0% found this document useful (0 votes)
23 views25 pages

Computer Network 22-23

Uploaded by

paraskadela02
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
23 views25 pages

Computer Network 22-23

Uploaded by

paraskadela02
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 25

Data Communication &

Computer Network

Lecture:22 & 23
Presented By
Dr. S.Kanungo
Error Control
• Mechanism for detection and correction of errors
• Types of Error
- Lost frames
- Damaged frames
• Common Techniques based on:
- Error detection
- Positive acknowledgment
- Retransmission after timeout
- Negative acknowledgement and retransmission
• These mechanisms are collectively referred as
Automatic Repeat Request (ARQ)
Automatic Repeat Request (ARQ)
• Stop and wait ARQ
• Go back N ARQ
• Selective reject (selective retransmission) ARQ

• Types of Error
- damaged frame
- damaged acknowledgement
Stop and Wait
• Source transmits single frame
• Simple and inefficient
• Wait for ACK
• If received frame damaged, discard it
– Transmitter has timeout
– If no ACK within timeout, retransmit
• If ACK damaged, transmitter will not recognize
it
– Transmitter will retransmit
– Receive gets two copies of frame
– Use ACK0 and ACK1
Stop and Wait – Diagram
Go Back N
• Based on sliding window
• If no error, ACK as usual with next frame
expected
• Use window to control number of
outstanding frames
• If error, reply with rejection
– Discard that frame and all future frames until
error frame received correctly
– Transmitter must go back and retransmit that
frame and all subsequent frames
Go Back N - Damaged Frame
• Receiver detects error in frame i
• Receiver sends rejection-i
• Transmitter gets rejection-i
• Transmitter retransmits frame i and all
subsequent
• Go Back N – Lost Frame (1)
- Frame i lost
- Transmitter sends i+1
- Receiver gets frame i+1 out of sequence
- Receiver send reject i
- Transmitter goes back to frame i and retransmits
• Go Back N - Lost Frame (2)
- Frame i lost and no additional frame sent
- Receiver gets nothing and returns neither
acknowledgement nor rejection
- Transmitter times out and sends acknowledgement frame
with P bit set to 1
- Receiver interprets this as command which it
acknowledges with the number of the next frame it expects
(frame i )
- Transmitter then retransmits frame i
• Go Back N - Damaged Acknowledgement
- Receiver gets frame i and send acknowledgement (i+1)
which is lost
- Acknowledgements are cumulative, so next
acknowledgement (i+n) may arrive before transmitter
times out on frame i
- If transmitter times out, it sends acknowledgement with
P bit set as before
- This can be repeated a number of times before a reset
procedure is initiated
• Go Back N - Damaged Rejection
- As for lost frame (2)
• Go Back N - Diagram
• Selective Reject
- Also called selective retransmission
- Only rejected frames are
retransmitted
- Subsequent frames are accepted by
the receiver and buffered
- Minimizes retransmission
- Receiver must maintain large enough buffer
- More complex login in transmitter
• High Level Data Link Control (HDLC)
- ISO 33009, ISO 4335
• HDLC Station Types
• Primary station
– Controls operation of link
– Frames issued are called commands
– Maintains separate logical link to each
secondary station
• Secondary station
– Under control of primary station
– Frames issued called responses
• Combined station
– May issue commands and responses
• HDLC Link Configurations
• Unbalanced
– One primary and one or more secondary stations
– Supports full duplex and half duplex
• Balanced
– Two combined stations
– Supports full duplex and half duplex
HDLC Transfer Modes
• Normal Response Mode (NRM)
- Unbalanced configuration
- Primary initiates transfer to secondary
- Secondary may only transmit data in response to
command from primary
- Used on multi-drop lines
- Host computer as primary
- Terminals as secondary
• Asynchronous Balanced Mode (ABM)
– Balanced configuration
– Either station may initiate transmission without
receiving permission
– Most widely used
– No polling overhead
• Asynchronous Response Mode (ARM)
– Unbalanced configuration
– Secondary may initiate transmission without
permission form primary
– Primary responsible for line
– rarely used
Frame Structure
• Synchronous transmission
• All transmissions in frames
• Single frame format for all data and control
exchanges
Frame Structure
Flag Fields
• Delimit frame at both ends
• 01111110
• May close one frame and open another
• Receiver hunts for flag sequence to synchronize
• Bit stuffing used to avoid confusion with data containing
01111110
– 0 inserted after every sequence of five 1s
– If receiver detects five 1s it checks next bit
– If 0, it is deleted
– If 1 and seventh bit is 0, accept as flag
– If sixth and seventh bits 1, sender is indicating abort
• Bit Stuffing
• Example with
possible errors
Address Field
• Identifies secondary station that sent or will receive frame
• Usually, 8 bits long
• May be extended to multiples of 7 bits
– LSB of each octet indicates that it is the last octet (1) or
not (0)
• All ones (11111111) is broadcast
Control Field
• Different for different frame type
– Information - data to be transmitted to user
(next layer up)
• Flow and error control piggybacked on information
frames
– Supervisory - ARQ when piggyback not used
– Unnumbered - supplementary link control
• First one or two bits of control filed identify
frame type
• Remaining bits explained later
• Control Field Diagram
Poll/Final Bit
• Use depends on context
• Command frame
– P bit
– 1 to solicit (poll) response from peer
• Response frame
– F bit
– 1 indicates response to soliciting command
• Information Field
- Only in information and some unnumbered frames
- Must contain integral number of octets
- Variable length
• Frame Check Sequence Field
- FCS
- Error detection
- 16 bit CRC
- Optional 32 bit CRC
• HDLC Operation
• Exchange of information, supervisory and unnumbered frames
• Three phases
– Initialization
– Data transfer
– Disconnect
• Examples of Operation (1)
• Examples of Operation (2)

You might also like