Manual de Usuario

Wattstopper ®
Relay Panel Interiors

Panel with Digital Lighting Management Support
No: 24811 – 06/24 rev. 6

User Manual
Catalog Numbers • Les Numéros de Catalogue • Números de Catálogo: LMCP8-10V/LMCP24-10V/LMCP48-10V

LMCP8/LMCP24/LMCP48
Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China
SPECIFICATIONS
Input voltage................................................... 115/277V, 120/347V, 50/60 Hz
For 0-10V models:
Sinks up to 100 mA per 0-10V input (50 fixtures at 2mA each)
0-10V signal will open on loss of power to panel
Class 2 connection to two independent DLM local networks
24VDC output................up to 250mA across 2 RJ45 ports per local network
...................................................................(A and B networks, 250 mA each)
Free-topology DLM local network may include Digital Lighting Management
(DLM) switches, occupancy sensors, daylight sensors, load controllers, and
input modules.
Category 5e cable, 150’ per device, up to 1,000 ft. total per local network
Terminals for connection to DLM segment network (BACnet MS/TP)
Segment network parameters
Wattstopper LM-MSTP wire
Linear topology, 4000 ft. maximum per segment
Accessory power (jumper selectable)
LMCP8/LMCP8-10V.............................................................................N/A
LMCP24/LMCP24-10V................. 650 mA @ 15VDC, 400 mA @ 24VDC
LMCP48/LMCP48-10V................. 650 mA @ 15VDC, 400 mA @ 24VDC
................................15VDC to power optional internal Network Controller
....................................................... 24VDC for Class 2 accessory devices
HDR relays (used in both On/Off and 0–10V panels):
Coil voltage, 24VDC, pulse ON and pulse OFF
Mechanically latched contacts
½” K.O. mounting, LV plug-connection, individually replaceable
HDR Heavy Duty Relay contact ratings:
30 A ballast................................................................................... @ 277V
20 A ballast................................................................................... @ 347V
16 A, E-Ballast.............................................................................. @ 120V
10 A, E-Ballast.............................................................................. @ 277V
20 A tungsten................................................................................ @ 120V
30 A resistive................................................................................ @ 347V
20 A receptacle load..................................................................... @ 120V
1.5 HP........................................................................................... @ 120V
SCCR (short circuit current rating) ...........................14,000 A @ 347VAC
Operating conditions:
for indoor use only.................................................... 32–140° F (0–60° C)
....................................................................... 5-95% RH, non-condensing
Upon loss of power, date and time info is maintained for 14+ days.
Programming info (including schedules) is maintained for the life of the
product.
UL and cUL listed (E207852). Listed for receptacle rated circuit control
Complementary Listed to Emergency Lighting Equipment, UL924
OSHPD (OSP) Approved (Certification No: OSP-0257)
WARNING: The DB9 cables cannot be plugged in or unplugged

without powering down the panel.
CONTENTS
Specifications.......................................................................................................................................................................1
Introduction..........................................................................................................................................................................4
Features and Basic Terminology.......................................................................................................................................................... 4
Panel Circuit Board Layout and Connection.....................................................................................................................5
Dip Switches ....................................................................................................................................................................................... 7
Connecting Panels to Other DLM Devices, and Panels to Panels...................................................................................................... 8
Connecting Override Switches Directly to a Panel.............................................................................................................................. 8
Load Numbering................................................................................................................................................................................... 8
Groups, Scenes, Schedules, and Macros..........................................................................................................................9
Group Settings vs. Individual Relay Settings..................................................................................................................................... 10
Group Functionality............................................................................................................................................................................ 10
Scenes............................................................................................................................................................................................... 11
Schedules.......................................................................................................................................................................................... 11
Macros............................................................................................................................................................................................... 12
Dark/Light Events...............................................................................................................................................................12
Astronomical Dark/Light Switching.................................................................................................................................................... 13
Switching Based on Input From an LMIO-301 or LMIN-104 and Photocell....................................................................................... 13
Connecting Switches, Sensors, Photocells, and Other DLM Accessory Devices.......................................................14
Accessory Device Support................................................................................................................................................................. 14
Switches............................................................................................................................................................................................. 14
Occupancy Sensors........................................................................................................................................................................... 14
Daylight Sensors................................................................................................................................................................................ 14
Analog Photocells.............................................................................................................................................................................. 14
Using the LMIN-104 to Interface with Third Party Devices................................................................................................................ 14
Using an LMCP with Room Controllers and Plug Load Controllers.............................................................................15
Load Control Arbitration..................................................................................................................................................................... 15
Programming the LMCP....................................................................................................................................................15
Load Binding to Groups 1–8 (Smartwire)........................................................................................................................................... 16
Push n’ Learn..................................................................................................................................................................................... 16
Programming Using the LMCT-100..................................................................................................................................17
LMCT-100-2 Basics............................................................................................................................................................................ 17
Configuring the Network Settings...................................................................................................................................................... 17
Viewing the Network Status............................................................................................................................................................... 19
Accessing Panel Setup...................................................................................................................................................................... 19
Setting the Panel Location................................................................................................................................................................. 19
Setting the Date and Time.................................................................................................................................................................. 20
Panel Programming........................................................................................................................................................................... 21
Schedules.......................................................................................................................................................................................... 21
Holidays............................................................................................................................................................................................. 22
Panel Status....................................................................................................................................................................................... 22
Accessing Group Setup Options........................................................................................................................................................ 23
Group Loads...................................................................................................................................................................................... 24
Group Occupancy Sensors................................................................................................................................................................ 25
Group Dark/Light................................................................................................................................................................................ 26
Utilities................................................................................................................................................................................................ 28
Load Status........................................................................................................................................................................................ 29
Group Status...................................................................................................................................................................................... 30
Light Level.......................................................................................................................................................................................... 31
2
Occupancy Sensor Status.................................................................................................................................................................. 31
Connecting Multiple LMCP Panels in a Network.............................................................................................................32
BACnet Settings................................................................................................................................................................................. 32
Examples of Using the LMCP in a BACnet Network.......................................................................................................................... 33
Appendix A..........................................................................................................................................................................35
BACnet Objects.................................................................................................................................................................................. 35
3
INTRODUCTION
The LMCP series panels are available for Dimming (LMCPx-10V) or INTERIOR ENCLOSURES
Switching (LMCPx) control of lighting and plug loads. The panels can be
networked together to enable automation through out an entire facility.
With LMCP panels, you can maintain code-compliant control of building exterior
lighting as well as larger interior areas. Recommended applications include office
building lobbies, corridors, loading docks, school gymnasiums, commons areas
and hallways. LMCP panels are also ideal for retrofit scenarios where mounting
control equipment near existing branch circuit breakers is beneficial, and digital
switches, sensor devices, and load parameter configuration are required to meet
complex operational sequences.
The HDR panel relays respond to inputs from Digital Lighting Management
(DLM) switches, occupancy sensors, daylight sensors, input modules and
0-10V outputs on dimming panel models.
Multiple panels may be networked together for global control operation
without the use of a Network Controller or BAS. The LMCP panel also
provides a native-BACnet integration solution via BACnet MS/TP, or with
optional NB-ROUTER, BACnet/IP. Relay, group, and control device status,
including occupancy sensor status, are available as BACnet objects. When a Figure 1: Panel interior and enclosures
Wattstopper Network Controller is used, it will automatically recognize LMCP
panels and map them to the browser-based user interface so that they can be configured with minimal additional setup.
Features and Basic Terminology

Groups
A group allows you to control one or more relays in one or more panels. Groups provide an easy way to assign parameters quickly to
multiple loads.
Each group has seven parameters that will determine the behavior of the relay. In a typical application each relay in a group will be set
to the same parameters, so that lighting in multiple areas, controlled by different panels can all be set to follow the same schedules and
behavior. However, it is also possible to program a relay in a group to different behavior, if needed. So, for example, if a relay controls a
hallway or corridor that needs a different time delay before turning off, you can change the value for that relay while still having it follow
all of the other behaviors of other relays in the group. A panel can store information for up to 99 groups, but when panels are networked
together more groups are available. Each relay can belong to one or more of those groups. Groups are discussed in detail in the section
“Groups, Scenes, Schedules, and Macros” on page 9.
NOTE: If a relay in a group has been programmed to different behavior, it is possible for the group settings to override the individual
relay settings. See “Group Settings vs. Individual Relay Settings” on page 10 for details.
NOTE: If using the LMCP in conjunction with an LMSM-3E or LMSM-6E Segment Manager, it is important to understand that groups in
the LMCP are separate from Segment Manager groups, which can only be accessed by the Segment Manager itself.
Channels
A channel is a label for a BACnet data object. A BAS integrator sends messages to a channel to schedule After Hours (AH) and Normal
Hours (NH). Channel is a binary value. Note that a value of “Active” sets the channel to AH while a value of “Inactive” sets it to NH.
Part of what a group does is to respond to scheduled events that determine when Normal Hours and After Hours begin. Because a
channel message also determines Normal Hours and After Hours, it is important to understand the difference between groups and
channels. As mentioned above, a panel has 99 memory locations for groups. But since panels can be connected, the total number of
groups is much larger. Therefore a group number can be higher than 99, but it is still stored in one of the 99 slots. The channel number
will correspond to the slot number where the group number is stored.
Groups 1-8 will always correspond to Channels 1-8. Above number 8, the group numbers are stored into the slots in the order they are
created. So, for example, if group 52 is the first group that you program on a panel, it will be stored in memory location 9 and therefore,
you would send a message on channel 9 to affect Normal Hours or After Hours for group 52.
NOTE: Assigning group numbers above 99 requires LMCS-100 software, and in the software, you will view the groups in the order they
were created, so are able to determine the channel number.
Smartwire
Smartwire provides a quick and easy way to assign loads (relays) to groups, using the buttons on the panel. When programming directly
on the panel, Smartwire applies only to groups 1–8. However, if using the LMCT-100-2 to program the panel, you can use Smartwire
with groups 1–99. See “Load Binding to Groups 1–8 (Smartwire)” on page 16 for details.
Push n’ Learn
Push n’ Learn (PnL) is the method used to bind loads to sensors and switches, via button pushes. See “Push n’ Learn” on page 16 for details.
Schedules
Schedules allow you to turn loads on or off at specific times. There are 254 schedules available per panel. A group can also respond to
schedules sent from an LMSM Segment Manager or BACnet-enabled BAS. See “Schedules” on page 11 for details.
Dark/Light
Dark/Light settings allow you to specify turning a group on or off based the amount of outside light. This can be done either with an
astronomical schedule that calculates sunrise and sunset based on your latitude and longitude, or else based on an LMIO-301 photocell
input module or LMIN-104 set to it’s photocell function. Up to 32 dark/light settings can be stored per panel. For details, see “Dark/Light
Events” on page 12.
4
PANEL CIRCUIT BOARD LAYOUT AND CONNECTION
The LMCP contains two types of circuit boards:
• The LMRD board is the relay control board. There are two different versions—one for LMCPx switching panels and one for LMCPx-
10V dimming panels (see Fig. 2a and 2b). A single board can control 12 relays.
• The LMPI board is the main “Panel Intelligence” for the panel. It connects to the Local DLM network and to other panels or other
BACnet devices (see Fig. 3a and 3b).
NOTE: The LMCP-8 contains a single LMRD board (only 8 of the 12 connections are used). The LMCP-24 contains two LMRD boards.
The LMCP-48 has four LMRD boards, with 2 boards placed above and 2 boards placed below the LMPI.
The LMRD boards connect to the LMPI board other with DB9 cables. They must be connected as follows:
• LMCP 8 – Use the top left(#1) DB9 jack.
• LMCP 24 – Use the top left (#1) DB9 jack for the left LMRD board and the top right (#2) jack for the right LMRD board.
• LMCP 48 – Use the top left (#1) DB9 jack for the top left LMRD board, the top right (#2) jack for the top right LMRD board, the
bottom left (#3) jack for the bottom left LMRD board, and the bottom right (#4) jack for the bottom right LMRD board.
Power to the relays comes from the transformers through the LMPI and into the LMRD boards.
Figure 2a: LMCPx – Switching Panel

LMRD Board
Relay Connection Header Relay Status LEDs – The LED will be ON when the relay
turns on, and OFF when the relay turns off. It will blink during
the transition between Normal Hours and After Hours, for the
amount of time specified with the Blink parameter. (If blink time
is set to 0, it will not blink.)
In Smartwire mode, the LED will BLINK on and off when relay
is included in Group, and OFF when relay is excluded from
Group.
In PnL mode, the LED will be ON when relay is selected for
binding with buttons, and OFF when not selected.
Override Buttons and Status LEDs 1–6
Power Indication LED
DB9 Jack – For connection to LMPI

card
12/8 Jumper – For configuring whether the

card drives 8 or 12 relays (jumpered by default
in LMCP8 panels)
Service LED – Blinks once per second if

there is proper communication between
LMRD and LMPI boards. If you press and
hold the button next to the LED, the LED will
remain on instead of blinking.
Override Buttons and Status LEDs 7-12
Relay Override Buttons –Toggle relay ON or OFF depending

on the state of LED.
In Smartwire mode, selects or deselects relay to be included
into a Group.
In PnL mode, selects relay to be bound to a DLM device.
Remote Override Terminal (available on switching LMRD

boards only)
P: Pilot signal
Figure 2a: LMRD Circuit Board
C: Pilot common
S: Override signal
C: Override common
5
Figure 2b: LMCPx-10V – Dimming Panel
LMRD Board
0-10V Connections
Override Buttons and Status LEDs Connect purple wire on “+” terminal,
Relay Connection Header
and pink wire on “-” terminal on the
removable connector
+
–
DB9 Jack – For connection to LMPI card
Service LED – Blinks once per second if

there is proper communication between
LMRD and LMPI boards. If you press and
hold the button next to the LED, the LED will
remain on instead of blinking.
6
The photo below shows the current version of the LMPI board.
An older version of the board is shown on the following page.
Figure 3a: LMPI Circuit Board rev 7
Microcontoller activity indication LEDs (2 blue). The

LEDs toggle every half second while the microcontroller
is operating. They will both be on solid when AC power is
lost and all power down data has been saved. They will
stop blinking when Factory Defaults Request is happening,
or when first powered from the factory, until all the data is DIP Switches (see details below)
initialized.
Room Bus Network Communication Activity

DB9 Connections to LEDs – Light when communication is active on
LMRD Cards Micro USB Port – room bus A or B.
used for updating
firmware IR Interface – used for
Reset Button – resets RJ-45 jacks for
communication with
micro-controller chip and is Connection to DLM
LMCT-100
similar to cycling power on SD Card Slot – Devices
and off For future use
Transformer
Power
Connector
Aux Power
Jumper
Selection
Aux Power
Connector
SW2 – 511 ohm
Group LEDs – Indicates the Group Buttons – Toggles Group 1 to 8
Bias Up
status for Group 1 to 8 for when pressed and released. Also used to
SW3 – 511 ohm
loads in this panel only, where enter and exit Smartwire mode.
Pull down
any member load ON indicates
(behind MS/TP Connector) SW4 – 120 ohm ON, and all member loads
Termination Resistor OFF indicates OFF. Blinks
LMRD Communication (behind MS/TP Connector)
Activity LEDs – Light when during Smartwire mode.
communication occurs MS/TP Connector –
between one of the four For connection to other
LMRD cards. panels - 3 connections Panel Config Button and LED
available
Dip Switches
The default for all dip switches is OFF.
1-4: Not currently used

5: OFF is used with HDR relays and provides a 20ms pulse. ON is used with RR-7 and RR-9 relays, and provides a 50ms pulse.
6: OFF routes unicast DLM Network messages internally. ON routes unicast DLM Network messages out the RJ-45 jacks. Set this to
ON only if using an external diagnostic tool to view those messages. This will slow down DLM Network communications.
7: OFF turns the relay status LEDs on and off during PnL (but not the relays). ON turns both the relays and status LEDs on and off
during PnL.
8: OFF=Relay status LEDs follow Pilot. ON=Relay status LEDs follow logic (for use with RR-7 relays, which have no pilot wires).
7
Differences between the rev 3 LMPI board and the rev 7 LMPI board:
• The Pull Down, Pull, Up, and Termination Resistor are jumper plugs instead of dip switches.
• There is no SD Card Slot (not currently used)
• Microcontroller and LMRD Status LEDs silk screen labeling changed on rev 7 board
• Group button silk screen labeling simplified on rev 7 board
Figure 3b: LMPI Circuit Board rev3
J11 – 511 ohm J12 – 511 ohm J13 – 120 ohm

Pull Up Pull down Termination Resistor
Connecting Panels to Other DLM Devices, and Panels to Panels

There are two DLM local networks (labeled A & B) used to connect DLM devices such as switches, sensors, photocell input modules,
and room controllers. The networks are labeled A and B. Each network has two RJ-45 jacks, for connecting Cat5 cable. Only LMRJ
cable should be used. It is not important which jacks are used. For more details, see “Connecting Switches, Sensors, Photocells, and
Other DLM Accessory Devices” on page 14.
Panels can also be connected to each other, using the MS/TP connectors and LM-MSTP wire.
NOTE: Do not connect panels together with Cat 5e cables.
Connecting Override Switches Directly to a Panel

Non-DLM switches can be connected directly to the non-dimming version of the LMCP, using the Remote Override Terminals next to the
Relay Connection Headers. Only a 2 wire momentary switch, with or without a pilot light, can be connected. If both the pilot light and the
momentary switch are part of the same device, then it is likely that there will be a single “common” or “ground” signal; it can be wired to
either of the terminals labeled C.
P: Pilot Signal
Pilot Light
24VDC (max 5mA)
C: Pilot common
S: Override Signal
Momentary
PC SC C: Override common
Push Button
NOTE: These connectors are only found on LMCPX switching panels, and not on the LMCPx-10V dimming panels.
Load Numbering
Load IDs are assigned on the panel based on the LMRD cards. Loads are numbered on a single card from top to bottom. With multiple
cards, numbering continues from left to right, top, then bottom. So on an LMCP-48, loads are numbered as follows:
• Top Left Card – Loads 1–12 • Top Right Card – Loads 13–24
• Bottom Left Card – Loads 25–36 • Bottom Right Card – Loads 37–48
8
GROUPS, SCENES, SCHEDULES, AND MACROS
A group allows you to control one or more relays in one or more panels. Each group has seven parameters that will determine the
normal hours/after hours behavior of the relay(s):
Parameter Definition
Blink Amount of minutes load stays ON, when a scheduled event occurs that switches the load OFF when
transitioning from Normal Hours to After Hours. The relay will turn off and on once, then the Override LED for
that relay will blink continuously for the time period. The LEDs for all switches bound to that group will also
blink continuously. Pressing the button will keep the load ON and the time delay countdown will start. When
the countdown reaches 0, the blink function re-occurs.
NOTE: Blink does not apply when transitioning from After Hours to Normal Hours.
Possible values are:
• None
• 1–240 minutes
• Use Load – If set to this value , each individual load will use the value of the same parameter found
under the Load Settings menu.
• Reset to Load – This value is identical to “Use Load”.
Time Delay NH If a load is commanded to turn ON when the schedule switches to Normal Hours, the load will automatically
turn OFF after the time delay expires. If the load is turned on manually by a switch after the schedule
switches to Normal Hours, the load will again automatically turn OFF after the time delay expires.
Possible values are the same as Blink. Default is “None”
Time Delay AH Identical to Time Delay NH, but the behavior occurs when the schedule switches to After Hours. Works in
conjunction with Blink.
Possible values are the same as Blink. Default is “120 minutes”.
Transition AH > NH Behavior of the relay when Normal Hours begins.
Possible values:
• 0–100%
• LNZ – Returns to load to the last value that was not 0 (completely off)
• Do Nothing – No change occur
• LNZ Occupied – Returns to load to the last value that was not 0 (completely off) if the room has an
occupancy sensor and the sensor indicates the room is occupied. If the room is unoccupied or if there
no sensor in the room, there is no change to the load.
• Use Load – This uses the value for each individual load instead of a group value. Setting this value for
individual loads is only possible if using LMCS-100 software.
• Turn Off – Turns the load Off
Transition NH > AH Behavior of the relay when After Hours begins.
Possible values are the same as AH–>NH.
Sensor NH Determines how the relay responds to sensor input during Normal Hours. Possible values are:
• Nothing – Load does not respond to occupancy sensor
• Off Only – Responds to sensor input when vacancy is detected but not when occupancy is detected
• On Only – Responds to sensor input when occupancy is detected but not when vacancy is detected
• On/Off – Responds to sensor input for both occupancy and vacancy detection
• Off Only Internal – Responds to vacancy commands only. Instead of using the default value of one
minute for the blink warn feature, the sensor will use the amount of time entered in the Blink parameter.
• On Only Internal – The load responds only to Occupancy commands and once the load is on, it will
not shut off for the length of time entered in the Time Delay NH parameter. Instead of using the default
value of one minute for the blink warn feature, the sensor will use the amount of time entered in the
Blink parameter.
• On/Off Internal – Responds to both occupancy and vacancy commands. Instead of using the default
value of one minute for the blink warn feature, the sensor will use the amount of time entered in the
Blink parameter.
• Use Load – This uses the value for each individual load instead of a group value. Setting this value for
individual loads is only possible if using LMCS-100 software.
NOTE: Keep in mind that this parameter determines whether the loads assigned to the group will respond
to sensor input. It does not determine whether the loads will turn on or off. That is set within the
sensor programming (either on the sensor itself, or by using the LMCT-100-2 remote or LMCS-100
software).
Sensor AH Determines how the relay responds to sensor input during After Hours. Possible values same as above
NOTE: The start times for normal hours and after hours are determined by a Schedule. For details on Schedules, see “Schedules” on
page 11.
9
A group can be set to one of six macros, which contain pre-defined values for each of the seven parameters. Or, you can customize the
setting for your own specific needs. For details, see “Macros” on page 12.
Group Settings vs. Individual Relay Settings

As was mentioned in the introduction, it is possible to assign different parameter values to one or more relays that are part of a group.
Example: You want to assign all offices on a floor to a single channel, so you can schedule all lights to be manual on and off at 7:00 pm,
with a one hour override. However, the owners want to have a two hour override for their own offices.
So a group of all relays can be set up and scheduled to have a 1 hour override, but then the two individual relays for the owners office
can be set to 2 hours. Without this feature, you would need two groups—one for the owners’ office and a second for the rest of the
offices—and would have to schedule each group separately.
Programming Individual Relays and Overriding Them
LMCS-100 software is required to program the individual loads (relays) separate from the group. (The LMCT-100-2 remote provides
access to the Blink parameter but not the others).
Under certain circumstances, the group settings will override the previously programmed settings for an individual load:
• LMCS-100 provides an option when loading group settings into the panel to override the individual settings. If you don’t select this
option, the individual load settings remain.
• When using an LMCT-100-2 to send group information to the LMCP, the group settings will override the individual load settings.
Therefore, you should not use the LMCT-100-2 to send group information if you have previously programmed individual settings.
If using the Smartwire functionality to add a load after groups have been programmed, the group parameters will be applied to the new
load as follows:
• If all of the loads currently assigned to the group have the same parameter values, those values will be applied to the new load.
• If one or more loads currently assigned to the group have different parameter values than the other loads in the group, no
parameter values will be applied to the new load. So if that load had been previously programmed, its values will remain. If no
values were previously programmed, the default values will be applied.
Group Functionality
Group Numbers and Memory Locations
Each panel has 99 memory locations for storing group parameters. Groups 1–8 can be set up and controlled by buttons on the LMPI
board. Groups 1–99 can be accessed from the LMCT-100-2 wireless configuration tool or LMCS-100 software.
If multiple panels are networked together, all loads from different panels that are assigned to the same group will respond to commands
sent to that group. So, for example, you might have panels on three different floors and assign the relays controlling the corridors on
each floor to the same group number. You can then control all corridors on those floors together.
Even though each panel has only 99 memory locations for storing group information, it is possible to “rename” a group to a different
number. There are a total of 65,534 group numbers available. In this way multiple panels can be networked together and allow both
coordinated relay behavior (when the group numbers match between panels) and independent behavior (when the group numbers are
unique to a panel).
NOTE: LMCS-100 software or control via a BAS is required in order to set up and use group numbers higher than 99.
Group Status Indicators
The LMCP provides an easy visual indication of the status of the group. For Groups 1–8, If any relay assigned to a specific group is ON,
then the Group LED for that group will also be ON. So for example, if a group is controlling several different rooms, and an occupancy
sensor in one room has turned on the lights for that room, the associated group button LED will be ON.
Additionally, if a DLM switch is connected to a panel and programmed to control a multiple loads, then the LED for the button controlling
those loads will be ON, if any relay connected to one of those loads in any networked panel is ON.
BACnet Control
Groups also allow BACnet control of relays in multiple panels, as well as all DLM devices connected to those panels.
The only panel-specific BACnet objects are Binary Value (BV) 201–299, for Channel Occupancy Control. Sending a value of TRUE to a
channel BV will set the Group to Unoccupied, also referred to as After Hours operation. Sending a value of FALSE to a channel BV will
set Group to Occupied, also referred to as Normal Hours operation. The reason that After Hours corresponds to True instead of False
is that Normal Hours operation is the default state for a given channel. Therefore setting a group to After Hours requires activation (in
essence, turning After Hours “on”).
Since a panel only has 99 group memory locations, only 99 Channels are available. But as mentioned previously, groups can be
renamed, so you have the ability to control up to 65,534 possible groups.
NOTE: Object support for accessory devices connected to panels is described in Technical Bulletin TB-175, available at
http://www.wattstopper.com/resources/download-center/tech-bulletins-whitepapers.aspx.
A group action (button press, etc.) will always broadcast across the network. Every panel that has a group configured with the target
group number responds to the action. Group set up is a local function that is conducted at each panel location.
For more details about BACnet, see “Connecting Multiple LMCP Panels in a Network” on page 32.
10
Occupancy Sensor Events for Groups
An occupancy sensor event determines how loads assigned to a group will respond, based on input from an occupancy sensor. You can
program up to 99 events. A single event will be assigned to a group.
NOTE: If using multiple occupancy sensors, when programming with the LMCT-100, you should only assign ONE sensor input to a
group. Assigning more than one sensor to a group will lead to inconsistent response (but you can assign different sensors to
different groups). If you need to assign multiple sensors to a group, use the LMCS-100 software to program the actions. The
LMCS software has additional capabilities for programming input from multiple sensors.
NOTE: Occupancy sensor events can be assigned to either a group or a scene. For details on scenes, see below.
For each group, there is an Occupancy parameter (triggered when the sensor detects occupancy) and a Vacant parameter (triggered
when it detects vacancy). For group events, the available values for both occupancy and vacancy are:
• 0–100% – Load goes to the specific value selected
• LNZ – Set the load to the last non-zero level.
• Turn Off – This relinquishes the load—it doesn’t actually “turn off” the load. The loads will still wait for the sensor delay timers to
expire before turning off. If the Partial Off parameter on the Load Settings menu is a value other than 0, the load will go to that
level.
• Do Nothing – No change to the load.
• NH Ovrride – Set the load to Normal Hours. The value of the AH–>NH parameter for the group will be applied.
• AH Ovrride – Set the load to After Hours. The value of the NH–>AH parameter for the group will be applied.
• Normal Hrs – Set the load to Normal Hours. All settings found on the Normal Hours tab within LMCS-100 for loads and sensors will
be applied. (These settings are only available if you are using LMCS-100 software.)
• After Hrs – Set the load to After Hours. All settings found on the After Hours tab within LMCS-100 for loads and sensors will be
applied. (These settings are only available if you are using LMCS-100 software.)
Scenes
The LMCP also has the ability to control Scenes (but only on the panel’s Cat 5e local network). Scenes are similar to Groups in that they
control group of loads but also provide the ability to fade between one value and another when the scene is changed. For a switching
LMCP, if assigning relays within the LMCP to a scene, it will switch relays on or off, since no dimming is possible.
There are sixteen possible scenes per “room” (or in this case a panel). When a scene is activated (typically by assigning it to a switch),
all loads assigned to that scene will respond. You can select which loads are included in the scene.
Scenes are normally assigned to a button switch (the LMSW-105 5-Button Switch is commonly used for this but any button can be set
as a scene button).
Scenes can also be triggered by Occupancy Sensors and Dark/Light events. The load control is similar to that of Occupancy Sensors
and Dark/Light events for groups, but for scene events, you determine whether to turn the scene On or Off.
NOTE: Even though Scene events are separate from Group events, in the LMCT-100-2, you access these events from the Group Occ
Sensors and Group Dark/Light screens within the Group Setup menu
Schedules
You can schedule up to 254 date and time based events per panel. Each event is assigned to a group, and determines one action for
the group. For each event, you specify the time the event occurs. You also specify the days of the week in which the event will occur.
Additionally, you specify whether the event will occur on any day designated as a holiday.
The possible actions sent to the group include:
Schedule Type Action Description

After Hours Transitions Groups to After Hours (unoccupied) state
Normal Hours Transitions Groups to Normal Hours (occupied) state
On Turns group loads ON without changing the current occupancy status
Off Turns group loads OFF without changing the current occupancy status
Do Nothing No action
If panels are networked and multiple panels use the same group number to control relays in those panels, then any events scheduled
in one panel will affect the other panels (since events are always assigned to a group number). By using different group numbers in
different panels, you can limit which panels will respond to those scheduled events.
Assigning a Panel to be the Master Clock
Every LMCP has a clock in it, which allows you to set time and date for controlling schedule events and calculating sunrise and sunset for
Dark/Light events. To set the clock, use the LMCT-100-2 hand held remote, LMCS-100 software, or BACnet Time Synchronization via a BAS.
Additionally, if you have more than one panel networked together, any panel can be set to be the master clock. It will periodically send
out clock information to the other panels so that they remain synchronized. You can set how often the master sends the clock message.
The advantage of having any panel act as a master is that if the master panel is taken off-line for any reason, any other panel can be
easily set to be master and all panels will still remain in sync. (Note that if the original panel is put back on-line you will want to revert the
replacement master or the original panel to back to being a slave, so that you don’t have two master clocks on the network.)
To assign a panel as the master, you need LMCS-100 software. For more information on LMCS-100, see “Programming the LMCP” on
page 15.
11
Macros
A macro is a set of pre-defined values for the seven parameters that are part of a group. Each group can be set to a specific macro,
or to use no macro and instead use a customized set of values. There are six macros in the LMCP. Following is a description of the
intended use for each macro, followed by a list of all parameter values:
NOTE: If you want to set up custom parameters that are similar to one of the macros, select that macro first, then go into Custom mode
and change only the value that different from the macro default.
• Manual – This macro should be used when there are no occupancy sensors or switches associated with the Group and only on/off
actions from schedules or dark/light are intended. Since On/Off changes are based only on schedules and dark/light sensors, the
only parameter in the macro that has any effect is Blink, which will provide a warning to occupants by momentarily shutting the load
off and then back on.
• Override Time AH – This macro is designed for situations where only switches are used (no occupancy sensors). An override time
delay is set so that if a switch is used to keep the light on during after hours, the load turns off after two hours. The load is set to
turn ON when entering Normal Hours. If you instead want to require that the load be manually turned on, start with this macro when
creating the group, select CUSTOM, and modify the Transition AH > NH action to a value of “Do Nothing.” Additionally, adjust Time
Delay AH if you want a different amount of time before the load turns off.
NOTE: The settings in this macro are used for Groups 1–8, when you use Smartwire to assign relays to a group.
• Sensor Day Disable – For use with occupancy sensors, this macro turns all loads ON during Normal Hours; they can be turned off
or back on manually, with no override time delay. When After Hours begins, loads are turned OFF and sensor functionality is set to
Auto On/Off. A two hour time delay is set for cases in which some loads in the group are not bound to sensors, but only to switches.
• Sensor Man-On NH – In this macro, relays are left OFF when Normal Hours begins. Occupancy sensors trigger loads on occupant
arrival, but do not time out until after hours. When After Hours begins, loads turn OFF and sensors switch to Auto On/Off. As with
the Sensor Day Disable macro, a two hour time delay is set for cases in which some loads in the group are not bound to sensors,
but only to switches.
• Sensor Auto – This macro sets sensors to Auto On/Off for both Normal Hours and After Hours operation, so loads turn ON only
based on sensor or switch input. A 120 minute override time delay is used during the After Hours period. This allows for consistent
functionality in response to sensors at all times, while accommodating the inclusion of relays not bound to sensors that share the
same operational time window.
• Auto Switch-1xx – This macro is designed to work with the AS-100 Automatic Control Switch. The AS-100 is a switch that controls
the line voltage (instead of sending a low voltage control message to the panel or other room controller). Instead, the AS-100
responds to timed power interrupt signals coming from a relay in the panel, providing automatic shutoff with a blink warning when
transitioning between normal hours and after hours. Other timed interrupt signals can turn the power on or off. You assign a relay
to “AS-100” mode using LMCS-100 software or on the Load Config (PnL) menu in the LMCT-100-2. All relays in “AS-100 mode”
remain closed except for the timed interrupts. If this macro is assigned to a group, you should only assign relays in “AS-100” mode
to that group. When using this Macro, none of the seven group parameters apply. (Although Blink is set to 5 minutes, the blink time
is actually controlled by the AS-100, not the LMCP.)
NOTE: Since selecting this mode puts all relay in the associated group into “AS-100” mode, you should not assign those relays to
another group set to a different macro.
NOTE: Keep in mind that Macros only affect the behavior during the transitions to Normal Hours and After Hours, plus the response to
occupancy sensors. Any scheduled events and input from photocell sensors will still affect the loads.
NOTE: The values for the seven parameters are only applied to the Group when the Macro (or custom) information is sent to the LMCP
from the LMCT-100-2 remote or LMCS-100 software. If a subsequent message is sent to the LMCP with a different value for
a parameter, the original value is overwritten, and will only change back to the original value if the Macro is sent again to the
group. So for example, if a relay is assigned to two different groups, and each group has been assigned a different Macro, the
last macro sent to the LMCP will determine the behavior of that relay.
Macro Values
General Settings Transition Settings Sensor Behavior
Macro Blink Time Delay NH Time Delay AH NH>AH AH>NH NH AH
Manual 5 min None None Do nothing Do nothing Off Only Off Only
Override Time AH 5 min None 120 min Turn off Turn on Off Only Off Only
Sensor Disable Day 5 min None 120 min Turn off Turn on Follow On Auto
Only
Sensor Man-On NH None None 120 min Turn off Do nothing Off Only Auto
Sensor Auto 5 min None 120 min Do nothing Do nothing Auto Auto
Auto Switch-1xx 5 min None None Do nothing Do nothing Do nothing Do nothing
DARK/LIGHT EVENTS
The LMCP can be programmed to turn relays on or off based on when it becomes dark outside (night) or light (day). You can program
up to 32 separate dark/light events, and each event is assigned to a group or a scene. For each event, you can select whether to base
the change from dark to light and light to dark on either an astronomical calculation of sunrise and sunset, or from a photocell connected
to an LMIN-104 or LMIO-301. You can have multiple LMIN-104s/LMIO-301s connected to the network and assign different groups to
different LMIN-104 or LMIO-301s, or you can have a single LMIN-104 or LMIO-301 but assign different light thresholds to different
groups.
NOTE: You can only select a single LMIN-104 or LMIO-301 if programming with the LMCT-100-2. To use multiple LMIN-104s/LMIO-
301s, you must program with the LMCS-100 software.
12
Each Dark/Light event has a Dark parameter and Light parameter.
If the event is assigned to a group, then for each parameter you can choose the following:
• 0-100% – Load goes to the specific value selected
• LNZ – Set the load to the last non-zero level.
• Turn Off – This relinquishes the load—it doesn’t actually “turn off” the load. The loads will still wait for the sensor delay timers to
expire before turning off. If the Partial Off parameter on the Load Settings menu is a value other than 0, the load will go to that
level.
• Do Nothing – No change to the load.
• NH Override – Set the load to Normal Hours. The value of the AH–>NH parameter for the group will be applied.
• AH Override – Set the load to After Hours. The value of the NH–>AH parameter for the group will be applied.
• Normal Hrs – Set the load to Normal Hours. All settings found on the Normal Hours tab within LMCS-100 for loads and sensors will
be applied. (These settings are only available if you are using LMCS-100 software.)
• After Hrs – Set the load to After Hours. All settings found on the After Hours tab within LMCS-100 for loads and sensors will be
applied. (These settings are only available if you are using LMCS-100 software.)
If the event is assigned to a Scene, then for each parameter you choose whether to turn the Scene On or Off.
Astronomical Dark/Light Switching

Astronomical Dark/Light Switching
When you use astronomical control of dark/light events, Dark is triggered by sunset and Light is triggered by sunrise, based on your
location. Additionally, you have the ability to select an Offset. This parameter determines when the event will be triggered in relation to
the actual sunrise and sunset time. A positive offset acts as if the time between sunrise and sunset was longer (more daytime), and a
negative offset acts as if there were less time between sunrise and sunset (less daytime). So if you select -20 minutes, the Dark event
will trigger 20 minutes before sunset and the Light event will trigger 20 minutes after sunrise. The diagram below shows the exact time
the events will be triggered based on different offset values.
NOTE: Since sunrise and sunset time are determined by both your location and the date, you must configure the panel or zone
controller with this information. See ”Accessing Panel Setup” on page 19 for details.
Dark/Light Event Triggering
18:07 07:15
17:47 18:37 06:45 07:35
Amount of Daytime
Time ~Noon -20 30

Min
~Midnight 30
Min
-20 ~Noon
Min Min
Offset Offset Offset Offset
Dark Light
aka Sunset aka Sunrise
aka Dusk aka Dawn
Less Offset More Offset More Offset Less Offset

Daytime / Nighttime Nighttime / Daytime
Example: Dallas Astro on 2/9/15

With Offset at 30 minutes Sunset = 18:07 With Offset at -20 minutes
Sunrise = 07:15
Dark ON – Lights turned on at 18:37 Dark ON – Lights turned on at 17:47
Light OFF – Lights turned off at 06:45 Light OFF – Lights turned off at 07:35
Switching Based on Input From an LMIO-301 or LMIN-104 and Photocell

If you control dark/light events from an LMIO-301 or LMIN-104, you can select the amount of light, in footcandles that will trigger the
events. If the light rises above the footcandle amount, a light event will trigger, and if it drops to the exact footcandle amount, a dark
event will trigger.
A Time Delay feature allows you to set the number of minutes after the specified footcandle amount is reached before triggering the event.
This helps prevent unwanted event triggering, for example, when the light temporarily gets darker because of a cloud passing over the sun.
13
CONNECTING SWITCHES, SENSORS, PHOTOCELLS, AND OTHER DLM ACCESSORY DEVICES
Accessory Device Support

Each Cat5 Local DLM Network port, labeled A and B, supports a maximum of 48 communicating devices. Note that the panel itself
counts as one device in each network, so this allows for a maximum of 94 possible accessory devices per panel (2 x (48-1) = 94).
The maximum cable run for a network depends on the number of devices. 150’ of cable is allowed per device; a two device network is
allowed 300’, 3 devices 450’ etc., up to 1,000’ maximum. For example a network that has 6 devices supports a maximum of 900’ of total
CAT 5e cabling with no minimum or maximum spacing between devices. The first five 5 devices could be separated by a 10’ LMRJ (4
total) and the first switch could then be 860’ from the first panel. Since the maximum length is 1000’ for the network, adding additional
accessory devices beyond 6 total will increase the length by 100’ more, no matter how many devices are added.
NOTE: Although the two networks are independent for wiring length purposes, all devices on both networks have the ability to
communicate with each other. This provides the end result of a total of 2000’ of cable between all DLM devices connected to
the panel via CAT 5e cables. Additionally, if connecting two or more panels via MS/TP, each of those panels has 4000’ feet of
connection possible.
Additionally, each network can draw a maximum of 250mA, so the number of devices on a network will be determined by the amount
the devices draw. However, if you add room controllers or plug load controllers to the network, they provide additional amperage for the
other connected devices, up to a maximum of 800mA.
Switches
The panel’s local DLM network supports all models of DLM switches. Switch buttons may be bound to an individual relay (load), scene,
or network group in the panel. If a switch is bound to a group and any load assigned to that group is ON, the LED on that switch will
indicate ON.
There are several advantages to binding a switch to a group:
• If you add a load to a group, that switch will immediately control that load without having to re-program the switch.
• You can assign a switch to the same set of loads controlled by a schedule or dark/light event
• If you have multiple panels connected, and the same group number assigned to loads in those panels, the switch will control the
loads from those other panels in addition to the panel in its local network. This allows you to program a single switch that can be
used as a master, to turn all lights on or off in the case of an emergency or other special circumstance.
Occupancy Sensors
The panel’s local network supports all models of DLM occupancy sensors. Using Push n’ Learn, any number of occupancy sensors can
control the same relay(s) in the local panel. In this case, all sensors must be in the unoccupied state before the relay(s) turn off.
A maximum of 32 sensors can control an individual load. (The total number of sensors controlling various loads is limited only by the
network limitations described above.)
Daylight Sensors
The LMLS-400 and LMLS-500 daylight sensors are capable of controlling relays in the panel as switching loads, or dimming loads if a
dimming capable room controller is connected to the local DLM network.
Analog Photocells
As described in the previous section on Dark/Light Events, the panel’s local network supports the LMIO-301 Analog Photocell Module or
LMIN-104. This module supplies the “light” and “dark” trigger. The panel has user settings for foot candle levels and time delay. The time
delay is used before triggering “light” and “dark” events to establish a dead band and prevent nuisance switching. Only one LMIO-301
per panel can be programmed via the LMCT-100; more can be connected if using LMCS-100 software.
Two types of photocell sensor heads can be used. The LMPO-200 is intended for outdoor use, while the LMPS-6000 is intended
for indoor use where there is direct exposure to high light levels, as would be present adjacent to the glass in an atrium, skylight, or
clearstory.
Using the LMIN-104 to Interface with Third Party Devices

The LMIN-104 Digital Input Interface Module allows integration of 3rd party devices to control LMCP relays or other loads in the DLM
Local Network. The LIN-104 has four input terminals. In addition to On/Off control of loads, it can dim loads up and down, or send
messages such as After Hours, Shed, or Force On to the DLM local network based on external inputs.
The LMIN-104 has three operating modes: Normal, Partition, and Photocell. The LMCT-100-2 or LMCS-100 software is required to
program the modes.
In Normal mode, the LMIN-104 can provide control for up to four 2-wire input or two 3-wire input non-DLM switches or sensors.
Partition mode provides the ability to control partitions in multi-use spaces that are frequently reconfigured. Applications include hotel
and conference center ballrooms and meeting rooms, school multi-use rooms, and other spaces with movable walls.
Photocell Mode ishould be used n for any application where exterior lighting needs to be controlled based on actual ambient exterior
light levels such as parking, site and landscape lighting. Applications with large expanses of skylight, clearstory or atrium glazing can
also benefit from controlling lighting based on ambient light entering the building through the glazing.
14
USING AN LMCP WITH ROOM CONTROLLERS AND PLUG LOAD CONTROLLERS
By connecting room controllers and plug load controllers to the DLM local network, you can increase the number of loads in the network.
The maximum number of loads, including all the loads within the panel, is 64. Since the maximum number of devices on a single
network is 48, the total number of additional controllers possible will also be dependent on the number of other DLM devices on that
network. The same cable length requirements apply as with other DLM devices.
Connecting additional controllers to the panel provides several advantages:
• The loads connected to those controllers can be assigned to groups, the same as the relays in the panel. This allows for scheduling
of those loads and all other group features.
• Dimming loads can be added to the network, provided you have a room controller with dimming capability.
• Current monitoring of plug loads and dimming loads is possible as part of the network control. (Note that current monitoring of
dimming loads within the panel is not available.)
NOTE: There is a maximum of 4 LMRC-10x room controllers, LMPL-101 plug load controllers, and/or LMPB-100 power boosters
allowed per network (A or B), for a maximum total of 8. This applies only to the 10x series and not the 2xx series.
Connecting Room and Plug Load Controllers
Room Plug Load

Controllers Controller
Network A LMPL-
213 102 211 213 221 101
LMCP-24 Maximum # of connected devices per network: 48 (including 1 for LMCP),

for a total of 96. In this example there are 10 devices on Network A and
12 on Network B.
Maximum number of loads, including those in the panel, and on both

networks: 64. In this example, there are 50 loads (24 in the panel, 11 on
Network A, and 15 on Network B).
Maximum of 4 LMRC-10x or LMPL-101 allowed in a network. In this

example, you could add two more 10x controllers to Network A, but
Network B none to Network B.
102 102 102 213 212 213 101
Load Control Arbitration

After the room or plug load controllers are connected to the DLM Local Network and powered up, they automatically negotiate to
determine which controller becomes the Master. This is referred to as load arbitration. The controllers also determine the load numbers
for each relay on the DLM Local Network. By design, the Master is the controller powering the bus with the highest serial number. The
panel will have the highest serial number and therefore be the Master. As a general rule, controllers with more loads have a higher serial
number than lower ones, and room controller have higher numbers than plug load controllers.
Example: The LMCP-24 is connected to an LMRC-101, LMRC-212, and LMPL-201. The panel uses load IDs 1–24, the LMRC-212 uses
IDs 25 and 26, the LMRC-101 uses ID 27, and the LMPL-201 uses ID 28.
NOTE: The panel will reserve IDs based on the number of slots on the LMRD card, not the number of relays installed. So an LMCP-24
with only 16 relays installed will still reserve IDs 1-24.
PROGRAMMING THE LMCP

There are five methods for programming the behavior of the relays in the LMCP. All programming is stored in the memory of the LMCP.
• Directly on the LMCP, using Smartwire, to bind loads to groups 1–8
• Directly on the LMCP and connected switches and sensors, using Push n’ Learn, to bind loads to individual switches and sensors
• Using the LMCT-100-2 hand-held remote. This provides all the functionality as Smartwire, but allows you to program all 99 groups
in a panel, instead of just groups 1–8. It also provides the ability to program connected switches and sensors to groups. Additionally,
you can use the LMCT-100-2 to bind switches and sensors to individual loads, the same as using Push n’ Learn.
15
• Using the LMCS-100 software. You can connect a PC running LMCS-100 to the panel directly, using an LMCI (USB to LMRJ
adapter), or via BACnet. LMCS-100 provides the largest amount of control. If using multiple panels networked together, this is the
recommended method. Programming using LMCS-100 is not described in this guide, but instead in the LMCS-100 User Guide. For
the latest version, go to https://www.legrand.us/wattstopper/software.
• Using an LMJA-8125-AX or LMJA-8300-AX Network Controller or other BAS application through BACnet. A limited number of
parameters are exposed directly through BACnet. For details, see “Appendix A” on page 35. Also see the Segment Manager
User’s Guide.
NOTE: It is strongly recommended that if you are using LMCS-100 software, you do not use the LMCT-100-2 to program the panels or
any connected devices. In a distributed network situation where groups might be assigned across more than one panel, LMCS-
100 will determine which panel’s memory will store the schedules. Sending information to the panels via the LMCT can create
conflicting messages between panels.
NOTE: Upon loss of power, date and time info is maintained for 14+ days. Programming info (including schedules) is maintained for the
life of the product.
Load Binding to Groups 1–8 (Smartwire)

Smartwire provides a quick and easy way to assign loads (relays) to groups, using the buttons on the panel. If programming from the
panel, Smartwire applies only to groups 1–8. Once assigned to the group, pressing the group button to turn that group ON or OFF will
turn the associated loads ON or OFF.
NOTE: If using the LMCT-100-2 to program the panel, you can use Smartwire with groups 1–99.
Keep in mind that if panels are networked together, then once a load is assigned to a network group, turning ON that network group in
any panel will turn ON the associate loads for that group number, even if it is a different panel.
To program using Smartwire:
1. Press and hold a group button for at least five seconds, until the LED next to the group button begins blinking. At this point, all of
the Relay Override LEDs will turn OFF (unless the relay is already bound to the group you are programming, in which case it will
blink).
2. Press the buttons for each load that you want bound to that group, so that their LEDs blink. If a load is currently bound to the group
and you do not want it part of the group, press the button to turn the LED OFF.
3. Press and release the Group button to exit Smartwire mode. At this point, any Relay Override LEDs that were ON previous to
entering Smartwire mode will turn back ON.
4. To test your programming, press the group button to turn it ON. The relays associated with that group will turn ON. You can turn
the group back OFF, by pressing the button again.
Push n’ Learn
You can bind a load to specific controllers such as switches or sensors using Push n’ Learn (PnL). The important distinction between
PnL and Smartwire is that with Smartwire, you are connecting individual loads to a group rather than binding individual loads to
controllers..
PnL vs. Groups
It is possible to assign a controller to more than one load using PnL. In this manner, using PnL is similar to using groups because you
can control multiple loads at the same time. The important difference between using PnL and assigning groups is that groups offer
more functionality, such as schedules and dark/light, whereas PnL can only assign controllers to loads.
Programming the LMCP Using PnL
1. There are three different methods you can use to enter PnL mode:
• Press and hold the Config button on any remote DLM device for at least three seconds, until the red LED on the unit begins
to blink. The location of this button will vary,depending on the device. On many devices (such as switches and occupancy
sensors), you will need a small pointed tool to push the button.
• Press and hold the Panel Config button on the LMPI board of the LMCP for at least three seconds, until the red LED on the unit
begins to blink.
• Use the LMCT-100-2. Select the LOAD CONFIG (PnL) menu, to enter PnL mode.
No matter which method you use, once you enter PnL mode, the red LED on all DLM devices connected in the network will blink,
and you can assign any DLM controller to a load on the panel.
2. When you first enter PnL mode, the Status LEDs for all loads except Load 1 will turn off. The Load 1 LED remains active,
indicating it is the currently programmable load. At this point, the method of programming depends on whether you are using the
LMCT-100-2.
a. If you are not using the LMCT-100-2, press the Config button on the LMCP or any connected DLM device. Each time you press
the Config button, the panel will cycle to the next load. The Status LED for a load turns ON when that load is selected (only one
load LED will be on at a time). When you reach the highest number load, it will cycle back to load 1. You can also jump directly
to a specific load by pressing the Override button for that load on the LMCP, LMRC, LMPL, or LMRC. Once you select the
desired load, you can bind the specific controller to that load. For a switch, you do this by pressing the desired button on that
switch to turn it on. For an occupancy sensor, you use the display and navigation buttons on the sensor to bind that load to the
sensor.
b. If you are using the LMCT-100-2 then you select the load on the LMCT. It starts by default on load 1. To choose another load,
select NEXT, use the left and right arrow buttons to select the desired load, then point the LMCT at the IR sensor and press
Select. The screen for that load’s settings opens. On this screen, you can bind a specific controller to that load. For a switch, you
do this by pressing the desired button on that switch to turn it on. For an occupancy sensor, you point the LMCT-100-2 at the
sensor and select BIND. For more details on programming PnL from the LMCT-100-2, see the LMCT-100-2 User Guide.
16
3. To exit PnL, hold the Config button for 3 seconds, until the LED stops blinking. Or if using the LMCT-100-2, select EXIT.
If you have one or more DLM Room controllers connected to the LMCP, then as when you cycle through the loads by pressing the
Config button, once the last relay is reached on the LMCP, the sequence advances to the Room Controller with the highest serial
number and cycles through the loads on that controller in order.
A primary difference in operation of the LMCP compared to a DLM Room Controller is that by default, while in load configuration mode,
the panel relays do not turn on and off in sequence as the Config button is pressed. Only the LED associated with the relay turns on On
a DLM Room Controller, the load itself will turn on and off.
NOTE: It is possible to change the LMCP so that the relays turn on and off in PnL, just like a room controller. This is done by setting Dip
switch #7 on the LMPI board to the ON position.
PROGRAMMING USING THE LMCT-100

NOTE: In addition to programming the LMCP, the LMCT-100-2 is used for programming many different DLM devices, including
switches, occupancy sensors, and other devices. This user guide only describes the screens specific to network setup,
panel programming, and assigning of groups. Use of the LMCT-100-2 to bind switches and sensors to individual loads
(even when those loads exist in a panel) is detailed in the LMCT-100-2 User Guide.
IMPORTANT: In order to use the LMCT-100-2 with LMCPx-10V, you must have version 6.22 or later firmware installed in the LMCT-100-2.
For details on updating firmware, see the LMCT-100-2 User Guide.
LMCT-100-2 Basics
The LMCT-100-2 provides an easy to read display and a simple user interface that makes it easy to navigate through programmable
features It both send information to and receives information from the LMCP and other DLM devices.
It is important to understand that all information is stored in the LMCP or accessory devices, and not the
LMCT-100-2. Therefore, if you change any values on the LMCT-100-2, you must select the Send option in order to save your changes.
If you press the Home button, Back button, or select Done without first sending the data to the LMCP, that data is not saved.
User Interface Navigation
You navigate from one field to another using  (up) or  (down) arrow keys. The active field flashes between yellow text on black
background and black text on yellow background. Navigation “wraps” around, so if the active field is the top field and you need to get to
the field at the bottom of the screen, pressing  will bring you to the bottom in a single key press.
NOTE: The up and down arrow keys are always used to move between fields. So even when fields are placed on the same horizontal
line, which is often found with the Action options at the bottom of the screen, you still use the Up/Down arrows to move left/right
between fields.
Once a menu field is active, press the Select button to open that menu.
Value fields are used to adjust parameter settings. They are shown within “less than/greater than” symbols: <value>. Change the value
using  and  arrow keys. In general the  key increments and the  key decrements a value. Selections wrap-around if you
continue to press the key beyond maximum or minimum values. Move between value fields using  or  arrow keys.
The button takes you to the main menu.
The (Back) button can be thought of as an undo function. It takes you back one screen. Changes that were in process prior to
pressing the key are lost.
At the bottom of any screen that includes programmable fields, you will see Send and Done (and sometimes additional choices). As
mentioned previously, you must press Send to save your data to the LMCP before pressing Done, if you want to save the values you
set on that screen.
On some screens, one of the options at the bottom of the screen will take you to a secondary, related screen. For example, at the
bottom of the Program Schedules screen is an Active Days option, where you choose which days the schedule will be active. In the
case, the Schedule Active On screen has only a Done option at the bottom—you must return to the Program Schedules screen
before you can send the schedule information to the LMCP.
Configuring the Network Settings

The Network Settings screen allows you to customize settings related to communication over a BACnet network.
Display Description Press
B AT = Scroll Down or Up to Highlight More, then press

S e n s o r C o n fi g u r a t i o n Select.
Load Binding (PnL) then
Load Settings Hint: Navigation “wraps” around, so if you scroll or Select
D a y l i g h t i n g C o n fi g “up”, you can reach More with a single button
B u t t o n C o n fi g u r a t i o n
More press.
Up or Down Select
Button Button
17
B AT =
Adjust Light Level
Global Network then
Utilities Scroll to Global Network. Press Select. Select
Panel Setup
Group Setup
More
Point to the desired

Panel IR Sensor and Point the LMCT-100-2 at the infrared sensor on the Select
press ‘Select’ LMRD board and press Select.
Network - Panel
Network Settings The Panel Network screen opens, with Network

Network Status Select
Settings selected. Press Select
The top line of the screen shows the serial number

of the panel. The Name defaults to the serial
number, but can be changed. Highlight the value
and press Select to open a new screen, as shown
below.
The Device ID must be a unique number within
the BACnet network. By default, it is set to the last
six digits of the serial number, but like Name can
be changed by highlighting the value and pressing
Select.
The MS/TP MAC address is another ID used to
LM Panel 0603981210 identify a device. If you select a value of “Yes” for to move to each
AutoSet MSTP MAC, the LMCP will select a value or
Name: 603981210 parameter
Device ID: 0981210 itself, displayed as the Auto MSTP MAC. If you
A u t o S e t M S T P M A C : < Ye s > change the auto set value to “No” and scroll down, to change the value
or
Auto MSTP MAC: 051 the parameter changes to Manual MSTP MAC and of the parameter
Baud Rate: <38400> you can change the value. then choose
Max Master: <127> SEND and
DONE SEND The default Baud Rate is 38400, but can be press Select
changed. The Max Master is the highest number
the LMCP will try when polling for a master.
Highlight SEND and press Select.
Once again, point the LMCT-100-2 at the infrared
sensor on the LMRD board and press Select. You
return to the Panel Network screen.
Highlight DONE and press Select, or press to
return to the Panel Setup screen.
For a detailed explanation of these parameters,
see “Connecting Multiple LMCP Panels in a
Network” on page 32.
If you press Select with the Name or Device
[603981210 ] ID field highlighted, this screen opens. You can to move to each
or
change the name using numerals or letters, and character
Move to any chacter
with left/right keys. change the ID with numerals only. to change the value
or
Change the character Select ERASE to clear all characters before of the character
with the up/down keys. entering new data. then choose
When finished editing, select DONE to return to the DONE and
DONE ERASE COPY PASTE press Select
Panel Network screen.
18
Viewing the Network Status
The Network Status shows the communication “health” of the network and the number of devices currently found on the network.
Network - Panel
Network Settings From the Panel Network screen, scroll down to

Network Status Select
Network Status. Press Select
The Network Status will display as “Unhealthy”

if it can’t find the BACnet network, or if devices
on network drop off and then reappear while the
Network Status LMCP is polling the network (indicating connection
problems). If devices show up consistently, or
LM 0603981210
if they disappear and do not show up again
Net Status: Unhealthy (which would indicate the device was disabled or Select DONE
Net Device Count: <0> disconnected), the status will display as “Healthy”.
The Net Device Count displays the number of
DONE devices on the BACnet network.
Select DONE to return to the Panel Network
screen. Highlight DONE and press Select, or press
to return to the Panel Setup screen
Accessing Panel Setup

As mentioned previously, this user guide describes the screens specific to Panel Setup. The following screens show how to navigate
into this screen. To avoid repeating the same steps for every function described in the following pages, all sections after this one assume
you have already navigated to the Panel Setup screen on the second main menu screen.
B AT =
Adjust Light Level
Global Network Scroll Down or Up to Highlight Panel Select, then
press Select. or then
Utilities Select
Panel Setup
Group Setup
More

Panel Setup
Location Settings This screen is the starting point for all following
Date and Time instructions.
Panel Programming
Panel Status
Setting the Panel Location

Setting the panel location provides sunrise/sunset information to the panel, for use when you set a schedule according to an
astronomical clock.
NOTE: The LMCT-100-2 has a limited number of locations to choose from. For a much more extensive list, use the LMCS software to
access this feature.
19
Panel Setup
Location Settings When you first enter the Panel Setup screen,
Date and Time Location Settings is already highlighted. Select
Panel Programming Press Select.
Panel Status

Select the desired State, and City. The Latitude/

Location Setup to move to each
Longitude/Behind/Ahead Hours are fixed values. or
Region USA Then highlight SEND and press Select. parameter
State: Rhode Island
City: Newport Once again, point the LMCT-100-2 at the infrared to change the value
or
Latitude: 41N sensor on the LMRD board and press Select. You of the parameter
Longitude: 71W return to the Location Setup screen. then choose
Hours Behind GMT 5 SEND and
DONE SEND Highlight DONE and press Select, or press to press Select
return to the Panel Setup screen
Setting the Date and Time

The date and time are used for schedules, including both manually set events and sunrise/sunset determination (in conjunction with the
location settings).
Panel Setup
Location Settings From Panel Setup, scroll to Date and Time. Press then
Date and Time Select. Select
Panel Programming
Panel Status

Date and Time Set Scroll to each field and set the value. An illegal to move to each
or
Ye a r : <2014> date (for example, February 30) cannot be entered. parameter
Month: <August> After selecting all values, scroll to DSTSTD and to change the value
Date: <14> press Select. or
of the parameter
Hour (24 Hour): <16>
Minute: <37> NOTE: There is no clock in the LMCT-100-2, then choose
so the time values will not change if you DSTSTD and
SEND DSTSTD DONE remain on this screen longer than a minute. press Select
This screen determines if the panel will follow to move to each
D S T C o n fi g u r a t i o n Daylight Savings Time. If you set Follows DST or
parameter
to “Yes”, you can choose a value of “Auto” or
F o l l o w s D S T: < Ye s > “Manual” for Method. Select BEGINS. to change the value
Method: <Auto> or
NOTE: If you set Follows DST to “No”, the of the parameter
Method field disappears. Highlight DONE then choose
and press Select, or press to return to BEGINS and
BEGINS ENDS DONE press Select
the Date and Time Set screen
20
Depending on whether you choose a value of

DST Automatic Rules Auto or Manual, the screen changes. For Auto, to move to each
or
Begins: you select the week, the day of the week, and parameter
<2nd> the month. For Manual, you select a specific date to change the value
<Sun> (for example, March 20th). Select DONE to return or
<Mar>
of the parameter
to the DST Configuration window. Repeat the
process for the end of DST by pressing ENDS. then choose
DONE and
DONE Then select DONE to return to the Date and Time press Select
Set screen.
Date and Time Set to move to each

Highlight SEND and press Select. or
Ye a r : <2014> parameter
Month: <August> to change the value
Date: <14> sensor on the LMRD board and press Select. You or
Hour (24 Hour): <16> return to the Date and Time Set screen. of the parameter
Minute: <37> Highlight DONE and press Select, or press to then choose
return to the Panel Setup screen SEND and
SEND DSTSTD DONE press Select
Panel Programming
Panel Programming functions include:
• Schedules – Allows you to specify an event and assign it to a group
• Holidays – Allows you to specify a specific date as a holiday. Used in conjunction with schedules.
Panel Setup
Location Settings From Panel Setup, scroll to Panel Programming. then

Date and Time Press Select. Select
Panel Programming
Panel Status
Panel Programming
603981210
Schedules The Panel Programming screen is displayed

Holidays
To avoid repeating the same steps for every function described in the following pages, the Panel Programming Sections assume you
have already navigated to the Panel Programming screen.
Schedules
On this set of screens, you assign and event to a group, and set one action for that event. For each event, you specify the time the
event occurs. You also specify whether the event will occur on a per day basis. Additionally, you specify whether the event will occur on
any day designated as a holiday.
Panel Programming
603981210
From the Panel Programming screen, highlight Select
Schedules
Holidays Schedules and press Select
Point to the desired Point the LMCT-100-2 at the infrared sensor on

Panel IR Sensor and
press ‘Select’ the LMRD board and press Select to open the Select
Program Schedule screen.
21
Program Schedule to move to each

Select the Event Number in which to store the or
parameter
Event Number: <1> schedule information. The Type determines the
Ty p e : <Normal Hours> action for the event. For details on the actions, see to change the value
or
Time: <07>:<00> the Schedules on page 7. Set the Time for the of the parameter
Group: <1> event to occur and assign the event to a Group. then choose
ACTIVE DAYS ACTIVE DAYS
DONE DELETE SEND Then, highlight ACTIVE DAYS and press Select.
and press Select
Schedule Active On For each day of the week, select whether the to move to each
or
event will be active (Yes or No). Additionally, select parameter
Mon: <Y> Tu e : <Y> whether the event will be active on holidays. (You
We d : <Y> Thu: <Y> to change the value
determine which days are holidays in the Holidays or
Fri: <Y> Sat: <N> of the parameter
Sun: <N> Holiday: <N> screen.)
then choose
Highlight DONE and press Select to return to the DONE and
DONE Program Schedule screen. press Select
Program Schedule Highlight SEND and press Select.

Event Number: <1> sensor on the LMRD board and press Select. You
Ty p e : <Normal Hours>
return to the Program Schedule screen, where
then
Time: <07>:<00> Select
Group: <1> you can program the next event
ACTIVE DAYS When finished, highlight DONE and press Select to
DONE DELETE SEND
return to the Panel Programming screen.
Holidays
On this screen, you determine which days are designated as holidays.
Panel Programming
603981210
From the Panel Programming screen, highlight then
Schedules
Holidays Holidays and press Select Select
Point to the desired Point the LMCT-100-2 at the infrared sensor on the
Panel IR Sensor and
press ‘Select’ LMRD board and press Select to open the Holiday Select
Setup screen.
For the Holiday parameter, select the memory

location to store the information. Then select the
Holiday Setup date for the holiday and Duration. to move to each
or
parameter
Holiday: <1> Highlight SEND and press Select.
Ye a r : <2014> to change the value
Once again, point the LMCT-100-2 at the infrared or
Month: <Jul> of the parameter
Date: <4> sensor on the LMRD board and press Select. You
Duration: <1 day> return to the Holiday Setup screen, where you can then choose
DONE DELETE SEND program the next event SEND and
press Select
When finished, highlight DONE and press Select to
Panel Status
This screen displays the date and time,based on the panel settings, sunrise/sunset times based on date and location settings, whether
the current date is a holiday, and the current settings of the dip switches. Additionally, it will display an error message for certain
problems.
22
Panel Setup
Location Settings then

Date and Time From Panel Setup, scroll to Status. Press Select . Select
Panel Programming
Panel Status
Panel IR Sensor and LMRD board and press Select.
press ‘Select’
Select
One of the following screens will display,
depending on the Status option you selected.
Panel Status Most fields on this screen are self explanatory. A

Nov 10, 2014 Mon value of “STD” indicates standard time and a value
15:19 STD Non-Holiday of “DST” indicates daylight savings time
Sunrise: 06:14 The Con LEDs field indicates errors, and will show
Sunset: 16:47
Con LEDs: 00000000 “1” in individual digits when the Config LED is lit
Dip Switch: 00000000 solid and not blinking. From left to right, the error
DONE categories are as follows:
• 1st and 2nd digits – not used
• 3rd digit – RTCLOCK
• 4th digit – SEEPROM Select DONE
• 5th digit – Bootload
• 6th digit – Power
• 7th digit – DLM Local Network
• 8th digit – Relay
Press Select to return to the Status screen.
For the Dip Switch field, a value of 1 indicates that
particular dip switch is set to ON. For details on
what each dip switch controls, see “Dip Switches”
on page 7.
Accessing Group Setup Options

Group Setup provides access to the following functions:
• Assign Loads to groups
• Set Occupancy Sensor behavior for groups
• Assign Dark/Light Events to groups
B AT =
Adjust Light Level
Global Network Navigate to the Group Setup option on the second then
Utilities main menu screen and press Select. Select
Panel Setup
Group Setup
More
WARNING:
LMBC or Panel must
be connected A warning appears, explaining that a bridge or
To a c c e s s panel is needed for this functionality. Press Select, Select
Group Setup then point the LMCT-100-2 at any IR enabled
device and press Select again..
Press ‘Select’
to proceed
23
Group Setup – LMBC
Group Loads This screen provides access to the three Group

Group Occ Sensors setup options. Navigate to the desired option and Select
Group Dark/Light press Select.
DONE
Group Loads
On this set of screens, you assign loads to groups and customize the behavior of those groups.
Group Loads From Group Setup,highlight Group Loads and Select

Group Occ Sensors press Select.
Group Dark/Light
DONE
Group Setup
to choose the
Group: <1+> or
Ty p e : <Custom+> Choose the Group number. Press Select to open Group number
the Group x Loads screen. then press
Select
DONE DELETE SEND
to move to each
or
Group 1 Loads To assign various loads to the group, scroll through parameter
each Load number and select whether that load to change the value
is a Member of that group. When complete, select or
Load: <1> of the parameter
DONE to return to the Group Setup screen. then choose
Member: < Ye s > DONE and
You also select have the option of using the
Smartwire function instead of manually scrolling press Select
DONE SMARTWIRE through the loads. To do this, select SMARTWIRE. OR
Select SMARTWIRE
P oint to any IR
enabled devic e and
press Selec t to Point the LMCT-100-2 at the infrared sensor on the Select
begin Smartwiring LMRD board and press Select
loads within the
P anel
Once you enter Smartwire mode, you can use

Add or Remov e lo ad s
by using the the Load buttons on the panel to assign the loads
push button n ext to to the group. See “Load Binding to Groups 1–8
each relay. W hen (Smartwire)” on page 16 for details. Note that
finished, poi nt to Select DONE
using this method, you can program groups higher
the IR device
and select e ither than #8 (up to group #99) with Smartwire. Once
DONE CANCEL finished, select DONE to return to the Group
Setup screen.
Select the Type field. Choose one of the
Group Setup to move to each
predefined macros or select “Custom+” to define or
the group behavior parameters. parameter
Group: <1+>
Ty p e : <Custom+> If choosing “Custom+”, press Select to open the to change the value
or
Group x Custom Parms screen. of the parameter
For details on the Macros, see “Macros” on page then choose
DONE DELETE SEND 12. If choosing a Macro, proceed to the last LOADS and
press Select
step in this section.
24
Group 1 Custom Parms to move to each

The Group x Custom Parms screen contains the or
Blink: <5 min> parameter
first five of the seven programmable parameters.
TDelay NH: <None> For definitions of these fields see “Groups, Scenes, to change the value
TDelay AH: <120 min> or
NH—> AH: < Tu r n O f f > Schedules, and Macros” on page 9. of the parameter
AH—> NH: <LNZ> Select NEXT to access the remaining two then choose
parameters. NEXTand
NEXT DONE press Select
Group 1 Custom Parms to move to each

or
Sensor Behavior parameter
AH: <On/Off> to change the value
NH: <On/Off> After setting the last two parameters, select DONE or
to return to the Group Setup screen. of the parameter
then choose
DONE and
PRIOR DONE press Select
Group Setup Highlight SEND and press Select. to move to each

or
Once again, point the LMCT-100-2 at the infrared parameter
Group: <1+> sensor on the LMRD board and press Select. You
Ty p e : <Custom+> to change the value
return to the Group Setup screen, where you can or
of the parameter
program the next group.
then choose
When finished, highlight DONE and press Select to LOADS and
DONE DELETE SEND press Select
return to the Group Setup Options screen.
Group Occupancy Sensors

On this set of screens, you assign individual events that determine whether loads assigned to a group will turn on or off, based on input
from an occupancy sensor.
NOTE: If using multiple occupancy sensors, when programming with the LMCT-100-2, you should only assign ONE sensor input to a
group. Assigning more than one sensor to a group will lead to inconsistent response (but you can assign different sensors to
different groups). If you need to assign multiple sensors to a group, use the LMCS software to program the actions. The LMCS
software has additional capabilities for programming input from multiple sensors.
Group Setup – Panel
Group Loads From Group Setup,highlight Group Occ Sensors Select

Group Occ Sensors and press Select.
Group Dark/Light
DONE
Point to the desired Point the LMCT-100-2 at the infrared sensor on

Panel IR Sensor and
press ‘Select’ the LMRD board and press Select to open the Select
OccSensor Event screen.
Occ Sensor Event

to change the value
Event Number: <1> or
Select the Event number in which to store the of the parameter
occupancy sensor event. Then highlight NEXT and then choose
press Select. NEXT and
press Select
NEXT DONE DELETE SEND
25
Select the number of the OccSensor assigned

to the event. Sensor numbers are automatically
assigned based on serial number with the highest
number set to 1, next highest set to 2, etc.
Set the Event Type to either “Group” or “Scene”.
Set the Occupied (sensor detects occupancy)
and Vacant (sensor detects vacancy). Depending
on whether you chose “Group” or “Scene”, the
possible values will change. For a scene, it will
Occ Sensor Event 1 be either “Scene On” or “Scene Off”. For a group, to move to each
or
<New Event> see “Occupancy Sensor Events for Groups” on parameter
OccSensor: <1> page 11 for a description of the values for these
E v e n t Ty p e : <Group> to change the value
parameters. or
Occupied: <LNZ> of the parameter
Va c a n t : < Tu r n O f f > NOTE: Whether the load responds to the sensor then choose
Group: <1> message is determined by the two sensor ACTIVE DAYS
ACTIVE DAYS DONE related parameters that are part of the and press Select
group. So, for example, if Sensor NH is
set to Manual On/Auto Off, the load will
respond to the Off Action but not the On
Action during Normal Hours.
The last parameter will change to be either Group
or Scene, depending on the value you chose for
Event Type. Select the group or scene that the
event is assigned to. Then, highlight ACTIVE
DAYS and press Select
For each day of the week, select whether to move to each
Occ Sensor Active On response to sensor input will be active (Yes or or
parameter
Mon: <Y> Tu e : <Y> No). Additionally, select whether the event will be
We d : <Y> Thu: <Y> active on holidays. (You determine which days are to change the value
or
Fri: <Y> Sat: <N> holidays in the Holidays screen.) of the parameter
Sun: <N> Holiday: <N> Highlight DONE and press Select to return to the then choose
DONE Occ Sensor Event x screen. Then select DONE DONE and
press Select
again to return to the OccSensor Event screen.
Occ Sensor Event Highlight SEND and press Select.
Event Number: <1> sensor on the LMRD board and press Select. You to choose
return to the Group Setup screen, where you can or SEND and
program the next group. press Select
return to the OccSensor Event screen.
Group Dark/Light
On this set of screens, you assign individual dark/light events.
Group Loads From Group Setup, highlight Group Dark/Light then

Group Occ Sensors and press Select. Select
Group Dark/Light
DONE
Panel IR Sensor and
press ‘Select’ LMRD board and press Select to open the Dark/ Select
Light Events screen.
26
Dark/Light Events
Event: <1> to change the value
or
Select the Event number in which to store the of the parameter
dark/light event. Then highlight NEXT and press then choose
Select to open the Dark/Light Event x screen. NEXT and
press Select
This screen changes depending on the value of

the Control parameter. By default, this is set to
“Astro”. In this case, the dark and light events
are determined by sunrise and sunset, which is
dependent on the values you set on the Location
Setup screen.
Set the Type to either “Group” or “Scene”.
Set the Dark and Light parameters. Depending
on whether you chose “Group” or “Scene”, the
possible values will change. For a scene, it will be
either “Scene On” or “Scene Off”. For a group, see
“Dark/Light Events” on page 12 for a description to move to each
Dark/Light Event 1 of the values for these parameters. or
Controller: <Astro> parameter
Ty p e : <Group> The Offset parameter determines when the event
Dark: <None> to change the value
will be triggered in relation to the actual sunrise or
Light: <None> and sunset time. A positive offset acts as if the time of the parameter
Offset: <-20min>
Group: <9> between sunrise and sunset was longer (more then choose
daytime), and a negative offset acts as if there ACTIVE DAYS
ACTIVE DAYS DONE and press Select
were less time between sunrise and sunset (less
daytime). So if you select -20 minutes, the Dark
event will trigger 10 minutes before sunset and the
Light event will trigger 10 minutes after sunrise.
See the chart on page 13 for more details of this
example.
The last parameter will change to either Group
or Scene, depending on the value you chose for
Event Type. Select the group or scene that the
event is assigned to.
Then, highlight ACTIVE DAYS and press Select.
(Skip ahead to the D/L Active Event ON screen.
If you change the Controller parameter to
“Photocel 1”, dark light events are instead
triggered by photocell sensor input. Although
multiple LMIN-104s or LMIO-301s may be
connected to the network, only a single one can be
programmed using the LMCT. Select the number
of the LMIN-104/LMIO-301 you wish to assign.
The LMIN-104 or LMIO-301 with the highest serial
number will have the lowest ID, and so on.
Dark/Light Event 1 Set the Type to either “Group” or “Scene”. to move to each
Control: < Ph o t o c e l 1 >
or
Once you select a value and scroll down to the parameter
Ty p e : <Group> next parameter, the screen changes. Two new
Dark: <LNZ> to change the value
parameters are displayed below Dark and Light. or
Light: < Tu r n O f f > of the parameter
Setpoint: <50fc> The Setpoint is the amount of foot candles that then choose
Delay: <2min> will determine when the Dark and Light events are ACTIVE DAYS
MORE DONE triggered. (When the light becomes brighter than and press Select
the Setpoint, it triggers the Light event, and when it
becomes darker, it triggers the Dark event.)
The Delay parameter sets the amount of time after
the Setpoint is reached that the event is actually
triggered. This helps prevent unwanted event
triggering, for example, when the light temporarily
gets darker because of a cloud passing over the
sun.
Select MORE to display the final parameter.
27
Dark/Light Event 1 to move to each

Group: <1>
or
The parameter on this screen will change to either parameter
Group or Scene, depending on the value you to change the value
chose for Event Type. Select the group or scene or
of the parameter
that the event is assigned to.
then choose
Then, highlight ACTIVE DAYS and press Select. DONE and
ACTIVE DAYS DONE press Select
For each day of the week, select whether the dark/ to move to each
D/L Event Active On light event will be active (Yes or No). Additionally, or
parameter
Mon: <Y> Tu e : <Y> select whether the event will be active on holidays.
We d : <Y> Thu: <Y> (You determine which days are holidays in the to change the value
or
Fri: <Y> Sat: <N> Holidays screen.) of the parameter
Sun: <N> Holiday: <N> Highlight DONE and press Select to return to the then choose
DONE Dark/Light Event x screen. Then select DONE DONE and
press Select
again to return to the Dark/Light Events screen.
Dark/Light Events Highlight SEND and press Select.
Event: <1> Once again, point the LMCT-100-2 at the infrared
sensor on the LMRD board and press Select. You to choose
return to the Dark/Light Events screen, where you or SEND and
can program the next event press Select
Utilities
The LMCT-100-2 contain a number of different Utilities. This section covers the Status utilities provide status information on loads and
groups, photosensors, and sensors connected to the panel.
An additional screen containing status information specific to panels is also available from the Panel Setup screen. See “Panel Status”
on page 22.
B AT =
Adjust Light Level
Global Network Navigate to the Utilities option on the second main then
Utilities menu screen and press Select. Select
Panel Setup
Group Setup
More
Utilities Menu
SmartWire
Identify Devices
Force System into PnG
Navigate to the Status option and press Select.
then
Room Mode Select
Load Shed
Status
Done
Status – Panel
Load Status
Group Status
Light Level Press Select to choose the Load Status option. Select
Occupancy Sensors
Done
28
Load Status
This set of screens displays details about each load in the panel, as well as any loads in connected room controllers.
The first screen indicates the on/off status of each

load. A value of “1” indicates it is ON. A value of “0”
indicates it is OFF. A value of “.” indicates no load
exists for that number.
The loads within the panel display first followed
Load 1 Status by loads from connected room controllers. In the
Load On: Select More or
example to the left, loads 1–24 are within the panel to select the
01 1111111111 10
11 1101101001 20 and load 25 is from an LMRC-101. desired load
21 11101 . . . . . 30 or
For additional details about the load, highlight that
31 . . . . . . . . . . 40 then press
load and press Select to open the Load x Online Select
41 . . . . . . . . . . 50
51 . . . . . . . . . . 60 screen. (If you try and select a number for which
there is no load, nothing happens.)
To return to the Status screen, scroll down past
the bottom row (51–60). A second screen displays
showing loads 21–64. Highlight DONE and press
Select.
The “1” indicates
a priority of 8.
Load 1 Online
This screen displays the BACnet priority of the load
1 2 3 4 5 6
. . . . . . DLM devices will typically have a priority of 8. Select
7 8 9 10 11 12 Highlight PROPERTIES and press Select.
. 1 . . . .
13 14 15 16
. . . .
PROPERTIES DONE
This screen indicates the current output of the load,

whether the load is a dimming or non-dimming
load. Mode indicates whether the load is currently
in Normal Hours or After Hours. Grace Timer
Load 2 Properties 1 indicates whether the load is currently counting
Output Level: 100% down between Normal Hours and After Hours,
L o a d Ty p e : NonDim during the Blink period.
Grace Timer: None Select
Mode: Normal Hours For details on the definitions of each parameter
Blink: 5 min value on this and the next two screens, see the
Load Settings section of the LMCT-100-2 User
NEXT DONE
Guide.
Highlight NEXT and press Select to see more
properties or select DONE to return to the Panel
Setup screen.
Load 2 Properties 2
This screen displays parameters related to the
TDelay NH: None transitions between Normal Hours and After Hours.
TDelay AH: 120 min Select
NH–>AH: Tu r n O f f Highlight NEXT and press Select to see more
AH–>NH: Do Nothing properties or select DONE to return to the Panel
Setup screen.
NEXT PRIOR DONE
Load 2 Properties 3
This screen displays the sensor behavior for this
Sensor Behavior
AH: Man On/Auto Off load.
Select DONE
NH: Auto On/Off Highlight DONE and press Select to return to the
Status screen.
PRIOR DONE
29
Group Status
This set of screens displays the loads that are assigned to the group, along with their current on/off state. Additionally, you can view the
settings for the group. Finally, in cases where the setting of an individual load are different from the group settings, you can view the
differences. This can be extremely helpful when trying to diagnose a situation in which a load is not responding as expected. Keep in
mind that individual loads can be programmed with different values from the group but still be a member of the group.
Status – Panel
Load Status
Group Status From the Status Menu, highlight the Group Status then
Light Level option and press Select. Select
Occupancy Sensors
Done
Group Status
to change the value
Group: <1> or
Select the Group number that you want to display, of the parameter
highlight NEXT, and press Select. then choose
NEXT and
press Select
NEXT DONE
Press
Select Point the LMCT-100-2 at the infrared sensor on the
Panel IR Sensor and LMRD board and press Select.
press ‘Select’
Select
One of the following screens will display,
depending on the Status option you selected.
This screen indicates which loads are assigned

to the group, along with the on/off status of each
load. A value of “1” indicates it is ON. A value of “0”
indicates it is OFF. A value of “.” indicates the load
is not assigned to the group.
On the top line, the Status will display “Off” if all
assigned loads are off, “100%” if all loads are on
Group 1 Status Mixed and there is no dimming, and “Mixed” if some loads
Load 5 Parms Not Same or
are on and others are off. If all loads in the group to select the
0 1 1 1 .0 1 . . . . . 1 0
11 11 . . . . . . . 1 20 dim and are set to the same dimming amount, it desired load
21 . . 101 . . . . . 30 will display that amount. or
31 . . . . . . . . . . 40 then press
Move the cursor to highlight a specific load. If you Select
41 . . . . . . . . . . 50
51 . . . . . . . . . . 60 scroll down below the line for 51–60, you will see
loads 61–64.
The load number will display in the second line.
The Parms parameter will say either “Same” if
the load parameters match the group parameters,
or “Not Same” if there is a difference. To view the
difference, press Select to open the Actual Load x
Parms 1 screen
Actual Load 5 Parms1 The screen displays the values of the first five
Blink: 5 min parameters assigned to the individual load.
to choose the
TDelay NH: None To view the sensor parameters, highlight MORE or
TDelay AH: 120 min option
and press Select.
NH–>AH: Tu r n O f f then press
AH–>NH: Tu r n O n To compare the values on this screen with the Select
values for the group, highlight GROUP PARMS
MORE GROUP PARMS DONE and press Select.
Actual Load 5 Parms2 The screen displays the values of the sensor
parameters assigned to the individual load.
to choose the
Sensor Behavior To return to the original 5 parameters, highlight or
AH: Man On/Auto Off option
MORE and press Select.
NH: Auto On/Off then press
To compare the values on this screen with the Select
values for the group, highlight GROUP PARMS
MORE GROUP PARMS DONE and press Select.
30
The screen displays the values of the first five

parameters assigned to the group.
Group Load 5 Parms1 In this example, if you compare the Blink
Blink: 10 min parameter to the one on the Actual Load screen, to choose the
TDelay NH: None you will see the group value is 10 minutes, while or
TDelay AH: 120 min option
the individual load is 5 minutes.
NH–>AH: Tu r n O f f then press
AH–>NH: Tu r n O n To view the sensor parameters, highlight MORE Select
and press Select.
MORE LOAD PARMS DONE To compare the values on this screen with the
values for the individual load, highlight LOAD
PARMS and press Select.
The screen displays the values of the sensor
parameters assigned to the individual load.
Group Load 5 Parms2 To return to the original 5 parameters, highlight
MORE and press Select. to choose the
Sensor Behavior or
AH: Man On/Auto Off To compare the values on this screen with the option
NH: Auto On/Off values for the group, highlight GROUP PARMS then press
and press Select. Select
MORE LOAD PARMS DONE Once you finish comparing the values, highlight
DONE and press Select to return to the Status
screen
Light Level
This screen displays the current light level, in foot candles, registered by an LMIO-301 with an attached photosensor.
Status – Panel
Load Status
Group Status From the Status Menu, highlight the Light Level then
Light Level option and press Select. Select
Occupancy Sensors
Done
The top line of the display shows the number of

301 1 of 2 Level LMIO-301s connected to the network. The display
MAC: 0373303229
shows the light level of a single device. The second Select NEXT
Light Level: 1 fc line shows the serial number (MAC address) of the
currently displayed device. OR
Highlight NEXT and press Select to view the light Select DONE
NEXT PRIOR DONE level of another photosensor. Or select DONE to
return to the Status screen.
Occupancy Sensor Status

This screen display current values of occupancy sensors attached to the network.
Status – Panel
Load Status
Group Status From the Status Menu, highlight the Occupancy then
Light Level Sensors option and press Select. Select
Occupancy Sensors
Done
31
The top line of the display shows the number of

occupancy sensors connected to the network. The
display shows the values for a single occupancy
sensor. The second line shows the serial number
(MAC address) of the currently displayed device.
Status indicates whether the sensor is currently
found on the network. (When a sensor is
connected, it is stored in memory until the panel
is reset. So, if the sensor is disconnected and the
OccSen 1 of 4 Stat panel has not been reset, the status will display
MAC: 0209715204
“Offline”.) Select NEXT
Status: Online State indicates whether the sensor currently is set
State: Occupied as occupied or unoccupied. OR
L o a d Tr a c k i n g : Ye s Select DONE
If Load Tracking is “Yes”, loads bound to the
NEXT PRIOR DONE sensor will respond, based on the programming
settings for the sensor and group. If it is set to “no,
then the loads will not respond to the sensor. This
is used in situations where the panel is connected
to a BAS or other BACnet device and you want to
use the sensor to monitor occupancy/vacancy for
purposes other than turning loads on or off.
Highlight NEXT and press select to view the values
of additional photosensors. Or select DONE to
return to the Status screen.
CONNECTING MULTIPLE LMCP PANELS IN A NETWORK

The LMCP can connect to other LMCP panels via BACnet, using the MS/TP connections. Connecting panels to each other via BACnet
allows them to share common group numbers for schedules or switches. This provides the ability to program a common behavior for an
entire building or section of a building, via LMCS-100 software
One or more LMCPs can also be connected to other devices in a Building Automation System (BAS) using BACnet. This provides
for connection to a Segment Manager or other supervisory system. The BACnet settings can be configured using the LMCT-100-2
controller or LMCS-100 software.
BACnet Settings
The following parameter settings and concepts are important to understand when configuring the LMCP for BACnet communication:
• Device ID – The device ID is a unique number, between 0 and 4194302, that identifies a device in a BACnet network. Every device
in the network must have a different number. By default, the LMCP uses the last 6 digits of the serial number (plus a leading 0 to
complete the seven digit number). This number can be changed if needed, for example, when required by an integrator, as part of a
BAS. Once set, the LMCP will remember the ID number even if other parameters are reset to their default values.
• Device Name – This is a label for the panel, useful when working with LMCS in a situation where multiple panels are used, to help
more easily distinguish between the panels. Any numerals or letters can be used in naming the panel. By default, the name is the
same as the serial number. The name can be programmed using either LMCS, the LMCT-100-2, or a BAS application.
• MS/TP MAC Address – The MS/TP MAC address is an additional identifier, used by the devices on the network to communicate
with each other. It is a number between 0 and 127. It is important to understand the difference between the device ID and the MS/
TP MAC Address. The Device ID is, in essence, a number that identifies “who” the devices is, while the MS/TP MAC address
identifies its “location”.
In a BACnet network, all the devices pass a token to each other to determine which device has control of communication over
the network. The MS/TP MAC address is used to “locate” other devices. When a device receives the token, it will take control of
the communication and send messages to other devices as needed. It then passes the token to the device with the next highest
MS/TP MAC address. In order to do this, it sends an “Are you there?” message on the MAC address one higher than its own. If it
receives a response, it passes the token. If it does not receive a response, it tries again on the next highest number, continuing in
this manner until it receives a response. This “Are you there?” message is referred to as a Poll For Master.
NOTE: In order to send and respond to this Poll For Master message, a device must be designated as a master device. Other
devices (slave devices) on the network will not respond, and cannot take control of the communication.
While the Device ID is fixed and should not change, the MS/TP MAC address can change as devices come on or drop off the
network. By default, the LMCP will automatically assign an MS/TP MAC address. When the LMCP is powered up, it will check
the network for other devices to determine if its current MAC address is being used by another device. If, not it will keep the same
address, but if it is, and will assign an unused number between 32 and 127.
You can manually assign an MS/TP MAC address instead of having the LMCP automatically assign the number. This can be
useful, especially in larger networks where response time is important. Since the Poll For Master message checks the next highest
address number and then increments that number until it finds a device, having devices with gaps between numbers can increase
latency. If you have 10 devices, numbered 0–9, you will have optimal performance since no time is wasted sending the Poll For
Master message to an unused number.
32
• Max Master – The Max Master parameter is another parameter that will cut down on latency. The value you set for this parameter
is the highest number the LMCP will check when sending a Poll For Master message, before returning to 0. So, in the previous
example, where there are 10 devices numbered 0–9, if you set the Max Master to 9, it will never check addresses 10–127.
NOTE: If using the LMCP with a global controller such as a router, BAS or Segment Manager, the global controller will always
default to a MAC address of 0.
NOTE: You should be aware that devices connected over the DLM Local Network also have MAC addresses for communication
purposes, but that MAC address is entirely separate from the MS/TP MAC address.
Further details on Device IDs and MAC addresses can be found in WattStopper’s Technical Bulletin #180 at http://www.wattstopper.com/
resources/download-center/tech-bulletins-whitepapers.aspx.
Examples of Using the LMCP in a BACnet Network

The following three examples demonstrate applications for connecting the LMCP to a BACnet network:
Two or more LMCP panels connected to each other without a Segment Manager or BAS
This is the simplest configuration. Remember that when a relay is assigned to a group, if more than one panel uses the same group
number, those relays in the different panels will respond to any events or controllers that affect that group. While this can provide an
easy way of controlling relays in multiple locations, if that is not what you want, make sure to use different group numbers in different
panels.
When connecting the panels via the MS/TP jack, keep in mind that the general rules for BACnet MS/TP apply. This includes termination
quality, polarity of the dataline, maximum network physical length, usage of repeaters/isolators, usage of proper dataline (LM-MSTP and
LM-MSTP-DB only), etc.
One or more LMCP panels connected to an LMJA-8125-AX or LMJA-8300-AX Network Controller
Best practice rules for connecting panels to a Segment Manager can be found in technical bulletin #189. Wiring information, including
termination quality and polarity are discussed in technical bulletin #179.2. These technical bulletins can be found at
http://www.wattstopper.com/resources/download-center/tech-bulletins-whitepapers.aspx.
The critical issue to keep in mind when using a Segment Manager is that you should normally use only the LMCP or the Segment
Manager to control scheduled events, since these events are associated with groups. The group related control messages sent from the
Segment Manager (see Appendix A) have the same priority as LMCP native schedules. Therefore, the group will always respond to the
most recently received event, and Segment Manager schedules and LMCP schedules can conflict with each other.
Utilizing LMCS-100 allows for programming intricate coordinated behaviors, where either the LMCP or Segment Manager schedules
can take precedence under certain circumstances, but this requires detailed understanding of the BACnet priority array and of LMCS
configuration, and is not normally recommended.
Additionally, similar to the way in which a load can be programmed individually and still be part of a group, and so that the group setting
is applied when the group information is sent to the LMCP, you can send a message from the Segment Manager that will change a
setting for a device that is part of a group, and the group setting will not revert to the group value until the group information is sent again
to the LMCP by the LMCT-100-2 or LMCS-100.
One or more LMCP panels connected directly to the front end systems configured by an integrator/BAS technician
When connected to a BAS application, the LMCP can provide a variety of status messages. The LMCP (and other devices connected
via the DLM Local Network) can also respond to a variety of command messages. ”Appendix A” on page 35 lists the objects used for
communication with the LMCP.
33
BACnet Connectivity Scenarios
Addressing shown using optimized Optional connection

Device IDs and Mac addresses. to LMCS-100
Default IDs and Auto MAC addressing software.
can be used as desired, but sequential
addresses can optimize performance Must match UDP
if needed. port# of any
routers
LMCP Panels Optional connection

NB-Router
ID: 86001 ID: 86002 ID: 86003 to Segment Manager
MAC: 01 MAC: 02 MAC: 03 Connect via MS/TP or IP
ID: 1000
MAC: 00
LMSM
Network Number = 1000
Each of these are valid

Segment Networks
LMCP Panels
ID: 86004 ID: 86005 ID: 86006 ID: 86007 ID: 86008
MAC: 04 MAC: 01 MAC: 06 MAC: 07 MAC: 08
Network Number = 1001 (if a router were added)
The Device ID’s of this BACnet Segment Network are unique so that it could be combined
with the top network if desired. Combining Segment Networks is done using NB-ROUTERs
that must then assign a network number to each Segment Network.
34
APPENDIX A
BACnet Objects
NOTE: While there are 96 object instances available for many of the objects listed below, keep in mind that the LMCP panel supports
only 48 devices per network (A & B), and the panel itself is one of the devices in each network. Therefore, there is never a case
where you would use all 48 instances of an object in a single network.
Object Instance Object Alias Object Function

Device/Group Specific Control Objects
BO1–BO64 Loads 1–64, state Relay state, internally linked to the Analog Output objects by the trip
point parameter. Relay is ON above trip point and OFF below trip point.
Default trip point is 50% for LMRC-100 Series room controllers and 1%
for LMRC-200 and -300 Series room controllers.
AO1–AO64 Loads 1–64, level Dimming level, internally linked to the Binary Output objects by the trip
point parameter. Range = 0 to 100%.
AV1–AV96 Wattage Calculated based on the input voltage and measured current for room
controller 1 to 96. This only provides a valid reading if LMCS is used to
configure the “Baseline Wattage” values of all the panel’s relays. The
panel has no Current Transformers so this reading is also subject to
those loads operating correctly. If no full duty baseline power values
are configured, this value is calculated as AV501 * AV401 when any
one relay is active.
AV2-96 will only exist if any LMRCs or LMPLs or LMFCs are present
on the CAT5 networks A or B.
AV401–496 Input Voltage Per room controller, written by the user, default is 0.
AV402–496 will only exist if any LMRCs or LMPLs or LMFCs are
present on the CAT5 networks A or B.
AV501–596 Electrical current Read total current flowing through the room controller in amps, for
room controller 1 to 96.
AV502–596 will only exist if any LMRCs or LMPLs or LMFCs are
present on the CAT5 networks A or B.
AV101–AV196 Occupancy sensor 1–96, time delay For occupancy sensor 1 to 96, 0 to 30 minutes.
AV201–AV296 Occupancy sensor 1–96, PIR sensitivity Per PIR (passive infrared) sensor, 0 to 100% in percent, 10%
resolution.
AV301–AV396 Occupancy sensor 1–96, ultrasonic Per ultrasonic sensor, 0 to 100% in percent, 10% resolution.
sensitivity
AI1–AI96 Exterior photocell Daylight level as read by LMIO-301 photocell input module 1 to 96.
AI4001–AI4096 Daylight sensor 1–96, light level Interior footcandle level as read by LMLS-400 daylight sensor 1 to 96.
AI5001–AI5096 Daylight sensor 1–96, light level Interior footcandle level as read by LMLS-500 daylight sensor 1 to 96.
AV4101–AV4196 Daylight sensor 1–96, ramp up rate For LMLS-400 daylight sensor 1 to 96, ramp up rate. Default is 20%
per second, writable in the range of 1% to 100 % per second.
AV4201–AV4296 Daylight sensor 1–96, day setpoint For LMLS-400 daylight sensor 1 to 96, day setpoint. Default is 50
footcandles, writable in the range of 1 to 255 footcandles.
AV4301–AV4396 Daylight sensor 1–96, night setpoint For LMLS-400 daylight sensor 1 to 96, night setpoint. Default is 10
footcandles, writable in the range of 2 to 255 footcandles.
AV4401–AV4496 Daylight sensor 1–96, off time delay For LMLS-400 daylight sensor 1 to 96, off time delay. Default is 10
minutes, writable in the range of 3 to 30 minutes.
AV4501–AV4596 Daylight sensor 1–96, on setpoint For LMLS-400 daylight sensor 1 to 96, on setpoint. Default is 7.5 foot-
candles, writable in the range of 1 to 3000 footcandles.
AV4601–AV4696 Daylight sensor 1–96, off setpoint For LMLS-400 daylight sensor 1 to 96, off setpoint. Default is 11.25
foot-candles, writable in the range of 1.5 to 6000 footcandles.
AV5101–AV5196 Daylight sensor 1–96, zone 1 setpoint For LMLS-500 daylight sensor 1 to 96, target setpoint for zone 1.
Writable in the range of 1 to 200 footcandles.
AV601–AV664 Loads 1–64, demand response cap Maximum dimming level for load during a demand response (shed)
level event. 100 = disabled.
35
Object Instance Object Alias Object Function
BI101–BI9608 Button state Read button state for 1 to 8 buttons per switch for 1 to 96 switches.
BI1–BI96 Detection state Occupancy sensor detection state. Active = occupied.
BV101–196 Switch lock status Read switch status (locked or unlocked).
Active = locked.
BV201-299 Group Normal Hours/After Hours Normal Hours/After Hours selection for a group.
Active = after hours.
MV4001–MV4096 Daylight sensor 1–96, operating mode For LMLS-400 daylight sensor 1–96, operation mode:
1 = ON/OFF, 2 = bi-level, 3 = tri-level, 4 = dimming.
MV4101–MV4196 Daylight sensor 1–96, setpoint multiplier For LMLS-400, off setpoint multiplier: 1=1.25x, 2=1.50x, 3=1.75x, 4=2x.
Room Level Control Objects
BV1 Schedule state Normal hours/after hours selection. Active = after hours.
NOTE: This changes the status for the entire panel, and therefore can
conflict with BV201-299, if not used carefully.
BV2 Switch lock control Lock or unlock enabled switches. Active = lock.
NOTE: This changes the switch lock status for every switch connected
to the panel, and therefore can conflict with BV101-196, if not
used carefully.
BV3 Room occupancy status Read occupancy status (occupied or unoccupied).
Active = occupied.
NOTE: This is the logical OR of the states of ALL sensors connected
to the panel regardless of their local control scheme. In other
words, if any sensor has a status of occupied, this value will
read occupied.
BV4 Force all loads ON Active = all loads ON at priority 1. Inactive = relinquish at 1 and ON at
priority 8.
NOTE: This will force all loads connected to the panel ON.
BV5 Force all loads OFF Active = all loads OFF at priority 2. Inactive = relinquish.
NOTE: This will force all loads connected to the panel OFF.
MV1 Scene control Write scene selection. Range = 1 to 16.
MV2 Demand response (shed) control Activate room level DR mode: 1 = no shed, 2 = shed mode, permit
switch override, 3 = shed mode, prohibit switch override.
NOTE: This will affect all loads connected to the panel.
AV901 MS/TP MAC address Default is 255 for automatic, writable in the range of 0 to 127.
AV902 MS/TP network speed Baud rate: 9600, 19200, 38400, 57600, 78600, 115200.
AV903 Input room size Allows user to write area in square feet from 0 to 65,534, default is 0.
AV904 Room lighting watts Read total lighting wattage for room.
Total of baseline watts for active relays, or if no baseline wattage for
the relays are used, then this is calculated as AV401 * AV501 + any
usage from LMRC/LMFC connected via CAT5 to the panel.
NOTE: This does not include used from LMPLs. Use AV906 for plug
load controllers.
AV905 Room watts/sq.ft. Read total room lighting W/ft2.
If the input room size for the entire application area is used and the
baseline watts method or AV401 * AV501 method is used, then this
object will calculate the aggregate watts per square foot of the whole
panel’s application area.
Use of this object is not recommended for use in applications where
panels cover mixed areas.
AV906 Room plug load watts Read total plug load wattage for LMPLs connected to the panel.
36
WARRANTY INFORMATION INFORMATIONS RELATIVES À LA GARANTIE INFORMACIÓN DE LA GARANTÍA
Wattstopper warranties its products to be free Wattstopper garantit que ses produits sont Wattstopper garantiza que sus productos
of defects in materials and workmanship for a exempts de défauts de matériaux et de fabrication están libres de defectos en materiales y mano
period of five (5) years. There are no obligations pour une période de cinq (5) ans. Wattstopper de obra por un período de cinco (5) años. No
or liabilities on the part of Wattstopper for ne peut être tenu responsable de tout dommage existen obligaciones ni responsabilidades por
consequential damages arising out of, or in consécutif causé par ou lié à l’utilisation ou parte de Wattstopper por daños consecuentes
connection with, the use or performance of this à la performance de ce produit ou tout autre que se deriven o estén relacionados con el
product or other indirect damages with respect dommage indirect lié à la perte de propriété, de uso o el rendimiento de este producto u otros
to loss of property, revenue or profit, or cost of revenus, ou de profits, ou aux coûts d’enlèvement, daños indirectos con respecto a la pérdida
removal, installation or reinstallation. d’installation ou de réinstallation. de propiedad, renta o ganancias, o al costo
de extracción, instalación o reinstalación.
No. 24811 – 06/24 rev. 6
© Copyright 2024 Legrand All Rights Reserved.

© Copyright 2024 Tous droits réservés Legrand. 800.879.8585
© Copyright 2024 Legrand Todos los derechos reservados. www.legrand.us/wattstopper

Manual de Usuario

Uploaded by

Copyright:

Available Formats

Manual de Usuario

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Manual de Usuario

Uploaded by

Copyright:

Available Formats

Wattstopper ®

Relay Panel Interiors

No: 24811 – 06/24 rev. 6

Catalog Numbers • Les Numéros de Catalogue • Números de Catálogo: LMCP8-10V/LMCP24-10V/LMCP48-10V

WARNING: The DB9 cables cannot be plugged in or unplugged

Features and Basic Terminology

Figure 2a: LMCPx – Switching Panel

Override Buttons and Status LEDs 1–6

Power Indication LED

DB9 Jack – For connection to LMPI

12/8 Jumper – For configuring whether the

Service LED – Blinks once per second if

Override Buttons and Status LEDs 7-12

Relay Override Buttons –Toggle relay ON or OFF depending

Remote Override Terminal (available on switching LMRD

DB9 Jack – For connection to LMPI card

Service LED – Blinks once per second if

Figure 3a: LMPI Circuit Board rev 7

Microcontoller activity indication LEDs (2 blue). The

Room Bus Network Communication Activity

1-4: Not currently used

Figure 3b: LMPI Circuit Board rev3

J11 – 511 ohm J12 – 511 ohm J13 – 120 ohm

Connecting Panels to Other DLM Devices, and Panels to Panels

Connecting Override Switches Directly to a Panel

Group Settings vs. Individual Relay Settings

Schedule Type Action Description

Astronomical Dark/Light Switching

Time ~Noon -20 30

Less Offset More Offset More Offset Less Offset

Example: Dallas Astro on 2/9/15

Switching Based on Input From an LMIO-301 or LMIN-104 and Photocell

Accessory Device Support

Using the LMIN-104 to Interface with Third Party Devices

Room Plug Load

LMCP-24 Maximum # of connected devices per network: 48 (including 1 for LMCP),

Maximum number of loads, including those in the panel, and on both

Maximum of 4 LMRC-10x or LMPL-101 allowed in a network. In this

102 102 102 213 212 213 101

Load Control Arbitration

PROGRAMMING THE LMCP

Load Binding to Groups 1–8 (Smartwire)

PROGRAMMING USING THE LMCT-100

Configuring the Network Settings

B AT = Scroll Down or Up to Highlight More, then press

Point to the desired

Network Settings The Panel Network screen opens, with Network

The top line of the screen shows the serial number

Network Settings From the Panel Network screen, scroll down to

The Network Status will display as “Unhealthy”

Accessing Panel Setup

Display Description Press

Point to the desired

Setting the Panel Location

Point to the desired

Select the desired State, and City. The Latitude/

Setting the Date and Time

Point to the desired

Depending on whether you choose a value of