Celstran® PP-GF50-0403 P10/10

Celanese Corporation - Polypropylene Thursday, May 30, 2024

General Information
Product Description
50% long glass fiber reinforced PP
Material code according to ISO 1043-1: PP Heat stabilized polypropylene reinforced with 50 weight percent long glass fibers. Black. The fibers are
chemically coupled to the polypropylene matrix. The pellets are cylindrical and normally as well as the embedded fibers 11 mm long. Parts molded of
CELSTRAN have outstanding mechanical properties such as high strength and stiffness combined with high heat deflection. The notched impact
strength is increased at elevated and low temperatures due to the fiber skeleton built in the parts. The long fiber reinforcement reduces creep
significantly. The very isotropic shrinkage in the molded parts minimizes the warpage. Complex parts can be manufactured with high reproducibility
by injection molding. Application field: Functional/structural parts for automotive
General
Material Status • Commercial: Active
• Africa & Middle East • Europe
Availability • North America
• Asia Pacific • Latin America
Filler / Reinforcement • Glass Fiber
Uses • Automotive Applications
Automotive Specifications • DAIMLER DBL 5416 1 • LI AUTO INC Q/LIA 5310050 2
Forms • Pellets
Processing Method • Injection Molding

ASTM & ISO Properties 3

Physical Nominal Value Unit Test Method
Density 1.34 g/cm³ ISO 1183
Mechanical Nominal Value Unit Test Method
Tensile Modulus 11600 MPa ISO 527-1
Tensile Stress (Break) 140 MPa ISO 527-2/5
Tensile Strain (Break) 1.8 % ISO 527-2/5
Flexural Modulus ISO 178
-- 12000 MPa
80°C 8500 MPa
Flexural Stress ISO 178
-- 220 MPa
80°C 125 MPa
Impact Nominal Value Unit Test Method
Charpy Notched Impact Strength ISO 179/1eA
-30°C 33 kJ/m²
23°C 32 kJ/m²
Charpy Unnotched Impact Strength ISO 179/1eU
-30°C 58 kJ/m²
23°C 60 kJ/m²
Thermal Nominal Value Unit Test Method
Deflection Temperature Under Load ISO 75-2/A
1.8 MPa, Unannealed 158 °C
Deflection Temperature Under Load ISO 75-2/C
8.0 MPa, Unannealed 134 °C
Melting Temperature 4 165 °C ISO 11357-3

UL LLC ©2024. All rights reserved.

The information presented here was acquired by UL from the producer of the product or material or original information provider. However, UL assumes no
responsibility or liability for the accuracy of the information contained on this website and strongly encourages that upon final product or material selection
information is validated with the manufacturer. This website provides links to other websites owned by third parties. The content of such third party sites is not within
www.ulprospector.com our control, and we cannot and will not take responsibility for the information or content.
Page: 1 of 2
Celstran® PP-GF50-0403 P10/10
Celanese Corporation - Polypropylene
Thermal Nominal Value Unit Test Method
CLTE - Flow 1.5E-5 cm/cm/°C ISO 11359-2
CLTE - Transverse 7.7E-5 cm/cm/°C ISO 11359-2
Electrical Nominal Value Unit Test Method
5 550 V IEC 60112
Comparative Tracking Index
Flammability Nominal Value Unit Test Method
Flame Rating (2.0 mm) HB UL 94

Processing Information
Injection Nominal Value Unit
Drying Temperature 90 to 100 °C
Drying Time 2.0 hr
Suggested Max Moisture 0.20 %
Injection Feed Temperature 20 to 50 °C
Rear Temperature 220 to 240 °C
Middle Temperature 220 to 240 °C
Front Temperature 230 to 250 °C
Injection Zone 4 Temperature 230 to 250 °C
Nozzle Temperature 230 to 250 °C
Processing (Melt) Temp 230 to 250 °C
Mold Temperature 30 to 70 °C
Injection Rate Slow
Back Pressure < 3.00 MPa
Hot Runner 240 to 270 °C
Screw Speed
4.00 cm 50
5.50 cm 35
7.50 cm 25

Notes
1
MBN 10506 (Kalahari)
2
2021 (V2)
3
Typical properties: these are not to be construed as specifications.
4
10°C/min
5
100 drops

UL LLC ©2024. All rights reserved.

The information presented here was acquired by UL from the producer of the product or material or original information provider. However, UL assumes no
responsibility or liability for the accuracy of the information contained on this website and strongly encourages that upon final product or material selection
information is validated with the manufacturer. This website provides links to other websites owned by third parties. The content of such third party sites is not within
www.ulprospector.com our control, and we cannot and will not take responsibility for the information or content.
Page: 2 of 2