Chapter 5

Upgrading Memory
 Objectives

• Learn about the different kinds of physical memory

and how they work
• Learn how to upgrade memory
• Learn how to troubleshoot problems with memory

A+ Guide to Hardware modified by Dr. Feda AlShahwan 2

 Memory
Types of Memory
•There are three types of memory:
– Secondary Memory
– Main Memory
– Cache Memory
1.Secondary memory
– It is the slowest and cheapest form of memory. It
cannot be processed directly by the CPU. It must first
be copied into primary storage (Main memory).
– Secondary memory devices include magnetic disks
like hard drives and floppy disks, optical disks such as
CDs and CDROMs, and magnetic tapes, which were
the first forms of secondary memory. 3
A+ Guide to Hardware modified by Dr. Feda AlShahwan
 Memory
2. The Main Memory
– The main characteristic of this type of memory is that
it is much faster than secondary memory (i.e., Hard
disk and CD ROM). When you launch a program, it is
loaded into and run from the main memory. Data
used by the program also is loaded into memory for
fast access. As new data is entered into the
computer, it also is stored in memory. However it is
more expensive than secondary memory.
Types of Main Memory
• RAM and ROM
– RAM and ROM are the two basic types of storage
memory in the PC. RAM and ROM memory are used
to store data to which fast access is required.
A+ Guide to Hardware modified by Dr. Feda AlShahwan 4
 Memory
Due to its high cost, RAM and ROM memory is not used
to store large amounts of data permanently, such as
databases and word-processing documents.
– RAM is most commonly used as the temporary
storage area of CPU and other components of the
PC, such as video cards. The CPU uses this storage
space to hold both program instructions and
associated data. RAM is volatile, meaning that the
information it holds is dependent on a constant supply
of power. All data stored in it will be lost if the
computer is rebooted or turned off.
– ROM is typically used to store low-level hardware
instructions such as the motherboard and video-card
BIOS. ROM is non-volatile and does not require a
permanent power source to retain data.
A+ Guide to Hardware modified by Dr. Feda AlShahwan 5
 Memory
3. Cache Memory
– Cache memory is a type of volatile memory, which is
used for extremely fast access of information that has
already been previously accessed from the main
memory. It saves the CPU from having to go to the
main memory. This in turn saves time.
– There are two types of caches: L1 and L2 cache. The
L1 cache is housed inside the CPU to gain as much
data transfer speed as possible while the L2 cache
was placed outside, but nowadays both L1 and L2
caches are inside the CPU.
– Both caches operate at the speed of the CPU. So if
the CPU is 3.2GHz, then the speed of the L1 and L2
caches are also 3.2GHz. That means that the time it
takes to access a memory location is: 0.3ns. 6
A+ Guide to Hardware modified by Dr. Feda AlShahwan
 Memory Technologies
• Random access memory (RAM)
– Holds data and instructions used by CPU
• Types of RAM (Based on architecture)
• There are two main types of RAM, and every other
RAM is based on the design of these two types:
– Static RAM (SRAM) and dynamic RAM (DRAM)
• Both volatile memory

Figure 5-1 RAM on motherboards today is stored

on DIMMs
Courtesy: Course Technology/Cengage Learning

A+ Guide to Hardware modified by Dr. Feda AlShahwan 7

 RAM Types
• Static Random Access Memory (SRAM)
– Static RAM stores data in an electronic circuit called a
flip-flop. SRAM is approximately four or five times
faster than DRAM. Since every bit cell requires six or
more transistors to function under SRAM, compared
to one per bit for DRAM, SRAM modules are
relatively larger and more expensive than DRAM.
They are normally reserved for speed critical
functions, such as the system cache.

A+ Guide to Hardware modified by Dr. Feda AlShahwan 8

 RAM Types
• Dynamic Random Access Memory (DRAM)
– DRAM is used as the main or system memory of a
PC. It stores the operating system, application
programs and data while they are running.
It is created from transistors and capacitors. DRAM
stores data bits as electrical charges within the
structure of a single transistor. Each bit cell is very
small but the electrical charge gradually discharges,
causing the memory cell to lose its information. In
order to preserve the information, dynamic memory
has to be refreshed periodically by accessing each bit
cell at regular intervals. The refresh cycles slow down
the operation of DRAM but it is popular, mainly
because of its high-density (MB per chip) and low
price. 9
A+ Guide to Hardware modified by Dr. Feda AlShahwan
 DRAM Technologies
Types of DRAM
– Asynchronous DRAM
– Synchronous DRAM
Types of Asynchronous DRAM
1. FPM DRAM
– Fast Page Mode (FPM) DRAM offers faster accesses
than standard DRAM. While standard DRAM requires
that a row and column address be sent for each
access to a memory cell, FPM sends the row address
just once for many accesses to memory in locations
near each other. This improves access time.

A+ Guide to Hardware modified by Dr. Feda AlShahwan 10

 DRAM Technologies
2. EDO DRAM
– Extended Data Output (EDO) DRAM uses a modified
chip design that provides improvements in read times
of up to 30%. This performance gain is achieved by
continuing to output data from one address, while
simultaneously setting up the access request for the
next one.
3. BEDO DRAM
– Burst Extended Data Output (BEDO) DRAM is
supported by some motherboards, but has not gained
wide acceptance. It is similar in performance to
Synchronous DRAM.

A+ Guide to Hardware modified by Dr. Feda AlShahwan 11

 DRAM Technologies
Types of Synchronous DRAM
1. Synchronous DRAM
Synchronous DRAM (SDRAM) is designed to run at
the motherboard clock speed. SDRAM can run at
much higher clock speeds than other types of DRAM
and will be able to cope with faster motherboard
designs as they appear on the market.
SDRAM is available in three clock speeds: 66, 100,
and 133MHz. Motherboards are designed to support
specific types of RAM. You should always check which
types of memory can be fitted before supplying or
installing upgrades.

A+ Guide to Hardware modified by Dr. Feda AlShahwan 12

 DRAM Technologies
2. RDRAM (Rambus)
Rambus DRAM (RDRAM) has an effective clock
speed of up to 800MHz, compared to SDRAM's
133MHz. However, RDRAM has a bus width of 2 bytes
as opposed to SDRAM's bus width of 8 bytes. The
result is that RDRAM can achieve speeds of up to 1.6
GB/sec, while SDRAM can achieve speeds of up to
1.064 GB/sec. RDRAM is a proprietary memory type
and manufacturers who want to use it in their products
must pay a license fee to Intel and Rambus.

A+ Guide to Hardware modified by Dr. Feda AlShahwan 13

 DRAM Technologies
3. DDR SDRAM
Double Data Rate SDRAM (DDR SDRAM) is a variant
of SDRAM where data is transferred twice in one
cycle. It is available at speeds from 100 MHz to 166
MHz. The theoretical maximum bandwidth for 100
MHz DDR is 1.6 GB/sec (100 MHz x 2 x 8 bytes). DDR
is not as expensive as Rambus. SDRAM is referred to
by the clock speed (PC100, PC133, and so on). DDR
and the latest Rambus chips are labeled using the
maximum theoretical bandwidth (PC1600, PC2100,
and so on) - largely for marketing reasons.

A+ Guide to Hardware modified by Dr. Feda AlShahwan 14

 RAM Versions/ Memory Module
• RAM Versions (Module) (based on packaging)
– The packaging is simply the entire makeup of a unit of
memory, such as the SIMM or DIMM. Since the
memory chips themselves are way too small, they
must be combined and put onto a medium that can be
worked with and added to a system. So, designers
took the memory chips, placed them on a small
fiberglass card, and created the memory module.
– There are several different memory package styles
1. DIP (Dual In-Line Package) - This is the old classic
"chip" package of memory modules, the kind with
small pins undrneath that are plugged into pin
sockets. While this design led to the ability to remove
as required, it also led to the issue of broken memory
pins. 15
A+ Guide to Hardware modified by Dr. Feda AlShahwan
.

RAM Versions/Memory Module

2. SIP: Single In-line Package is memory package which
has one row of connecting pins.
3. SIMMs (Single Inline Memory Module): SIMMs comes
in two sizes, 30-pin and 72-pin. The 30 pin SIMMs
usually came with small amounts of memory (smaller
than 8MB). They are not used now, being mainly used
in earlier 486's and older machines. The 72-pin SIMMs
was much more popular, and was used on many
motherboards until SDRAM came into the picture.
Although you will occasionally see 72-pin SIMMS still in
use, it is usually only if you are opening up an old
system.

16
A+ Guide to Hardware modified by Dr. Feda AlShahwan
 RAM Versions/ Memory Module
• SIMMs come in both single sided and double sided
designs. This refers to whether the SIMM has memory
chips on one side of the SIMM or both. Usually, 1, 4, and
16MB SIMMs are single sided. Other sizes are double
sided. Some double sided SIMMs are actually two single
sided SIMMS back to back, where they are wired
together within the fiberglass module. These designs
operate a little different electrically, explaining why some
boards only use SIMMs of certain sizes.
4. DIMMs
• The DIMM is a newer designed memory module with a
64-bit memory pathway. SDRAM comes in DIMM format
with 168 pins, and DDR-DRAM comes in DIMM format
with 184 pins.
A+ Guide to Hardware modified by Dr. Feda AlShahwan 17
 RAM Versions/ Memory Module
• An architectural difference is the pin designs. With 72 pin
SIMMs, the electrical contacts (pins) are on both the
front and back, but are hooked together, so you only
have a total of 72 actual contacts. With DIMMs, the front
and back are kept separate, meaning you have 144 total
contacts. These contacts are more like little pads of
metal than pins. The edge connectors on each side of
card are electrically independent and this has the
following advantages:
• Doubles the available number of signal lines for a given
number of pins.
• Increase number of address and data bus lines width will
permit larger amount of memory.
A+ Guide to Hardware modified by Dr. Feda AlShahwan 18
 RAM Versions/ Memory Module
• The first DIMMs only had these 144-pins and were
sometimes called "Small Outline" (SO) DIMMs. The 168-
pin layout is the most common. There are additional pins
added to the DIMM, which keeps the DIMM from being
confused with the SIMM.
• They come with choices. They come in either 3.3 volt or
5 volt designs. They also come unbuffered or buffered.
This leads to 4 choices. The most common is the 3.3 volt
unbuffered, although you need to consult your
motherboard's documentation to determine the type you
really should have.

A+ Guide to Hardware modified by Dr. Feda AlShahwan 19

 DIMM Technologies
• DIMM (dual inline memory module)
– 64-bit data path
– Independent pins on opposite sides of module
– Older DIMMs
• Asynchronous with system bus
– Synchronous DRAM (SDRAM)
• Runs synchronously with system bus
• Two notches
• Uses 168 pins

A+ Guide to Hardware modified by Dr. Feda AlShahwan 20

 RAM Versions
5. RIMMs
• Quickly, the RIMM is the packaging style used for
Rambus RDRAM. It is very similar to a DIMM, but uses
different pin settings. The word RIMM is actually a
trademark of Rambus, and used to refer to a module
using Rambus technology.
6. SODIMM: Small Out DIMM - for Portable PCs

A+ Guide to Hardware modified by Dr. Feda AlShahwan 21

 Memory Technologies (cont’d.)

• Modules
– DIMM, small outline DIMM (SO-DIMM), microDIMMs
– RIMM and SIMM (outdated)
• Differences among DIMM, RIMM, SIMM modules
– Data path width each module accommodates
– How data moves from system bus to module

A+ Guide to Hardware modified by Dr. Feda AlShahwan 22

 Table 5-1 Types of memory modules
Courtesy: Course Technology/Cengage Learning

A+ Guide to Hardware modified by Dr. Feda AlShahwan 23

 Memory Technologies (cont’d.)
• JEDEC
– Standards organization
• Goal of new technology
– Increase overall throughput while retaining accuracy
– RAM manufacturers continue to produce older RAM

Figure 5-2 Timeline of memory technologies

Courtesy: Course Technology/Cengage Learning
A+ Guide to Hardware modified by Dr. Feda AlShahwan 24
 DIMM Technologies (cont’d.)
• Double Data Rate SDRAM
– Also called DDR SDRAM, SDRAM II, DDR
• Two times faster than SDRAM
– DDR2 SDRAM
• Faster than DDR and uses less power
– DDR3 SDRAM
• Faster than DDR2 and uses less power
– DDR2 and DDR3
• Use 240 pins
• Not compatible: use different notches
– Several factors affect capacity, features, and
performance
A+ Guide to Hardware modified by Dr. Feda AlShahwan 25
 DIMM Technologies (cont’d.)
• Single-sided DIMM
– Memory chips installed on one side of module
• Double-sided DIMM
– Memory chips installed on both sides of module
• Memory bank
– Memory processor addresses at one time
– 64 bits wide
• DIMMs can always be installed as single DIMMs on a
motherboard

A+ Guide to Hardware modified by Dr. Feda AlShahwan 26

 DIMM Technologies (cont’d.)
• Single ranked
– DIMMs providing only one 64-bit bank
• Dual and quad ranked
– DIMMs providing two and four banks
• Quad is used on servers
– Reduces overall memory price at the expense of
performance
• Single-ranked DIMMs
– Cost more than dual and quad
– Provide better performance

A+ Guide to Hardware modified by Dr. Feda AlShahwan 27

 DIMM Technologies (cont’d.)
• Early single channel DIMMs
– Memory controller is accessed one DIMM at a time
• Dual channels
– Memory controller communicates with two DIMMs at
the same time
• Doubles memory access speed
• Triple channels
– Accesses three DIMMs at once
• DDR, DDR2, DDR3 DIMMs use dual channels
– DDR3 DIMMs also use triple channels

A+ Guide to Hardware modified by Dr. Feda AlShahwan 28

 DIMM Technologies (cont’d.)
• Setting up dual channeling
– Pair of DIMMs in a channel must be equally matched
• Size, speed, features
• Use same manufacturer (recommendation)
• Setting up triple-channeling
– Three DIMM slots populated with three matching
DDR3 DIMMs

A+ Guide to Hardware modified by Dr. Feda AlShahwan 29

 Figure 5-3 Three identical DDR3 DIMMs installed in a triple-channel
configuration
Courtesy: Course Technology/Cengage Learning

A+ Guide to Hardware modified by Dr. Feda AlShahwan 30

 DIMM Technologies (cont’d.)

• DIMM Speed
– Measured in MHz or PC rating
• PC rating
– Total bandwidth between module and CPU
– DDR2 PC rating
• Usually labeled PC2
– DDR3 PC rating
• Usually labeled PC3

A+ Guide to Hardware modified by Dr. Feda AlShahwan 31

 DIMM Technologies (cont’d.)
• Error-correcting code (ECC)
– Detects and corrects error in a single bit
– Application: ECC makes 64-bit DIMM a 72-bit module
• Parity
– Error-checking based on an extra (ninth) bit
– Odd parity
• Parity bit set to make odd number of ones
– Even parity
• Parity bit set to make even number of ones
• Parity error
– Number of bits conflicts with parity used
A+ Guide to Hardware modified by Dr. Feda AlShahwan 32
 DIMM Technologies (cont’d.)

• Size and density of a DIMM

– DIMMs can hold 8 MB to 2 GB of RAM
– DIMM size or DIMM capacity
• Amount of RAM installed on one DIMM
– Sometimes expressed as a formula = total memory
size/number of slots

A+ Guide to Hardware modified by Dr. Feda AlShahwan 33

 DIMM Technologies (cont’d.)

• Buffered and registered DIMMs

– Hold data and amplify signal before data written
– Registered DIMM
• Uses registers
– Unbuffered DIMM
• No buffers or register support
– Fully buffered DIMM (FB-DIMM)
• Uses an advanced buffering technique
• Allows servers to support a large number of DIMMs
– Notches on module indicate supported technologies

A+ Guide to Hardware modified by Dr. Feda AlShahwan 34

 Figure 5-7 The positions of two notches on an SDRAM DIMM identify
the type of DIMM and the voltage requirement and also prevent the
wrong type from being installed on the motherboard
Courtesy: Course Technology/Cengage Learning

A+ Guide to Hardware modified by Dr. Feda AlShahwan 35

 DIMM Technologies (cont’d.)
• Measuring access timing
– Amount of time it takes the memory to respond to a
command. It only affects the initial burst of data. Once
data starts flowing, latency is no longer significant.
– Two measures:
• Column access strobe (CAS) latency
• Row access strobe (RAS) latency
– Both refer to number of clock cycles it takes to write or
read a column or row of data off a memory module
• CAS latency used more than RAS latency
• Lower values are better than higher
• Latency is measured in terms of clock cycles. A CL=2
chip requires two clock cycles to respond, and a CL=3
chip requires three clock cycles, therefore CL=2 chips
complete the initial data access a little more quickly
than CL=3 chips
36
A+ Guide to Hardware modified by Dr. Feda AlShahwan
 RIMM Technologies

• Direct Rambus DRAM

– Also known as RDRAM, Direct RDRAM, Rambus
– RIMM memory module
– Expensive and slower than current DIMMs
– RIMMs using 16-bit data bus: two notches, 184 pins
– RIMMs using 32-bit data bus: single notch, 232 pins
• C-RIMM (Continuity RIMM)
– Placeholder module
– Ensures continuity throughout all slots
– No memory chip
A+ Guide to Hardware modified by Dr. Feda AlShahwan 37
 Figure 5-8 A RIMM or C-RIMM must be installed in every
RIMM slot on the motherboard
Courtesy: Course Technology/Cengage Learning

A+ Guide to Hardware modified by Dr. Feda AlShahwan 38

 SIMM Technologies
• SIMMs rated by speed
– Measured in nanoseconds (ns)
– Measure of access time
• 60, 70, 80 nanoseconds (ns)
• Smaller number indicates greater speed
• Major SIMM categories
– 72-pin and 30-pin
• Technologies used by SIMMs
– FPM (fast page memory)
– EDO (extended data out)
– Burst EDO (BEDO)
A+ Guide to Hardware modified by Dr. Feda AlShahwan 39
 Memory Technologies and Memory
Performance
• Memory performance factors
– Memory Capacity: total RAM installed measured MB
or GB (comes in powers of 2, i.e., 128MB, 256MB,
512MB, 1GB)
– Memory technology used
• Memory module ( DIP / SIMM / DIMM /
SODIMM/SIP/RIMM)
• Memory type (DRAM/EDO DRAM/DDRAM)
– Speed of memory in MHz (frequency), PC rating
(bandwidth: calculated by multiplying the clock
frequency by the bus width), or ns (access time: it is
the time required for the memory device to locate and
output stored data measured in billionths of a second)

A+ Guide to Hardware modified by Dr. Feda AlShahwan 40

 Memory Technologies and Memory
Performance
• Memory performance factors (contd.)
– Maximum Memory Modules Capacity =
Total Memory Size/Number of memory slots
– ECC/parity or non-ECC/nonparity
– CL or RL rating
– Single, dual, or triple channeling
– Connectors color inside memory slots are tin or gold
• The color of memory slots should be the same color of
the connector to prevent corrosion. If you mix-match
them, over time a chemical reaction will take place
between the connectors. The product of that reaction
can cause unreliability and errors.

A+ Guide to Hardware modified by Dr. Feda AlShahwan 41

 How to Upgrade Memory
• Basic technique
– Add more RAM modules
• Why the memory needed to be up-graded?
• Up-grading the memory is results in better
performance
• It Allows multitasking: more tasks can be done
simultaneously
• Additional memory will not increase the speed of
the CPU, but it will reduce the time a CPU spends
waiting for information from the hard drive. RAM
provides data to a CPU faster than a hard drive, so
it will not take as long for programs to execute.
A+ Guide to Hardware modified by Dr. Feda AlShahwan 42
 How to Upgrade Memory
• Problems solved
– Slow performance
– Applications refusing to load
– An unstable system
– Windows “Insufficient memory” error message
– Bad memory module

A+ Guide to Hardware modified by Dr. Feda AlShahwan 43

 Precautions for Installing memory
When Installing memory modules follow these
precautions:
– Avoid mixing RAM from various suppliers and with
various specifications in the same PC – even if others
say it is fine to do so.
– Note that the RAM chips are produced at one factory,
and the RAM modules may be produced at another.
– Buy standard RAM from a supplier you trust. You
need to know who manufactured the RAM modules
and the seller needs to have sold them over a longer
period of time. Good brands are Samsung, Kingston
and Corsair
A+ Guide to Hardware modified by Dr. Feda AlShahwan 44
 Precautions for Installing memory
– The modules have to match the motherboard. Ensure
that they have been tested at the speed you need to
use them at.
– The best thing is to buy the motherboard and RAM
together. It’s just not always the cheapest.
– Avoid modules with more than 8 chips on each side.
– Memory added should be identical (Speed – Type ) to
memory that already is installed but it can be differ in
the capacity .
– The frequency of added memory should be matching
the CPU and Buses speed.

A+ Guide to Hardware modified by Dr. Feda AlShahwan 45

 Precautions for Installing memory
• Why the frequency of added memory should be
matching the CPU and Buses speed?
– If the memory is faster than CPU
→ The memory will be slow down
(waste of memory)
– If the memory is slower than The CPU / Bus speed
→ the memory will be heated or
burn up (cause damages)
• How to Read size of Memory installed?
– Boot- up
– BIOS
– Windows → System Information
– MEM command
46
A+ Guide to Hardware modified by Dr. Feda AlShahwan
 How to Upgrade Memory (cont’d.)

• Questions to ask
– How much RAM do I need and how much is currently
installed?
– How many and what kind of memory modules are
currently installed on my motherboard?
– How many and what kind of modules can I fit on my
motherboard?
– How do I select and purchase the right modules for
my upgrade?
– How do I physically install the new modules?

A+ Guide to Hardware modified by Dr. Feda AlShahwan 47

 How Much Memory Do I Need and
How Much Is Currently Installed?
• Best answer: “All you can get”
– Windows XP requires at least 512 MB RAM
– Windows Vista needs at least 2 GB
– RAM limit for a 32-bit OS
• 4 GB installed RAM

A+ Guide to Hardware modified by Dr. Feda AlShahwan 48

 How Many and What Kind of Memory
Modules Are Currently Installed?
• Open the case and look at memory slots
– How many slots?
– How many filled?
– Review module imprint
• Examine module for physical size and notch position
• Read motherboard documentation
– See if board supports dual channels or triple channels
• Last resort
– Take motherboard and old memory modules to a
good computer parts store for conformation
A+ Guide to Hardware modified by Dr. Feda AlShahwan 49
 Figure 5-10 Look for the manufacturer and model of a
motherboard imprinted somewhere on the board
Courtesy: Course Technology/Cengage Learning

A+ Guide to Hardware modified by Dr. Feda AlShahwan 50

 How Many and What Kind of Modules
Can Fit on My Motherboard?
• Taking out and replacing small-capacity modules
with larger-capacity modules:
– Use type, size, speed the board designed to support
• Discarding existing modules increases upgrade price
• Read motherboard documentation
– Indicates how much memory motherboard can
physically hold
– Select right number of DIMMs, RIMMs, SIMMs with
right amount of memory on each module to fit
memory banks on motherboard

A+ Guide to Hardware modified by Dr. Feda AlShahwan 51

 How Many and What Kind of Modules
Can Fit on My Motherboard? (cont’d.)
• DIMM modules
– DIMMs can be installed as single modules
• Performance may suffer
– Motherboard supporting dual channeling
• Install matching DIMMs in each channel for best
performance
– DDR3 board supporting triple channeling
• For best performance install three matching DIMMs in
triple-channel slots

A+ Guide to Hardware modified by Dr. Feda AlShahwan 52

 How Many and What Kind of Modules
Can Fit on My Motherboard? (cont’d.)
• Motherboard using DDR3 triple-channel DIMMs

Figure 5-11 Four DDR3 slots on a motherboard

Courtesy: Course Technology/Cengage Learning

A+ Guide to Hardware modified by Dr. Feda AlShahwan 53

 How Many and What Kind of Modules
Can Fit on My Motherboard? (cont’d.)
• Motherboard using DDR3 triple-channel DIMMs
(cont’d.)
– Use three matching DIMMs in the three blue slots
• If fourth slot populated, board reverts to single
channeling
– Dual channeling:
• Install two matching DIMMs in two blue slots farthest
from processor
• Leave other two slots empty
– For one installed DIMM:
• Place it in the blue slot farthest position from processor
A+ Guide to Hardware modified by Dr. Feda AlShahwan 54
 How Many and What Kind of Modules
Can Fit on My Motherboard? (cont’d.)
• Motherboard using DDR3 triple-channel DIMMs
(cont’d.)
– Follow motherboard documentation
– Serial Presence Detect (SPD)
• Declares module’s size, speed, voltage, and data path
width to system BIOS at startup
• Today’s memory always supports SPD

A+ Guide to Hardware modified by Dr. Feda AlShahwan 55

 How Many and What Kind of Modules
Can Fit on My Motherboard? (cont’d.)
• Motherboard using DDR DIMMs with dual
channeling

Figure 6-41 Carefully push the cooler assembly clips into the
retention mechanism on the motherboard until they snap into position
Courtesy: Course Technology/Cengage Learning
A+ Guide to Hardware modified by Dr. Feda AlShahwan 56
 How Many and What Kind of Modules
Can Fit on My Motherboard? (cont’d.)
• Motherboard using DDR DIMMs with dual
channeling (cont’d.)
– Example: ASUS P4P800 (cont’d.)
• Allows three different DDR DIMM speeds in one to four
sockets, supports dual channeling
• Two blue memory slots and two black slots
• For dual channeling
– Matching DIMMs must be installed in the two blue
sockets
• If two DIMMs installed in the two black sockets
– They must match each other

A+ Guide to Hardware modified by Dr. Feda AlShahwan 57

 How Many and What Kind of Modules
Can Fit on My Motherboard? (cont’d.)
• Motherboard using DDR DIMMs with dual
channeling (cont’d.)
– Example: ASUS P4P800 (cont’d.)

Figure 5-12 Motherboard documentation shows that one, two, or four

DIMMs can be installed
Courtesy: Course Technology/Cengage Learning

A+ Guide to Hardware modified by Dr. Feda AlShahwan 58

 How Many and What Kind of Modules
Can Fit on My Motherboard? (cont’d.)
• Pentium motherboard using DDR DIMMs
– Example: Motherboard using 168-pin single-sided
DIMM modules
– Documentation says to use unbuffered, 3.3-V, ECC,
PC100 DIMM SDRAM modules
• PC100: modules should be rated to work with a
motherboard running at 100 MHz
– Can choose to use or not use ECC modules
• BIOS setup should show feature disabled
– Three DIMM slots on the board (sockets) hold one
bank of memory

A+ Guide to Hardware modified by Dr. Feda AlShahwan 59

 How Many and What Kind of Modules
Can Fit on My Motherboard? (cont’d.)
• Pentium motherboard using DDR DIMMs (cont’d.)

Figure 5-14 This table is part of the motherboard documentation and is

used to show possible DIMM sizes and calculate total memory on the
motherboard
Courtesy: Course Technology/Cengage Learning

A+ Guide to Hardware modified by Dr. Feda AlShahwan 60

 How Many and What Kind of Modules
Can Fit on My Motherboard? (cont’d.)
• Motherboard using DDR DIMMs, single- or double-
sided
– Intel CC820 motherboard has two DIMM slots
• Combination of single-sided and double-sided DIMMs

Figure 5-15 The Intel CC820 motherboard can use a combination

of single-side and double-sided DIMMs
Courtesy: Course Technology/Cengage Learning
A+ Guide to Hardware modified by Dr. Feda AlShahwan 61
 How Many and What Kind of Modules
Can Fit on My Motherboard? (cont’d.)
• Motherboard with three slots using DDR DIMMs in
four banks
– Abit ZM6 board has three DIMM slots, chipset
supporting up to four 64-bit banks
• Using three slots to fill four banks
• Install combination of single-sided and double-sided,
dual-banked DIMMs

A+ Guide to Hardware modified by Dr. Feda AlShahwan 62

 Figure 5-16 How three DIMM slots can use four 64-bit
memory banks supported by a motherboard chipset
Courtesy: Course Technology/Cengage Learning

A+ Guide to Hardware modified by Dr. Feda AlShahwan 63

 How Many and What Kind of Modules
Can Fit on My Motherboard? (cont’d.)
• RIMM modules
– No longer made
– Replace one or more C-RIMMs with RIMMs
• Match new RIMMs existing RIMMs
• Follow motherboard documentation
– Example: Intel D850MV board with four RIMM slots
• First two slots populated with RIMMs (256 MB)
• Second two slots hold C-RIMMs
– Look at existing modules and motherboard
documentation

A+ Guide to Hardware modified by Dr. Feda AlShahwan 64

 Figure 5-17 Use the label on this RIMM to identify its features
Courtesy: Course Technology/Cengage Learning

Table 5-2 One motherboard’s memory configurations using RIMMs

A+ Guide to Hardware modified by Dr. Feda AlShahwan 65

 How Many and What Kind of Modules
Can Fit on My Motherboard? (cont’d.)
• SIMM modules
– To accommodate 64-bit system bus data path:
• 72-pin SIMMs have 32-bit data path installed in groups
or banks of two
– Older motherboards have one to three banks
• Can fill with two, four, or six SIMMs
• Two SIMMs in each bank must match in size and
speed
– Even older motherboards:
• 30-pin SIMMs installed in groups of four
• SIMMs in each bank must be same type and size
– See motherboard documentation
A+ Guide to Hardware modified by Dr. Feda AlShahwan 66
 How Do I Select and Purchase the
Right Memory Modules?
• Compromises if exact match not available
– Mixing unbuffered memory with buffered
• Registered memory will not work
– Match memory module manufacturer if possible
• Try using memory from two different manufacturers
– If mixing memory speeds:
• All modules perform at slowest speed
• For SIMMs, always put slower SIMMs in first bank

A+ Guide to Hardware modified by Dr. Feda AlShahwan 67

 How Do I Select and Purchase the
Right Memory Modules? (cont’d.)
• Buying high-quality memory
– Chip quality
• High-grade, low-grade, remanufactured, used
– Chip ID identifies chip manufacture date
• Stamped on each RAM module chip
– New chips have protective coating
• Gives a polished, reflective surface
– Re-marked chips
• Used, returned to the factory, marked again, resold

A+ Guide to Hardware modified by Dr. Feda AlShahwan 68

 How Do I Select and Purchase the
Right Memory Modules? (cont’d.)
• Using a web site to research your purchase
– Look for search utility matching modules to board

Figure 5-18 Web sites used to

purchase memory, such as this
Kingston site, often provide search
utilities to help you select the right
memory modules for your
motherboard
Courtesy: Course
Technology/Cengage Learning

A+ Guide to Hardware modified by Dr. Feda AlShahwan 69

 Figure 5-19 Selecting memory off the Crucial Web site
Courtesy: Course Technology/Cengage Learning

A+ Guide to Hardware modified by Dr. Feda AlShahwan 70

 How Do I Install the New Modules?

• Precautions:
– Always use a ground bracelet
– Turn off power, unplug power cord, press power
button, remove case cover
– Handle memory modules with care
– Do not touch metal contacts on memory module or
expansion cards
– Do not stack cards or modules

A+ Guide to Hardware modified by Dr. Feda AlShahwan 71

 How Do I Install the New Modules?
(cont’d.)
– Installing DIMMS
• Pull out supporting arms on the sides of the slot
• Use notches on DIMM edge connector as a guide
• Insert DIMM straight down into the slot
• Ensure supporting arms lock into position
• New installations are generally uncomplicated
– Usually involve placing memory on motherboard
– Older computers may need change to CMOS setup
– If new memory not recognized try reseating device

A+ Guide to Hardware modified by Dr. Feda AlShahwan 72

 Troubleshooting Memory Problems
Symptoms
• 1. Blue screen appears during installation or
running of Windows operating system
• 2. Crashes during memory intensive operations
such as 3D games, Photoshop, benchmark and
compiler
• 3. When power up the system it fails to boot and
beep codes emits indicating memory failure.
• 4. When restarting the system, memory count does
not match what has been installed and appeared in
BIOS.

A+ Guide to Hardware modified by Dr. Feda AlShahwan 73

 Troubleshooting Memory Problems
Causes
1. Configuration problem
2. Memory failure
Troubleshooting Procedures
1. Restart the system and enter the BIOS Setup.
Under a menu usually called Advanced or Chipset
Setup might be memory timing parameters. Select
BIOS or Setup defaults, which are usually the slowest
settings.
2. Save the settings, reboot, and. If the problem has
been solved, improper BIOS settings were the
problem. If the problem remains, you likely do have
defective memory, so continue to the next step.
A+ Guide to Hardware modified by Dr. Feda AlShahwan 74
 Troubleshooting Memory Problems
3. Check manual for proper memory specifications like
size, speed and type
4. Open the system for physical access to the memory
on the motherboard. Identify the bank arrangement in
the system and check if RAM is installed correctly and
check color of contacts.
5. Remove all the memory and clean memory slots
with compressed air and clean contacts with soft cloth.
6.Remove all except the first bank, and retest . If the
problem remains with all but the first bank removed,
the problem has been isolated to the first bank, which
must be replaced.

A+ Guide to Hardware modified by Dr. Feda AlShahwan 75

 Troubleshooting Memory Problems
7.Replace the memory in the first bank, preferably with
known good spare modules, but you can also swap in
others that you have removed and retest. If the
problem still remains after testing all the memory
banks (and finding them all to be working properly), it
is likely the motherboard itself is bad (probably one of
the memory sockets). Replace the motherboard and
retest.
8. At this point, the first (or previous) bank has tested
good, so the problem must be in the remaining
modules that have been temporarily removed. Install
the next bank of memory and retest. If the problem
resurfaces now, the memory in that bank is defective.
Continue testing each bank until you find the defective
76
module.
 Troubleshooting Memory Problems
9. Repeat the preceding step until all remaining banks
of memory are installed and have been tested. If the
problem has not resurfaced after removing and
reinstalling all the memory, the problem was likely
intermittent or caused by poor conduction on the
memory contacts. Often simply removing and
replacing memory can resolve problems because of
the self-cleaning action between the module and the
socket during removal and reinstallation.
10. If problem not solved then remove recently
installed Hardware or Software.

A+ Guide to Hardware modified by Dr. Feda AlShahwan 77

 Troubleshooting Memory Problems
Symptom
• Your computer starts to boot-up but then hangs, or
boots into the operating system and then upon
starting a large application, the system reboots itself
or hangs.
Causes
• There are several possible causes for this problem:
• Your power supply is inadequate for the load (number
of devices) connected to it, is overheating or the
voltage to the motherboard is inconsistent.
• The processor may be overheating.
• One or more chips in the upper memory areas of your
memory modules are bad or are going bad.

A+ Guide to Hardware modified by Dr. Feda AlShahwan 78

 Error code beeps for AMI

Beep Code Description

1 Short DRAMS refresh failure.
2 Short Parity circuit failure.
3 Short Base 64k RAM failure.
4 Short System timer failure.
5 Short Process failure.
6 Short Keyboard controller Gate A20 error.
7 Short Virtual mode exception error.
8 Short Display memory Read/Write test failure
9 Short ROM BIOS checksum failure.
10 Short CMOS shutdown Read/Write error.
11 Short Cache Memory error.
1 Long, 3 Short Conventional/Extended memory failure.
1 Long, 8 Short Display/Retrace test failed.

A+ Guide to Hardware modified by Dr. Feda AlShahwan 79

 Troubleshooting Memory Problems
Troubleshooting Procedure
• Verify that your power supply is adequate for the
number of attached devices. If it isn't, replace it with
one that is.
• Check your processor and make sure that it and the
attached heat sink and fan are clean and the fan is
working. Like the Power supply, we can have a new
fan to you over night.
• Lastly, swap your memory modules between slots,
e.g., swap module 0 with module 1 or 2 and then
start the system.

A+ Guide to Hardware modified by Dr. Feda AlShahwan 80