Scribd
Upload
169 views

E Motion Programming Instructions - LR 1

Uploaded by

Mario Coutinho
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
169 views

E Motion Programming Instructions - LR 1

Uploaded by

Mario Coutinho
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

User & Programming Guide

We thank you for your purchase of E-Motion™ automated shades from Elite Window Fashions™. Your shades have been
custom programmed by our factory to automatically stop at the top and bottom of your windows. Please consult this
guide for proper shade operation and programming.

5 Channel Handheld Remote Operating Instructions


Raise Shade: Press and hold button for 1-2 seconds.

Lower Shade: Press and hold button for 1-2 seconds.


Channel LED Lights 1 2 3 4 5

Stop Shade: Press button while shade is in motion.


Up
Intermediate Position: Press button when shade is
Stop /
Intermediate Position Transmitter stopped (must be set by user, see pg. 2 for setup).
Model: BF-305W
Freq: 433.92MHz
Down Battery: CR2430 Tilt Shade (High-Lite® & Sheer Horizontal Shades only):
C L
Press and release or button.
Channels Up / Down Limit
Change Channels: Press or arrows to change
channels. The numbered LED lights at the top of the
remote indicate the current channel. When all LED lights
Front View Rear View are on, the remote will operate all shades.

5 Channel Wall Remote Operating Instructions


Raise Shade: Press and hold button for 1-2 seconds.
(cover plate removed)
Channel Lower Shade: Press and hold button for 1-2 seconds.
LED Lights
Up Stop Shade: Press button while shade is in motion.
Stop /
Int. Position Intermediate Position: Press button when shade is
stopped (must be set by user, see pg. 2 for setup).
Down
C L
Tilt Shade (High-Lite® & Sheer Horizontal Shades only):
Tap or buttons.
Channel Up / Down
Limit Change Channels: Press or arrows to change
Button Button channels. The numbered LED lights at the top of the
remote indicate the current channel. When all LED lights
are on, the remote will operate all shades.

Pg. 1
Pairing a New Motor to Your Handheld Remote or Wall Remote
1) Press and hold the red button on motor for 1-2 seconds until the shade jogs.
2) Select the desired channel to which you want to program the motor.
3) Using a pen or paperclip, gently press the confirm button marked “C” on the remote. The shade will jog to confirm
successful programming.
Operating Shades as Group: By default, when all LED lights on your remote are on, it will control ALL shades within
range. If you wish to create your own group on another channel, simply repeat steps 1-3 for additional motors but pair
the motors to the same channel.

Removing a Motor From Your Handheld Remote or Wall Remote


(Don’t worry, this will not erase the motor’s limit positions)
1) Press and hold the red button on the motor for 4-5 seconds (motor will cycle through two distinct sets of jogs). The
motor has now been removed from all paired channels on all remotes.

ATTENTION: Before attempting any of the programming functions in this section, you must ensure the motor is NOT
grouped on the same channel with any other motor(s).
Follow these steps to isolate a grouped motor for individual programming:
a) Disconnect the power from other motor(s) by either unplugging the battery wand(s) or DC transformer(s) OR
b) Temporarily removing all other shades from the group channel (see section above for removing a motor).

Reverse Motor Rotation Direction


1) Press and hold the “Limit” and “Stop” buttons simultaneously until the motor jogs.

Setting New Upper and Lower Limits


1) Select the channel of the shade you want to adjust.
2) Press and hold the Limit button marked “L” on your remote for 5-6 seconds until the motor jogs.
3) Press “down” button to send shade down. WARNING: MOTOR WILL NOT STOP ON ITS OWN!
4)
adjusted in small increments by pressing “up” or “down” buttons.
5) CONTINUE TO STEP 6.
6) Press “up” button to send shade up. WARNING: MOTOR WILL NOT STOP ON ITS OWN!
7) Press “stop” button when shade is 2” - 3” from top to prevent damage to the shade. Once stopped, shade can be

8)

Setting A “Favourite” Intermediate Stop Position


1) Bring shade to desired intermediate stop position (i.e 50% height, window transom, latch etc).
2) Press and hold the “Limit” and “Up” buttons simultaneously until the motor jogs.

follow us on:

www.elitewf.com
Copyright ©2017 Elite Window Fashions™ | 1 Applewood Crescent, Unit 1 Concord, Ontario, Canada L4K 4K1
Tel: 1-800-387-3566 | Fax: 1-800-665-3672 | email: [email protected]
Pg. 2

You might also like