8-MAY-2024 56312E39
RYS8830
Small form factor & Ultra Low Power 1.8V UART/I2C interface GNSS antenna
module
Datasheet
11*11*2.2mm
RYS8830
Small form factor & Ultra Low Power 1.8V UART/I2C interface GNSS antenna module
PRODUCT DESCRIPTION
The REYAX RYS8830 1.8V GNSS module is built on the high performance of the SONY CXD5605AGF
GNSS engine. The RYS8830 module utilize concurrent reception of GNSS systems offering high
sensitivity in a small SMD form factor
FEATURES
• SONY CXD5605AGF Engine.
• A multi-GNSS module for GPS(L1 C/A), GLONASS(L1 OF), SBAS(L1 C/A), QZSS(L1 C/A), Galileo(E1
CBOC), and BeiDou(B1, specific Firmware).
• Small SMD form factor 121mm^2
• Including SAW filter, LNA and TCXO.
• Ultra-low power consumption
• Embedded Antenna.
• UART / I2C Interface optional.
2
Copyright © 2024, REYAX TECHNOLOGY CO., LTD.
RYS8830
Small form factor & Ultra Low Power 1.8V UART/I2C interface GNSS antenna module
BLOCK DIAGRAM
GNSS antenna RYS8830
Dotted line is
option
LNA
Filter
Flash
32.768KHz LNA
Oscillator
SONY
CXD5605AGF TCXO
Switching
multi-GNSS receiver
`Power
RXD TXD
SYSTEM0 SCL SDA PPS
Processor
3
Copyright © 2024, REYAX TECHNOLOGY CO., LTD.
RYS8830
Small form factor & Ultra Low Power 1.8V UART/I2C interface GNSS antenna module
PIN DESCRIPTION
G1 G4
GND GND
G2 G3
GND GND
1 22
GND GND
2 21
NC P02/UART0_CTS
3 20
LDO2_OUT P03/UART0_RTS
4 19
VDD P01/UART0_RXD/I2C0_SDA
5 18
LDO_IN P00/UART0_TXD/I2C0_SCL
P16/SEN_IRQ_IN
6 17
P06/BOOT_REC
LDO1_OUT P15/I2C1_SDA P04/1PPS_OUT
P14/I2C1_SCL
RTC_CLK_IN
7 16
P05/EXTLD
GND GND
SYSTEM0
RST_X
8
10
11
12
13
14
15
Pin Name I/O Condition
1,7,16,22,G1,G2,G3,G4 GND - Ground
2 NC - Leave Unconnected.
3 LDO2_OUT O LDO output for memory core blocks.
4 VDD I Power supply
5 LDO_IN I LDO0 / LDO1 Input
6 LDO1_OUT O LDO output for digital block.
8 I2C_SDA I/O I2C SDA *If not used, Please Leave Unconnected.
9 I2C_SCL I/O I2C SCL *If not used, Please Leave Unconnected.
10 BOOT_REC I/O Reserved, Connect to GND.
11 SEN_IRQ_IN I Interrupt input. *If not used, Please Leave
Unconnected.
12 RST_X I Low Reset
RTC 32.768KHz clock input,
13 RTC_CLK_IN I
The pin must be connected to GND, If not used.
14 SYSTEM0 I VDD : UART Interface, GND : I2C Interface.
EXTLD_IN I Timing signal input, from LTE module.
15
*If not used, Please Leave Unconnected.
17 P04/1PPS_OUT O Time pulse output, 1PPS output
18 TXD/SCL O Serial interface Output / I2C interface
19 RXD/SDA I/O Serial interface Input / I2C interface
20 UART_RTS I/O UART_RTS
21 UART_CTS I/O - UART_CTS
4
Copyright © 2024, REYAX TECHNOLOGY CO., LTD.
RYS8830
Small form factor & Ultra Low Power 1.8V UART/I2C interface GNSS antenna module
APPLICATION SCHEMATIC (VDD_LDO_IN = 0.92)
5
Copyright © 2024, REYAX TECHNOLOGY CO., LTD.
RYS8830
Small form factor & Ultra Low Power 1.8V UART/I2C interface GNSS antenna module
APPLICATION SCHEMATIC (VDD_LDO_IN = 1.8)
6
Copyright © 2024, REYAX TECHNOLOGY CO., LTD.
RYS8830
Small form factor & Ultra Low Power 1.8V UART/I2C interface GNSS antenna module
SPECIFICATION
Item Min. Typical Max. Unit Condition
Power Supply Voltage 1.71 1.8 1.89 V VDD
0.9 1.8 1.95 V VDD_LDO_IN
GNSS Normal mode
(1)
Idle Current 3.7 mA
(1)(3)
Satellite acquisition Current 16 19 mA
(1)(3)
Satellite tracking Current 9 13 mA
(2)(4)
Idle Current 3.3 mA
(2)(3)(4)
Satellite acquisition Current 11.5 mA
(2)(3)(4)
Satellite tracking Current 8.2 mA
(2)(4)
Sleep0 mode current 0.5 mA
(2)(4)
Sleep1 mode current 0.26 mA
(2)(4)
Sleep2 mode current 0.26 mA
GNSS low power mode
(2)(3)(4)
Satellite tracking average 2.6 8.2 mA
current @GSOP 2 1000 0
I2C slave I2C clock : 400kHz
Address length : 7 bits
Slave address : 0x24
Default Baud Rate 115200 bps 8,N,1
Digital input level high 0.7*VDD VDD+0.3 V VIH
Digital input level low -0.3 0.3*VDD V VIL
Digital output level high 0.8*VDD VDD V VOH 2mA
Digital output level low 0 0.2*VDD V VOL 2mA
Flash size 8 M-bit
1561.098 MHz BeiDou
GNSS Center Frequency 1575.42 GPS
1602.5625 GLONASS
Navigation update rate 1 Hz
Accuracy(2DRMS) 1 M Signal strength is -130dBm
(1) VDD_LDO_IN = 1.8V. (2) VDD_LDO_IN = 0.92V. (3) The typical value is field test. (4) Use buck regulator.
7
Copyright © 2024, REYAX TECHNOLOGY CO., LTD.
RYS8830
Small form factor & Ultra Low Power 1.8V UART/I2C interface GNSS antenna module
Cold starts 35 Sec. Signal strength is -130dBm
Hot starts 1 Sec.
Tracking Sensitivity -161 dBm
Hot starts Sensitivity -160 dBm
Cold starts Sensitivity -147 dBm
Velocity <0.1 m/s The measured value is based
on the condition of measured
with simulator, and receiver
moved at the constant speed
(20km/h)
Operating Temperature -40 25 +85 ˚C
Dimensions 11mm*11mm*2.2mm
Weight 0.43 g
8
Copyright © 2024, REYAX TECHNOLOGY CO., LTD.
RYS8830
Small form factor & Ultra Low Power 1.8V UART/I2C interface GNSS antenna module
3D Antenna Radiation Pattern
X
Y
9
Copyright © 2024, REYAX TECHNOLOGY CO., LTD.
RYS8830
Small form factor & Ultra Low Power 1.8V UART/I2C interface GNSS antenna module
10
Copyright © 2024, REYAX TECHNOLOGY CO., LTD.
RYS8830
Small form factor & Ultra Low Power 1.8V UART/I2C interface GNSS antenna module
REFLOW SOLDERING
Consider the "IPC-7530 Guidelines for temperature profiling for mass soldering (reflow and wave) processes, published 2001. Only
single reflow soldering processes are recommended for REYAX modules. Repeated reflow soldering processes and soldering the
module upside down are not recommended.
Preheat phase
Initial heating of component leads and balls. Residual humidity will be dried out. Please note that this preheat phase will not replace
prior baking procedures.
• Temperature rise rate: max. 3 °C/s If the temperature rise is too rapid in the preheat phase it may cause excessive slumping.
• Time: 60 - 120 s If the preheat is insufficient, rather large solder balls tend to be generated.
Conversely, if performed excessively, fine balls and large balls will be generated in clusters.
• End Temperature: 150 - 200 °C If the temperature is too low, non-melting tends to be caused in
areas containing large heat capacity.
Heating/ Reflow phase
The temperature rises above the liquidus temperature of 217°C. Avoid a sudden rise in temperature as the slump of the paste could
become worse.
• Limit time above 217 °C liquidus temperature: 40 - 60 s
• Peak reflow temperature: 245 °C
Cooling phase
A controlled cooling avoids negative metallurgical effects (solder becomes more brittle) of the solder and possible mechanical
tensions in the products. Controlled cooling helps to achieve bright solder fillets with a good shape and low contact angle.
• Temperature fall rate: max 4 °C/s To avoid falling off, the REYAX module should be placed on the topside of the motherboard
during soldering.
[°C] Y值
Preheat Heating Cooling
250 Peak Temp245°C
Liquidus temperature
217
200
40-60s Max 4°C/s
150
End Temp Typical Leadfree
Soldering Profile
Max 3°C/s 150-200°C
100 Y值
50
60-120s
0
0 50 100 150 200 250 300
座標軸標題
Elapsed Time
Recommended soldering profile
11
Copyright © 2024, REYAX TECHNOLOGY CO., LTD.
RYS8830
Small form factor & Ultra Low Power 1.8V UART/I2C interface GNSS antenna module
DIMENSIONS
Unit : mm
12
Copyright © 2024, REYAX TECHNOLOGY CO., LTD.
RYS8830
Small form factor & Ultra Low Power 1.8V UART/I2C interface GNSS antenna module
PCB FOOTPRINT
Unit : mm
13
Copyright © 2024, REYAX TECHNOLOGY CO., LTD.
RYS8830
Small form factor & Ultra Low Power 1.8V UART/I2C interface GNSS antenna module
PCB LAYOUT GUIDE
[1] Avoid placing any metal material between the RYS8830 and the sky.
[2] The best placement of the module is at the center of the PCB but close to the edge; keep at least
10 mm distance to the nearest ground plane corner.
[3] The height >2mm components should be placed at least 5 mm away from the RYS8830.
[4] The minimum distance between the plastic cover and the RYS8830 should be 1mm.
[5] The Placement of the module should keep a minimum distance of 5 mm from the human body
or the animal.
[6] The optimum PCB size is 78x 40 mm, but a larger or smaller ground plane can be used. The
suggested minimum ground plane size is 45 x 25mm.
[7] Place more GND via hole as close as possible to the RYS8830.
[8] Keep the VDD voltage ripple under 30mVpp.
[9] Avoid placing the module at the corner、center and short side of the PCB. This will reduce the
efficiency of the signal.
14
Copyright © 2024, REYAX TECHNOLOGY CO., LTD.
RYS8830
Small form factor & Ultra Low Power 1.8V UART/I2C interface GNSS antenna module
PCB TOP LAYER
BOTTOM LAYER
Unit : mm
15
Copyright © 2024, REYAX TECHNOLOGY CO., LTD.
RYS8830
Small form factor & Ultra Low Power 1.8V UART/I2C interface GNSS antenna module
GNSS Monitor software
STEP 1. INSTALL THE SOFTWARES
1.) Download the GNSS_Monitor2_ForCustomer_Setup(contact REYAX sales)
STEP 2. CONNECTION SETTING
Plug USB to TTL cable to connect the RYS8830_EVB and the PC.
1.) Open the software GNSS_Monitor2_ForCustomer Target →RYS8830 select CXD5605
2.) Open the Serial Port setting
3.) Set the COM port number and the baud rate (Default is 115200bps).
4.) If connection successful, will show FW version message.
16
Copyright © 2024, REYAX TECHNOLOGY CO., LTD.
RYS8830
Small form factor & Ultra Low Power 1.8V UART/I2C interface GNSS antenna module
STEP 3. Command input setting
1.) Click “IDLE” button, Terminal window will show [GSTP]Done.
2.) Click “Satellite Selection” button, after select Satellite and click “Send”. Terminal window will show
[GNS]Done.
3.) Click “Hot start” button, Terminal window will show [GSR]Done. Module start output NMEA log.
4.) If want to stop tracking, click “IDLE” button.
*For detailed command user guide, please refer to RYS8830_RYS8833_Software_Guide
QUICK START GUIDE
STEP 1. Power on module
STEP 2. Issue command
1.) @GSTP // Positioning stop
2.) @GNS 7 // Positioning-use satellite use GPS + GLONASS + SBAS
3.) @GTIM 2022 12 20 00 00 00 // inject UTC time
4.) @GPPS 1 // enable 1PPS function
5.) @GSR // hot start
*For detailed command user guide, please refer to RYS8830_RYS8833_Software_Guide
E-mail : [email protected]
Website : http://reyax.com
17
Copyright © 2024, REYAX TECHNOLOGY CO., LTD.
