Genshin Impact

Aqua Simulacra
Ready to print pattern (A4 size)
Length: 130cm Approx.
# Recommendation
It is recommended to print without margins(border-less) or print with same margin for all pages,
borderless for best result.

1. Recommended setting for printer (Canon G2010)

- Set Page Sizing & Handling to Actual size in printer setting.
- Click properties in printer setting
- In Quick Setup tab, set Printer Paper size to A4.
- Check the Borderless Printing in Additional Features.
- In Page Setup tab, select “Borderless” for page layout.
- Make sure there is no enlargement is set on the Amount of Enlarge slider. (Drag the slider to the most left)

Note:
-Recommended settings mention above are for (Canon G2010), print with A4 size paper 210mm x 297mm (8.27inches x 11.69inches) only.
-Setting page may vary from printer to printer. It is recommended to print at printing shop if you not sure how to configure your printer setting.

2. Recommended crafting materials such as Eva foam, acrylic and sort of can be purchased from most of
the craft supplies shop or stationery shop.
In case it is not available in your area, we will suggest you to get it thru online shop such as Amazon, Alibaba, Ebay or
any other shop which is comfortable for you.

Pattern pages : 35
Pattern design by NATA Cosplay and Crafts
Pattern designed by NATA Cosplay and Crafts only listed and sold @Etsy.com. Any other platform selling pattern designed by us is not genuine and not approved by us.
We do not hold any responsibility of your creditentials leak or scam as a result of buying from suspicious platform.
We hold the right not to entertain any inbox or message that has no purchase record from Etsy.com
Personal Use Only. This material does NOT contain any re-sale or re-distribution rights.
Guide
Sand edge mark with “ ” to double bevel edge
Guide
Sand edge mark with “ ” to double bevel edge
Sand edge mark with “ ” to full bullnose
Guide
Sand edge mark with “ ” to double bevel edge

2nd layer - Side A

Recommended
2mm Eva foam
stack on Base layer - Side A
*sand the edge mark with “=”
to double bevel edge
after stack on base layer
 lightly indent using
craft knife or ruler
along the orange line

Base layer - Side A

Recommended
5mm Eva foam x 4 stacks or
10mm Eva foam + (5mm Eva foam x 2 stacks)
cut along the outer line
Recommended
5mm Eva foam
attach with transparent string

Guide
Sand edge mark with “ ” to double bevel edge
Sand edge mark with “ ” to full bullnose
 blue line indicate
masking guide for paint job

Part J - Side A
Recommended
2mm Eva foam
stack on Base layer - Side A

Guide
Sand edge mark with “ ” to double bevel edge
Sand edge mark with “ ” to full bullnose
Part P - Side A Part R - Side A
Recommended Recommended
3mm Eva foam 3mm Eva foam
1. cut along the red line 1. cut along the red line
2. cut a V groove at the back 2. cut a V groove at the back
along the dotted line along the dotted line
and fill in fast glue and fill in fast glue

Part Q - Side A
Recommended
3mm Eva foam
1. cut along the red line
2. cut a V groove at the back
along the dotted line
and fill in fast glue

Build guide for Part P, Q and R

*no cut out required

glue below P
R

P
insert into the clevage on P and glue

Q
 blue line indicate
masking guide for paint job

blue line indicate

masking guide for paint job

blue line indicate

masking guide for paint job

Guide
Sand edge mark with “ ” to full bullnose
blue line indicate
masking guide for paint job
Guide
Sand edge mark with “ ” to double bevel edge
Sand edge mark with “ ” to full bullnose
 blue line indicate
masking guide for paint job

Part D -Side A
Recommended
2mm Eva foam
stack on Base layer - Side A

2nd layer -Side A

Recommended
8mm Eva foam or
10mm Eva foam
stack on Base layer - Side A

blue line indicate

masking guide for paint job

blue line indicate

masking guide for paint job
 Guide
Sand edge mark with “ ” to double bevel edge

blue line indicate

masking guide for paint job
 Build guide for base layer
*no cut out required

Recommended
9mm or 10mm rod as bone
cut a space on inner layer of base layer to house the bone
 Guide
Sand edge mark with “ ” to full bullnose

blue line indicate

masking guide for paint job
Guide
Sand edge mark with “ ” to double bevel edge
Guide
Sand edge mark with “ ” to double bevel edge
Sand edge mark with “ ” to full bullnose
Guide
Sand edge mark with “ ” to double bevel edge
 lightly indent using
craft knife or ruler
along the orange line

Base layer - Side B

for reference and masking purpose
*no cut out required

Guide
Sand edge mark with “ ” to double bevel edge
Sand edge mark with “ ” to full bullnose
 Guide
Sand edge mark with “ ” to double bevel edge

2nd layer - Side B

Recommended
2mm Eva foam
stack on Base layer - Side B
*sand the edge mark with “=”
to double bevel edge after
stack on base layer
 Part R - Side B Part P - Side B
Recommended Recommended
3mm Eva foam 3mm Eva foam
1. cut along the red line 1. cut along the red line
2. cut a V groove at the back 2. cut a V groove at the back
along the dotted line along the dotted line
and fill in fast glue and fill in fast glue

Part Q - Side B
Recommended
3mm Eva foam
1. cut along the red line
2. cut a V groove at the back
along the dotted line
and fill in fast glue

Build guide for Part P, Q and R

*no cut out required

glue below P
R

P
insert into the clevage on P and glue

Q
blue line indicate
masking guide for paint job

Part J - Side B
Recommended
2mm Eva foam
stack on Base layer - Side B

Guide
Sand edge mark with “ ” to double bevel edge
Sand edge mark with “ ” to full bullnose
 blue line indicate
masking guide for paint job

Guide
Sand edge mark with “ ” to double bevel edge
Sand edge mark with “ ” to full bullnose
 blue line indicate
masking guide for paint job

blue line indicate

masking guide for paint job

blue line indicate

masking guide for paint job

Guide
Sand edge mark with “ ” to full bullnose
Guide
Sand edge mark with “ ” to double bevel edge

blue line indicate

masking guide for paint job
 blue line indicate
masking guide for paint job

Part D -Side B
Recommended
2mm Eva foam
stack on Base layer - Side B

2nd layer -Side B

Recommended
8mm Eva foam or
10mm Eva foam
stack on Base layer - Side B

blue line indicate

masking guide for paint job

blue line indicate

masking guide for paint job
Guide
Sand edge mark with “ ” to full bullnose

blue line indicate

masking guide for paint job
Guide
Sand edge mark with “ ” to double bevel edge
 Part L
Recommended
3mm Eva foam

blue line indicate blue line indicate

masking guide for paint job masking guide for paint job

glue area shaded

in grey together

Part E
lightly indent using
craft knife or ruler
Recommended
along the orange line 5mm Eva foam
wrap on base layer

glue

Part H
Recommended
3mm Eva foam
wrap on the base layer

glue
Guide
Bevel cut edge mark with “ ”

Part B
Recommended
3mm Eva foam

glue
 Part A
Recommended
3mm Eva foam

glue

Guide
Bevel cut edge mark with “ ”
 Part G
Guide
Bevel cut edge mark with “ ” Recommended
2mm Eva foam

glue

glue

blue line indicate blue line indicate

masking guide for paint job masking guide for paint job

Part K
Recommended
3mm Eva foam

glue
Guide
Bevel cut edge mark with “ ”

Part M
Recommended
3mm Eva foam

glue

blue line indicate

masking guide for paint job
Guide
Bevel cut edge mark with “ ”

glue
 Part N
Recommended
5mm Eva foam

pink line indicate pink line indicate

masking guide for paint job masking guide for paint job

Guide
Bevel cut edge mark with “ ”
Guide
Bevel cut edge mark with “ ”

blue line indicate blue line indicate

masking guide for paint job masking guide for paint job
glue
*avoid apply glue
on the edge shaded
in red
 glue to the edge
of base layer
Part O
blue line indicate
Recommended blue line indicate
masking guide for paint job 3mm Eva foam masking guide for paint job
Part C
Recommended
10mm Eva foam

glue

Guide
Sand edge mark with “ ” to double bevel edge
Sand edge mark with “ ” to full bullnose
Bevel cut edge mark with “ ”