MSF Flexible Couplings - Serration - Type

Electrical Insulation

■■ Structure
●● Set Screw Type
●● Recommended Applicable Motor
MSF
●● Ambient

Factor
Temperature / Temperature Correction

Servomotor ● Ambient Temperature Temperature Correction Factor

Casing Hex socket set screw
Stepping Motor ● -20℃ to 30℃ 1.00
General-purpose Motor ◎ 30℃ to 40℃ 0.80

◎: Excellent ○: Very good ●: Available 40℃ to 60℃ 0.70

●● Property

MSF
MSF W
Allowable Misalignment ○
B B
Vibration Absorption ○
F F M＊1 T
MSF Electrical Insulation ◎
Sleeve
Allowable Operating Temperature -20℃ to 60℃
●● Technical Information ◎: Excellent ○: Very good
●● Eccentric Reaction Force

D1

E
A

C
D2
●● The engagement of serration transmits torque. This
25
MSF-32 is a simple structure flexible coupling.
MSF-25
20 ●● Excellent flexibility. Its max. lateral misalignment
MSF-20
L L
MSF-16
and max. angular misalignment are large, absorbing
Load (N)

15 ＊1： In a case where the bore diameter is φ 4 or less, the set screw is used in only one place.
torsional vibration.
10

5
●● Application
■■ Dimensions Unit：mm

Mixer / Gaming device Screw Tightening Standard Bore Diameter (Dimensional Allowance H8)
Sleeve
Part Number ◀1 A B L W F M Torque D1/D2 ◀2
0 (N・m) T C E 3 4 5 6 6.35 8 10 12 14
●● Material/Finish
0 0.05 0.1 0.15 0.2 RoHS
Eccentricity (mm) MSF-16 16 12 8 27 4 M3 0.7 11 14 6 /   6 ● ● ● ● ● ●
MSF-16-MSF-25 MSF-32
ZDC2 SMF4040
MSF-20 20 15 10 34 5 M3 0.7 14 18 8 /   8 ● ● ● ● ●
●● Change in static torsional stiffness due to Casing
Cathodic Electrodeposition Coating Steam Treatment MSF-25 25 18 12 41 6 M4 1.7 17 22 10 / 10 ● ● ● ● ●
temperature
Sleeve Polyurethane Polyurethane MSF-32 32 21 14 48 7 M4 1.7 20 29 12 / 14 ● ● ● ●
This is a value under the condition where the static SCM435 SCM435
Hex Socket Set Screw
●● All products are provided with hex socket set screws.
torsional stiffness at 20℃ is 100%. Ferrosoferric Oxide Film (Black) Ferrosoferric Oxide Film (Black) ●● Recommended tolerance for shaft diameters is h6 and h7.

■■ Selection
Changes in the static torsion spring constant within ●● For the shaft insertion amount to the coupling, see Mounting/maintenance.

the operating temperature are shown in the graph.

If the unit is used under higher temperature, be ●● Selection Based on Shaft Diameter and Rated
■■ Performance
Max. Bore Max. Rotational Static Torsional Max. Lateral Max. Angular
careful about misalignment due to elongation or Torque Part Number Diameter
Rated Torque ＊1 Maximum Torque *1
Frequency
Moment of Inertia *2
Stiffness Misalignment Misalignment
Mass ＊2
(N・m) (N・m) (kg・m2) (g)
deflection of the shaft associated with thermal The area bounded by the shaft diameter and rated (mm) (min -1) (N・m/rad) (mm) (°
)

torque indicates the selection size. MSF-16 8 0.5 1 39000 9.0×10-7 4.4 0.2 2 22
expansion.
MSF-20 10 1 2 31000 2.7×10-6 9.5 0.2 2 42
110
MSF
10 MSF-25 12 1.5 3 25000 8.1×10-6 20 0.2 2 81
Static torsional stiffness (%)

MSF-32 15 3 6 19000 2.5×10-5 52 0.2 2 150

Rated torque (N・m)

100 ＊1： Correction of rated torque and max. torque due to load fluctuation is not required. However, if ambient temperature exceeds 30℃, be
MSF-32
sure to correct the rated torque and max. torque with temperature correction factor shown in the following table. The allowable
1.4
MSF-25 operating temperature of MSF is -20℃ to 60℃.
1
90 MSF-20 ＊2： These are values with max. bore diameter.
MSF-16

80
0 20 40 60 0.1
Temperature (°
C) 2 4 6 8 10 12 14 16
Shaft diameter (mm)
●● Part number specification
●● Selection Example
In case of selected parameters of shaft diameter of φ
MSF-16- 6-6.35 1 Set

◀1 ◀2
8 and load torque of 1.4 N•m, the selection size is
MSF-25 .
MSF-16- SLV Single Sleeve

Additional Keyway at Shaft Hole ➡ P.xxxx Cleanroom Wash & Packaging ➡ P.xxxx Change to Stainless Steel Screw ➡ P.xxxx ◀1 Single Sleeve
Available / Add'l charge Not Available Available / Add'l charge

▶ https://www.nbk1560.com ▶ https://www.nbk1560.com