 65 > (2.5*24)
e (edge dist) = 40 > (1.5*24)
say 24
= 1575 mm
2
tw= 14
= 8.64 mm dw= 1750
say 10 mm
Moment about cg of bolt group = 625.3297 + 411*(40+130/2)/1000
= 668 kNm
747.5
40 130
M.r/ Σr
2
F =
Σr2 = Σx2 + Σy2
Σx
2 2
= 2 x 24 x 65
Page 99 of 156
= 202800
Σy 2
= 6*747.5^2 = 3352538
+ 6*682.5^2 + 2794838
+ 6*617.5^2 + 2287838
+ 6*552.5^2 + 1831538
+ 6*487.5^2 + 1425938
+ 6*422.5^2 + 1071038
+ 6*357.5^2 + 766837.5
+ 6*292.5^2 + 513337.5
+ 6*227.5^2 + 310537.5
+ 6*162.5^2 + 158437.5
+ 6*97.5^2 + 57037.5
+ 6*32.5^2 + 6337.5
1.46E+07
Σr 2
= 202800 + 1.46E+07 = 1.48E+07
ymax = 747.5 mm
xmax 65 mm
xresult 750
Cos(θ) 65/750.32 0.087
Fh 668*1e3*747.5/14779050 33.80 kN
Fv = 411/24/3 5.70 kN
FR = (33.8^2+5.7^2+2*33.8*5.7*0.087)^0.5 34.8 kN
< 106 kN
Bearing stress in web plate 104 mpa

V*A*y*Length of splice plate M*y*Area of Plate to be spliced
nR= +
I I
Page 100 of 156

Required area of splice plate = 0.0158 0.015*1.05
say 16 mm
Area of top plate and deck for P load = 0.01500 sqm
y from top = (0*0.1067+0.015*(0.25+0.0125))/0.015)
= 0.263 m
Area of top plate and deck for T load = 0.0150 sqm
y from top = (0*0.1067+0.015*(0.25+0.0125))/0.015)
= 0.263 m
DL 89.3 1353.0 0.900 0.888 0.015 0.0237
SDL 44.8 599.0 0.535 0.535 0.015 0.043
LL 276.7 1460.0 0.361 0.361 0.015 0.0517
8491*0.015*0.361/0.0517
= 88.20 kN/m
7
= 1025 kN
= 1040 kN
Bearing stress in plate 144.4 mpa
Page 101 of 156

say 16 mm
DL 89.3 1353.0 0.888 0.888 0.015 0.0237 0.025 0.9
SDL 44.8 599.0 1.215 1.215 0.015 0.043 1.227
LL 276.7 1460.0 1.385 1.385 0.015 0.0517 1.397
77358491*0.015*1.3845/0.0517
= 180.20 kN/m
Force due to comp stress in bending =0.015*(1353*0.8875/0.0237+599*1.2145/0.043+1460*1.3845/0.
0517
= 1600 kN
= 1650 kN
10.3 DESIGN OF CONNECTION OF INTERIM CROSS GIRDER WITH LONG GIRDER

BM due to DL = 8.0 KNM Iw = 0.003
455.0 KNM Icomp (T) = 0.008
Page 102 of 156

167.0 KN
Mw = (Iw/I)*M
= 187 kNm
(8*0.0032/0.008+64*0.0032/0.008+383*0.0032/0.008)
Try 24 Bolts
R = (0.35*2*212/1.4)
R = 106 kN
p pitch = 75 > (2.5*24)
e (edge dist) = 40 > (1.5*24)
say 17
= 1280 mm
2
tw= 12
= 7.98 mm dw= 1476
say 10 mm
= 200 kNm
600
40 75
Page 103 of 156

F = M.r/ Σr2
Σr2 = Σx2 + Σy2
Σx2 = 2 x 17 x 37.5
2
= 47812.5
Σy 2
= 4*600^2 = 1440000
+ 4*525^2 + 1102500
+ 4*450^2 + 810000
+ 4*375^2 + 562500
+ 4*300^2 + 360000
+ 4*225^2 + 202500
+ 4*150^2 + 90000
+ 4*75^2 + 22500
4.59E+06
Σr 2
= 47812.5 + 4.59E+06 = 4.64E+06
ymax = 600 mm
xmax 37.5 mm
xres 601.17 mm
Cos(θ) 37.5/601.17 0.062
Fh 200*1e3*600/4637812.5 25.90 kN
Fv = 167/17/2 4.90 kN
FR = (25.9^2+4.9^2+2*25.9*4.9*0.062)^0.5 26.7 kN
< 106 kN
Bearing stress in plate 93 mpa

+
I I
Overall depth of girder excluding deck slab 1.5 m
yt permanent load ‐ m
yt transient load ‐ m
Page 104 of 156

say 10 mm
y from top = (0*0.1+0.0042*(0.3+0.006))/0.0042)
= 0.306 m
y from top = (0*0.1+0.0042*(0.3+0.006))/0.0042)
= 0.306 m
DL 5.0 8.0 0.750 0.744 0.0042 0.008
SDL 21.0 64.0 0.750 0.744 0.0042 0.008
LL 141.0 383.0 0.750 0.744 0.0042 0.008
Force due to Long shear per unit length =5*0.0042*0.75/0.008+21*0.0042*0.75/0.008+141*0.0042*0.75/
0.008
= 65.80 kN/m
=0.0042*(8*0.744/0.008+64*0.744/0.008+383*0.744/0.008
= 178 kN
Total compressive force in top flange = 187 kN
provide 2*4 8 bolts
Page 105 of 156

Total width of splice pl (abv & below) = 560 mm (300 abv & 2 of 140 below
say 10 mm
DL 5.0 8.0 0.744 0.744 0.0042 0.008 0.012 0.75
SDL 21.0 64.0 0.744 0.744 0.0042 0.008 0.75
LL 141.0 383.0 0.744 0.744 0.0042 0.008 0.75
Force due to Long shear per unit length =5*0.0042*0.744/0.008+21*0.0042*0.744/0.008+141*0.0042*0.7

44/0.008
= 65.20 kN/m
= 178 kN
Total Tension in bottom flange = 187 kN
provide 2*4 8 bolts
10.3(a) DESIGN OF CONNECTION OF END CROSS GIRDER WITH LONG GIRDER

BM due to DL = 6.0 KNM Iw = 0.003
59.3 KNM Icomp (T) = 0.016
Page 106 of 156

159.0 KN
Mw = (Iw/I)*M
= 17 kNm
(6*0.0032/+3.3*0.0032/0.013+50*0.0032/0.016)
Try 24 Bolts
R = (0.35*2*212/1.4)
R = 106 kN
p pitch = 75 > (2.5*24)
e (edge dist) = 40 > (1.5*24)
say 13
= 980 mm
2
tw= 12
= 13.61 mm dw= 1476
say 16 mm
= 29 kNm
450
40 75
Page 107 of 156

F = M.r/ Σr2
Σr2 = Σx2 + Σy2
Σx2 = 2 x 13 x 37.5
2
= 36562.5
Σy 2
= 4*450^2 = 810000
+ 4*375^2 + 562500
+ 4*300^2 + 360000
+ 4*225^2 + 202500
+ 4*150^2 + 90000
+ 4*75^2 + 22500
2.05E+06
Σr 2
= 36562.5 + 2.05E+06 = 2.08E+06
ymax = 450 mm
xmax 37.5 mm
xres 451.56 mm
Cos(θ) 37.5/451.56 0.083
Fh 29*1e3*450/2084062.5 6.30 kN
Fv = 159/13/2 6.10 kN
FR = (6.3^2+6.1^2+2*6.3*6.1*0.083)^0.5 9.1 kN
< 106 kN
Bearing stress in plate 32 mpa

+
I I
Page 108 of 156

say 10 mm
y from top = (0.007*0.119+0.0042*(0.05+0.006))/0.0112)
= 0.095 m
y from top = (0.015*0.119+0.0042*(0.05+0.006))/0.0192)
= 0.105 m
DL 4.0 6.0 1.000 0.994 0.0042 0.003
SDL 18.8 3.3 0.778 1.000 0.0112 0.013
LL 135.9 50.0 0.645 0.589 0.0192 0.016
Force due to Long shear per unit length =4*0.0042*1/0.0032+18.8*0.0112*0.778/0.013+135.875*0.0192*
0.645/0.016
= 123.00 kN/m
=0.0042*(6*0.994/0.0032+3.3*1/0.013+50*0.589/0.016
= 17 kN
Total compressive force in top flange = 27 kN
provide 1*4 4 bolts

Page 109 of 156

Total width of splice pl (abv & below) = 560 mm (300 abv & 2 of 140 below
say 10 mm
DL 4.0 6.0 0.750 0.750 0.0042 0.003 0.0009 0.75
SDL 18.8 3.3 0.972 0.972 0.0042 0.013 0.972
LL 135.9 50.0 1.105 1.105 0.0042 0.016 1.105
Force due to Long shear per unit length =4*0.0042*0.75/0.0032+18.8*0.0042*0.972/0.013+135.875*0.004

2*1.105/0.016
= 49.30 kN/m
Force due to comp stress in bending =0.0042*(6*0.75/0.0032+3.3*0.972/0.013+50*1.105/0.016
= 21 kN
Total Tension in bottom flange = 28 kN
provide 2*4 8 bolts
10.5 DESIGN OF WEB STIFFNERS
d1 = 1750 mm tw = 14 mm
Minimum required web thickness for (IRC 3d>c>d 8.75 (d/200) Refer 509.6.1.1(b)i
24) .74d<c<d 8.75 (d/200) Refer 509.6.1.1(b)ii
ε=1 for grade 250 steel c<d 6.5 (d/270) Refer 509.6.1.1(b)iii
as per clause G4.11.2.2 of IRC 24

Min dist of stiffners 0.33d1 = 578 mm
Max dist of stiffners 1.5 d1 = 2625 mm
I1 = 1.5 x d1^3 x t^3/s^2 for S= 2625 mm
Page 110 of 156

I1 = 7.82E+05 Min t reqd 8.75 mm
Let us assume 12 mm x 144 mm single stiffners @ 2625 c/c on opposite
side alternatively
I provided (@web face) 12*144^3/3 1.19E+07 > 7.82E+05 hence OK
Mininimum required web thickness for 3d> c > d 8.75 (d/200) Refer 509.6.1.1(b)i
0.74d <c < d 8.8 (d/200) Refer 509.6.1.1(b)ii
c < 0.74d 6.5 (d/270) Refer 509.6.1.1(b)iii
10.6 DESIGN OF WEB STIFFNERS for END X GIRDER

d1 = 1476 mm tw = 0 mm
as per clause G4.11.2.2 of IRC 24
Min dist of stiffners 0.33d1 = 487 mm
I1 = 1.5 x d1^3 x t^3/s^2 for S= 2214 mm
I1 = 3.96E+05 Min t reqd 7.38 mm
Let us assume 10 mm x 120 mm single stiffners @ 2214 c/c on opposite
side alternatively
I provided (@web face) 10*120^3/3 5.76E+06 > 3.96E+05 ok
Mininimum required web thickness for 3d> c > d 7.38 (d/200) Refer 509.6.1.1(b)i
0.74d <c < d 7.38 (d/200) Refer 509.6.1.1(b)ii
c <d 5.47 (d/270) Refer 509.6.1.1(b)iii
BETWEEN BOTTOM FLANGE AND WEB
Longitudinal shear per unit length 180.2 kn/M
8 mm fillet weld would suffice. 0.7*8*108*1000*2 1209.6 kN/m
Page 111 of 156

11 DEFLECTION CHECK
SPAN 24.4 40
Allowable deflection for total load =span/600 40.7 66.7 mm
Allowable deflection for Live load =span/800 30.5 50.0 mm
DEFLECTION CHECK FOR OUTER GIRDER
Span 24.4 40
DL Deflection 1.0 24.6
SDL deflection 0.5 8.0
LL Deflection 6.0 20.4
Total 7.0 53.0
Hence, precamber is not required, however a precamber of 35mm is proposed for central span
Page 112 of 156

12 BEARING LOADS AND MOVEMENTS
Overall span 25 m No of FREE bearings 6
Effective span 24.4 m No of PIN brg at fixed end 1
Skew Angle 0 deg No of guided brgs at free end 1
Dist of ou'rmost brg from c/l of brg 5.6 m
Dist of inner brg from c/l of brg 3.36 m
Dist of inner most brg from c/l of brg 1.12 m
Σnx2 87.81 Zone factor (Zone IV) 0.24
c/c spacing between girders 2.24 m Importance factor 1.2
Deck cantilever 0.8 m R for brg 2
Depth of superstructure 2.05 m Sa/g 2.5
CG of DL from brg top 1.4228 m Hor seismic coeff 0.18
CG of SDL from brg top 2.23 m Vert seismic coeff 0.12
CG of LL from brg top 3.315 m Impact factor for Live Load 1.24
12.1 VERTICAL LOADS ON BEARINGS

MAX LIVE LOAD CASE
END SUPPORT
BRG LOCN
B1 B2 B3 B4 B5 B6
DL 140 150 150 150 150 140
SDL 70 40 40 50 70 90
70R(E)M 155 405 235 45 30 10
70R© 25 70 325 330 80 45
70R(E)F 15 40 200 385 175 65
2A(E) 180 220 185 110 40 20
2A© 5 110 200 205 125 25
MAX LL 180 405 325 385 175 65
TOTAL 390 595 515 585 395 295
MAX V ON OUTER BRGS 390 KN

MAX V ON INNER BRGS 595 KN
MIN LIVE LOAD CASE

END SUPPORT
BRG LOCN
B1 B2 B3 B4 B5 B6
DL 140 150 150 150 150 140
SDL 70 40 40 50 70 90
70R(E)M ‐65 ‐55 ‐40 ‐25 ‐10 10
70R© ‐30 ‐35 ‐30 ‐30 ‐35 ‐30
Page 113 of 156

70R(E)F ‐20 ‐25 ‐30 ‐35 ‐40 ‐40
2A(E) ‐60 ‐55 ‐40 ‐25 ‐15 5
2A© ‐35 ‐35 ‐35 ‐35 ‐35 ‐30
MIN LL ‐65 ‐55 ‐40 ‐35 ‐40 ‐40
TOTAL 145 135 150 165 180 190

MAX LIVE LOAD CASE

INTERNAL CONTINUOUS SUPPORT
BRG LOCN
B1 B2 B3 B4 B5 B6
DL 700 710 710 710 710 700
SDL 270 210 220 240 310 360
70R(E)M 190 595 355 70 70 75
70R© 10 65 525 540 125 95
70R(E)F 5 40 305 605 295 115
2A(E) 295 410 355 215 100 80
2A© 40 220 375 390 280 125
MAX LL 295 595 525 605 295 125
TOTAL 1265 1515 1455 1555 1315 1185

MIN LIVE LOAD CASE

INTERNAL CONTINUOUS SUPPORT
BRG LOCN
B1 B2 B3 B4 B5 B6
DL 700 710 710 710 710 700
SDL 270 210 220 240 310 360
70R(E)M ‐40 ‐30 ‐20 ‐15 ‐10 5
70R© ‐25 ‐20 ‐20 ‐20 ‐15 ‐15
70R(E)F ‐25 ‐15 ‐15 ‐20 ‐20 ‐20
2A(E) ‐25 ‐25 ‐20 ‐15 ‐10 ‐5
2A© ‐25 ‐20 ‐15 ‐15 ‐15 ‐15
MIN LL ‐40 ‐30 ‐20 ‐20 ‐20 ‐20
TOTAL 930 890 910 930 1000 1040
Page 114 of 156

12.2 HORIZONTAL LOADS
1. BREAKING AND BEARING FRICTION
CLASS 70R W (Two trains in 90m length) 2000 x 0.15 = 300
TOTAL FORCE 300
P143 P144 (F) P153 P154
MAX RXN DUE TO CL 70R 1000 0
DL RXN ON FREE PIERS 880 4240 4240 880
SDL RXN ON PIER 360 1610 1610 360
total 1240 5850 6850 1240
μ= 0.03 0.05
μR 242.7 404.5
μL 37.2 62 F (fixed) 306 kN for μ = 0.03
443 kN for μ = 0.05
2. SEISMIC LONGITUDINAL
SEISMIC ON DL 10240*0.18= 1843.2 KN
SEISMIC ON SDL 3940*0.18= 709.2 KN
SEISMIC ON 20% LL (zero in long dir but 20% braking) 60 KN
TOTAL FORCE 2612.4 KN
force per brg ( 1 Nos.) 2612.4 KN
End Support B1 B2 B3 B4 B5 B6
DL 140 150 150 150 150 140
SDL 70 40 40 50 70 90
20% LL MAX 36 81 65 77 35 13
20% LL MIN ‐13 ‐11 ‐8 ‐7 ‐8 ‐8
MAX V 246 271 255 277 255 243
Min V 223 201 198 207 228 238
Continuous Support B1 B2 B3 B4 B5 B6
DL 700 710 710 710 710 700
SDL 270 210 220 240 310 360
20% LL MAX 59 119 105 121 59 25
20% LL MIN ‐8 ‐6 ‐4 ‐4 ‐4 ‐4
MAX V 1029 1039 1035 1071 1079 1085
Min V 978 926 934 954 1024 1064
Page 115 of 156

3. SEISMIC TRANSVERSE
end sup cont sup
SEISMIC ON DL 158.4 763.2 KN
MOMENT DUE TO THIS F 158.4*1.423 225.379 1086 KNM
SEISMIC ON SDL 64.8 289.8 KN
MOMENT DUE TO THIS F 64.8*2.23 144.50 646.25 KNM
SEISMIC ON 20% LL 1,000.0*0.2*0.18 36 36.00 KN
MOMENT DUE TO THIS F 36*3.315 119.34 119.34 knm
TOTAL FORCE 259.2 1089.0 KN
Moment 489 1852 knm
FORCE ON GUIDED BRG ( 1 brgs) 259 1089 KN
ADDL VERT LOAD ON OUTER BRG +/‐ 31.20 118.08 KN
ADDL VERT LOAD ON INNER BRG +/‐ 18.72 70.85 KN
ADDL VERT LOAD ON INNER MOST BRG 6.24 23.62 KN
LONG FORCE DUE TO BRAKING 20% OF NORMAL 0 60.00 KN
SEISMIC ON DL+SDL (30%) 0 765.72 KN
TOTAL EXTERNAL LOAD 0 825.72 KN
LONG FORCE on fixed BRG 825.72 KN
4. SEISMIC VERTICAL
OUTER BRG
SEISMIC ON DL (30%) +/‐ 5.04 25.20 KN
SEISMIC ON SDL (30%) +/‐ 2.52 9.72 KN
SEISMIC ON 20% LL (30%) +/‐ 1.30 2.12 KN
INNER BRG
SEISMIC ON DL (30%) +/‐ 5.40 25.56 KN
SEISMIC ON SDL (30%) +/‐ 1.80 8.64 KN
SEISMIC ON 20% LL (30%) +/‐ 2.77 4.36 KN
5. WIND LOAD
Basic wind speed 47 m/sec
av height 15 m
Pz 512.5 N/sqm
Vz at 15m ht for basic wind speed of 33 m/sec 29.2 m/sec
Vz at 15m ht for basic wind speed of 47 m/sec 29.2*47/33 41.588 m/sec
Adopt basic wind speed of 36 m/sec at deck level with live load
Pz at 15m ht for basic wind speed of 36 m/sec 512.5*(36/29.2)^2 779 N/sqm
Gust factor G 2
CD for girder depth 1.8 m and spacing of 2.24 2*(1+2.24/(20*1.8))= 2.12
Area A1 2.9 FT 779*2*2.12*2.9 9579 N/m
Page 116 of 156

Load at END SUPPORT 9579*25/2/10000 11.97 t
acting at 1.45 m abv bearings
Load at iNTERM SUPPORT 9579*65/2/10000 31.13 t
Wind on Live Load

A1 3-(0.85) 2.15 m
G 2.0
CD Refer cl 209.3.6 1.2
FT Pz. A1. G. CD =779*2.15*2*1.2 = 4020 N/rm
Load at end SUPPORT 4019.64*25/2/10000 5.02 t
Total moment due to Hor load 3.975*5.02+11.97*1.45 37.311 tm
Max vert load due to this moment on outer brg 2.38 t
Max vert load due to this moment on inner brg 1.43 t
Load at INTERM SUPPORT 4019.64*65/2/10000 13.06 t
Total moment due to Hor load 3.975*13.06+31.13*1.45 97.052 tm
Max vert load due to this moment on outer brg 6.19 t
Max vert load due to this moment on inner brg 3.71 t
Vert. Load Pz. A3. G. CL

where Pz 779.0 N/sqm
A3 12.00 m
G 2.0
CL 0.75
Fv 14022 N/rm
Fv 1.40 t/rm
Load at END SUPPORT 1.402*25/2 17.53 t
Load per brg 17.53/6 2.92 t
Load at INTERM SUPPORT 1.402*65/2 45.57 t
Load per brg 45.57/6 7.60 t
end sup Int. Supp
Total load due to wind on outer brg 5.30 13.78 t
Total load due to wind on inner brg 4.35 11.31 t
C. LONGITUDINAL MOVEMENT AT BRG/EXP JOINT
EFFECTIVE SPAN 24.4 64.4 40 M
RES. SHRINKAGE COEFF 0
COEFF OF THERMAL EXP 1.2E‐05 /DEG
Page 117 of 156

TEMP VARIATION 36.25 DEG
MOVEMENT DUE TO TEMP 11 28 17 MM
mOVEMENT DUE TO SHRINKAGE 0 0 MM
TOTAL CONTRACTION 11 28 17 MM
TOTAL EXPANSION 11 28 17 MM
Additional movement due to deflection of Pier (Refer STAAD output) 14.2 mm
TOTAL movement incl pier deflection 25 42 32 mm
Addl movem't due to deflection of Pier in seismic case (R=3 ) 55.9 mm
TOTAL movement incl pier deflection in seismic case 67 84 73 mm
TRANSVERSE MOVEMENT AT BRG/EXP JOINT
Dist of outer brg from pin/guided brg 5.6 M
COEFF OF THERMAL EXP 1.2E‐05 /DEG
TEMP VARIATION 40 DEG
MOVEMENT DUE TO TEMP 2.69 MM
MOVEMENT DUE TO TEMP in inner bearing 1.61 MM
MOVEMENT DUE TO TEMP in inner most bearing 0.54 MM
D. ROTATION
ROTATION IS SMALL, ASSUME 0.01 RAD
12.3 SUMMARY OF BEARING LOADS
END SUPport
1.0 NORMAL CASE
BEARING HOR LOAD MOVEMENT ROT.
V MAX V MIN PERM V
MARK LONG TRANS +VE ‐VE
Inner Brg 595 135 42 42 0.01
Outer Brg 390 145 42 42 0.01
Guided (B3) 42 42 0.01
2.0 SEISMIC LONGITUDINAL
V MAX V MIN PERM V
Inner Brg 287 188 84 84 0.01
Outer Brg 255 214 84 84 0.01
Guided (B3) 78 84 84 0.01
3.0 SEISMIC TRANSVERSE
V MAX V MIN PERM V
Inner Brg 306 169 42 42 0.01
Outer Brg 286 183 42 42 0.01
Guided (B3) 259 42 42 0.01
4 WIND
Page 118 of 156

V MAX V MIN PERM V
Inner Brg 638 92 42 42 0.01
Outer Brg 443 92 42 42 0.01
Guided (B3) 50 42 42 0.01
CONTINUOUS SUPPORT
1.0 NORMAL CASE
V MAX V MIN PERM V
MARK LONG TRANS +VE ‐VE rad
Inner Brg 1555 890 32 32 0.01
Outer Brg 1265 930 32 32 0.01
PIN BRG 443 0 0 0.01
Guided brg 32 32 0.01
2.0 SEISMIC LONGITUDINAL
V MAX V MIN PERM V
Inner Brg 1118 996 73 73 0.01
Outer Brg 1122 992 73 73 0.01
PIN BRG 2612 327 0.01
G'DED CONT 327 73 73 0.01
3.0 SEISMIC TRANSVERSE
V MAX V MIN PERM V
Inner Brg 1188 926 32 32 0.01
Outer Brg 1240 874 32 32 0.01
PIN BRG 826 1089 0.01
G'DED CONT 1089 32 32 0.01
4 WIND
V MAX V MIN PERM V
Inner Brg 1668 777 32 32 0.01
Outer Brg 1403 792 32 32 0.01
PIN BRG 442 0.01
G'DED CONT 442 32 32 0.01
13 BEARING STIFFENERS
Outer Bearings
max brg rxn 1668 kN
Clear web height at brg 1.75 m thick. of the web 14 mm
Page 119 of 156

Slenderness ratio 216.51 1.75*SQRT(3)/(14/1000)
Refer cl G4.11.1.1 of IRC 24 2010
fcc pi^2*200000/216.51^2 42
Perm stress in comp 0.6*42*250/(42^1.4+250^1.4)^(1/1.4) 24 mpa, table G12 of IRC 24‐2010
B 2.250 m 1500/2000+2*0.750
σac.t.B 750.2 kN < 1668
Hence brg stiffners are required.
Try 4 Nos. 192 x 16 (2 on either side of web)
Length of outstanding legs 192‐16 = 176 mm
Area of 4 legs 4*16*176= 11264 sqmm
Bearing stress 1668.08724489796*1000/112 148 mpa
Permissible brg stress 200 mpa 0.8*250 (Table G2 of IRC 24)
> 148 ok
CHECK AS STRUTS
Effective legth of web 16*2*14= 448 mm
I of stiffner+Web (448‐16)*14^3/12+16*(192*4+14)^3/12
4
6.38E+08 mm
Area of stiffner + web (448‐16)*14+16*(192*4+14)
18560 sqmm
r 185.36 mm
eff length of strut 0.7*1.75*1000= 1225 mm
l/r 6.61
fcc pi^2*200000/6.61^2 45178
Permissible stress 0.6*45178*250/(45178^1.4+250^1.4)^(1/1.4)
149.9 mpa
limited to 150.0 mpa
Capacity of strut 2783 kN > 1668 kN
hence ok
14 DESIGN OF BRACINGS
14.1 LATERAL BRACING FOR COMPRESSION FLANGE
Lateral bracings are provided to provide lateral restraint to girders till deck slab concrete is green and
not effective.
Max Compressive stress in top flange 137.41 mpa
Area of comp flange 0.015 sqm
Force in comp flange 2061.1 kN
Force for Bracing (2.5% of 5193) 51.528 kN
Comp Force 'F' in one Bracing 38.609 kN
Page 120 of 156

51.528
F
0.84 RAD 2.24
48.14 DEG
5.00
Wind Loads
Height of the bridge 15.0 m
Basic wind speed 47.0 m/sec
Pz 463.7*(47/33)^2= 1040.0 N/sqm
Pz Construction stage 1040*0.7= 728.0 N/sqm
FT Pz. A1. G. CD =728*1.8*2*1.5= 3931.2 N/rm
= 3.931 kN/m
Wind Load for 5.00 m = 19.656 kN
Total force in bracing = 58.26
Length of bracing 1.68 m
Effective length of bracing 1.68*0.7= 1.176 m
Consider 100x100x8 bracing A= 15.39 sqcm
rmin = 1.95 cm
l/r= 60
fcc 542.7 250
all stress 122 mpa
permissible stress with wind 122*1.25= 152.5 mpa
compressive stress 58.26*1000/(15.39*100)= 99 < 152.5 OK
14.2 BRACINGS AT PIN BEARING LOCATION
261.24 T
30deg 0.524deg
1.12
2.24 C/L Brg
INCLINED MEMBER
Force in inclined member 261.24/(2*cos(30)) 150.83 t
Page 121 of 156

Try 2 ISA 200x200x18
As compression member
A 46.61 sq.cm
r min 6.2 cm
L/r 36.129
Permissible stress 141.32*1.4 197.85 mpa
Actual stress 150.83*1e4/(200*46.61) 161.80 mpa <198
As Tension member
Net area 46.61*2‐2.6*4*1.2 80.74 sq.cm
Stress 150.83*1e4/(100*80.74) 186.8 mpa
Permissible stress 0.6 fy x 1.4 210 mpa
STRAIGHT MEMBER
Force in st member 150.83*sin(30)) 75.42 t
As compression member
l/r 36.129
Permissible stress 141.32*1.4 197.85 mpa
Actual stress 75.42*1e4/(200*46.61) 80.9 mpa <198
As Tension member
Net area 46.61*2‐2.6*4*1.2 81 sq.cm
Stress 75.42*1e4/(100*80.74) 93 mpa
Permissible stress 0.6 fy x 1.4 210 mpa
Design of connections
Try M24 Bolts 24
R = (0.35*2*212/1.2)
= 61.83 kN
= 6.18 T
No of bolts for inclined memebr 150.83/6.18 24.4 say 28
No of bolts for straight memebr 75.42/6.18 12.2 say 16
15 DESIGN OF DECK SLAB
As the effective span and the arrangement of precast panels/ in‐situ deck slab is same as that used for
PSC girder spans, same details shall be followed.
Page 122 of 156

APPENDIX A
STAAD INPUT FILES
Page 123 of 156

Page 124 of 156
STAAD SPACE 25+40+25M SPAN (LL)
START JOB INFORMATION
ENGINEER DATE 30-sep-15
END JOB INFORMATION
INPUT WIDTH 79
PAGE LENGTH 15000
UNIT METER MTON
JOINT COORDINATES
1 0 0 0.175; 2 1.9 0 0.175; 3 4.4 0 0.175; 4 6.9 0 0.175; 5 9.4 0 0.175;
6 11.9 0 0.175; 7 14.4 0 0.175; 8 16.9 0 0.175; 9 19.4 0 0.175;
10 21.9 0 0.175; 11 24.4 0 0.175; 12 26.9 0 0.175; 13 29.4 0 0.175;
14 31.9 0 0.175; 15 34.4 0 0.175; 16 36.9 0 0.175; 17 39.4 0 0.175;
18 41.9 0 0.175; 19 44.4 0 0.175; 20 46.9 0 0.175; 21 49.4 0 0.175;
22 51.9 0 0.175; 23 54.4 0 0.175; 24 56.9 0 0.175; 25 59.4 0 0.175;
26 61.9 0 0.175; 27 64.4 0 0.175; 28 66.9 0 0.175; 29 69.4 0 0.175;
30 71.9 0 0.175; 31 74.4 0 0.175; 32 76.9 0 0.175; 33 79.4 0 0.175;
34 81.9 0 0.175; 35 84.4 0 0.175; 36 86.9 0 0.175; 37 88.8 0 0.175; 38 0 0 0;
39 1.9 0 0; 40 4.4 0 0; 41 6.9 0 0; 42 9.4 0 0; 43 11.9 0 0; 44 14.4 0 0;
45 16.9 0 0; 46 19.4 0 0; 47 21.9 0 0; 48 24.4 0 0; 49 26.9 0 0; 50 29.4 0 0;
51 31.9 0 0; 52 34.4 0 0; 53 36.9 0 0; 54 39.4 0 0; 55 41.9 0 0; 56 44.4 0 0;
57 46.9 0 0; 58 49.4 0 0; 59 51.9 0 0; 60 54.4 0 0; 61 56.9 0 0; 62 59.4 0 0;
63 61.9 0 0; 64 64.4 0 0; 65 66.9 0 0; 66 69.4 0 0; 67 71.9 0 0; 68 74.4 0 0;
69 76.9 0 0; 70 79.4 0 0; 71 81.9 0 0; 72 84.4 0 0; 73 86.9 0 0; 74 88.8 0 0;
75 0 0 -2.24; 76 1.9 0 -2.24; 77 4.4 0 -2.24; 78 6.9 0 -2.24; 79 9.4 0 -2.24;
80 11.9 0 -2.24; 81 14.4 0 -2.24; 82 16.9 0 -2.24; 83 19.4 0 -2.24;
84 21.9 0 -2.24; 85 24.4 0 -2.24; 86 26.9 0 -2.24; 87 29.4 0 -2.24;
88 31.9 0 -2.24; 89 34.4 0 -2.24; 90 36.9 0 -2.24; 91 39.4 0 -2.24;
92 41.9 0 -2.24; 93 44.4 0 -2.24; 94 46.9 0 -2.24; 95 49.4 0 -2.24;
96 51.9 0 -2.24; 97 54.4 0 -2.24; 98 56.9 0 -2.24; 99 59.4 0 -2.24;
100 61.9 0 -2.24; 101 64.4 0 -2.24; 102 66.9 0 -2.24; 103 69.4 0 -2.24;
104 71.9 0 -2.24; 105 74.4 0 -2.24; 106 76.9 0 -2.24; 107 79.4 0 -2.24;
108 81.9 0 -2.24; 109 84.4 0 -2.24; 110 86.9 0 -2.24; 111 88.8 0 -2.24;
112 0 0 -4.48; 113 1.9 0 -4.48; 114 4.4 0 -4.48; 115 6.9 0 -4.48;
116 9.4 0 -4.48; 117 11.9 0 -4.48; 118 14.4 0 -4.48; 119 16.9 0 -4.48;
120 19.4 0 -4.48; 121 21.9 0 -4.48; 122 24.4 0 -4.48; 123 26.9 0 -4.48;
124 29.4 0 -4.48; 125 31.9 0 -4.48; 126 34.4 0 -4.48; 127 36.9 0 -4.48;
128 39.4 0 -4.48; 129 41.9 0 -4.48; 130 44.4 0 -4.48; 131 46.9 0 -4.48;
132 49.4 0 -4.48; 133 51.9 0 -4.48; 134 54.4 0 -4.48; 135 56.9 0 -4.48;
136 59.4 0 -4.48; 137 61.9 0 -4.48; 138 64.4 0 -4.48; 139 66.9 0 -4.48;
140 69.4 0 -4.48; 141 71.9 0 -4.48; 142 74.4 0 -4.48; 143 76.9 0 -4.48;
144 79.4 0 -4.48; 145 81.9 0 -4.48; 146 84.4 0 -4.48; 147 86.9 0 -4.48;
148 88.8 0 -4.48; 149 0 0 -6.72; 150 1.9 0 -6.72; 151 4.4 0 -6.72;
152 6.9 0 -6.72; 153 9.4 0 -6.72; 154 11.9 0 -6.72; 155 14.4 0 -6.72;
156 16.9 0 -6.72; 157 19.4 0 -6.72; 158 21.9 0 -6.72; 159 24.4 0 -6.72;
160 26.9 0 -6.72; 161 29.4 0 -6.72; 162 31.9 0 -6.72; 163 34.4 0 -6.72;
164 36.9 0 -6.72; 165 39.4 0 -6.72; 166 41.9 0 -6.72; 167 44.4 0 -6.72;
168 46.9 0 -6.72; 169 49.4 0 -6.72; 170 51.9 0 -6.72; 171 54.4 0 -6.72;
172 56.9 0 -6.72; 173 59.4 0 -6.72; 174 61.9 0 -6.72; 175 64.4 0 -6.72;
176 66.9 0 -6.72; 177 69.4 0 -6.72; 178 71.9 0 -6.72; 179 74.4 0 -6.72;
180 76.9 0 -6.72; 181 79.4 0 -6.72; 182 81.9 0 -6.72; 183 84.4 0 -6.72;
184 86.9 0 -6.72; 185 88.8 0 -6.72; 186 0 0 -8.96; 187 1.9 0 -8.96;
188 4.4 0 -8.96; 189 6.9 0 -8.96; 190 9.4 0 -8.96; 191 11.9 0 -8.96;
192 14.4 0 -8.96; 193 16.9 0 -8.96; 194 19.4 0 -8.96; 195 21.9 0 -8.96;
196 24.4 0 -8.96; 197 26.9 0 -8.96; 198 29.4 0 -8.96; 199 31.9 0 -8.96;
200 34.4 0 -8.96; 201 36.9 0 -8.96; 202 39.4 0 -8.96; 203 41.9 0 -8.96;
204 44.4 0 -8.96; 205 46.9 0 -8.96; 206 49.4 0 -8.96; 207 51.9 0 -8.96;
208 54.4 0 -8.96; 209 56.9 0 -8.96; 210 59.4 0 -8.96; 211 61.9 0 -8.96;
212 64.4 0 -8.96; 213 66.9 0 -8.96; 214 69.4 0 -8.96; 215 71.9 0 -8.96;
216 74.4 0 -8.96; 217 76.9 0 -8.96; 218 79.4 0 -8.96; 219 81.9 0 -8.96;
220 84.4 0 -8.96; 221 86.9 0 -8.96; 222 88.8 0 -8.96; 223 0 0 -11.2;
224 1.9 0 -11.2; 225 4.4 0 -11.2; 226 6.9 0 -11.2; 227 9.4 0 -11.2;
228 11.9 0 -11.2; 229 14.4 0 -11.2; 230 16.9 0 -11.2; 231 19.4 0 -11.2;
232 21.9 0 -11.2; 233 24.4 0 -11.2; 234 26.9 0 -11.2; 235 29.4 0 -11.2;
236 31.9 0 -11.2; 237 34.4 0 -11.2; 238 36.9 0 -11.2; 239 39.4 0 -11.2;
240 41.9 0 -11.2; 241 44.4 0 -11.2; 242 46.9 0 -11.2; 243 49.4 0 -11.2;
244 51.9 0 -11.2; 245 54.4 0 -11.2; 246 56.9 0 -11.2; 247 59.4 0 -11.2;
248 61.9 0 -11.2; 249 64.4 0 -11.2; 250 66.9 0 -11.2; 251 69.4 0 -11.2;
252 71.9 0 -11.2; 253 74.4 0 -11.2; 254 76.9 0 -11.2; 255 79.4 0 -11.2;
256 81.9 0 -11.2; 257 84.4 0 -11.2; 258 86.9 0 -11.2; 259 88.8 0 -11.2;
260 0 0 -11.375; 261 1.9 0 -11.375; 262 4.4 0 -11.375; 263 6.9 0 -11.375;
264 9.4 0 -11.375; 265 11.9 0 -11.375; 266 14.4 0 -11.375; 267 16.9 0 -11.375;
268 19.4 0 -11.375; 269 21.9 0 -11.375; 270 24.4 0 -11.375; 271 26.9 0 -11.375;
272 29.4 0 -11.375; 273 31.9 0 -11.375; 274 34.4 0 -11.375; 275 36.9 0 -11.375;
Page 125 of 156
276 39.4 0 -11.375; 277 41.9 0 -11.375; 278 44.4 0 -11.375; 279 46.9 0 -11.375;
280 49.4 0 -11.375; 281 51.9 0 -11.375; 282 54.4 0 -11.375; 283 56.9 0 -11.375;
284 59.4 0 -11.375; 285 61.9 0 -11.375; 286 64.4 0 -11.375; 287 66.9 0 -11.375;
288 69.4 0 -11.375; 289 71.9 0 -11.375; 290 74.4 0 -11.375; 291 76.9 0 -11.375;
292 79.4 0 -11.375; 293 81.9 0 -11.375; 294 84.4 0 -11.375; 295 86.9 0 -11.375;
296 88.8 0 -11.375; 301 9.4 0 0.55; 302 11.9 0 0.55; 303 14.4 0 0.55;
304 16.9 0 0.55; 305 31.9 0 0.55; 306 34.4 0 0.55; 307 36.9 0 0.55;
308 39.4 0 0.55; 309 49.4 0 0.55; 310 51.9 0 0.55; 311 54.4 0 0.55;
312 56.9 0 0.55; 313 71.9 0 0.55; 314 74.4 0 0.55; 315 76.9 0 0.55;
316 79.4 0 0.55; 317 9.4 0 -11.75; 318 11.9 0 -11.75; 319 14.4 0 -11.75;
320 16.9 0 -11.75; 321 31.9 0 -11.75; 322 34.4 0 -11.75; 323 36.9 0 -11.75;
324 39.4 0 -11.75; 325 49.4 0 -11.75; 326 51.9 0 -11.75; 327 54.4 0 -11.75;
328 56.9 0 -11.75; 329 71.9 0 -11.75; 330 74.4 0 -11.75; 331 76.9 0 -11.75;
332 79.4 0 -11.75; 333 24.4 3 0.55; 334 24.4 4 0.55; 335 24.4 5 0.55;
336 24.4 6 0.55; 337 64.4 3 0.55; 338 64.4 4 0.55; 339 64.4 5 0.55;
340 64.4 6 0.55; 341 24.4 3 -11.75; 342 24.4 4 -11.75; 343 24.4 5 -11.75;
344 24.4 6 -11.75; 345 64.4 3 -11.75; 346 64.4 4 -11.75; 347 64.4 5 -11.75;
348 64.4 6 -11.75; 349 24.4 -1.154 1.23; 350 24.4 0.666 1.23;
351 24.4 5.5 0.55; 352 24.4 7 0.55; 353 24.4 10.09 0.55; 354 64.4 -1.154 1.23;
355 64.4 0.666 1.23; 356 64.4 5.5 0.55; 357 64.4 7 0.55; 358 64.4 10.09 0.55;
359 24.4 -1.154 -12.43; 360 24.4 0.666 -12.43; 361 24.4 5.5 -11.75;
362 24.4 7 -11.75; 363 24.4 10.09 -11.75; 364 64.4 -1.154 -12.43;
365 64.4 0.666 -12.43; 366 64.4 5.5 -11.75; 367 64.4 7 -11.75;
368 64.4 10.09 -11.75; 369 24.4 3.1 0.55; 370 24.4 4.1 0.55; 371 24.4 5.1 0.55;
372 24.4 6.1 0.55; 373 64.4 3.1 0.55; 374 64.4 4.1 0.55; 375 64.4 5.1 0.55;
376 64.4 6.1 0.55; 377 24.4 3.1 -11.75; 378 24.4 4.1 -11.75;
379 24.4 5.1 -11.75; 380 24.4 6.1 -11.75; 381 64.4 3.1 -11.75;
382 64.4 4.1 -11.75; 383 64.4 5.1 -11.75; 384 64.4 6.1 -11.75;
MEMBER INCIDENCES
1 1 2; 2 2 3; 3 3 4; 4 4 5; 5 5 6; 6 6 7; 7 7 8; 8 8 9; 9 9 10; 10 10 11;
11 11 12; 12 12 13; 13 13 14; 14 14 15; 15 15 16; 16 16 17; 17 17 18; 18 18 19;
19 19 20; 20 20 21; 21 21 22; 22 22 23; 23 23 24; 24 24 25; 25 25 26; 26 26 27;
27 27 28; 28 28 29; 29 29 30; 30 30 31; 31 31 32; 32 32 33; 33 33 34; 34 34 35;
35 35 36; 36 36 37; 37 38 39; 38 39 40; 39 40 41; 40 41 42; 41 42 43; 42 43 44;
43 44 45; 44 45 46; 45 46 47; 46 47 48; 47 48 49; 48 49 50; 49 50 51; 50 51 52;
51 52 53; 52 53 54; 53 54 55; 54 55 56; 55 56 57; 56 57 58; 57 58 59; 58 59 60;
59 60 61; 60 61 62; 61 62 63; 62 63 64; 63 64 65; 64 65 66; 65 66 67; 66 67 68;
67 68 69; 68 69 70; 69 70 71; 70 71 72; 71 72 73; 72 73 74; 73 75 76; 74 76 77;
75 77 78; 76 78 79; 77 79 80; 78 80 81; 79 81 82; 80 82 83; 81 83 84; 82 84 85;
83 85 86; 84 86 87; 85 87 88; 86 88 89; 87 89 90; 88 90 91; 89 91 92; 90 92 93;
91 93 94; 92 94 95; 93 95 96; 94 96 97; 95 97 98; 96 98 99; 97 99 100;
98 100 101; 99 101 102; 100 102 103; 101 103 104; 102 104 105; 103 105 106;
104 106 107; 105 107 108; 106 108 109; 107 109 110; 108 110 111; 109 112 113;
110 113 114; 111 114 115; 112 115 116; 113 116 117; 114 117 118; 115 118 119;
116 119 120; 117 120 121; 118 121 122; 119 122 123; 120 123 124; 121 124 125;
122 125 126; 123 126 127; 124 127 128; 125 128 129; 126 129 130; 127 130 131;
128 131 132; 129 132 133; 130 133 134; 131 134 135; 132 135 136; 133 136 137;
134 137 138; 135 138 139; 136 139 140; 137 140 141; 138 141 142; 139 142 143;
140 143 144; 141 144 145; 142 145 146; 143 146 147; 144 147 148; 145 149 150;
146 150 151; 147 151 152; 148 152 153; 149 153 154; 150 154 155; 151 155 156;
152 156 157; 153 157 158; 154 158 159; 155 159 160; 156 160 161; 157 161 162;
158 162 163; 159 163 164; 160 164 165; 161 165 166; 162 166 167; 163 167 168;
164 168 169; 165 169 170; 166 170 171; 167 171 172; 168 172 173; 169 173 174;
170 174 175; 171 175 176; 172 176 177; 173 177 178; 174 178 179; 175 179 180;
176 180 181; 177 181 182; 178 182 183; 179 183 184; 180 184 185; 181 186 187;
182 187 188; 183 188 189; 184 189 190; 185 190 191; 186 191 192; 187 192 193;
188 193 194; 189 194 195; 190 195 196; 191 196 197; 192 197 198; 193 198 199;
194 199 200; 195 200 201; 196 201 202; 197 202 203; 198 203 204; 199 204 205;
200 205 206; 201 206 207; 202 207 208; 203 208 209; 204 209 210; 205 210 211;
206 211 212; 207 212 213; 208 213 214; 209 214 215; 210 215 216; 211 216 217;
212 217 218; 213 218 219; 214 219 220; 215 220 221; 216 221 222; 217 223 224;
218 224 225; 219 225 226; 220 226 227; 221 227 228; 222 228 229; 223 229 230;
224 230 231; 225 231 232; 226 232 233; 227 233 234; 228 234 235; 229 235 236;
230 236 237; 231 237 238; 232 238 239; 233 239 240; 234 240 241; 235 241 242;
236 242 243; 237 243 244; 238 244 245; 239 245 246; 240 246 247; 241 247 248;
242 248 249; 243 249 250; 244 250 251; 245 251 252; 246 252 253; 247 253 254;
248 254 255; 249 255 256; 250 256 257; 251 257 258; 252 258 259; 253 260 261;
254 261 262; 255 262 263; 256 263 264; 257 264 265; 258 265 266; 259 266 267;
260 267 268; 261 268 269; 262 269 270; 263 270 271; 264 271 272; 265 272 273;
266 273 274; 267 274 275; 268 275 276; 269 276 277; 270 277 278; 271 278 279;
272 279 280; 273 280 281; 274 281 282; 275 282 283; 276 283 284; 277 284 285;
278 285 286; 279 286 287; 280 287 288; 281 288 289; 282 289 290; 283 290 291;
284 291 292; 285 292 293; 286 293 294; 287 294 295; 288 295 296; 301 1 38;
Page 126 of 156
302 38 75; 303 75 112; 304 112 149; 305 149 186; 306 186 223; 307 223 260;
308 2 39; 309 39 76; 310 76 113; 311 113 150; 312 150 187; 313 187 224;
314 224 261; 315 3 40; 316 40 77; 317 77 114; 318 114 151; 319 151 188;
320 188 225; 321 225 262; 322 4 41; 323 41 78; 324 78 115; 325 115 152;
326 152 189; 327 189 226; 328 226 263; 329 5 42; 330 42 79; 331 79 116;
332 116 153; 333 153 190; 334 190 227; 335 227 264; 336 6 43; 337 43 80;
338 80 117; 339 117 154; 340 154 191; 341 191 228; 342 228 265; 343 7 44;
344 44 81; 345 81 118; 346 118 155; 347 155 192; 348 192 229; 349 229 266;
350 8 45; 351 45 82; 352 82 119; 353 119 156; 354 156 193; 355 193 230;
356 230 267; 357 9 46; 358 46 83; 359 83 120; 360 120 157; 361 157 194;
362 194 231; 363 231 268; 364 10 47; 365 47 84; 366 84 121; 367 121 158;
368 158 195; 369 195 232; 370 232 269; 371 11 48; 372 48 85; 373 85 122;
374 122 159; 375 159 196; 376 196 233; 377 233 270; 378 12 49; 379 49 86;
380 86 123; 381 123 160; 382 160 197; 383 197 234; 384 234 271; 385 13 50;
386 50 87; 387 87 124; 388 124 161; 389 161 198; 390 198 235; 391 235 272;
392 14 51; 393 51 88; 394 88 125; 395 125 162; 396 162 199; 397 199 236;
398 236 273; 399 15 52; 400 52 89; 401 89 126; 402 126 163; 403 163 200;
404 200 237; 405 237 274; 406 16 53; 407 53 90; 408 90 127; 409 127 164;
410 164 201; 411 201 238; 412 238 275; 413 17 54; 414 54 91; 415 91 128;
416 128 165; 417 165 202; 418 202 239; 419 239 276; 420 18 55; 421 55 92;
422 92 129; 423 129 166; 424 166 203; 425 203 240; 426 240 277; 427 19 56;
428 56 93; 429 93 130; 430 130 167; 431 167 204; 432 204 241; 433 241 278;
434 20 57; 435 57 94; 436 94 131; 437 131 168; 438 168 205; 439 205 242;
440 242 279; 441 21 58; 442 58 95; 443 95 132; 444 132 169; 445 169 206;
446 206 243; 447 243 280; 448 22 59; 449 59 96; 450 96 133; 451 133 170;
452 170 207; 453 207 244; 454 244 281; 455 23 60; 456 60 97; 457 97 134;
458 134 171; 459 171 208; 460 208 245; 461 245 282; 462 24 61; 463 61 98;
464 98 135; 465 135 172; 466 172 209; 467 209 246; 468 246 283; 469 25 62;
470 62 99; 471 99 136; 472 136 173; 473 173 210; 474 210 247; 475 247 284;
476 26 63; 477 63 100; 478 100 137; 479 137 174; 480 174 211; 481 211 248;
482 248 285; 483 27 64; 484 64 101; 485 101 138; 486 138 175; 487 175 212;
488 212 249; 489 249 286; 490 28 65; 491 65 102; 492 102 139; 493 139 176;
494 176 213; 495 213 250; 496 250 287; 497 29 66; 498 66 103; 499 103 140;
500 140 177; 501 177 214; 502 214 251; 503 251 288; 504 30 67; 505 67 104;
506 104 141; 507 141 178; 508 178 215; 509 215 252; 510 252 289; 511 31 68;
512 68 105; 513 105 142; 514 142 179; 515 179 216; 516 216 253; 517 253 290;
518 32 69; 519 69 106; 520 106 143; 521 143 180; 522 180 217; 523 217 254;
524 254 291; 525 33 70; 526 70 107; 527 107 144; 528 144 181; 529 181 218;
530 218 255; 531 255 292; 532 34 71; 533 71 108; 534 108 145; 535 145 182;
536 182 219; 537 219 256; 538 256 293; 539 35 72; 540 72 109; 541 109 146;
542 146 183; 543 183 220; 544 220 257; 545 257 294; 546 36 73; 547 73 110;
548 110 147; 549 147 184; 550 184 221; 551 221 258; 552 258 295; 553 37 74;
554 74 111; 555 111 148; 556 148 185; 557 185 222; 558 222 259; 559 259 296;
601 5 301; 602 6 302; 603 7 303; 604 8 304; 605 14 305; 606 15 306; 607 16 307;
608 17 308; 609 21 309; 610 22 310; 611 23 311; 612 24 312; 613 30 313;
614 31 314; 615 32 315; 616 33 316; 617 264 317; 618 265 318; 619 266 319;
620 267 320; 621 273 321; 622 274 322; 623 275 323; 624 276 324; 625 280 325;
626 281 326; 627 282 327; 628 283 328; 629 289 329; 630 290 330; 631 291 331;
632 292 332; 633 301 372; 634 302 371; 635 303 370; 636 304 369; 637 305 369;
638 306 370; 639 307 371; 640 308 372; 641 309 376; 642 310 375; 643 311 374;
644 312 373; 645 313 373; 646 314 374; 647 315 375; 648 316 376; 649 317 380;
650 318 379; 651 319 378; 652 320 377; 653 321 377; 654 322 378; 655 323 379;
656 324 380; 657 325 384; 658 326 383; 659 327 382; 660 328 381; 661 329 381;
662 330 382; 663 331 383; 664 332 384; 665 349 350; 666 350 333; 667 333 334;
668 334 335; 669 335 351; 670 351 336; 671 336 352; 672 352 353; 673 354 355;
674 355 337; 675 337 338; 676 338 339; 677 339 356; 678 356 340; 679 340 357;
680 357 358; 681 359 360; 682 360 341; 683 341 342; 684 342 343; 685 343 361;
686 361 344; 687 344 362; 688 362 363; 689 364 365; 690 365 345; 691 345 346;
692 346 347; 693 347 366; 694 366 348; 695 348 367; 696 367 368; 697 351 361;
698 356 366; 699 333 369; 700 334 370; 701 335 371; 702 336 372; 703 337 373;
704 338 374; 705 339 375; 706 340 376; 707 341 377; 708 342 378; 709 343 379;
710 344 380; 711 345 381; 712 346 382; 713 347 383; 714 348 384;
MEMBER PROPERTY CANADIAN
*FOR T LOADS
1 to 36 253 to 288 PRI AX 0.008 IX 0.000001 IY 0.0001 IZ 0.000001
37 TO 41 68 TO 72 217 TO 221 248 TO 252 PRI AX 0.1021 IX 0.000001 IY 0.011 -
IZ 0.057
42 67 222 247 PRI AX 0.0977 IX 0.000001 IY 0.009 IZ 0.056
43 44 65 66 223 224 245 246 PRI AX 0.0933 IX 0.000001 IY 0.006 IZ 0.054
45 64 225 244 PRI AX 0.0862 IX 0.000001 IY 0.004 IZ 0.051
46 47 62 63 226 227 242 243 PRI AX 0.0855 IX 0.000001 IY 0.004 IZ 0.051
48 61 228 241 PRI AX 0.0926 IX 0.000001 IY 0.006 IZ 0.054
49 50 59 60 229 230 239 240 PRI AX 0.0997 IX 0.000001 IY 0.01 IZ 0.057
Page 127 of 156
51 52 57 58 231 232 237 238 PRI AX 0.1028 IX 0.000001 IY 0.012 IZ 0.058
53 TO 56 233 TO 236 PRI AX 0.1059 IX 0.000001 IY 0.014 IZ 0.058
73 TO 77 109 TO 113 145 TO 149 181 TO 185 104 TO 108 140 TO 144 176 TO 180 -
212 TO 216 PRI AX 0.11 IX 0.000001 IY 0.018 IZ 0.06
78 114 150 186 103 139 175 211 PRI AX 0.105 IX 0.000001 IY 0.013 IZ 0.059
79 80 115 116 151 152 187 188 102 101 138 137 174 173 210 209 PRI AX 0.1 -
IX 0.000001 IY 0.01 IZ 0.057
81 117 153 189 100 136 172 208 PRI AX 0.0919 IX 0.000001 IY 0.006 IZ 0.054
82 83 118 119 154 155 190 191 99 98 135 134 171 170 207 206 PRI AX 0.0911 -
IX 0.000001 IY 0.005 IZ 0.054
84 120 156 192 97 133 169 205 PRI AX 0.0992 IX 0.000001 IY 0.009 IZ 0.057
85 86 121 122 157 158 193 194 96 95 132 131 168 167 204 203 PRI AX 0.1073 -
IX 0.000001 IY 0.015 IZ 0.059
87 88 123 124 159 160 195 196 94 93 130 129 166 165 202 201 PRI AX 0.1108 -
IX 0.000001 IY 0.018 IZ 0.06
89 90 125 126 161 162 197 198 92 91 128 127 164 163 200 199 PRI AX 0.1143 -
IX 0.000001 IY 0.022 IZ 0.061
301 307 553 559 PRI AX 0.041 IX 0.000001 IY 0.0083 IZ 0.0001
302 to 306 372 to 376 484 to 488 554 TO 558 PRI AX 0.044 IX 0.000001 -
IY 0.00053 IZ 0.0161
308 to 328 357 to 371 377 to 391 420 to 440 469 to 483 489 to 503 532 to 552 -
PRI AX 0.067 IX 0.000001 IY 0.0347 IZ 0.0002
329 to 356 392 to 419 441 to 468 504 to 531 PRI AX 0.026 IX 0.000001 -
IY 0.00009 IZ 0.0079
601 TO 632 PRI AX 0.1 IX 0.000001 IY 0.01 IZ 0.01
633 TO 664 PRI AX 0.00056 IX 0.000001 IY 0.000000025 IZ 0.000000025
665 673 681 689 TAPERED 1.5 0.4 1.743 0.8 0.4 0.8 0.4
666 674 682 690 TAPERED 1.743 0.4 2.052 0.8 0.4 0.8 0.4
667 675 683 691 699 703 707 711 TAPERED 2.052 0.4 2.185 0.8 0.4 0.8 0.4
668 676 684 692 700 704 708 712 TAPERED 2.185 0.4 2.318 0.8 0.4 0.8 0.4
669 677 685 693 701 705 709 713 TAPERED 2.318 0.4 2.385 0.8 0.4 0.8 0.4
670 678 686 694 702 706 710 714 TAPERED 2.385 0.4 2.415 0.8 0.4 0.8 0.4
671 679 687 695 TAPERED 2.415 0.4 2.5084 0.8 0.4 0.8 0.4
672 680 688 696 TAPERED 2.5084 0.4 3 0.8 0.4 0.8 0.4
697 698 PRIS YD 1 ZD 0.6
DEFINE MATERIAL START
ISOTROPIC MATERIAL1
E 2.11e+007
POISSON 0.3
DENSITY 7.85
ALPHA 1.2e-005
ISOTROPIC CONCRETE
E 3.2e+006
POISSON 0.17
DENSITY 2.5
ALPHA 1e-005
DAMP 0.05
END DEFINE MATERIAL
CONSTANTS
MATERIAL MATERIAL1 ALL
MATERIAL CONCRETE MEMB 665 TO 714
SUPPORTS
38 FIXED BUT FX MX MY MZ
75 112 149 186 223 FIXED BUT FX FZ MX MY MZ
48 FIXED BUT FX FZ MX MY MZ
122 159 PINNED
196 233 FIXED BUT FX FZ MX MY MZ
349 354 359 364 FIXED
MEMBER RELEASE
*633 TO 636 641 TO 643 649 TO 652 657 TO 660 END FY MX MY MZ
699 TO 714 END FY MX MY MZ
DEFINE MOVING LOAD
*CLASS A
TYPE 1 LOAD 3.4 3.4 3.4 3.4 5.7 5.7 1.35 1.35
Page 128 of 156
DIST 3 3 3 4.3 1.2 3.2 1.1 WID 1.8
*CLASS 70R W
TYPE 2 LOAD 4 6 6 8.5 8.5 8.5 8.5
DIST 3.96 1.52 2.13 1.37 3.05 1.37 WID 1.93
LOAD GENERATION 150
*70R ecc MEDIAN SIDE
TYPE 2 -13.4 0 -1.68 XINC 0.6
*70R CONC
*TYPE 2 -13.4 0 -4.635 XINC 0.6
*CLASS A TWO LANE eccentric
*TYPE 1 -18.8 0 -0.45 XINC 0.6
*TYPE 1 -18.8 0 -3.95 XINC 0.6
*CLASS A TWO LANE concentric
*TYPE 1 -18.8 0 -2.95 XINC 0.6
*TYPE 1 -18.8 0 -6.45 XINC 0.6
*70R ecc FOOTPATH SIDE
*TYPE 2 -13.4 0 -5.59 XINC 0.6
PERFORM ANALYSIS
PRINT FORCE ENVELOPE NSECTION 1 LIST 37 TO 54 73 TO 90 109 TO 126 145 TO 162 -
181 TO 198 216 TO 234
PRINT FORCE ENVELOPE NSECTION 1 LIST 301 TO 307 329 TO 356 371 TO 377 392 -
393 TO 419 441 TO 468 483 TO 489 504 TO 531 553 TO 559
PRINT FORCE ENVELOPE NSECTION 1 LIST 633 TO 664
PRINT SUPPORT REACTION
FINISH
Page 129 of 156

STAAD SPACE 25M SPAN (DIFF SETTLEMENT)
ENGINEER DATE 30-Nov-13
END JOB INFORMATION
INPUT WIDTH 79
PAGE LENGTH 15000
UNIT METER MTON
JOINT COORDINATES
1 0 0 0.175; 2 1.9 0 0.175; 3 4.4 0 0.175; 4 6.9 0 0.175; 5 9.4 0 0.175;
6 11.9 0 0.175; 7 14.4 0 0.175; 8 16.9 0 0.175; 9 19.4 0 0.175;
10 21.9 0 0.175; 11 24.4 0 0.175; 12 26.9 0 0.175; 13 29.4 0 0.175;
14 31.9 0 0.175; 15 34.4 0 0.175; 16 36.9 0 0.175; 17 39.4 0 0.175;
18 41.9 0 0.175; 19 44.4 0 0.175; 20 46.9 0 0.175; 21 49.4 0 0.175;
22 51.9 0 0.175; 23 54.4 0 0.175; 24 56.9 0 0.175; 25 59.4 0 0.175;
26 61.9 0 0.175; 27 64.4 0 0.175; 28 66.9 0 0.175; 29 69.4 0 0.175;
30 71.9 0 0.175; 31 74.4 0 0.175; 32 76.9 0 0.175; 33 79.4 0 0.175;
34 81.9 0 0.175; 35 84.4 0 0.175; 36 86.9 0 0.175; 37 88.8 0 0.175; 38 0 0 0;
39 1.9 0 0; 40 4.4 0 0; 41 6.9 0 0; 42 9.4 0 0; 43 11.9 0 0; 44 14.4 0 0;
45 16.9 0 0; 46 19.4 0 0; 47 21.9 0 0; 48 24.4 0 0; 49 26.9 0 0; 50 29.4 0 0;
51 31.9 0 0; 52 34.4 0 0; 53 36.9 0 0; 54 39.4 0 0; 55 41.9 0 0; 56 44.4 0 0;
57 46.9 0 0; 58 49.4 0 0; 59 51.9 0 0; 60 54.4 0 0; 61 56.9 0 0; 62 59.4 0 0;
63 61.9 0 0; 64 64.4 0 0; 65 66.9 0 0; 66 69.4 0 0; 67 71.9 0 0; 68 74.4 0 0;
69 76.9 0 0; 70 79.4 0 0; 71 81.9 0 0; 72 84.4 0 0; 73 86.9 0 0; 74 88.8 0 0;
75 0 0 -2.24; 76 1.9 0 -2.24; 77 4.4 0 -2.24; 78 6.9 0 -2.24; 79 9.4 0 -2.24;
80 11.9 0 -2.24; 81 14.4 0 -2.24; 82 16.9 0 -2.24; 83 19.4 0 -2.24;
84 21.9 0 -2.24; 85 24.4 0 -2.24; 86 26.9 0 -2.24; 87 29.4 0 -2.24;
88 31.9 0 -2.24; 89 34.4 0 -2.24; 90 36.9 0 -2.24; 91 39.4 0 -2.24;
92 41.9 0 -2.24; 93 44.4 0 -2.24; 94 46.9 0 -2.24; 95 49.4 0 -2.24;
96 51.9 0 -2.24; 97 54.4 0 -2.24; 98 56.9 0 -2.24; 99 59.4 0 -2.24;
100 61.9 0 -2.24; 101 64.4 0 -2.24; 102 66.9 0 -2.24; 103 69.4 0 -2.24;
104 71.9 0 -2.24; 105 74.4 0 -2.24; 106 76.9 0 -2.24; 107 79.4 0 -2.24;
108 81.9 0 -2.24; 109 84.4 0 -2.24; 110 86.9 0 -2.24; 111 88.8 0 -2.24;
112 0 0 -4.48; 113 1.9 0 -4.48; 114 4.4 0 -4.48; 115 6.9 0 -4.48;
116 9.4 0 -4.48; 117 11.9 0 -4.48; 118 14.4 0 -4.48; 119 16.9 0 -4.48;
120 19.4 0 -4.48; 121 21.9 0 -4.48; 122 24.4 0 -4.48; 123 26.9 0 -4.48;
124 29.4 0 -4.48; 125 31.9 0 -4.48; 126 34.4 0 -4.48; 127 36.9 0 -4.48;
128 39.4 0 -4.48; 129 41.9 0 -4.48; 130 44.4 0 -4.48; 131 46.9 0 -4.48;
132 49.4 0 -4.48; 133 51.9 0 -4.48; 134 54.4 0 -4.48; 135 56.9 0 -4.48;
136 59.4 0 -4.48; 137 61.9 0 -4.48; 138 64.4 0 -4.48; 139 66.9 0 -4.48;
140 69.4 0 -4.48; 141 71.9 0 -4.48; 142 74.4 0 -4.48; 143 76.9 0 -4.48;
144 79.4 0 -4.48; 145 81.9 0 -4.48; 146 84.4 0 -4.48; 147 86.9 0 -4.48;
148 88.8 0 -4.48; 149 0 0 -6.72; 150 1.9 0 -6.72; 151 4.4 0 -6.72;
152 6.9 0 -6.72; 153 9.4 0 -6.72; 154 11.9 0 -6.72; 155 14.4 0 -6.72;
156 16.9 0 -6.72; 157 19.4 0 -6.72; 158 21.9 0 -6.72; 159 24.4 0 -6.72;
160 26.9 0 -6.72; 161 29.4 0 -6.72; 162 31.9 0 -6.72; 163 34.4 0 -6.72;
164 36.9 0 -6.72; 165 39.4 0 -6.72; 166 41.9 0 -6.72; 167 44.4 0 -6.72;
168 46.9 0 -6.72; 169 49.4 0 -6.72; 170 51.9 0 -6.72; 171 54.4 0 -6.72;
172 56.9 0 -6.72; 173 59.4 0 -6.72; 174 61.9 0 -6.72; 175 64.4 0 -6.72;
176 66.9 0 -6.72; 177 69.4 0 -6.72; 178 71.9 0 -6.72; 179 74.4 0 -6.72;
180 76.9 0 -6.72; 181 79.4 0 -6.72; 182 81.9 0 -6.72; 183 84.4 0 -6.72;
184 86.9 0 -6.72; 185 88.8 0 -6.72; 186 0 0 -8.96; 187 1.9 0 -8.96;
188 4.4 0 -8.96; 189 6.9 0 -8.96; 190 9.4 0 -8.96; 191 11.9 0 -8.96;
192 14.4 0 -8.96; 193 16.9 0 -8.96; 194 19.4 0 -8.96; 195 21.9 0 -8.96;
196 24.4 0 -8.96; 197 26.9 0 -8.96; 198 29.4 0 -8.96; 199 31.9 0 -8.96;
200 34.4 0 -8.96; 201 36.9 0 -8.96; 202 39.4 0 -8.96; 203 41.9 0 -8.96;
204 44.4 0 -8.96; 205 46.9 0 -8.96; 206 49.4 0 -8.96; 207 51.9 0 -8.96;
208 54.4 0 -8.96; 209 56.9 0 -8.96; 210 59.4 0 -8.96; 211 61.9 0 -8.96;
212 64.4 0 -8.96; 213 66.9 0 -8.96; 214 69.4 0 -8.96; 215 71.9 0 -8.96;
216 74.4 0 -8.96; 217 76.9 0 -8.96; 218 79.4 0 -8.96; 219 81.9 0 -8.96;
220 84.4 0 -8.96; 221 86.9 0 -8.96; 222 88.8 0 -8.96; 223 0 0 -11.2;
224 1.9 0 -11.2; 225 4.4 0 -11.2; 226 6.9 0 -11.2; 227 9.4 0 -11.2;
228 11.9 0 -11.2; 229 14.4 0 -11.2; 230 16.9 0 -11.2; 231 19.4 0 -11.2;
232 21.9 0 -11.2; 233 24.4 0 -11.2; 234 26.9 0 -11.2; 235 29.4 0 -11.2;
236 31.9 0 -11.2; 237 34.4 0 -11.2; 238 36.9 0 -11.2; 239 39.4 0 -11.2;
240 41.9 0 -11.2; 241 44.4 0 -11.2; 242 46.9 0 -11.2; 243 49.4 0 -11.2;
244 51.9 0 -11.2; 245 54.4 0 -11.2; 246 56.9 0 -11.2; 247 59.4 0 -11.2;
248 61.9 0 -11.2; 249 64.4 0 -11.2; 250 66.9 0 -11.2; 251 69.4 0 -11.2;
252 71.9 0 -11.2; 253 74.4 0 -11.2; 254 76.9 0 -11.2; 255 79.4 0 -11.2;
256 81.9 0 -11.2; 257 84.4 0 -11.2; 258 86.9 0 -11.2; 259 88.8 0 -11.2;
260 0 0 -11.375; 261 1.9 0 -11.375; 262 4.4 0 -11.375; 263 6.9 0 -11.375;
264 9.4 0 -11.375; 265 11.9 0 -11.375; 266 14.4 0 -11.375; 267 16.9 0 -11.375;
268 19.4 0 -11.375; 269 21.9 0 -11.375; 270 24.4 0 -11.375; 271 26.9 0 -11.375;
272 29.4 0 -11.375; 273 31.9 0 -11.375; 274 34.4 0 -11.375; 275 36.9 0 -11.375;
Page 130 of 156
276 39.4 0 -11.375; 277 41.9 0 -11.375; 278 44.4 0 -11.375; 279 46.9 0 -11.375;
280 49.4 0 -11.375; 281 51.9 0 -11.375; 282 54.4 0 -11.375; 283 56.9 0 -11.375;
284 59.4 0 -11.375; 285 61.9 0 -11.375; 286 64.4 0 -11.375; 287 66.9 0 -11.375;
288 69.4 0 -11.375; 289 71.9 0 -11.375; 290 74.4 0 -11.375; 291 76.9 0 -11.375;
292 79.4 0 -11.375; 293 81.9 0 -11.375; 294 84.4 0 -11.375; 295 86.9 0 -11.375;
296 88.8 0 -11.375; 301 9.4 0 0.55; 302 11.9 0 0.55; 303 14.4 0 0.55;
304 16.9 0 0.55; 305 31.9 0 0.55; 306 34.4 0 0.55; 307 36.9 0 0.55;
308 39.4 0 0.55; 309 49.4 0 0.55; 310 51.9 0 0.55; 311 54.4 0 0.55;
312 56.9 0 0.55; 313 71.9 0 0.55; 314 74.4 0 0.55; 315 76.9 0 0.55;
316 79.4 0 0.55; 317 9.4 0 -11.75; 318 11.9 0 -11.75; 319 14.4 0 -11.75;
320 16.9 0 -11.75; 321 31.9 0 -11.75; 322 34.4 0 -11.75; 323 36.9 0 -11.75;
324 39.4 0 -11.75; 325 49.4 0 -11.75; 326 51.9 0 -11.75; 327 54.4 0 -11.75;
328 56.9 0 -11.75; 329 71.9 0 -11.75; 330 74.4 0 -11.75; 331 76.9 0 -11.75;
332 79.4 0 -11.75; 333 24.4 3 0.55; 334 24.4 4 0.55; 335 24.4 5 0.55;
336 24.4 6 0.55; 337 64.4 3 0.55; 338 64.4 4 0.55; 339 64.4 5 0.55;
340 64.4 6 0.55; 341 24.4 3 -11.75; 342 24.4 4 -11.75; 343 24.4 5 -11.75;
344 24.4 6 -11.75; 345 64.4 3 -11.75; 346 64.4 4 -11.75; 347 64.4 5 -11.75;
348 64.4 6 -11.75; 349 24.4 -1.154 1.23; 350 24.4 0.666 1.23;
351 24.4 5.5 0.55; 352 24.4 7 0.55; 353 24.4 10.09 0.55; 354 64.4 -1.154 1.23;
355 64.4 0.666 1.23; 356 64.4 5.5 0.55; 357 64.4 7 0.55; 358 64.4 10.09 0.55;
359 24.4 -1.154 -12.43; 360 24.4 0.666 -12.43; 361 24.4 5.5 -11.75;
362 24.4 7 -11.75; 363 24.4 10.09 -11.75; 364 64.4 -1.154 -12.43;
365 64.4 0.666 -12.43; 366 64.4 5.5 -11.75; 367 64.4 7 -11.75;
368 64.4 10.09 -11.75; 369 24.4 3.1 0.55; 370 24.4 4.1 0.55; 371 24.4 5.1 0.55;
372 24.4 6.1 0.55; 373 64.4 3.1 0.55; 374 64.4 4.1 0.55; 375 64.4 5.1 0.55;
376 64.4 6.1 0.55; 377 24.4 3.1 -11.75; 378 24.4 4.1 -11.75;
379 24.4 5.1 -11.75; 380 24.4 6.1 -11.75; 381 64.4 3.1 -11.75;
382 64.4 4.1 -11.75; 383 64.4 5.1 -11.75; 384 64.4 6.1 -11.75;
MEMBER INCIDENCES
1 1 2; 2 2 3; 3 3 4; 4 4 5; 5 5 6; 6 6 7; 7 7 8; 8 8 9; 9 9 10; 10 10 11;
11 11 12; 12 12 13; 13 13 14; 14 14 15; 15 15 16; 16 16 17; 17 17 18; 18 18 19;
19 19 20; 20 20 21; 21 21 22; 22 22 23; 23 23 24; 24 24 25; 25 25 26; 26 26 27;
27 27 28; 28 28 29; 29 29 30; 30 30 31; 31 31 32; 32 32 33; 33 33 34; 34 34 35;
35 35 36; 36 36 37; 37 38 39; 38 39 40; 39 40 41; 40 41 42; 41 42 43; 42 43 44;
43 44 45; 44 45 46; 45 46 47; 46 47 48; 47 48 49; 48 49 50; 49 50 51; 50 51 52;
51 52 53; 52 53 54; 53 54 55; 54 55 56; 55 56 57; 56 57 58; 57 58 59; 58 59 60;
59 60 61; 60 61 62; 61 62 63; 62 63 64; 63 64 65; 64 65 66; 65 66 67; 66 67 68;
67 68 69; 68 69 70; 69 70 71; 70 71 72; 71 72 73; 72 73 74; 73 75 76; 74 76 77;
75 77 78; 76 78 79; 77 79 80; 78 80 81; 79 81 82; 80 82 83; 81 83 84; 82 84 85;
83 85 86; 84 86 87; 85 87 88; 86 88 89; 87 89 90; 88 90 91; 89 91 92; 90 92 93;
91 93 94; 92 94 95; 93 95 96; 94 96 97; 95 97 98; 96 98 99; 97 99 100;
98 100 101; 99 101 102; 100 102 103; 101 103 104; 102 104 105; 103 105 106;
104 106 107; 105 107 108; 106 108 109; 107 109 110; 108 110 111; 109 112 113;
110 113 114; 111 114 115; 112 115 116; 113 116 117; 114 117 118; 115 118 119;
116 119 120; 117 120 121; 118 121 122; 119 122 123; 120 123 124; 121 124 125;
122 125 126; 123 126 127; 124 127 128; 125 128 129; 126 129 130; 127 130 131;
128 131 132; 129 132 133; 130 133 134; 131 134 135; 132 135 136; 133 136 137;
134 137 138; 135 138 139; 136 139 140; 137 140 141; 138 141 142; 139 142 143;
140 143 144; 141 144 145; 142 145 146; 143 146 147; 144 147 148; 145 149 150;
146 150 151; 147 151 152; 148 152 153; 149 153 154; 150 154 155; 151 155 156;
152 156 157; 153 157 158; 154 158 159; 155 159 160; 156 160 161; 157 161 162;
158 162 163; 159 163 164; 160 164 165; 161 165 166; 162 166 167; 163 167 168;
164 168 169; 165 169 170; 166 170 171; 167 171 172; 168 172 173; 169 173 174;
170 174 175; 171 175 176; 172 176 177; 173 177 178; 174 178 179; 175 179 180;
176 180 181; 177 181 182; 178 182 183; 179 183 184; 180 184 185; 181 186 187;
182 187 188; 183 188 189; 184 189 190; 185 190 191; 186 191 192; 187 192 193;
188 193 194; 189 194 195; 190 195 196; 191 196 197; 192 197 198; 193 198 199;
194 199 200; 195 200 201; 196 201 202; 197 202 203; 198 203 204; 199 204 205;
200 205 206; 201 206 207; 202 207 208; 203 208 209; 204 209 210; 205 210 211;
206 211 212; 207 212 213; 208 213 214; 209 214 215; 210 215 216; 211 216 217;
212 217 218; 213 218 219; 214 219 220; 215 220 221; 216 221 222; 217 223 224;
218 224 225; 219 225 226; 220 226 227; 221 227 228; 222 228 229; 223 229 230;
224 230 231; 225 231 232; 226 232 233; 227 233 234; 228 234 235; 229 235 236;
230 236 237; 231 237 238; 232 238 239; 233 239 240; 234 240 241; 235 241 242;
236 242 243; 237 243 244; 238 244 245; 239 245 246; 240 246 247; 241 247 248;
242 248 249; 243 249 250; 244 250 251; 245 251 252; 246 252 253; 247 253 254;
248 254 255; 249 255 256; 250 256 257; 251 257 258; 252 258 259; 253 260 261;
254 261 262; 255 262 263; 256 263 264; 257 264 265; 258 265 266; 259 266 267;
260 267 268; 261 268 269; 262 269 270; 263 270 271; 264 271 272; 265 272 273;
266 273 274; 267 274 275; 268 275 276; 269 276 277; 270 277 278; 271 278 279;
272 279 280; 273 280 281; 274 281 282; 275 282 283; 276 283 284; 277 284 285;
278 285 286; 279 286 287; 280 287 288; 281 288 289; 282 289 290; 283 290 291;
284 291 292; 285 292 293; 286 293 294; 287 294 295; 288 295 296; 301 1 38;
Page 131 of 156
302 38 75; 303 75 112; 304 112 149; 305 149 186; 306 186 223; 307 223 260;
308 2 39; 309 39 76; 310 76 113; 311 113 150; 312 150 187; 313 187 224;
314 224 261; 315 3 40; 316 40 77; 317 77 114; 318 114 151; 319 151 188;
320 188 225; 321 225 262; 322 4 41; 323 41 78; 324 78 115; 325 115 152;
326 152 189; 327 189 226; 328 226 263; 329 5 42; 330 42 79; 331 79 116;
332 116 153; 333 153 190; 334 190 227; 335 227 264; 336 6 43; 337 43 80;
338 80 117; 339 117 154; 340 154 191; 341 191 228; 342 228 265; 343 7 44;
344 44 81; 345 81 118; 346 118 155; 347 155 192; 348 192 229; 349 229 266;
350 8 45; 351 45 82; 352 82 119; 353 119 156; 354 156 193; 355 193 230;
356 230 267; 357 9 46; 358 46 83; 359 83 120; 360 120 157; 361 157 194;
362 194 231; 363 231 268; 364 10 47; 365 47 84; 366 84 121; 367 121 158;
368 158 195; 369 195 232; 370 232 269; 371 11 48; 372 48 85; 373 85 122;
374 122 159; 375 159 196; 376 196 233; 377 233 270; 378 12 49; 379 49 86;
380 86 123; 381 123 160; 382 160 197; 383 197 234; 384 234 271; 385 13 50;
386 50 87; 387 87 124; 388 124 161; 389 161 198; 390 198 235; 391 235 272;
392 14 51; 393 51 88; 394 88 125; 395 125 162; 396 162 199; 397 199 236;
398 236 273; 399 15 52; 400 52 89; 401 89 126; 402 126 163; 403 163 200;
404 200 237; 405 237 274; 406 16 53; 407 53 90; 408 90 127; 409 127 164;
410 164 201; 411 201 238; 412 238 275; 413 17 54; 414 54 91; 415 91 128;
416 128 165; 417 165 202; 418 202 239; 419 239 276; 420 18 55; 421 55 92;
422 92 129; 423 129 166; 424 166 203; 425 203 240; 426 240 277; 427 19 56;
428 56 93; 429 93 130; 430 130 167; 431 167 204; 432 204 241; 433 241 278;
434 20 57; 435 57 94; 436 94 131; 437 131 168; 438 168 205; 439 205 242;
440 242 279; 441 21 58; 442 58 95; 443 95 132; 444 132 169; 445 169 206;
446 206 243; 447 243 280; 448 22 59; 449 59 96; 450 96 133; 451 133 170;
452 170 207; 453 207 244; 454 244 281; 455 23 60; 456 60 97; 457 97 134;
458 134 171; 459 171 208; 460 208 245; 461 245 282; 462 24 61; 463 61 98;
464 98 135; 465 135 172; 466 172 209; 467 209 246; 468 246 283; 469 25 62;
470 62 99; 471 99 136; 472 136 173; 473 173 210; 474 210 247; 475 247 284;
476 26 63; 477 63 100; 478 100 137; 479 137 174; 480 174 211; 481 211 248;
482 248 285; 483 27 64; 484 64 101; 485 101 138; 486 138 175; 487 175 212;
488 212 249; 489 249 286; 490 28 65; 491 65 102; 492 102 139; 493 139 176;
494 176 213; 495 213 250; 496 250 287; 497 29 66; 498 66 103; 499 103 140;
500 140 177; 501 177 214; 502 214 251; 503 251 288; 504 30 67; 505 67 104;
506 104 141; 507 141 178; 508 178 215; 509 215 252; 510 252 289; 511 31 68;
512 68 105; 513 105 142; 514 142 179; 515 179 216; 516 216 253; 517 253 290;
518 32 69; 519 69 106; 520 106 143; 521 143 180; 522 180 217; 523 217 254;
524 254 291; 525 33 70; 526 70 107; 527 107 144; 528 144 181; 529 181 218;
530 218 255; 531 255 292; 532 34 71; 533 71 108; 534 108 145; 535 145 182;
536 182 219; 537 219 256; 538 256 293; 539 35 72; 540 72 109; 541 109 146;
542 146 183; 543 183 220; 544 220 257; 545 257 294; 546 36 73; 547 73 110;
548 110 147; 549 147 184; 550 184 221; 551 221 258; 552 258 295; 553 37 74;
554 74 111; 555 111 148; 556 148 185; 557 185 222; 558 222 259; 559 259 296;
601 5 301; 602 6 302; 603 7 303; 604 8 304; 605 14 305; 606 15 306; 607 16 307;
608 17 308; 609 21 309; 610 22 310; 611 23 311; 612 24 312; 613 30 313;
614 31 314; 615 32 315; 616 33 316; 617 264 317; 618 265 318; 619 266 319;
620 267 320; 621 273 321; 622 274 322; 623 275 323; 624 276 324; 625 280 325;
626 281 326; 627 282 327; 628 283 328; 629 289 329; 630 290 330; 631 291 331;
632 292 332; 633 301 372; 634 302 371; 635 303 370; 636 304 369; 637 305 369;
638 306 370; 639 307 371; 640 308 372; 641 309 376; 642 310 375; 643 311 374;
644 312 373; 645 313 373; 646 314 374; 647 315 375; 648 316 376; 649 317 380;
650 318 379; 651 319 378; 652 320 377; 653 321 377; 654 322 378; 655 323 379;
656 324 380; 657 325 384; 658 326 383; 659 327 382; 660 328 381; 661 329 381;
662 330 382; 663 331 383; 664 332 384; 665 349 350; 666 350 333; 667 333 334;
668 334 335; 669 335 351; 670 351 336; 671 336 352; 672 352 353; 673 354 355;
674 355 337; 675 337 338; 676 338 339; 677 339 356; 678 356 340; 679 340 357;
680 357 358; 681 359 360; 682 360 341; 683 341 342; 684 342 343; 685 343 361;
686 361 344; 687 344 362; 688 362 363; 689 364 365; 690 365 345; 691 345 346;
692 346 347; 693 347 366; 694 366 348; 695 348 367; 696 367 368; 697 351 361;
698 356 366; 699 333 369; 700 334 370; 701 335 371; 702 336 372; 703 337 373;
704 338 374; 705 339 375; 706 340 376; 707 341 377; 708 342 378; 709 343 379;
710 344 380; 711 345 381; 712 346 382; 713 347 383; 714 348 384;
*FOR PERMANENT LOADS
IZ 0.048
42 67 222 247 PRI AX 0.0761 IX 0.000001 IY 0.005 IZ 0.047
43 44 65 66 223 224 245 246 PRI AX 0.0739 IX 0.000001 IY 0.004 IZ 0.045
45 64 225 244 PRI AX 0.0703 IX 0.000001 IY 0.002 IZ 0.043
46 47 62 63 226 227 242 243 PRI AX 0.07 IX 0.000001 IY 0.002 IZ 0.043
48 61 228 241 PRI AX 0.0735 IX 0.000001 IY 0.004 IZ 0.045
49 50 59 60 229 230 239 240 PRI AX 0.0771 IX 0.000001 IY 0.005 IZ 0.047
Page 132 of 156
51 52 57 58 231 232 237 238 PRI AX 0.0786 IX 0.000001 IY 0.006 IZ 0.048
73 TO 77 109 TO 113 145 TO 149 181 TO 185 104 TO 108 140 TO 144 176 TO 180 -
212 TO 216 PRI AX 0.0823 IX 0.000001 IY 0.009 IZ 0.05
78 114 150 186 103 139 175 211 PRI AX 0.0798 IX 0.000001 IY 0.007 IZ 0.049
79 80 115 116 151 152 187 188 102 101 138 137 174 173 210 209 PRI AX 0.0772 -
IX 0.000001 IY 0.005 IZ 0.047
81 117 153 189 100 136 172 208 PRI AX 0.0732 IX 0.000001 IY 0.003 IZ 0.045
82 83 118 119 154 155 190 191 99 98 135 134 171 170 207 206 PRI AX 0.0728 -
IX 0.000001 IY 0.003 IZ 0.045
84 120 156 192 97 133 169 205 PRI AX 0.0768 IX 0.000001 IY 0.005 IZ 0.047
85 86 121 122 157 158 193 194 96 95 132 131 168 167 204 203 PRI AX 0.0809 -
IX 0.000001 IY 0.008 IZ 0.049
87 88 123 124 159 160 195 196 94 93 130 129 166 165 202 201 PRI AX 0.0826 -
IX 0.000001 IY 0.01 IZ 0.05
89 90 125 126 161 162 197 198 92 91 128 127 164 163 200 199 PRI AX 0.0844 -
IX 0.000001 IY 0.012 IZ 0.051
301 307 553 559 PRI AX 0.021 IX 0.000001 IY 0.00415 IZ 0.0001
302 to 306 372 to 376 484 to 488 554 TO 558 PRI AX 0.035 IX 0.000001 IY -
0.00031 IZ 0.013
308 to 328 357 to 371 377 to 391 420 to 440 469 to 483 489 to 503 532 to 552 -
PRI AX 0.0335 IX 0.000001 IY 0.01735 IZ 0.0001
329 to 356 392 to 419 441 to 468 504 to 531 PRI AX 0.026 IX 0.000001 IY -
0.00009 IZ 0.0079
601 TO 632 PRI AX 0.028 IX 0.000001 IY 0.000001 IZ 0.0071
633 TO 664 PRI AX 0.00056 IX 0.000001 IY 0.000000025 IZ 0.000000025
665 673 681 689 TAPERED 1.5 0.4 1.743 0.8 0.4 0.8 0.4
666 674 682 690 TAPERED 1.743 0.4 2.052 0.8 0.4 0.8 0.4
667 675 683 691 699 703 707 711 TAPERED 2.052 0.4 2.185 0.8 0.4 0.8 0.4
668 676 684 692 700 704 708 712 TAPERED 2.185 0.4 2.318 0.8 0.4 0.8 0.4
669 677 685 693 701 705 709 713 TAPERED 2.318 0.4 2.385 0.8 0.4 0.8 0.4
670 678 686 694 702 706 710 714 TAPERED 2.385 0.4 2.415 0.8 0.4 0.8 0.4
671 679 687 695 TAPERED 2.415 0.4 2.5084 0.8 0.4 0.8 0.4
672 680 688 696 TAPERED 2.5084 0.4 3 0.8 0.4 0.8 0.4
697 698 PRIS YD 1 ZD 0.6
ISOTROPIC MATERIAL1
E 2.11e+007
POISSON 0.3
DENSITY 7.85
ISOTROPIC CONCRETE
E 3.2e+006
POISSON 0.17
DENSITY 2.5
ALPHA 1e-005
DAMP 0.05
END DEFINE MATERIAL
CONSTANTS
SUPPORTS
*122 159 PINNED
38 75 112 149 186 223 FIXED BUT FX FZ MX MY MZ
48 64 74 FIXED BUT FX MX MY MZ
85 101 111 FIXED BUT FX FZ MX MY MZ
122 PINNED
159 PINNED
175 185 196 212 222 233 249 259 FIXED BUT FX FZ MX MY MZ
349 354 359 364 FIXED
*333 TO 348 FIXED BUT FX FZ MX MY MZ
MEMBER RELEASE
LOAD 1 SUPP 1 AND 3
SUPPORT DISPLACEMENT LOAD
38 64 75 101 112 138 149 175 186 212 223 249 354 364 FY -0.01
LOAD 2 SUPP 2 & 3
SUPPORT DISPLACEMENT LOAD
Page 133 of 156
48 64 85 101 122 138 159 175 196 212 233 249 349 354 359 364 FY -0.01
PERFORM ANALYSIS
PRINT MEMBER FORCES LIST 37 TO 54 73 TO 90 109 TO 126 145 TO 162 181 TO 198 -
216 TO 234
PRINT MEMBER FORCES LIST 301 TO 307 329 TO 356 371 TO 377 392 TO 419 -
441 TO 468 483 TO 489 504 TO 531 553 TO 559
PRINT MEMBER FORCES LIST 633 TO 664
FINISH
Page 134 of 156

DIFFERENTIAL SHRINAKGE
51 52 57 58 231 232 237 238 PRI AX 0.0786 IX 0.000001 IY 0.006 IZ 0.048

73 TO 77 109 TO 113 145 TO 149 181 TO 185 104 TO 108 140 TO 144 176 TO 180 -
212 TO 216 PRI AX 0.0823 IX 0.000001 IY 0.009 IZ 0.05
78 114 150 186 103 139 175 211 PRI AX 0.0798 IX 0.000001 IY 0.007 IZ 0.049
79 80 115 116 151 152 187 188 102 101 138 137 174 173 210 209 PRI AX 0.0772 -
IX 0.000001 IY 0.005 IZ 0.047
81 117 153 189 100 136 172 208 PRI AX 0.0732 IX 0.000001 IY 0.003 IZ 0.045
82 83 118 119 154 155 190 191 99 98 135 134 171 170 207 206 PRI AX 0.0728 -
IX 0.000001 IY 0.003 IZ 0.045
84 120 156 192 97 133 169 205 PRI AX 0.0768 IX 0.000001 IY 0.005 IZ 0.047
85 86 121 122 157 158 193 194 96 95 132 131 168 167 204 203 PRI AX 0.0809 -
IX 0.000001 IY 0.008 IZ 0.049
87 88 123 124 159 160 195 196 94 93 130 129 166 165 202 201 PRI AX 0.0826 -
IX 0.000001 IY 0.01 IZ 0.05
89 90 125 126 161 162 197 198 92 91 128 127 164 163 200 199 PRI AX 0.0844 -
IX 0.000001 IY 0.012 IZ 0.051
301 307 553 559 PRI AX 0.021 IX 0.000001 IY 0.00415 IZ 0.0001
0.00031 IZ 0.013
308 to 328 357 to 371 377 to 391 420 to 440 469 to 483 489 to 503 532 to 552 -
PRI AX 0.0335 IX 0.000001 IY 0.01735 IZ 0.0001
0.00009 IZ 0.0079
601 TO 632 PRI AX 0.028 IX 0.000001 IY 0.000001 IZ 0.0071
633 TO 664 PRI AX 0.00056 IX 0.000001 IY 0.000000025 IZ 0.000000025
665 673 681 689 TAPERED 1.5 0.4 1.743 0.8 0.4 0.8 0.4
666 674 682 690 TAPERED 1.743 0.4 2.052 0.8 0.4 0.8 0.4
667 675 683 691 699 703 707 711 TAPERED 2.052 0.4 2.185 0.8 0.4 0.8 0.4
668 676 684 692 700 704 708 712 TAPERED 2.185 0.4 2.318 0.8 0.4 0.8 0.4
669 677 685 693 701 705 709 713 TAPERED 2.318 0.4 2.385 0.8 0.4 0.8 0.4
670 678 686 694 702 706 710 714 TAPERED 2.385 0.4 2.415 0.8 0.4 0.8 0.4
671 679 687 695 TAPERED 2.415 0.4 2.5084 0.8 0.4 0.8 0.4
672 680 688 696 TAPERED 2.5084 0.4 3 0.8 0.4 0.8 0.4
697 698 PRIS YD 1 ZD 0.6
ISOTROPIC MATERIAL1
E 2.11e+007
POISSON 0.3
DENSITY 7.85
ISOTROPIC CONCRETE
E 3.2e+006
POISSON 0.17
DENSITY 2.5
ALPHA 1e-005
DAMP 0.05
END DEFINE MATERIAL
CONSTANTS
SUPPORTS
*122 159 PINNED
122 PINNED
159 PINNED
349 354 359 364 FIXED
MEMBER RELEASE
LOAD 1 DIFF SHRINKAGE
JOINT LOAD
38 223 MZ -34.3
74 259 MZ 34.3
75 112 149 186 MZ -41
Page 135 of 156
111 148 185 222 MZ 41
PERFORM ANALYSIS
216 TO 234
441 TO 468 483 TO 489 504 TO 531 553 TO 559
FINISH
Page 136 of 156

FOOTPATH LIVE LOAD
51 52 57 58 231 232 237 238 PRI AX 0.1028 IX 0.000001 IY 0.012 IZ 0.058

73 TO 77 109 TO 113 145 TO 149 181 TO 185 104 TO 108 140 TO 144 176 TO 180 -
212 TO 216 PRI AX 0.11 IX 0.000001 IY 0.018 IZ 0.06
78 114 150 186 103 139 175 211 PRI AX 0.105 IX 0.000001 IY 0.013 IZ 0.059
79 80 115 116 151 152 187 188 102 101 138 137 174 173 210 209 PRI AX 0.1 -
IX 0.000001 IY 0.01 IZ 0.057
81 117 153 189 100 136 172 208 PRI AX 0.0919 IX 0.000001 IY 0.006 IZ 0.054
82 83 118 119 154 155 190 191 99 98 135 134 171 170 207 206 PRI AX 0.0911 -
IX 0.000001 IY 0.005 IZ 0.054
84 120 156 192 97 133 169 205 PRI AX 0.0992 IX 0.000001 IY 0.009 IZ 0.057
85 86 121 122 157 158 193 194 96 95 132 131 168 167 204 203 PRI AX 0.1073 -
IX 0.000001 IY 0.015 IZ 0.059
87 88 123 124 159 160 195 196 94 93 130 129 166 165 202 201 PRI AX 0.1108 -
IX 0.000001 IY 0.018 IZ 0.06
89 90 125 126 161 162 197 198 92 91 128 127 164 163 200 199 PRI AX 0.1143 -
IX 0.000001 IY 0.022 IZ 0.061
301 307 553 559 PRI AX 0.041 IX 0.000001 IY 0.0083 IZ 0.0001
IY 0.00053 IZ 0.0161
308 to 328 357 to 371 377 to 391 420 to 440 469 to 483 489 to 503 532 to 552 -
PRI AX 0.067 IX 0.000001 IY 0.0347 IZ 0.0002
IY 0.00009 IZ 0.0079
601 TO 632 PRI AX 0.1 IX 0.000001 IY 0.01 IZ 0.01
633 TO 664 PRI AX 0.00056 IX 0.000001 IY 0.000000025 IZ 0.000000025
665 673 681 689 TAPERED 1.5 0.4 1.743 0.8 0.4 0.8 0.4
666 674 682 690 TAPERED 1.743 0.4 2.052 0.8 0.4 0.8 0.4
667 675 683 691 699 703 707 711 TAPERED 2.052 0.4 2.185 0.8 0.4 0.8 0.4
668 676 684 692 700 704 708 712 TAPERED 2.185 0.4 2.318 0.8 0.4 0.8 0.4
669 677 685 693 701 705 709 713 TAPERED 2.318 0.4 2.385 0.8 0.4 0.8 0.4
670 678 686 694 702 706 710 714 TAPERED 2.385 0.4 2.415 0.8 0.4 0.8 0.4
671 679 687 695 TAPERED 2.415 0.4 2.5084 0.8 0.4 0.8 0.4
672 680 688 696 TAPERED 2.5084 0.4 3 0.8 0.4 0.8 0.4
697 698 PRIS YD 1 ZD 0.6
ISOTROPIC MATERIAL1
E 2.11e+007
POISSON 0.3
DENSITY 7.85
ALPHA 1.2e-005
ISOTROPIC CONCRETE
E 3.2e+006
POISSON 0.17
DENSITY 2.5
ALPHA 1e-005
DAMP 0.05
END DEFINE MATERIAL
CONSTANTS
SUPPORTS
122 159 PINNED
349 354 359 364 FIXED
MEMBER RELEASE
LOAD 1 FPLL
MEMBER LOAD
180 TO 216 UNI Y -0.144
Page 137 of 156
217 TO 252 UNI Y -0.246
PERFORM ANALYSIS
216 TO 234
441 TO 468 483 TO 489 504 TO 531 553 TO 559
FINISH
Page 138 of 156

PRESTRESS LOAD
51 52 57 58 231 232 237 238 PRI AX 0.1028 IX 0.000001 IY 0.012 IZ 0.058

73 TO 77 109 TO 113 145 TO 149 181 TO 185 104 TO 108 140 TO 144 176 TO 180 -
212 TO 216 PRI AX 0.11 IX 0.000001 IY 0.018 IZ 0.06
78 114 150 186 103 139 175 211 PRI AX 0.105 IX 0.000001 IY 0.013 IZ 0.059
79 80 115 116 151 152 187 188 102 101 138 137 174 173 210 209 PRI AX 0.1 -
IX 0.000001 IY 0.01 IZ 0.057
81 117 153 189 100 136 172 208 PRI AX 0.0919 IX 0.000001 IY 0.006 IZ 0.054
82 83 118 119 154 155 190 191 99 98 135 134 171 170 207 206 PRI AX 0.0911 -
IX 0.000001 IY 0.005 IZ 0.054
84 120 156 192 97 133 169 205 PRI AX 0.0992 IX 0.000001 IY 0.009 IZ 0.057
85 86 121 122 157 158 193 194 96 95 132 131 168 167 204 203 PRI AX 0.1073 -
IX 0.000001 IY 0.015 IZ 0.059
87 88 123 124 159 160 195 196 94 93 130 129 166 165 202 201 PRI AX 0.1108 -
IX 0.000001 IY 0.018 IZ 0.06
89 90 125 126 161 162 197 198 92 91 128 127 164 163 200 199 PRI AX 0.1143 -
IX 0.000001 IY 0.022 IZ 0.061
301 307 553 559 PRI AX 0.041 IX 0.000001 IY 0.0083 IZ 0.0001
IY 0.00053 IZ 0.0161
308 to 328 357 to 371 377 to 391 420 to 440 469 to 483 489 to 503 532 to 552 -
PRI AX 0.067 IX 0.000001 IY 0.0347 IZ 0.0002
IY 0.00009 IZ 0.0079
601 TO 632 PRI AX 0.1 IX 0.000001 IY 0.01 IZ 0.01
633 TO 664 PRI AX 0.00056 IX 0.000001 IY 0.000000025 IZ 0.000000025
665 673 681 689 TAPERED 1.5 0.4 1.743 0.8 0.4 0.8 0.4
666 674 682 690 TAPERED 1.743 0.4 2.052 0.8 0.4 0.8 0.4
667 675 683 691 699 703 707 711 TAPERED 2.052 0.4 2.185 0.8 0.4 0.8 0.4
668 676 684 692 700 704 708 712 TAPERED 2.185 0.4 2.318 0.8 0.4 0.8 0.4
669 677 685 693 701 705 709 713 TAPERED 2.318 0.4 2.385 0.8 0.4 0.8 0.4
670 678 686 694 702 706 710 714 TAPERED 2.385 0.4 2.415 0.8 0.4 0.8 0.4
671 679 687 695 TAPERED 2.415 0.4 2.5084 0.8 0.4 0.8 0.4
672 680 688 696 TAPERED 2.5084 0.4 3 0.8 0.4 0.8 0.4
697 698 PRIS YD 1 ZD 0.6
ISOTROPIC MATERIAL1
E 2.11e+007
POISSON 0.3
DENSITY 7.85
ISOTROPIC CONCRETE
E 3.2e+006
POISSON 0.17
DENSITY 2.5
ALPHA 1.2e-005
DAMP 0.05
END DEFINE MATERIAL
CONSTANTS
SUPPORTS
*122 159 PINNED
122 PINNED
159 PINNED
349 354 359 364 FIXED
MEMBER RELEASE
LOAD 1 PRESTRESS
TEMP LOAD
*STRAIN =10 T /(560*1E-6*2.11E7)= 8.463E-4
633 640 641 648 649 656 657 664 STRAINRATE -8.463E-4
LOAD 2 PRESTRESS
Page 139 of 156
TEMP LOAD
634 639 642 647 650 655 658 663 STRAINRATE -8.463E-4
LOAD 3 PRESTRESS
TEMP LOAD
635 638 643 646 651 654 659 662 STRAINRATE -8.463E-4
LOAD 4 PRESTRESS
TEMP LOAD
636 637 644 645 652 653 660 661 STRAINRATE -8.463E-4
PERFORM ANALYSIS
216 TO 234
441 TO 468 483 TO 489 504 TO 531 553 TO 559
FINISH
Page 140 of 156

STAAD SPACE 25M SPAN (SIDL)
ENGINEER DATE 30-Nov-13
END JOB INFORMATION
INPUT WIDTH 79
PAGE LENGTH 15000
UNIT METER MTON
JOINT COORDINATES
1 0 0 0.175; 2 1.9 0 0.175; 3 4.4 0 0.175; 4 6.9 0 0.175; 5 9.4 0 0.175;
6 11.9 0 0.175; 7 14.4 0 0.175; 8 16.9 0 0.175; 9 19.4 0 0.175;
10 21.9 0 0.175; 11 24.4 0 0.175; 12 26.9 0 0.175; 13 29.4 0 0.175;
14 31.9 0 0.175; 15 34.4 0 0.175; 16 36.9 0 0.175; 17 39.4 0 0.175;
18 41.9 0 0.175; 19 44.4 0 0.175; 20 46.9 0 0.175; 21 49.4 0 0.175;
22 51.9 0 0.175; 23 54.4 0 0.175; 24 56.9 0 0.175; 25 59.4 0 0.175;
26 61.9 0 0.175; 27 64.4 0 0.175; 28 66.9 0 0.175; 29 69.4 0 0.175;
30 71.9 0 0.175; 31 74.4 0 0.175; 32 76.9 0 0.175; 33 79.4 0 0.175;
34 81.9 0 0.175; 35 84.4 0 0.175; 36 86.9 0 0.175; 37 88.8 0 0.175; 38 0 0 0;
39 1.9 0 0; 40 4.4 0 0; 41 6.9 0 0; 42 9.4 0 0; 43 11.9 0 0; 44 14.4 0 0;
45 16.9 0 0; 46 19.4 0 0; 47 21.9 0 0; 48 24.4 0 0; 49 26.9 0 0; 50 29.4 0 0;
51 31.9 0 0; 52 34.4 0 0; 53 36.9 0 0; 54 39.4 0 0; 55 41.9 0 0; 56 44.4 0 0;
57 46.9 0 0; 58 49.4 0 0; 59 51.9 0 0; 60 54.4 0 0; 61 56.9 0 0; 62 59.4 0 0;
63 61.9 0 0; 64 64.4 0 0; 65 66.9 0 0; 66 69.4 0 0; 67 71.9 0 0; 68 74.4 0 0;
69 76.9 0 0; 70 79.4 0 0; 71 81.9 0 0; 72 84.4 0 0; 73 86.9 0 0; 74 88.8 0 0;
75 0 0 -2.24; 76 1.9 0 -2.24; 77 4.4 0 -2.24; 78 6.9 0 -2.24; 79 9.4 0 -2.24;
80 11.9 0 -2.24; 81 14.4 0 -2.24; 82 16.9 0 -2.24; 83 19.4 0 -2.24;
84 21.9 0 -2.24; 85 24.4 0 -2.24; 86 26.9 0 -2.24; 87 29.4 0 -2.24;
88 31.9 0 -2.24; 89 34.4 0 -2.24; 90 36.9 0 -2.24; 91 39.4 0 -2.24;
92 41.9 0 -2.24; 93 44.4 0 -2.24; 94 46.9 0 -2.24; 95 49.4 0 -2.24;
96 51.9 0 -2.24; 97 54.4 0 -2.24; 98 56.9 0 -2.24; 99 59.4 0 -2.24;
100 61.9 0 -2.24; 101 64.4 0 -2.24; 102 66.9 0 -2.24; 103 69.4 0 -2.24;
104 71.9 0 -2.24; 105 74.4 0 -2.24; 106 76.9 0 -2.24; 107 79.4 0 -2.24;
108 81.9 0 -2.24; 109 84.4 0 -2.24; 110 86.9 0 -2.24; 111 88.8 0 -2.24;
112 0 0 -4.48; 113 1.9 0 -4.48; 114 4.4 0 -4.48; 115 6.9 0 -4.48;
116 9.4 0 -4.48; 117 11.9 0 -4.48; 118 14.4 0 -4.48; 119 16.9 0 -4.48;
120 19.4 0 -4.48; 121 21.9 0 -4.48; 122 24.4 0 -4.48; 123 26.9 0 -4.48;
124 29.4 0 -4.48; 125 31.9 0 -4.48; 126 34.4 0 -4.48; 127 36.9 0 -4.48;
128 39.4 0 -4.48; 129 41.9 0 -4.48; 130 44.4 0 -4.48; 131 46.9 0 -4.48;
132 49.4 0 -4.48; 133 51.9 0 -4.48; 134 54.4 0 -4.48; 135 56.9 0 -4.48;
136 59.4 0 -4.48; 137 61.9 0 -4.48; 138 64.4 0 -4.48; 139 66.9 0 -4.48;
140 69.4 0 -4.48; 141 71.9 0 -4.48; 142 74.4 0 -4.48; 143 76.9 0 -4.48;
144 79.4 0 -4.48; 145 81.9 0 -4.48; 146 84.4 0 -4.48; 147 86.9 0 -4.48;
148 88.8 0 -4.48; 149 0 0 -6.72; 150 1.9 0 -6.72; 151 4.4 0 -6.72;
152 6.9 0 -6.72; 153 9.4 0 -6.72; 154 11.9 0 -6.72; 155 14.4 0 -6.72;
156 16.9 0 -6.72; 157 19.4 0 -6.72; 158 21.9 0 -6.72; 159 24.4 0 -6.72;
160 26.9 0 -6.72; 161 29.4 0 -6.72; 162 31.9 0 -6.72; 163 34.4 0 -6.72;
164 36.9 0 -6.72; 165 39.4 0 -6.72; 166 41.9 0 -6.72; 167 44.4 0 -6.72;
168 46.9 0 -6.72; 169 49.4 0 -6.72; 170 51.9 0 -6.72; 171 54.4 0 -6.72;
172 56.9 0 -6.72; 173 59.4 0 -6.72; 174 61.9 0 -6.72; 175 64.4 0 -6.72;
176 66.9 0 -6.72; 177 69.4 0 -6.72; 178 71.9 0 -6.72; 179 74.4 0 -6.72;
180 76.9 0 -6.72; 181 79.4 0 -6.72; 182 81.9 0 -6.72; 183 84.4 0 -6.72;
184 86.9 0 -6.72; 185 88.8 0 -6.72; 186 0 0 -8.96; 187 1.9 0 -8.96;
188 4.4 0 -8.96; 189 6.9 0 -8.96; 190 9.4 0 -8.96; 191 11.9 0 -8.96;
192 14.4 0 -8.96; 193 16.9 0 -8.96; 194 19.4 0 -8.96; 195 21.9 0 -8.96;
196 24.4 0 -8.96; 197 26.9 0 -8.96; 198 29.4 0 -8.96; 199 31.9 0 -8.96;
200 34.4 0 -8.96; 201 36.9 0 -8.96; 202 39.4 0 -8.96; 203 41.9 0 -8.96;
204 44.4 0 -8.96; 205 46.9 0 -8.96; 206 49.4 0 -8.96; 207 51.9 0 -8.96;
208 54.4 0 -8.96; 209 56.9 0 -8.96; 210 59.4 0 -8.96; 211 61.9 0 -8.96;
212 64.4 0 -8.96; 213 66.9 0 -8.96; 214 69.4 0 -8.96; 215 71.9 0 -8.96;
216 74.4 0 -8.96; 217 76.9 0 -8.96; 218 79.4 0 -8.96; 219 81.9 0 -8.96;
220 84.4 0 -8.96; 221 86.9 0 -8.96; 222 88.8 0 -8.96; 223 0 0 -11.2;
224 1.9 0 -11.2; 225 4.4 0 -11.2; 226 6.9 0 -11.2; 227 9.4 0 -11.2;
228 11.9 0 -11.2; 229 14.4 0 -11.2; 230 16.9 0 -11.2; 231 19.4 0 -11.2;
232 21.9 0 -11.2; 233 24.4 0 -11.2; 234 26.9 0 -11.2; 235 29.4 0 -11.2;
236 31.9 0 -11.2; 237 34.4 0 -11.2; 238 36.9 0 -11.2; 239 39.4 0 -11.2;
240 41.9 0 -11.2; 241 44.4 0 -11.2; 242 46.9 0 -11.2; 243 49.4 0 -11.2;
244 51.9 0 -11.2; 245 54.4 0 -11.2; 246 56.9 0 -11.2; 247 59.4 0 -11.2;
248 61.9 0 -11.2; 249 64.4 0 -11.2; 250 66.9 0 -11.2; 251 69.4 0 -11.2;
252 71.9 0 -11.2; 253 74.4 0 -11.2; 254 76.9 0 -11.2; 255 79.4 0 -11.2;
256 81.9 0 -11.2; 257 84.4 0 -11.2; 258 86.9 0 -11.2; 259 88.8 0 -11.2;
260 0 0 -11.375; 261 1.9 0 -11.375; 262 4.4 0 -11.375; 263 6.9 0 -11.375;
264 9.4 0 -11.375; 265 11.9 0 -11.375; 266 14.4 0 -11.375; 267 16.9 0 -11.375;
268 19.4 0 -11.375; 269 21.9 0 -11.375; 270 24.4 0 -11.375; 271 26.9 0 -11.375;
272 29.4 0 -11.375; 273 31.9 0 -11.375; 274 34.4 0 -11.375; 275 36.9 0 -11.375;
Page 141 of 156
276 39.4 0 -11.375; 277 41.9 0 -11.375; 278 44.4 0 -11.375; 279 46.9 0 -11.375;
280 49.4 0 -11.375; 281 51.9 0 -11.375; 282 54.4 0 -11.375; 283 56.9 0 -11.375;
284 59.4 0 -11.375; 285 61.9 0 -11.375; 286 64.4 0 -11.375; 287 66.9 0 -11.375;
288 69.4 0 -11.375; 289 71.9 0 -11.375; 290 74.4 0 -11.375; 291 76.9 0 -11.375;
292 79.4 0 -11.375; 293 81.9 0 -11.375; 294 84.4 0 -11.375; 295 86.9 0 -11.375;
296 88.8 0 -11.375; 301 9.4 0 0.55; 302 11.9 0 0.55; 303 14.4 0 0.55;
304 16.9 0 0.55; 305 31.9 0 0.55; 306 34.4 0 0.55; 307 36.9 0 0.55;
308 39.4 0 0.55; 309 49.4 0 0.55; 310 51.9 0 0.55; 311 54.4 0 0.55;
312 56.9 0 0.55; 313 71.9 0 0.55; 314 74.4 0 0.55; 315 76.9 0 0.55;
316 79.4 0 0.55; 317 9.4 0 -11.75; 318 11.9 0 -11.75; 319 14.4 0 -11.75;
320 16.9 0 -11.75; 321 31.9 0 -11.75; 322 34.4 0 -11.75; 323 36.9 0 -11.75;
324 39.4 0 -11.75; 325 49.4 0 -11.75; 326 51.9 0 -11.75; 327 54.4 0 -11.75;
328 56.9 0 -11.75; 329 71.9 0 -11.75; 330 74.4 0 -11.75; 331 76.9 0 -11.75;
332 79.4 0 -11.75; 333 24.4 3 0.55; 334 24.4 4 0.55; 335 24.4 5 0.55;
336 24.4 6 0.55; 337 64.4 3 0.55; 338 64.4 4 0.55; 339 64.4 5 0.55;
340 64.4 6 0.55; 341 24.4 3 -11.75; 342 24.4 4 -11.75; 343 24.4 5 -11.75;
344 24.4 6 -11.75; 345 64.4 3 -11.75; 346 64.4 4 -11.75; 347 64.4 5 -11.75;
348 64.4 6 -11.75; 349 24.4 -1.154 1.23; 350 24.4 0.666 1.23;
351 24.4 5.5 0.55; 352 24.4 7 0.55; 353 24.4 10.09 0.55; 354 64.4 -1.154 1.23;
355 64.4 0.666 1.23; 356 64.4 5.5 0.55; 357 64.4 7 0.55; 358 64.4 10.09 0.55;
359 24.4 -1.154 -12.43; 360 24.4 0.666 -12.43; 361 24.4 5.5 -11.75;
362 24.4 7 -11.75; 363 24.4 10.09 -11.75; 364 64.4 -1.154 -12.43;
365 64.4 0.666 -12.43; 366 64.4 5.5 -11.75; 367 64.4 7 -11.75;
368 64.4 10.09 -11.75; 369 24.4 3.1 0.55; 370 24.4 4.1 0.55; 371 24.4 5.1 0.55;
372 24.4 6.1 0.55; 373 64.4 3.1 0.55; 374 64.4 4.1 0.55; 375 64.4 5.1 0.55;
376 64.4 6.1 0.55; 377 24.4 3.1 -11.75; 378 24.4 4.1 -11.75;
379 24.4 5.1 -11.75; 380 24.4 6.1 -11.75; 381 64.4 3.1 -11.75;
382 64.4 4.1 -11.75; 383 64.4 5.1 -11.75; 384 64.4 6.1 -11.75;
MEMBER INCIDENCES
1 1 2; 2 2 3; 3 3 4; 4 4 5; 5 5 6; 6 6 7; 7 7 8; 8 8 9; 9 9 10; 10 10 11;
11 11 12; 12 12 13; 13 13 14; 14 14 15; 15 15 16; 16 16 17; 17 17 18; 18 18 19;
19 19 20; 20 20 21; 21 21 22; 22 22 23; 23 23 24; 24 24 25; 25 25 26; 26 26 27;
27 27 28; 28 28 29; 29 29 30; 30 30 31; 31 31 32; 32 32 33; 33 33 34; 34 34 35;
35 35 36; 36 36 37; 37 38 39; 38 39 40; 39 40 41; 40 41 42; 41 42 43; 42 43 44;
43 44 45; 44 45 46; 45 46 47; 46 47 48; 47 48 49; 48 49 50; 49 50 51; 50 51 52;
51 52 53; 52 53 54; 53 54 55; 54 55 56; 55 56 57; 56 57 58; 57 58 59; 58 59 60;
59 60 61; 60 61 62; 61 62 63; 62 63 64; 63 64 65; 64 65 66; 65 66 67; 66 67 68;
67 68 69; 68 69 70; 69 70 71; 70 71 72; 71 72 73; 72 73 74; 73 75 76; 74 76 77;
75 77 78; 76 78 79; 77 79 80; 78 80 81; 79 81 82; 80 82 83; 81 83 84; 82 84 85;
83 85 86; 84 86 87; 85 87 88; 86 88 89; 87 89 90; 88 90 91; 89 91 92; 90 92 93;
91 93 94; 92 94 95; 93 95 96; 94 96 97; 95 97 98; 96 98 99; 97 99 100;
98 100 101; 99 101 102; 100 102 103; 101 103 104; 102 104 105; 103 105 106;
104 106 107; 105 107 108; 106 108 109; 107 109 110; 108 110 111; 109 112 113;
110 113 114; 111 114 115; 112 115 116; 113 116 117; 114 117 118; 115 118 119;
116 119 120; 117 120 121; 118 121 122; 119 122 123; 120 123 124; 121 124 125;
122 125 126; 123 126 127; 124 127 128; 125 128 129; 126 129 130; 127 130 131;
128 131 132; 129 132 133; 130 133 134; 131 134 135; 132 135 136; 133 136 137;
134 137 138; 135 138 139; 136 139 140; 137 140 141; 138 141 142; 139 142 143;
140 143 144; 141 144 145; 142 145 146; 143 146 147; 144 147 148; 145 149 150;
146 150 151; 147 151 152; 148 152 153; 149 153 154; 150 154 155; 151 155 156;
152 156 157; 153 157 158; 154 158 159; 155 159 160; 156 160 161; 157 161 162;
158 162 163; 159 163 164; 160 164 165; 161 165 166; 162 166 167; 163 167 168;
164 168 169; 165 169 170; 166 170 171; 167 171 172; 168 172 173; 169 173 174;
170 174 175; 171 175 176; 172 176 177; 173 177 178; 174 178 179; 175 179 180;
176 180 181; 177 181 182; 178 182 183; 179 183 184; 180 184 185; 181 186 187;
182 187 188; 183 188 189; 184 189 190; 185 190 191; 186 191 192; 187 192 193;
188 193 194; 189 194 195; 190 195 196; 191 196 197; 192 197 198; 193 198 199;
194 199 200; 195 200 201; 196 201 202; 197 202 203; 198 203 204; 199 204 205;
200 205 206; 201 206 207; 202 207 208; 203 208 209; 204 209 210; 205 210 211;
206 211 212; 207 212 213; 208 213 214; 209 214 215; 210 215 216; 211 216 217;
212 217 218; 213 218 219; 214 219 220; 215 220 221; 216 221 222; 217 223 224;
218 224 225; 219 225 226; 220 226 227; 221 227 228; 222 228 229; 223 229 230;
224 230 231; 225 231 232; 226 232 233; 227 233 234; 228 234 235; 229 235 236;
230 236 237; 231 237 238; 232 238 239; 233 239 240; 234 240 241; 235 241 242;
236 242 243; 237 243 244; 238 244 245; 239 245 246; 240 246 247; 241 247 248;
242 248 249; 243 249 250; 244 250 251; 245 251 252; 246 252 253; 247 253 254;
248 254 255; 249 255 256; 250 256 257; 251 257 258; 252 258 259; 253 260 261;
254 261 262; 255 262 263; 256 263 264; 257 264 265; 258 265 266; 259 266 267;
260 267 268; 261 268 269; 262 269 270; 263 270 271; 264 271 272; 265 272 273;
266 273 274; 267 274 275; 268 275 276; 269 276 277; 270 277 278; 271 278 279;
272 279 280; 273 280 281; 274 281 282; 275 282 283; 276 283 284; 277 284 285;
278 285 286; 279 286 287; 280 287 288; 281 288 289; 282 289 290; 283 290 291;
284 291 292; 285 292 293; 286 293 294; 287 294 295; 288 295 296; 301 1 38;
Page 142 of 156
302 38 75; 303 75 112; 304 112 149; 305 149 186; 306 186 223; 307 223 260;
308 2 39; 309 39 76; 310 76 113; 311 113 150; 312 150 187; 313 187 224;
314 224 261; 315 3 40; 316 40 77; 317 77 114; 318 114 151; 319 151 188;
320 188 225; 321 225 262; 322 4 41; 323 41 78; 324 78 115; 325 115 152;
326 152 189; 327 189 226; 328 226 263; 329 5 42; 330 42 79; 331 79 116;
332 116 153; 333 153 190; 334 190 227; 335 227 264; 336 6 43; 337 43 80;
338 80 117; 339 117 154; 340 154 191; 341 191 228; 342 228 265; 343 7 44;
344 44 81; 345 81 118; 346 118 155; 347 155 192; 348 192 229; 349 229 266;
350 8 45; 351 45 82; 352 82 119; 353 119 156; 354 156 193; 355 193 230;
356 230 267; 357 9 46; 358 46 83; 359 83 120; 360 120 157; 361 157 194;
362 194 231; 363 231 268; 364 10 47; 365 47 84; 366 84 121; 367 121 158;
368 158 195; 369 195 232; 370 232 269; 371 11 48; 372 48 85; 373 85 122;
374 122 159; 375 159 196; 376 196 233; 377 233 270; 378 12 49; 379 49 86;
380 86 123; 381 123 160; 382 160 197; 383 197 234; 384 234 271; 385 13 50;
386 50 87; 387 87 124; 388 124 161; 389 161 198; 390 198 235; 391 235 272;
392 14 51; 393 51 88; 394 88 125; 395 125 162; 396 162 199; 397 199 236;
398 236 273; 399 15 52; 400 52 89; 401 89 126; 402 126 163; 403 163 200;
404 200 237; 405 237 274; 406 16 53; 407 53 90; 408 90 127; 409 127 164;
410 164 201; 411 201 238; 412 238 275; 413 17 54; 414 54 91; 415 91 128;
416 128 165; 417 165 202; 418 202 239; 419 239 276; 420 18 55; 421 55 92;
422 92 129; 423 129 166; 424 166 203; 425 203 240; 426 240 277; 427 19 56;
428 56 93; 429 93 130; 430 130 167; 431 167 204; 432 204 241; 433 241 278;
434 20 57; 435 57 94; 436 94 131; 437 131 168; 438 168 205; 439 205 242;
440 242 279; 441 21 58; 442 58 95; 443 95 132; 444 132 169; 445 169 206;
446 206 243; 447 243 280; 448 22 59; 449 59 96; 450 96 133; 451 133 170;
452 170 207; 453 207 244; 454 244 281; 455 23 60; 456 60 97; 457 97 134;
458 134 171; 459 171 208; 460 208 245; 461 245 282; 462 24 61; 463 61 98;
464 98 135; 465 135 172; 466 172 209; 467 209 246; 468 246 283; 469 25 62;
470 62 99; 471 99 136; 472 136 173; 473 173 210; 474 210 247; 475 247 284;
476 26 63; 477 63 100; 478 100 137; 479 137 174; 480 174 211; 481 211 248;
482 248 285; 483 27 64; 484 64 101; 485 101 138; 486 138 175; 487 175 212;
488 212 249; 489 249 286; 490 28 65; 491 65 102; 492 102 139; 493 139 176;
494 176 213; 495 213 250; 496 250 287; 497 29 66; 498 66 103; 499 103 140;
500 140 177; 501 177 214; 502 214 251; 503 251 288; 504 30 67; 505 67 104;
506 104 141; 507 141 178; 508 178 215; 509 215 252; 510 252 289; 511 31 68;
512 68 105; 513 105 142; 514 142 179; 515 179 216; 516 216 253; 517 253 290;
518 32 69; 519 69 106; 520 106 143; 521 143 180; 522 180 217; 523 217 254;
524 254 291; 525 33 70; 526 70 107; 527 107 144; 528 144 181; 529 181 218;
530 218 255; 531 255 292; 532 34 71; 533 71 108; 534 108 145; 535 145 182;
536 182 219; 537 219 256; 538 256 293; 539 35 72; 540 72 109; 541 109 146;
542 146 183; 543 183 220; 544 220 257; 545 257 294; 546 36 73; 547 73 110;
548 110 147; 549 147 184; 550 184 221; 551 221 258; 552 258 295; 553 37 74;
554 74 111; 555 111 148; 556 148 185; 557 185 222; 558 222 259; 559 259 296;
601 5 301; 602 6 302; 603 7 303; 604 8 304; 605 14 305; 606 15 306; 607 16 307;
608 17 308; 609 21 309; 610 22 310; 611 23 311; 612 24 312; 613 30 313;
614 31 314; 615 32 315; 616 33 316; 617 264 317; 618 265 318; 619 266 319;
620 267 320; 621 273 321; 622 274 322; 623 275 323; 624 276 324; 625 280 325;
626 281 326; 627 282 327; 628 283 328; 629 289 329; 630 290 330; 631 291 331;
632 292 332; 633 301 372; 634 302 371; 635 303 370; 636 304 369; 637 305 369;
638 306 370; 639 307 371; 640 308 372; 641 309 376; 642 310 375; 643 311 374;
644 312 373; 645 313 373; 646 314 374; 647 315 375; 648 316 376; 649 317 380;
650 318 379; 651 319 378; 652 320 377; 653 321 377; 654 322 378; 655 323 379;
656 324 380; 657 325 384; 658 326 383; 659 327 382; 660 328 381; 661 329 381;
662 330 382; 663 331 383; 664 332 384; 665 349 350; 666 350 333; 667 333 334;
668 334 335; 669 335 351; 670 351 336; 671 336 352; 672 352 353; 673 354 355;
674 355 337; 675 337 338; 676 338 339; 677 339 356; 678 356 340; 679 340 357;
680 357 358; 681 359 360; 682 360 341; 683 341 342; 684 342 343; 685 343 361;
686 361 344; 687 344 362; 688 362 363; 689 364 365; 690 365 345; 691 345 346;
692 346 347; 693 347 366; 694 366 348; 695 348 367; 696 367 368; 697 351 361;
698 356 366; 699 333 369; 700 334 370; 701 335 371; 702 336 372; 703 337 373;
704 338 374; 705 339 375; 706 340 376; 707 341 377; 708 342 378; 709 343 379;
710 344 380; 711 345 381; 712 346 382; 713 347 383; 714 348 384;
*FOR PERMANENT LOADS
IZ 0.048
42 67 222 247 PRI AX 0.0761 IX 0.000001 IY 0.005 IZ 0.047
43 44 65 66 223 224 245 246 PRI AX 0.0739 IX 0.000001 IY 0.004 IZ 0.045
45 64 225 244 PRI AX 0.0703 IX 0.000001 IY 0.002 IZ 0.043
46 47 62 63 226 227 242 243 PRI AX 0.07 IX 0.000001 IY 0.002 IZ 0.043
48 61 228 241 PRI AX 0.0735 IX 0.000001 IY 0.004 IZ 0.045
49 50 59 60 229 230 239 240 PRI AX 0.0771 IX 0.000001 IY 0.005 IZ 0.047
Page 143 of 156
51 52 57 58 231 232 237 238 PRI AX 0.0786 IX 0.000001 IY 0.006 IZ 0.048
73 TO 77 109 TO 113 145 TO 149 181 TO 185 104 TO 108 140 TO 144 176 TO 180 -
212 TO 216 PRI AX 0.0823 IX 0.000001 IY 0.009 IZ 0.05
78 114 150 186 103 139 175 211 PRI AX 0.0798 IX 0.000001 IY 0.007 IZ 0.049
79 80 115 116 151 152 187 188 102 101 138 137 174 173 210 209 PRI AX 0.0772 -
IX 0.000001 IY 0.005 IZ 0.047
81 117 153 189 100 136 172 208 PRI AX 0.0732 IX 0.000001 IY 0.003 IZ 0.045
82 83 118 119 154 155 190 191 99 98 135 134 171 170 207 206 PRI AX 0.0728 -
IX 0.000001 IY 0.003 IZ 0.045
84 120 156 192 97 133 169 205 PRI AX 0.0768 IX 0.000001 IY 0.005 IZ 0.047
85 86 121 122 157 158 193 194 96 95 132 131 168 167 204 203 PRI AX 0.0809 -
IX 0.000001 IY 0.008 IZ 0.049
87 88 123 124 159 160 195 196 94 93 130 129 166 165 202 201 PRI AX 0.0826 -
IX 0.000001 IY 0.01 IZ 0.05
89 90 125 126 161 162 197 198 92 91 128 127 164 163 200 199 PRI AX 0.0844 -
IX 0.000001 IY 0.012 IZ 0.051
301 307 553 559 PRI AX 0.021 IX 0.000001 IY 0.00415 IZ 0.0001
0.00031 IZ 0.013
308 to 328 357 to 371 377 to 391 420 to 440 469 to 483 489 to 503 532 to 552 -
PRI AX 0.0335 IX 0.000001 IY 0.01735 IZ 0.0001
0.00009 IZ 0.0079
601 TO 632 PRI AX 0.028 IX 0.000001 IY 0.000001 IZ 0.0071
633 TO 664 PRI AX 0.00056 IX 0.000001 IY 0.000000025 IZ 0.000000025
665 673 681 689 TAPERED 1.5 0.4 1.743 0.8 0.4 0.8 0.4
666 674 682 690 TAPERED 1.743 0.4 2.052 0.8 0.4 0.8 0.4
667 675 683 691 699 703 707 711 TAPERED 2.052 0.4 2.185 0.8 0.4 0.8 0.4
668 676 684 692 700 704 708 712 TAPERED 2.185 0.4 2.318 0.8 0.4 0.8 0.4
669 677 685 693 701 705 709 713 TAPERED 2.318 0.4 2.385 0.8 0.4 0.8 0.4
670 678 686 694 702 706 710 714 TAPERED 2.385 0.4 2.415 0.8 0.4 0.8 0.4
671 679 687 695 TAPERED 2.415 0.4 2.5084 0.8 0.4 0.8 0.4
672 680 688 696 TAPERED 2.5084 0.4 3 0.8 0.4 0.8 0.4
697 698 PRIS YD 1 ZD 0.6
ISOTROPIC MATERIAL1
E 2.11e+007
POISSON 0.3
DENSITY 7.85
ISOTROPIC CONCRETE
E 3.2e+006
POISSON 0.17
DENSITY 2.5
ALPHA 1.2e-005
DAMP 0.05
END DEFINE MATERIAL
CONSTANTS
SUPPORTS
*122 159 PINNED
122 PINNED
159 PINNED
349 354 359 364 FIXED
MEMBER RELEASE
LOAD 1 SIDL
MEMBER LOAD
1 TO 36 UNI Y -0.75
37 TO 72 UNI Y -0.214
73 TO 180 UNI Y -0.448
Page 144 of 156
181 TO 216 UNI Y -0.969
217 TO 252 UNI Y -0.353
253 TO 288 UNI Y -0.75
PERFORM ANALYSIS
216 TO 234
441 TO 468 483 TO 489 504 TO 531 553 TO 559
PRINT MEMBER FORCES LIST 633 to 664
PRINT JOINT DISPLACEMENTS LIST 43 56 80 93 117 130 154 167 191 204 228 241
FINISH
Page 145 of 156

TEMPERATURE GRADIENT LOAD
51 52 57 58 231 232 237 238 PRI AX 0.1028 IX 0.000001 IY 0.012 IZ 0.058

73 TO 77 109 TO 113 145 TO 149 181 TO 185 104 TO 108 140 TO 144 176 TO 180 -
212 TO 216 PRI AX 0.11 IX 0.000001 IY 0.018 IZ 0.06
78 114 150 186 103 139 175 211 PRI AX 0.105 IX 0.000001 IY 0.013 IZ 0.059
79 80 115 116 151 152 187 188 102 101 138 137 174 173 210 209 PRI AX 0.1 -
IX 0.000001 IY 0.01 IZ 0.057
81 117 153 189 100 136 172 208 PRI AX 0.0919 IX 0.000001 IY 0.006 IZ 0.054
82 83 118 119 154 155 190 191 99 98 135 134 171 170 207 206 PRI AX 0.0911 -
IX 0.000001 IY 0.005 IZ 0.054
84 120 156 192 97 133 169 205 PRI AX 0.0992 IX 0.000001 IY 0.009 IZ 0.057
85 86 121 122 157 158 193 194 96 95 132 131 168 167 204 203 PRI AX 0.1073 -
IX 0.000001 IY 0.015 IZ 0.059
87 88 123 124 159 160 195 196 94 93 130 129 166 165 202 201 PRI AX 0.1108 -
IX 0.000001 IY 0.018 IZ 0.06
89 90 125 126 161 162 197 198 92 91 128 127 164 163 200 199 PRI AX 0.1143 -
IX 0.000001 IY 0.022 IZ 0.061
301 307 553 559 PRI AX 0.041 IX 0.000001 IY 0.0083 IZ 0.0001
IY 0.00053 IZ 0.0161
308 to 328 357 to 371 377 to 391 420 to 440 469 to 483 489 to 503 532 to 552 -
PRI AX 0.067 IX 0.000001 IY 0.0347 IZ 0.0002
IY 0.00009 IZ 0.0079
601 TO 632 PRI AX 0.1 IX 0.000001 IY 0.01 IZ 0.01
633 TO 664 PRI AX 0.00056 IX 0.000001 IY 0.000000025 IZ 0.000000025
665 673 681 689 TAPERED 1.5 0.4 1.743 0.8 0.4 0.8 0.4
666 674 682 690 TAPERED 1.743 0.4 2.052 0.8 0.4 0.8 0.4
667 675 683 691 699 703 707 711 TAPERED 2.052 0.4 2.185 0.8 0.4 0.8 0.4
668 676 684 692 700 704 708 712 TAPERED 2.185 0.4 2.318 0.8 0.4 0.8 0.4
669 677 685 693 701 705 709 713 TAPERED 2.318 0.4 2.385 0.8 0.4 0.8 0.4
670 678 686 694 702 706 710 714 TAPERED 2.385 0.4 2.415 0.8 0.4 0.8 0.4
671 679 687 695 TAPERED 2.415 0.4 2.5084 0.8 0.4 0.8 0.4
672 680 688 696 TAPERED 2.5084 0.4 3 0.8 0.4 0.8 0.4
697 698 PRIS YD 1 ZD 0.6
ISOTROPIC MATERIAL1
E 2.11e+007
POISSON 0.3
DENSITY 7.85
ALPHA 1.2e-005
ISOTROPIC CONCRETE
E 2.21467e+006
POISSON 0.17
DENSITY 2.40262
ALPHA 1e-005
DAMP 0.05
END DEFINE MATERIAL
CONSTANTS
SUPPORTS
122 159 PINNED
349 354 359 364 FIXED
MEMBER RELEASE
LOAD 1 TG RISE
JOINT LOAD
Page 146 of 156
38 223 MZ -79
74 259 MZ 79
75 112 149 186 MZ -81.6
111 148 185 222 MZ 81.6
LOAD 2 TG FALL
JOINT LOAD
38 223 MZ 25.5
74 259 MZ -25.5
75 112 149 186 MZ 26
111 148 185 222 MZ -26
PERFORM ANALYSIS
216 TO 234
441 TO 468 483 TO 489 504 TO 531 553 TO 559
FINISH
Page 147 of 156

UNIFORM TEMP RISE/FALL
51 52 57 58 231 232 237 238 PRIS AX 0.0902 IX 1e-006 IY 0.008 IZ 0.053
53 TO 56 233 TO 236 PRIS AX 0.0925 IX 1e-006 IY 0.01 IZ 0.054
73 TO 77 104 TO 113 140 TO 149 176 TO 185 212 TO 215 -
216 PRIS AX 0.11 IX 1e-006 IY 0.018 IZ 0.06
78 103 114 139 150 175 186 211 PRIS AX 0.105 IX 1e-006 IY 0.013 IZ 0.059
79 80 101 102 115 116 137 138 151 152 173 174 187 188 209 -
210 PRIS AX 0.1 IX 1e-006 IY 0.01 IZ 0.057
81 100 117 136 153 172 189 208 PRIS AX 0.0919 IX 1e-006 IY 0.006 IZ 0.054
82 83 98 99 118 119 134 135 154 155 170 171 190 191 206 -
207 PRIS AX 0.0911 IX 1e-006 IY 0.005 IZ 0.054
84 97 120 133 156 169 192 205 PRIS AX 0.0992 IX 1e-006 IY 0.009 IZ 0.057
85 86 95 96 121 122 131 132 157 158 167 168 193 194 203 -
204 PRIS AX 0.1073 IX 1e-006 IY 0.015 IZ 0.059
87 88 93 94 123 124 129 130 159 160 165 166 195 196 201 -
202 PRIS AX 0.1108 IX 1e-006 IY 0.018 IZ 0.06
89 TO 92 125 TO 128 161 TO 164 197 TO 199 -
200 PRIS AX 0.1143 IX 1e-006 IY 0.022 IZ 0.061
301 307 553 559 PRIS AX 0.041 IX 1e-006 IY 0.0083 IZ 0.0001
302 TO 306 372 TO 376 484 TO 488 554 TO 557 -
558 PRIS AX 0.044 IX 1e-006 IY 0.00053 IZ 0.0161
308 TO 328 357 TO 371 377 TO 391 420 TO 440 469 TO 483 489 TO 503 532 TO 551 -
552 PRIS AX 0.067 IX 1e-006 IY 0.0347 IZ 0.0002
329 TO 356 392 TO 419 441 TO 468 504 TO 530 -
531 PRIS AX 0.026 IX 1e-006 IY 9e-005 IZ 0.0079
601 TO 632 PRIS AX 0.06 IX 1e-006 IY 0.0028125 IZ 0.0018
633 TO 664 PRIS AX 0.00056 IX 1e-006 IY 2.5e-008 IZ 2.5e-008
665 673 681 689 TAPERED 1.5 0.4 1.743 0.8 0.4 0.8 0.4
666 674 682 690 TAPERED 1.743 0.4 2.052 0.8 0.4 0.8 0.4
667 675 683 691 699 703 707 711 TAPERED 2.052 0.4 2.185 0.8 0.4 0.8 0.4
668 676 684 692 700 704 708 712 TAPERED 2.185 0.4 2.318 0.8 0.4 0.8 0.4
669 677 685 693 701 705 709 713 TAPERED 2.318 0.4 2.385 0.8 0.4 0.8 0.4
670 678 686 694 702 706 710 714 TAPERED 2.385 0.4 2.415 0.8 0.4 0.8 0.4
671 679 687 695 TAPERED 2.415 0.4 2.5084 0.8 0.4 0.8 0.4
672 680 688 696 TAPERED 2.5084 0.4 3 0.8 0.4 0.8 0.4
697 698 PRIS YD 1 ZD 0.6
ISOTROPIC MATERIAL1
E 2.11e+007
POISSON 0.3
DENSITY 7.85
ALPHA 1.2e-005
ISOTROPIC CONCRETE
E 2.21467e+006
POISSON 0.17
DENSITY 2.40262
ALPHA 1.2e-005
DAMP 0.05
END DEFINE MATERIAL
CONSTANTS
SUPPORTS
122 159 PINNED
349 354 359 364 FIXED
MEMBER RELEASE
LOAD 1 TEMP RISE
TEMPERATURE LOAD
1 TO 288 633 TO 664 TEMP 36.25
Page 148 of 156
LOAD 2 TEMP FALL
TEMPERATURE LOAD
1 TO 288 633 TO 664 TEMP -31.25
PERFORM ANALYSIS
216 TO 234
441 TO 468 483 TO 489 504 TO 531 553 TO 559
FINISH
Page 149 of 156

SEISMIC TRANS DIRECTION
51 52 57 58 231 232 237 238 PRIS AX 0.0902 IX 1e-006 IY 0.008 IZ 0.053

73 TO 77 104 TO 113 140 TO 149 176 TO 185 212 TO 215 -
216 PRIS AX 0.11 IX 1e-006 IY 0.018 IZ 0.06
78 103 114 139 150 175 186 211 PRIS AX 0.105 IX 1e-006 IY 0.013 IZ 0.059
79 80 101 102 115 116 137 138 151 152 173 174 187 188 209 -
210 PRIS AX 0.1 IX 1e-006 IY 0.01 IZ 0.057
81 100 117 136 153 172 189 208 PRIS AX 0.0919 IX 1e-006 IY 0.006 IZ 0.054
82 83 98 99 118 119 134 135 154 155 170 171 190 191 206 -
207 PRIS AX 0.0911 IX 1e-006 IY 0.005 IZ 0.054
84 97 120 133 156 169 192 205 PRIS AX 0.0992 IX 1e-006 IY 0.009 IZ 0.057
85 86 95 96 121 122 131 132 157 158 167 168 193 194 203 -
204 PRIS AX 0.1073 IX 1e-006 IY 0.015 IZ 0.059
87 88 93 94 123 124 129 130 159 160 165 166 195 196 201 -
202 PRIS AX 0.1108 IX 1e-006 IY 0.018 IZ 0.06
89 TO 92 125 TO 128 161 TO 164 197 TO 199 -
200 PRIS AX 0.1143 IX 1e-006 IY 0.022 IZ 0.061
301 307 553 559 PRIS AX 0.041 IX 1e-006 IY 0.0083 IZ 0.0001
302 TO 306 372 TO 376 484 TO 488 554 TO 557 -
558 PRIS AX 0.044 IX 1e-006 IY 0.00053 IZ 0.0161
308 TO 328 357 TO 371 377 TO 391 420 TO 440 469 TO 483 489 TO 503 532 TO 551 -
552 PRIS AX 0.067 IX 1e-006 IY 0.0347 IZ 0.0002
329 TO 356 392 TO 419 441 TO 468 504 TO 530 -
531 PRIS AX 0.026 IX 1e-006 IY 9e-005 IZ 0.0079
665 673 681 689 TAPERED 1.5 0.4 1.743 0.8 0.4 0.8 0.4
666 674 682 690 TAPERED 1.743 0.4 2.052 0.8 0.4 0.8 0.4
667 675 683 691 699 703 707 711 TAPERED 2.052 0.4 2.185 0.8 0.4 0.8 0.4
668 676 684 692 700 704 708 712 TAPERED 2.185 0.4 2.318 0.8 0.4 0.8 0.4
669 677 685 693 701 705 709 713 TAPERED 2.318 0.4 2.385 0.8 0.4 0.8 0.4
670 678 686 694 702 706 710 714 TAPERED 2.385 0.4 2.415 0.8 0.4 0.8 0.4
671 679 687 695 TAPERED 2.415 0.4 2.5084 0.8 0.4 0.8 0.4
672 680 688 696 TAPERED 2.5084 0.4 3 0.8 0.4 0.8 0.4
697 698 PRIS YD 1 ZD 0.6
ISOTROPIC MATERIAL1
E 2.11e+007
POISSON 0.3
DENSITY 7.85
ALPHA 1.2e-005
ISOTROPIC CONCRETE
E 3.2e+006
POISSON 0.17
DENSITY 2.5
ALPHA 1e-005
DAMP 0.05
END DEFINE MATERIAL
CONSTANTS
SUPPORTS
122 159 PINNED
349 354 359 364 FIXED
MEMBER RELEASE
LOAD 1 SEISMIC TRANS
SELFWEIGHT Z 0.18
PERFORM ANALYSIS
Page 150 of 156
216 TO 234
441 TO 468 483 TO 489 504 TO 531 553 TO 559
FINISH
Page 151 of 156

SEISMIC IN LONG DIRECTION
51 52 57 58 231 232 237 238 PRIS AX 0.0902 IX 1e-006 IY 0.008 IZ 0.053

73 TO 77 104 TO 113 140 TO 149 176 TO 185 212 TO 215 -
216 PRIS AX 0.11 IX 1e-006 IY 0.018 IZ 0.06
78 103 114 139 150 175 186 211 PRIS AX 0.105 IX 1e-006 IY 0.013 IZ 0.059
79 80 101 102 115 116 137 138 151 152 173 174 187 188 209 -
210 PRIS AX 0.1 IX 1e-006 IY 0.01 IZ 0.057
81 100 117 136 153 172 189 208 PRIS AX 0.0919 IX 1e-006 IY 0.006 IZ 0.054
82 83 98 99 118 119 134 135 154 155 170 171 190 191 206 -
207 PRIS AX 0.0911 IX 1e-006 IY 0.005 IZ 0.054
84 97 120 133 156 169 192 205 PRIS AX 0.0992 IX 1e-006 IY 0.009 IZ 0.057
85 86 95 96 121 122 131 132 157 158 167 168 193 194 203 -
204 PRIS AX 0.1073 IX 1e-006 IY 0.015 IZ 0.059
87 88 93 94 123 124 129 130 159 160 165 166 195 196 201 -
202 PRIS AX 0.1108 IX 1e-006 IY 0.018 IZ 0.06
89 TO 92 125 TO 128 161 TO 164 197 TO 199 -
200 PRIS AX 0.1143 IX 1e-006 IY 0.022 IZ 0.061
301 307 553 559 PRIS AX 0.041 IX 1e-006 IY 0.0083 IZ 0.0001
302 TO 306 372 TO 376 484 TO 488 554 TO 557 -
558 PRIS AX 0.044 IX 1e-006 IY 0.00053 IZ 0.0161
308 TO 328 357 TO 371 377 TO 391 420 TO 440 469 TO 483 489 TO 503 532 TO 551 -
552 PRIS AX 0.067 IX 1e-006 IY 0.0347 IZ 0.0002
329 TO 356 392 TO 419 441 TO 468 504 TO 530 -
531 PRIS AX 0.026 IX 1e-006 IY 9e-005 IZ 0.0079
665 673 681 689 TAPERED 1.5 0.4 1.743 0.8 0.4 0.8 0.4
666 674 682 690 TAPERED 1.743 0.4 2.052 0.8 0.4 0.8 0.4
667 675 683 691 699 703 707 711 TAPERED 2.052 0.4 2.185 0.8 0.4 0.8 0.4
668 676 684 692 700 704 708 712 TAPERED 2.185 0.4 2.318 0.8 0.4 0.8 0.4
669 677 685 693 701 705 709 713 TAPERED 2.318 0.4 2.385 0.8 0.4 0.8 0.4
670 678 686 694 702 706 710 714 TAPERED 2.385 0.4 2.415 0.8 0.4 0.8 0.4
671 679 687 695 TAPERED 2.415 0.4 2.5084 0.8 0.4 0.8 0.4
672 680 688 696 TAPERED 2.5084 0.4 3 0.8 0.4 0.8 0.4
697 698 PRIS YD 1 ZD 0.6
ISOTROPIC MATERIAL1
E 2.11e+007
POISSON 0.3
DENSITY 7.85
ALPHA 1.2e-005
ISOTROPIC CONCRETE
E 3.2e+006
POISSON 0.17
DENSITY 2.5
ALPHA 1e-005
DAMP 0.05
END DEFINE MATERIAL
CONSTANTS
SUPPORTS
122 159 PINNED
349 354 359 364 FIXED
MEMBER RELEASE
LONG
LOAD 1 SEISMIC TRANS
SELFWEIGHT X 0.18
*LOAD 3 SEISMIC LONG
PERFORM ANALYSIS
Page 152 of 156
216 TO 234
441 TO 468 483 TO 489 504 TO 531 553 TO 559
FINISH
Page 153 of 156

WIND LOAD
51 52 57 58 231 232 237 238 PRIS AX 0.0902 IX 1e-006 IY 0.008 IZ 0.053

73 TO 77 104 TO 113 140 TO 149 176 TO 185 212 TO 215 -
216 PRIS AX 0.11 IX 1e-006 IY 0.018 IZ 0.06
78 103 114 139 150 175 186 211 PRIS AX 0.105 IX 1e-006 IY 0.013 IZ 0.059
79 80 101 102 115 116 137 138 151 152 173 174 187 188 209 -
210 PRIS AX 0.1 IX 1e-006 IY 0.01 IZ 0.057
81 100 117 136 153 172 189 208 PRIS AX 0.0919 IX 1e-006 IY 0.006 IZ 0.054
82 83 98 99 118 119 134 135 154 155 170 171 190 191 206 -
207 PRIS AX 0.0911 IX 1e-006 IY 0.005 IZ 0.054
84 97 120 133 156 169 192 205 PRIS AX 0.0992 IX 1e-006 IY 0.009 IZ 0.057
85 86 95 96 121 122 131 132 157 158 167 168 193 194 203 -
204 PRIS AX 0.1073 IX 1e-006 IY 0.015 IZ 0.059
87 88 93 94 123 124 129 130 159 160 165 166 195 196 201 -
202 PRIS AX 0.1108 IX 1e-006 IY 0.018 IZ 0.06
89 TO 92 125 TO 128 161 TO 164 197 TO 199 -
200 PRIS AX 0.1143 IX 1e-006 IY 0.022 IZ 0.061
301 307 553 559 PRIS AX 0.041 IX 1e-006 IY 0.0083 IZ 0.0001
302 TO 306 372 TO 376 484 TO 488 554 TO 557 -
558 PRIS AX 0.044 IX 1e-006 IY 0.00053 IZ 0.0161
308 TO 328 357 TO 371 377 TO 391 420 TO 440 469 TO 483 489 TO 503 532 TO 551 -
552 PRIS AX 0.067 IX 1e-006 IY 0.0347 IZ 0.0002
329 TO 356 392 TO 419 441 TO 468 504 TO 530 -
531 PRIS AX 0.026 IX 1e-006 IY 9e-005 IZ 0.0079
665 673 681 689 TAPERED 1.5 0.4 1.743 0.8 0.4 0.8 0.4
666 674 682 690 TAPERED 1.743 0.4 2.052 0.8 0.4 0.8 0.4
667 675 683 691 699 703 707 711 TAPERED 2.052 0.4 2.185 0.8 0.4 0.8 0.4
668 676 684 692 700 704 708 712 TAPERED 2.185 0.4 2.318 0.8 0.4 0.8 0.4
669 677 685 693 701 705 709 713 TAPERED 2.318 0.4 2.385 0.8 0.4 0.8 0.4
670 678 686 694 702 706 710 714 TAPERED 2.385 0.4 2.415 0.8 0.4 0.8 0.4
671 679 687 695 TAPERED 2.415 0.4 2.5084 0.8 0.4 0.8 0.4
672 680 688 696 TAPERED 2.5084 0.4 3 0.8 0.4 0.8 0.4
697 698 PRIS YD 1 ZD 0.6
ISOTROPIC MATERIAL1
E 2.11e+007
POISSON 0.3
DENSITY 7.85
ALPHA 1.2e-005
ISOTROPIC CONCRETE
E 2.21467e+006
POISSON 0.17
DENSITY 2.40262
ALPHA 1e-005
DAMP 0.05
END DEFINE MATERIAL
CONSTANTS
SUPPORTS
122 159 PINNED
349 354 359 364 FIXED
MEMBER RELEASE
LOAD 1 WIND TRANS
MEMBER LOAD
1 TO 36 UNI Z -1.45
LOAD 2 WIND ON PYLON
Page 154 of 156
MEMBER LOAD
665 673 TRAP Z -0.735 -0.857
666 674 TRAP GZ -0.857 -1.013
667 675 TRAP GZ -1.013 -1.08
668 676 TRAP Z -1.08 -1.147
669 677 TRAP Z -1.147 -1.18
670 678 TRAP Z -1.18 -1.213
671 679 TRAP Z -1.213 -1.28
672 680 TRAP Z -1.28 -1.538
LOAD 3 WIND UP/DOWN
MEMBER LOAD
37 TO 252 UNI Y -0.233
PERFORM ANALYSIS
*PRINT SUPPORT REACTION
PRINT JOINT DISPLACEMENTS
FINISH
Page 155 of 156

1. STAAD PLANE PIER P144
INPUT FILE: PIER p144 DEFLECTION.STD
2. START JOB INFORMATION
3. ENGINEER DATE 30-NOV-13
4. END JOB INFORMATION
5. INPUT WIDTH 79
6. PAGE LENGTH 15000
7. UNIT METER MTON
8. JOINT COORDINATES
9. 1 0 0 0
10. 2 0 23 0
11. MEMBER INCIDENCES
12. 1 1 2
13. MEMBER PROPERTY CANADIAN
14. * A=0.7*PI*3.2^2/4, I= 0.7* PI*3.2^4/64
15. 1 PRIS AX 5.63 IZ 3.603
16. DEFINE MATERIAL START
17. ISOTROPIC MATERIAL1
18. E 3.5E6
19. POISSON 0.3
20. DENSITY 7.85
21. END DEFINE MATERIAL
22. CONSTANTS
23. MATERIAL MATERIAL1 ALL
24. SUPPORTS
25. 1 FIXED
26. LOAD 1 HOR LOAD NORMAL CASE
27. JOINT LOAD
28. 2 FX 44.1
29. PERFORM ANALYSIS
30. PRINT MEMBER FORCES
31. PRINT JOINT DISPLACEMENTS
JOINT DISPLACEMENT (CM RADIANS) STRUCTURE TYPE = PLANE

------------------
JOINT LOAD X-TRANS Y-TRANS Z-TRANS X-ROTAN Y-ROTAN Z-ROTAN
1 1 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000

2 1 1.4183 0.0000 0.0000 0.0000 0.0000 -0.0009
************** END OF LATEST ANALYSIS RESULT **************
32. FINISH
Page 156 of 156

SCC 25 - 40 - 35M Span DN - 102a

Uploaded by

Copyright:

Available Formats

SCC 25 - 40 - 35M Span DN - 102a

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SCC 25 - 40 - 35M Span DN - 102a

Uploaded by

Copyright:

Available Formats

CLIENT:

BIHAR STATE ROAD DEVELOPMENT

CONSTRUCTION OF ELEVATED ROAD

GAMMON INDIA LIMITED

Date Rev No. Revision By

DESIGN OF SCC SUPERSTRUCTURE (25+40+25 M SPAN)

4 TABULATION OF BENDING MOMENT AND SHEAR FORCE

5 CALCULATION OF STRESSES DUE TO TEMP GRADIENT

6 CALCULATION OF STRESSES DUE TO DIFF SHRINKAGE

7 FLEXURE AND SHEAR CHECK

8 DESIGN OF SHEAR CONNECTORS

9 DESIGN OF CROSS GIRDERS

10 DESIGN OF SPLICES AND WEB STIFFNERS

11 DEFLECTION CHECK AND PRECAMBER CALCS

12 FORCES AND MOVEMNTS ON BEARINGS

13 DESIGN OF BEARING STIFFENERS

15 DESIGN OF DECK SLAB

Apdx A STADD INPUT FILES

ψ 0.88 0.79 0.71 0.57 0.44

S No. No. A z Az Az2 I0 I0+Az2

Section Properties with holes without holes

Section Properties at other location (No Holes deducted)

S No. No. A z Az Az2 I0 I0+Az2

Section Properties with holes without holes

Section Properties at other location (No Holes deducted)

S No. No. A z Az Az2 I0 I0+Az2

Section Properties with holes without holes

Section Properties at other location (No Holes deducted)

S No. No. A z Az Az2 I0 I0+Az2

Section Properties with holes without holes

Section Properties at other location (No Holes deducted)

S No. No. A z Az Az2 I0 I0+Az2

Section Properties with holes without holes

Section Properties at other location (No Holes deducted)

S No. No. A z Az Az2 I0 I0+Az2

Section Properties with holes without holes

Calculation of Ixx ψ = 1.000 ω = 0.500

S No. No. A z Az Az2 I0 I0+Az2

Section Properties with holes without holes

Section Properties at other location (No Holes deducted)

S No. No. A z Az Az2 I0 I0+Az2

Section Properties with holes without holes

Calculation of Ixx ψ = 1.000 ω = 0.500

S No. No. A z Az Az2 I0 I0+Az2

Section Properties with holes without holes

S No. No. A z Az Az2 I0 I0+Az2

Section Properties with holes without holes

Section Properties at other location (No Holes deducted)

S No. No. A z Az Az2 I0 I0+Az2

Section Properties with holes without holes

Section Properties at other location (No Holes deducted)

S No. No. A z Az Az2 I0 I0+Az2

Section Properties with holes without holes

Section Properties at other location (No Holes deducted)

S No. No. A z Az Az2 I0 I0+Az2

Section Properties with holes without holes

Section Properties at other location (No Holes deducted)

S No. No. A z Az Az2 I0 I0+Az2

Section Properties with holes without holes

stress εdif x Es= 0.00022000000000.43 1.7E+04 kN/sqm

stress εdif x Es= 0.00022000000000.43 1.7E+04 kN/sqm