Liquid Penetrant Testing

Liquid penetrant testing is one of the oldest and simplest NDT methods where its
earliest versions (using kerosene and oil mixture) dates back to the 19th century. This
method is used to reveal surface discontinuities by bleedout of a colored or fluorescent
dye from the flaw. The technique is based on the ability
of a liquid to be drawn into a "clean" surface
discontinuity by capillary action. After a period of time
called the "dwell time", excess surface penetrant is
removed and a developer applied. This acts as a blotter
that draws the penetrant from the discontinuity to reveal
its presence.
The advantage that a liquid penetrant inspection offers over an
unaided visual inspection is that it makes defects easier to see for the
inspector where that is done in two ways:
 It produces a flaw indication that is much larger and easier for
the eye to detect than the flaw itself. Many flaws are so small
or narrow that they are undetectable by the unaided eye (a
person with a perfect vision can not resolve features smaller
than 0.08 mm).
 It improves the detectability of a flaw due to the high level of
contrast between the indication and the background which helps
to make the indication more easily seen (such as a red indication
on a white background for visable penetrant or a penetrant that
glows under ultraviolate light for flourecent penetrant).

Liquid penetrant testing is one of the most widely used NDT methods. Its popularity
can be attributed to two main factors: its relative ease of use and its flexibility. It can
be used to inspect almost any material provided that its surface is not extremely rough
or porous. Materials that are commonly inspected using this method include; metals,
glass, many ceramic materials, rubber and plastics.
However, liquid penetrant testing can only be used to inspect for flaws that break the
surface of the sample (such as surface cracks, porosity, laps, seams, lack of fusion, etc.).

Introduction to Non-Destructive Testing Techniques Instructor: Dr. Ala Hijazi

Liquid Penetrant Testing Page 1 of 20

These materials have been adapted from https://www.nde-ed.org and are reused with permission.
Steps of Liquid Penetrant Testing
The exact procedure for liquid penetrant testing can vary from case to case depending
on several factors such as the penetrant system being used, the size and material of
the component being inspected, the type of discontinuities being expected in the
component and the condition and environment under which the inspection is
performed. However, the general steps can be summarized as follows:
1. Surface Preparation: One of the most critical steps of a liquid penetrant testing is
the surface preparation. The surface must be free of oil, grease, water, or other
contaminants that may prevent penetrant from entering flaws. The sample may
also require etching if mechanical operations such as machining, sanding, or grit
blasting have been performed. These and other mechanical operations can
smear metal over the flaw opening and prevent the penetrant from entering.

2. Penetrant Application: Once the surface has been thoroughly cleaned and dried,
the penetrant material is applied by spraying, brushing, or immersing the part in
a penetrant bath.

3. Penetrant Dwell: The penetrant is left on the surface for a sufficient time to
allow as much penetrant as possible to be drawn or to seep into a defect.
Penetrant dwell time is the total time that the penetrant is in contact with the
part surface. Dwell times are usually recommended by the penetrant producers
or required by the specification being
followed. The times vary depending
on the application, penetrant
materials used, the material, the form
of the material being inspected, and
the type of discontinuity being
inspected for. Minimum dwell times
typically range from 5 to 60 minutes.
Generally, there is no harm in using a longer penetrant dwell time as long as the
penetrant is not allowed to dry. The ideal dwell time is often determined by
experimentation and may be very specific to a particular application.

4. Excess Penetrant Removal: This is the most delicate step of the inspection
procedure because the excess penetrant must be removed from the surface of
the sample while removing as little penetrant as possible from defects.

Introduction to Non-Destructive Testing Techniques Instructor: Dr. Ala Hijazi

Liquid Penetrant Testing Page 2 of 20

These materials have been adapted from https://www.nde-ed.org and are reused with permission.
 Depending on the penetrant system used,
this step may involve cleaning with a
solvent, direct rinsing with water, or first
treating the part with an emulsifier and
then rinsing with water.

5. Developer Application: A thin layer of developer is then applied to the sample to

draw penetrant trapped in flaws back to the surface where it will be visible.
Developers come in a variety of forms that may be applied by dusting (dry
powders), dipping, or spraying (wet developers).

6. Indication Development: The developer

is allowed to stand on the part surface
for a period of time sufficient to permit
the extraction of the trapped penetrant
out of any surface flaws. This
development time is usually a minimum
of 10 minutes. Significantly longer
times may be necessary for tight cracks.

7. Inspection: Inspection is then performed under appropriate lighting to detect

indications from any flaws which may be present.

8. Clean Surface: The final step in the process is to thoroughly clean the part
surface to remove the developer from the parts that were found to be
acceptable.

Advantages and Disadvantages

The primary advantages and disadvantages when compared to other NDT methods
are:
Advantages
 High sensitivity (small discontinuities can be detected).

Introduction to Non-Destructive Testing Techniques Instructor: Dr. Ala Hijazi

Liquid Penetrant Testing Page 3 of 20

These materials have been adapted from https://www.nde-ed.org and are reused with permission.
  Few material limitations (metallic and nonmetallic, magnetic and nonmagnetic,
and conductive and nonconductive materials may be inspected).
 Rapid inspection of large areas and volumes.
 Suitable for parts with complex shapes.
 Indications are produced directly on the surface of the part and constitute a visual
representation of the flaw.
 Portable (materials are available in aerosol spray cans)
 Low cost (materials and associated equipment are relatively inexpensive)

Disadvantages
 Only surface breaking defects can be detected.
 Only materials with a relatively nonporous surface can be inspected.
 Pre-cleaning is critical since contaminants can mask defects.
 Metal smearing from machining, grinding, and grit or vapor blasting must be
removed.
 The inspector must have direct access to the surface being inspected.
 Surface finish and roughness can affect inspection sensitivity.
 Multiple process operations must be performed and controlled.
 Post cleaning of acceptable parts or materials is required.
 Chemical handling and proper disposal is required.

Penetrants
Penetrants are carefully formulated to produce the level of sensitivity desired by the
inspector. The penetrant must possess a number of important characteristics:
- spread easily over the surface of the material being inspected to provide
complete and even coverage.
- be drawn into surface breaking defects by capillary action.
- remain in the defect but remove easily from the surface of the part.
- remain fluid so it can be drawn back to the surface of the part through the
drying and developing steps.
- be highly visible or fluoresce brightly to produce easy to see indications.
- not be harmful to the material being tested or the inspector.

Introduction to Non-Destructive Testing Techniques Instructor: Dr. Ala Hijazi

Liquid Penetrant Testing Page 4 of 20

These materials have been adapted from https://www.nde-ed.org and are reused with permission.
Penetrant materials are not designed to perform the same. Penetrant manufactures
have developed different formulations to address a variety of inspection applications.
Some applications call for the detection of the smallest defects possible while in other
applications, the rejectable defect size may be larger. The penetrants that are used to
detect the smallest defects will also produce the largest amount of irrelevant
indications.
Standard specifications classify penetrant materials according to their physical
characteristics and their performance.
 Penetrant materials come in two basic types:
Type 1 - Fluorescent Penetrants: they contain a dye or several dyes that fluoresce
when exposed to ultraviolet radiation.
Type 2 - Visible Penetrants: they contain a red dye that provides high contrast
against the white developer background.
Fluorescent penetrant systems are more sensitive than visible penetrant systems
because the eye is drawn to the glow of the fluorescing indication. However,
visible penetrants do not require a darkened area and an ultraviolet light in order
to make an inspection.
 Penetrants are then classified by the method used to remove the excess penetrant
from the part. The four methods are:
Method A - Water Washable: penetrants can be removed from the part by rinsing
with water alone. These penetrants contain an emulsifying agent (detergent) that
makes it possible to wash the penetrant from the part surface with water alone.
Water washable penetrants are sometimes referred to as self-emulsifying
systems.
Method B - Post-Emulsifiable, Lipophilic: the penetrant is oil soluble and interacts
with the oil-based emulsifier to make removal possible.
Method C - Solvent Removable: they require the use of a solvent to remove the
penetrant from the part.
Method D - Post-Emulsifiable, Hydrophilic: they use an emulsifier that is a water
soluble detergent which lifts the excess penetrant from the surface of the part
with a water wash.

Introduction to Non-Destructive Testing Techniques Instructor: Dr. Ala Hijazi

Liquid Penetrant Testing Page 5 of 20

These materials have been adapted from https://www.nde-ed.org and are reused with permission.
 Penetrants are then classified based on the strength or detectability of the
indication that is produced for a number of very small and tight fatigue cracks. The
five sensitivity levels are:
Level ½ - Ultra Low Sensitivity
Level 1 - Low Sensitivity
Level 2 - Medium Sensitivity
Level 3 - High Sensitivity
Level 4 - Ultra-High Sensitivity
The procedure for classifying penetrants into one of the five sensitivity levels uses
specimens with small surface fatigue cracks. The brightness of the indication
produced is measured using a photometer.

Developers
The role of the developer is to pull the trapped penetrant material out of defects and
spread it out on the surface of the part so it can be seen by an inspector. Developers
used with visible penetrants create a white background so there is a greater degree of
contrast between the indication and the surrounding background. On the other hand,
developers used with fluorescent penetrants both reflect and refract the incident
ultraviolet light, allowing more of it to interact with the penetrant, causing more
efficient fluorescence.
According to standards, developers are classified based on the method that the
developer is applied (as a dry powder, or dissolved or suspended in a liquid carrier). The
six standard forms of developers are:
Form a - Dry Powder
Form b - Water Soluble
Form c - Water Suspendable
Form d - Nonaqueous Type 1: Fluorescent (Solvent Based)
Form e - Nonaqueous Type 2: Visible Dye (Solvent Based)
Form f - Special Applications
Introduction to Non-Destructive Testing Techniques Instructor: Dr. Ala Hijazi

Liquid Penetrant Testing Page 6 of 20

These materials have been adapted from https://www.nde-ed.org and are reused with permission.
Dry Powder
Dry powder developers are generally considered to be the least sensitive but they are
inexpensive to use and easy to apply. Dry developers are white, fluffy powders that can
be applied to a thoroughly dry surface in a number of ways; by dipping parts in a
container of developer, by using a puffer to dust parts with the developer, or placing
parts in a dust cabinet where the developer is blown around. Since the powder only
sticks to areas of indications since they are wet, powder developers are seldom used
for visible inspections.
Water Soluble
As the name implies, water soluble developers consist of a group of chemicals that are
dissolved in water and form a developer layer when the water is evaporated away. The
best method for applying water soluble developers is by spraying it on the part. The
part can be wet or dry. Dipping, pouring, or brushing the solution on to the surface is
sometimes used but these methods are less desirable. Drying is achieved by placing
the wet, but well drained part, in a recirculating warm air dryer with a temperature of
21°C. Properly developed parts will have an even, light white coating over the entire
surface.
Water Suspendable
Water suspendable developers consist of insoluble developer particles suspended in
water. Water suspendable developers require frequent stirring or agitation to keep the
particles from settling out of suspension. Water suspendable developers are applied to
parts in the same manner as water soluble developers then the parts are dried using
warm air.
Nonaqueous
Nonaqueous developers suspend the developer in a volatile solvent and are typically
applied with a spray gun. Nonaqueous developers are commonly distributed in aerosol
spray cans for portability. The solvent tends to pull penetrant from the indications by
solvent action. Since the solvent is highly volatile, forced drying is not required.
Special Applications
Plastic or lacquer developers are special developers that are primarily used when a
permanent record of the inspection is required.

Introduction to Non-Destructive Testing Techniques Instructor: Dr. Ala Hijazi

Liquid Penetrant Testing Page 7 of 20

These materials have been adapted from https://www.nde-ed.org and are reused with permission.
Preparation of Part
One of the most critical steps in the penetrant inspection process is preparing the part
for inspection. All coatings, such as paints, varnishes, plating, and heavy oxides must be
removed to ensure that defects are open to the surface of the part. If the parts have
been machined, sanded, or blasted prior to the penetrant inspection, it is possible that
a thin layer of metal may have smeared across the surface and closed off defects. Also,
some cleaning operations, such as steam cleaning, can cause metal smearing in softer
materials. This layer of metal smearing must be removed before inspection.

Penetrant Application and Dwell Time

The penetrant material can be applied in a number of different
ways, including spraying, brushing, or immersing the parts in a
penetrant bath. Once the part is covered with penetrant it must be
allowed to dwell so the penetrant has time to enter any defect
that is present.
There are basically two dwell mode options:
- Immersion-dwell: keeping the part immersed in the penetrant
during the dwell period.
- Drain-dwell: letting the part drain during the dwell period
(this method gives better sensitivity).
Penetrant Dwell Time
Penetrant dwell time is the total time that the penetrant is in contact with the part
surface. The dwell time is important because it allows the penetrant the time
necessary to seep or be drawn into a defect. Dwell times are usually recommended by
the penetrant producers or required by the specification being followed. The time
required to fill a flaw depends on a number of variables which include:
 The surface tension of the penetrant.
 The contact angle of the penetrant.
 The dynamic shear viscosity of the penetrant.
 The atmospheric pressure at the flaw opening.
 The capillary pressure at the flaw opening.
 The pressure of the gas trapped in the flaw by the penetrant.

Introduction to Non-Destructive Testing Techniques Instructor: Dr. Ala Hijazi

Liquid Penetrant Testing Page 8 of 20

These materials have been adapted from https://www.nde-ed.org and are reused with permission.
  The radius of the flaw or the distance between the flaw walls.
 The density or specific gravity of the penetrant.
 Microstructural properties of the penetrant.
The ideal dwell time is often determined by experimentation and is often very specific
to a particular application. For example, the table shows the dwell time requirements
for steel parts according to some of the commonly used specifications.

Penetrant Removal Process

The penetrant removal procedure must effectively remove the penetrant from the
surface of the part without removing an appreciable amount of entrapped penetrant
from the discontinuity. If the removal process extracts penetrant from the flaw, the
flaw indication will be reduced by a proportional amount. If the penetrant is not
effectively removed from the part surface, the contrast between the indication and the
background will be reduced.
Removal Method
As mentioned previously, penetrant systems are classified into four categories
according to the method used for excess penetrant removal.
- Method A: Water-Washable
- Method B: Post-Emulsifiable, Lipophilic
- Method C: Solvent Removable
- Method D: Post-Emulsifiable, Hydrophilic
Introduction to Non-Destructive Testing Techniques Instructor: Dr. Ala Hijazi

Liquid Penetrant Testing Page 9 of 20

These materials have been adapted from https://www.nde-ed.org and are reused with permission.
Method C, Solvent Removable, is used primarily for inspecting small localized areas.
This method requires hand wiping the surface with a cloth moistened with the solvent
remover, and is, therefore, too labor intensive for most production situations.
Method A, Water-Washable, is the most economical to apply of the different methods
and it is easy to use. Water-washable or self-emulsifiable penetrants contain an
emulsifier as an integral part of the formulation. The excess penetrant may be
removed from the object surface with a simple water rinse.
When removal of the penetrant from the defect due to over-washing of the part is a
concern, a post-emulsifiable penetrant system can be used. The post-emulsifiable
methods are generally only used when very high sensitivity is needed. Post-
emulsifiable penetrants require a separate emulsifier to breakdown the penetrant and
make it water washable. The part is usually immersed in the emulsifier but hydrophilic
emulsifiers may also be sprayed on the object. Brushing the emulsifier on to the part is
not recommended because the bristles of the brush may force emulsifier into
discontinuities, causing the entrapped penetrant to be removed. The emulsifier is
allowed sufficient time to react with the penetrant on the surface of the part but not
given time to make its way into defects to react with the trapped penetrant.
Controlling the reaction time is of essential importance when using a post-emulsifiable
system. If the emulsification time is too short, an excessive amount of penetrant will
be left on the surface, leading to high background levels. If the emulsification time is
too long, the emulsifier will react with the penetrant entrapped in discontinuities,
making it possible to deplete the amount needed to form an indication.
The hydrophilic post-emulsifiable method (Method D) is gives better sensitivity than
the lipophilic post-emulsifiable method (Method B). The major advantage of
hydrophilic emulsifiers is that they are less sensitive to variation in the contact and
removal time.
When a post-emulsifiable penetrant is used, the penetrant inspection process includes
the following steps (extra steps are underlined): 1. pre-clean part, 2. apply penetrant
and allow to dwell, 3. pre-rinse to remove first layer of penetrant, 4. apply hydrophilic
emulsifier and allow contact for specified time, 5. rinse to remove excess penetrant, 6.
dry part, 7. apply developer and allow part to develop, and 8. inspect.
Rinse Method and Time for Water-Washable Penetrants
The method used to rinse the excess penetrant from the object surface and the time of
the rinse should be controlled so as to prevent over-washing. It is generally
recommended that a coarse spray rinse or an air-agitated, immersion wash tank be
Introduction to Non-Destructive Testing Techniques Instructor: Dr. Ala Hijazi

Liquid Penetrant Testing Page 10 of 20

These materials have been adapted from https://www.nde-ed.org and are reused with permission.
used. When a spray is being used, it should be directed at a 45° angle to the part
surface so as to not force water directly into any discontinuities that may be present.
The spray or immersion time should be kept to a minimum through frequent
inspections of the remaining background level.
Hand Wiping of Solvent Removable Penetrants
When a solvent removable penetrant is used, care must also be taken to carefully
remove the penetrant from the part surface while removing as little as possible from
the flaw. The first step in this cleaning procedure is to dry wipe the surface of the part
in one direction using a white, lint-free, cotton rag. One dry pass in one direction is all
that should be used to remove as much penetrant as possible. Next, the surface should
be wiped with one pass in one direction with a rag moistened with cleaner. One dry
pass followed by one damp pass is all that is recommended. Additional wiping may
sometimes be necessary; but keep in mind that with every additional wipe, some of
the entrapped penetrant will be removed and inspection sensitivity will be reduced.

Use and Selection of a Developer

The use of developer is almost always recommended. The output from a fluorescent
penetrant is improved significantly when a suitable powder developer is used. Also, the
use of developer can have a dramatic effect on the probability of detection of an
inspection.
Nonaqueous developers are generally recognized as the most sensitive when properly
applied. However, if the thickness of the coating becomes too great, defects can be
masked. The relative sensitivities of developers and application techniques as ranked
in Volume II of the Nondestructive Testing Handbook are shown in the table below.
Ranking Developer Form Method of Application
1 Nonaqueous, Wet Solvent Spray
2 Plastic Film Spray
3 Water-Soluble Spray
4 Water-Suspendable Spray
5 Water-Soluble Immersion
6 Water-Suspendable Immersion
7 Dry Dust Cloud (Electrostatic)
8 Dry Fluidized Bed
9 Dry Dust Cloud (Air Agitation)
10 Dry Immersion (Dip)

Introduction to Non-Destructive Testing Techniques Instructor: Dr. Ala Hijazi

Liquid Penetrant Testing Page 11 of 20

These materials have been adapted from https://www.nde-ed.org and are reused with permission.
The following table lists the main advantages and disadvantages of the various
developer types.
Developer Advantages Disadvantages
Dry Indications tend to remain Does not form contrast
brighter and more distinct background so cannot be
over time used with visible systems

Easy to apply Difficult to assure entire part

surface has been coated
Soluble Ease of coating entire part Coating is translucent and
provides poor contrast (not
recommended for visable
systems)

Indications for water

washable systems are dim
and blurred
Suspendable Ease of coating entire part Indications weaken and
become diffused after time
Indications are bright and
sharp

White coating of good

contrast can be produced
which work well for both
visible and fluorescent
systems
Nonaqueous Very portable Difficult to apply evenly to
all surfaces
Easy to apply to readily
accessible surfaces More difficult to clean part
after inspection
White coating of good
contrast can be produced
which work well for both
visible and fluorescent
systems

Indications show-up rapidly

and are well defined

Provides highest sensitivity

Introduction to Non-Destructive Testing Techniques Instructor: Dr. Ala Hijazi

Liquid Penetrant Testing Page 12 of 20

These materials have been adapted from https://www.nde-ed.org and are reused with permission.
Quality & Process Control
Quality control of the penetrant inspection process is essential to get good and
consistent results. Since several steps and materials are involved in the inspection
process, there are quality control procedures for each of them.

Temperature Control
The temperature of the penetrant materials and the part being inspected can have an
effect on the results. Temperatures from 27 to 49°C are reported in the literature to
produce optimal results. Many specifications allow testing in the range of 4 to 52°C.
Raising the temperature beyond this level will significantly raise the speed of
evaporation of penetrants causing them to dry out quickly.
Since the surface tension of most materials decrease as the temperature increases,
raising the temperature of the penetrant will increase the wetting of the surface and
the capillary forces. Of course, the opposite is also true, so lowering the temperature
will have a negative effect on the flow characteristics.

Penetrant Quality Control

The quality of a penetrant inspection is highly dependent on the quality of the
penetrant materials used. Only products meeting the requirements of an industry
specification, such as AMS 2644, should be used. Deterioration of new penetrants
primarily results from aging and contamination. Virtually all organic dyes deteriorate
over time, resulting in a loss of color or fluorescent response, but deterioration can be
slowed with proper storage. When possible, keep the materials in a closed container
and protect from freezing and exposure to high heat.
Contamination can occur during storage and use. Of course, open tank systems are
much more susceptible to contamination than are spray systems. Regular checks must
be performed to ensure that the material performance has not degraded. When the
penetrant is first received from the manufacturer, a sample of the fresh solution
should be collected and stored as a standard for future comparison. The standard
specimen should be stored in a sealed, opaque glass or metal container. Penetrants
that are in-use should be compared regularly to the standard specimen to detect any
changes in properties or performance.

Introduction to Non-Destructive Testing Techniques Instructor: Dr. Ala Hijazi

Liquid Penetrant Testing Page 13 of 20

These materials have been adapted from https://www.nde-ed.org and are reused with permission.
Dwell Quality Control
Dwell times are usually recommended by the penetrant producer or required by the
specification being followed. The only real quality control required in the dwell step of
the process is to ensure that a minimum dwell time is reached. There is no harm in
allowing a penetrant to dwell longer than the minimum time as long as the penetrant
is not allowed to dry on the part.

Emulsifier Bath Quality Control

Quality control of the emulsifier bath is important and it should be performed per the
requirements of the applicable specification.
Lipophilic Emulsifiers
Lipophilic emulsifiers mix with penetrants but when the concentration of penetrant
contamination in the emulsifier becomes too great, the mixture will not function
effectively as a remover. Standards require that lipophilic emulsifiers be capable of
20% penetrant contamination without a reduction in performance. When the cleaning
action of the emulsifier becomes less than that of new material, it should be replaced.
Hydrophilic Emulsifiers
Hydrophilic emulsifiers have less tolerance for penetrant contamination. The penetrant
tolerance varies with emulsifier concentration and the type of contaminating
penetrant. In some cases, as little as 1% (by volume) penetrant contamination can
seriously affect the performance of an emulsifier.
Emulsifier Concentration and Contact Time
The optimal emulsifier contact time is dependent on a number of variables that include
the emulsifier used, the emulsifier concentration, the surface roughness of the part
being inspected, and other factors. Usually some experimentation is required to select
the proper emulsifier contact time.

Wash Quality Control

The wash temperature, pressure and time are three parameters that are typically
controlled in penetrant inspection process specification. A coarse spray or an
immersion wash tank with air agitation is often used. When the spray method is used,
the water pressure is usually limited to 276 kPa. The temperature range of the water is

Introduction to Non-Destructive Testing Techniques Instructor: Dr. Ala Hijazi

Liquid Penetrant Testing Page 14 of 20

These materials have been adapted from https://www.nde-ed.org and are reused with permission.
usually specified as a wide range (e.g., 10 to 38°C). The wash time should only be as
long as necessary to decrease the background to an acceptable level. Frequent visual
checks of the part should be made to determine when the part has been adequately
rinsed.

Drying Process Quality Control

The temperature used to dry parts after the application of an aqueous wet developer
or prior to the application of a dry powder or a nonaqueous wet developer, must be
controlled to prevent drying in the penetrant in the flaw. To prevent harming the
penetrant material, drying temperature should be kept to less than 71°C. Also, the
drying time should be limited to the minimum length necessary to thoroughly dry the
component being inspected.

Developer Quality Control

The function of the developer is very important in a penetrant inspection. In order to
accomplish its functions, a developer must adhere to the part surface and result in a
uniform, highly porous layer with many paths for the penetrant to be moved due to
capillary action. Developers are either applied wet or dry, but the desired end result is
always a uniform, highly porous, surface layer. Since the quality control requirements
for each of the developer types is slightly different, they will be covered individually.
Dry Powder Developer
A dry powder developer should be checked daily to ensure that it is fluffy and not
caked. It should be similar to fresh powdered sugar and not granulated like powdered
soap. It should also be relatively free from specks of fluorescent penetrant material
from previous inspection. This check is performed by spreading a sample of the
developer out and examining it under UV light.
When using the developer, a light coat is applied by immersing the test component or
dusting the surface. After the development time, excessive powder can be removed by
gently blowing on the surface with air not exceeding 35 kPa.
Wet Soluble/Suspendable Developer
Wet soluble developer must be completely dissolved in the water and wet
suspendable developer must be thoroughly mixed prior to application. The
concentration of powder in the carrier solution must be controlled in these developers.
Introduction to Non-Destructive Testing Techniques Instructor: Dr. Ala Hijazi

Liquid Penetrant Testing Page 15 of 20

These materials have been adapted from https://www.nde-ed.org and are reused with permission.
The concentration should be checked at least weekly using a hydrometer to make sure
it meets the manufacturer's specification. To check for contamination, the solution
should be examined weekly using both white light and UV light. Some specifications
require that a clean aluminum panel be dipped in the developer, dried, and examined
for indications of contamination by fluorescent penetrant materials.
These developers are applied by spraying, flowing or immersing the component. They
should never be applied with a brush. Care should be taken to avoid a heavy
accumulation of the developer solution in crevices and recesses.
Solvent Suspendable
Solvent suspendable developers are typically supplied in sealed aerosol spray cans.
Since the developer solution is in a sealed vessel, direct check of the solution is not
possible. However, the way that the developer is dispensed must be monitored. The
spray developer should produce a fine, even coating on the surface of the part. Make
sure the can is well shaken and apply a thin coating to a test article. If the spray
produces spatters or an uneven coating, the can should be discarded.
When applying a solvent suspendable developer, it is up to the inspector to control the
thickness of the coating. With a visible penetrant system, the developer coating must
be thick enough to provide a white contrasting background but not heavy enough to
mask indications. When using a fluorescent penetrant system, a very light coating
should be used. The developer should be applied under white light and should appear
evenly transparent.
Development Time
Parts should be allowed to develop for a minimum of 10 minutes and no more than 2
hours before inspecting.

Lighting Quality Control

Proper lighting is of great importance when visually inspecting a surface for a
penetrant indication. Obviously, the lighting requirements are different for an
inspection conducted using a visible dye penetrant than they are for an inspection
conducted using a fluorescent dye penetrant.
Lighting for Visible Dye Penetrant Inspections
When using a visible penetrant, the intensity of the white light is of principal
importance. Inspections can be conducted using natural lighting or artificial lighting.
Introduction to Non-Destructive Testing Techniques Instructor: Dr. Ala Hijazi

Liquid Penetrant Testing Page 16 of 20

These materials have been adapted from https://www.nde-ed.org and are reused with permission.
However, since natural daylight changes from time to time, the use of artificial lighting
is recommended to get better uniformity. Artificial lighting should be white whenever
possible (halogen lamps are most commonly used). The light intensity is required to be
100 foot-candles (1076 lux) at the surface being inspected.
Lighting for Fluorescent Penetrant Inspections
Fluorescent penetrant dyes are excited by UV light of 365nm wavelength and emit
visible light somewhere in the green-yellow range between 520 and 580nm. The
source of ultraviolet light is often a mercury arc lamp with a filter. The lamps emit
many wavelengths and a filter is used to remove all but the UV and a small amount of
visible light between 310 and 410nm. Visible light of wavelengths above 410nm
interferes with contrast, and UV emissions below 310nm include some hazardous
wavelengths.
Standards and procedures require verification of filter condition and light intensity. The
black light filter should be clean and the light should never be used with a cracked
filter. Most UV light must be warmed up prior to use and should be on for at least 15
minutes before beginning an inspection. Since fluorescence brightness is linear with
respect to ultraviolet excitation, a change in the intensity of the light (from age or
damage) and a change in the distance of the light source from the surface being
inspected will have a direct impact on the inspection. For UV lights used in component
evaluations, the normally accepted intensity is 1000 µW/cm2 at 38cm distance from
the filter face. The required check should be performed when a new bulb is installed,
at startup of the inspection cycle, if a change in intensity is noticed, or every eight
hours of continuous use.
When performing a fluorescent penetrant inspection, it is important to keep white
light to a minimum as it will significantly reduce the inspector’s ability to detect
fluorescent indications. Light levels of less than 2 foot-candles (22 lux) are required by
most procedures. When checking black light intensity a reading of the white light
produced by the black light may be required to verify white light is being removed by
the filter.
Light Measurement
Light intensity measurements are made using a radiometer (an instrument that
transfers light energy into an electrical current). Some radiometers have the ability to
measure both black and white light, while others require a separate sensor for each
measurement. Whichever type is used, the sensing area should be clean and free of
any materials that could reduce or obstruct light reaching the sensor. Radiometers are
Introduction to Non-Destructive Testing Techniques Instructor: Dr. Ala Hijazi

Liquid Penetrant Testing Page 17 of 20

These materials have been adapted from https://www.nde-ed.org and are reused with permission.
relatively unstable instruments and readings often change considerably over time.
Therefore, they should be calibrated at least every six months.

System Performance Check

A system performance check is typically required daily, at the reactivation of a system

after maintenance or repairs, or any time the system is suspected of being out of
control. System performance checks involve processing a test specimen with known
defects to determine if the process will reveal discontinuities of the size required. The
specimen must be processed following the same procedure used to process production
parts. The ideal specimen is a production item that has natural defects of the minimum
acceptable size. As with penetrant inspections in general, results are directly
dependent on the skill of the operator and, therefore, each operator should process a
test specimen.
There are some universal test specimens that can be used if
a reference part is not available. The most commonly used
test specimen is the TAM or PSM panel which is used for
fluorescent penetrant systems. These panels are usually
made of stainless steel that has been chrome plated on one
half and surfaced finished on the other half to produce the
desired roughness. The chrome plated section is impacted
from the back side to produce a starburst set of cracks in
the chrome. There are five impacted areas with a range of
different crack sizes corresponding to the five levels of sensitivity.
Care of system performance check specimens is critical.
Specimens should be handled carefully to avoid damage. They
should be cleaned thoroughly between uses and storage in a
solvent is generally recommended. Before processing a
specimen, it should be inspected under UV light to make sure
that it is clean and not already producing an indication.

Nature of the Defect

The nature of the defect can have a large effect on sensitivity of a liquid penetrant
inspection. Sensitivity is defined as the smallest defect that can be detected with a high
degree of reliability. Typically, the crack length at the sample surface is used to define
Introduction to Non-Destructive Testing Techniques Instructor: Dr. Ala Hijazi

Liquid Penetrant Testing Page 18 of 20

These materials have been adapted from https://www.nde-ed.org and are reused with permission.
size of the defect. However, the crack length alone does not determine whether a flaw
will be seen or go undetected. The volume of the defect is likely to be the more
important feature. The flaw must be of sufficient volume so that enough penetrant will
bleed back out to a size that is detectable by the eye or that will satisfy the
dimensional thresholds of fluorescence. The figure shows an example of fluorescent
penetrant inspection probability of detection (POD) curve as a function of crack length.

In general, penetrant testing is more effective at finding:

 Small round defects than small linear defects.
 Deeper flaws than shallow flaws.
 Flaws with a narrow opening at the surface than wide open flaws.
 Flaws on smooth surfaces than on rough surfaces.
 Flaws with rough fracture surfaces than smooth fracture surfaces.
 Flaws under tensile or no loading than flaws under compression loading.

Introduction to Non-Destructive Testing Techniques Instructor: Dr. Ala Hijazi

Liquid Penetrant Testing Page 19 of 20

These materials have been adapted from https://www.nde-ed.org and are reused with permission.
 Health and Safety Precautions
When proper health and safety precautions are followed, liquid penetrant inspection
operations can be completed without harm to inspection personnel. However, there is
a number of health and safety related issues that need to be taken in consideration.
The most common of those are discussed here.
Chemical Safety
Whenever chemicals must be handled, certain precautions must be taken. Before
working with a chemical of any kind, it is highly recommended that the material safety
data sheets (MSDS) be reviewed so that proper chemical safety and hygiene practices
can be followed. Some of the penetrant materials are flammable and, therefore,
should be used and stored in small quantities. They should only be used in a well
ventilated area and ignition sources avoided. Eye protection should always be worn to
prevent contact of the chemicals with the eyes. Gloves and other protective clothing
should be worn to limit contact with the chemicals.
Ultraviolet Light Safety
Ultraviolet (UV) light has wavelengths ranging from 180 to 400 nanometers. These
wavelengths place UV light in the invisible part of the electromagnetic spectrum
between visible light and X-rays. The most familiar source of UV radiation is the sun
and it is necessary in small doses for certain chemical processes to occur in the body.
However, too much exposure can be harmful to the skin and eyes. The greatest threat
with UV light exposure is that the individual is generally unaware that the damage is
occurring. There is usually no pain associated with the injury until several hours after
the exposure. Skin and eye damage occurs at wavelengths around 320 nm and shorter,
which is well below the 365 nm wavelength where penetrants are designed to
fluoresce. Therefore, UV lamps sold for use in penetrant testing are almost always
filtered to remove the harmful UV wavelengths. The lamps produce radiation at the
harmful wavelengths, so it is essential that they be used with the proper filter in place
and in good condition.

Introduction to Non-Destructive Testing Techniques Instructor: Dr. Ala Hijazi

Liquid Penetrant Testing Page 20 of 20

Best PDF Encryption Reviews
These materials have been adapted from https://www.nde-ed.org and are reused with permission.