ELECTRICAL DESIGN DATA E24172

[ LOGO ] 250 / 250 kVA 10000 / 400 V Page 1 of 1

ROUND Core & Windings
Customer CANADA Spec CSA 3 Ph 60 Hz Dyn1 SC 500 MVA
Taps HV 5%, 2.5%, 0%, -2.5%, -5%
Insul Lvl LI 75 AC 28, LI 0 AC 10 Line Amps 14.43 / 360.84 A
Losses (W) @ 75°C Tap NLL Im% Wdg I²R Stray LoadL Imped % dBA
Calculated 3 572 0.31 2854 229 3084 3.87 50.99

Tested
Guarantee IEC 60076 3 566 3549 4.00 70.00
Transformer Efficiency : Unrestricted
COOLING ONAN : FLUID Mineral WGr LV,HV 11.7, 11.2 Max. 11.7 TOTAL W 3798
Guar Rises : Top Oil / Winding 60 / 65°C Temps : Hot Spot 118 °C Ambient 40 °C
Round Core D=181 / CL= 320 / WL= 235 B 1.635 Area 22083.84 V/T 9.623
Obround 0 Steel (27M4) Core & Coil Mass 577 kg
No. of Steps: 5 Mass 396 kg Stacked Height 164 mm
Step Size : 0 170 150 130 100 60 0 0 0 0 0 0
Thickness : 0.0 31.3 19.7 12.4 12.4 10.0 0.0 0.0 0.0 0.0 0.0 0.0
S/C Forces : End Clamp: 26.6 kN Bottom Yoke: 1.26 kN Edge Strip & End Supports: REQUIRED
WINDING DATA LV HV
Function Fraction Main 1.000 Main+Taps 1.000
Volts Turns 231 24 10500 1091
Riser | Tns/Lyr min 160mm² 1 Hole 99 2
Data | Layers CU 40 x 4 11 Pck 186mm 1
Layer Insul End 2 x ( 0.254 ) 2 x ( 0.254 )
Layer Insul Body 21 x ( 0.127 ) 9 x ( 0.254 )
Ducts Windw/Nose 2/2 of 3 2/2 of 3
Cond Xsec/Covrng 1// 200 x 0.5 1// 1.8 / 0.1
Bare/Cvd/Ord kg 13.9 / 13.9 / 41.8 21.6 / 22 / 66
Cond Mat/Cover CU SHEET CU WIRE / PVA2
Amps Area A/mm² 360.84 100 3.6084 8.3333 2.5447 3.2748
I²R Loss @ 75 °C 434 517
Radial W/Ns, NsLv 21.5 / 21.5, 31.1 32.5 / 32.5, 32.5
Clearance OD nom nom max
Wndw (core) 2.0 8 251 1.0 316 316
Nose ( ) 2.0 8 252 1.0 328 328

MTL 649 869

Axial Insulation 200 + 2 x 10 (Ends) = 220 190 + 2 x 15 (Ends) = 220
Rev. Description Complied By Approved By Date
O
A
 ELECTRICAL TEST DATA E24172
[ LOGO ] 250 / 250 kVA 10000 / 400 V Page 1 of 1
ROUND Core & Windings
Customer CANADA Spec CSA 3 Ph 60 Hz Dyn1 SC 500 MVA
Taps HV 5%, 2.5%, 0%, -2.5%, -5%
Insul Lvl LI 75 AC 28, LI 0 AC 10 Line Amps 14.43 / 360.84 A
Losses (W) @ 75°C Tap NLL Im% Wdg I²R Stray LoadL Imped % dBA
Calculated 3 572 0.31 2854 229 3084 3.87 50.99

Guarantee IEC 60076 3 566 3549 4.00 70.00

Transformer Efficiency : Unrestricted
COOLING ONAN : FLUID Mineral Max WGr 11.7 TOTAL W 3798
Guar Rises : Top Oil/Winding 60 / 65°C Temps : Hot Spot 118 °C Ambient 40 °C
Tap (1) HV PrTap 3 Tap (2) LV PrTap 1 Turns Ratio
Posn NomV Turns Amps Posn NomV Turns Amps 1/2
1 10500 1091 13.746 1 400 24 360.84 0 0 0 0 45.466 0
2 10250 1065 14.082 44.384 0
3 10000 1039 14.434 43.301 0
4 9750 1013 14.804 42.219 0
5 9500 987 15.193 41.136 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
WDG RES PH-PH /MAT @ 75°C HV (10000): 4.9676 / CU LV (400): 0.006665 / CU

Note :
REV O Original Issue
 Round Foil Winding (LV) Copper E24172
[ LOGO ] 250 kVA 400 V Page 1
Conductor 3 Coils/unit 1// 200 x 0.5 CU SHEET
Axial Length 200 + 2 x 10 (Ends) = 220 42 kg/unit
Edge Strips 10 mm x (2x(0.25)) Sticks 3 th. x 5 wide x H=217
Winding direction RIGHT
Leads CU 057-E24172 S1 40 x 4 (467, 349) Lead Position Out on LV nose
MANDREL 182 x 182, +1/-0
FORMER BOX NOT REQUIRED

Turns Instruction Remarks

0 0 LAYER WRAP Tape 1x(0.127) DDP (H=217) to Mandrel Nose

0 0 START LEAD (#2) 0.4 PB (80 x 435) - 2 under & 2 over
0 CU SHEET 20 mm from edge of Layer Wrap
0 8 STICK ALL ROUND
0 16 STICK ALL ROUND
0 24 FINISH LEAD (#1) 0.4 PB - under & over
0 24 CONTINUE LAYER WRAP Continue with single 0.127 DDP
0 26 STOP LAYER WRAP
0 27 STICK ALL ROUND Stick duct (3 th. x 5 wide x H=217)
0 28 1 x 0.8 PB CYLINDER Wrap All Round (H=220)
0 29 STICK ALL ROUND Stick duct (3 th. x 5 wide x H=217)
0 30 FINISH INSULATION
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
182
OD: 244 x 244 MAXIMUM

MANDREL : 182 41
(ONLY APPLICABLE FOR "OVAL" CORE)

185
Rev. Description Complied By Approved By Date
O
A
 [ LOGO ] Page 1
Conductor
Axial Length
Edge Strips Sticks
Winding direction
Leads Lead Position Out on LV nose
MANDREL
FORMER BOX

Turns Instruction Remarks

0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0

OD:

Rev. Description Complied By Approved By Date

O
A
 Round Wire Winding (HV) Copper E24172
[ LOGO ] 250 kVA 10000 V Page 2
Conductor 3 Coils/unit 1// 1.8 / 0.1 CU WIRE / PVA2
Axial Length 190 + 2 x 15 (Ends) = 220 66 kg/unit
Edge Strips 15 mm x (2x(0.8)+1x(0.25)) Sticks 3 th. x 5 wide x H=217
Winding direction RIGHT
Leads Single crepe paper tube Lead Position Out on HV nose
WDG (LV) Plus Insulation 244 x 244 MAXIMUM

Finish
Turns Instruction Insulation DD
Layer
0 0 0 Constant Insulation
Start 0 LEAD [S] - (START) 0.4 PB - 3 under & 2 over
0 1 99 0 2x(0.127)(F)
0 2 198 0 2x(0.127)(F)
0 3 297 0 2x(0.127)(F)
0 4 396 0 2x(0.127)(F)
0 0 STICK ALL ROUND 0
0 5 495 0 2x(0.127)(F)
0 6 594 0 2x(0.127)(F)
0 7 693 0 2x(0.127)(F)
0 8 792 0 2x(0.127)(F)
0 0 STICK ALL ROUND 0
0 9 891 0 2x(0.127)(F)
0 0 982 LEAD [5] 0
0 10 990 0 2x(0.127)(F)
0 0 1008 LEAD [3] 0
0 0 1034 LEAD [1,2] - (WINDING BREAK) 0
0 0 1060 LEAD [4] 0
0 0 1086 LEAD [6] 0
0 11 1089 0 2x(0.127)(F)
0 12 1091 LEAD [E] - (END) 0
Finish 0 0 0

OD : 309 x 312 MAXIMUM

NOTE: [-]

Rev. Description Complied By Approved By Date

O
A
 E24172
[ LOGO ] WINDING B.O.M.
Page 3
PARTS LIST FOR ONE UNIT CUTTING LIST FOR ONE UNIT
ITEM PART Nº QTY UOM %SC QTY DESCRIPTION
++++ ++++++++++ ++++ ++++ ++++ ++++ ++++++++++++++++++ WINDING LV ++++++++++++++++++
1 ? 42 kg 0 1 CU SHEET , 1// 200 x 0.5
2 ? 2.4 m 5 6 CU RISER 40 x 4 (467, 349)
3 ? 0.4 kg 5 3 CORE WRAP CYLINDER PB (0.8x599x220)
0 ?
4 ? 0.5 kg 5 27 RISER SCREEN PB (0.4x80x435)
5 ? 1.6 kg 5 1 0.127 DD 217 MM FOR 16 METER
0 ?
6 ? 0.6 kg 5 1 END INSULATION 0.25 DD x 10 FOR 31 METER
0 ?
7 ? 3.9 m 2 1 STICK DUCT CONTINUOUS 3x5x217
++++ ++++++++++ ++++ ++++ ++++ ++++ ++++++++++++++++++ WINDING HV ++++++++++++++++++
8 ? 66 kg 0 1 CU WIRE / PVA2, 1// 1.8 / 0.1
9 ? 2.2 kg 5 1 0.127 DD 217 MM FOR 21 METER
0 ?
10 ? 1.9 kg 5 1 END INSULATION 0.8 DD x 15 FOR 21 METER
11 ? 0.3 kg 5 1 END INSULATION 0.25 DD x 15 FOR 10 METER
12 ? 5.2 m 2 1 STICK DUCT CONTINUOUS 3x5x217
13 ? 2.2 m 10 1 SINGLE CREPE PAPER TUBE (LINE) 3x1.5x2000
14 ? 6.6 m 10 1 CREPE PAPER TUBE (TAPS) 5x1.5x2000
15 ? 0.3 kg 5 15 LEAD INSULATION 0.4 PB 80x435
16 ? 0.3 kg 5 2 PHASE BARRIER PB 2x305x215
++++ ++++++++++ ++++ ++++ ++++ ++++ +++++++++++++++++++ MAIN GAP +++++++++++++++++++
17 ? 0.2 kg 5 1 0.127 DD 217 MM FOR 2 METER
18 ? 13.3 m 2 1 STICK DUCT CONTINUOUS 3x5x217
19 ? 0.5 kg 5 3 CYLINDER PB 1// 0.8 x H=220
++++ ++++++++++ ++++ ++++ ++++ ++++ ++++++++++++++++++++++++++++++++++++++++++++++++
0 ?
0 ?
0 ?
0 ?
0 ?
0 ?
0 ?
0 ?
0 ?
0 ?
++++ ++++++++++ ++++ ++++ ++++ ++++ +++++++++++++++++++++++++++++++++++++++++++++++
0 ?
0 ?
0 ?
0 ?
0 ?
++++ ++++++++++ ++++ ++++ ++++ ++++ +++++++++++++++++++++++++++++++++++++++++++++++

Rev. Description Complied By Approved By Date

O
A