0% found this document useful (0 votes)
22 views3 pages

MENG 3500 LAB Requirements

Uploaded by

Hartej Tapia
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
22 views3 pages

MENG 3500 LAB Requirements

Uploaded by

Hartej Tapia
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

PROGRAMMABLE LOGIC CONTROLLERS

MENG 3500

LAB ASSIGNMENTS RUBRIC


PROGRAMMABLE LOGIC CONTROLLERS
MENG 3500

LABORATORY ASSIGNMENT SHEET


Lab Lab Successful Report
Description
Assignment Attendance Run Mark
1 Motor Control
Two-DC Motors Control With The
2
Problem Detection
3 Timers and Counters
4 Computations and Comparison
5 Cascading Sequence
6 Sequencer Output Application
7 Stepper Motor Control
8 Programming with ST, FBD, SFC
9 Temperature ON-OFF control
10 Temperature PID control

Student Name: Student No.

It is the student’s responsibility to keep this sheet up to date as the proof of the course
work.

Notes:
• The column titled Attendance will be checked at the end of the lab activity.
• The column titled Successful Runs, will be initialed when the assignment is seen to run
and satisfy the requirements.
• The column titled Report / Mark will be initialed when the report has been handed in to
the professor and marked.
• The minimum passing mark will be given to the signed assignments without written
report. All the labs have to be handed in with the screen captures related to the
programming/design steps.
PROGRAMMABLE LOGIC CONTROLLERS
LAB ASSIGNMENT – MARKING RUBRIC

Name Student No. Section

Lab Assig. No. Description Date

I. ASSIGNMENT EXECUTION / ASSIGNMENT RUNNING AT FULL FUNCTIONALITY


0.5 marks 1 mark 2 marks
- meets very little of the - meets some of the - meets or exceeds all of the
Functionality 0 marks
assignment criteria assignment criteria assignment criteria
/2
- limited functionality - some functionality - full functionality

II. LADDER DIAGRAM / PROGRAM REPORT


2 marks
- demonstrates acceptable
competence and
professionalism
0.5 marks 1 mark - all I/O & data points have
- demonstrates very - demonstrates some accurate symbols and/or
Ladder Program 0 marks
little competence and competence and descriptions /2
professionalism professionalism - rungs are documented
appropriately with concise
comments
- code/program is well
structured read

III. OBJECTIVE OF ASSIGNMENT / WHAT WENT WELL


2 marks
0.5 marks 1 mark
Response to III - succinctly describes what
- limited effectiveness at - somewhat effective
(your experience was accomplished in the lab
0 marks describing what was at describing what was
with the
accomplished in the lab accomplished in the
- a reader unfamiliar with the lab /2
assignment) would have a clear idea of
assignment lab assignment
what was accomplished

IV. CONCLUSION / WHAT COULD HAVE BEEN IMPROVED


2 marks
- demonstrates an exemplary
amount of critical thinking &
Response to IV 0.5 marks 1 mark
analysis
(suggestions/impr - demonstrates limited - demonstrates a fair
0 marks
critical thinking & amount of critical
- well communicated response /2
ovements about - a reader unfamiliar with the lab
the assignments) analysis thinking & analysis
would have a clear idea of
what was lacking and how it
could have been improved

V. DOCUMENTATION OF STEPS / PROCEDURES


0.5 marks 1 mark 2 marks
- demonstrates limited - demonstrates a fair - demonstrates an exemplary
Response to IV 0 marks
number of amount of steps/ amount of steps/procedures /2
steps/procedures procedures

Penalty (if applicable, e.g. illegible handwriting, incorrect/inaccurate information, late submission etc.) –

TOTAL / 10

You might also like