HelixNet Partyline User Guide 399G159A

Download as pdf or txt
Download as pdf or txt
You are on page 1of 293

Digital Partyline User Guide

PN: 399G159 Rev: A 24 November 2015


Document Reference

Clear-Com HelixNet Partyline User Guide


Part Number: 399G159 Revision: A
Legal Disclaimers

Copyright © 2015 HME Clear-Com Ltd.


All rights reserved.
Clear-Com, the Clear-Com logo, Clear-Com Concert and HelixNet are registered
trademarks of HM Electronics, Inc.
The software described in this document is furnished under a license agreement
and may be used only in accordance with the terms of the agreement.
The product described in this document is distributed under licenses restricting its
use, copying, distribution, and decompilation/reverse engineering. No part of this
document may be reproduced in any form by any means without prior written
authorization of Clear-Com, an HME Company.
This product is covered by U.S. Patent Nos. 8,311,085 and 8,553,865 and by
European Patent No. 2 176 987 B1.
Clear-Com Offices are located in California, USA; Cambridge, UK; Montreal,
Canada; and Beijing, China. Specific addresses and contact information can be
found on Clear-Com’s corporate website:
www.clearcom.com
Clear-Com Contacts

Americas and Asia-Pacific Headquarters


California, United States
Tel: +1.510.337.6600
Email: [email protected]

Europe, Middle East, and Africa Headquarters


Cambridge, United Kingdom
Tel: +44 1223 815000
Email: [email protected]

China Office
Beijing Representative Office
Beijing, P.R.China
Tel: +8610 65811360 / 65815577

Page 2
Contents
Contents 3

1 Introduction .......................................................................... 8
1.1 Important Safety instructions .................................................... 8
1.2 Methods of connection: system overview .................................. 10
1.3 Further information ................................................................ 14

2 Panels and Interfaces .......................................................... 15


2.1 Main Station/Remote Station: Front panel ................................. 15
2.2 HMS-4X Main Station: rear panel ............................................. 22
2.3 Remote Station rear panel ...................................................... 28
2.4 Speaker Station .................................................................... 31
2.5 HBP-2X Beltpack ................................................................... 39

3 Installing HelixNet Partyline ............................................... 44


3.1 Planning your HelixNet Partyline installation .............................. 45
3.2 Installing the Main Station/Remote Station ................................ 50
3.3 Installing the Speaker Station ................................................. 51
3.4 Installing the HBP-2X Beltpacks ............................................... 54
3.5 HelixNet infrastructure ........................................................... 54
3.6 Converting analogue partylines to HelixNet ............................... 56

4 IP Network Structure .......................................................... 57


4.1 Network connections .............................................................. 57
4.2 Multiple Groups in the same IP Network .................................... 58
4.3 Link Local Environments ......................................................... 58

5 Configuring and managing the Main Station from device


menus ................................................................................. 61
5.1 Using the Menus .................................................................... 61
5.2 Configuring the Audio settings ................................................. 63
5.3 Selecting Station Settings ....................................................... 69
5.4 Configuring the channel settings .............................................. 74
Page 3
5.5 Configuring the Control I/O ..................................................... 76
5.6 Configuring Module Settings .................................................... 78
5.7 Administration ...................................................................... 88
5.8 Diagnostics ........................................................................... 91
5.9 Setting up a key Expansion Group ........................................... 93

6 Configuring and managing the Remote Station from


device menus ...................................................................... 97
6.1 Configuring the audio settings ................................................. 97
6.2 Selecting Station Settings ......................................................101
6.3 Configuring the channel settings .............................................101
6.4 Configuring the Control I/O ....................................................103
6.5 Connecting the Remote Station to a Main Station using LAN .......104
6.6 Administration .....................................................................105
6.7 Diagnostics ..........................................................................107
6.8 Setting up a key Expansion Group ..........................................108

7 Using the Main Station/Remote Station ............................ 109


7.1 Using the gooseneck mic, loudspeaker and headset ...................109
7.2 Entering and exiting Menu mode .............................................111
7.3 A HelixNet Link-Group Overview .............................................112
7.4 Device configuration in the CCM .............................................113
7.5 Linking Main Stations in the CCM ............................................114
7.6 Using the channel keysets .....................................................116
7.7 Using the All Talk key ............................................................117
7.8 Using the SA [Stage Announce] key ........................................117
7.9 Using the RMK [Remote Mic Kill] key .......................................118
7.10 Line 1 and 2 LEDs .................................................................119
7.11 Line and LAN LEDs ................................................................120

8 Configuring and managing the Speaker Station from


device menus .................................................................... 121
8.1 Using the Menus ...................................................................121
8.2 Configuring the Audio settings ................................................122
8.3 Station Settings ...................................................................122
Page 4
8.4 Connecting the Speaker Station to a Main Station .....................123
8.5 Module Settings ...................................................................123
8.6 Administration .....................................................................123
8.7 Diagnostics ..........................................................................124

9 Using the Speaker Station ................................................. 125


9.1 Using the gooseneck mic, loudspeaker and headset ...................125
9.2 Entering and exiting Menu mode .............................................127
9.3 Using the channel keysets .....................................................127
9.4 Line and LAN LEDs ................................................................128

10 Configuring and managing the HBP-2X Beltpack from


device menus .................................................................... 129
10.1 Using the Menus ...................................................................129
10.2 Configuring the Role settings..................................................130
10.3 Configuring the Audio settings ................................................130
10.4 Audio settings for the microphone ...........................................132
10.5 Configuring the Beltpack Settings ...........................................132
10.6 Configuring the Display Settings .............................................134
10.7 Administration .....................................................................136
10.8 Diagnostics ..........................................................................137

11 Using the HBP-2X Beltpack ................................................ 138


11.1 Using the beltpack keysets.....................................................138
11.2 Entering and exiting Menu mode .............................................139
11.3 Adjusting the Program Feed volume level. ................................139

12 Roles ................................................................................. 140


12.1 Roles overview .....................................................................140
12.2 Example Roles set up ............................................................141
12.3 Device default Roles .............................................................145
12.4 To select a Role for a device ...................................................145
12.5 Creating and editing Roles in the CCM .....................................145

13 Core Configuration Manager (CCM) ................................... 149


13.1 Access the CCM ....................................................................150
Page 5
13.2 Minimum requirements for the CCM ........................................150
13.3 Overview page .....................................................................151
13.4 Home page ..........................................................................152
13.5 General Page .......................................................................153
13.6 Save/Restore System Settings ...............................................154
13.7 Linking page ........................................................................155
13.8 Roles Page ..........................................................................156
13.9 Assignments page ................................................................158

14 Using the CCM to configure Roles ...................................... 162


14.1 Editing Main Station roles ......................................................162
14.2 General Purpose Input (GPI) and General Purpose Output
(GPO) triggers. ....................................................................167
14.3 Editing Remote Station roles ..................................................171
14.4 Editing Speaker Station roles .................................................172
14.5 Editing the Beltpack roles ......................................................173
14.6 Disable menu access on any device from the CCM .....................176
14.7 Configure a stacked key on a beltpack using the CCM ................176
14.8 Call a beltpack using the USB flasher feature ............................177

15 Linking in the Core Configuration Manager (CCM) ............. 179


15.1 A HelixNet Link-Group Overview .............................................179
15.2 Device configuration in the CCM .............................................180
15.3 Linking Main Stations in the CCM ............................................181

16 Linking Main Stations (cabling and linking from device


menus) .............................................................................. 184
16.1 Linking scenarios ..................................................................184

17 Linking Remote Stations and Speaker Stations.................. 188


17.1 Linking scenarios ..................................................................189
17.2 Networking Specifications ......................................................194

18 Connecting to Other Intercom Systems ............................. 195


18.1 Connecting HelixNet Partyline to Encore® .................................195
18.2 Connecting HelixNet Partyline to RTS (Telex) two-wire systems ..198

Page 6
18.3 Connecting HelixNet Partyline to Tempest® ..............................201
18.4 Connecting HelixNet Partyline to CellCom® / FreeSpeak®............207
18.5 Connecting HelixNet Partyline to the DX210 .............................212
18.6 Connecting HelixNet Partyline to Eclipse® .................................217
18.7 Connecting HelixNet Partyline to two-way radio systems ............223

19 Specifications .................................................................... 230


19.1 Main Station (HMS-4X) ..........................................................230
19.2 Two-wire module (HLI-2W2) ..................................................236
19.3 Four-wire module (HLI-4W2)..................................................237
19.4 Remote Station (HRM-4X)......................................................237
19.5 Speaker Station (HKB-4X) .....................................................243
19.6 Beltpack (HBP-2X) ................................................................246

20 Glossary ............................................................................ 248

21 Menu maps ........................................................................ 251

22 Menu trees ........................................................................ 274

23 Cabling reference .............................................................. 279


23.1 Interoperability ....................................................................279
23.2 Cable capacitance versus distance ..........................................280
23.3 Cable connections .................................................................284

24 Troubleshooting ................................................................ 289

25 Compliance ........................................................................ 292

Page 7
1 Introduction
This guide is intended to help you install, configure, and use the HelixNet
Partyline™ system.
HelixNet Partyline is a digital intercom system, featuring the award-winning I.V.
Core Technology from Clear-Com®. The system is designed to be as simple to use
and configure as a two-wire intercom / analog Partyline system, while exploiting
the flexibility and network management capabilities of a matrix system.
To expedite integration with your existing intercom infrastructure, HelixNet
Partyline also features:
 Highly configurable Control I/O and Module settings.
 Intuitive and easy to use online Core Configuration Manager to configure
and control HelixNet units.
 Flexible cabling options (microphone cable, CAT5).
Note: Cabling for a HelixNet system should always be screened.
 Optional 2-Wire and 4-Wire interface modules.
 Optional Main Station linking (LAN or Fiber or combination).
 Expansion option to enable talk and listen on more than four channels.
 Beltpacks and wall/desktop Remote Stations that connect to a system
that contains a Main Station.

1.1 Important Safety instructions


HelixNet digital partyline uses cable infrastructure to transport audio and data
over a range of frequencies. The maximum frequency used for transmission is
approximately 25MHz. Depending on the amount of audio and data transmitted,
HelixNet digital partyline can work with as much as 90dB signal attenuation.
However, the receivers are very sensitive and are susceptible to crosstalk
between cables.
Therefore it is important to maintain cable shield integrity through all
connectors, splitter boxes and patch panels.
 Read these instructions.
 Keep these instructions.
 Heed all warnings.
 Follow all instructions.
 Do not use this apparatus near water.
 Clean only with dry cloth.

Page 8
 Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
 Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
 Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades and a third grounding prong. The
wide blade or the third prong is provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement
of the obsolete outlet.
 Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
 Only use attachments/accessories specified by the manufacturer.
 Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury
from tip-over.
 Unplug this apparatus during lightning storms or when unused for long
periods of time.
 Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-cord
supply or plug is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
Warning: To reduce the risk of fire or electric shock, do not expose this product
to rain or moisture.

Safety symbols
Familiarize yourself with the safety symbols in Figure 1: Safety symbols. These
symbols are displayed on the apparatus and warn you of the potential danger of
electric shock if the system is used improperly.

Page 9
Figure 1-1: Safety symbols
Note: Important. For compliance notices, see 20 Compliance.

1.2 Methods of connection: system overview


HelixNet devices can be connected in several different ways. A combination of
these methods can be used.

Connecting by cable (powerline).

Figure 1-2 Connecting devices by cable


In this scenario devices are connected by cable in either a daisy chain or home
run fashion. Power and data are passed down this connection in what is known as
a powerline.
See 17 Linking Remote Stations and Speaker Stations for detail on different types
of device layout (topologies).
Page 10
Up to 20 beltpacks can be connected to one Main Station, and Remote and
Speaker Stations can be included in the powerline.
However, including Remote and Speaker Stations in the powerline will affect the
amount of devices that can be connected, as Main and Remote Stations draw
more power than beltpacks.
You can find the URL to a powerline/distance calculator at the beginning of
Chapter 3. Installing HelixNet Partyline.

Pairing by LAN

Figure 1-3 Pairing by LAN (or Fiber)


When pairing by LAN, devices are connected to the same network by Ethernet
cable (RJ45) and then paired from the device menus.
See 17.1.2 Ethernet point-to-point link for more detail.
Note: Pairing by LAN offers better latency than connecting with cable.

Page 11
Connecting more than one Main Station (Linking)

Figure 1-4 Linking Main Stations by Ethernet


Up to three Main Stations can be linked. In earlier versions of HelixNet (2.0 and
below) linking Main Stations was a way of expanding the Channel capacity of your
system (4 Channels on each Main Station). In HelixNet 3.0 this is no longer
necessary as each Main Station already has 12 Channels, with the option of
licensing another 12 (24 Channels in total). A system, regardless of the number of
linked HMS units, will have 12 channels by default with the potential of increasing
that number to 24 with the purchase of a license for each HMS within the Link-
Group.
Linking Main Stations in HelixNet 3.0 has the following benefits:
 More beltpack connections (20 per Main Station)
 System distribution as far as your LAN allows.
 The ability to configure all devices from an Internet browser using the CCM
(Core Configuration Manager).

Page 12
Figure 1-5 Linking Main Stations in the Core Configuration Manager (CCM)
Main Stations can be linked using different methods:
 By Ethernet and RJ-45 cable in your LAN. See 16 Linking Main Stations
(cabling and linking from device menus).
 By IP address/hostname using the CCM. See 15 Linking in the Core
Configuration Manager (CCM)

Key Expansion Groups (Main Stations and Remote


Stations)

Figure 1-6 Key Expansion Group


Devices can be set up as a key Expansion Group to allow convenient control of
audio from one device, and to increase the “key” capacity so that a user can view
and control more than 4 keys (up to 24 with 5 expansion panels).
Page 13
See 5.9 Setting up a key Expansion Group for detail.

1.3 Further information


For the latest information about HelixNet Partyline, including software updates,
see:
http://www.clearcom.com/product/helixnet.
For information about Clear-Com accessories, including headsets and
gooseneck microphones, see http://www.clearcom.com/product/accessories.
For legal and contact information, see Page 2 of this guide.

Page 14
2 Panels and Interfaces

2.1 Main Station/Remote Station: Front panel

Figure 2-1: Main Station/Remote Station: Front panel

Page 15
Key to Main Station/Remote Station: Front panel
Feature Description

A Ear for rack mounting Main Station/Remote Station.

B Headset socket (4-pin XLR–M)

Pin Function
1 Mic ground
2 Mic +
3 Earphone ground
4 Earphone
Table 2-1: Headset socket pin out

C Gooseneck microphone socket (3-pin female Tuchel connector)

D Mic control [MIC ON]. Press to activate mic audio.

E Headset key [HSET]. Press to activate the headset mic. When the
headset is connected, the gooseneck microphone is disconnected.
Audio output to the loudspeaker is diverted to the headphones.

F Menu. Press to display the Main Station menus in the display screens
G
[ ]. Use the rotary control for each display screen to scroll and
select menu items. See 2.1.1 Main Station/Remote channel keyset.

G Channel keyset. There is a keyset (set of controls) addressable to


any of the available channels. See 2.1.1 Main Station/Remote channel
keyset.

H Stage Announce [SA]. Press to talk to connected Public Address


(PA) / Stage Announce (SA) system (see 2.2 HMS-4X Main Station:
rear panel).
SA mutes any active Talk key on any of the 4 keysets, and transmits
audio from either headset or gooseneck microphone to the SA Output
port on the rear of the unit. If the SA is assigned to a Channel, then
any talker within the channel has their audio routed to the associated
SA Port.
When the SA is pressed, Mic select [MIC ON] is also lit bright red,
indicating that mic audio is active. See 7.8 Using the SA [Stage
Announce] key.

Page 16
Key to Main Station/Remote Station: Front panel
Feature Description

I Master Station
LEDs for lines 1 and 2 (digital partylines). The LEDs indicate
the status of the intercom circuit powering. When an LED is lit:
 Green, the line is functioning.
 Amber, the line is busy.
 Red, there is an error or fault on the line.
Remote Station
LEDs for line status and LAN status. The LEDs indicate the status
of the intercom circuit powering. When an LED is lit:
Green, the line is functioning.
Amber, the line is busy.
Red, there is an error or fault on the line.
If there is a fault on a powerline output, the Line STATUS indicator
will turn off and the red FAULT indicator will flash. Possible causes of
a fault include overvoltage, overcurrent, short circuit to ground or
severe brown-outs.

J Loudspeaker. When a headset is connected [ B ] and selected [


E
], loudspeaker output is diverted to the headphones.

K Program feed audio level rotary control [Program].


 To increase the volume of the program feed to the loudspeaker
/ headphones, turn clockwise (up to 360°).
 To decrease the volume, turn anticlockwise (up to 360°). As
you increase or decrease the volume, the level control LEDs
pass through a range of indicator colors:
LED color Volume level
Green Low
Amber / Green Low / Medium
Amber Medium
Red / Amber Medium / High
Red High
Table 2-2 : Volume Indicator colors

L Loudspeaker / Headphone audio level rotary control [Main].


To increase the volume to the loudspeaker / headphones, turn
clockwise (up to 360°). To decrease the volume, turn anticlockwise
(up to 360°). Push to mute or unmute.
As you increase or decrease the volume, the level control LEDs pass
through a range of indicator colors. For more information, see Table
2-2 : Volume Indicator colors
Page 17
Key to Main Station/Remote Station: Front panel
Feature Description

M Main Station:
Remote Mic Kill [RMK]. Press to:
 Unlatch all latched talk keys for either all displayed Channels or
all Channels within the system (configurable within the Role)
Remote Station:
Option [OPT] – Can be configured as an RMK button (see section
7.9 Using the RMK [Remote Mic Kill] key).

N All Talk. Press to talk to all channels (intercom devices and systems)
connected to the Main Station.

O USB 2.0 (Micro-AB) connector. For software upgrades (see 5.7.2


Updating the software and 5.7.6 Saving and restoring the
software settings.).
Note: This connector is not present on the Remote Station.

P USB 2.0 (Standard-A) connector. For software upgrades (see 5.7.2


Updating the software and 5.7.6 Saving and restoring the
software settings.).
Table 2-3 Key to Main Station/Remote Station front panel diagram
Note: The Main Station/Remote Station does not have a power switch, button
or key. The system powers up when you connect the power supply.
Power up time depends on the amount of equipment connected.

Page 18
Main Station/Remote channel keyset and display

Figure 2-2: Main Station/Remote Station (Front panel): Keyset

Key to Main Station/Remote Station front panel: Channel keyset


Feature Description

A Display screen.
There are multiple screensaver options. If the Rotary controls are
touched, this screen also displays the sound level on the Channel
(controlled by the rotary) and the system information icons. For an
explanation of system information icons see Table 2-5 Main
Station/Remote Station display icons and indicators.
In Menu mode, the display screens display the four levels of menu.
The menu hierarchy proceeds left to right:
 The top level menu is presented in the first screen (furthest left
on the front panel).
 The lowest level menu is presented in the fourth screen
(furthest right on the front panel).
If the display is in Menu mode, the display screen times out of Menu
mode and displays the channel label if no key is pressed for 20
seconds.
For more information about Menu mode, see 5.1 Using the Menus.

B Rotary control. Turn to increase or decrease the listen volume level


for the channel, or to scroll menu items when in menu mode. To
select menu items, press the control.

C Talk key. Press to talk on the channel and to all nodes (intercom
devices and systems) listening into the channel.

D Call key. Press to send a call signal to all nodes (intercom devices
and systems) listening into the channel.
Table 2-4: Key to Main Station/Remote Station front panel: Key Set

Page 19
Note: If the Main Station/Remote Station remains inactive for 10 minutes, the display
screens enter screensaver mode (see 5.3.9 Setting the screensaver).
Main Station/Remote Station display icons and indicators
Name Icon Description
Channel A descriptive name for the channel. The maximum
label length is 10 characters.
Channel The volume of the channel audio.
listen
volume level
Link with Appears on the Main Station when linking is
another enabled.
HMS
Not linked Appears on the Main Station when a connection to
another Main Station is lost.
Paired Appears on the Remote Station and Speaker
Station when it is connected properly over LAN.
Not paired Flashes on the Remote Station and Speaker
Station when the connection is not configured
properly.
Signal Appears on the Remote Station, Speaker Station
strength and beltpack. One to five bars indicate the
strength of the signal from the Main Station.
Locked Locked Appears on the beltpack when you try to access
the menu while the menu has been locked at the
Main Station.
Mute Appears on the Main Station, Remote Station and
Speaker Station when the rotary control for any
channel on the Main/Remote Station is pressed.
Opto (GPI) Appears on the Main Station and Remote Station
close to the Call or Talk button if it is associated
with an Opto.
Relay (GPO) Appears on the Main Station and Remote Station
close to the Call or Talk button if it is associated
with a Relay.
Program PGM Appears on the Main Station, Remote Station,
Speaker Station and beltpack when a program
input is assigned to a channel.
IFB IFB Appears on the Main Station, Remote Station,
Speaker Station and beltpack when a program
input is assigned to a channel and IFB is enabled.
2W/4W 2W/4W Appears on the Main Station, Remote Station and
Speaker Station when a 2W/4W input is assigned
Page 20
Main Station/Remote Station display icons and indicators
Name Icon Description
to a channel.
Limiter LIM Appears on the Main Station, Remote Station,
Speaker Station and beltpack when the headset
limiter is enabled.
Expansion Appears on the Main Station and Remote Station
when the device is part of an Expansion Group.
Warning Appears on the Main Station, Remote Station,
Speaker Station and beltpack when something is
wrong. Warning messages can be accessed in the
Diagnostic menu.
Table 2-5 Main Station/Remote Station display icons and indicators

Page 21
2.2 HMS-4X Main Station: rear panel

Figure 2-3: HMS-4X Main Station: rear panel (including optional modules HLI-2W2 and HLI-4W2)

Page 22
Key to Main Station: rear panel
Feature Description

A Power supply with metal cable clip. The power supply operates at
100 - 240 VAC / 50-60Hz / 250 watts / T 3.15A H 250 V.

B Control I/O (25 way female D-type). Use to connect up to 4 relay


control outputs and 4 optically isolated control inputs (see 5.5
Configuring the Control I/O).

Pin Function Pin Function


Pin 1 Relay 1 NC Pin 14 Relay1 Pole
Pin 2 Relay 1-NO Pin 15 Relay 2 NC
Pin 3 Relay2-Pole Pin 16 Relay 2-NO
Pin 4 Relay 3 NC Pin 17 Relay3 Pole
Pin 5 Relay 3-NO Pin 18 Relay 4 NC
Pin 6 Relay4-Pole Pin 19 Relay 4-NO
Pin 7 Pin 20 +5V
Pin 8 GND Pin 21 +5V
Pin 9 GND Pin 22 Opto 1-
Pin 10 Opto 1+ Pin 23 Opto 2-
Pin 11 Opto 2+ Pin 24 Opto 3-
Pin 12 Opto 3+ Pin 25 Opto 4-
Pin 13 Opto 4+
Table 2-6: Control I/O pin out

C Hot Mic output. This connection is a 1/4-in (0.64 cm) phone jack. It
provides an output signal from the selected headset or panel
microphone. The Hot Mic output is always live. Audio from the mic is
routed through the Hot Mic output even if the mic is inactive (off).

Pin Function
Tip Mic
Ring IFB mute signal
Sleeve Ground
Table 2-7: Hot Mic pin out

Page 23
D SA [Stage Announce] line out (3-pin male XLR).

Pin Function
Pin 1 Ground
Pin 2 Positive
Pin 3 Negative
Table 2-8: SA pin out

E Program Input (3-pin female XLR).

Pin Function
Pin 1 Ground
Pin 2 Positive
Pin 3 Negative
Table 2-9: Program input pin out

F Line 1 (digital partyline). (3-pin male and female XLR connectors).

Pin Function
Pin 1 Ground
Pin 2 +30V DC and Audio
Pin 3 -30V DC and Audio
Table 2-10: Line 1 pin out

G Line 2 (digital partyline). (3-pin male and female XLR connectors).

Pin Function
Pin 1 Ground
Pin 2 +30V DC and Audio
Pin 3 -30V DC and Audio
Table 2-11: Line 2 pin out

H Slots for optional interface modules. For more information, see HMS-
4X Main Station rear panel: Interface modules.
I

Table 2-12: Key to HMS-4X Main Station rear panel diagram

Page 24
Warning: Only connect power supply to earthed supply sockets. Ensure that the
power supply is routed to avoid sharp bends, hot surfaces, pinches and abrasion.
For more safety guidance, see the Safety Instructions at the front of this guide.
Note: The HMS-4X Main Station does not have a power switch, button or key.
The system powers up when you connect the power supply.

HMS-4X Main Station rear panel: Interface modules


Up to three Interface modules (of the same or different types) can be fitted to the
extension bay of the Main Station. When looking at the rear of the Main Station,
expansion slot 1 is the left-hand slot, expansion slot 2 is the middle slot, and
expansion slot 3 is the right-hand slot.
Warning: The interface modules are NOT hot pluggable. Ensure that the
Main Station is powered down before inserting or removing modules.

Interface module Description


Two-wire interface This is a two channel device that enables interoperability
module (HLI-2W2) with, CellCom® / FreeSpeak®, and HME DX210 systems,
as well as both Clear-Com and RTS analog partyline
systems.
Note: This module requires a powered analog partyline.
The module provides two analog partyline connectors (3
pin female XLR connectors) with the following pin out:
Pin Function
1 Ground
2 Power [Option for RTS mode: power and
audio]
3 Audio
Table 2-13: two-wire Interface Module pin out
Use HelixNet Main Station menus to set the module for
either RTS or Clear-Com systems. If RTS mode is
selected, you can set either:
 Pin 2 for power to mixed audio channel (1 – 24)
 Pin 3 for power to mixed audio channel (1 – 24)
 Select either pin and assign required channel to it.

Page 25
Interface module Description
Four-wire interface This is a two channel device that enables interoperability
module (HLI-4W2) with the Eclipse® digital matrix system and other four-
wire audio sources such as telephone hybrids, AB-120/-
100, PA (Public Address) / SA (Stage Announce) systems.
The module also enables HelixNet-to-HelixNet
connections using four-wire audio ports. Two four-wire
connectors (EtherCON type RJ45 socket) are provided
with the following pin out:
Pin Function
1 RS-422 data TX+
2 RS-422 data TX-
3 Audio send +
4 Audio receive +
5 Audio receive -
6 Audio send -
7 RS-422 data RX+
8 RS-422 data RX-
Table 2-14: four-wire interface module pin out

Ethernet interface Enables linking of Main Stations, and connection of


module (HLI-ET2) Remote Stations and Speaker Stations via LAN. Contains
Two 10/100 Mbps RJ45 EtherCON ports.
Pin Name Function
1 TX+ Transmit Data+
2 TX- Transmit Data-
3 RX+ Receive Data+
4 n/c Not connected
5 n/c Not connected
6 RX- Receive Data-
7 n/c Not connected
8 n/c Not connected
Table 2-15: Ethernet interface module pin out

Warning: Both ports are configured to bridge


traffic from one port to the other in order to
work in a daisy-chained configuration.
Spanning Tree Protocol is not enabled on
these ports, therefore do not connect them
both to the same network.

Page 26
Interface module Description
Fiber interface Enables linking of Main Stations. Contains two SFP cage
module (HLI-FBS) slots. The module is supplied with one transceiver fitted.
Any 100BASE-X SFP can be connected.

Warning: Both ports are configured to bridge


traffic from one port to the other in order to
work in a daisy-chained configuration.
Spanning Tree Protocol is not enabled on
these ports, therefore do not connect them
both to the same network.
Table 2-16: HMS-4X Main Station rear panel: Interface Modules

Page 27
2.3 Remote Station rear panel

A B C D E F G H

Figure 2-4 HRM-4X Remote Station rear panel

Page 28
Key to Remote Station: rear panel
Feature Description

A PSU holder for a separate external AC-DC power supply. The external
PSU provides the 48V required and at its input takes 100-240V, 50-
60Hz.

B Power supply. The power input connector is a low voltage DC


connection. It is 48VDC at a max power of 12.95W.

C Line 1 (digital partyline). (3-pin male and female XLR


connectors).
Pin Function
Pin 1 Ground
Pin 2 +30V DC and Audio
Pin 3 -30V DC and Audio
Table 2-17: Line 1 pin out

D Power Over Ethernet (RJ45 connector)

E Control input/output (DB9 connector)


Pin Function
Pin 1 Audio out +
Pin 2 Audio in +
Pin 3 GND
Pin 4 Relay NC
Pin 5 Relay NO
Pin 6 Audio out -
Pin 7 Audio in -
Pin 8 Opto
Pin 9 Relay pole
Table 2-18 Control input/output pinout
The audio connections in this connector are wired directly to the SA
and program connectors. Only one or the other can be used at one
time.

F SA [Stage Announce] line out (3-pin female XLR).


Pin Function
Pin 1 Ground
Pin 2 Positive

Page 29
Key to Remote Station: rear panel
Feature Description
Pin 3 Negative
Table 2-19 SA pinout

G Program Input (3-pin m XLR).


Pin Function
Pin 1 Ground
Pin 2 Positive
Pin 3 Negative
Table 2-20 Program input pinout

H Hot Mic output. This connection is a 1/4-in (0.64 cm) phone jack. It
provides an output signal from the selected headset or panel
microphone. The Hot Mic output is always live. Audio from the mic is
routed through the Hot Mic output even if the mic is inactive (off).
Pin Function
Tip Mic
Ring IFB mute signal
Sleeve Ground
Table 2-21: Hot Mic pin out

Table 2-22: Key to Remote Station rear panel diagram

Page 30
2.4 Speaker Station

Figure 2-5 Speaker Station front panel

Page 31
Key to Speaker Station front panel
Feature Description
Tilt adjustable display screen. The following default information is
A
displayed:
 The channel label.
 The channel listen (volume) level.
For a full description of the display screen information, see Table 2-5
Main Station/Remote Station display icons and indicators.
In Menu mode, the display screens display the four levels of menu.
The menu hierarchy proceeds left to right:
 The top level menu is presented in the first screen (furthest left
on the front panel).
 The lowest level menu is presented in the fourth screen
(furthest right on the front panel).
If the display is in Menu mode, the display screen times out of Menu
mode and displays the channel label if no key is pressed for 20
seconds.
For more information about Menu mode, see 5.1 Using the Menus.
Rotary control. Turn to increase or decrease the listen volume level
B
for the channel, or to scroll menu items when in menu mode. To
select menu items, push the control.
Talk key. Press to talk on the channel and to all nodes (intercom
C
devices and systems) listening into the channel.
Loudspeaker / Headphone audio level rotary control [Main].
D
To increase the volume to the loudspeaker / headphones, turn
clockwise (up to 360°). To decrease the volume, turn counter
clockwise (up to 360°). As you increase or decrease the volume, the
level control LEDs pass through a range of indicator colors. For more
information, see Table 2-2 : Volume Indicator colors
Program feed audio level rotary control [PGM]. To increase the
E
volume of the program feed to the loudspeaker / headphones, turn
clockwise (up to 360°).
To decrease the volume, turn counter clockwise (up to 360°).
Call key. Press to send a call signal to all Keysets assigned to the
F
same Channel. There are two Call keys on the beltpack, one for each
of the displayed channels.
Headset socket (4-pin XLR–M)
G
Pin Function
1 Mic ground
2 Mic positive
3 Earphone ground
4 Earphone positive
Table 2-23 : Headset socket pin out

Page 32
Key to Speaker Station front panel
Feature Description
Headset/microphone key set. There is a keyset (set of controls) to
H
control the headset/microphone inputs and menu options. See Figure
2-6 Speaker Station keyset.
Gooseneck microphone connector (3-pin female Tuchel
I
connector)
Table 2-24 Key to Speaker Station front panel

Speaker Station front panel function buttons

A B

D C
Figure 2-6 Speaker Station keyset

Key to Speaker Station front panel function buttons


Feature Description

A Mic control [MIC ON]. Press to activate mic audio.

B Shift key. Press to display two alternative channels on the Speaker


Station displays.

C Menu. Press to display the Speaker Station menus in the display


screens. Use the rotary control for each display screen to scroll and

Page 33
Key to Speaker Station front panel function buttons
Feature Description
select menu items.

D Headset key [HSET]. Press to activate the headset mic. When the
headset is connected, the gooseneck microphone is disconnected.
Audio output to the loudspeaker is diverted to the headphones.
Table 2-25 Key to Speaker Station front panel keyset

Page 34
Speaker Station rear panel

Page 35
Speaker Station rear connectors
Digital Intercom

1 Not connected

2 Ground

3 Not connected

4 -30V DC and audio

5 +30V DC and audio

Power

1 Ground

2 48V DC

Page 36
S-Mount rear panel

Page 37
Key to S-Mount rear panel keyset
Feature Description

A Ethernet/Power over Ethernet connection (RJ45)

B Power connection.

C Line 1 Digital Party Line. (3-pin male XLR connector).


Pin Function
Pin 1 Ground
Pin 2 +30V DC and Audio
Pin 3 -30V DC and Audio
Table 2-26 Line 1 pinout

D Line 2 Digital Party Line. (3-pin female XLR connector).


Pin Function
Pin 1 Ground
Pin 2 +30V DC and Audio
Pin 3 -30V DC and Audio
Table 2-27 Line 1 pinout

Table 2-28 Key to S-Mount rear panel

Page 38
2.5 HBP-2X Beltpack
HBP-2X user controls (front and side view)

Figure 2-7: HBP-2X beltpack (front and side view)

Note: The beltpack has two Keysets, each containing one Call button (E) and one Talk
button (F).

Page 39
Key to HBP-2X user controls (front and side view)
Feature Description
E
A Menu key. Press firmly to enter Menu mode (see also D ). To
exit Menu mode, press the Menu key again.
The display screen times out of Menu mode and displays the channel
label(s) if no key is pressed for 20 seconds.

B USB 2.0 (Micro-AB) connector. For software upgrades.

C Casing. Metal casing for robust use. For information about the
beltclip, beltloops, and feet, see 2.5.3 HBP-2X beltclip, beltloops and
feet (base view).
Keyset

D Rotary control. Turn to increase and decrease the listen volume


level for the channel.
In Menu mode, you can turn either of the side-mounted rotary
controls to scroll menu items. To select (enter) items, press the right-
E
hand Call key (see ).

E Call key. Press to send a call signal to all Keysets assigned to the
same Channel. There are two Call keys on the beltpack, one for each
of the supported channels.
In Menu mode, press the right-hand Call key to select (enter) menu
items (see also A D ). Use the left-hand Call key to go back one
menu level.

F Talk key. Press to talk to all nodes (intercom devices and systems)
listening into the channel. There are two Talk keys on the beltpack,
one for each of the supported channels.

G Display screen. When the beltpack is not in Menu mode, the labels
and volume level for each of the two channels supported by the
beltpack are displayed on screen. For a full description of the display
screen information, see Table 2-5 Main Station/Remote Station
display icons and indicators.
Note: The beltpack has two Keysets, each containing one Call button
(E) and one Talk button (F).
Table 2-29: Key to HBP-2X Beltpack (front and side view)

Page 40
HBP-2X connectors and controls (rear view)

Figure 2-8: HBP-2X connectors and controls (rear view)

Key to HBP-2X Beltpack (Rear view)


Feature Description

A Line (Digital Partyline) (3-pin female XLR connector).

Pin Function
1 Ground
2 +30V DC and Audio
3 -30V DC and Audio
Table 2-30: Line (female) pin out

B Line (Digital Partyline) (3-pin male XLR connector). Pass-through


for daisy chain connection (see Figure 3-2: Example system
topologies (layouts)).

Pin Function
1 Ground
2 +30V DC and Audio
3 -30V DC and Audio
Table 2-31: Line (male) pin out

Page 41
Key to HBP-2X Beltpack (Rear view)
Feature Description

C Program feed (volume) control wheel. Turn to increase or


decrease the overall listen volume level of the program feed. To
assign programs to a channel, see 5.4.2 Assigning the Program
Listen to a channel and 14.1.5 Editing the Program Input

D 2.5 mm TRS headset input.

Function

Tip Audio +

Ring Audio -

Sleeve Ground

E Headset connector (4-pin male or 5-pin female XLR connector).

Pin Function

1 Mic ground

2 Mic positive

3 Earphone ground

4 Earphone positive

Table 2-32: 4-pin headset socket pin out

Pin Function

1 Mic ground

2 Mic positive

3 Earphone ground

4 Earphone right

5 Earphone left

Table 2-33: 5-pin headset socket pin out

Table 2-34: Key to HBP-2X Beltpack connectors and controls (base view)

Page 42
HBP-2X beltclip, beltloops and feet (base view)

Figure 2-9: HBP-2X Beltpack: base view

Key to HBP-2X Beltpack (Base view)


Feature Description

A Beltclip. The beltclip is secured to the unit with three screws, and
may be removed, according to your requirements.

B Feet (positions only). The beltpack can also be placed on a level


surface (once the beltclip has been removed). To give the beltpack
more grip on the surface, attach the four rubber feet supplied with
the beltpack.

C Beltloops (one either side). Use to thread through a belt or strap


for securing the beltpack to a belt or a fixed position.
Table 2-35: Key to HBP-2X Beltclip, beltloops and feet (base view)

Page 43
3 Installing HelixNet Partyline
This chapter describes how to install your HelixNet Partyline system. It also
provides basic guidance on planning your installation.
For related information, see 23 Cabling reference and the Powerline cable
distance calculator at:
http://www.clearcom.com/userfiles/file/Software/HelixNetCablingCalculator/index
.html#/

Tip: For guidance on connecting HelixNet Partyline to other systems, using the
optional interface modules, see 18 Connecting to Other Intercom Systems.

Do not plug any non-approved equipment into HelixNet Partyline.


HelixNet Partyline operates at different voltage levels than analog
two-wire partyline systems. Do not plug any analog two-wire
partyline equipment into the HelixNet partyline ports, as this may
cause damage.
For more safety instructions, see 1.1 Important Safety
instructions.

Page 44
3.1 Planning your HelixNet Partyline installation
Comparing digital with analog cabling

Figure 3-1: Analog and digital cabling comparison


Note: The program is always a participant within a Channel and cannot exist outside of a Channel.

Page 45
Key to analog and digital cabling comparison diagram
Feature Description
Example 4-channel analog Main Station (MS-704 shown).
A

HMS-4X Main Station (digital Main Station).


B

P1 Partyline channel 1

P2 Partyline channel 2

P3 Partyline channel 3

P4 Partyline channel 4
PF
Program Feed
Note: The program is always a participant within a Channel and
cannot exist outside of a Channel.
In a traditional analog partyline system, one cable is dedicated to
C each partyline channel. This can make it more difficult to build
redundancy or spare capacity into the installation (owing to the
number of connectors / cables dedicated to the delivery of channels).
In the HelixNet system, one cable can carry multiple channels.
D Because one cable can carry all channels, the second connector for
each line can either be used for redundancy (flybacks) or for future
extensions / changes to the cabling topology (layout).
Example analog partyline devices including RS-701 beltpacks. Analog
E
beltpacks must be re-cabled to use alternative channels, requiring the
physical re-location of cabling for new configurations.
To aid switching, Clear-Com sells additional switching equipment (the
SB-704 and RCS-2700 devices). The RS-702 (6-pin XLR) beltpack
requires the YC-36 splitter / combiner to combine 2 channels into a
6-pin configuration, and multi-conductor cables.
The RS-703 (3-pin XLR) beltpack requires a TWC-701 device to
combine 2 Clear-Com channels in a single twisted pair.
Example analog partyline devices including HBP-2X Beltpacks. Digital
F beltpacks can support any two of the partyline channels (plus
Program Feed), wherever they are physically located on the system.
New configurations of beltpacks and channels can be deployed
without the physical relocation of assets.
Table 3-1: Key to analog and digital cabling comparison diagram

Page 46
Note: The capabilities of different cable types may impact how far away beltpacks can
be placed from the Main Station, and the topologies you use. For more
information about cabling, see 23 Cabling reference.

Topologies
HelixNet Partyline can be deployed using a wide range of topologies, both
complex and straightforward. The following table describes three standard types
of topology:

Topology Description
Daisy-chain In a daisy-chain topology, the Main Station is connected to
the first unit. The units are then connected in a series,
using the pass-through connector on the back / rear of the
device to pass on the connection. No termination is
required.
Daisy-chains can be either linear or loop back to the Main
Station to form a ring for redundancy.
Star In a star topology, the Main Station is connected to a
passive (Y) splitter such as an XLR Bulkhead or Mult-box.
The units are then connected to the splitter point-to-point.

Tree A tree topology is a more complex version of the star


topology, using serially connected passive ( Y ) splitters.
The units are connected to each splitter point-to-point
(forming a branch of the tree).

Table 3-2: Topology types

Page 47
Figure 3-2: Example system topologies (layouts)

Page 48
Key to example system topologies (layouts) diagram
Feature Description
HMS-4X Main Station (digital Main Station) (rear panel).
A
There are two lines (digital partylines) on the Main Station, each of
which can support up to 10 digital HBP-2X beltpacks. There are two
connectors (3-pin XLR, male and female) for each line.
Daisy chained HBP-2X Beltpacks. To create a ‘daisy chain’ of
B connected beltpacks:
Connect the first beltpack to the Main Station, using either of the 3-
pin XLR connectors (female or male) on the base of the beltpack.
Pass on the connection to the second beltpack, using the remaining
connector as the pass through.
Repeat for all beltpacks (up to 10) in the chain. No cable termination
is required.
You can locally power an HRM or HKB within a daisy chain. This
prevents the normal draw off the powerline by the locally powered
device.
The second layout uses an XLR Bulkhead and a Mult-box (passive (Y)
C
splitters) to combine:
A daisy chain (with optional redundancy flyback).
Point-to-point connected beltpacks (using the Mult-box).
The complexity and variety of layouts does not restrict physical
access to channels.
Because HelixNet Partyline is a digital system, the HelixNet Stations
can access any of the available channels (plus a Program Feed),
however they are connected to the Main Station (see Figure 3-1:
Analog and digital cabling comparison).
Table 3-3: Key to example topologies (layouts)

Page 49
3.2 Installing the Main Station/Remote Station
The Main Station/Remote Station is a 19” 1RU-height device that you can install
to either:
 A standard 19” rack.
 A shelf, cabinet or other flat surface.

Main Station power up


There is no power switch, button or key on the Main Station. To power up the
unit:

1) Connect the power cord to the power supply connector on the Main
Station.
Note: The Main Station has a cable retaining clip to secure the power
cord. The retaining clip is detached for shipping and must be
refitted.
Note: For the location of the power supply connector, see A in Table
2-12: Key to HMS-4X Main Station rear panel diagram and
Table 2-22: Key to Remote Station rear panel diagram.

2) Connect the power cord to the power source. The unit requires an input
voltage between 100 - 240 VAC / 50-60Hz/ 250 watts / T 3.15A H 250 V.

Only connect power supply to earthed supply sockets. Ensure that the power
supply is routed to avoid sharp bends, hot surfaces, pinches and abrasion.
For safety guidance, see the Safety Instructions at the front of this guide.

Remote Station power up


The Remote Station is powered by an external power source. This can be:
 An external power supply (supplied)
 Power over Ethernet (PoE)
Note: To use PoE, you must connect a third-party PoE switch between
the Remote Station and the Main Station.
 From the Main Station digital power line

Page 50
3.3 Installing the Speaker Station
The Speaker Station can be installed either:
 Mounted in an S-Mount bracket for desktop use
 Mounted in an S-Mount bracket for installation on a wall
 Mounted inside a NEMA standard 4-gang wall box.
Note: The S-Mount bracket is an optional item ordered separately.

Speaker Station in an S-Mount bracket

Figure 3-3 Speaker Station in S-Mount bracket


You can adjust the S-Mount bracket by pressing one of the release buttons on
either side of the bracket. You can adjust the bracket in 10-degree steps from 80
degrees to horizontal. Indicators are present beside the release buttons that show
the adjustment steps.
To install the Speaker Station:

1) Connect a powerline XLR-3 port on the Speaker Station to a powerline


XLR-3 port on a Main Station.
Or
Connect an Ethernet port on the Speaker Station to an Ethernet port on
an HMS-4X HLI-ET2 option module.

Page 51
2) Connect a headset or microphone to the Speaker Station.

3) Connect power supply to the DC power port on the Speaker Station. (Not
necessary if using Powerline or PoE.)

Speaker Station in an S-Mount bracket wall installation


When the Speaker Station is fully closed, you can mount it on a wall using the
rear keyholes:

1) Space the wall screws to match the distance between the rear keyholes.
See Figure 3-4.

2) If necessary, remove the Speaker Station from the S-Mount bracket.

3) Hang the S-Mount bracket on the wall screws.

4) Tighten the wall screws.

5) Install the Speaker Station.

Figure 3-4 S-Mount bracket with keyholes

Speaker Station mounted inside a NEMA standard 4-gang


wall box
To connect the Speaker Station:

1) Connect the Digital Intercom screw terminals on the Speaker Station to a


powerline XLR-3 port on an HMS-4X.
Or

Page 52
Connect the Ethernet port on the Speaker Station to either the IP network
in which the HMS resides or directly to one of the Ethernet ports on the
HMS.

2) Connect a headset or microphone to the Speaker Station.

3) If required, remove the connector from the optional power supply and
connect the power supply to the Power screw terminals on the Speaker
Station.

Page 53
3.4 Installing the HBP-2X Beltpacks
The HBP-2X Beltpack is a device that you can:
 Wear at your belt using the beltclip.
 Install to a shelf or other flat surface.
 Attach to a pole or other fixed upright position.
For more information, see 2.5.3 HBP-2X beltclip, beltloops and feet (base
view)

Power up
The HBP-2X Beltpack is powered from the standard mic cable that connects the
device with the HMS-4X Main Station (see below).

Connecting the HBP-2X Beltpack to the Main Station


To connect the HBP-2X Beltpack to the Main Station:

1) There are two powerline connections on the Main Station which can each
support up to 10 digital HBP-2X beltpacks. There are two connectors (3-
pin XLR, male and female) for each line.

Connect the cable to the selected connector on the Main Station.


Note: For the location of Lines 1 and 2 (the powerlines) on the Main
Station, see F G in Figure 2-3: HMS-4X Main Station: rear
panel

2) Connect the cable to the beltpack, using one of the two 3-pin XLR
connectors (male and female) on the base / rear of the beltpack.
For example topologies, see 3.1.2 Topologies.

3.5 HelixNet infrastructure


This section contains guidelines for using HelixNet infrastructure components
including cables, connectors, splitter boxes and patch panels. HelixNet digital
partyline uses cable infrastructure to transport audio and data over a range of
frequencies. The maximum frequency used for transmission is approximately
25MHz. Depending on the amount of audio and data transmitted, HelixNet digital
partyline can work with as much as 90dB signal attenuation. However, the
receivers are very sensitive and are susceptible to crosstalk between cables.
Therefore it is important to maintain cable shield integrity through all
connectors, splitter boxes and patch panels.
The symptoms of crosstalk are:

Page 54
 Main Station front panel LINE LED indicator turns amber or red
 Beltpacks, Remote Stations and Speaker Stations take longer than usual
to boot and connect.
 Beltpack, Remote Station and Speaker Station front panel signal strength
indicators show lower than usual signal strength (zero or one bar).
 Main Station diagnostics screen (Diagnostics->Powerlines) indicates
collisions or errors on the line.

Cables and connectors


Clear-Com recommends the following shielded cables:

Microphone cables
Belden 9207 and 9463F with the two main conductors connected to XLR pin 2 and
3 and the drain wire to pin 1.

Cat cables
Belden 1351A or 1533P with the following connections at the XLR connector:

Cat5/5e/6 XLR
White/Orange 1
Orange 1
White/Green 3
Blue 2
White/Blue 3
Green 2
White/Brown 3
Brown 2
Shield/Drain 1

It is important to connect the cable shield or drain wire to the XLR pin 1
to maintain the shield integrity throughout the cable and connector.
Note: The total amount of cable deployed for a digital intercom line contributes to the
total capacitance of the line, even though some cables might not have a Beltpack
connected at the other end. The more capacitance there is, the more attenuation
there will be. Clear-Com recommends that you use the minimum amount of cable.
For example, daisy-chain or split a cable at the far end, close to the Beltpacks,
rather than make two homeruns to a central patch panel.

Patch panels
Clear-Com recommends XLR patch panels. These should be made of 3 pin XLR
feed-through adapters (for example, Neutrik NA3MDF) that maintain shield
Page 55
integrity from the back to the front. These adapters also enable easier rewiring of
the back or the front of the panel.

Splitter boxes
Ensure that you split the digital intercom lines within a shielded enclosure. For
example, a 1RU shielded chassis, such as Middle Atlantic CH1, and daisy-chained
XLR connectors (for example, Neutrik NC3MD or NC3FD).
To prevent crosstalk between lines, ensure that each shielded splitter box
contains only one digital intercom line. If you have to split more than one digital
intercom line, use multiple shielded enclosures.

POWER LINE #1A

POWER LINE #1A


WALL PLATE

POWER LINE #1B

POWER LINE #1B


WALL PLATE

For more information on cabling see 23.3 Cable connections

3.6 Converting analogue partylines to HelixNet


Many partyline installations use daisy-chained power terminal blocks to passively
split analog partylines. This way of splitting works relatively well for one HelixNet
Main Station. But because the cable shielding through those blocks is not
maintained, it makes the communication much more sensitive to interference.
Also, crosstalk occurs if two or more Main Stations use terminal blocks that are
close to each other.
To maintain shield integrity, Clear-Com recommends that you:
 Place existing terminal blocks in shielded and grounded enclosures
Or
 Replace the terminal blocks with shielded and grounded XLR splitter
boxes and XLR patch panels.

Page 56
4 IP Network Structure

4.1 Network connections


Connecting in an existing IP network requires planning with your IT department in
order to plan the IP addressing scheme. By default HelixNet Main Station uses
automatic IP addressing (DHCP) enabled. In order for that to work properly in an
existing IP network there must be a DHCP server handing out IP addresses. If no
DHCP server is found, a Main Station will revert to an unused link-local address in
the 169.254.0.0/16 block. (See 4.3 Link Local Environments for more
information).
Through the Networking menu on the devices, you can disable DHCP and set
static IP addresses.
Note: For HelixNet 3.0 and above, it is not necessary to be on the same Subnet, the
devices will link across your LAN.

Figure 4-1: Network connections

Page 57
4.2 Multiple Groups in the same IP Network
Multiple groups in the same network can be achieved by having multiple Link-
Masters. Each Link-Master will head a group of Main Stations and will not interfere
with other groups.

Networking Specifications
Specification Value
Latency on Powerline 40-80ms (Depends on cable type and length, and
how many devices are connected. The greater the
number of devices, the greater the latency.)
Latency over IP Network 30ms + Network Latency (Main Station to Main
Station)
Bandwidth used 300 kbps per active Talker, for a maximum of 1
talker per device in the system
Each Beltpack and Speaker Station counts as 1
device
Each Main Station and Remote Station counts as 2
devices
IP version IPv4
Table 4-1 Networking specifications

4.3 Link Local Environments


What is link-local?
A link-local address is an IP address within the local segment of any network.
Routers do not pass information to these as link-local addresses are not
guaranteed to be unique beyond a single network segment. When first connected
to a network, your HelixNet device will attempt to get an IP address via Dynamic
Host Configuration Protocol (DHCP). If no DHCP server is available the unit will
automatically enter link-local IP mode. A link-local IP address will take the form:
169.254.xxx.xxx.

Working with a device in link-local mode


Devices will revert to link-local mode if they are configured to DHCP and fail to
find a DHCP address on the network or device they are attempting to connect to.
Any DHCP enabled device connected directly to a device in link-local using a
standard Ethernet cable will enter link-local mode automatically.

Page 58
Note: The units will operate in link-local, but for optimum performance it is
recommended that they are used with either static or DHCP network settings. In
link-local, the address will change each time the device reboots resulting in
potential loss of connection to endpoints
The easiest way to take a HelixNet device out of link-local mode is to allocate a
new IP address to the unit from the device front menus. Please ensure with your
network administrator that there will be no IP clashes with this address.

Change the IP address of a HelixNet device from the


device front menu screens
To change a unit’s IP address, you must first disable DHCP. Press the Menu
button on front of device to enter Menu mode.

1) To enable or disable DHCP:


a) In Menu mode, select Networking.
Note: The Networking menu only appears if an Ethernet or Fiber
interface module is detected.
b) From the second menu, select Preferences.
c) From the third menu, select DHCP.
d) From the fourth display screen, select one of the following:
 Disabled
 Enabled (default)

2) To edit the IP address:


a) In Menu mode, select Networking.
Note: The Networking menu only appears if an Ethernet or Fiber
interface module is detected.
b) From the second menu, select Preferences.
c) From the third menu, select IP Address.
d) From the fourth display screen, edit the IPv4 address.
Note: The HelixNet system uses a 10.0.0.x IP address range internally
between the Main Station and the Beltpacks, and therefore will not
allow setting the external IP address to anything in that range.

Page 59
Note: If you change the IP address (either manually or through DHCP),
the link between stations will be broken and you have to reboot
the Main Station to link again. The following message will appear
as a banner (inverted text) at the bottom across the four displays
on the Main Station
IP address | changed, | reboot | to link
If that message appears, pressing the Menu key will bring you
directly to: Administration->Reset->Reboot->Reboot Now

Accessing the Core configuration Manager (CCM) of a


HelixNet unit in link-local mode
As an alternative to configuring your device from the front menu screens you can
use the browser based CCM.
To access the CCM of a HelixNet unit in link-local, you must connect to it from a
computer that is also in link-local mode.
A computer can be put into link-local mode by ensuring it is in DHCP mode and
connecting it to the unit that is in link-local with a standard Ethernet cable. The
computer will look for a dynamically generated IP address (DHCP), and when it
does not find one will enter link-local mode automatically.
Once the computer is connected to the HelixNet device and in link-local mode,
you can connect to your unit by opening a browser window on the computer and
inputting the unit’s IP address (from the front panel display) into the address
field. This takes you to the Core Configuration Manager where you can configure
the device as usual. See 13 Core Configuration Manager (CCM) for more detail.
Note: The units will operate in link-local, but for optimum performance it is
recommended that they are used with either static or DHCP network settings.

Page 60
5 Configuring and managing the Main Station
from device menus
This chapter describes how to configure the settings and manage the Main Station
using Menu mode. It also shows you how to monitor and diagnose performance
issues, using the Diagnostics menus.
Tip: For a quick reference to the Main Station menus, see 21 Menu maps.

5.1 Using the Menus


To place the Main Station in Menu mode, press the Menu key to the left of the
first display screen.
In Menu mode, the display screens display the four levels of menu. The menu
hierarchy proceeds left to right:
 The top level menu is presented in the first screen.
 The lowest level menu is presented in the fourth screen (furthest right
on the front panel).
Note: If Menu mode is locked, you must unlock the menus from CCM before
you can enter the menu. See section 6.

Configuring settings
To configure settings:

1) For each menu, turn the rotary control clockwise to scroll down the
menu items. Turn counter clockwise to scroll up the menu items.
Off-screen menu items are indicated by arrows at the top and/or bottom
of the screen.
Selected menu items (which create your path through the four menus)
are highlighted in solid yellow.
The fourth menu displays the settings that relate to your previous menu
choices (system features or functionality).
The current setting is indicated by a dotted box around the menu item

2) When you have selected a setting by rotating the right hand rotary
control, press that rotary control to enable the setting on the Main
Station.

Exiting Menu mode


To exit menu mode press the menu key.

Page 61
Note: If no key is pressed for 20 seconds, the menu will time out and display screens
will revert to their normal mode of operation.

Page 62
5.2 Configuring the Audio settings
Audio settings for the headset
To configure the audio settings for the headset:

1) In Menu mode, select Audio Settings and then Headset.

2) To adjust the level of sidetone on the headset:


a) In the third menu, select Sidetone Gain.
b) In the fourth menu, select one of the following:
 0dB
 - 6dB
 - 12dB (default)
 - 18dB
c) To enable (confirm) the selected setting, press the rotary control.

3) To limit the audio level delivered to the headphones (or to disable


headphone limiting):
a) In the third menu, select Headphone Limit.
b) In the fourth menu, select one of the following:
 Off
 +6dB
 0dB (default)
 - 6dB
c) To confirm the selected setting, press the rotary control.
Note: When Headphone Limit is set to anything but Off, a LIM indication
will be shown on the leftmost display.

4) To set the Headphone Gain:


a) In the third menu, select Headphone Gain.
b) In the fourth menu, select one of the following:
 OdB (default)f
 +3dB
 +6dB
 +9dB
 +12dB
Page 63
c) To confirm the selected setting, press the rotary control.

5) To set (or disable) sidetone tracking on the headset:


a) In the third menu, select Sidetone Control.
b) In the fourth menu, select one of the following:
 Tracking - The sidetone volume will follow (track) the Main
volume level.
 Non-Tracking - The sidetone volume is set to maximum.
 Disabled - Sidetone is disabled.
Note: The default is Tracking.
c) To confirm the selected setting, press the rotary control.

6) To select the type of microphone on the headset:


a) In the third menu, select HS Mic Type.
Note: HS = Headset.
b) In the fourth menu, select either of the following types of
microphone:
 Electret (-15dB)
 Dynamic (0dB) (default)
 Dynamic (-10dB)
c) To confirm the selected setting, press the rotary control.

Audio settings for the microphone


To configure the audio settings for the microphone:

1) In Menu mode, select Audio Settings and then Microphone.

2) To select the Headroom:


a) From the third menu, select Headroom.
b) From the fourth menu, select one of the following:
 Normal (default)
 High - Reduces the analog input gain and increases the digital
gain accordingly. That reduces digital clipping at the A/D
converter but increases the noise floor. This setting is intended
for use in environments with very high background noise.

Page 64
3) To enable or disable the Contour Filter:
a) From the third menu, select Contour Filter
b) From the fourth menu, select one of the following:
 Enabled - The Contour filter is a Clear-Com algorithm
enhancing speech intelligibility, especially when whispering or
talking at a low volume.
 Disabled
Note: The default is Enabled.

Audio setting for the Program Input


To configure the label (name) for the Program Input (Program Feed) gain:

1) In Menu mode, select Audio Settings and then Program Input.

2) From the third menu, select Label.

3) From the fourth menu, select the existing label by scrolling to it and
pushing the rotary controller. Edit the label by rotating the controller to
scroll through letters and digits and pushing to select a letter/digit.

4) When you have done, scroll to Save and push the rotary controller. To
exit without saving changes, go back to the third screen.

To configure the audio setting for the Program Input (Program Feed) gain:

5) In Menu mode, select Audio Settings and then Program Input.

6) From the third menu, select Gain.

7) From the fourth menu, select one of the following:


 + 12dB
 + 6dB
 0dB (default)
 - 6dB
 - 12dB

8) To confirm the selected setting, press the rotary control.

Page 65
9) The GPO trigger activates a relay when receiving a call or activating a talk
on a partyline channel. You can enable or disable the GPO trigger. To
configure the audio setting for the GPO trigger:

1) In Menu mode, select Audio Settings and then Program Input.

2) From the third menu, select GPO Trigger.

3) From the fourth menu, select one of the following:


 Enabled (default)
 Disabled

4) To confirm the selected setting, press the rotary control.


Note: You can also configure the GPO trigger using Menu Mode >
Modules Settings.
To select the VOX:

1) From the third menu, select VOX.


a) From the fourth menu, select one of the following:
 Enabled
 Disabled (default)

2) To confirm the selected setting, press the rotary control.


To select the VOX Off Delay:

1) From the third menu, select VOX Off Delay.

2) From the fourth menus, select one of the following:


 .5 sec (default)
 1 sec
 2 sec
 3 sec
 4 sec

3) To confirm the selected setting, press the rotary control.

Audio settings for Program IFB [Interruptible Foldback]


IFB allows you to temporarily interrupt the continuous program listen (program
feed) and speak to the channels connected to the program listen. This applies to a
Channel to which the Program Input is assigned. If any participant within the

Page 66
channel talks, the program is dimmed. See also 5.4.2 Assigning the Program
Listen to a channel.
To configure the audio settings for Program IFB [Interruptible Foldback]:

1) In Menu mode, select Audio Settings and then Program IFB.

2) From the third menu, select IFB Dim Level.


Note: The IFB Dim Level determines the amount that the volume level of
the Program Level is reduced by when it is interrupted by the IFB.

3) From the fourth menu (fourth display screen), select one of the following:
 IFB Disabled (default)
 - 6dB
 -12dB
 -18dB
 -24dB
 Full Cut

4) To confirm the selected setting, press the rotary control.

Audio settings for the SA [Stage Announce] Output


To configure the audio settings for the SA [Stage Announce] Output:

1) In Menu mode, select Audio Settings and then SA Output.

2) From the third menu, select Gain.

3) From the fourth menu, select one of the following:


 + 12dB
 + 6dB
 0dB (default)
 - 6dB
 - 12dB

4) To confirm the selected setting, press the rotary control.

Page 67
Audio settings for the Hot Mic Output
To configure the audio settings for the Hot Mic Output:

1) In Menu mode, select Audio Settings and then Hot Mic Output.

2) From the third menu, select Gain.

3) From the fourth menu, select one of the following:


 + 12dB
 + 6dB
 0dB (default)
 - 6dB
 -12dB

4) To confirm the selected setting, press the rotary control.

Audio settings for the Front Panel


To configure the audio settings for the Front Panel:

1) In Menu mode, select Audio Settings and then Front Panel.

2) From the third menu, select Loudspeaker Dim.

3) From the fourth menu, select one of the following:


 0 dB
 -3 dB
 -6 dB (default
 -12 dB
 -24 dB

4) To confirm the selected setting, press the rotary control.

Page 68
5.3 Selecting Station Settings
Setting Preferences
To set the Preferences:

1) In Menu mode, select Station Settings and then Preferences. You will
see Roles in the third menu.

2) From the fourth menu, select the required Role. Select local config if you
do not wish to use a role.

3) To confirm the selected setting, press the rotary control.

Setting Keyset Assignments


To set the Keyset Assignments:

1) In Menu mode, select Station Settings and then Keyset Assign.

2) From the third menu, select required Keyset (1 – 4).

3) From the fourth menu, select a Channel (1 – 24) to assign to the Keyset.

4) Repeat this procedure for the remaining Keysets.

5) To confirm the selected setting, press the rotary control.

Setting key latching


To enable or disable front panel keys for latching:

1) In Menu mode, select Station Settings and then Keysets.

2) From the third menu, select either:


Key(s) Description
Talk #1 Talk keys for the four available channels.
Talk #2
Talk #3
Talk #4
SA Out key Key used to talk to a connected public address or
Stage Announce (SA) system.

Table 5-1: Setting key latching

Page 69
Note: The All Talk and RMK (Remote Mic Kill) key are also displayed in
the list. Those keys cannot be latched. To find out how to
configure the RMK and All Talk keys, see 5.3.5 Setting the All
Talk key.
Note: The All Talk key allows you to talk to all Channels at once with
the push of a button. Select All Channels to talk to all 12 (or 24
according to license) Channels on your system. Select Visible
Channels to talk to the Channels visible on your four device
Keyset screens.

3) In menu mode select Station Settings and then Keysets.

4) From the third menu, select All Talk.

5) From the fourth menu, select All Channels or Visible Channels.

6) To confirm the selected setting, press the rotary control.

Setting the RMK (Remote Mic Kill) key.


Tip: For a quick reference to the location of keys on the front panel, see
2.1Main Station/Remote Station: Front panel.

1) In menu mode select Station Settings and then Keysets.

2) From the third menu, select RMK.

3) From the fourth menu, select either of the following:


 All Channels
 Visible Channels
 Disabled

4) To confirm the selected setting, press the rotary control.


Note: Select All Channels to close the microphone on all 12 (or 24 according to
license) Channels on your system. Select Visible Channels to close the
microphone to the Channels visible on your four device Keyset screens.

Setting the All Talk key


The All Talk key allows you to talk to all Channels at once with the push of a
button. Select All Channels to talk to all 12 (or 24 according to license) Channels

Page 70
on your system. Select Visible Channels to talk to the Channels visible on your
four device Keyset screens.

1) In menu mode select Station Settings and then Keysets.

2) From the third menu, select All Talk.

3) From the fourth menu, select All Channels or Visible Channels.

4) To confirm the selected setting, press the rotary control.

Setting the RMK (Remote Mic Kill) key


The RMK (Remote Mic Kill) key is used to:
 Deselect any latched keyset Talk routes.
 Turn off any latched Talk on connected analog partyline equipment.
To enable or disable the RMK (Remote Mic Kill) key:

1) In Menu mode, select Station Settings and then Keysets.

2) From the third menu, select RMK.


Note: Talk Latch and the SA Output Key are also listed in this menu.
See 5.3 Selecting Station Settings.

3) From the fourth menu, select either of the following:


 All Channels (12 or 24 according to license)
 Visible Channels (default)
 Disabled

4) To confirm the selected setting, press the rotary control.

Setting display screen brightness


By default, the display screens are set for medium brightness. To set the
brightness of the display screens:

1) In Menu mode, select Station Settings and then Display.

2) From the third menu, select OLED Brightness.

Page 71
3) From the fourth menu, select one of the following brightness settings:
 High
 Medium (default)
 Low

4) To confirm the selected setting, press the rotary control.

Setting key brightness


By default, the front panel keys are set to High / Low. To set the brightness of
all front panel keys:

1) In Menu mode, select Station Settings and then Display.

2) From the third menu, select Key Brightness.

3) From the fourth menu, select one of the following brightness settings:
Key(s) Description
High / Low The default setting.
Keys are lit bright when active and lit dim when
inactive.
High / Off Keys are lit bright when active and are unlit when
inactive.
Low / Off Keys are lit dim when active and are unlit when
inactive.
Off / Off Keys are unlit, whether or not they are active or
inactive.
Table 5-2: Setting key brightness

4) To confirm the selected setting, press the rotary control.

Setting the screensaver


The screensaver features the channel label and is enabled by default. The display
screens enter screensaver mode when the Main Station has been inactive for 10
minutes.
Tip: To exit screensaver mode, press any key on the front panel.
To enable or disable the screensaver:

1) In Menu mode, select Station Settings and then Display.

2) From the third menu, select Screensaver.

Page 72
3) From the fourth menu, select either:
 Channel Name (default)
 Hostname
 Role Name
 Blank
 Disabled

4) To confirm the selected setting, press the rotary control.

Page 73
5.4 Configuring the channel settings
Editing the channel label
The maximum length for a channel label is 12 characters.. To edit the channel
label:
Note: Channel labels will be dictated by the Link Master when Main Stations are linked.

1) In Menu mode, select Channels and then the name of the channel you
want to edit.

2) From the third menu, select Label.

3) Select Clear and press the rotary control to clear the channel label.

4) In the fourth menu, the following prompt is displayed above the channel
label:
[Press to edit]
Press the rotary control.

5) The first letter of the channel label is shown as selected. The following
prompt is displayed above the channel label:
[Scroll / Press to Select]
Scroll to the character you want to edit by turning the rotary control. To
begin editing, press the rotary control.

6) The character you have selected for editing is shown in a box with a
dotted border.
To display alternative characters in the box, turn the rotary control. The
range of available characters comprises the following:
Characters Description / range
Numbers 0 to 9
(numeric)
Letters Capital letters = A to Z
Small letters = a to z
Symbols # & *() -_=+ /!@ :
Note: You can also select a space.

Table 5-3: Channel label characters


To select a character, press the rotary control.

Page 74
7) When you have selected a replacement character, scroll to the next
character you want to edit. When you have finished editing the channel
label, scroll to Save (displayed beneath the channel label).
To save the channel label, press the rotary control.

Assigning the Program Listen to a channel


To assign (or unassign) the Program Listen (Program Feed) to a channel:

1) In Menu mode, select Channels and then the name of the channel.

2) From the third menu, select Program Listen.

3) From the fourth menu, select either None, or choose from the list of
available programs.
Note: The default is None.

4) To confirm the selected setting, press the rotary control.


Tip: When you assign the Program Listen to a channel, PGM is displayed on the
display screen (under the listen level bar, to the left) for that channel.

Assigning a GPO relay to a channel


You can assign a relay that is triggered on receiving a call or detecting a talk on a
partyline channel. To assign (or unassign) a relay:

1) In Menu mode, select Channels and then the name of the channel.

2) From the third menu, select GPO on Talk or GPO on Call.

3) From the fourth menu, select either None, or choose from the list of
available relays.
Note: The default is None.

4) To confirm the selected setting, press the rotary control.

Page 75
5.5 Configuring the Control I/O
The Control I/O connector (25 way female D-type) on the rear panel allows you to
connect up to 4 relay outputs or 4 opto inputs and control them through the Main
Station keysets:

I/O type Description


Opto inputs Opto inputs enable you to connect a foot switch or
other control device and use it to trigger Call or Talk
functions.
Relay outputs Relay outputs enable you to use Call or Talk keys to
trigger any external device that accepts a standard
contact closure (such as a theater curtain or an On
Air light, or the beltpack USB flasher).
Table 5-4: Opto inputs and Relay outputs

Configuring Opto inputs


To configure the Control I/O for Opto inputs:

1) In Menu mode, select Control I/O.

2) From the second menu, select Inputs.

3) From the third menu, select one of the following:


 Opto 1
 Opto 2
 Opto 3
 Opto 4

4) From the fourth menu (fourth display screen), select one of the following:
 None
 Call Key 1
 Talk Key 1
 Call Key 2
 Talk Key 2
 Call Key 3
 Talk Key 3
 Call Key 4
 Talk Key 4

Page 76
5) To confirm the selected setting, press the rotary control.

Configuring Relay outputs


To configure the Control I/O for Relay outputs:

1) In Menu mode, select Control I/O.

2) From the second menu, select Outputs.

3) From the third menu, select one of the four available Relay outputs:
 Relay 1
 Relay 2
 Relay 3
 Relay 4

4) From the fourth menu, select one of the following:


 None (default)
 Call Key 1
 Talk Key 1
 Call Key 2
 Talk Key 2
 Call Key 3
 Talk Key 3
 Call Key 4
 Talk Key 4
 SA Key
Note: The number of the key relates to the keyset to which it belongs
(for example, Call Key 1 is the Call key for the first keyset /
display screen).

5) To confirm the selected setting, press the rotary control.

Page 77
5.6 Configuring Module Settings
Up to three optional interface modules can be fitted to the expansion bay of the
HMS-4X Main Station.
Warning: The interface modules are not hot pluggable. Ensure that the
Main Station is powered down before inserting or removing modules.
The Menu mode > Module Settings are used to set up the interface modules.
Tip: For more detailed information about interface modules, including pin out
information, see: 2.2.1 HMS-4X Main Station rear panel: Interface modules.

Configuring a Four-wire interface module


The following procedure shows you how to configure the Module Settings for a
Four-wire interface module.
To configure the Module Settings for a four-wire interface module:

1) In Menu mode, select Module Settings.

2) From the second menu, select one of the two available ports on the two-
wire interface module:
Slot 2/Port A 4W
Slot 2/Port B 4W
Note: In this example, the four-wire module has been fitted to slot 2 in
the expansion bay. The expansion bay contains three slots.
4W = four-wire.

3) To associate one of the four available channels with the selected port, or
to disable channels associations:
a) From the third menu, select Channel Assign.
b) From the fourth menu, select one of the following:
 Disabled (default)
 Channel 1.
 Channel 2.
 Channel 3.
 Channel 4.
 …
c) To confirm the selected setting, press the rotary control.

Page 78
4) The Program Output allows a program feed associated with the channel
assigned to the four wire port to either be delivered to that 4 wire port
alongside the other channel audio or not. To set the Program Output:
a) From the third menu, select Program Output.
b) From the fourth menu, select one of the following:
 Unmute
 Mute (default)

5) To confirm the selected setting, press the rotary control.

6) To set the input level for the four-wire port:


a) From the third menu (third display screen), select Input Gain.
b) From the fourth menu (fourth display screen), select one of the
following:
 +12dB
 + 6dB.
 0dB (default)
 -6dB.
 -12dB
c) To confirm the selected setting, press the rotary control.

7) To set the output level for the four-wire port:


a) From the third menu, select Output Gain.
b) From the fourth menu, select one of the following:
 +12dB
 + 6dB.
 0dB (default)
 -6dB.
 -12dB

8) To confirm the selected setting, press the rotary control.

9) To set the GPO trigger for the Program Output:


a) From the third menu, select GPO.
b) From the fourth menu, select one of the following:
 Enabled
 Disabled
Page 79
10) If you are setting up a continuous audio (program) feed using the four-
wire interface module, then you may want to enable the VOX
functionality. To help reduce redundant noise, the VOX functionality
automatically deactivates and activates the continuous audio feed, at an
automatically determined volume threshold.
Note: If you assign a program and a four-wire interface to the same
channel, VOX is automatically enabled.
To enable or disable VOX:
a) From the third menu, select VOX.
b) From the fourth menu, select one of the following:
 Enabled.
 Disabled (default)
c) To confirm the selected setting, press the rotary control.

11) The VOX Delay OFF setting determines the length of time to wait before
deactivating the incoming audio. To set the VOX Delay OFF setting:
a) From the third menu, select VOX Delay OFF.
b) From the fourth menu, select one of the following:
 .5 sec (default)
 1 sec
 2 sec
 3 sec
 4 sec
c) To confirm the selected setting, press the rotary control.

Configuring a Two-wire interface module


The following procedure shows you how to configure the Module Settings for a
Two-wire interface module.
Note: The Two-wire interface module must receive power from the partyline.
To configure the Module Settings for a Two-wire interface module:

1) In Menu mode, select Module Settings.

Page 80
2) From the second menu, select one of the two available ports on the two-
wire interface module:
Slot 1/Port A 2W
Slot 1/Port B 2W
Note: In this example, the two-wire module has been fitted to slot 1 in
the expansion bay. The expansion bay contains three slots.
2W = Two-wire.
a) To associate one of the four available channels (or to disable
channels associations) with the selected port:
From the third menu (third display screen), select Channel Assign.
b) From the fourth menu, select one of the following:
 Disabled (default)
 Channel 1
 Channel 2
 Channel 3
 Channel 4
 …
c) To confirm the selected setting, press the rotary control.

3) The Program Output allows a program feed associated with the channel
assigned to the four wire port to either be delivered to that 4 wire port
alongside the other channel audio or not. To set the Program Output:
a) From the third menu, select Program Output.
b) From the fourth menu, select one of the following:
 Unmute (default)
 Mute

4) To confirm the selected setting, press the rotary control.

5) Auto-nulling helps to reduce echo while talking on a two-wire audio


system. To start Auto-nulling on the selected port:
a) From the third menu, select Auto-Nulling.
b) From the fourth menu, select Start.
Note: Auto-nulling is only applicable to two-wire audio. All Talk
routes/keys must be disabled before Auto-nulling can commence.
If an echo persists, ensure all Talk routes are disabled and re-null
the system.

Page 81
6) The Two-wire interface module is set for Clear-Com systems by default.
However, you can also set the two-wire ports for use with RTS analog
partyline systems. If you are connecting to an RTS system, you also have
a choice of two different pinouts:
RTS pinout option Description
RTS Audio Pin 2 Pin 2 is used for both power and audio.
RTS Audio Pin 3 Pin 3 is used for audio (Pin 2 is used for
power only).
Table 5-5: Configuring Module Settings: RTS pinout options
Note: For detailed pinout information, see 2.2.1 HMS-4X Main Station
rear panel: Interface modules.
To configure the port for either Clear-Com or RTS systems:
a) From the third menu, select Mode.
b) From the fourth menu, select one of the following:
 Clear-Com
 RTS Audio Pin 2
 RTS Audio Pin 3
c) To confirm the selected setting, press the rotary control.

7) To set the Input Gain:


From the third menu, select Input Gain.
From the fourth menu, select one of the following:
 +3 dB
 +2 dB
 +1 dB
 0 dB (default)
 -1 dB
 -2 dB
 -3 dB

Page 82
8) To set the Output Gain:
a) From the third menu, select Output Gain.
b) From the fourth menu, select one of the following:
 +3 dB
 +2 dB
 +1 dB
 0 dB (default)
 -1 dB
 -2 dB
 -3 dB

9) To set the GPO trigger for the Program Output:


c) From the third menu, select GPO.
d) From the fourth menu, select one of the following:
 Enabled
 Disabled

10) Enabling RMK [Remote Mic Kill] Input allows an external source such
as the main (base) station of the connected two-wire system to send an
RMK signal to the analog beltpacks attached to the HelixNet Main Station.
Note: If this is enabled and the analog party line system is powered
down, it will be interpreted by the HelixNet Main Station as an RMK
input and all talk routes will be switched off.
To enable RMK Input:
a) From the third menu (third display screen), select RMK Input.
b) From the fourth menu (fourth display screen), select one of the
following:
 Enabled
 Disabled (default)
c) To confirm the selected setting, press the rotary control.

11) Enabling RMK [Remote Mic Kill] Output allows you to send an RMK
signal from the HelixNet Main Station to the connected analog beltpacks.
To enable RMK Output:
a) From the third menu, select RMK Output.
b) From the fourth menu, select one of the following:
 Enabled
Page 83
 Disabled (default)
To confirm the selected setting, press the rotary control.

12) If you are setting up a continuous audio (program) feed using the two-
wire interface module, then you may want to enable the VOX
functionality. To help reduce redundant noise, the VOX functionality
automatically deactivates and activates the continuous audio feed, at an
automatically determined volume threshold.
Note: If you assign a program and a two-wire interface to the same
channel, VOX is automatically enabled.
To enable or disable VOX:
a) From the third menu, select VOX.
b) From the fourth menu, select one of the following:
 Enabled
 Disabled (default)
c) To confirm the selected setting, press the rotary control.

13) The VOX Delay OFF setting determines the length of time to wait before
deactivating the incoming audio. To set the VOX Delay OFF setting:
a) From the third menu, select VOX Delay OFF.
b) From the fourth menu, select one of the following:
 .5 sec (default)
 1 sec
 2 sec
 3 sec
 4 sec
c) To confirm the selected setting, press the rotary control.

Configuring an Ethernet or Fiber interface module


The following procedure shows you how to configure the Module Settings for an
Ethernet interface module.
To configure the Module Settings for an Ethernet interface module:

1) To view status information about Main Stations:


a) In Menu mode, select Networking.
Note: The Networking menu only appears if at least one Ethernet or
Fiber interface module is detected.

Page 84
b) From the second menu, select Stations. A list of station IDs is
given for each Main Station in the network. Each station ID in the
list is preceded by the letter M- for the Link-Master station itself and
S- for all Link-Member (S stands for Slave).
c) From the third menu select the required station ID.
d) From the fourth menu you can view the following:
 Status – Enabled or Disabled
 IP – The IP address.

2) To edit or change the Hostname for your device:


a) In Menu mode, select Networking.
b) From the second menu, select Preferences
c) From the third menu, select Hostname
d) From the fourth menu, select the name by pushing and turning the
Rotary controller.
e) Edit the name by turning the controller to select a letter or number
and pushing to select it. Then turn to scroll through letters. Push to
commit.
f) When you have done, scroll to SAVE and push to commit.

3) To enable or disable DHCP:


g) In Menu mode, select Networking.
Note: The Networking menu only appears if an Ethernet or Fiber
interface module is detected.
h) From the second menu, select Preferences.
i) From the third menu, select DHCP.
j) From the fourth display screen, select one of the following:
 Disabled
 Enabled (default)

4) To edit the IP address:


k) In Menu mode, select Networking.
Note: The Networking menu only appears if an Ethernet or Fiber
interface module is detected.
l) From the second menu, select Preferences.
m) From the third menu, select IP Address.

Page 85
n) From the fourth display screen, edit the IPv4 address.
Note: You can only edit the IPv4 address if DHCP is disabled.
Note: The HelixNet system uses a 10.0.0.x IP address range internally
between the Main Station and the Beltpacks, and therefore will not
allow setting the external IP address to anything in that range.
Note: If you change the IP address (either manually or through DHCP),
the link between stations will be broken and you have to reboot
the Main Station to link again. The following message will appear
as a banner (inverted text) at the bottom across the four displays
on the Main Station
IP address | changed, | reboot | to link
If that message appears, pressing the Menu key will bring you
directly to: Administration->Reset->Reboot->Reboot Now

5) To edit the Gateway:


a) In Menu mode, select Networking.
Note: The Networking menu only appears if an Ethernet or Fiber
interface module is detected.
b) From the second menu, select Preferences.
c) From the third menu, select Gateway.
d) From the fourth display screen, edit the gateway.
Note: You can only edit the gateway if DHCP is disabled.

6) To edit the Subnet Mask:


a) In Menu mode, select Networking.
Note: The Networking menu only appears if an Ethernet or Fiber
interface module is detected.
b) From the second menu, select Preferences.
c) From the third menu, select Subnet Mask.
d) From the fourth display screen, edit the Subnet Mask.
Note: You can only edit the Subnet Mask if DHCP is disabled.

7) To enable or disable linking:


a) In Menu mode, select Networking.
Note: The Networking menu only appears if an Ethernet or Fiber
interface module is detected.
b) From the second menu, select Linking.
c) From the third menu, select Link Mode.

Page 86
d) From the fourth display screen, select one of the following:
 Disabled (default)
 Master
 Member
e) If Member is selected, the menu asks you to pick a Link-Master to
connect to in the Networking>Link To Master menu. It can be done
by picking from a hostname list or by entering an IP address.

8) To enable a key Expansion Group:

When you connect HelixNet Main and Remote Stations in a key Expansion
Group relationship, you enable control of keysets on up to three stations
from one host device. This makes controlling larger systems much more
convenient. In order to set up an Expansion Group, the devices must be
on the same IP network, and able to see each other.

First, decide which device to designate as Host.


a) In Menu mode, select Networking.
Note: The Networking menu only appears if an Ethernet or Fiber
interface module is detected.
b) From the second menu, select Expansion Mode.
c) From the third menu, select Host.
d) From the fourth menu select Enabled. A stacking icon will flash on
the menu screen to indicate that the device is open for pairing.
e) From the device you wish to connect as an Expanded panel, in
Menu Mode, select Networking.
f) From the second menu, select Expansion Mode.
g) From the third menu, select Expand to Host.
h) From the fourth menu, select the Host device, which should be
visible by name.
i) This connects the devices in a key Expansion relationship.
When an Expansion Group is successfully established, a steady stacking icon
will appear in the menu screens of the devices.

Viewing the Module Settings: Version information


The software (firmware) for the ports on the interface module must match that on
the HelixNet Main Station itself.
Note: Ethernet and fiber option modules do not contain software.

Page 87
To check the software version for the Main Station and each port on the interface
module:

1) In Menu mode, select Administration > Software > Current.

2) In the fourth menu, use the rotary control to scroll the displayed
software versions.

3) The software versions for each port are listed under Snx, where n
indicates the slot number, and x indicates port A or port B.
The software versions for the two processors in the Main Station (Main
Station and IV-Router) are listed under MS and IVR respectively.

5.7 Administration
In Menu mode > Administration, you can:
 View the current versions of the software for the system.
 Update the software (firmware).
 Lock or unlock the menus on HBP-2X beltpacks, Remote Stations and
Speaker Stations connected to the Main Station.
 Reset the Main Station to the default settings.
 Manually reboot the Main Station.
 Save and Restore the settings.

Viewing the current versions of the software


To view the current versions of the software on the Main Station, see 4.6.4
Viewing the Module Settings: Version information.

Updating the software


Any HBP-2X beltpacks, Remote Stations and Speaker Stations that are connected
to the Main Station are automatically updated. The units remain non-functional for
approximately 5 minutes while they are updated.
To update the software:

1) After downloading the software update, copy the update to a USB memory
stick.

2) Insert the memory stick into the USB 2.0 (A) connector. See Table 2-3
Key to Main Station/Remote Station front panel diagram.

3) In Menu mode, select Administration and then Software.

Page 88
4) From the third menu, select Update.

5) The fourth menu displays the new software version information on the
USB memory stick. To start updating the Main Station with the new
software, press the rotary control.
The process of updating the software takes several minutes. Please wait while all
connected devices are updated. The following system messages are displayed
during the process:
Loading image
Erasing flash
Writing to flash
Verifying flash
Successful
Note: Do not remove the USB memory stick from the Main Station until the software
update is completed, including the update to any connected devices.

Do not turn off the power to the Main Station during the software
(firmware) update. Turning off the power can damage the device.

Note: The Main Station resets automatically. You are not required to restart the Main
Station. To check that the software upgrade was performed successfully, see
5.7.1 Viewing the current versions of the software.

To upgrade the License on your HelixNet Main Station


The Main Station arrives with a license for 12 Channels. In order to upgrade to 24
Channels you need to obtain a License code from your Clear-Com dealer. Your
dealer will need the system id of your device, available from the front menu
screens.

1) In Menu mode, select Administration and then License.

2) From the third menu, select Current.

3) In the fourth menu, the top item is the system ID. Give this to your dealer
to obtain a license to upgrade.

4) When you have the license code, input it into this screen. The Rotary
controller can be used to scroll to the input code section, and then used to
enter the code. Push to select a digit or letter. Scroll to the required letter.
Push to commit information.

Page 89
Resetting the Main Station to default (factory mode)
settings.
To reset the Main Station to its default (factory mode) settings:

1) In Menu mode, select Administration and then Reset.

2) The third menu displays a selected menu item: Reset to Default.

3) In the fourth menu, select between:


 Reset HMS
 Reset Devices
 Reset All
The beltpacks will receive updated (default) role information. All other local
beltpack settings will not be reset if the Main Station is reset to default settings.
Resetting a Main Station to factory settings will erase any Role configurations you
have made. Please save Role configurations before doing this.

Manually rebooting the Main Station


To manually reboot the Main Station:

1) In Menu mode, select Administration and then Reset.

2) The third menu select Reboot.

3) In the fourth menu, select Reboot Now.


When the rotary control is pressed, the display changes to Rebooting … for 2
seconds, and then the Main Station reboots.

Saving and restoring the software settings.


To save or restore the software settings:

1) Insert a memory stick into the USB 2.0 (A) connector. See Table 2-3 Key
to Main Station/Remote Station front panel diagram.

2) In Menu mode, select Administration and then Settings.

3) To save, in the third menu, select Save. Once you select Save you should
not remove the USB stick right away. Depending on the USB stick it might
take up to 5 seconds to complete.
a) In the fourth menu, select Local.

Page 90
4) To restore all HMS settings, including Networking, Linking and Expansion
settings, in the third menu, select Restore Local.
a) In the fourth menu, select a file from USB.

5) To restore all Roles and Channel names only, in the third menu, select
Restore System.
b) In the fourth menu, select a file from USB.

5.8 Diagnostics
The Diagnostics menus help you to monitor the performance of the Main Station
and diagnose possible system issues.
If the warning icon shows up in the Main display, warning message will show up
here in the Diagnostics menu.

Viewing hardware information


To view information about the hardware (PCBs) on the Main Station:

1) In Menu mode, select Diagnostics and then Hardware.

2) From the third menu, select one of the following:


 Main PCB
 Slot 1 PCB
 Slot 2 PCB
 Slot 3 PCB
Note: Slot 1, Slot 2 and Slot 3 refer to the interface module slots in the
Main Station extension bay. When looking at the rear of the
module, slot 1 is the left-hand slot, slot 2 is the middle slot, and
slot 3 is the right-hand slot.
The fourth menu displays the Part number, Revision and Serial
numbers for the PCB. The format is similar to the following:
Part xxxxxx
Revision: x
Serial: x
Where x is a numerical value.

Viewing temperature information


To view the temperature of the Main Station:

1) In Menu mode, select Diagnostics and then Hardware.

Page 91
2) From the third menu, select one of the following temperature sensors:
 Sensor 1
 Sensor 2
 Sensor 3
The fourth menu displays the temperature, for example:
+30°C
Environmental note:
The recommended operating temperature range for the HelixNet
HMS-4X Main Station is 0 to +40°C. The storage temperature range for
the Main Station is -30 to +70°C.
For more environmental information, see 3 Installing HelixNet
Partyline.

Viewing powerline information and status


There are two digital partylines (Line 1 and Line 2) on the HMS-4X Main Station.
Line 1 and Line 2 are also referred to as powerlines.
Each line can support up to 10 HBP-2X beltpacks, Remote Stations or Speaker
Stations.
Note: See also F G and I
in Table 2-3 Key to Main Station/Remote Station front
panel diagram.

To view line information and status:

1) In Menu mode, select Diagnostics and then Powerlines.

2) From the third menu, select one of the following:


 Powerline 1 (refers to Line 1)
 Powerline 2 (refers to Line 2)

3) The fourth menu displays the status and other measures / information for
the powerline. The status of the powerline is either Ok [operating
normally], Busy or Error.
For more details of the information displayed, see 21 Menu maps.
Note: Powerline status is also indicated by the powerline LEDS on the
front panel.
Green LED = OK
Amber LED = Busy
Red LED = Error

Page 92
For more information about powerline diagnostics, see 24 Troubleshooting.

Viewing keysets information


To view information about the keysets:

1) In Menu mode, select Diagnostics and then Keysets.

2) From the third menu (third display screen), select a keyset from 1 to 4.

3) The fourth menu (fourth display screen) displays the following status
information:
 Name – The channel name
 Talkers – The number of talkers on the partyline
 Main Stations – The number of Main Stations listening
 Beltpacks – The number of beltpacks listening on the
partyline
 Remote – The number of Remote Stations listening
 Speaker – The number of Speaker Stations listening.
 2-Wire – The number of 2-wire ports listening
 4-Wire – The number of 4-wire ports listening

5.9 Setting up a key Expansion Group

HelixNet 3.0 units can be Expanded and stacked in order to allow for visual
monitoring and easy control of multiple channels. Up to three devices (HMS-4X,
HRM-4X) can be stacked in an Expansion Group, allowing for convenient
observation and control of up to 12 Keysets. This gets rid of the need for multiple
key presses and microphones. When using this type of connectivity, the Expanded
panels act as slaves to the Host panel.

Page 93
Figure 5-1 A key Expansion Group
To set up an Expansion Group, once the devices have been connected to the
same LAN by Ethernet cable, you will need to identify a Host device. This is done
from the front panel menu of the device under Station Settings. Then designate
the panel(s) to be stacked as Expansion Panel(s).
Once this set up is established, you will be able to control all Channels from the
Host panel.
 Volume and buttons are synched.
 Unused buttons on Expanded panel are disabled: HSet, Mic On, SA, All
Talk, OPT, Main, PGM.
Restrictions:
 Devices can only connect as an Expansion Group over LAN, not when
connected over digital partyline.
 HMS-4X or HRM-4X can act as Host Panel.
 HMS-4X can only act as a key Expansion Panel to another HMS-4X.
 HRM-4X can act as a Key Panel to an HMS-4X and an HRM-4X.
 If an HRM-4X is already Paired to an HMS-4X it will only see Host Panels
that are part of the same group.
 If an HRM-4X is not Paired yet to an HMS-4X it will see all Host Panels in
the subnet and will automatically Pair at the same time a Host Panel is
selected.
 An Expansion Group must be set up from the device menus, and cannot
be set up from the CCM.

To set up a key Expansion Group (example set-up)


Designate the expansion Host unit:

Page 94
1) On the device, press the MENU button to enter menu mode.
Note: For each menu, turn the rotary control clockwise to scroll down
the menu items. Turn counter clockwise to scroll up the menu
items.
Off-screen menu items are indicated by arrows at the top and/or
bottom of the screen.
Selected menu items (which create your path through the four
menus) are highlighted in solid yellow.
The current setting is indicated by a dotted box around the menu
item
When you have selected a setting by rotating the right hand rotary
control, press that rotary control to enable the setting on the
Main Station.

2) Navigate to Menu > Networking > Expansion Mode. Select Host.

3) From the 4th screen on the device select Enabled. The device will then be
open for expansion.

Enable expansion on Host device


Note: On both Host and Expansion panels a “stacking” icon will flash
until connection is established.

Stacking icon

Designate the Expansion panel and link it to the host:

4) From the front panel menus of the panel you wish to expand from the
host, navigate to Menu > Networking > Expansion Mode > Host

Page 95
5) Select the required host panel using the rotary controllers, which,
providing the devices are on the same network, will be visible in the 4th
screen.

6) The stacking icon will flash in the screen until connection is established.
Once the connection is established, the icon will show solid.

Select Host from Expansion Panel

Page 96
6 Configuring and managing the Remote
Station from device menus
This chapter describes how to configure the settings and manage the Remote
Station using Menu mode. It also shows you how to monitor and diagnose
performance issues, using the Diagnostics menus.
Tip: For a quick reference to the Remote Station menus, see 21 Menu maps.
For general information about using the menus and configuring settings, see 5.1
Using the Menus.
Note: Some of the configuration information for the Remote Station is the same as for
the Main Station. In these case, you are referred to the relevant sections of
chapter 5.
Note: If Menu mode is locked, you must unlock the menus from CCM before you can
enter the menu. See section 6.

6.1 Configuring the audio settings


Audio settings for the headset
To configure the audio settings for the headset, see 5.2.1 Audio settings for
the headset.
Note: This does not apply to the Remote Station in expansion mode.

Audio settings for the microphone


To configure the audio settings for the microphone, see 5.2.2 Audio settings for
the microphone.
Note: This does not apply to the Remote Station in expansion panel mode.

Settings for program/audio in


To configure the audio settings for the program/audio in:

1) In Menu mode, select Audio Settings and then PGM/Audio In.

2) To edit the label for this input:


a) From the third menu, select Label.
b) From the fourth menu, select the existing label by scrolling to it and
pushing the rotary controller. Edit the label by rotating the
controller to scroll through letters and digits and pushing to select a
letter/digit.

Page 97
c) When you have done, scroll to Save and push the rotary controller.
To exit without saving changes, go back to the third screen.

3) To select the gain:


d) From the third menu, select Gain.
e) From the fourth menu, select one of the following:
 + 12dB
 + 6dB
 0dB (default)
 - 6dB
 - 12dB
f) To confirm the selected setting, press the rotary control.

4) To select the IFB dim level:


a) From the third menu, select IFB Dim Level.
Note: The IFB Dim Level determines the volume level the Program Level
is reduced to when it is interrupted by the IFB.
b) From the fourth menu, select one of the following:
 IFB Disabled (default)
 - 6dB
 -12dB
 -18dB
 -24dB
 Full Cut
c) To confirm the selected setting, press the rotary control.

5) The GPO trigger activates a relay when receiving a call or activating a talk
on a partyline channel. You can enable or disable the GPO trigger.
a) In Menu mode, select Audio Settings and then Program Input.
b) From the third menu, select GPO Trigger.
c) From the fourth menu, select one of the following:
 Enabled (default)
 Disabled
d) To confirm the selected setting, press the rotary control.
Note: You can also configure the GPO trigger using Menu Mode >
Modules Settings.

Page 98
6) To select the VOX:
e) From the third menu, select VOX.
f) From the fourth menu, select one of the following:
 Enabled
 Disabled (default)
g) To confirm the selected setting, press the rotary control.

7) To select the VOX Off Delay:


a) From the third menu, select VOX Off Delay.
b) From the fourth menus, select one of the following:
 .5 sec (default)
 1 sec
 2 sec
 3 sec
 4 sec
c) To confirm the selected setting, press the rotary control.

Audio settings for the SA (Stage Announce) output


To configure the settings for the SA output:

1) In Menu mode, select Audio Settings and then SA/Audio out.

2) To select the mode:


a) From the third menu, select Mode.
b) From the fourth menu, select one of the following:
 Channel Assigned (default)
 SA
c) To confirm the selected setting, press the rotary control.

3) To select the gain:


a) From the third menu, select Gain.
b) From the fourth menu, select one of the following:
 +12dB
 +6dB
 0dB (default)
 -6dB
Page 99
 -12dB
c) To confirm the selected setting, press the rotary control.

4) The Program Output setting enables the program to be delivered to this


output if it is assigned to a channel that also has a program feed assigned.
To select the program output:
a) From the third menu, select Program Output.
b) From the fourth menu, select one of the following:
 Unmute (default)
 Mute
 [SA Mode]
c) To confirm the selected setting, press the rotary control.

5) To associate one of the four available channels (or to disable channels


associations) with the selected port:
a) From the third menu, select Channel Assign.
b) From the fourth menu, select one of the following:
 Disabled (default)
 Channel 1
 Channel 2
 Channel 3
 Channel 4
 …
c) To confirm the selected setting, press the rotary control.

Audio settings for Hot Mic Output


To configure the audio settings for the Hot Mic Output, see 5.2.6 Audio settings
for the Hot Mic Output.
Note: This does not apply to the Remote Station in expansion mode.

Audio settings for the Front Panel


To configure the audio settings for the Front Panel, see 5.2.7 Audio settings for
the Front Panel.
Note: This does not apply to the Remote Station in expansion panel mode.

Page 100
6.2 Selecting Station Settings
Setting Preferences
To set the Preferences:

1) In Menu mode, select Station Settings and then Preferences.

2) You will see Roles in the third screen.

3) From the fourth screen, select the required Role. Select Local config if
you do not wish to use a Role.

Setting Keyset Assignments


To configure the Keyset Assignments settings, see 5.3.2 Setting Keyset
Assignments.

Setting key latching


To configure the key latching settings, see 5.3.3 Setting key latching.

Settings the RMK (Remote Mic Kill) key


To configure the RMK settings, see 5.3.6 Setting the RMK (Remote Mic Kill)
key
Note: This does not apply to the Remote Station in expansion panel mode.

Setting display screen brightness


To configure the display screen brightness, see 5.3.7 Setting display screen
brightness

Setting key brightness


To configure the key brightness settings, see 5.3.8 Setting key brightness.

Setting the screensaver


To configure the screensaver settings, see 5.3.9 Setting the screensaver.

6.3 Configuring the channel settings


Editing the channel label
To edit the channel label, see 5.4.1 Editing the channel label.

Page 101
Assigning the Program Listen to a channel
To assign the program listen to a channel, see 5.4.2 Assigning the Program
Listen to a channel.

Assigning a GPO relay to a channel


You can assign a relay that is triggered on receiving a call or detecting a talk on a
partyline channel. See 5.4.3 Assigning a GPO relay to a channel.

Page 102
6.4 Configuring the Control I/O
The Control I/O connector on the rear panel allows you to connect one relay
output or one opto input and control them through the Remote Station keysets:
I/O type Description
Opto inputs Opto inputs enable you to connect a foot switch or
other control device and use it to trigger Call or Talk
functions.
Relay outputs Relay outputs enable you to use Call or Talk keys to
trigger any external device that accepts a standard
contact closure (such as a theater curtain or an On
Air light).
Table 6-1: Opto inputs and Relay outputs

Configuring Opto inputs


To configure the Control I/O for the Opto input:

1) In Menu mode, select Control I/O.

2) From the second menu, select Inputs.

3) From the third menu, select Opto 1

4) From the fourth menu, select one of the following:


 None (default)
 Call Key 1
 Talk Key 1
 Call Key 2
 Talk Key 2
 Call Key 3
 Talk Key 3
 Call Key 4
 Talk Key 4
Note: The number of the key relates to the keyset to which it belongs
(for example, Call Key 1 is the Call key for the first keyset /
display screen).

5) To confirm the selected setting, press the rotary control.

Page 103
Configuring the Relay output
To configure the Control I/O for the Relay output:

1) In Menu mode, select Control I/O.

2) From the second menu, select Outputs.

3) From the third menu, select Relay 1

4) From the fourth menu, select one of the following:


 None (default)
 Call Key 1
 Talk Key 1
 Call Key 2
 Talk Key 2
 Call Key 3
 Talk Key 3
 Call Key 4
 Talk Key 4
 SA Key
Note: The number of the key relates to the keyset to which it belongs
(for example, Call Key 1 is the Call key for the first keyset /
display screen).

5) To confirm the selected setting, press the rotary control.

6.5 Connecting the Remote Station to a Main Station


using LAN
To connect the Remote Station to a Main Station:

1) Ensure that the Remote Station is physically connected to the Main


Station.

2) In Menu mode, select Networking, and then Pair to Station.

3) From the third menu, select the Station ID to connect to.


To set the preferences:

1) In Menu mode, select Networking, and then Preferences.

Page 104
From the third menu, select DHCP.
a) Select one of the following:
 Enabled (default)
 Disabled

2) From the third menu, select IP Address, and enter the correct IP
address.

3) From the third menu, select Gateway, and enter the correct gateway
address.

4) From the third menu, select Subnet Mask, and enter the correct subnet
mask

6.6 Administration
In Menu mode > Administration, you can:
 View the current versions of the software for the system.
 Update the software (firmware).
 Reset the Remote Station to the default (factory mode) settings.
 Manually reboot the Remote Station.
 Save and Restore the software settings.

Viewing the current versions of the software


To view the current versions of the software on the Remote Station:

1) In Menu mode, select Administration and then Software.

2) From the third menu, select Current.

3) In the fourth menu, use the rotary control to scroll the displayed
software versions. The software versions for the HelixNet system and
Remote Station are shown.

Updating the software


Software can be updated from a Main Station or locally in the USB connector on
the front of a Remote Station. Updating from the Main Station is recommended
when possible.
To update the software:

1) After downloading the software update, copy the update to a USB memory
stick.
Page 105
2) Insert the memory stick into the USB connector.

3) In Menu mode, select Administration and then Software.

4) From the third menu, select Update.

5) The fourth menu displays the new software version information on the
USB memory stick. To start updating the Main Station with the new
software, press the rotary control.
The process of updating the software takes several minutes. The following system
messages are displayed during the process:
Loading image
Erasing flash
Writing to flash
Verifying flash
Successful

Do not turn off the power to the Remote Station during the
software (firmware) update. Turning off the power can damage the
device.

Note: Do not remove the USB memory stick from the Main Station or Remote Station
until the software update is completed.
Note: The Remote Station resets automatically. You are not required to restart the
Remote Station. To check that the software upgrade was performed successfully,
see 6.6.1 Viewing the current versions of the software.

Resetting the Remote Station to default settings.


To reset the Remote Station to its default (factory mode) settings:

1) In Menu mode, select Administration and then Reset.

2) The third menu displays a selected menu item: Reset to Default.

3) In the fourth menu, select Reset Now.

Manually rebooting the Remote Station


To manually reboot the Remote Station:

1) In Menu mode, select Administration and then Reset.

2) The third menu select Reboot.


Page 106
3) In the fourth menu, select Reboot Now.
When the rotary control is pressed, the display changes to Rebooting … for 2
seconds, and then the Remote Station reboots.

Saving and restoring the software settings.


To save or restore the software settings:

1) In Menu mode, select Administration and then Settings.

2) To save, in the third menu, select Save. Once you select Save you should
not remove the USB stick right away. Depending on the USB stick it might
take up to 5 seconds to complete.
a) In the fourth menu, select either saving to a USB stick or saving
locally.

3) To restore, in the third menu, select Restore.


a) In the fourth menu, select either restoring from a USB stick or
restoring from a list of files.

6.7 Diagnostics
The Diagnostics menus help you to monitor the performance of the Remote
Station and diagnose possible system issues.

Viewing powerline information and status


To view line information and status:

1) In Menu mode, select Diagnostics and then Powerlines.

2) From the third menu, select Powerline 1.

3) The fourth menu displays the status and other measures / information for
the powerline. The status of the powerline is either Ok [operating
normally], Busy or Error.
For more details of the information displayed, see 21 Menu maps.
Note: Powerline status is also indicated by the powerline LEDS on the
front panel.
Green LED = Ok
Amber LED = Busy
Red LED = Error
For more information about powerline diagnostics, see 24 Troubleshooting.

Page 107
Viewing network information
To view network status information:

1) In Menu mode, select Diagnostics and then Network.

2) To view status information about the powerline:


a) From the third menu, select Powerline.
b) On the fourth menu, the IP address is given.

3) To view status information about the Ethernet:


a) From the third menu, select Ethernet.
b) On the fourth menu, the IP address is given.

Viewing keyset information


To view information about the keysets:

1) In Menu mode, select Diagnostics and then Keysets.

2) From the third menu, select a keyset from 1 to 4.

3) The fourth menu displays the following status information:


 Name – The channel name
 Talkers – The number of talkers on the partyline
 Main Stations – The number of Main Stations listening
 Beltpacks – The number of beltpacks listening on the
partyline
 Remote – The number of Remote Stations listening
 Speaker – The number of Speaker Stations listening.
 2-Wire – The number of 2-wire ports listening
 4-Wire – The number of 4-wire ports listening

6.8 Setting up a key Expansion Group


See 5.9 Setting up a key Expansion Group

Page 108
7 Using the Main Station/Remote Station
This chapter describes how to use the Main Station/Remote Station, after your
HelixNet Partyline system has been installed and configured.
For more information about integrating and using HelixNet Partyline with your
existing intercom infrastructure, see 3 Installing HelixNet Partyline.
Tip: For a quick reference to the functionality of the HMS-4X Main Station, the optional
interface modules and the HBP-2X Beltpack, see 2 Panels and Interfaces.

7.1 Using the gooseneck mic, loudspeaker and


headset
To use a gooseneck mic to talk to connected intercom users, devices (including
HBP-2X beltpacks) and systems:

1) Connect the gooseneck mic, using the gooseneck mic connector (3-pin
female Tuchel connector) on the left of the front panel.
C
Note: For the location of the gooseneck mic connector, see in Table 2-3 Key to
Main Station/Remote Station front panel diagram.

2) To talk to other intercom users and devices:


a) Press the appropriate Talk key
When the mic (gooseneck or headset) is live, the Mic On key is activated
automatically.
b) Speak into the mic.
Use the front panel loudspeaker to listen to connected intercom users, devices
and the Program Feed.
To adjust the volume level:

3) Adjust the volume of all incoming audio by turning the loudspeaker rotary
control [Main], located to the left of the loudspeaker.
Adjust the volume of the Program Feed in relation to the overall volume
level by turning the auxiliary loudspeaker rotary control [Prog], located to
the right of the loudspeaker. The Prog volume control is subordinate to
the Main volume control.
To increase the volume level, turn the rotary control(s) clockwise. To
decrease the volume level, turn the rotary control(s) counter-clockwise.
Note: When you connect a headset, incoming audio is routed to the
headset instead of the loudspeaker.

Page 109
As you increase or decrease the volume, the level control LEDs pass
through a range of indicator colors:
LED color Volume level
Green Low
Amber / Green Low / Medium
Amber Medium
Red / Amber Medium / High
Red High
Table 7-1: Loudspeaker volume indicator colors
To use a headset to talk and listen to connected intercom users, devices and
systems:

1) Connect the headset, using the headset connector (4-pin XLR–M) on the
far left of the front panel.
The Headset key is automatically activated. Incoming audio is routed to
the headset instead of the loudspeaker.
Note: For the location of the headset connector and the headset key, see
B E
in Table 2-3 Key to Main Station/Remote Station front
panel diagram.
To configure audio settings for the headset, see 5.2.1 Audio settings for
the headset.

2) To talk to other intercom users and devices:


a) Press the appropriate Talk key.
When the microphone (gooseneck or headset) is live, the Mic On key is
activated automatically.
b) Speak into the microphone.

3) To adjust the volume level of incoming audio to the headset:


a) Adjust the volume of all incoming audio by turning the loudspeaker
rotary control [Main]. The control is located to the left of the
loudspeaker.
b) Adjust the volume of the Program Feed in relation to the overall
volume level by turning the auxiliary loudspeaker rotary control
[Prog. The control is located to the right of the loudspeaker.
The Prog volume control is subordinate to the Main volume control.

Page 110
Switching between the headset mic and the gooseneck
mic
When both a Headset microphone and a gooseneck microphone are connected,
press the
Headset key to activate the headset mic.
Press the Headset key again to switch to the gooseneck mic (and deactivate the
headset mic).
Tip: To find out more about Clear-Com accessories, including headsets and gooseneck
microphones, see http://www.clearcom.com/product/accessories.

7.2 Entering and exiting Menu mode


Use Menu mode to:
 Configure the settings for the Main Station, including channel and audio
settings.
 Administrate the system, monitor system performance and diagnose
system issues.
 Perform software updates.
In Menu mode, the display screens display the four levels of menu. The menu
hierarchy proceeds left to right:
 The top level menu is presented in the first screen (furthest left on the
front panel).
 The lowest level menu is presented in the fourth screen (furthest right
on the front panel).
To place the Main Station in Menu mode, press the Menu key to the left of the
first (left) display screen. To exit Menu mode, do either of the following:
 Press the Menu key again.
 Wait until Menu mode times out. If you fail to press any key on the front
panel for 20 seconds, the display screens revert to showing the standard
channel information, see Table 2-5 Main Station/Remote Station
display icons and indicators.
Tip: For more detailed information about using the Main Station menus, see 15
Linking in the Core Configuration Manager (CCM).
Main Stations can be linked from the CCM. Each Main Station has 12 Channels
with the option of licensing 12 more (24 in total). When linking Main Stations,
Channels with the same number are merged together into one Channel. Linking
Main Stations will also have the effect of increasing your I/O and device module
options (more beltpacks and a larger area covered).

Page 111
Note: Linked Main Stations should have the same amount of licensed channels. If you
link a 24 Channel device to a 12 Channel device the system will default to 12
Channels only. To buy a license for more Channels see 5.8.1 License.
Main Stations can still be linked from the device menus. See 12 Linking Main
Stations.

7.3 A HelixNet Link-Group Overview


 A HelixNet Link-Group can contain up to three Main Stations. More is
possible but not advised.
 A Link-Group must have one device designated as Link-Master.
 The Link-Group performs a “best effort” approach to creating a mesh
network between all the devices within the group.

Figure 7-1 A Link-Group

The Link-Master
The Link-Master designation serves three main purposes:

1) It facilitates Link-Group membership.

2) It is the owner of configured Role information, meaning that Roles will


only persist (be maintained consistently) if the Link-Master is operational.

Page 112
3) It is responsible for the synchronization and distribution of both
configuration (Roles) and device availability status throughout the Link-
Group.
Note: Clear-Com recommends that the IP address of the Link-Master is allocated
statically. When allocated by DHCP, the IP address can change. If this happens
the Link-Members will no longer be able to reach the Link-Master device, and Role
information may not be persisted.
Note: Any device can be set to Link-Master or Link-Member. The default setting for
HelixNet linking mode is Linking Disabled. This setting stops the device from
broadcasting its name to the network (via its mDNS index).
Note: Linked Main Stations need 2 – 5 Mbps of bandwidth.

The Link-Members
HelixNet devices that are not identified as master will have the designation of
Link-Member. Joining a device to a Link-Group requires that device to be set to
Link-Member which will prompt the user to enter the IP address of the Link-
Master.

7.4 Device configuration in the CCM


Note: Any IP connectivity requires an Ethernet or Fiber module fitted to the Main
Station.
Once the units have joined a Link-Group, the devices can be configured either
directly or by proxy. The host device is the unit which a browser is currently
directed to.
The Home button will always take you to the host device’s configuration page.
 Proxy configuration can be accomplished by clicking on any device within
the Overview page.

Page 113
Figure 7-2 Host device concept

Note: The host device will always have an orange highlight in the CCM.

7.5 Linking Main Stations in the CCM


Main Stations to be linked in the CCM must first be connected by cable as
described in Chapter 3. Installation and Chapter 12, Linking Main Stations.
In order to create a Link-Group in the CCM, you must designate one unit as Link-
Master. The other units are designated Link-Member and are joined to the Master
via the Master’s IP address. This is achieved in the Linking page of each unit.

1) From a browser, access the CCM of HelixNet Main Station #1 by typing its
IP address into the URL field.

Default login and password for the CCM: admin, admin.


Note: The unit’s IP address can be found in the device’s display screens:
Menu > Networking > Preferences > IP address.
Note: The Link-Master IP must be statically allocated to prevent loss of
service.

2) Navigate to Home > Linking in the CCM. From the drop-down box select
Link-Master and click Apply Changes. This designates this unit as Link-
Master.

Page 114
Note: The default linking mode is: Linking Disabled.

3) From a new browser window, access the CCM of device #2 by typing the
unit’s IP address into the URL field.

You will have to enter the password and login for the device (Default,
admin, admin)

4) Navigate to Home > Linking and select Link-Member from the drop down
box.

5) You will be prompted for the IP address of the Link-Master. Within the
Master IP address field, enter the IP address of device #1. Click on blue
check mark or <ENTER> key to submit.

Page 115
Either accept the default Link Group Member ID (orange highlight) or
select a new one by clicking on it. Click Apply Changes. This links this
device to the Link Master.

6) Navigate to the Overview page (top navigation bar). Both HelixNet


devices should be displayed on this page.

7) Repeat steps 3) to 6) for a third device if required.


Tip: Configuring and managing the Main Station.

7.6 Using the channel keysets


A keyset (set of controls) is located next to each of the four display screens. In
operating mode, each keyset is dedicated to the control of one of the four
supported intercom channels. For details of the standard on screen information
for each channel, see Table 2-5 Main Station/Remote Station display icons
and indicators.
Note: To change (edit) the channel label (name), see 5.4.1 Editing the channel label.
Page 116
The display screens enters screensaver mode (if enabled) if the Main Station
remains inactive for 10 minutes. Press any key to leave screensaver mode.
To send a call signal to all the connected devices on that channel, press the Call
key.
To talk to the all the devices on that channel:

1) Press the Talk key. When the gooseneck or headset mic is live, the Mic
On key is activated automatically.

2) Speak into the headset or gooseneck mic (see also 7.1 Using the
gooseneck mic, loudspeaker and headset ).
To adjust the volume of incoming audio, turn the rotary control. Turn the
rotary control clockwise to increase the volume, and counter-clockwise to
decrease volume. The current volume level is shown on screen.
To mute incoming audio, press the rotary control. The display screen displays
the muted volume bar.
To unmute incoming audio (restoring the audio to its previous volume level),
press the rotary control again.
Note: In Menu mode, the rotary control for each channel keyset is used to scroll and
select menu items. For more information, see 5.1 Using the Menus.

7.7 Using the All Talk key


To talk to all connected intercom users, devices and systems, excluding the SA
(Stage Announce) facility:

1) Press the All Talk key to the right of the fourth (last) display screen.
Talk keys for all channels are activated automatically.
When the mic (gooseneck or headset) is live, the Mic On key is also
activated automatically.

2) Speak into the headset or gooseneck mic (see also 7.1 Using the
gooseneck mic, loudspeaker and headset ).
Note: All Channels will enable you to talk to 12 (or 24, according to license) Channels.
Visible Channels will enable you to talk to the four Channels visible in the menu
screens of your device.

7.8 Using the SA [Stage Announce] key


Use the SA [Stage Announce] key to speak to an attached SA or Public Address
system (sometimes simply a loudspeaker within the studio, theater or event
area).To make a studio / public announcement:

Page 117
1) Press the SA key to the right of the fourth (last) display screen.
When the mic (gooseneck or headset) is live, the Mic On key is also
activated automatically.

2) Speak into the headset or gooseneck mic (see also 7.1 Using the
gooseneck mic, loudspeaker and headset ).

7.9 Using the RMK [Remote Mic Kill] key


Note: The RMK key is only present on the HelixNet Main Station. The Remote Station
has instead an OPT key which is non-functional.
Use the RMK [Remote Mic Kill] key to:
 Send a message to all connected HelixNet Partyline devices to deselect
any latched (active) Talk keys.
 Turn off any latched Talk keys on connected analog partyline beltpacks
and stations.
Note: All Channels will turn off Talk keys on 12 (or 24 according to license) Channels.
Visible Channels will turn of Talk keys on the four Channels you can see on the
front of the device.
Note: The OPT key can be used in HelixNet 3.0 and above. The Remote Station must
have a Role selected to use this function. To enable the key, navigate to the
Roles page in the CCM, the browser-based configuration tool served by your
device.
To enable the OPT (RMK) key on a Remote Station:

1) Input the IP address of your device into the URL field on a browser. The IP
address is found in the 4th screen on the front of your device: MENU >
Networking > Preferences > IP address.

Default Username and Password for the CCM: admin, admin.

2) This takes you to the Overview page in the Core Configuration Manager
(CCM). Navigate to Roles > Remote Station > Role > Station > OPT
(RMK) Key in the CCM and select the option by clicking on it.

Page 118
3) Select required option: All Channels to activate RMK on 12 or 24
Channels, Visible Channels to activate RMK on the Channels visible on
your device only, or Disabled (default setting).
Enabling this option in the CCM takes effect immediately on your system,
provided the Role is selected on your device. For more information on Roles see
12 Roles.

7.10 Line 1 and 2 LEDs


Note: This section only applies to the HelixNet Main Station.
The HBP-2X beltpacks, Remote Stations and Speaker Stations are connected by
one of the two lines to the Main Station.
The color of the Line 1 and Line 2 LEDs to the left of the front panel
loudspeaker indicate the service status of each powerline:
 Green LED = Ok.
 Amber LED = Busy.
 Red LED = Error.
For more information:

Page 119
 About the service status of Lines 1 and 2, see 5.8.3 Viewing powerline
information and status.
 About monitoring system performance and diagnosing system issues on
the Main Station, see 5.8 Diagnostics.

7.11 Line and LAN LEDs


Note: This section only applies to the HelixNet Remote Station and Speaker Station.
The Remote Station has a line LED that indicates the status of a powerline
connection to the Main Station. The LAN LED indicates the status of the Ethernet
connection, if present.
The color of the Line and LAN LEDs to the left of the front panel loudspeaker
indicate the service status of each powerline:
 Green LED = Ok.
 Amber LED = Busy.
 Red LED = Error.

Page 120
8 Configuring and managing the Speaker
Station from device menus
This chapter describes how to configure the settings and manage the Speaker
Station using Menu mode. It also shows you how to monitor and diagnose
performance issues, using the Diagnostics menus.
Tip: For a quick reference to the Speaker Station menus, see 21 Menu maps.
For general information about using the menus and configuring settings, see 5.1
Using the Menus.
There is a next and a back activated by pressing the rotary encoders (right one
for next, left one for back). There are two levels of the menu, one on the left
screen and one on the right. Next and back shifts the menu by one level down or
up.

8.1 Using the Menus


To place the Speaker Station in Menu mode, press the Menu key. The Speaker
Station menus appear in the display screens.
Note: The Speaker Station menu comes up in the Roles menu by default.
Note: If Menu mode is locked, you must unlock the menus from CCM before you can
enter the menu. See section 6.

Configuring settings
To configure settings:

1) For each menu, turn the rotary control to scroll the menu items. Turn
the rotary control:
 Counter-clockwise to scroll up the menu items.
 Clockwise to scroll down the menu items.
To return to the previous level of menu, press the left-hand rotary key.
To go to the next level of menu, press the right-hand rotary key.
Selected menu items are highlighted in solid yellow.

2) When you have selected a setting, press the right-hand rotary key to
enable the setting on the Speaker Station.

Exiting Menu mode


To exit Menu mode do either of the following:
 Press the Menu key.

Page 121
 Wait until Menu mode times out. If you fail to press any key on the
Speaker Station for 20 seconds, the display screen reverts to showing
the standard channel information.

8.2 Configuring the Audio settings


Audio settings for the headset
To configure the audio settings for the headset, see 5.2.1 Audio settings for
the headset.

Audio settings for the microphone


To configure the audio settings for the microphone, see 5.2.2 Audio settings for
the microphone.

Audio settings for the Front Panel


To configure the audio settings for the front panel, see 5.2.7 Audio settings for
the Front Panel.

8.3 Station Settings


Setting Keyset Assignments
To configure the Keyset Assignments settings, see 5.3.2 Setting Keyset
Assignments.

Setting key latching


To configure key latching, see 5.3.3 Setting key latching.
You can also configure key latching so that the Talk keys automatically unlatch
whenever the Shift key is pressed. To do so:

1) In Menu mode, select Station Settings and then Keysets.

2) From the third menu, select Unlatch on Shift.

3) From the fourth menu select:


 Enabled (default)
 Disabled

Setting display screen brightness


To configure display screen brightness, see 5.3.7 Setting display screen
brightness.

Page 122
Setting key brightness
To configure key brightness, see 5.3.8 Setting key brightness.

Setting the screensaver


To configure the screensaver, see 5.3.9 Setting the screensaver.

8.4 Connecting the Speaker Station to a Main Station


To connect the Speaker Station to a Main Station, see 6.5 Connecting the
Remote Station to a Main Station using .

8.5 Module Settings


See 5.6 Configuring Module Settings

8.6 Administration
Viewing the current versions of the software
To view the current version of the software, see 6.6.1 Viewing the current
versions of the software.

Updating the software


To update the software, see 6.6.2 Updating the software.
Note: You can only update the Speaker Station software from the Main Station.

Resetting the Speaker Station to default (factory mode)


settings.
To reset the Speaker Station to its default (factory mode) settings see:

1) In Menu mode, select Administration and then Reset.

2) The third menu displays a selected menu item: Reset to Default.

3) In the fourth menu, select Reset Now.

Manually rebooting the Speaker Station


To manually reboot the Speaker Station:

1) In Menu mode, select Administration and then Reset.

2) The third menu select Reboot.

Page 123
3) In the fourth menu, select Reboot Now.
When the rotary control is pressed, the display changes to Rebooting … for 2
seconds, and then the Speaker Station reboots.

8.7 Diagnostics
Viewing powerline information and status
To view powerline information and status, see 6.7.1 Viewing powerline
information and status.

Viewing network information


To view network information, see 6.7.2 Viewing network information.

Viewing keysets information


To view key sets information, see 6.7.3 Viewing keyset information.

Page 124
9 Using the Speaker Station
This chapter describes how to use the Speaker Station, after your HelixNet
Partyline system has been installed and configured.
For more information about integrating and using HelixNet Partyline with your
existing intercom infrastructure, see 3 Installing HelixNet Partyline.

9.1 Using the gooseneck mic, loudspeaker and


headset
To use a gooseneck mic to talk to connected intercom users, devices (including
HBP-2X beltpacks) and systems:

1) Connect the gooseneck mic, using the gooseneck mic connector (3-pin
female Tuchel connector) on the left of the front panel.
Note: For the location of the gooseneck mic connector, see Table 2-24 Key to
Speaker Station front panel

2) To talk to other intercom users and devices:


a) Press the Talk key.
When the mic (gooseneck or headset) is live, the Mic key is activated
automatically.
b) Speak into the microphone.
Use the front panel loudspeaker to listen to connected intercom users, devices
and the Program Feed.
To adjust the volume level:

3) Adjust the volume of all incoming audio by turning the loudspeaker rotary
control [Main], located in the center of the panel.
To increase the volume level, turn the rotary control(s) clockwise. To
decrease the volume level, turn the rotary control(s) counter-clockwise.
Note: When you connect a headset, incoming audio is routed to the
headset instead of the loudspeaker.
As you increase or decrease the volume, the level control LED passes
through a range of indicator colors:

Page 125
LED color Volume level
Green Low
Amber / Green Low / Medium
Amber Medium
Red / Amber Medium / High
Red High
Table 9-1: Loudspeaker volume indicator colors
To use a headset to talk and listen to connected intercom users, devices and
systems:

4) Connect the headset, using the headset connector (4-pin XLR–M) on the
far left of the front panel.
The Headset key is automatically activated. Incoming audio is routed to
the headset instead of the loudspeaker.
Note: For the location of the headset connector and the headset key, see
Table 2-24 Key to Speaker Station front panel Table 2-3 Key
to Main Station/Remote Station front panel diagram.
To configure audio settings for the headset, see 8.2.1 Audio settings for
the headset

5) To talk to other intercom users and devices:


a) Press the appropriate Talk key.
When the microphone (gooseneck or headset) is live, the Mic key is
activated automatically.
b) Speak into the microphone.

6) To adjust the volume level of incoming audio to the headset:


a) Adjust the volume of all incoming audio by turning the loudspeaker
rotary control [Main]. The control is located to the left of the
loudspeaker.
b) Adjust the volume of the Program Feed using the PGM rotary
control.

Switching between the headset mic and the gooseneck


mic
When both a Headset microphone and a gooseneck microphone are connected,
press the Headset key to activate the headset microphone, and press the Mic
key to activate the microphone.

Page 126
Tip: To find out more about Clear-Com accessories, including headsets and gooseneck
microphones, see http://www.clearcom.com/product/accessories.

9.2 Entering and exiting Menu mode


Use Menu mode to:
 Configure the settings for the Speaker Station, including channel and
audio settings.
 Administrate the system, monitor system performance and diagnose
system issues.
In Menu mode, the display screens display the four levels of menu. The menu
hierarchy proceeds left to right:
 The top level menu is presented in the first screen (left on the front
panel).
 The second level menu is presented in the second screen (right on the
front panel).
To place the Speaker Station in Menu mode, press the Menu key to the left of
the first (left) display screen. To exit Menu mode, do either of the following:
 Press the Menu key again.
 Wait until Menu mode times out. If you fail to press any key on the front
panel for 20 seconds, the display screens revert to showing the standard
channel information:
 Channel label (name).
 Listen (volume) level.
Tip: For more detailed information about using the Main Station menus, see 5
Configuring and managing the Main Station from device menus.
This chapter describes how to use the Main Station/Remote Station, after your
HelixNet Partyline system has been installed and configured.
For more information about integrating and using HelixNet Partyline with your
existing intercom infrastructure, see 3 Installing HelixNet Partyline.
Tip: For a quick reference to the functionality of the HMS-4X Main Station, the optional
interface modules and the HBP-2X Beltpack, see 2 Panels and Interfaces.

9.3 Using the channel keysets


A keyset (set of controls) is located next to each of the four display screens. In
operating mode, each keyset is dedicated to the control of one of the four
supported intercom channels. For details of the standard on screen information
for each channel, see Table 2-5 Main Station/Remote Station display icons
and indicators.
Note: To change (edit) the channel label (name), see 3.4.1 Editing the channel label.
Page 127
The display screens enters screensaver mode (if enabled) if the Main Station
remains inactive for 10 minutes. Press any key to leave screensaver mode.
To send a call signal to all the connected devices on that channel, press the Call
key.
To talk to the all the devices on that channel:

1) Press the Talk key. When the gooseneck or headset mic is live, the Mic
On key is activated automatically.

2) Speak into the headset or gooseneck mic (see also 5.1 Using the
gooseneck mic, loudspeaker and headset ).
To adjust the volume of incoming audio, turn the rotary control. Turn the
rotary control clockwise to increase the volume, and counter-clockwise to
decrease volume. The current volume level is shown on screen.
To mute incoming audio, press the rotary control. The display screen displays
the muted volume bar.
To unmute incoming audio (restoring the audio to its previous volume level),
press the rotary control again.
Note: In Menu mode, the rotary control for each channel keyset is used to scroll and
select menu items. For more information, see 3.1 Using the Menus.

9.4 Line and LAN LEDs


The Speaker Station has a line LED that indicates the status of a powerline
connection to the Main Station. The LAN LED indicates the status of the Ethernet
connection, if present.
The color of the Line and LAN LEDs to the left of the front panel loudspeaker
indicate the service status of each powerline:
 Green LED = Ok.
 Amber LED = Busy.
 Red LED = Error.

Page 128
10 Configuring and managing the HBP-2X
Beltpack from device menus
This chapter describes how to configure the settings and manage the HBP-2X
Beltpack using Menu mode. It also shows you how to monitor and diagnose
performance issues, using the Diagnostics menus.
Tip: For a quick reference to the Main Station menus, see 21 Menu maps.

10.1 Using the Menus


To place the beltpack in Menu mode, press the Menu key on the top of the
beltpack.
Note: The Beltpack menu shows the Roles menu by default.
Note: If Menu mode is locked on the beltpack, you must unlock the menus from CCM
before you can enter the menu. See section 6.
To enter the menu mode from the Roles screen, press the left hand Call button.

Configuring settings
To configure settings:

1) For each menu, turn either of the side-mounted rotary controls to scroll
the menu items. Turn the rotary control:
 Counter-clockwise to scroll up the menu items.
 Clockwise to scroll down the menu items.
Off-screen menu items are indicated with arrows at the top and / or
bottom of the display screen.
Back (with an arrow pointing left) indicates a previous level of menu.
To return to the previous level of menu, press the left-hand Call key.
An arrow pointing right indicates another level of menu under that menu
item.
To go to the next level of menu, press the right-hand Call key.
Selected menu items are highlighted in solid yellow.

2) The final level of menu (the second or third display screen) displays the
settings that relate to your previous menu choices (system features or
functionality).
The current setting is indicated by a dotted box around the menu item

Page 129
When you have selected a setting, press the right-hand Call key to
enable the setting on the Main Station.

Exiting Menu mode


To exit Menu mode on the beltpack, do either of the following:
 Press the Menu key.
 Wait until Menu mode times out. If you fail to press any key on the
beltpack for 20 seconds, the display screen reverts to showing the
standard channel information.

10.2 Configuring the Role settings


To configure the Role settings for the headset

1) In Menu mode press the left-hand Call Key and then select Roles.

2) Select the required Role.

3) To confirm the selected setting, press the right-hand Call key.

4) The beltpack applies the setting and reverts to the standard display
screen.

Viewing Hostname
The hostname (the unique name given to any device on a network) of your
beltpack can be seen in the Roles section of the menu.
To view the hostname for your beltpack:

1) In Menu mode press the left-hand Call Key and then select Roles.

2) The device’s hostname can be seen at the top of the list of available Roles.
Note: You cannot change the hostname from this screen. The hostname for beltpacks
must be change from the web based Core configuration Manager (the CCM). From
the Overview page of the CCM, click on any device image to access configuration
details for that device’s hostname.

10.3 Configuring the Audio settings


To configure the audio settings for the headset:

1) In Menu mode press the left-hand Call Key and then select Audio
Settings.

2) To adjust sidetone gain on the headset:

Page 130
a) Select Sidetone Gain.
b) Select one of the following:
 0dB
 - 6dB
 -12dB (default)
 -18dB
c) To confirm the selected setting, press the right-hand Call key.
Go back to the previous menu level by pressing the left-hand Call key.

3) To limit the maximum audio level that can be delivered to the


headphones:
a) Select Headphone Limit.
b) Select one of the following:
 Off
 +6dB
 0dB (default)
 - 6dB
c) To confirm the selected setting, press the right-hand Call key.
Note: When Headphone Limit is set to anything except Off, a LIM
indication will show up at the top right of the display
Go back to the previous menu level by pressing the left-hand Call key.

4) Sidetone tracking means that the sidetone level varies according to the
main volume level. To set (or disable) sidetone tracking on the headset:
a) Select Sidetone Control.
b) Select one of the following:
 Tracking (default)
 Non-Tracking
 Disabled
c) To confirm the selected setting, press the right-hand Call key.
Go back to the previous menu level by pressing the left-hand Call key.

Page 131
5) To set the type of mic on the headset:
a) Select HS Mic Type.
b) Select either of the following types of mic.
 Electret (-15 dB)
 Dynamic (0 dB) (default)
 Dynamic (-10 dB)
Note: In electret mode, phantom power is provided for an electret mic.
In dynamic mode, no phantom power is provided. Mic input levels
are also adjusted between the different modes to suit the different
mic types.
c) To confirm the selected setting, press the right-hand Call key.

10.4 Audio settings for the microphone


To configure the audio settings for the microphone:

1) In Menu mode, select Audio Settings and then Microphone.

2) To select the Headroom:


a) From the third menu, select Headroom.
b) From the fourth menu, select one of the following:
 Normal (default)
 High

3) To enable or disable the Contour Filter:


a) From the third menu, select Contour Filter
b) From the fourth menu, select one of the following:
 Enabled (default)
 Disabled

10.5 Configuring the Beltpack Settings


In Menu mode > Beltpack Settings, you can:
 Assign channels to the left and right beltpack keysets (set of controls).
 Enable (or disable) Talk key latching.
 Enable (or disable) beltpack vibration when a call signal is received.
 Enable (or disable) the USB flasher mode for the beltpack.

Page 132
Tip: For a quick reference to the keysets on the HBP-2X Beltpack, see 2.5.1 HBP-2X
user controls (front and side view).

Assigning channels
You can assign any two available channels to the beltpack (including the same
channel to both keysets).
To assign a channel:

1) In Beltpack Settings select Left Channel or Right Channel.

2) Select one of the available channels (or none):

3) To confirm the selected setting, press the right-hand Call key.

Setting Talk key latching


To enable (or disable) Talk key latching:

1) In Beltpack Settings select Right Talk Latch or Left Talk Latch

2) Select one of the following:


 Latching (default)
 Non-Latching
 Disabled
Note: The setting applies to both channels on the beltpack.

3) To confirm the selected setting, press the right-hand Call key.

Setting USB Flasher mode


To enable (or disable) USB Flasher mode

1) In Beltpack Settings select either Left Keyset or Right Keyset

2) Select USB Flasher

3) Select one of the following:


 Disabled (default)
 Blinking
 Solid

4) To confirm the selected setting, press the right-hand Call key.

Page 133
Setting the beltpack to vibrate when called
To enable (or disable) vibration when a Call signal is received:

1) In Beltpack Settings select Vibrate on Call.

2) Select one of the following:


 On
 Off (default)

3) To confirm the selected setting, press the right-hand Call key.

10.6 Configuring the Display Settings


In Menu mode > Display Settings, you can:
 Set the brightness of the display screen.
 Set the brightness of the Talk and Call keys.
 Enable (or disable) the screensaver.
 Rotate the display.

Setting display screen brightness


By default, the display screen is set to medium brightness. To set the brightness
of the display screen:

1) In Menu mode, press the left-hand Call Key and then select Display
Settings.

2) Select OLED Brightness.

3) Select one of the following:


 High
 Medium (default)
 Low

4) To confirm the selected setting, press the right-hand Call key.

Setting the brightness of the Talk and Call keys


By default, the Talk and Call keys are lit when active (on) and dim when
inactive (off) (High / Low).
To set the brightness of the Talk and Call keys:

Page 134
1) In Menu mode, press the left-hand Call Key and then select Display
Settings.

2) Select Key Brightness.

3) Select one of the following brightness settings:


Key(s) Description
High / Low Keys are brightly lit when active (on) and dim when inactive
(default) (off).
High / Off Keys are lit when active (on) and are unlit when inactive (off).
Low / Off Keys are lit dim when active (on) and are unlit when inactive
(off).
Off / Off Keys are unlit, whether or not they are active (on) or inactive
(off).
Table 10-1: Setting the brightness of the Talk, Call and Menu keys

4) To confirm the selected setting, press the right-hand Call key.

Set Rotate Display


You can set the beltpack display to rotate according to its physical position.

1) In Menu mode, press the left-hand Call Key and then select Display
Settings.

2) Select Rotate Display.

3) Select one of the following:


 Enabled
 Disabled (default)

Setting the screensaver


The screensaver is displayed on screen after 10 minutes of inactivity on the
beltpack. To enable (or disable) the screensaver:

1) In Menu mode, press the left-hand Call Key and then select Display
Settings.

2) Select Screensaver.

3) Select one of the following:


 Channel Name (default)

Page 135
 Hostname
 Role Name
 Blank
 Disabled

4) To confirm the selected setting, press the right-hand Call key.

10.7 Administration
In Menu mode > Administration, you can:
 View the IP address for the network.
 View the current version of the software on the beltpack.
 Reset the beltpack to default (factory mode) settings.
The beltpacks receive updated (default) channel label information. Other local
beltpack settings will not be reset if the Main Station is reset to default settings.

Viewing the IP address


To view the IP address for the network:

1) In Menu mode, press the left-hand Call Key and then select
Administration.

2) Select Network.

3) The IP address for the network is displayed. The IP address appears


similar to the following example:
10.0.0.1
To view the current version of the software on the beltpack:

1) In Menu mode, press the left-hand Call Key and then select
Administration.

2) Select Software Version.

3) The current version of the software is displayed. The software version


information will appear similar to the following example:
npl-x.x.xx.xxxx, uboot
Where x is a numerical value.

Resetting the beltpack to default (factory mode) settings


To reset the beltpack to default (factory mode) settings:

Page 136
1) In Menu mode, press the left-hand Call Key and then select
Administration.

2) Select Reset to Default.

3) Reset Now is displayed (shown as selected). To reset the beltpack, press


the right-hand Call key.

10.8 Diagnostics
The Diagnostics menus help you to monitor the performance of the beltpack and
diagnose possible system issues.

Viewing information about the hardware (main PCB) on


the beltpack
To view information about the Part, Revision and Serial number of the main
PCB on the beltpack:

1) In Menu mode, press the left-hand Call Key and then select
Diagnostics.

2) Select Hardware > Main PCB.


The Part, Revision and Serial number for the PCB are displayed. The
format is similar to the following:
Part xxxxxxx
Revision: x
Serial: x
Where x is a numerical value.

Viewing powerline information and status


To view powerline information and status:

1) In Menu mode, press the left-hand Call Key and then select
Diagnostics.

2) Select Powerline.
The status and other powerline information are displayed. For more
information, see 21 Menu maps.

Page 137
11 Using the HBP-2X Beltpack
This chapter describes how to use the HBP-2X Beltpack, after your HelixNet
Partyline system has been installed and configured.
For more information about integrating and using HelixNet Partyline with your
existing intercom infrastructure, see 18 Connecting to Other Intercom
Systems.
Tip: For a quick reference to the functionality of the HBP-2X Beltpack, the HMS-4X
Main Station, and the optional interface modules, see 2 Panels and Interfaces.

11.1 Using the beltpack keysets


The HBP-2X Beltpack supports two Partyline channels, with a separate keyset (set
of controls) dedicated to the control of each channel:
 The left-hand keyset controls the first (top) channel displayed on
screen.
 The right-hand keyset controls the second (bottom) channel displayed
on screen.
For details of the standard on screen information for each channel, see Table 2-5
Main Station/Remote Station display icons and indicators.
Note: For more information about:
 Using the beltpack in Menu mode, see 10 Configuring and managing
the HBP-2X Beltpack.
 Changing (editing) the channel label (name), see 5.4.1 Editing the
channel label.
The display screens enters screensaver mode (if enabled) if the beltpack remains
inactive for a period of time. Press any key to exit screensaver mode.
To send a call signal to all the connected devices (beltpacks and Main Station)
on that channel, press the Call key.
To talk to all the devices connected to the channel:

1) Connect a headset, using the 4-pin XLR–M connector on the base / rear of
the beltpack.
Note: For the location of the headset connector and the headset
key, see E in Table 2-34: Key to HBP-2X Beltpack
connectors and controls (base view).

2) Press the Talk key.

3) Speak into the headset mic.

Page 138
To adjust the volume of incoming audio for a channel, turn the appropriate side-
mounted rotary control.
Turn the rotary control clockwise to increase the volume, and counter-clockwise
to decrease volume. The current volume level for the channel is shown on screen.

11.2 Entering and exiting Menu mode


Use Menu mode to:
 Configure the settings for the Main Station, including channel and audio
settings.
 Monitor beltpack performance and diagnose issues.
To enter Menu mode, press the Menu key. To exit Menu mode, press the Menu
key again.
For more information about using Menu mode on the beltpack, see 10
Configuring and managing the HBP-2X Beltpack.

11.3 Adjusting the Program Feed volume level.


To adjust the listen level (volume) of the Program Feed to the beltpack, turn the
rear / base rotary control.
Turn upwards to increase the listen level (volume), and downwards to decrease
the listen level (volume).
While the listen level is adjusted, the listen level for the Program Feed replaces
the standard channel information on screen.
The Main Station is used to assign the Program Feed to channels. For more
information, see
5.4.2 Assigning the Program Listen to a channel.

Page 139
12 Roles

12.1 Roles overview


A Role is a pre-set configuration that includes Channel assignment, audio settings,
IFBs, relays etc. Each HelixNet device has a default Role that can be used as it is
or modified to fit requirements. Each Role can be given a name (a label) that
corresponds to a common user workflow, such as producer, director, A1, etc.
When adding new Roles, you will modify an existing template, using either the
default Role for that device, or another Role that you have already made. Default
Roles can be modified but not deleted or loaded to devices, you will always work
with a copy. Default Roles can be returned to factory settings if required.
To use Roles you must have HelixNet 3.0 or above installed on your Main
Stations.
Roles are created and edited in the Core Configuration Manager (CCM) and are a
feature of HelixNet 3.0 and above. Once created in the Roles page, a Role will be
available for selection from any device which is connected to your HelixNet
system. Roles can be configured for:
 Main Stations
 Remote Stations
 Speaker Stations
 Beltpacks.
Roles can be created, cloned, edited and deleted in the Roles page.
Each device has a set of configuration options relevant to that unit. Configurable
details include keysets, audio settings, program feeds and relays.
Note: A Role can be selected by many devices.
Roles can be created in the CCM at any time, but to use the Roles, devices must
be connected to your system (for more information, see 16 Linking Main Stations
and 17 Linking Remote Stations and Speaker Stations).
To create and use Roles

1) Open the CCM by typing the Main Station’s IP into the URL field of a
browser (Default username and password: admin, admin).

2) Go to the Roles page in the CCM by clicking on the Roles button in the
top navigation bar.

3) Add or clone a Role or Roles.

4) Configure Role parameters (you can use editable default settings).


Page 140
5) Select a Role from the device panel menus and load that Role to the
device.
Once a role has been selected on a device, this role will persist over power cycles
until a new role is selected or the device is returned to factory settings.
Each device has the ability to operate a configuration local to that device (local
config), or a selected role that can be pre-configured in the CCM.
If a Role is edited in the device menus rather than the CCM, these changes will be
reflected in the CCM. The latest configuration change, whether this is made in the
CCM or from the device will dominate, neither interface has precedence.

Roles contain Roles do NOT contain


Audio settings Network settings (IP address, DHCP etc.)

Keyset Assignment Pairing information (HKB and HRM over IP)

Station settings Linking information (Link Master/Link Member)

2W/4W module assignment Expansion information (Host/Expanded panel)

Program feed assignment

GPIO configuration

12.2 Example Roles set up


The following tables give an example of how roles could be set up in a working
scenario.
Device type Device hostname Roles available Role selected by
for selection device
Main Station main_station_1 Local config Director 1

Director 1

Director 2

Sound booth

main_station_2 Local config Sound booth

Director 1

Director 2

Page 141
Sound booth

Device type Device hostname Roles available Role selected by


for selection device
Remote Station remote_station_1 Local config Green room

Green room

Device type Device hostname Roles available Role selected by


for selection device
Speaker Station speaker_station_1 Local config Local config

None configured

Device type Device hostname Roles available Role selected by


for selection device
Belt pack HBP-2X xxxxxxxxx Local config Lighting 1

Lighting 1

Lighting 2

Sound 1

Sound 2

HBP-2X xxxxxxxxx Local config Sound 1

Lighting 1

Lighting 2

Sound 1

Sound 2

Page 142
Figure 12-1 Example of Roles use in the Assignments page of the CCM
Note: A Role can be selected by many devices.

Page 143
For more detail on setting up Roles see 14 Using the CCM to configure Role.
Note: Program input feeds are an exception in this screen, they will always be associated with a device rather than a Role.

Page 144
12.3 Device default Roles
Each device type has a default configuration which can be edited and/or cloned,
but not deleted. When creating new Roles you will always use an existing Role as
a template. The default Role is editable, so you can create Roles based on a
default Role edited to reflect your system requirements.
If you edit the default Role of any device, this configuration will persist until the
device is returned to factory settings in the General > Maintenance page of the
CCM.

12.4 To select a Role for a device


Select a role for a device from the display panels on that device. Go to Menu >
Station Settings > Preferences > Roles to select a role.

1) On the device, press the MENU button to enter menu mode.

2) For each menu, turn the rotary control clockwise to scroll down the
menu items. Turn counter clockwise to scroll up the menu items.
Off-screen menu items are indicated by arrows at the top and/or bottom
of the screen.
Selected menu items (which create your path through the four menus)
are highlighted in solid yellow.
The current setting is indicated by a dotted box around the menu item

3) When you have selected a setting by rotating the right hand rotary
control, press that rotary control to enable the setting on the Main
Station.

Beltpacks will display a Role selection screen when first powered up. Simply select
the required Role.
For more information, see 5.1 Using the Menus.

12.5 Creating and editing Roles in the CCM


 Use the ADD button to create a new role with a new label based on a
default template. This is the easiest way to create roles quickly with
different labels, for example Camera, Sound, Production and so on.
 Use the CLONE button to copy an existing Role. This is the easiest way
to create copies of Roles with the same label (appended by one), for
example Camera!, Camera2, Camera3 and so on.

Page 145
Figure 12-2 The Roles page in the CCM

1) Navigate to the Roles page in the CCM. When creating Roles you will
always use an existing Role as a template.

2) Click ADD.
An overlay screen will appear on the page.

3) From the left of the screen, select the HelixNet device type you require.
Give the device a name in the Label field. Select a template Role from the
drop-down box.

Page 146
Figure 8-2 Add Role Dialog

4) Click Add. This creates a new role which you will see on the left side of
the page under device type.

5) When you have finished creating new roles, click Done.


Once a Role has been created or cloned it can be edited. To edit a Role, click on it
on the left side of the page so it has an orange highlight. Then access
configuration parameters on the center right of the page.

Page 147
Figure 12-3 Edit Roles
Roles can be deleted in this page.
Note: You cannot delete the default Role

Page 148
13 Core Configuration Manager (CCM)

Figure 13-1 CCM overview


You can configure and control HelixNet units from the web-based Core
Configuration Manager. This includes:
 Linking Main Stations
 Configuring of audio and signalization routing throughout the HelixNet
Link-Group:
o Creating configuration Roles for HelixNet devices (Main Stations,
Remote Stations, Speaker Stations and beltpacks)
o Assigning Roles to devices
o Saving and changing configuration Roles for devices

Page 149
 System monitoring and control. The CCM provides a real-time visual
representation of your working intercom system on the Assignments
page.
 Access to device control menus can be restricted from the CCM.
 Upgrading units.
Note: You can also configure and control HelixNet units using the front panel menu
interfaces on each unit. See:
 5 Configuring and managing the Main Station from device menus
 6 Configuring and managing the Remote Station from device
menus
 8 Configuring and managing the Speaker Station from device
menus
 10 Configuring and managing the HBP-2X Beltpack from device
menus
Note: Some functionality (for example, Roles) is only available from the CCM.

13.1 Access the CCM


To access the Core Configuration Manager, enter the IP address of the HelixNet
Main Station, as displayed on the front panel, into the URL field of your browser.
If the unit is reachable over your network, this will take you to the Overview
page of the CCM that is served by the unit.
Note: Default username and password for the CCM: admin, admin.

13.2 Minimum requirements for the CCM


The CCM is supported on the latest versions of all major web browsers including
Google Chrome, Safari, Firefox, Internet Explorer.
Note: Any IP connectivity in HelixNet requires an Ethernet module in the Main
Station.

Page 150
13.3 Overview page

Figure 13-2 Overview page


Note: There is a navigation bar at the top of the page: Home, Overview, Roles,
Assignments.
As HelixNet Main Stations are added to the group, they appear in this screen. To
access the configuration and control options for any one of the units in the group,
click on the device within the Overview page. Linked units can be configured
either from the host device, or by proxy from this screen.
In this page, Devices, in the upper part of the screen represent the linked Main
Stations. Endpoints, in the lower part of the screen are the devices which are
paired or powerlined to the Main Stations. In this screen, clicking on a Main
Station image will offer comprehensive configuration options. Clicking on an
Endpoint allows you to change its name or Role and to reboot or reset to default.
There is also a troubleshooting option. Click on device images to explore
configuration options available for different devices on this page.
Note: The Home button takes you to the General page of the Main Station your
browser is connected to (the host device) which has an orange highlight.

Page 151
Main Station device image shows: Endpoint device image shows:
Hostname Hostname

Model Selected Role

IP address (orange highlight if this is Model


the device your browser is pointing to,
the host device) Main Station the device is
connected to.
Modules installed on Main Station

13.4 Home page


From the Home page of a Main Station, you can access general functions relating
to the device your browser is pointing to (the host device) and also link devices.
There are two buttons in the left margin, below the device image; General, and
Linking. Click on a button to access a configuration page.

Figure 13-3 Home page

Changing a device hostname from the Home page


To change a device name, click on the existing name and enter a new one. Either
press the <ENTER> key or click the blue check mark to apply changes.
When using hostnames, it is advisable to follow the usual conventions for giving
labels to devices used in electronic communication. For instance; do not use

Page 152
spaces, do not rely on case sensitivity, and make the name meaningful in a way
appropriate to the context. This field can be up to 14 characters.

13.5 General Page


License
Your HelixNet Main Station arrives with a license for 12 Channels. To increase
capacity to 24 Channels, please contact your Clear-Com dealer. You will need to
provide your system ID, listed in this section of the CCM. When you receive a
license code from them, input it here to increase available Channels. Each linked
device must be licensed from the home page of the host device, units cannot be
licensed by proxy.
In a Link Group, each device must be licensed. If one unit has only 12 Channels
and the rest have 24, the whole group will use only 12 Channels by default.
The device system ID can also be found in the device menus screens
(Administration/License/Current).

Upgrade (firmware)
In order to upgrade your device, you will need to import the upgrade file provided
by Clear-Com. You will do this on this page. A linked HelixNet Main Station must
be upgraded from the host device (the device that the browser is currently
addressing). The units cannot be upgraded by proxy.
Note: When upgrading your Main Station, any units connected to it (Remote Stations,
Speaker Stations and beltpacks) will also be upgraded. Please make sure you wait
until total upgrade is complete. Only the Computer to HelixNet Main Station
transfer is shown in this screen. Please check progress of additional devices on
the device menu screens.
Note: All devices in a Link-Group MUST be running the same version of the software.

1) Navigate to Home > General in the CCM.

2) Expand the Upgrade option (click on ‘+’).

3) Click Select File and navigate to the upgrade file (.gz extension). Select
the upgrade file to upload it.

4) When the upgrade file is loaded, Upgrade will light up. When this
happens, click on it to upgrade. When the upgrade is finished, the unit will
reboot by itself.

Change password
Change the password to the Core Configuration Manager local to that device.

Page 153
Maintenance
Reset the unit to factory settings, or reboot the system.
Note: In this context, Reset to Default will erase all Role and Channel information.
Channels will return to Channel ‘n’ where ‘n’ is 1 to 24. Roles will revert to factory
default settings.
To reset Hostname, network, linking, pairing and expansion settings use the
device front panel menus. See 5.7.4 Resetting the Main Station to default (factory
mode) settings.
Note: If the device is a Link-Master it will also erase the Roles of any linked devices.
Please be sure to save any Role configurations you wish to keep before
using Reset to Default.
Support Info provides a ‘snapshot’ of the device’s operational information for
troubleshooting purposes. A file containing Support Info can be sent to Clear-
Com engineers or help desk to aid diagnosis of problems.

13.6 Save/Restore System Settings


This is where you will save the roles and channels configured on your system to
an external storage device. Clicking the green Save button will cause a backup
file to be saved to the download directory. From there it can be renamed and
saved as required.

When restoring configured roles and channels from an external file, clicking on the
red Restore button will allow you to navigate to the location of the saved file. The
file has a .cca extension. Select the file to restore it. If the restore is successful
you will see a ‘successfully restored’ message.
Page 154
Note: Save System Settings in this context will save Role information but not network,
pairing, expansion or linking information.

13.7 Linking page


This is where the linking mode of the HelixNet Main Station is set to either Link-
Master or, if connecting to a Link-Group, Link-Member. When linking a Link-
Member to a Link-Master you will provide the device with the Link-Master IP or
Hostname in this page. If you wish to re-configure a Link-Group, you will change
the link status of the device in this page, which will have the effect of removing it
from the group.
Note: A device’s Hostname is available in the General page of the CCM.

Figure 13-4 Linking page in the CCM


For more information about Linking see 15 Linking in the Core Configuration
Manager (CCM).

Page 155
13.8 Roles Page
To access the Roles page, select Roles from the top navigation bar. On this page
you will create, delete, clone and edit Roles.
Roles available for editing, cloning and configuration are in the left margin of the
page. Role parameters available for configuration are on the right of the page.
To create a Role , click the device type you require on the left hand side of the
page (Main Station, Remote Station, Speaker Station or Beltpack), choose a
template (in the first instance this will be the Default role for that device) and
click ‘ADD’.
To edit a Role click on the required Role in the left of the page. When it is selected
for editing, it will have an orange highlight.
Note: Changes made to Roles here are live.

Page 156
Figure 13-5 The Roles page with example Roles
For more detail about Roles see Chapter 12 Roles.

Audio Assignment
In HelixNet 3.0, audio assignment is achieved in the Roles page. You will assign
audio to a Channel on a Keyset. For a description of a Keyset (available on the
front panel of all devices) see 2.1.1 Main Station/Remote channel keyset and
display. A Main Station, a Remote Station and a Speaker Station have 4 Keysets

Page 157
on each device. Beltpacks have two Keysets on each device (beltpacks can also
have many Channels stacked on one key).

13.9 Assignments page


The Assignments page has two main functions in HelixNet 3.0. From this page in
the CCM you can:
 Change Channel names
 See a real-time, visual representation of devices and Roles in use. Any
changes to the configuration are reflected immediately in this page and
the working system.
This page toggles between Hostname view and Roles view.

Page 158
Figure 13-6 Assignments Page

Page 159
Hostname view
A Hostname is the name given to a physical device in the system, and is the label
used for network communication. Main Station Hostnames can be changed in the
Home page of the CCM. See 13.4.1 Changing a device hostname from the Home
page. Other device Hostnames (Endpoints) can be changed from the Overview
page. Click on any device image to select it.
Program inputs, 2W ports, 4W ports and HRM-4X Audio Output are displayed with
a default label that can be changed from the Roles Page.

Roles view
Roles view indicates the configuration details of Roles selected on devices. Roles
view changes as different configurations are selected and loaded. Program inputs,
2W ports, 4W ports and HRM-4X Audio Output are displayed with a default label
that can be changed from the Roles Page.

Figure 13-7 Hostnames and Roles view

Page 160
Channels
Any audio routed through the HelixNet system is contained within a Channel.
Channels operate as virtual partylines; audio sources assigned to a Channel will
be able to talk and listen to all other sources assigned to the same Channel.

To rename a channel
1) In the Assignments page, click on the blue Channel name to select it

2) Enter the new name.

3) Click the blue check mark or <Enter> to submit change.

Page 161
14 Using the CCM to configure Roles

14.1 Editing Main Station roles


You can edit any Main Station Role including default Roles in the CCM.

Editing the Keyset


Each device has four Keysets, one for each channel. The Keyset is used to control
the Channel. You can configure:
 Which Channel is assigned to the Keyset
 If the Talk key on the Keyset is latching or non-latching

1) From the drop-down list of Roles, select the Role you wish to edit.

2) Select Keyset.

Edit channel assignment


Edit talk latch

Figure 14-1 Editing keysets

3) Select the key you wish to edit (Channel 1, 2, 3, or 4).

4) To assign a different Channel to the key, click Channel Assignment.

Page 162
Figure 14-2

5) Select the channel you require, and then click Done.

6) To configure Talk key operation, click Talk Key, and select Latching
(default), Non-Latching or Disabled.

7) Repeat the above steps for each Keyset.

Editing the Station

1) From the top left of the Roles screen, select Main Station (HMS).

2) From the drop-down list of roles, select the role you wish to edit.

3) Select Station.
You can configure the following:
Setting Options
Description Enter station description
Display Brightness Low
Medium (default)
High

Page 163
Setting Options
Key Brightness High/Low. The default setting. Keys are lit bright when
active and lit dim when inactive.
High/Off. Keys are lit bright when active and are unlit
when inactive.
Low/Off. Keys are lit dim when active and are unlit when
inactive.
Off/Off. Keys are unlit, whether or not they are active or
inactive.
Screensaver Channel Name (default)
Hostname
Role Name
Blank
Disabled
RMK Key (Remote Visible Channels(default)/All Channels/Disabled
Microphone Kill) “Visible Channels” will select Channels visible on device
Keysets. “All Channels” will select all Channels available
on the device; 12 or 24.
Menu Access Enabled (default)
Disabled
All Talk key talks to Visible Channels(default)/All Channels
“Visible Channels” will talk to Channels visible on device
Keysets. “All Channels” will talk to all Channels available
on the device (12 or 24 depending on your license).

4) For each setting, select the option you require.

Editing the Headset


1) From the top left of the Roles screen, select Main Station (HMS).

2) From the drop-down list of roles, select the role you wish to edit.

3) Select Headset.
You can configure the following:
Setting Options
Sidetone Gain Adjust slider control from -18dB to 0dB (Default -12dB)
Headphone Gain 0db (default) to 12dB

Page 164
Setting Options
Headphone Limit Off (default)
+6dB
0dB
-6dB
Sidetone Control Tracking (default)
Non-Tracking
Disabled
HS Mic Type Electret(-15dB)
Dynamic (0dB) (default)
Dynamic (-10dB)

4) For each setting, select the option you require.

Editing the Microphone

1) From the top left of the Roles screen, select Main Station (HMS).

2) From the drop-down list of roles, select the role you wish to edit.

3) Select Microphone.
You can configure the following:
Setting Options
Headroom Normal (default)
High
Contour Filter Enabled (default)
Disabled

4) For each setting, select the option you require.

Editing the Program Input

1) From the top left of the Roles screen, select Main Station (HMS).

2) From the drop-down list of roles, select the role you wish to edit.

3) Select Program Input.


You can configure the following:
Setting Options
Label Use to give the program input a meaningful name

Page 165
Setting Options
Gain Adjust slider control from -12dB to 12dB (Default 0dB)
VOX Disabled (Default)/Enabled
VOX Off Delay 0.5s (Default) – 4 s
IFB Dim Level IFB Disabled
-6 dB
-12 dB
-18 dB
-24 dB
Full Cut
Channel Assignment Select a channel from the list of channels.
GPO trigger Enabled (Default)/Disabled

4) For each setting, select the option you require.


Note: When assigning a program input to a Channel in the CCM, the system assumes
that program input is associated with a device. This will be reflected in the
Assignments page in the CCM, where a program input is assigned to a Channel,
the device hostname rather and the Role name will be visible in Roles view.
Note: When controlling an IFB dim level on a Program Input you must edit the Role for
the device the Program Input comes in on. For instance, if the Program Input is
attached to the Main Station, you will edit the Role for that Main Station and this
will control the dim level on Remotes, Speaker Stations and beltpacks connected
to the Main Station.

Editing the Stage Announce Output


1) From the top left of the Roles screen, select Main Station (HMS).

2) From the drop-down list of roles, select the role you wish to edit.

3) Select Stage Announce Output.


You can configure the following:
Setting Options
Label Give the output port a meaningful name
Gain Adjust slider control from -12dB to 12dB (Default 0dB)
SA Button Latching/Non-Latching (default)

4) For each setting, select the option you require.

Page 166
Editing the Hot Mic Output

1) From the top left of the Roles screen, select Main Station (HMS).

2) From the drop-down list of roles, select the role you wish to edit.

3) Select Hot Mic Output.


You can configure the following:
Setting Options
Gain Adjust slider control from -12dB to 12dB (Default 0dB)

4) For each setting, select the option you require.

Editing the Loudspeaker

1) From the top left of the Roles screen, select Main Station (HMS).

2) From the drop-down list of roles, select the role you wish to edit.

3) Select Loudspeaker.
You can configure the following:
Setting Options
Dim 0 dB (default)
-3 dB
-6 dB
-12 dB
-24 dB

4) For each setting, select the option you require.

14.2 General Purpose Input (GPI) and General Purpose


Output (GPO) triggers.
The GPIs and GPOs can be used to link the system to an external appliance.
The GPI (Opto) enables a Talk or Call button press on any one of the 4 keysets
local to the selected device to be triggered by an external appliance (such as a
foot pedal).
The GPO (Relay), sends a signal to an external appliance (such as a light switch)
that is triggered from the 4 local keysets or (in contrast to the GPO) a signal that
is not local to the selected device. A GPO can be triggered by:
 Talk or Call button press
Page 167
 A call signal
 Detection of audio of any kind on a channel (VOX).

Editing the GPI (Opto)

1) From the top left of the Roles screen, select Main Station (HMS).

2) From the drop-down list of roles, select the role you wish to edit.

3) Select GPI (Opto).

4) For each GPI select the local keyset (1 – 4) and you wish to activate (Talk
or Call).

Editing the GPO

1) From the top left of the Roles screen, select Main Station (HMS).

2) From the drop-down list of roles, select the role you wish to edit.

3) Select GPO (Relay).

Page 168
4) For each GPO, select the signal(s) that you wish to trigger the external
appliance, Local Key Assignment, Detection of Talk from any device
and/or Detection of Call from any device.

5) Select the Channel you require then click Done.

Editing Module slots 1 – 3


Module slots 1 – 3 in the CCM correspond to the modules installed on the back of
your Main Station. If module configuration in the CCM does not match what is on
the device, a warning message will be given in the CCM.
For each module, chose between 3 types:
 None/Ethernet/Fiber
 2-wire
 4-wire

None/Ethernet/Fiber
There are no configuration options associated with this module type.

Page 169
2-wire
For each XLR port (A & B) configure the following to connect 2 audio channels to
analogue partylines:
Setting Options
Label Use to give the port a meaningful name
Channel Choose one from total Channels (12 or 24 depending on
Assignment license)
Program Output Mute (default)
Unmute
Mode Clear-Com (default)
RTS 2-pin
RTS 3-pin
Input Gain -3 dB – 3 dB (default = 0)
Output Gain -3 dB – 3 dB (default = 0)
RMK Input Enabled (default)
Disabled
RMK Output Enabled (default)
Disabled
VOX Enabled (default)
Disabled
VOX Off Delay 0.5 s (default) – 4.0 s
GPO Trigger Enabled (default)
Disabled

4-wire
For each RJ45 port (A & B) configure the following to connect two Channels to an
Eclipse MVX card:

Setting Options
Label Use to give the port a meaningful name
Channel Choose one from total Channels (12 or 24 depending on
Assignment license)
Program Output Mute (default)
Unmute
Input Gain -3 dB – 3 dB (default = 0)
Output Gain -3 dB – 3 dB (default = 0)

Page 170
VOX Enabled (default)
Disabled
VOX Off Delay 0.5 s (default) – 4.0 s
GPO Trigger Enabled (default)
Disabled

14.3 Editing Remote Station roles


Editing the Keyset
See 14.1.1 Editing the Keyset.

Editing the Station

1) From the drop-down list of roles, select the role you wish to edit.

2) Select Station.
You can configure the following:
Setting Options
Description Enter station description
Display Low
Brightness Medium (default)
High
Key Brightness High/Low. The default setting. Keys are lit bright when active
and lit dim when inactive.
High/Off. Keys are lit bright when active and are unlit when
inactive.
Low/Off. Keys are lit dim when active and are unlit when
inactive.
Off/Off. Keys are unlit, whether or not they are active or
inactive.
Screensaver Channel Name (default)
Hostname
Role Name
Blank
Disabled
OPT (RMK) Disabled (Default)/All Channels/Visible Channels. This option
Key allows you to enable RMK on remote stations. See 7.9 Using the
RMK [Remote Mic Kill] key

Page 171
Setting Options
Menu Access Enabled (default)
Disabled
All Talk key Visible Channels (Default)/All Channels
talks to:

3) For each setting, select the option you require.


Note: Each device has the capacity for either 12 or 24 Channels (depending on license).
These will all be enabled if you choose ‘All Channels’. “Visible Channels” enables
only those Channels selected and visible on device Keysets.

Editing the Headset


See 14.1.3 Editing the Headset.

Editing the Microphone


See 14.1.4 Editing the Microphone.

Editing the Program Input


See 14.1.5 Editing the Program Input

Editing the Stage Announce Output


See 14.1.6 Editing the Stage Announce Output

Editing the Hot Mic Output


See 14.1.7 Editing the Hot Mic Output.

Editing the Loudspeaker


See 14.1.8 Editing the Loudspeaker.

Editing the GPI (Opto)


14.2 General Purpose Input (GPI) and General Purpose Output (GPO) triggers.

14.4 Editing Speaker Station roles


Editing the Keyset
See 14.1.1 Editing the Keyset

Editing the Station

1) From the drop-down list of roles, select the role you wish to edit.

2) Select Station.
Page 172
You can configure the following:
Setting Options
Description Enter station description
Display Low
Brightness Medium (default)
High
Key Brightness High/Low. The default setting. Keys are lit bright when active
and lit dim when inactive.
High/Off. Keys are lit bright when active and are unlit when
inactive.
Low/Off. Keys are lit dim when active and are unlit when
inactive.
Off/Off. Keys are unlit, whether or not they are active or
inactive.
Screensaver Channel Name (default)
Hostname
Role Name
Blank
Disabled
Menu Access Enabled (default)
Disabled
Unlatch on Shift Enabled (default)
Disabled

3) For each setting, select the option you require.

Editing the Headset


See 14.1.3 Editing the Headset.

Editing the Microphone


See 14.1.4 Editing the Microphone

Editing the Loudspeaker


See 14.1.8 Editing the Loudspeaker.

14.5 Editing the Beltpack roles


Editing the Keyset
Each Beltpack has two keysets, one for each selected channel. The keyset is used
to control the channel. You can configure:

Page 173
 Whether the talk keys are stacked
 Which channel is assigned to the keyset
 If the Talk key on the keyset is latching or non-latching

1) From the top left of the Roles screen, select Beltpack (HBP).

2) From the drop-down list of roles, select the role you wish to edit.

3) Select Keyset.

4) Select the key you wish to edit.

5) To set a key as stacked, select the Stacked Key checkbox. For detail on
setting stacked keys see 14.7 Configure a stacked key on a beltpack using
the CCM.

6) To assign a different channel to the key, click Channel Assignment.

7) Select the channel you require, and then click Done.

8) To configure Talk key operation, click Talk Key, and select Latching
(default), Non-Latching or Disabled.

9) Repeat the above steps for each keyset.

10) Set USB Flasher Mode (default Disabled). For more detail on USB
flasher functionality see 14.8 Call a beltpack using the USB flasher
feature.

Page 174
Editing the General Settings

1) From the drop-down list of roles, select the role you wish to edit.

2) Select Station.
You can configure the following:
Setting Options
Description Enter station description
Display Low
Brightness Medium (default)
High
Key Brightness High/Low. The default setting. Keys are lit bright when active
and lit dim when inactive.
High/Off. Keys are lit bright when active and are unlit when
inactive.
Low/Off. Keys are lit dim when active and are unlit when
inactive.
Off/Off. Keys are unlit, whether or not they are active or
inactive.
Vibrate on Call Enabled
Disabled (default)
Rotate Display Enabled
Disabled (default)
Screensaver Channel Name (default)
Hostname
Role Name
Blank
Disabled
Menu Access Enabled (default)
Disabled

3) For each setting, select the option you require.

Editing the Headset


See 14.1.3 Editing the Headset.

Editing the Microphone


See 14.1.4 Editing the Microphone

Page 175
14.6 Disable menu access on any device from the CCM
You can disable menu access to any device, from a Main Station to a beltpack, in
the Roles page.

1) Navigate to Roles > Device > Role > Station > Menu Access

2) Select required access mode. <Enter> to select option.

Figure 14-3 Enable/disable menu access

14.7 Configure a stacked key on a beltpack using the


CCM
You can configure stacked keys on a beltpack, putting two or more Channels on
the same key. This enables the beltpack user to talk and listen to two groups
simultaneously. Pressing the Talk or Call button on the beltpack will initiate a talk
or call to all the Channels on the stacked key. If a Channel user activates a call to
the beltpack, the Call label will flash and vibrate is enabled.
Beltpack stacked keys can only be configured through the Core Configuration
Manager (CCM).

Page 176
To configure a stacked key on a beltpack:

1) Navigate to Roles >Beltpack (HBP) > Role > Keysets and select the
Channel tab you wish to stack a key on.

2) Click the Stacked Key checkbox. This automatically unassigns any


Channels already on this Keyset.

3) Click Channel Assignment

4) Select all the Channels you wish to assign to the Keyset. Click Done. The
Channels will be stacked on the Keyset.

5) Set the Talk Key as required.

Figure 14-4 Configure a stacked key

14.8 Call a beltpack using the USB flasher feature


To use this feature you will need a USB-powered light and a micro-to-type A USB
adapter.

1) Set the USB flasher functionality in the beltpack Role.

Page 177
2) Call the beltpack and see the light flashing.

Figure 14-5 Set USB flasher on beltpack

Page 178
15 Linking in the Core Configuration Manager
(CCM)
Main Stations can be linked from the CCM. Each Main Station has 12 Channels
with the option of licensing 12 more (24 in total). When linking Main Stations,
Channels with the same number are merged together into one Channel. Linking
Main Stations will also have the effect of increasing your I/O and device module
options (more beltpacks and a larger area covered).
Note: Linked Main Stations should have the same amount of licensed channels. If you
link a 24 Channel device to a 12 Channel device the system will default to 12
Channels only. To buy a license for more Channels see 13.5.1 License.
Main Stations can still be linked from the device menus. See 16 Linking Main
Stations.

15.1 A HelixNet Link-Group Overview


 A HelixNet Link-Group can contain up to three Main Stations. More is
possible but not advised.
 A Link-Group must have one device designated as Link-Master.
 The Link-Group performs a “best effort” approach to creating a mesh
network between all the devices within the group.

Figure 15-1 A Link-Group

Page 179
The Link-Master
The Link-Master designation serves three main purposes:

1) It facilitates Link-Group membership.

2) It is the owner of configured Role information, meaning that Roles will


only persist (be maintained consistently) if the Link-Master is operational.

3) It is responsible for the synchronization and distribution of both


configuration (Roles) and device availability status throughout the Link-
Group.
Note: Clear-Com recommends that the IP address of the Link-Master is allocated
statically. When allocated by DHCP, the IP address can change. If this happens
the Link-Members will no longer be able to reach the Link-Master device, and Role
information may not be persisted.
Note: Any device can be set to Link-Master or Link-Member. The default setting for
HelixNet linking mode is Linking Disabled. This setting stops the device from
broadcasting its name to the network (via its mDNS index).
Note: Linked Main Stations need 2 – 5 Mbps of bandwidth.

The Link-Members
HelixNet devices that are not identified as master will have the designation of
Link-Member. Joining a device to a Link-Group requires that device to be set to
Link-Member which will prompt the user to enter the IP address of the Link-
Master.

15.2 Device configuration in the CCM


Note: Any IP connectivity requires an Ethernet or Fiber module fitted to the Main
Station.
Once the units have joined a Link-Group, the devices can be configured either
directly or by proxy. The host device is the unit which a browser is currently
directed to.
The Home button will always take you to the host device’s configuration page.
 Proxy configuration can be accomplished by clicking on any device within
the Overview page.

Page 180
Figure 15-2 Host device concept
Note: The host device will always have an orange highlight in the CCM.

15.3 Linking Main Stations in the CCM


Main Stations to be linked in the CCM should first be connected by LAN to the
same network and able to see each other.
In order to create a Link-Group in the CCM, you must designate one unit as Link-
Master. The other units are designated Link-Member and are joined to the Master
via the Master’s IP address. This is achieved in the Linking page of each unit.

1) From a browser, access the CCM of HelixNet Main Station #1 by typing its
IP address into the URL field.

Default login and password for the CCM: admin, admin.


Note: The unit’s IP address can be found in the device’s display screens:
Menu > Networking > Preferences > IP address.
Note: The Link-Master IP must be statically allocated to prevent loss of
service.

2) Navigate to Home > Linking in the CCM. From the drop-down box select
Link-Master and click Apply Changes. This designates this unit as Link-
Master.

Page 181
Note: The default linking mode is: Linking Disabled. When a device has
been designated either Link Master or Link Member it will be
looking for a pairing and a link icon will flash in the device screens.
Linking Disabled prevents this.

3) From a new browser window, access the CCM of device #2 by typing the
unit’s IP address into the URL field.

You will have to enter the password and login for the device (Default,
admin, admin)

4) Navigate to Home > Linking and select Link-Member from the drop down
box.

5) You will be prompted for the IP address (or hostname) of the Link-Master.
Within the Master IP address field, enter the IP address of device #1. Click
on blue check mark or <ENTER> key to submit.

Page 182
Either accept the default Link Group Member ID (orange highlight) or
select a new one by clicking on it. Click Apply Changes. This links this
device to the Link Master.

6) Navigate to the Overview page (top navigation bar). Both HelixNet


devices are now displayed on this page.

7) Repeat steps 3) to 6) for a third device if required.

Page 183
16 Linking Main Stations (cabling and linking
from device menus)
This chapter describes how to link Main Stations using the device menus rather
than the Core Configuration Manager. You can connect Main Stations directly
using Ethernet or Fiber, or connect them over a LAN via Ethernet.
Main Station linking is achieved using interface modules fitted to the extension
bay of the Main Station. There are two modules:
 Ethernet interface module (HLI-ET2). This module provides an Ethernet
connection between Main Stations.
 Fiber interface module (HLI-FBS). This module provides a Fiber
connection between Main Stations.
Each Main Station has 12 channels, and can connect up to 20 beltpacks.
Note: If you change the network topology between any two stations, you must reboot
the stations.

Warning: Both ports are configured to bridge traffic from one port
to the other in order to work in daisy-chain. Spanning Tree Protocol
is not enabled on those ports, therefore do not connect them both to
the same network.

16.1 Linking scenarios


Main Stations are connected together using CAT, CAT5e or CAT6 shielded cable.
They can also be connected using fiber. There are various topologies that you can
create. Some of these are illustrated below.

Linking two Main Stations over LAN

1) Insert an HLI-ET2 Ethernet interface module in each station. Use any of


the three slots available.
Note: Ensure that the Main Station is powered down before
inserting modules.

2) Connect a regular Ethernet cable (for example, CAT5, CAT5e, CAT6,


CAT6e) from one HLI-ET2 port on one station to one HLI-ET2 port on the
other station.

3) Power up both stations. Verify that the green LED on each HLI-ET2 port is
flashing.

Page 184
4) On one HMS go to Networking->Linking->Link Mode menu and select
Master.

5) On the other HMS go to Networking->Linking->Link Mode and select


Member. Then in Networking->Link to Master select the Master HMS
you identified in the previous step..
Note: In HelixNet 3.0 each Main Station has 12 Channels. Linking 3.0 Main Stations will
have the effect of giving you more I/O and module options.
Note: You should see a Link icon on the Main Station display.

Figure 16-1: Linking two stations over LAN

Linking two Main Stations with Fiber

1) Insert an HLI-FBS Fiber interface module in each station. Use any of the
three slots available.
Note: Ensure that the Main Station is powered down before
inserting modules.

2) Ensure that an SFP Transceiver is connected into one HLI-FBS module port
on each station.

3) Connect Two Fibers from one HLI-FBS port on one station to one HLI-FBS
port on the other station. If using Single connector fiber, make sure that
Tx on one goes to Rx on the other.

4) Power up both stations. Verify that the green LED on each HLI- FBS port is
flashing.

5) On one HMS go to Networking->Linking->Link Mode menu and select


Master.
Page 185
6) On the other HMS go to Networking->Linking->Link Mode and select
Member. Then in Networking->Link to Master select the Master HMS
you identified in the previous step.
Note: You should see a Link icon on the Main Station display.
Note: In HelixNet 3.0 each Main Station has 12 Channels. Linking Main
Stations in 3.0 will have the effect of giving you more I/O and
module options.

Figure 16-2: Linking two stations with Fiber

Linking three Main Stations in a daisy chain


You can daisy chain stations following all the instructions of the previous sections
using the second port on one of the HLI-ET2 or HLI-FBS module to connect to a
third station. Then enable linking on the third station. The advantage of daisy
chain is that it does not require any additional equipment for interconnection. The
disadvantage is that if you disconnect or power down a station in the middle it will
break the chain and prevent audio from prevent audio from passing between the
units either side of the break.
You can also mix Ethernet and Fiber in the chain using an additional slot in a
station in the middle of the chain.
Alternatively, you can save a slot by using an HLI-FBS module in the middle
station, populating one port with a fiber SFP transceiver and one port with a
10/100Base-T electrical SFP transceiver.

Page 186
Figure 16-3: Linking three Main Stations in a daisy chain

Resource Sharing between Linked Stations


When Channels are linked, Channels of the same number (1 – 24) will merge
their audio together. This means that any audio available on separate Main
Stations will be heard in the Channel of the same number on a linked Main
Station.
If linked Main Stations do not have the same number of licensed Channels (12 or
24), all devices will default to 12 Channels.

Page 187
17 Linking Remote Stations and Speaker
Stations
This chapter describes how to link Remote and Speaker Stations to Main Stations.
You can connect Remote and Speaker Stations on one of the Digital Intercom
Lines, point-to-point to a Main Station Ethernet interface module (HLI-ET2) or
over an IP network.
Linking to a Main Station over an IP network requires an Ethernet interface
module fitted to the extension bay of the Main Station (HLI-ET2).
Note: If the IP address on a Remote Station or Speaker Station changes, you must
either reboot the Remote Station or disable and then re-enable the DHCP on the
Remote Station.

Warning: Digital intercom lines and the Ethernet connections are


mutually exclusive on Remote and Speaker Stations. If both are
connected it will be detected as a fault, communication over both
ports will stop and both status LEDs will blink RED. This requires
a reboot of the station using Administration > Reset > Reboot

Warning: When changing the connection from digital intercom


line to Ethernet or vice-versa, you must disconnect one cable and
then wait until the unit has detected a loss of connection before
connecting the other cable. Otherwise, they will briefly be
detected as both connected.

Warning: When changing the power connections to a Remote


Station, a network storm error message may appear. If so,
disconnect the power cable, and reboot the Remote Station.

Page 188
17.1 Linking scenarios
There are various topologies that you can create. Some of these are illustrated
below.

Digital Partyline Intercom


Remote and Speaker Stations have Digital Intercom 3-pin XLR connectors (female
and male) and can connect to Main Stations along with Beltpacks.
Note: A Remote or a Speaker Station draws current equivalent to three Beltpacks when
the loudspeaker is in use. If the Remote or Speaker Station is locally powered
using a power supply, it does not draw current from the digital intercom line.

1) Connect an XLR cable from a Main Station to the Remote or Speaker


Station.

2) Power up the Main Station and verify that the Line 1 and Line 2 status LED
are green on Main Station.

3) On a Remote Station you can verify that the Line status LED is steady
green.

Page 189
Ethernet point-to-point link
Remote and Speaker Stations have RJ45 Ethernet connectors and can connect to
Main Stations over Ethernet.

1) Insert an HLI-ET2 Ethernet interface module in the Main Station. Use any
of the three slots available.
Note: Ensure that the Main Station is powered down before
inserting modules.

2) Connect a regular Ethernet cable (for example, CAT5, CAT5e, CAT6,


CAT6e) from one HLI-ET2 port on one station to the Remote or Speaker
Station.

3) Connect an external AC/DC power adapter to the Remote or Speaker


Station

4) Power up both Stations. Verify that the green LEDs on the HLI-ET2 port
and on the Remote or Speaker Station are on.

5) Go to Networking->Pair to Station->By Name on the Remote or


Speaker Station. You should see one entry indicating that the Remote or
Speaker Station has properly detected the Main Station. Select this entry.

6) Go to Station Settings->Keyset Assign and assign channels to any


keyset.

Page 190
Local IP Network

1) Insert an HLI-ET2 Ethernet interface module into the Main Station. Use
any of the three slots available.
Note: Ensure that the Main Station is powered down before
inserting modules.

2) Connect a regular Ethernet cable (for example, CAT5, CAT5e, CAT6,


CAT6e) from one HLI-ET2 port to an Ethernet Switch and connect Remote
or Speaker Stations to Ethernet Switch as well.

3) Connect an external AC/DC power adapter to the Remote or Speaker


Station or connect them on a Power over Ethernet (PoE) port on the
Ethernet Switch.

4) Power up all Stations. Verify that the green LED on the HLI-ET2 port and
on the Remote or Speaker Station is on.

Page 191
5) Go to Networking->Link to Station->By Name on each Remote and
Speaker Station. You should see one entry indicating that the Remote or
Speaker Station has properly detected the Main Station. Select this entry.

6) Go to Station Settings->Keyset Assign and assign channels to any


keyset.

Remote IP Network
Remote and Speaker Stations can connect to a Main Station that is not within the
same network Broadcast Domain.

1) Insert an HLI-ET2 Ethernet interface module in the Main Station. Use any
of the three slots available.
Note: Ensure that the Main Station is powered down before
inserting modules.

2) Connect a regular Ethernet cable (for example, CAT5, CAT5e, CAT6,


CAT6e) from one HLI-ET2 port to a Router/Gateway. Make sure you know
the Gateway IP address for that first subnet.

3) Connect Remote or Speaker Stations to a Router/Gateway. Make sure you


know the Gateway IP address for that second subnet.

Page 192
4) Connect an external AC/DC power adapter to the Remote or Speaker
Station or connect them on a Power over Ethernet (PoE) port on the
Ethernet Switch.

5) Power up all Stations. Verify that the green LED on the HLI-ET2 port and
on the Remote or Speaker Station is on.

6) On the Main Station, go to Networking->Preferences->IP Address


and note the IP address of the Main Station. Make sure that Networking-
>Preferences->Gateway and Networking->Preferences->Netmask
match that of your subnet.

7) On each Remote and Speaker Station make sure that all Networking-
>Preferences match that of your subnet.

8) On each Remote and Speaker Station go to Networking->Link to


Station->By Address and enter the IP address of the Main Station.

9) Go to Station Settings->Keyset Assign and assign channels to any


keyset.

Page 193
Mixed Linking
Here is one example of how all the previous linking could be mixed with Main
Station Linking.

17.2 Networking Specifications


Specification Value
Latency on Powerline 40-80ms (depends on the distance and the number of
Devices (HBP, HRM, HKB) on the line. More distance or
more Devices means more latency)
Latency over IP 30ms + Network Latency
Network
Bandwidth used HRM-4X: 600 kbps to the Main Station, 2.5 Mbps from the
Main Station.
HKB-2X: 300 kbps to the Main Station, 1.5 Mbps from the
Main Station.
IPv4 UDP Port 6001 (Digital Intercom)
TCP Port 6001 (Digital Intercom)
UDP Port 5353 (mDNS)

Page 194
18 Connecting to Other Intercom Systems
This chapter provides basic guidance on connecting your HelixNet Partyline
system to a range of other intercom systems, including:
 Two-wire cabled partyline systems (RTS and Clear-Com Encore®).
 Two-wire / four-wire wireless systems (Tempest, CellCom® /
FreeSpeak®, and the DX210).
 Digital matrix systems (Eclipse® MVX four-wire).
 Two way radio systems.
The HMX-4X Main Station is connected to these systems using the optional Two-
wire and Four-wire interface modules.

18.1 Connecting HelixNet Partyline to Encore®


About Encore
Encore is the plug-and-play analog two-wire partyline system from Clear-Com.
Clear-Com Encore is widely used in theaters, schools, local broadcast stations,
churches and other small to mid-size live productions.
Two and four channel versions of the Encore Main Stations and Remote Stations
are available.
Tip: For more information about Encore, see your Encore documentation or visit the
Analog Partyline Intercom pages on the Clear-Com website:
http://www.clearcom.com/product/partyline.

Page 195
Quick reference: Connecting to Encore

Two-wire connection to Encore Encore Main Station powers the line

HMS-4X Main Station 2W Encore Main Station (MS-70x)

Ensure connection is terminated


Configure the 2W module
Standard microphone cable (switch beside connector is on)
Configure the port as Clear-Com
3-pin XLR connectors Adjust nulling using Sidetone Adjust
Run auto-null
and Listen Adjust controls

HMS-4X Main Station 2W Encore Remote Station (RM-70x)

Power
supply Line must be powered
(Remote Station provides no power).
Or
Encore Main Station
(MS-70x)

Figure 18-1: Two-wire connection to Encore

Page 196
Connecting to an Encore Main Station
Note: The following procedure assumes that a two-wire interface module has been fitted
to the HMS-4X Main Station. For more information about interface modules, see
2.2.1 HMS-4X Main Station rear panel: Interface modules.
Note: A HelixNet system with HLI-2W2 must be able to receive power from an analog
partyline.
To connect your HelixNet Partyline system to an Encore Main Station (for
example, the four channel MS-704):

1) On the HMS-4X Main Station, configure the Module Settings for the two-
wire interface module (Menu mode > Module Settings). For the full
procedure, see 5.6.2 Configuring a Two-wire interface module.
Note: Check that the two-wire module is configured for Clear-Com
systems (the default) and run the Auto-null. Auto-nulling helps
to reduce echo while talking on a two-wire audio system. You must
run auto-null every time you change the cabling.

2) Physically connect the HMS-4X Main Station to the Encore Main Station,
using the 3-pin XLR connectors:
 On the HMS-4X Main Station two-wire interface module.
 On the back panel (rear) of the Encore Main Station.
There are four channels (A, B, C and D), comprising two 3-pin XLR
connectors, on the MS-704.
Connect to the selected channel using standard microphone cabling.
Note: The Two-wire module will not function without an attached power
supply on the analog side of the interface.
Ensure that the connection is terminated (using the termination switch
beside the connectors). The default position for the switch is on.

3) On the Encore (MS-704) Main Station, adjust nulling for the selected
channel (either channel A, B, C or D on the MS-704). Nulling helps to
reduce echo while talking on a two-wire audio system.
Tip: The amount of null that is required changes when you add or remove devices, or
alter the length of the cabling. For optimum performance, Clear-Com recommends
that you adjust the nulling every time you make a change to the system
configuration.
Note: Ensure that all Talk keys/routes are disabled before auto-nulling commences.
To adjust nulling on a channel on the Encore Main Station (MS-704):
a) Turn the screwdriver-adjustable Sidetone Adjust control (just
below the headset connector) to the appropriate level.
Page 197
b) Turn the screwdriver-adjustable Listen level control (the null
control, located just below the channel Talk button and Call LED)
for the channel to the appropriate level.
Tip: If the headset microphone is being used, hum or gently scratch the mic for a
continuous signal source to null on. If a good null is not attainable, switch the
Long / Short DIP switch for the channel to its opposite setting. Use the setting
that produces the best audio quality.
To optimize audio quality, you may also want to adjust the Audio Settings on
the
HMS-4X Main Station. For more information, see 5.2 Configuring the Audio
settings.

Connecting to Encore Remote Stations


Connecting to an Encore Remote Station (for example, the RM-704) is similar to
connecting to an Encore Main Station (see 18.1.2 Quick reference: Connecting
to Encore).
You will require a separate power supply, for example, the PS-702 (two
channel) or PS-704 (four channel) power supply, to power the Remote Station
which is unpowered and any connected wired beltpacks.

18.2 Connecting HelixNet Partyline to RTS (Telex) two-


wire systems
About RTS two-wire systems
HelixNet Partyline is also designed for interoperability with RTS (Telex) TW (two-
wire) analog partyline systems from Telex.
RTS two-wire systems include fully programmable intercom (main) stations,
remote Speaker Stations, two-wire beltpacks, and two-wire power supplies.

Page 198
Quick reference: Two-wire connection to RTS 2W system

2-wire connection to RTS 2W system


Standard mic cable / CAT-5
Configure the 2W module
3-pin XLR connectors
Configure the port as RTS
Run auto-null

HMS-4X Main Station 2W RTS Intercom powered (Main) Station

GND Pwr or Pwr


+ Audio
RTS pinout 1 2 Connect to CH-A or CH-B connectors
options in
Enable CH-A or CH-B. Check that
software: 3 channel LED is lit red
Run auto-null
Audio (Not if pin 2
Pwr + Audio)
You can:
Select different RTS options for A and B
connectors (so pin 2 for audio for A, pin
3 for audio for B)

Configure both connectors for RTS, one


for pin 2 and the other for pin 3.

Figure 18-2: Two-wire connection to RTS 2W system

Page 199
Connecting to an RTS (Telex) intercom station
To connect your HelixNet Partyline system to an RTS intercom station (in this
case,
the 2 channel MCE325 user station):

1) On the HMS-4X Main Station, configure the Module Settings for the two-
wire interface module.
For the full procedure, see 5.6.2 Configuring a Two-wire interface
module.
Ensure that you:
 Configure port(s) for RTS systems. You can select from two
different pinouts when connecting to an RTS two-wire system:
RTS pinout option Description
RTS Audio Pin 2 Pin 2 is used for both power and
audio.
RTS Audio Pin 3 Pin 3 is used for audio (Pin 2 is
used for power only).
Table 18-1: Configuring Module Settings: RTS pinout options
 Run auto-null. Auto-nulling helps to reduce echo while talking
on a two-wire audio system. You must run auto-null every time
you change the cabling.

2) Physically connect the HMS-4X Main Station to the RTS intercom station
(MCE325).The two channels of RTS TW intercom must be split prior to
connection with either of the Two-wire module ports. RTS Audio Pin 2
carries the power that is required for the Two-wire module.
Powering the connection:
You must power the connection between the systems using either a
dedicated power supply or an RTS power supply.
Tip: For more information about the PK-7 or PS-70x power supply devices from Clear-
Com, see http://www.clearcom.com/product/partyline/power-supplies
Connecting to the MCE325 device:
There are three 3-pin XLR connectors on the rear panel of the MCE325
device. In two-wire mode:
 The left and right-hand connectors are used for intercom
channels 1 and 2 input/ output.
 The center connector is used for channels 3 and 4 input /
output.

Page 200
 Connect to the selected channel using standard microphone
cabling.
Note: The MCE325 is designed for use with intercom lines with a 200-
ohm line terminating impedance. A 200 ohm termination plug is
connected to the center 3-pin XLR connector to prevent channels 3
and 4 from oscillating when the MCE325 is in two-channel mode.

3) On the RTS device (in this case, the MCE325), adjust the nulling (if
necessary) on the channel to which the HMS-4X Main Station is
connected.
Nulling helps to reduce echo while talking on a two-wire audio system. A
sidetone nulling trimmer (control) is provided for each of the four
channels on the device.
To adjust a sidetone nulling trimmer:
a) Turn the speaker switch on (even if an external speaker is not
connected). This turns off the internal sidetone trimmer, which
controls the sidetone level in headsets.
b) Turn on the microphone. Activate the relevant Talk button and
speak into the microphone.
c) To minimize echo, adjust the sidetone nulling trimmer (located
under the CH1 and CH2 rotary controls).
Note: The default setting for each trimmer is for maximum nulling of the
microphone signal when a 200-ohm resistance terminates the
channel. However, you may have to adjust the nulling according to
the system configuration.

18.3 Connecting HelixNet Partyline to Tempest®


About Tempest
Tempest is a digital wireless intercom system, comprising a base station (Main
Station) and belt stations (beltpacks). There are two-wire and four-wire versions
of Tempest available. The system operates in either:
 The 2.4GHz ISM band (Tempest 2400 models).
 The 900 MHz ISM band (Tempest 900 models).
Tip: For more information about Tempest, see your Tempest documentation or visit
the wireless intercom pages on the Clear-Com website:
http://www.clearcom.com/product/wireless.

Page 201
Quick reference: Two-wire connection to Tempest

Two-wire connection to
Standard mic cable / CAT-5 Select Clear-Com as the intercom type
Tempest 3-pin XLR connectors Select the connected channel (A or B)
Select 2W mode
Run auto-null

HMS-4X Main Station 2W Tempest Basestation

Power
supply Line must be powered (HMS-4X 2W
Configure the 2W module module appears as unpowered
Or beltpack / remote station to Tempest).
Configure the port as Clear-Com
Run auto-null Encore Main Station
(MS-20x)

Figure 18-3: Two-wire connection to Tempest

Page 202
Two-wire connection to Tempest
To connect your HelixNet Partyline system to Tempest, using a two-wire
connection:

1) On the HMS-4X Main Station, configure the Module Settings for the two-
wire interface module.
For the full procedure, see 5.6.2 Configuring a Two-wire interface
module.
Note: Check that the Two-wire module is configured for Clear-Com
systems (the default) and run Auto-null. Auto-nulling helps to
reduce echo while talking on a two-wire audio system. You must
run auto-null every time you change the cabling.

2) On the Tempest base station:


a) Select Clear-Com as the intercom type, using the slide switch on
the front panel.
b) Configure an intercom channel for two-wire connection:
i. Select the intercom channel (A or B), using the CHAN
selection button on the front panel.
ii. Select two-wire connection for the intercom channel, using
the two-wire / four-wire selection button on the front
panel.
c) Enable Auto-null, using the Tempest menu screens. Enable
Manual Null to remove any residual echo, where desired.
For more detailed information about setting up a two-wire connection on
the Tempest base station, see your Tempest reference manual.

Always set the intercom type before you connect a two-wire


intercom system to the Tempest Base station.

Never change the setting while the systems are connected.


Changing the setting while the systems are connected can damage
the Tempest Base station and / or the other system (in this case,
HelixNet Partyline).

3) Physically connect the HelixNet Partyline and Tempest systems.


Powering the connection:
Tempest has a Master Mode setting that supplies power to the two-wire
connection. In this case, no external power supply is required. Otherwise,
you must power the connection between the systems using either a
Page 203
dedicated power supply (such as the PK-7, PS-702, or PS-704), or a
powered Encore Main Station (such as the MS-702 or MS-704).
Tip: For more information about the PK-7 or PS-70x power supply devices from Clear-
Com, see http://www.clearcom.com/product/partyline/power-supplies
Connecting to Tempest:
You can use standard microphone cable or CAT5 cable types to connect
the HMS-4X Main Station to the Tempest Base station. 3-pin XLR
connectors are located:
 On the HMS-4X Main Station two-wire interface module.
 On the back panel (rear) of the Tempest Base station.
Tip: Tempest provides two-wire input/output gain adjustments, and can be utilized to
either balance the gains between HelixNet and Tempest or connect two-wire
system interfaces through a Tempest base station.

4) Adjust the In / Out volume level controls on the Tempest Base station.
The In / Out volume levels have the following ranges:
Volume level Range
In -18dB to +4dB
Out -18dB to +4dB
Table 18-2: Tempest Base station In / Out volume levels
For more information, see your Tempest reference manual.
Tip: To optimize audio quality, you may also want to adjust the Audio Settings on
the
HMS-4X Main Station. For more information, see 5.2 Configuring the Audio
settings.

Page 204
Quick reference: Four-wire connection to Tempest

Four-wire connection to Tempest


4W crossover cable (CAT-5) Select Clear-Com as the intercom type
Configure the 4W module RJ45 connectors Select the connected channel (A or B)
Select 4W mode
Adjust the In / Out levels

HMS-4X Main Station 4W


2W Tempest Basestation

Pin Function Pin Function


1 Data out + 1 N/C
2 Data out - 2 N/C
3 Audio out + 3 Audio out +
4 Audio in + 4 Audio in +
5 Audio in - 5 Audio in -
6 Audio out - 6 Audio out -
7 Data in + 7 N/C
8 Data in - 8 N/C

Figure 18-4: Four-wire connection to Tempest

Page 205
Four-wire connection with Tempest
To connect your HelixNet Partyline system with Tempest, using a four-wire
connection:

1) On the HMS-4X Main Station, configure the Module Settings for the
Four-wire interface module, see 5.6.1 Configuring a Four-wire
interface module.

2) On the Tempest Base station, configure an intercom channel for four-wire


connection:
a) Select the intercom channel (A or B), using the CHAN selection
button on the front panel.
b) Select four-wire connection for the intercom channel, using the
two-wire / four-wire selection button on the front panel.

3) Connect the HMS-4X Main Station and the Tempest Base station, using
four-wire crossover CAT5 cabling.
Note: For pinout information for the two systems, see the quick
reference diagram in 18.3.4. Quick reference: Four-wire
connection to Tempest.
RJ45 connectors are located:
 On the HMS-4X Main Station four-wire interface module.
 On the back panel (rear) of the Tempest Base station (the top
RJ45 connector is for intercom channel A and the bottom
RJ45 connector for intercom channel B).

4) Adjust the In / Out levels controls on the Tempest Base station, where
necessary.
For more information, see your Tempest reference manual.
Tip: To optimize audio quality, you may also want to adjust the Audio Settings on
the HMS-4X Main Station. For more information, see 5.2 Configuring the Audio
settings.

Page 206
18.4 Connecting HelixNet Partyline to CellCom® /
FreeSpeak®
About CellCom / FreeSpeak
CellCom / FreeSpeak is a wireless intercom system from Clear-Com, operating
within the license-free 1.92-1.93GHz frequency band. The system is branded as
CellCom in North America and as FreeSpeak in the rest of the world.
CellCom /FreeSpeak combines DECT and wireless auto-roaming technologies to
allow users to move freely without losing communication connection. Active
Antennas enable a beltpack-to-base station distance range of up to 3200ft
(1000m).
You can connect up to 20 full-duplex wireless beltpacks (which operate as fully
programmable mobile panels) to one CellCom / FreeSpeak base station (Main
Station).
Note: CellCom / FreeSpeak can also operate as an integrated solution, with up to 35
beltpacks connected to a Clear-Com digital Matrix frame.
Tip: For more information about CellCom / FreeSpeak, see your CellCom / FreeSpeak
documentation or visit the wireless intercom pages on the Clear-Com website:
http://www.clearcom.com/product/wireless.

Page 207
Quick reference: Two-wire connection to CellCom / FreeSpeak

Two-wire connection to CellCom / FreeSpeak


Standard mic cable / CAT-5
3-pin XLR connectors

HMS-4X Main Station 2W CellCom / FreeSpeak Basestation

Power
supply
Connect to CH-A or CH-B connectors
Configure the 2W module Or
Enable CH-A or CH-B. Check that
Configure the port as Clear-Com Encore Main Station channel LED is lit red
Run auto-null (MS-70x) Run auto-null

Line must be powered


(HMS-4X 2W module appears as unpowered
beltpack / remote station to CellCom / FreeSpeak).

Figure 18-5: Two-wire connection to CellCom / FreeSpeak

Page 208
Two-wire connection to CellCom / FreeSpeak
To connect your HelixNet Partyline system to a CellCom / FreeSpeak base station
(Main Station), using a two-wire connection:

1) On the HMS-4X Main Station, configure the Module Settings for the two-
wire interface module. See 5.6.2 Configuring a Two-wire interface
module.
Note: Check that the two-wire module is configured for Clear-Com
systems (the default) and enable Auto-nulling. Auto-nulling
helps to reduce echo while talking on a two-wire audio system.

2) There are two partyline channels on the CellCom / FreeSpeak base station
(CH-A and CH-B). Before connecting the HMS-4X Main Station to the
base station, ensure that the partyline LED on the front panel for the
selected channel is off.
Off indicates that the partyline connection is currently disabled from the
base station.
Note: If the channel is currently enabled, the partyline LED is lit red.

3) Physically connect the HMS-4X Main Station to one of the two partyline
channels on the CellCom / FreeSpeak base station (Main Station).
Powering the connection:
You must power the connection between the systems using either a
dedicated power supply (such as the PK-7, PS-702, or PS-704), or a
powered Encore Main Station (such as the MS-702 or MS-704).
Tip: For more information about the PK-7 or PS-70x power supply devices from Clear-
Com, see http://www.clearcom.com/product/partyline/power-supplies
Connecting the systems:
Use standard microphone cable to connect the two systems. There are 3-
pin XLR connectors:
 On the HMS-4X Main Station two-wire interface module.
 On the back panel of the CellCom / FreeSpeak Base station.
Two 3-pin XLR connectors, one male, one female, are provided
for each of the two partyline channels (CH-A and CH-B).

4) On the CellCom / FreeSpeak base station, press Enable on the front panel
(located directly beneath the LED for the connected channel (CH-A or CH-
B)).The LED for the channel is lit red.
The base station automatically detects and configures the appropriate
power and termination settings when the channel is enabled. The base

Page 209
station also remembers that the channel is enabled the next time the base
station is powered up.

5) On the CellCom / FreeSpeak base station, press Enable again and hold.
The base station activates auto-nulling on the connected channel. Auto-
nulling helps to reduce echo while talking on a two-wire audio system.

Page 210
Quick reference: Four-wire connection to CellCom / FreeSpeak

Four-wire connection to CellCom / FreeSpeak


4W crossover cable (CAT-5) Select PORTS > 4-WIRE > CALLS, then
Configure the 4W module RJ45 connectors select a port / group as the destination
for the incoming 4-wire audio
Adjust the In / Out levels

HMS-4X Main Station 4W


2W CellCom / FreeSpeak Basestation

Pin Function Pin Function


1 Data out + 1 N/C
2 Data out - 2 N/C
3 Audio out + 3 Audio out +
4 Audio in + 4 Audio in +
5 Audio in - 5 Audio in -
6 Audio out - 6 Audio out -
7 Data in + 7 N/C
8 Data in - 8 N/C

Figure 18-6: Four-wire connection to CellCom / FreeSpeak

Page 211
Four-wire connection to CellCom / FreeSpeak
To connect your HelixNet Partyline system with a CellCom / FreeSpeak base
station (Main Station), using a four-wire connection:

1) On the HMS-4X Main Station, configure the Module Settings for the four-
wire interface module. For the procedure, see 5.6.1 Configuring a Four-
wire interface module.

2) Connect the HMS-4X Main Station and the CellCom / FreeSpeak base
station, using four-wire crossover CAT5 cabling.
Note: For pinout information for the two systems, see the quick
reference diagram in 18.4.4 Quick reference: Four-wire
connection to CellCom / FreeSpeak.
RJ-45 connectors are located:
 On the HMS-4X Main Station four-wire interface module.
 On the back panel (rear) of the CellCom / FreeSpeak base
station. There are four RJ45 connectors for four-wire
connections on the base station.

3) Adjust the In / Out volume levels, using the CellCom / FreeSpeak front
panel display. For more information, see your CellCom / FreeSpeak
documentation.
Tip: To optimize audio quality, you may also want to adjust the Audio Settings on
the HMS-4X Main Station. For more information, see 5.2 Configuring the Audio
settings.

18.5 Connecting HelixNet Partyline to the DX210


About the DX210
The Clear-Com HME DX210 is a 2 channel wireless intercom system. The base
station (Main Station) supports up to 15 beltpacks or all-in-one headsets
(headsets operating as beltpacks).
The DX210 supports Clear-Com and RTS cabled two-wire intercom systems, and
also has four-wire and auxiliary audio connections.
The DX210 operates in the license-free 2.4GHz band, and has provisions for
spectrum-friendly co-existence with other devices in the same band.
Tip: For more information about the DX210, see your DX210 documentation or visit
the wireless intercom pages on the Clear-Com website:
http://www.clearcom.com/product/wireless.

Page 212
Quick reference: Two-wire connection to DX210

Two-wire connection to DX210


Standard microphone cable
3-pin XLR connectors

HMS-4X Main Station 2W DX210 Basestation (BS210)

Configure the 2W module Power supply


Configure the port as Clear-Com
Run auto-null
Or
Set Clear-Com / RTS button to Clear-Com (out position)
Encore Main Station Connect to either intercom channel (IC1 or IC2). Press
(MS-70x) the SELECT button for connected channel
Run auto-null using the AUTO-NULL control
Adjust In / Out levels with 2W-INPUT and 2W-OUTPUT
controls for the channel

Line must be powered (HMS-4X 2W module appears as


unpowered beltpack / Communicator to DX210).

Figure 18-7: two-wire connection to DX210

Page 213
Two-wire connection to the DX210
To connect your HelixNet Party-line system to the DX210 base station (Main
Station), using a two-wire connection:

1) On the HMS-4X Main Station, configure the Module Settings for the Two-
wire interface module. For the procedure, see 5.6.2 Configuring a Two-
wire interface module.
Note: Check that the two-wire module is configured for Clear-Com
systems (the default) and run Auto-null. Auto-nulling helps to
reduce echo while talking on a two-wire audio system. You must
run auto-null every time you change the cabling.

2) On the rear panel of the DX210 base station, ensure that the Clear-Com
/ RTS button is set to Clear-Com mode (the out position).

3) Physically connect the HMS-4X Main Station to one of the two intercom
channels on the DX210 base station (Main Station).
Powering the connection:
You must power the connection between the systems using either a
dedicated power supply (such as the PK-7, PS-702, or PS-704), or a
powered Encore Main Station (such as the MS-702 or MS-704).
Tip: For more information about the dedicated power supply devices (PK-7 or PS-70x
devices) from Clear-Com, see http://www.clearcom.com/product/partyline/power-
supplies
Connecting the systems:
Use standard microphone cable to connect the two systems. 3-pin XLR
connectors are located:
 On the HMS-4X Main Station two-wire interface module.
 On the back panel (rear) of the DX210 base station.
Two 3-pin XLR connectors (one male, one female) are provided for each of
the two intercom channels (IC1 and IC2) on the base station.

4) On the front panel of the DX210 base station, press the SELECT button
for the connected intercom channel (either IC1 or IC2).
The 2-W (two-wire) LED next to the SELECT button is lit green.
Note: If power is not detected at the connector, the 2-W LED is lit red.
No audio can be transmitted between the systems. When the
HMS-4X Main Station is powered, power is supplied to the
connection and the 2-W LED is lit green.

Page 214
5) Apply auto-nulling to the connected channel (either IC1 or IC2) on the
DX210 base station. Auto-nulling helps to reduce echo while talking on a
two-wire audio system. To apply auto-nulling:
a) Insert a pen or similar pointed object into the AUTO-NULL hole on
the front panel.
b) Press and hold AUTO-NULL for 2 seconds.
Note: Before applying auto-nulling, ensure that there are no open
microphones on the wired intercom. If users are wearing headsets,
you must notify them of the audio-sweep that precedes the
application of auto-nulling.

6) Adjust the two-wire intercom receive and send levels (in / out levels),
using the 2-W INPUT and 2-W OUTPUT controls for the connected
channel (IC1 or IC2) on the DX210 base station front panel. For more
information, see your DX210 documentation.
Tip: To optimize audio quality, you may also want to adjust the Audio Settings on
the HMS-4X Main Station. For more information, see 5.2 Configuring the Audio
settings.

Page 215
Quick reference: Four-wire connection to DX210

Four-wire connection to DX210


Connect to either intercom channel (IC1 or IC2).
Press the SELECT button for connected channel
4W crossover cable (CAT-5)
Configure the 4W module Adjust In / Out levels with 4W-INPUT and 4W-
RJ45 connectors
OUTPUT controls for the channel

HMS-4X Main Station 4W


2W DX210 Basestation (BS210)

Pin Function Pin Function


1 Data out + 1 N/C
2 Data out - 2 N/C
3 Audio out + 3 Audio out +
4 Audio in + 4 Audio in +
5 Audio in - 5 Audio in -
6 Audio out - 6 Audio out -
7 Data in + 7 N/C
8 Data in - 8 N/C

Figure 18-8: Four-wire connection to DX210

Page 216
Four-wire connection to the DX210
To connect your HelixNet Partyline system with a DX210 base station (BS210),
using a four-wire connection:

1) On the HMS-4X Main Station, configure the Module Settings for the
Four-wire interface module. See 5.6.1 Configuring a Four-wire
interface module.

2) Connect the HMS-4X Main Station and the DX210 base station (BS210),
using four-wire crossover CAT5 cabling.
Note: For pinout information for the two systems, see the quick
reference diagram in 18.5.4 Quick reference: Four-wire
connection to DX210.
RJ45 connectors are located:
 On the HMS-4X Main Station Four-wire interface module.
 On the back panel (rear) of the DX210 base station (BS210).
There is an RJ45 (four-wire) connector for each of the intercom channels
on the DX210 base station (IC1 and IC2). Connect the systems with a
four-wire crossover CAT5 cable.

3) Adjust the In / Out volume levels, using the CellCom / FreeSpeak front
panel display. For more information, see your CellCom / FreeSpeak
documentation.
Tip: To optimize audio quality, you may also want to adjust the Audio Settings on
the
HMS-4X Main Station. For more information, see 5.2 Configuring the Audio
settings

18.6 Connecting HelixNet Partyline to Eclipse®


About Eclipse
Eclipse is the digital matrix system from Clear-Com. A wide choice of system
frames, system cards and modules enables the unification of multiple intercom
systems (digital, analog, wired and wireless) in a single intercoms infrastructure.
Eclipse is configured, managed and maintained using the intuitive Eclipse
Configuration Software (EHX). The Production Maestro® software provides a
centralized routing tool, to assist with four-wire configurations. Logic Maestro is a
graphical programming tool for ECS, simplifying the design and programming of
complex logical functions.
The following procedures reference the following Eclipse devices:

Page 217
 The Eclipse or Eclipse-HX system frame. For example, the Eclipse
Median is a 6RU frame that houses 2 CPU and 7 matrix slots with 8 built-
in interface module slots.
 The CCI-22 interface module. The CCI-22 is the two-wire party-line
interface (Clear-Com and / or RTS) to Eclipse. ECS views a direct, four-
wire HelixNet Party-line connection with the system frame as a ‘virtual’
CCI-22 connection.
Tip: For more information about Eclipse, see your Eclipse / EHX documentation or visit
the digital matrix pages on the Clear-Com website:
http://www.clearcom.com/product/digital-matrix.

Page 218
Quick reference: Two-wire connection to Eclipse

2-wire connection to Eclipse


Adjust nulling
Adjust In / Out levels (if necessary)

3-pin XLR connector to DB9 connector


There is a
cat5 cable
that is a patch
from one
HMS-4X Main Station 2W CCI-22 Eclipse panel to
Median another on
the median
Power frame.
Configure the 2W module supply
Configure the port as Clear-Com Example connection:
Or 3-pin XLR to DB9M on CCI-22 Optional Clear-
Run auto-null Com / RTS
Encore Main Station external switch
(MS-70x) (on CCI-22)
1
Pwr 6
GND 2
7
Line must be powered (CCI-22 1 2 3
8
module views HMS-4X Main 3 4
Station as an unpowered 9
Audio 5
beltpack / remote station) 0.01 uF To chassis
ground on frame

Figure 18-9: Two-wire connection to an Eclipse Matrix

Page 219
Two-wire connection to an Eclipse or Eclipse-HX system
frame
To connect your HelixNet Partyline system to an Eclipse or Eclipse-HX System,
using a two-wire connection:

1) On the HMS-4X Main Station, configure the Module Settings for the Two-
wire interface module. For the procedure, see 5.6.2 Configuring a Two-
wire interface module.
Note: Check that the two-wire module is configured for Clear-Com
systems (the default) and run Auto-null. Auto-nulling helps to
reduce echo while talking on a two-wire audio system. You must
run auto-null every time you change the cabling.

2) Physically connect the HMS-4X Main Station to the CCI-22 dual-channel


party-line interface module.
The CCI-22 may be fitted:
 Directly to an Eclipse or Eclipse-HX System.
 An interface frame (such as the IMF-3 or IMF-102), connected
to the Eclipse matrix.
Tip: For more information about installing and using the CCI-22, see the CCI-22
Manual, or go to: http://www.clearcom.com/product/digital-matrix/interface-
modules/cci-22
Powering the connection:
You must power the connection between the HMS-4X Main Station and the
CCI-22 using either a dedicated power supply (such as the PK-7, PS-702,
or PS-704), or a powered Encore Main Station (such as the MS-702 or MS-
704).
Tip: For more information about the PK-7 or PS-70x power supply devices from Clear-
Com, see http://www.clearcom.com/product/partyline/power-supplies
Connecting the systems:
There are two parallel DB-9M Interface I/O connectors on the CCI-22. The
two-wire module on the HMS-4X Main Station features two 3-pin XLR
connectors. For more information about wiring the connection, see:
 18.6.2 Quick reference: Two-wire connection to Eclipse.
 The CCI-22 Manual.

3) Apply nulling to the connected channel on the CCI-22. To null the channel:
a) Insert the accessory earphone into the front-panel Test jack. A test
tone, for all frequencies, is produced every 0.5s.

Page 220
b) While listening to the test tone, adjust the R (Resistance) control
until the tone is at a minimum.
c) Repeat Step b. for the L (Inductance) and C (Capacitance) controls.
These controls compensate for each component of the line’s
impedance, providing the best possible null.
Because the R, L and C controls interact, you may have to adjust these
controls several times to minimize the test tone / achieve a deep null.
Note: The null circuit on the CCI-22 is effective on line lengths between
0 - 4000 feet (1200m) with impedances in the range of 120 to 350
ohms. Nulling can reduce local audio in the received signal by < 30
dB over the 200 Hz - 8 kHz frequency range.
Tip: For more information on the CCI-22 nulling circuit, see the CCI-22 Manual.

4) If necessary, adjust the In / Out level controls on the CCI-22 (Send and
Recv, located on the front panel next to the R, L and C nulling controls).
Note: The Send level control affects the level of the audio signals from
the
Eclipse Matrix to the external party-line, and the Recv control affects the
level of the audio from the party-line into the matrix. The Send and
Receive controls have a range of ± 13 dB.
Tip: For more information about managing the HelixNet to Eclipse connection in EHX,
see your EHX documentation (including Help).

Page 221
Quick reference: Four-wire connection to Eclipse

Four-wire connection to Eclipse


RJ45 connectors located on rear panel of
MVX-A16, the 16 port audio and data
card set

Configure the 4W module


1:1 direct CAT-5 connection
RJ45 connectors

MVX- Eclipse
HMS-4X Main Station 4W
2W
A16 Median

No pinout compatibility issues


(no crossover cable required)

Figure 18-10: Four-wire connection to Eclipse Matrix

Page 222
Four-wire connection to Eclipse
To connect your HelixNet Partyline system to an Eclipse or Eclipse-HX System,
using a four-wire connection:

1) On the HMS-4X Main Station, configure the Module Settings for the four-
wire interface module For the procedure, see 5.6.1 Configuring a Four-
wire interface module.

2) Connect the HMS-4X Main Station directly to the MVX-A16 card (the 16
port audio and data card set) with standard CAT5 cable.
Note: For pinout information for the two systems, see the quick
reference diagram in 18.6.4 Quick reference: Four-wire
connection to Eclipse.
RJ45 connectors are located:
 On the HMS-4X Main Station four-wire interface module.
 On the rear panel of the MVX-A16 card.
Tip: To optimize audio quality, you may want to adjust the Audio Settings on the
HMS-4X Main Station. For more information, see 5.2 Configuring the Audio
settings
Tip: For more information about managing the HelixNet to Eclipse connection in EHX,
see your EHX documentation (including EHX Help).

18.7 Connecting HelixNet Partyline to two-way radio


systems
Two-way radio systems (also known as walkie-talkies) are widely used for
wireless communication where quick deployment is a required.
HelixNet can interface to a two-way radio system audio along with transmit key
control.
The following examples show how you can setup HelixNet to activate a relay on a
Main Station or a Remote Station every time someone activates a Talk key on the
selected Partyline Channel.
Note: HelixNet provides and expects 4W audio at line level (0dBu).

Page 223
Quick Reference: four-wire and control connection to radio system

Four-wire connection to radio system


Configure the 4W module

HMS-4X Main Station 2W


4W Radio basestation

4W RJ45 connector Control I/O D-type connector

Pin Function Pin Function Pin Function


1 Data out + 1 Relay 1 NC 14 Relay 1 Pole
2 Data out - 2 Relay 1 NO 15 Relay 2 NC
3 Audio out + 3 Relay 2 Pole 16 Relay 2 NO
4 Audio in + 4 Relay 3 NC 17 Relay 3 Pole
5 Audio in - 5 Relay 3 NO 18 Relay 4 NC
6 Audio out - 6 Relay 4 Pole 19 Relay 4 NO
7 Data in + 7 20 +5V
8 Data in - 8 GND 21 +5V
9 GND 22 Opto 1-
10 Opto 1+ 23 Opto 2-
11 Opto 2+ 24 Opto 3-
12 Opto 3+ 25 Opto 4-
13 Opto 4+

Figure 18-11 Four-wire and control connection to radio system

Page 224
Four-wire and control connection to radio system
To connect the HelixNet Partyline to a radio system using four-wire:

1) In the Modules Settings menu, select Slot n/Port A/B 4W > Channel
Assign > Channel # to assign the 4W port to a Channel, for example
Channel A.

2) In the Modules Settings menu, select Slot n/Port A/B 4W > GPO
Trigger > Disable to set GPO Trigger to Disable for that 4W port.

3) In the Channels menu, select Channel # > GPO on Talk > Relay # to
select a Relay.

4) Connect the 4W audio and the configured Relay to the radio base station.

Page 225
Quick reference: two-wire and control connection to radio system

Two-wire connection to radio system

Encore Main Station powers the line

Encore Main Station


HMS-4X Main Station 2W TW-47 Radio Interface Radio basestation
(MS-70x)

Configure the 2W module


Shield Power/TW
Configure the port as Clear-Com Standard microphone cable Channel A
Run auto-null 3-pin XLR connectors 1 2
TW-47
pinout 3

Intercom audio/
TW Channel B

Figure 18-12 Two-wire and control connection to radio system

Page 226
Two-wire and control connection to radio system
The two-wire connection uses a TW-47 radio interface. Because this has no power
supply, you must use an Encore Main Station to supply power. You can also use
an alternative source of power, such as a PK-7, PS-702 or PS-704.
The diagram in Figure 18-12 shows a system using an Encore Main Station.
To connect the HelixNet Partyline to a radio system using two-wire:

1) Connect the HelixNet Partyline to the Encore Main Station. For details, see
18.1 Connecting HelixNet Partyline to Encore®.

2) In the Modules Settings menu, select Slot n/Port A/B 2W > Channel
Assign > Channel # to assign the 2W port to a Channel, for example
Channel A.

3) Connect the Encore Main Station to the TW-47 radio interface.

4) Connect the TW-47 radio interface to the radio base station.

Page 227
Quick reference: Main Station connection to radio system

Four-wire connection to radio system


Configure the 4W module

HMS-4X Main Station 4W


2W Radio basestation

Control I/O D-type connector

Pin Function Pin Function


1 Relay 1 NC 14 Relay 1 Pole
2 Relay 1 NO 15 Relay 2 NC
3 Relay 2 Pole 16 Relay 2 NO
4 Relay 3 NC 17 Relay 3 Pole
5 Relay 3 NO 18 Relay 4 NC
6 Relay 4 Pole 19 Relay 4 NO
7 20 +5V
8 GND 21 +5V
9 GND 22 Opto 1-
10 Opto 1+ 23 Opto 2-
11 Opto 2+ 24 Opto 3-
12 Opto 3+ 25 Opto 4-
13 Opto 4+

Figure 18-13 Main Station connection to radio system

Page 228
To connect the HelixNet Main Station to a radio system using four-wire:

1) In the Audio Settings menu, select PGM/Audio In > GPO Trigger >
Disable.

2) In the Audio Settings menu, select SA/Audio Out Mode > Channel
Assign.

3) Assign the SA/Audio Out to a Channel.

4) In the Channel configuration select the Remote Station Program under


the Program Listen menu.

5) In the Channels menu, select Channel # > GPO on Talk > Relay 1.

6) Connect the audio and the Relay to the radio base station.

Page 229
19 Specifications

19.1 Main Station (HMS-4X)


Connectors
Specification Description / value

Intercom Powerline Outputs Four 3-pin XLR. Two male and two female.

Headset 4-pin XLR–M

USB USB Type A and Micro-AB

Program 3-pin XLR–F

SA (Stage Announce) 3-pin XLR–M

Hot Mic / IFB Interface 1/4 in. (0.64 cm) phone jack

GPIO 25 way D-type female

Table 19-1: Main Station: Connectors

Microphone pre-amplifier
Specification Description / value

Headset Mic impedance: 200Ω (Dynamic)

Headset Mic Voltage 1.7V (Electret selectable)

Limiter +23dB

The following specified for a route to 4-wire output @ 0dBu out

Mic gain 60dB (dynamic) 45dB (electret)

Frequency response 300Hz – 10kHz ± -3dB (contoured for


intelligibility)

Distortion <0.2% THD @ 1kHz

Noise- <-55dBu dynamic, <-65dBu electret

Table 19-2: Main Station: Microphone pre-amplifier

Page 230
Headphone amplifier
Specification Description / value

Load impedance 32Ω

Output level +12dBu before clipping

Sidetone -12dB (selectable)

The following specified for a route from a 4-wire input @ 0dBu in

Max gain 0dB

Frequency response 40Hz - 10kHz ± 3dB

Distortion <0.1% THD @ 1kHz

Noise <-65dBu

Headphone limiter 0dBu (selectable)

Table 19-3: Main Station: Headphone amplifier

Loudspeaker amplifier
Specification Description / value

Load impedance 8Ω

Output level +18dBu before clipping

Max gain 18dB

The following specified for a route from a 4-wire input @ 0dBu in

Frequency response 200Hz - 10kHz ± 3dB

Distortion <1% THD @ 1 kHz

Noise <-50dBu

Table 19-4: Main Station: Loudspeaker amplifier

Page 231
Program line input and Four-wire option module inputs
Specification Description / value

Maximum level before 18dBu


clipping

Nominal input level 0dBu (selectable)

Input impedance >= 10KΩ

The following specified for a route to 4-wire output @ 0dBu out

Frequency response 20Hz - 10kHz ± 3dB

Distortion <0.2% THD @ 1kHz

Noise <-65dBu

Table 19-5: Main Station: Program line input and four-wire option module inputs

Four-wire module outputs


Specification Description / value

Maximum level before 18dBu


clipping

Nominal input level 0dBu (selectable)

Input impedance <= 100Ω

Table 19-6: Main Station: Four-wire module outputs

Page 232
Stage Announce outputs
Specification Description / value

Maximum level before 18dBu


clipping

Nominal output level 0dBu (selectable)

Output impedance <= 100Ω

The following specified for a route from a dynamic headset

Frequency response 300Hz – 12kHz ± 3dB

Distortion <0.1% THD @ 1kHz

Noise <-55dBu

Table 19-7: Main Station: Stage Announce outputs

Hot Mic output


Specification Description / value

Maximum level before 12dBu


clipping

Nominal output level 0dBu (selectable)

Output impedance <= 100Ω

The following specified for a route from a dynamic headset

Frequency response 300Hz - 12kHz ± 2dB

Distortion <0.2% THD @ 1kHz

Noise <-55dBu

Table 19-8: Main Station: Hot Mic output

Page 233
Helix Digital Partyline
Specification Description / value

Maximum level before 6dBu


clipping

Nominal input level -18dBu (C-C) -12dBu (RTS)

Input impedance >= 10KΩ bridging

The following specified for a circuit to a 4-wire output @0dBu in:

Frequency response 100Hz - 10 kHz ± 3dB

Distortion <0.2% THD @ 1kHz

Noise <-55dBu

The following specified for a circuit from a 2-wire input @0dBu out:

Frequency response 40Hz - 10kHz ± 3dB

Distortion <0.2% THD @ 1kHz

Noise <-55dBu

Auto-nulling and echo Yes


cancellation

RTS / Clear-Com selectable Yes

Termination External

Power 30V external

Table 19-9: Main Station: Partyline

Ethernet
Specification Description / value

Fast Ethernet standard 100BaseT only, Auto MDIX

Table 19-10: Main Station: Ethernet

Page 234
Mains power
Specification Description / value

Input Voltage range 100 – 240VAC

Input frequency range 50 – 60Hz

Input power <=250W

Powerline Intercom Output 59VDC ± 1V


Voltage

Output current per channel 1.5A (continuous)

Table 19-11: Main Station: Mains power

Environmental
Specification Description / value

Temperature 0˚C - 40˚C (32˚F - 104˚F)

Humidity 0 - 90% relative humidity

Table 19-12: Main Station: Environmental

Dimensions and weight


Specification Description / value

Dimensions 19in.W x 1.75in.H x ? in. D (483 mm x 44 mm


x ? mm)

Weight 5.83lbs. (2.65kg)

Table 19-13: Main Station: Dimensions and weight

Networking Specifications for Linked Main Stations


Specification Value
Latency on Powerline 40-80ms (Depends on cable type and length, and
how many devices are connected. The greater the
number of devices, the greater the latency.)
Latency over IP Network 30ms + Network Latency (Main Station to Main
Station)

Page 235
Bandwidth used 300 kbps per active Talker, for a maximum of 1
talker per device in the system
Each Beltpack and Speaker Station counts as 1
device
Each Main Station and Remote Station counts as 2
devices
IP version IPv4
Table 19-14 Networking specifications

19.2 Two-wire module (HLI-2W2)


Connectors
Specification Description / value

Intercom line (2) 3-Pin XLR-F

Table 19-15: two-wire module: Connectors

Dimensions and weight


Specification Description / value

Dimensions 7.05 in. H x 2.24 in. W x 1.54 in. D (179 x 57


x39 mm)

Weight 13 oz. (0.35 kg)

Table 19-16: Two-wire module: Dimensions and weight

Power requirements (external)


Specification Description / value

Per channel 0.025mA/channel

DC Voltage range 20 – 30 Volts

Table 19-17: Two-wire module: Power requirements

Environmental
Specification Description / value

Temperature 0˚C - 40˚C (32˚F - 104˚F)


Page 236
Humidity 0 - 90% relative humidity

Table 19-18: Two-wire module: Environmental

19.3 Four-wire module (HLI-4W2)


Connectors
Specification Description / value

Intercom line (2) RJ-45 (Ethercon)

Table 19-19: Four-wire module: Connectors

Dimensions and weight


Specification Description / value

Dimensions 7.05 in. H x 2.24 in. W x 1.54 in. D (179 x 57


x39 mm)

Weight 13 oz. (0.35 kg)

Table 19-20: four-wire module: Dimensions and weight

Environmental
Specification Description / value

Temperature 0˚C - 40˚C (32˚F - 104˚F)

Humidity 0 - 90% relative humidity

Table 19-21: four-wire module: Environmental

19.4 Remote Station (HRM-4X)


Connectors
Specification Description / value

Intercom Powerline Outputs Four 3-pin XLR. Two male and two female.

Headset 4-pin XLR–M

USB USB Type A

Page 237
Specification Description / value

Program 3-pin XLR–F

SA (Stage Announce) 3-pin XLR–M

Hot Mic / IFB Interface 1/4 in. (0.64 cm) phone jack

Control input/output 9-pin D-type

Table 19-22: Remote Station: Connectors

Microphone pre-amplifier
Specification Description / value

Headset Mic impedance: 200 Ω (Dynamic)

Headset Mic Voltage 1.7V (Electret selectable)

Limiter +23 dB

The following specified for a route to 4-wire output @ 0dBu out

Mic gain 60dB (dynamic) 45dB (electret)

Frequency response 300 Hz – 10 kHz + / -3dB (contoured for


intelligibility)

Distortion <0.2% THD @ 1 kHz

Noise- <-55dBu dynamic, <-65dBu electret

Table 19-23: Remote Station: Microphone pre-amplifier

Headphone amplifier
Specification Description / value

Load impedance 32 Ω

Output level +12dBu before clipping

Sidetone -12dB (selectable)

The following specified for a route from a 4-wire input @ 0dBu in

Max gain 0dB

Page 238
Specification Description / value

Frequency response 40 Hz - 10 kHz ±3dB

Distortion <0.1% THD @ 1 kHz

Noise <-65dBu

Headphone limiter 0dBu (selectable)

Table 19-24: Remote Station: Headphone amplifier

Loudspeaker amplifier
Specification Description / value

Load impedance 8Ω

Output level +18dBu before clipping

Max gain 18dB

The following specified for a route from a 4-wire input @ 0dBu in

Frequency response 200 Hz - 10 kHz ±3dB

Distortion <1% THD @ 1 kHz

Noise <-50dBu

Table 19-25: Remote Station: Loudspeaker amplifier

Page 239
Program line input and four-wire option module inputs
Specification Description / value

Maximum level before 18 dBu


clipping

Nominal input level 0dBu(selectable)

Input impedance >= 10 KΩ

The following specified for a route to 4-wire output @ 0dBu out

Frequency response 20 Hz - 10 kHz ±3dB

Distortion <0.2% THD @ 1 kHz

Noise <-65dBu

Table 19-26: Remote Station: Program line input and four-wire option module
inputs

Four-wire module outputs


Specification Description / value

Maximum level before 18 dBu


clipping

Nominal input level 0 dBu(selectable)

Input impedance <= 100Ω

Table 19-27: Remote Station: Four-wire module outputs

Page 240
Stage Announce outputs
Specification Description / value

Maximum level before 18 dBu


clipping

Nominal output level 0dBu(selectable)

Output impedance <= 100Ω

The following specified for a route from a dynamic headset

Frequency response 300Hz – 12kHz ±3dB

Distortion <0.1% THD @ 1kHz

Noise <-55dBu

Table 19-28: Remote Station: Stage Announce outputs

Hot Mic output


Specification Description / value

Maximum level before 12 dBu


clipping

Nominal output level 0dBu(selectable)

Output impedance <= 100Ω

The following specified for a route from a dynamic headset

Frequency response 300 Hz - 12 kHz ±2dB

Distortion <0.2% THD @ 1 kHz

Noise <-55dBu

Table 19-29: Remote Station: Hot Mic output

Page 241
Helix Digital Partyline
Specification Description / value

Maximum level before 6 dBu


clipping

Nominal input level -18dBu (C-C) -12dBu (RTS)

Input impedance >= 10KΩ bridging

The following specified for a circuit to a 4-wire output @0dBu in:

Frequency response 100Hz - 10 kHz ±3dB

Distortion <0.2% THD @ 1 kHz

Noise <-55dBu

The following specified for a circuit from a 2-wire input @0dBu out:

Frequency response 40 Hz - 10 kHz ±3dB

Distortion <0.2% THD @ 1 kHz

Noise <-55dBu

Auto-nulling and echo Yes


cancellation

RTS / Clear-Com selectable Yes

Termination External

Power 30V external

Table 19-30: Remote Station: Partyline

Ethernet
Specification Description / value

Fast Ethernet standard 100BaseT only, Auto MDIX

Table 19-31: Remote Station: Ethernet

Page 242
Mains power
Specification Description / value

Input Voltage range 100 – 240 VAC

Input frequency range 50 – 60 Hz

Input power <=250W

Powerline Intercom Output 59VDC ± 1V


Voltage

Output current per channel 1.5A (continuous)

Table 19-32: Remote Station: Mains power

Environmental
Specification Description / value

Temperature 0˚C - 40˚C (32˚F - 104˚F)

Humidity 0 - 90% relative humidity

Table 19-33: Remote Station: Environmental

Dimensions and weight


Specification Description / value

Dimensions 19 in. W x 1.75 in. H x ? in. D (483 mm x 44


mm x ? mm)

Weight 5.83 lbs. (2.65 kg)

Table 19-34: Remote Station: Dimensions and weight

19.5 Speaker Station (HKB-4X)


Connectors
Specification Description / value

Intercom line Two 3-pin XLR. One male and one female.

Page 243
Specification Description / value

Headset 4-pin XLR–M

Table 19-35: Speaker Station: Connectors

Microphone pre-amplifier
Specification Description / value

Headset Mic impedance: 200 Ω (Dynamic)

Headset Mic Voltage 1.7V (Electret selectable)

Limiter +23 dB

The following specified for a route to 4-wire output @ 0dBu out:

Mic gain 60dB (dynamic) 45dB (electret)

Frequency response 300 Hz – 10 kHz + / -3dB (contoured for


intelligibility)

Distortion <0.2% THD @ 1 kHz

Noise- <-55dBu dynamic, <-65dBu electret

Table 19-36: Speaker Station: Microphone pre-amplifier

Page 244
Headphone amplifier
Specification Description / value

Load impedance >32 Ω

Output level +12dBu before clipping

Sidetone -12dB (selectable)

The following specified for a route from a 4-wire input @0dBu in:

Max gain 0dB

Frequency response 40 Hz - 10 kHz ±3dB

Distortion <0.1% THD @ 1 kHz

Noise <-65dBu (@ max gain)

Headphone limiter -0dBu (selectable)

Table 19-37: Speaker Station: Headphone amplifier

Ethernet
Specification Description / value

Fast Ethernet standard 100BaseT only, Auto MDIX

Table 19-38: Speaker Station: Ethernet

Power requirements
Specification Description / value

Power requirements 4W

DC Voltage range 30 – 60 Volts

Table 19-39: Speaker Station: Power requirements

Page 245
Environmental
Specification Description / value

Temperature 0˚C - 40˚C (32˚F - 104˚F)

Humidity 0 - 90% relative humidity

Table 19-40: Speaker Station: Environmental

19.6 Beltpack (HBP-2X)


Connectors
Specification Description / value

Intercom line Two 3-pin XLR. One male and one female.

Headset 4-pin XLR–M and 2.5mm TRS jack

USB Micro-AB

TRS Headset 3.5mm mini jack

Table 19-41: Beltpack: Connectors

Microphone pre-amplifier
Specification Description / value

Headset Mic impedance: 200 Ω (Dynamic)

Headset Mic Voltage 1.7V (Electret selectable)

Limiter +23 dB

The following specified for a route to 4-wire output @ 0dBu out:

Mic gain 60dB (dynamic) 45dB (electret)

Frequency response 300 Hz – 10 kHz + / -3dB (contoured for


intelligibility)

Distortion <0.2% THD @ 1 kHz

Noise- <-55dBu dynamic, <-65dBu electret

Table 19-42: Beltpack: Microphone pre-amplifier


Page 246
Headphone amplifier
Specification Description / value

Load impedance >32 Ω

Output level +12dBu before clipping

Sidetone -12dB (selectable)

The following specified for a route from a 4-wire input @0dBu in:

Max gain 0dB

Frequency response 40 Hz - 10 kHz ±3dB

Distortion <0.1% THD @ 1 kHz

Noise <-65dBu (@ max gain)

Headphone limiter -0dBu (selectable)

Table 19-43: Beltpack: Headphone amplifier

Power requirements
Specification Description / value

Power requirements 4W

DC Voltage range 30 – 60 Volts

Table 19-44: Beltpack: Power requirements

Environmental
Specification Description / value

Temperature 0˚C - 40˚C (32˚F - 104˚F)

Humidity 0 - 90% relative humidity

Table 19-45: Beltpack: Environmental

Page 247
20 Glossary
Channel Any audio routed through the HelixNet system must be
configured into a Channel. Channels operate as virtual
partylines, which means that audio sources assigned to a
Channel will be able to talk and listen to all other sources
assigned to that Channel. In order for an audio source on one
device to talk to an audio source on another device, the two
Keysets must be brought together into one Channel.

Many audio sources in one Channel will not have a negative


effect on audio quality or latency.

Daisy-chaining Devices are daisy-chained when they are linked together by


cable in a line, as in a daisy chain. Other linking topologies
are available, such as a star or tree. In HelixNet, it is possible
to daisy chain Remote Stations, Speaker Stations and
beltpacks to the Main Station using a powerline that
transmits both data and power. However, the number and
type of devices linked will have an effect on the powerline. 10
beltpacks can be linked (powerlined), but if a Remote Station
is added into the line, the total number of devices possible in
the chain will go down due to the higher power requirement
of the Remote station. See 17 Linking Remote Stations
and Speaker Stations
You can find the URL to a powerline/distance calculator at the
beginning of Chapter 3. Installing HelixNet Partyline

Expansion In an Expansion Group, Main Stations and Remote Stations


Group (up to 3) are linked over IP in a host/slave relationship. This
means that the audio on all of the stations is controlled from
the host station, using one headset and speaker, creating a
convenient and easy to use set-up.
Expansion Groups must be established from the front panel
menus on the device(s).
See 5.9 Setting up a key Expansion Group

Page 248
KeySet A Keyset is a HelixNet unit that consists of an audio source or
Channel and a set of controls associated with that Channel.
The associated controls are: a menu screen, a rotary control,
a Talk button and a Call button. Main Stations and Remote
Stations have 4 Keysets, which can be seen on the front
panel of the device. Speaker Stations also have 4 Keysets,
though only 2 are visible on the device, the 4 Keysets
operate in a split screen. Beltpacks have 2 Keysets.
See 2.1.1 Main Station/Remote channel keyset and
display

Linking/ Only Main Stations can be linked.


Link Group Linking Main Stations in HelixNet allows more beltpacks to be
used and increases intercom range as far as your LAN will
allow. The linked Main Stations create a mesh connectivity,
which ensures robust audio transmission.
When Linking Main Stations in HelixNet 3.0 and above,
Channels with the same number (1 – 24) are merged.
Devices can be linked either from the unit front menus or
from the browser based Core Configuration Manager (CCM).
When linked in the CCM, devices and Roles can be configured
by proxy from any Main Station in the Link Group.
See 15 Linking in the Core Configuration Manager
(CCM) and 16 Linking Main Stations (cabling and
linking from device menus) for more information.

Pairing Remote or Speaker Stations are connected to the Main


Station over LAN/IP. This allows Main Station Channels to be
available to a remote connection, either an HRM (Remote
Station) or an HKB (Speaker Station). Pairing over IP will
provide better latency than connecting with a powerline.
See 17.1.2 Ethernet point-to-point link

Page 249
Role A Role is a pre-set configuration that includes Channel
assignment, audio settings, IFBs, relays etc. Each HelixNet
device has a default Role that can be used as it is or modified
to fit requirements. Each Role can be given a name (a label)
that corresponds to a common user workflow, such as
producer, director, A1, etc.
When adding new Roles, you will modify an existing
template, using either the default Role for that device, or
another Role that you have already made. Default Roles can
be modified but not deleted or loaded to devices, you will
always work with a copy. Default Roles can be returned to
factory settings if required.
To use Roles you must have HelixNet 3.0 or above installed
on your Main Stations.
See 12 Roles for more information.

Page 250
21 Menu maps
HMS-4X Main Station menu map
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last )
Audio Settings Headset Sidetone Gain Range: 0dB to -18dB
Default: -12db
Headphone Limit Range: +6dB to -6dB
Default: 0db
Sidetone Control Tracking
Non-Tracking
Disabled
Default: Tracking
HS Mic Type Electret
Dynamic (0 dB)
Dynamic (-10 dB)
Default: Dynamic (0 dB)
Microphone Headroom Normal
High
Default: Normal
Contour Filter Enabled
Disabled
Default: Enabled

Program Input Label 12 characters

Gain Range: +12dB to -12dB


Default: 0db

Page 251
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last )
GPO Trigger Enabled
Disabled
Default: Enabled
VOX Enabled
Disabled
Default: Disabled
VOX Off Delay Range: 0.5 – 4 sec
Default: 0.5 sec

Program IFB IFB Dim Level IFB Disabled + Range: -6dB - -24dB + Full
Cut
SA Output Gain Range: +12dB to -12dB
Default: 0db
Hot Mic Output

Front Panel Loudspeaker Dim Range: 0dB to -24dB


Default: -6dB
Station Settings Preferences Roles
Select Role or Local Config

Station ID
Alphanumeric entry

Keyset Assign Keyset 1 – 4 None


Channel 1 – 12 (or 24)

Keysets Talk #1 Latch

Talk #2 Latch Latching


Non-Latching
Default: Latching
Talk #3 Latch

Page 252
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last )
Talk #4 Latch

SA Output Key Latching


Non-Latching
Default: Non-latching
All Talk Toggle All Channels/Visible Channels
Default All Channels
RMK Disabled
All Channels
Visible Channels
Default: Enabled All Channels
Display OLED Brightness High
Medium
Low
Default: Medium
Key Brightness High / Low
High / Off
Low / Off
Off / Off
Default: High / Low
Screensaver Enabled
Disabled
Default: Enabled
Channels Channel 1 Label Press to Edit
Max. length for labels = 10 characters
Channel 2
Channel 3
Program Listen None
Channel 4 List of programs
[…] Default: None
GPO on Talk Default: None
Relay 1 - 4
GPO on Call Default: None

Page 253
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last )
Relay 1 - 4

Control I/O Inputs Opto 1 None


Call Key 1
Opto 2
Talk Key 1
Opto 3 Call Key 2
Opto 4 Talk Key 2
Call Key 3
Outputs Relay 1 Talk Key 3
Relay 2 Call Key 4
Talk Key 4
Relay 3
Default: None
Relay 4

Page 254
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last )
Module Settings Slot n /Port Channel Assign Disabled
Channel A
A/B 4W
Channel B
Channel C
Channel D
Default: Disabled
Program Output Unmute
Mute
Default: Mute

GPO Trigger Enabled


Disabled
Default: Enabled

Input Gain Range: +12dB to -12dB


Output Gain Default: 0db

VOX Enabled
Disabled
Default: Disabled
VOX Off Delay Range: [0].5 – 4 secs
Default: [0].5 secs
Slot n /Port Channel Assign Disabled
A/B 2W Channel A
Channel B
Channel C
Channel D
Default: Disabled
Program Output Unmute
Mute
Default: Unmute

Page 255
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last )
Auto-Nulling Start

Mode Clear-Com
RTS Audio Pin 2
RTS Audio Pin 3
Default: Clear-Com
GPO Trigger Enabled
Disabled
Default: Enabled
Input Gain Range: -3dB to +3dB
Output Gain Default: 0db
RMK Input Enabled
RMK Output Disabled
Default: Enabled
VOX Enabled
Disabled
Default: Disabled
VOX Off Delay Range: [0].5 – 4 secs
Default: [0].5 secs
Network Stations Preferences Hostname (12 chars)
DHCP enabled/disabled
IP address (enter IP address)
Subnet mask
Gateway
[Station IDs} (info only)
Hostname
Linked status
IP address
Linking Link mode Disabled
Link Master
Link Member

Page 256
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last )
Link to Master By name
By IP address

Expansion Host Enabled


Mode Expand to host Disabled (default)

Administration Software Current MS Version


IVR Version
Snx Version where n is slot number and x is
the port
Update None or version list
Beltpacks Menu Lock Unlock All
Lock All
Reset Reset to Default Reset HMS
Reset Devices
Reset All
Reboot Reboot Now

Settings Save USB drive or file list


Restore local USB drive or file list
Restore system USB drive or file list

Diagnostics Hardware Main PCB Part: [Part_Number]


Revision: [Revision]
Slot 1 PCB
Serial number: [Serial number]
Slot 2 PCB
Slot 3 PCB
Temperature Sensor 1 Temperature in °C.
Sensor 2 Note:
Single fan on if any sensor > 60°C.
Sensor 3

Page 257
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last )
Double fan on if any sensor > 65°C.
Double fan off if < 55°C / single fan off if <
50°C.
Powerlines Powerline 1 Status: [OK or BUSY (according to responses
to MME requests)].
Powerline 2 DMC:[MAC of powerline modem]
HMC: [MAC of local blackfin processor]
Beltpacks: [# of beltpacks detected by
powerline modem]
Collision rate: [Percentage (0% when
operating normally)]
Error rate: [Percentage (0% when operating
normally)]
Volts: [Voltage]
Keysets Keyset 1 Name: Channel name
Keyset 2 Talkers: Number of talkers on party line
Keyset 3 Devices: Number of beltpacks listening on
party line
Keyset 4
Main Stations: Number of Main Stations
listening
2-Wire: Number of 2-Wire ports listening
4-Wire: Number of 4-Wire ports listening

Page 258
HRS-4X Remote Station menu map

Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last )


Audio Settings Headset Sidetone Gain Range: 0dB to -18dB
Default: -12db
Headphone Limit Off + Range: +6dB to -6dB
Default: 0db
Sidetone Control Tracking
Non-Tracking
Disabled
Default: Tracking
HS Mic Type Electret
Dynamic (0 dB)
Dynamic (-10 dB)
Default: Dynamic (0 dB)
Microphone Headroom Normal
High
Default: Normal
Contour Filter Enabled
Disabled
Default: Enabled

Program Input Gain Range: +12dB to -12dB


Default: 0db

IFB Dim Level Range: --6dB to -24dB


Default: Off
GPO Trigger Enabled
Disabled
Default: Enabled
VOX Enabled
Disabled

Page 259
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last )
Default: Disabled
VOX Off Delay Range: 0.5 - 4sec
Default: 0.5sec
SA Output Mode Channel Assigned
SA
Default: Channel Assigned
Gain Range: +12 to -12dB
Default: 0dB
Program Output Unmute
Mute
Default: Mute
Channel Assign Disabled
Channel A
Channel B
Channel C
Channel D
Default: Disabled
Hot Mic Output Gain Range: +12 to -12dB
Default: 0dB
Front Panel Loudspeaker Dim Range: 0dB to -24dB
Default: -6dB

Page 260
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last )
Station Settings Preferences Roles Default: HRM – [unique ID
Select Role or Local Config]

Keyset Assign Keyset 1 – 4


Channel 1 – 12 (or 24)

Keysets Talk 1 - 4 Latching


Non-Latching
Default: Latching
All Talk All Channels
Visible Channels

SA Output Key Latching


Non-Latching
Default: Non-latching
RMK Enabled
Disabled
Default: Enabled
Display OLED Brightness High
Medium
Low
Default: Medium
Key Brightness High / Low
High / Off
Low / Off
Off / Off
Default: High / Low
Screensaver Enabled
Disabled
Default: Enabled
Channels Channel 1 Label Press to Edit
Max. length for labels = 10 characters
Channel 2
Channel 3 Program Listen None
List of programs

Page 261
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last )
Channel 4 Default: None
[…] GPO on Talk Default: None
Relay 1 - 4
GPO on Call Default: None
Relay 1 - 4

Page 262
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last )
Control I/O Inputs Opto 1 None
Call Key 1
Outputs Relay 1 Talk Key 1
Call Key 2
Talk Key 2
Call Key 3
Talk Key 3
Call Key 4
Talk Key 4
Default: None
Network Preferences Hostname (12 char)
DHCP enabled/disabled
IP address (enter if required)
Subnet mask
Gateway
Pair to Station By Name Enabled
By Address Disabled
Default: Enabled

Expansion mode Host (enabled/disabled)


Expand to host (none/hostname)
Administration Software Current HelixNet System Version
Remote Station Version
Update None or version list
Reset Reset to Default Reset Now

Reboot Reboot Now

Settings Save USB drive or local


Restore local USB drive or file list
Diagnostics Main PCB

Page 263
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last )
Powerlines Powerline 1 Status: [status]
DMC: {MAC]
HMC: [MAC]
MMC: [MAC]
Rx rate: [Mbps]
Tx rate: [Mbps]

Network Status IP Address

IP Address

IP Mask
Mac
Keysets Keyset 1 Name: Channel name
Keyset 2 Talkers: Number of talkers on party line
Keyset 3 Devices: Number of beltpacks listening on party
line
Keyset 4
Main Stations: Number of Main Stations listening
2-Wire: Number of 2-Wire ports listening
4-Wire: Number of 4-Wire ports listening

Page 264
HKB-4X Speaker Station menu map

Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last )


Roles Select Role or Local Config.

Audio Settings Headset Sidetone Gain Range: 0dB to -18dB

Default: -12db

Headphone Limit Off + Range: +6dB to -6dB

Default: 0db

Sidetone Control Tracking


Non-Tracking
Disabled

Default: Tracking

HS Mic Type Electret (-15dB)


Dynamic (0 dB)
Dynamic (-10 dB)

Default: Dynamic (0 dB)

Microphone Headroom Normal


High

Default: Normal

Contour Filter Enabled


Disabled

Default: Enabled

PGM/audio in Label (12 char)

Gain

IFB dim level


Page 265
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last )
GPO trigger

Vox

Vox off delay

SA/audio out Mode (toggle Channel assign/SA)

Gain

Program Output (mute/unmute)

Channel assign (1 – 24)

Hot mic output Gain

Front Panel Loudspeaker Dim Range: 0dB to --24dB

Default: -6db

Station Settings Keyset Assign Keyset 1 – 4


Channel 1 – 12 (or 24 depending on license)

Keysets Talk 1 - 4

Latching
SA out key (latch/non latch) Non-Latching

Default: Latching
All Talk (All Channels (up to
24)/Visible Channels (4))

Page 266
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last )
RMK (All Channels (up to 24)/Visible
Channels (4))

Display OLED Brightness High


Medium
Low

Default: Medium

Key Brightness High / Low


High / Off
Low / Off
Off / Off

Default: High / Low

Screensaver Enabled
Disabled

Default: Enabled

Network Pair to Station By Name Separate


By Address IP address: xx.xx.xx.xx where x is a numeric
value

Preferences DHCP Enabled


Disabled

Default: Enabled

IP Address IP address: xx.xx.xx.xx where x is a numeric


value

Gateway IP address: xx.xx.xx.xx where x is a numeric


value

Page 267
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last )
Subnet Mask IP address: xx.xx.xx.xx where x is a numeric
value

Administration Software Current HelixNet

Speaker Station

License Current/Enter code

Reset Reset to Default Reset Now

Reboot Reboot Now

Setting Save/restore

Diagnostics Powerlines Powerline 1 Status: [OK or BUSY (according to responses to


MME requests)].
DMC:[MAC of powerline modem]
HMC: [MAC of local blackfin processor
Rx rate:[Mbps]
Tx rate:[Mbps]
Status:[status]
IP Addr [IP Address]
IP Mask [Subnet Mask]
MAC:[MAC Address]

Networking Ethernet

Keysets Keyset 1 Name: Channel name


Talkers: Number of talkers on party line
Keyset 2
Devices: Number of beltpacks listening on party
Keyset 3 line
Main Stations: Number of Main Stations listening
Keyset 4
2-Wire: Number of 2-Wire ports listening
4-Wire: Number of 4-Wire ports listening

Page 268
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last )
Hardware

Voice clients

Page 269
HBP-2X Beltpack menu map
Menu 1 (First) > Menu 2> Menu 3 (Last )

Roles Select Role or Local Config

Audio Settings Sidetone Gain Range: 0dB to -18dB

Default: -12dB

Headphone Limit Off + Range: +6 to -12dB

Default: 0dB

Sidetone Control Tracking


Non-tracking
Disabled

Default: Tracking

HS Mic Type Electret (-15dB)


Dynamic (0dB)
Dynamic (-10dB)

Default: Dynamic (0dB)

Note:
Electret = 35dB fixed gain, non-user adjustable.
Dynamic = 50dB fixed gain, non-user adjustable.

Headroom Normal
High

Default: Normal

Contour Filter Enabled


Disabled

Page 270
Menu 1 (First) > Menu 2> Menu 3 (Last )

Default: Enabled

Beltpack Settings Left Channel None


Channel assign (1 – 24)
Right Channel
Talk (latch/non latch)

Default: Latch

USB flasher (disabled/blinking/solid)

Default: disabled

Vibrate On Call On
Off

Default: Off

Display Settings OLED Brightness High


Medium
Low

Default: Medium

Key Brightness High / Low


High / Off
Low / Off
Off / Off

Default: High / Low

Rotate Display Enabled


Disabled

Default: Disabled

Page 271
Menu 1 (First) > Menu 2> Menu 3 (Last )

Screensaver Channel

Hostname

Role (default)

Blank

Disabled

Network IP Address IP address: xx.xx.xx.xx where x is a numeric


value

Administration Software Version npl-1.0.x, uboot

Software Update npl-1.0.x

Reset to Default Reset Now

Hardware Main PCB

Important Note:
There are 4 levels of Menu for Hardware

Diagnostics Powerline Status: [OK or BUSY Part: [Part_Number]


(according to Revision: [Revision]
Note:
responses to MME Serial number: [Serial
Line (partyline) that connects beltpack to
requests)]. number]
the network (and which also powers the
DMC:[MAC of
beltpack).
powerline modem]
HMC: [MAC of local
blackfin processor]
MMC: [MAC of the
Main Station

Page 272
Menu 1 (First) > Menu 2> Menu 3 (Last )

powerline modem,
to which the
beltpack is
connected]
Rx rate: Range:
140 – 150 Mbps
Tx rate: Range: 140
– 150 Mbps

Keysets 1 to 4 Name: Channel name


Talkers: Number of talkers on party line
Beltpacks: Number of beltpacks listening on party
line
Main Stations: Number of Main Stations listening
2-Wire: Number of 2-Wire ports listening
4-Wire: Number of 4-Wire ports listening

Table 21-1: HBP-2X Beltpack

Page 273
22 Menu trees
This chapter provides tree diagrams of the menu structure of all the HelixNet
devices. Use these diagrams to gain a quick overview of what menu options are
available, and where to find them.
Note: Items marked with an asterisk (*) are not present in expansion mode.

Page 274
Table 22-1 Main Station menu tree
Headset* Sidetone Gain Adjust Level

Microphone* Headphone Limit Adjust Level

Main Program Input Headphone Gain Adjust Level

Station
Tracking/Non-tracking/
Program IFB Sidetone Control
Disabled

front
SA Output* HS Mic Type Electret/Dynamic

Hot Mic Output*

menu Front Panel*


Headroom Toggle Normal/High

Toggle Enable/Disable
screens
Contour Filter

Preferences Roles Select Local Config or Role


Label Enter 12 character label
Keyset Assign Keyset 1 to 4 Up to 24 Channels
Gain Adjust Level
Keysets
Latching/Non-Latching/
Talk 1 to 4 GPO Trigger Toggle GPO Trigger
Display* Disabled
Toggle Latching/Non-
SA Out Key VOX Toggle VOX
Latching
Toggle All Channels/
All Talk VOX Off Delay Adjust Level
Visible Channels
All Channels/Visible
RMK
Channels/Disabled
IFB Dim Level Adjust Level
OLED Brightness High/Medium/Low
Audio Settings High/Low, High/Off, Low/ Gain Adjust Level
Key Brightness
Off, Off/Off
Station Settings
Channel 1 to 24 Screensaver Toggle Enabled/Disabled Gain Adjust Level
Channels
Control I/O Inputs Loudspeaker Dim Adjust Level
Label Enter 12 character label
Outputs
Module Settings Slot n/Port A/B 4W
Program Listen None/Programs Disabled/Channel 1
Channel Assign
Networking Slot n/Port A/B 2W to 24
GPO on Talk None/Relay 1 to 4
Program Output Toggle Unmute/Mute
Administration Slot n Ethernet
GPO on Call None/Relay 1 to 4
Input Gain Adjust Level
Diagnostics Slot n Fiber
Output Gain Adjust Level
Opto 1 to 4 None/Call or Talk 1 to 4 Slot n
Toggle Enabled/
None/Call or Talk 1 to 4/ GPO Trigger
Relay 1 to 4/SA Disabled
SA Empty Toggle Enabled/
VOX
Disabled

Enter 12 character VOX Off Delay Adjust Level


Preferences Hostname
label
Hardware Toggle Enabled/ Disabled/channel 1 to
Software Stations DHCP Channel Assign
Current Disabled 24
Hardware Main PCB Linking IP Address Enter IPv4 Address Program Output Toggle Unmute/Mute
License Update
Temperature Slot 1 PCB Link To Master Subnet Mask Enter IPv4 Address Auto Nulling Start
Reset
Powerlines Slot 2 PCB Current Clear-Com/RTS Audio
Settings Expansion Mode Gateway Enter IPv4 Address Mode
Pin 2/RTS Audio Pin 3
Keysets Slot 3 PCB Enter Code
Input Gain Adjust Level
Station IDs
Sensor 1 System ID Output Gain Adjust Level
Reset To Default Disabled/Master/
No. of Channels (12 Link Mode Toggle Enabled/
Sensor 2 or 24) Member GPO Trigger
Reboot Disabled
Toggle Enabled/
Sensor 3 By Name None/Station IDs RMK Input
Disabled
Toggle Enabled/
Save By Address Enter IPv4 Address RMK Output
Powerline 1/2 Disabled
Toggle Enabled/
Restore VOX
Toggle Enabled/ Disabled
Keyset 1 to 4 Host/Expand to Host
Disabled VOX Off Delay Adjust Level

Page 275
Table 22-2 Remote Station menu tree
Headset Sidetone Gain Adjust Level

Microphone Headphone Limit Adjust Level

Remote PGM/Audio in Headphone Gain Adjust Level


Tracking/Non-tracking/

Station
SA/Audio out Sidetone Control
Disabled
Hot Mic Output HS Mic Type Electret/Dynamic

front Front Panel


Headroom Toggle Normal/High

screens Contour Filter Toggle Enable/Disable

menu Label Enter 12 character label

Keyset Assign Keyset 1 to 4 Up to 24 Channels Gain Adjust Level

Keysets IFB Dim Level Adjust Level


Latching/Non-Latching/
Talk 1 to 4
Display Disabled GPO Trigger Toggle GPO Trigger
Toggle Latching/Non-
SA Out Key
Latching VOX Adjust Level
Select Local Config or Role Toggle All Channels/
All Talk
Visible Channels VOX Off Delay Adjust Level
All Channels/Visible
OPT (RMK)
Channels/Disabled
Mode Toggle Channel Assign/SA
Role
OLED Brightness High/Medium/Low Gain Adjust Level
Audio Settings High/Low, High/Off, Low/
Key Brightness Program Output Toggle Unmute/Mute
Off, Off/Off
Station Settings
Channel 1 to 24 Screensaver Toggle Enabled/Disabled Channel Assign Select channel 1 to 24
Channels
Control I/O Inputs Gain Adjust Level
Label Enter 12 character label
Outputs
Networking Loudspeaker Dim Adjust Level
Program Listen None/Programs
Administration
GPO on Talk None/Relay 1 to 4
Diagnostics
GPO on Call None/Relay 1 to 4

Opto 1 None/Call or Talk 1 to 4

Relay 1 None/Call or Talk 1 to 4

Preferences
Hostname
Pair to Station Enter 12 character
Software Current DHCP label
Update Expansion Mode Toggle Enabled/
Reset IP Address Disabled
Settings Subnet Mask Enter IPv4 Address
Hardware Main PCB Reset To Default
Gateway Enter IPv4 Address
Powerlines Powerline Reboot
Enter IPv4 Address
Networking Ethernet
Save By Name
Keysets Keyset 1 to 4 None/Station IDs
Restore local By Address
Enter IPv4 Address

Toggle Enabled/
Host
Disabled
Toggle None/
Expand to Host
Hostname

Page 276
Table 22-3 Speaker Station menu tree

Speaker
Headset Sidetone Gain Adjust Level

Microphone Headphone Limit Adjust Level

Station Front Panel Headphone Gain Adjust Level

front
Tracking/Non-tracking/
Sidetone Control
Disabled

screens
HS Mic Type Electret/Dynamic

menu Headroom

Contour Filter
Toggle Normal/High

Toggle Enable/Disable

Loudspeaker Dim Adjust Level


Keyset Assign Keyset 1 to 4 Up to 24 Channels

Keysets
Latching/Non-Latching/
Talk 1 to 4 Disabled/Channel 1
Display Disabled Channel Assign
Toggle Latching/Non- Slot n/Port A/B 4W to 24
SA Out Key
Latching Program Output Toggle Unmute/Mute
Toggle All Channels/ Slot n/Port A/B 2W
All Talk
Visible Channels Input Gain Adjust Level
All Channels/Visible Slot n Ethernet
Select Local Config or Role RMK
Channels/Disabled Output Gain Adjust Level
Slot n Fiber
Toggle Enabled/
GPO Trigger
OLED Brightness High/Medium/Low Slot n Disabled
Toggle Enabled/
High/Low, High/Off, Low/ VOX
Key Brightness Empty Disabled
Off, Off/Off
Roles VOX Off Delay Adjust Level
Screensaver Toggle Enabled/Disabled
Audio Settings Disabled/channel 1 to
Channel Assign
24
Station Settings
Program Output Toggle Unmute/Mute
Module Settings
Auto Nulling Start
Networking Toggle Enabled/ Clear-Com/RTS Audio
Preferences DHCP Mode
Disabled Pin 2/RTS Audio Pin 3
Administration
Pair to Station IP Address Enter IPv4 Address Input Gain Adjust Level
Diagnostics Software Current
Subnet Mask Enter IPv4 Address Output Gain Adjust Level
License Update
Gateway Enter IPv4 Address Toggle Enabled/
GPO Trigger
Reset Disabled
Current Toggle Enabled/
RMK Input
Settings Disabled
Enter Code By Name None/Station IDs Toggle Enabled/
RMK Output
Disabled
By Address
Toggle Enabled/
Enter IPv4 Address VOX
Reset To Default Disabled
VOX Off Delay Adjust Level
Powerlines Reboot

Networking Ethernet
Save
Keysets 1-4
Restore
Hardware

Voice clients

Page 277
Table 22-4 Beltpack menu tree
Local Config
Beltpack Roles

Menu Sidetone Gain Adjust Level

screens Headphone Limit Adjust Level

Headphone Gain Adjust Level


Tracking/Non-tracking/
Sidetone Control
Disabled
HS Mic Type Electret/Dynamic

Mic Headroom Toggle Normal/High

Contour Filter Toggle Enable/Disable

None/Channel 1-24/
Left Keyset Channel Assign
Stacked key
Latching/Non
Right keyset Talk
Latching/Disabled
Disabled/Blinking/
Vibrate On Call On/Off USB Flasher
Solid

Roles
Screensave Channel
Audio Settings Hostname
Role
Beltpack Settings Blank
Disabled
Display Settings
Network IP address

Administration
View hostname
Diagnostics Software version
Software version
Reset to default Reset Now

Hardware PCB

Powerline Powerline

Keysets Keyset 1 - 2 View only


Name (of Channel)
Talkers
Devices
Main Station
2-wire
4-wire

Page 278
23 Cabling reference
You can connect HBP-2X Beltpacks using:
 A wide range of standard microphone (intercom) cable types (16 AWG –
26 AWG).
 CAT5, CAT5e and CAT6 cable types.
XLR cable CAT5/6 cable
Pin 1 Pin 1 and Pin 2 and shield/drain wire
Pin 2 Pin 3, Pin 5 and Pin 7
Pin 3 Pin 4, Pin 6 and Pin 8
Table 23-1 Recommended cabling scheme
Clear-Com recommends the following cable types:
 Belden 9207 for fixed installation
 Belden 9463F for portable installations
Note: Cat 5 screen should be connected to chassis at one end of cable only.
Note: Clear-Com recommends the use of shielded twisted pair cabling.
You can also mix CAT cables and microphone cables when connecting to the HMS-
4X Main Station. For example, you might use CAT cables to trunk long distances,
and flexible microphone cables to connect HBP-2X Beltpacks to bulkheads.
Note: The cabling information provided in this guide is for guidance only. For in-depth,
tailored advice on cabling, Clear-Com recommends that you contact your Clear-
Com representative.

23.1 Interoperability
The optional interface modules (two-wire, four-wire, 10/100BaseT Ethernet and
Fiber Channel) for the HMS-4X Main Station enable interoperability with your
existing communications infrastructure.
You can connect the HMS-4X Main Station to:
 Two-wire intercom systems and devices (including Encore and RTS)
using standard microphone cable (16 AWG – 26 AWG).
 Four-wire intercom systems and devices (including Eclipse) using
Ethernet (CAT) cable.
Tip: For more information about integrating HelixNet Partyline into your existing
communications infrastructure, see 18 Connecting to Other Intercom
Systems.

Page 279
23.2 Cable capacitance versus distance
Standard microphone cables impose distance limitations at their upper limits due
to cable capacitance.
If your priority is audio quality, experiment with attaching one or two fewer
devices to each line. Your choice of topology (daisy chain, star or tree) may also
impact audio quality over distance.

Manufacturer Cable type Gauge Style Attenuation


(AWG) / 100m

Belden 9463f 20 Std 16 dB

Belden 9207 20 Std 9 dB

Belden 1533P 24 Cat5e 11 dB

Table 23-2: Cable capacitance

Page 280
Quick reference: Cable capacity versus distance

Beltpack Limit Distances


20
18
16
14
Number of Units

12
10 9463f
8 9207
6 9451
4
2
0
0 200 400 600 800 1000
Limit Distance (meters)

Page 281
Remote Station Limit Distances
7

5
Number of Units

4
9463f
3
9207
2 9451

0
0 200 400 600 800 1000
Limit Distance (meters)

Page 282
Speaker Station Limit Distances
7

5
Number of Units

4
9463f
3
9207
2 9451

0
0 200 400 600 800 1000
Limit Distance (meters)

Note: The above graphs are intended as a general guide only. Actual cable performance may vary,
depending on the conditions and complexity of the installation.

Page 283
23.3 Cable connections
The diagrams on the following pages reference the following labels and notes.

Label Manufacturer Part Number Description

1 Clear-Com HMS-4X HelixNet Main Station

2 Belden 8760,9207 18 or 20 AWG twisted pair cable


Or terminated with 3-pin XLR
9463F

3 Middle Atlantic (or CH-1 1 RU shielded chassis


equivalent)

4 Neutrik (or NC3FD-L-B-1 3 pole female chassis mount


equivalent)

5 Neutrik (or NC3MD-L-B-1 3 pole male chassis mount


equivalent)

6 Neutrik (or NA3MDF 3 PIN XLR M-F FEED THRU


equivalent) ADAPTER

7 Belden (or existing 1351A or 1533P 24 AWG, shielded cat 6 cabling


cabling)

8 Belden 8760,9207 or XLR3 M-F patch cord


9463F
9 Belden 8760,9207 or 18 or 20 AWG twisted pair cable
9463F
Table 23-3 Label descriptions

Label Note
1 Wire in accordance with Table 23-5

2 Equipment rack, breakout box chassis and patch panel must be connected
to safety earth
3 Connect up to 32 wall plate locations to patch panel with individual CAT 5
cables
4 If multiple wall plates are co-located at a remote location, daisy chain
their wiring at the remote location and connect a single CAT 5 cable from
the remote location back to the patch panel
5 Use short length, high quality XLR patch cords with shielded connectors

6 Do not patch between separate power lines

7 Assemble item 6 to panel with male connectors to front

Page 284
Table 23-4 Notes

CAT5 XLR
1 1
2 1
3 2
4 3
5 3
6 2
7 2
8 3
Shield 1
Table 23-5 Wiring diagram

Page 285
1 5 4 3
10 Partylines

HELIXNET MAIN 5 8 Wall Plate


STATION 2 10 Partylines
2 Partylines 4 3 1 7

6 32 Partylines Wall Plate Wall Plate

5 4 3
10 Partylines

Wall Plate
5 8
10 Partylines
4 3 1 7
SCHEMATIC VIEW
6 Wall Plate Wall Plate
32 PL

Figure 23-1 Cabling schematic

Page 286
5 9 4 10 PL

6 7
F
XLR XLR 6

Wall Plate XLR XLR


M F M

Wall Plate Wall Plate XLR XLR

XLR

2
Figure 23-2 Cabling side view

Page 287
POWER LINE #1A

POWER LINE #1A


WALL PLATE

POWER LINE #1B

POWER LINE #1B


WALL PLATE
Figure 23-3 Front view

Page 288
24 Troubleshooting
Issue Solution

Why are the Talk keys Flashing Talk keys may indicate a fault in the
flashing periodically? cable.
Check the cable for short-circuit conditions and
replace if necessary.

The Call functionality on HelixNet Partyline operates at different voltage


my analog beltpack is no levels than analog two-wire partyline systems.
longer working.
The analog beltpack may have been damaged if
it was connected to a HelixNet Main Station
partyline port.
Contact Clear-Com for repair options.

I cannot pass audio to Two-wire option modules require an external


wired / wireless intercom power supply. See 18 Connecting to Other
equipment over the Two- Intercom Systems.
wire module.

Why do I hear an echo Run auto-nulling.


when interfacing via a
Ensure that all unused Talk keys in the system
two-wire audio port?
are unlatched.

Echo occurs even after Check to ensure all open Talk keys are not
Two wire module has latched and re-null.
been auto-nulled.

There is no audio or only Check the cable used to connect the equipment.
partial audio (send or
HelixNet to Eclipse four-wire connections only
receive, but not both)
require a standard CAT cable, whereas other
between other audio
four-wire connections (to Tempest™, CellCom /
systems / sources
FreeSpeak, and other systems) require an audio
connected over four-wire.
crossover cable. See:
 2.2.1 HMS-4X Main Station rear
panel: Interface modules
 18 Connecting to Other Intercom
Systems

Page 289
Line 1 (or Line 2) LED is There is a short-circuit somewhere on that
blinking red. Powerline. Unplug everything from that Powerline
and add cables and Beltpacks one at a time until
you find the short-circuit.

Line 1 (or Line 2) LED is There are digital errors or there is cross-talk on
steady red and one or that Powerline. Look at the Diagnostics-
more Beltpack has no bars >Powerlines->Powerline 1(or 2) page.
showing up for signal
If the number of Beltpacks showing there is
strength.
greater than what you physically connected to
that Powerline, cross-talk is happening between
the Powerlines. Make sure you are using properly
shielded Mic cables or Cat cables.
If the number of Beltpacks showing there does
match what you physically connected to that
Powerline and errors or high collision rate is
displayed, verify that you don’t exceed the
number of Beltpacks per Powerline or distance as
per the Cable capacity versus distance table.
High collision rate means communication issues
on the powerline. Possible causes are:
 Unshielded or bad cables
 Powerline 1 looped back into Powerline 2
(or from one HMS to another)
 Cables too long
 Too many cables in the infrastructure
(even unconnected strand count)
 Too many devices on the Powerline
 Faulty device
I inserted my USB drive Make sure that your USB drive is formatted with
with a ccb file on it and at least one partition. Make sure your .ccb file is
the Administration- in the root directory of the first partition on your
>Software->Update menu USB drive. If not you can run diskpart on
shows “None”. Windows Vista and later versions of Windows to
create a partition.

I upgraded to 1.1 but I Make sure you properly inserted an Ethernet or


cannot see the Fiber module in one of the option module slots.
Networking menu. You can verify that they are detected by looking
at the Modules Settings menu.

I powered up two Main Make sure your Ethernet of Fiber cable is


Stations and they are not properly connected to a router, a switch or
showing up in the another Main Station. There is a green LED

Page 290
Networking > Stations beside each Ethernet and Fiber port to indicate
list. that the connection is fine. Look at each station
IP address and Subnet Mask under Networking >
Preferences and make sure that they are part of
the same subnet. Also make sure that their IP
address is different from any other device on
your IP network.

My connection to the CCM This is generally caused by more than one device
is intermittent. using the same IP address. Check with your
network administrator that there is no IP clash.

My device has gone into If your device is set to Dynamic Host


link-local mode. (IP Configuration Protocol (DHCP) and there is no
address = 169.254.XX.XX) DHCP available on the network it is connected to
it will revert to link-local automatically. You need
to allocate a static IP address to this device. See
Chapter 4 for more information.

Table 24-1: Troubleshooting

Page 291
25 Compliance
FCC notice
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communication. Operation of this equipment in a residential area is likely to cause
harmful interference, in which case the user will be required to correct the
interference at his own expense.
Changes or modifications not expressly approved by Clear-Com, LLC, an HM
Electronics, Inc. company could void the user’s authority to operate this
equipment.
Industry Canada Compliance Statement
This Class[A] digital device complies with Canadian ICES-003.
Avis de conformité à la réglementation d'Industrie Canada
Cet appareil numérique de la class[*] est conforme à la norme NMB-003 du
Canada.
Korean notice
A급 기기 (업무용 방송통신기자재)
이 기기는 업무용(A급)으로 전자파적합기기로
서 판매자 또는 사용자는 이 점을 주의하시기
바라며, 가정외의 지역에서 사용하는 것을 목
적으로 합니다.
The HMS-4X, HRM-4X, HBP-2X, HBP-2XS, HLI-2W2 and HLI-4W2 products
comply with the following specifications:
EN55022 Emissions
EN55024 Immunity
Electromagnetic Compatibility Directive 2004/108/EC
Low Voltage Directive 2006/95/EC

Page 292
Warning:
This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
The HMS-4X, HLI-2W2 and HLI-4W2 products comply with the following
specifications:
UL 60065-7
CAN/CSA-C22.2 No.60065-3
IEC 60065-7
Waste Electrical And Electronic Equipment (WEEE)
The European Union (EU) WEEE Directive (2002/96/EC) places an obligation on
producers (manufacturers, distributors and/or retailers) to take-back electronic
products at the end of their useful life. The WEEE Directive covers most Clear-
Com products being sold into the EU as of August 13, 2005. Manufacturers,
distributors and retailers are obliged to finance the costs of recovery from
municipal collection points, reuse, and recycling of specified percentages per the
WEEE requirements.
Instructions for Disposal of WEEE by Users in the European Union
The symbol shown below is on the product or on its packaging which indicates
that this product was put on the market after August 13, 2005 and must not be
disposed of with other waste. Instead, it is the user’s responsibility to dispose of
the user’s waste equipment by handing it over to a designated collection point for
the recycling of WEEE. The separate collection and recycling of waste equipment
at the time of disposal will help to conserve natural resources and ensure that it is
recycled in a manner that protects human health and the environment. For more
information about where you can drop off your waste equipment for recycling,
please contact your local authority, your household waste disposal service or the
seller from whom you purchased the product.

Figure 25-1: WEEE Symbol

Page 293

You might also like