website:http://biz.LGservice.

com
e-mail:http://www.LGEservice.com/techsup.html

PLASMA MONITOR
SERVICE MANUAL
CHASSIS : RF-052A

MODEL : 50PM1M/MA/MB
50PM1M/MA/MB-TA

CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
 CONTENTS

SAFETY PRECAUTIONS ....................................................................................3

DESCRIPTION OF CONTROLS ..........................................................................4

SPECIFICATIONS ................................................................................................9

ADJUSTMENT INSTRUCTIONS .......................................................................11

TROUBLE SHOOTING GUIDE ..........................................................................16

PRINTED CIRCUIT BOARD ..............................................................................25

BLOCK DIAGRAM .............................................................................................27

EXPLODED VIEW ..............................................................................................30

EXPLODED VIEW PARTS LIST ........................................................................31

REPLACEMENT PARTS LIST...........................................................................32

SCHEMATIC DIAGRAM.........................................................................................

- 2 -
 SAFETY PRECAUTIONS

IMPORTANT SAFETY NOTICE

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in
the Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to
prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.

General Guidance Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.
An isolation Transformer should always be used during Do not use a line Isolation Transformer during this check.
the servicing of a receiver whose chassis is not isolated from Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
the AC power line. Use a transformer of adequate power rating between a known good earth ground (Water Pipe, Conduit, etc.)
as this protects the technician from accidents resulting in and the exposed metallic parts.
personal injury from electrical shocks. Measure the AC voltage across the resistor using AC
voltmeter with 1000 ohms/volt or more sensitivity.
It will also protect the receiver and it's components from being Reverse plug the AC cord into the AC outlet and repeat AC
damaged by accidental shorts of the circuitry that may be voltage measurements for each exposed metallic part. Any
inadvertently introduced during the service operation. voltage measured must not exceed 0.75 volt RMS which is
corresponds to 0.5mA.
If any fuse (or Fusible Resistor) in this monitor is blown, replace In case any measurement is out of the limits specified, there is
it with the specified. possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
When replacing a high wattage resistor (Oxide Metal Film
Resistor, over 1W), keep the resistor 10mm away from PCB.

Keep wires away from high voltage or high temperature parts. Leakage Current Hot Check circuit

Due to high vacuum and large surface area of picture tube, AC Volt-meter
extreme care should be used in handling the Picture Tube.
Do not lift the Picture tube by it's Neck.

Good Earth Ground

such as WATER PIPE,
Leakage Current Cold Check(Antenna Cold Check) CONDUIT etc.
To Instrument’s 0.15uF
With the instrument AC plug removed from AC source, exposed
connect an electrical jumper across the two AC plug prongs. METALLIC PARTS
Place the AC switch in the on position, connect one lead of
ohm-meter to the AC plug prongs tied together and touch other
ohm-meter lead in turn to each exposed metallic parts such as 1.5 Kohm/10W
antenna terminals, phone jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1MΩ and 5.2MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.

- 3 -
 DESCRIPTION OF CONTROLS

MUTE POWER
MUTE POWER
switches the sound on or off. switches the set on from standby or
off to standby.
MULTIMEDIA INPUT MULTIMEDIA I/II
selects the Component, RGB or I/II (option)
HDMI modes. selects the language during dual lan-
LIST/ ARC MENU guage broadcast.
INPUT selects the sound output.

MENU
LIST (option) displays on screen menus one by one.
displays the programme table. exits the current menu.
memorizes menu changes.

OK
VOL VOL
D /E ARC
Selects a menu option. changes the picture format.
F / G (Volume Up/Down)
Increases/decreases sound level.
Adjusts menu settings.
OK
1 2 3
accepts your selection or displays the
NUMBER buttons
current mode.
4 5 6
SSM
7 8 9 to select the sound appropriate to
your viewing programme character.

PSM 0 SSM
PSM
TEXT/ (option)
adjusts the factory preset picture
according to the room. SPLIT ZOOM TEXT/ SLEEP
*
These buttons are used for teletext.
For further details, see the ‘Teletext’
section.
REVEAL MODE COLOURED BUTTONS :
SPLIT ZOOM These buttons are used for teletext.
enlarge the screen with regular ?
ration. SIZE MIX

Q.VIEW (option)
Returns to the previously viewed UPDATE Q.VIEW TIME SLEEP
programme. sets the sleep timer.
Note : This function works only when
Favourite prog. is set to Off. HOLD INDEX
Otherwise each press of this button i
will select a stored favorite
programme.

- 4 -
 <Front Panel Controls>

42PM1MA/J series / 50PM1MA/J series

5
3 2
ON/OFF
4

1. Main Power Button 6. D / E

Selects a menu option.
2. Remote Control Sensor F / G (Volume Up/Down)
Increases/decreases sound level.
3. Power Standby Indicator Adjusts menu settings.
Illuminates red in standby mode, Illuminates green when the
set is turned on

4. INPUT SELECT Button

5. MENU
Displays on screen menus one by one.
Exits the current menu.
Memorizes menu changes.

- 5 -
 <Back Panel>

AUDIO COMPONENT INPUT 2 MONITOR OUPUT

REMOTE RGB OUTPUT R L
CONTROL R L COMPONENT INPUT 1 A/V INPUT AC INPUT
Y PB PR R L R L (MONO) R L (MONO)
RS-232C INPUT HDMI/DVI
(CONTROL/SERVICE) (VIDEO) INPUT AUDIO INPUT RGB INPUT VARIABLE AUDIO OUT EXTERNAL SPEAKER
VIDEO AUDIO Antenna AUDIO VIDEO S-VIDEO AUDIO

Connection to PC Connection to AV equipment

- 6 -
 <Back Panel>

RCA Type

AUDIO COMPONENT INPUT 2 MONITOR OUPUT

REMOTE RGB OUTPUT R L
CONTROL R L COMPONENT INPUT 1 A/V INPUT AC INPUT
Y PB PR R L R L (MONO) R L (MONO)
RS-232C INPUT HDMI/DVI
(CONTROL/SERVICE) (VIDEO) INPUT AUDIO INPUT RGB INPUT VARIABLE AUDIO OUT EXTERNAL SPEAKER
VIDEO AUDIO Antenna AUDIO VIDEO S-VIDEO AUDIO

1 2 3 4 5

Scart Type

VIDEO AUDIO
AUDIO
REMOTE RGB OUTPUT R L Y PB PR L R
CONTROL R L COMPONENT INPUT AC INPUT
(MONO) AV3 AV1 AV2
RS-232C INPUT HDMI/DVI
(CONTROL/SERVICE) (VIDEO) INPUT AUDIO INPUT RGB INPUT VARIABLE AUDIO OUT EXTERNAL SPEAKER
S-VIDEO VIDEO Antenna

AV1

1. RS-232C INPUT(CONTROL/SERVICE) PORT 4. COMPONENT / AUDIO INPUT SOCKETS

Connect to the RS-232C port on a PC. S-VIDEO / AUDIO (L/MONO) INPUT SOCKETS
VIDEO / AUDIO (L/MONO) INPUT SOCKETS
2. HDMI/DVI (VIDEO) / AUDIO INPUT / RGB INPUT SOCKETS
Connect the monitor output socket of the PERSONAL COM- ANTENNA INPUT
PUTER to this socket.
Note: If you want to use RGB/DVI audio, we strongly recom- EURO SCART SOCKET
mend that you use the cable that has a core, or the EMI Filter Connect the euro scart socket of the VCR to these sockets.
core along with separate cable. Note:
a. If you want to use the EURO scart cable, you have to use
RGB OUTPUT SOCKET the signal shielded Euro scart cable.
You can watch the RGB signal on another set, connect RGB b. If you want to use your external hi-fi stereo system, turn off
OUTPUT to another monitor’s PC input port. the internal speakers of the set.
REMOTE CONTROL 5. POWER CORD SOCKET
This set operates on an AC power. The voltage is indicated on
VARIABLE AUDIO OUTPUT the Specifications page. Never attempt to operate the set on
DC power.
3. EXTERNAL SPEAKER OUTPUT (8 ohm)
Connect to optional external speaker(s).
* For further information, refer to ‘Speaker & Speaker Stand’
manual.

- 7 -
Accessories
MUTE POWER

INPUT MULTIMEDIA I/II

LIST/ ARC MENU

OK
VOL VOL

1 2 3

4 5 6

7 8 9

PSM 0 SSM

SPLIT ZOOM TEXT/ SLEEP

REVEAL MODE
?
SIZE MIX

LG TV UPDATE Q.VIEW TIME

HOLD INDEX
i
AS mark

Owner’s Manual Remote Control handset

1.5V
1.5V

Alkaline batteries
Power Cord

Optional Extras

- Optional extras can be changed or modified for quality improvement without any notification new optional extras can be
added.
- Contract your dealer for buying these items.

42
40
40
42
50

50 42 40 40 42 50

Tilt wall mounting bracket Desktop stand Ceiling mounting bracket

Speakers Video cables Audio cables

- 8 -
 SPECIFICATIONS
NOTE : Specifications and others are subject to change without notice for improvement.
V Application Range
This spec is applied to the PDP TV used RF-052A Chassis.

V Specification
Each part is tested as below without special appointment.
1) Temperature : 25±5°C (77±9°F), CST : 40±5
2) Relative Humidity: 65±10%
3) Power Voltage: Standard Input voltage (100-240V~, 50/60Hz)
* Standard Voltage of each product is marked by models.
4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM.
5) The receiver must be operated for about 20 minutes prior to the adjustment.

V Test Method
1) Performance : LGE TV test method followed.
2) Demanded other specification
Safety: IEC60065
EMI : CISPR13

V General Specification
1. Module Specification

No Item Specification Remark

1 Display Screen Device 50 inch wide Color Display Module PDP
2 Aspect Ratio 16:9
3 PDP Module PDP50X3,
RGB Closed Type
4 Operating Environment 1) Temp : 0~40 deg LGE SPEC
2) Humidity : 0~85%
5 Storage Environment 1) Temp : -20~60 deg
2) Humidity : 0~85%
6 Input Voltage 100-240V~, 50/60Hz Maker : SONY/ LGIT/ Sanken

- 9 -
2. Model Specification

No Item Specification Remark

1 Market Non-EU
2 Broadcasting system PAL B/G/I/D/K, NTSC
3 Available Channel BAND PAL
VHF E2~E12
UHF E21~E69
CATV S1~S47
HYPER S1~S20
4 Receiving system Upper Heterodyne
5 Video Input (1EA) PAL, SECAM, NTSC Except 42PM1MB, 50PM1MB, 42PM3MVB
6 Video Output(1EA) PAL, SECAM, NTSC Except 42PM1MB, 50PM1MB, 42PM3MVB
7 S-Video Input(1EA) PAL, SECAM, NTSC Except 42PM1MB, 50PM1MB, 42PM3MVB
8 Component Input(2EA) Y/Cb/Cr, Y/Pb/Pr
9 RGB Input RGB-PC, RGB-DTV
10 RGB Output RGB-PC, RGB-DTV
11 HDMI Input(1EA) HDMI-PC, HDMI-DTV
12 Audio Input(5EA) PC Audio, Component(2EA), 42PM1M, 42PM1MA, 50PM1M, 50PM1MA
AV(1EA), S-audio(1EA) 42PM3MV, 42PM3MVA
Audio Input(1EA) PC Audio 42PM1MB, 50PM1MB, 42PM3MVB
13 Audio Output(3EA) AV(1EA), External audio out(1EA), 42PM1M, 42PM1MA, 50PM1M, 50PM1MA,
Variable Audio out(1EA) 42PM3MV, 42PM3MVA
Audio Output(2EA) External audio out(1EA) 42PM1MB, 50PM1MB, 42PM3MVB
Variable Audio out(1EA)
14 Wired Control Discrete IR

- 10 -
 ADJUSTMENT INSTRUCTIONS
1. Application Object 3-2. Channel memory Method
These instructions is applied all of the PDP TV, RF-052A 1) Select “PDP” and “Hurricane” on Model dialog. And check
Chassis. your connection in Communication dialog. (If your
connection is ‘NG’, then set your PORT(COM1,2,3,...)
correctly.)
2. Specification 2) Connect RS-232C cable and turn on the power.
(1) Because this is not a hot chassis, it is not necessary to use (If your connection has completed, you can see “Ready”.)
an isolation transformer. However, the use of isolation
transformer will help protect test instrument. [ If your set is not an end products but only a board, you
(2) Adjustment must be done in the correct order. have to make your board to Stand-by state (LED_R). And
(3) The adjustment must be performed in the circumstance of you have to Download in Stand_by power state.
25±5°C of temperature and 65±10% of relative humidity if
there is no specific designation.
(4) The input voltage of the receiver must keep 100-220V,
50/60Hz.
(5) The receiver must be operated for about 15 minutes prior
to the adjustment.

O After RGB Full white HEAT-RUN Mode, the receiver must

be operated prior to adjustment.
O Enter into HEAT-RUN MODE
1) Press the POWER ON KEY on R/C for adjustment.
2) OSD display and screen display 100% full White pattern.

[ Set is activated HEAT-RUN without signal generator in (Fig. 2-1)

this mode.
[ Single color pattern(RED/BLUE/GREEN) of HEAT-RUN
mode uses to check PANEL. 3) Select proper CH_memory file(*.nvm) for each model at
[NVRAM Download] $ [Write Batch]
Caution) If you turn on a still screen more than 20 minutes, Next, select proper binary file(*.bin) including the CH
(Especially digital pattern, cross hatch pattern) after information for each model at [NVRAM File].
image may be occur in the black level part of the screen. 4) Click the [Download] button.
It means the completion of the CH memory download if all
items show ‘OK’ and Status is changed by ‘PASS’ at the
3. Channel memory lower right corner of the window.
5) If you want to check whether the CH information is
3-1. Setting up the LGIDS memorized correctly or not, click the [Verify] button.
1) Install the LGIDS. (idsinst.exe) And then compare NVRAM File(*.bin) with the CH
2) After installation, restart your PC. information downloaded.
3) Extract [files.zip] to folder [c:\LGIDS\files].
4) Start LGIDS.

(Fig. 2-2)

(Fig. 1)

- 11 -
 Each PCB assembly must be checked by check JIG set. 5-2. Setting of device
(Because power PCB Assembly damages to PDP Module,
especially be careful)

4. POWER PCB Assy Voltage

Adjustments (Va, Vs Voltage Adjustments)
4-1. Test Equipment : D.M.M. 1EA (Fig. 4) Connection Diagram of DDC download
4-2.Connection Diagram for Measuring
: refer to fig.3 5-3. Preparation for Adjustment
1) As above Fig. 5, Connect the Set, EDID Download Jig, PC
4-3. Adjustment Method & Cable.
[P/No 3501V00221A B/D] 2) Turn on the PC & EDID Download Jig. And Execute the
S/W : EDID TESTER Ver,2.5
(1) Va Adjustment 3) Set up S/W option
1) After receiving 100% Full White Pattern, HEAT RUN. Repeat Number : 5
2) Connect + terminal of D.M.M to Va pin of P805, connect Device Address : A0
- terminal to GND pin of P805. PageByte : 8
3) After turning RV601, voltage of D.M.M adjustment as 4) Power on the Set
same as Va voltage which on label of panel right/top.
(Deviation; ±0.5V)

(2) Vs Adjustment
1) Connect + terminal of D.M.M to Vs pin of P805, connect
– terminal to GND pin of P805.
2) After turning RV401, voltage of D.M.M adjustment as
same as Va voltage which on label of panel right/top.
(Deviation; ±0.5V)

Va

GND
P806
5-4. Sequence of Adjustment
NC
VS P805

DMM Va ADJ
Vs ADJ
RV401 (1) DDC data of Analog-RGB
+ - P804
RV601
1) Init the data

P807

P801 P802 P803

(Fig. 3) Connection diagram of power adjustment for measuring

2) Load the EDID data.(Open File)
[Analog-RGB : MF056A_RGB.ANA]
[digital(HDMI) : MF056A_DMI.DVI]
5. EDID (The Extended Display 3) Set the S/W as below.
Identification Data)/ DDC (Display 4) Push the “Write Data & Verify”button. And confirm “Yes”.
5) If the writing is finished, you will see the “OK” message.
Data Channel) download
5-1. Required Test Equipment
1) Adjusting PC with S/W for writing EDID Data.(S/W : EDID
TESTER Ver.2.5)
2) A Jig for EDID Download
3) Cable : Serial(9Pin or USB) to D-sub 15Pin cable, D-sub
15Pin cable, DVI to HDMI cable

- 12 -
 7. Adjustment of White Balance
7-1. Required Equipment
1) Remote controller for adjustment
2) Color Analyzer (CA-100 or same product)
3) Auto W/B adjustment instrument(only for Auto adjustment)
4) AV Pattern Generator

7-2. Connecting diagram of equipment for

measuring (For Auto Adjustment)
COLOR
ANALYZER
216 Level (85 IRE) TYPE ; CA-100

CVBS
signal
input
M SPG-2 1 0 0 /
M STG- 5 2 0 0
(Fig.5) EDID DATA

6. Auto AV(CVBS) Color Balance RS-232C Serial Communication

(Fig. 7) Connection Diagram of Auto W/B Adjustment

6-1. Requirement
- This AV color balance adjustment should be performed
W Auto adjustment Map(RS-232C)
before white Balance Adjustment
Type RF-052A/B/C
6-2. Required Equipment
1) Remote controller for adjustment Baud Rate Data bit Stop bit Parity
2) AV Pattern Generator 115200 8 1 NONE
: 802F Pattern Generator, Master(MSPG-925FA), etc
(Which has PAL Composite Video format output with Index Cmd1 Cmd2 Data Min Value Max Value
standard(1.0 Vpp) Vertical 100% Color Bar Pattern as Fig6) R Gain j a 00(00) 255(FF)

216 Level (85 IRE) G Gain j b 00(00) 255(FF)

Protocol
B Gain j c 00(00) 255(FF)
Setting
R Offset j d 00(00) 255(FF)
G Offset j e 00(00) 255(FF)
B Offset j f 00(00) 255(FF)

7-3. Adjustment of White Balance

(Fig. 6) Auto AV(CVBS) Color Balance Test Pattern (For Manual adjustment)
O Operate the zero-calibration of the CA-100, then stick
sensor to PDP module surface when you adjust.
6-3. Method of Auto AV(CVBS) Color Balance O For manual adjustment, it is also possible by the following
1) Input the PAL Composite Video (Fig6. 100% Color Bar
sequence.
Pattern) into video input.
(RCA : AV1, SCART : AV3 Input, PAL : 50Hz, NTSC : 60Hz)
1) Select white pattern of heat-run mode by pressing power
2) Set the PSM to Standard mode in Picture menu.
on key on remote control for adjustment then operate heat
3) Press INSTAR key on R/C for adjustment.
run more than 15 minutes.
4) Press the G(Vol. +) key operate to set, then it becomes
2) As below Fig.8, Supply 216Level (85 IRE) full screen
automatically.
pattern to Video input.
5) Auto-RGB OK means completed adjustment.
(RCA : AV1, SCART, AV3 Input, PAL : 50Hz, NTSC: 60Hz)
3) Press the TV/AV KEY on R/C for converting input mode.
4) Set the PSM to Standard mode in Picture menu.
5) Enter the White Balance adjustment mode by pressing the
INSTART key twice(White Balance) on R/C.

- 13 -
 6) Stick sensor to center of the screen and select each items
(Red/Green/Blue Gain and offset) using D / E(CH +/-) key
on R/C.
7) Adjust Only High Light with R Gain/ B Gain using F / G
(VOL+/-) key on R/C.
8) Adjust it until color coordination becomes as below.
(Initially, R/G/B gain and R/G/B offset values are fixed
Red Gain : 82, Green Gain : 80, Blue Gain : 86
Red Offset : 7D, Green Offset : 7E, Blue Offset : 80)
(High Light G Gain : 7A // Low Light R Offset : 7F, G Offset
7E, B Offset 80 is Fixed)
Bright : High Light : 80 ± 20cd (Fig. 9) Auto Component Color Balance Test Pattern
Color-Coordinate : High Light : X : 0.285 ± 0.003
Y : 0.295 ± 0.003
Color Temperature : 9,300°K ± 500°K 9. Auto RGB Color Balance
9) When adjustment is completed, Exit adjustment mode using [Requirement]
EXIT key on R/C It is very import to use correct adjustment pattern like fig.9
V Within the pattern, color sequence should be aligned
216 Level (85 IRE)
: W-Y-C-G-M-R-BLUE-BLACK
(If color sequence is reversed(Black -> ... > White), reverse
the pattern with REV key, when using Master pattern
generator like MSPG-925)
V If Minimum Black Level and/or Maximum White Level is not
correct, Do select 100% Color Bar Pattern.

9-1. Required Test Equipment

1) Remote controller for adjustment
(Fig. 8) Pattern for Adjustment of White Balance 2) 802F Pattern Generator
(Which has VGA 60Hz PC Format output with standard
(0.7Vpp) Vertical 16 Gray Scale pattern as Fig.10)
8. Auto Component Color Balance
[Requirement] 9-2. Method of Auto RGB Color Balance
It is very import to use correct adjustment pattern like fig.9 1) Input the PC 1024x768 60Hz 100%Color bar into RGB.
V Within the pattern, color sequence should be aligned 2) Set the PSM to Standard mode in Picture menu.
: W-Y-C-G-M-R-BLUE-BLACK 3) Press ADJ key on R/C for adjustment.
(If color sequence is reversed(Black -> ... > White), reverse 4) Press the G(Vol. +) key operate To set, then it becomes
the pattern with REV key, when using Master pattern automatically.
generator like MSPG-925) 5) Auto-RGB OK means completed adjustment.
V If Minimum Black Level and/or Maximum White Level is not
correct, Do select 100% Color Bar Pattern.

8-1. Required Test Equipment

1) Remote controller for adjustment
2) 802F Pattern Generator
(Which has 720p Ypbpr output & PC 1024x768 60Hz with
Standard(0.7Vpp) Vertical 100% Color Bar Pattern as Fig.9)

8-2. Method of auto component color balance

1) Input the Component 720p 100% Color Bar signal into
Component1 or Component2.
(Fig. 10) Auto RGB Color Balance Test Pattern
2) Set the PSM to Standard mode in Picture menu.
3) Press INSTART key on R/C for adjustment.
4) Press the G(Vol. +) key operate To set, then it becomes
automatically.
5) Auto-RGB OK means complete adjustment

- 14 -
10. Default value in adjustment mode
10-1. Auto Color Balance (Component/RGB)

Auto Color Balance(HEX)

Auto-RGB G To Set
Source Cortez
Red Offset1 22
Green Offset1 24
Blue Offset1 23
Red Offset2 45
Green Offset2 43
Blue Offset2 37
Red Gain 014
Green Gain 031
Blue Gain 011
Reset G To Set

(Fig. 11) Default Value on OSD

10-2. White Balance

White Balance(Hex)
Red Gain 82
Red Offset 80
Green Gain 86
Green Offset 7D
Blue Gain 7E
Blue Offset 80
Reset G To Set

(Fig. 12) Default Value on OSD

- 15 -
 TROUBLE SHOOTING GUIDE

1. Power Board
1-1. The whole flowchart which it follows in voltage output state

Start check

Doesn't the Yes Is it identical No Is the Interface

screen whole come with Power Off signal operated?
out? condition?

Yes Yes

No 1. Check the Power Off 2. Check the Interface

condition. signal condition.

Doesn't the Yes Doesn't the No Doesn't the No Doesn't the

low pressure output St-by 5V signal 5V Monitor signal VSC signal RL-ON
come out? come out? come out? come out?

Yes Yes Yes

No 3. Check the St-by 5V 4. Check the 5V Monitor 5. Check the VSC RL-ON
signal circuit. signal circuit. signal.

No

Doesn't the Yes Doesn't the No Doesn't the Doesn't the

high tension output VSC signal Vs-ON Vs, Va voltage output VSC low pressure
come out? come out? come out? output come out?

Yes Yes Yes

No 7. Check the VSC Vs-ON 8. Check the Vs, Va 6. Check the VSC low
signal voltage output circuit. pressure output

When the When the When the

Does Y, Z B/D Module Y B/D Module Z B/D Module
high tension Yes input connector is remove, No No
input connector is input connector is
output voltage Drop does Power Board high tension removed, does output removed, does output
occur? output voltage Drop voltage drop voltage Drop
occur? occur? occurs?
No
Yes Yes Yes

9. Check the Power 10. Check the Z B/D 11. Check the Y B/D
Manufacture enterprise Board Output high Module output circuit Module output circuit
meaning of a passage tension circuit

- 16 -
1-2. Sony Power Board Structure

T502: Vs Trans
T702: Va Trans
T101: St-by Trans
1 2 3
T103: Low Voltage Trans

- 17 -
1-3. Sanken, LGIT Power Board Structure

T221: Vs Trans
T271: Va Trans
T121: St-by Trans
1 2 3
T201: Low Voltage Trans

- 18 -
2. No Power
(1) Symptom
Ø Does’t minute discharge at module.
Ø Non does not come in into the front LED.

(2) Check following

No
Is plug in power cord? Plug in power cord.

Yes

Is the Line Filter and Power No

Connect the Cable.
Board Cable connected?

Yes

Is the Fuse(F101) on No
Replace the Fuse.
Power Board normal?

Yes

Is the Power Board and 7P of No

Connect the Cable.
VSC Board Cable connected?

Yes

After the cable connect is removed

to Power Board(except the CN101
connection cable), the AC voltage
marking is authorized on manual.
When ST-BY 5V is not operated,
replace Power Board.

- 19 -
3. Protect Mode
(1) Symptom
Ø After once shining, it does not discharge minutely
from module
Ø The Rely falls(The sound is audible “click”)

Ø It is converted with the color where the front LED

is red from green.

(2) Check following

No No
Is the Power Board Is output the normality Low/High Replace Power
normal ? voltage except Stand-by 5V? Board.

Yes

No No
Is the each connector After connecting well each connector, Replace the
normal? the normality it operates? connector.

Yes
Is the output voltage
No Yes Yes Replace
Is the Y-Board Is the Fuse(FS2) on Y-B/D normal? normal after remove
normal? (In case of open is replace) P5, P6 connector of Y-Board.
Y-B/D?
Yes
Is the output voltage
No Yes normal after remove Yes Replace
Is the Z-Board Is the Fuse (FS1, FS2) on Z-B/D
normal? normal? (In case of open is replace) P1 connector of Z- Z-Board.
B/D?
Yes
After remove P1, P2, P3 output voltage
No Is the output voltage normal after Yes
Is the X- Board normality: Replace Right X-B/D
remove P1, 2, 3, 4, 5 connector of
normal? After remove P4, P5 output voltage
X-B/D?
normality: Replace Left X-B/D
Yes

No Is the output voltage normal after Yes

Is the Ctrl Board Replace
remove P1, 2, 4, 9, 10 connector of
normal? X-Board.
Ctrl-B/D?
Yes

No Yes
Is the Is the output voltage normal after After remove P1001, 1100 normal
VSC Board normal? remove P1001, P1100? operation: Replace VSC Board

Yes

No After crisis COF of each board, check the normality operates.

Is the COF of X, Y, Z
normal ? If in case normality operates, correspondence COF Fail is
replace the module.

- 20 -
4. No Raster
(1) Symptom
Ø Does’t minute discharge at module.
Ø It maintains the condition where the front LED is green.

(2) Check following

No No
Is the Power Board Is output the normality Low/High Replace the
normal? voltage except Stand-by 5V? Power Board.

Yes

No No
Is the each connector After connecting well each connector, Replace the
normal? the normality it operates? connector.

Yes
Is the output voltage
No Yes Yes Replace
Is the Y-Board Is the Fuse(FS2) normal on Y-B/D? normal after remove
normal? (In case of open is replace) P5, P6 connector of Y-Board.
Y-B/D?
Yes
Is normal the output
No Yes Yes Replace
Is the Is the Fuse(FS1, FS2) normal on voltage after remove
Z- Board normal? Z-B/D? (In case of open is replace) P1 connector of Z-Board.
Z-B/D?
Yes
After remove P1, P2, P3 output voltage
No Is the output voltage normal after Yes
Is the normality: Replace Right X-B/D
remove P1, 2, 3, 4, 5 connector of
X- Board normal? After remove P4, P5 output voltage
X-B/D?
normality: Replace the Left X-B/D
Yes

No Is the output voltage normal after Yes

Is the Replace
remove P1, 2, 4, 9, 10 connector of
Ctrl Board normal? X-Board.
Ctrl-B/D?
Yes

No Yes
Is the Is the output voltage normal after After remove P1001, P1100 normal
VSC Board normal? remove P1001, P1100? operation: Replace the VSC Board

Yes

No After crisis COF of each board, check the normality operates.

Is the COF of X, Y, Z
normal? If in case normality operates, correspondence COF Fail is
replace the module.

- 21 -
5. In case of occurring strange screen into specific mode
5-1. In case the OSD does not displayed
(1) Symptom
Ø LED is green
Ø The minute discharged continuously becomes
accomplished from module

(2) Check following

Is the LVDS cable No Is the LVDS cable Yes

Replace the cable.
normal ? connected well?

No

Cable inserts well.

Yes

Is the VSC Board No Does the FIL8532 IC Yes

Replace VSC B/D
normal? (IC800) Operates ?

No

Replace FIL8532
Yes IC(IC800).

Is the Ctrl Board of No

Replace Ctrl B/D.
Module normal?

- 22 -
5-2. In case of does’t display the screen into specific mode
(1) Symptom
Ø The screen does not become the display from specific input mode
(RF, AV, Component, RGB, DVI).

(2) Check following

Ø Check the all input mode should become normality display.
Ø Check the Video(Main)/Data(Sub), Video(Main)/Video(Sub) should become
normality display from the PIP mode or DW mode. (Re-Check it Swap)

(3) In case of becomes unusual display from RF mode

No Is the Tuner Cable Yes Is the Input voltage, IIC Communication
Is the Tuner normal?
connected well? and CVBS output normal?

No No
Yes
Cable inserts well. Replace the Tuner

No Is the Input voltage, IIC No

Is the CXA2069Q
Communication and HV sync Replace the IC
normal?
normal?

Yes

Is the FIL8532 No Is normal the Input voltage, IIC No

Replace the IC
normal? Communication and HV sync?

(4) In the case of becomes unusual display from RF, AV mode

No Is the Input voltage, IIC No
Is the CXA2069Q
Communication and HV sync Replace the IC
normal?
normal?
Yes
No Is the Input voltage, IIC No
Is the FIL8532
Communication and HV sync Replace the IC
normal?
normal?

(5) In the case of becomes unusual display from Component, RGB mode
No Is the Input voltage, IIC No
Is the FIL8532
Communication and HV sync Replace the IC
normal?
normal?

(6) In the case of becomes unusual display from HDMI mode

No Is the Input voltage, IIC No
Is the Sil9011
Communication and HV sync Replace the IC
normal?
normal?
Yes
No Is the Input voltage, IIC No
Is the FIL8532
Communication and HV sync Replace the IC
normal?
normal?

- 23 -
6. In case of no sound
(1) Symptom
Ø LED is green
Ø Screen display but sound is not output

(2) Check following

No Yes
Is the SPK cable Is the SPK cable
Replace SPK cable
normal? connected well?

No

Yes
Cable inserts well.

No Yes Yes
Is the RF/ AV/ Does IC400 Does IC401 Does IC402
Component/ RGB/ Operates ? Operates ? Operates ?
HDMI sound normal?
No No No

Replace IC400 Replace IC401 Replace IC402

Replace
VSC B/D

- 24 -
 PRINTED CIRCUIT BOARD
MAIN(TOP)

MAIN(BOTTOM)

- 25 -
RCA(TOP) RCA(BOTTOM) CONTROL

POWER SWITCH(TOP) POWER SWITCH(BOTTOM)

- 26 -
 RCA Block Diagram
Cable

- 27 -
BLOCK DIAGRAM
 Scart Block Diagram
Cable

- 28 -
MEMO

- 29 -
 EXPLODED VIEW

300

305
301

303

530
310
302

304
200

208

207
201
202

206

540 203 205

541 204

600
501 580
102
601
230

520

220
101

103

400

- 30 -
 EXPLODED VIEW PARTS LIST

No. Part No. Descriptions

101 5900V12003C FAN, G1225S12B2-FS DONGYANG DC AXIAL 12V 120MM 1250 PRM 3P 280MM HOUSING

102 4980V01018A SUPPORTER, FAN EGI LEFT PDP DN-50PY10

103 4980V01017A SUPPORTER, FAN EGI RIGHT PDP DN-50PY10

200 6348Q-C043M PDP, 50” 1365*768 PDP50X30010.AKLGG

6348Q-C049H PDP, 50” 1365*768 PDP50X30010.ADDDB

6348Q-C049N PDP Module, 50” 1365*768 PDP50X30010.AKDDG

201 6871QCH059A PWB(PCB) ASSEMBLY,DISPLAY CTRL ASSY HAND INSERT 50X3 CTRL LGPCM1224

202 6871QDH088A PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 50X3 YDRV TOP

203 6871QDH089A PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 50X3 YDRV BOTTOM

204 6871QLH049A PWB(PCB) ASSEMBLY,DISPLAY XRLT ASSY HAND INSERT 50X3 X-LEFT(TCP)

205 6871QXH030A PWB(PCB) ASSEMBLY,DISPLAY XRCT ASSY HAND INSERT _ 50X3 X-CENTER (TCP)

206 6871QRH057A PWB(PCB) ASSEMBLY,DISPLAY XRRT ASSY HAND INSERT 50X3 X-RIGHT (TCP)

207 6871QYH039A PWB(PCB) ASSEMBLY,DISPLAY YSUS ASSY HAND INSERT FOR 50X3

208 6871QZH044A PWB(PCB) ASSEMBLY,DISPLAY ZSUS ASSY HAND INSERT FOR 50X3

220 4980900191A SUPPORTER, ASSY ADC MODULE ASSY RIGHT 50PM1M

4980900191B SUPPORTER, ASSY ADC SKD MODULE ASSY RIGHT 50PM1M

230 4980900192A SUPPORTER, ASSY ADC MODULE ASSY LEFT 50PM1M

4980900192B SUPPORTER, ASSY ADC SKD MODULE ASSY LEFT 50PM1M

300 3091V00724A CABINET ASSEMBLY, 50PM10 RF04GA NON

3091V00724B CABINET ASSEMBLY, 50PM10 RF04GA C/SKD

301 4980V00C24A SUPPORTER, FILTER EGI TOP ASSY

4980V00C24C SUPPORTER, FILTER AL MZ-50PM10 TOP SKD

302 4980V00C25A SUPPORTER, FILTER EGI BOT ASSY

4980V00C25C SUPPORTER, FILTER AL MZ-50PM10 BOT SKD

303 4980V00C27A SUPPORTER, FILTER EGI SIDE L ASSY

4980V00C27C SUPPORTER, FILTER AL MZ-50PM10 SIDE L SKD

304 4980V00C26A SUPPORTER, FILTER EGI SIDE R ASSY

4980V00C26B SUPPORTER, FILTER AL MZ-50PM10 SIDE R ASSY C/SKD

305 5230V00017B FILTER(MECH), 50PX5D-UB LGM50-03 MITSUI 50” CLASS B GLASS FILTER

310 5020V01004C BUTTON, CONTROL 42PM10 6KEY

400 3809V00502A BACK COVER ASSEMBLY, 50PM10 NO WARNING

3809V00502C BACK COVER ASSEMBLY, 50PM10 NON MZ-50PM10 SKD NO WARNING

3809V00502F Cover Assembly, MT-50PM10 NON AUSTRALIA

3809V00502L Cover Assembly, 50PM1M-TA RF052A 50” HONGKONG WITH 412-737A

501 3301900007A PLATE ASSEMBLY, AV PLATE ASSY 3300900001 3300900002 50PM10 X3

520 6871VMMF41A PWB(PCB) ASSEMBLY,MAIN RF-052A H2.MNT. MT-50PM15

530 6871VSMS70A PWB(PCB) ASSEMBLY,SUB CONT RF052A H2 50PM1M

540 6871VSME92A PWB(PCB) ASSEMBLY,SUB PSW RF043A MAILBU

541 5020900001A/ B BUTTON, POWER 50PM10/20 PC-ABS 1KEY X3 MODULE

580 6709V00001A POWER SUPPLY ASSEMBLY, 50INCH AF05GA 480W 1H259W SANKEN 50 INCH LOW END PSU

600 6871VSMAFFA PWB(PCB) ASSEMBLY,SUB RF052A H2 MONITOR RCA ATTACHABLE 1 TUNER

6871VSMANNA PCB Assembly,Sub SUB M.I RF052A 60PZ9M-TA . H2 MONITOR RCA ATTACHABLE NO TUNER

601 4980V00C30K/ P/ S SUPPORTER, AV INTERFACE EGI 50PM1MA-TA/50PM1MB-TA

- 31 -
 REPLACEMENT PARTS LIST
LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION
Q1200 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC
Q1401 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC1000 0IPRPML001A MIC39100 MICREL 3P SOT223 R/TP Q1402 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC1001 0IMCRRH001A BA033FP-E2 ROHM 3P-SOP,TO252-3 R/TP 3.3V Q201 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC1002 0IMCRFA010A KA7809R, FAIRCHILD 2P D-PAK, R/TP IC Q202 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC1003 0IPMG00027A SC156515M-1.8TR SEMTECH 5P/TO-263-5 Q203 0TR150400BA CHIP 2SA1504S(ASY) BK KEC
IC1004 0IMCRRH001A BA033FP-E2 ROHM 3P-SOP,TO252-3 R/TP 3.3V Q204 0TR150400BA CHIP 2SA1504S(ASY) BK KEC
IC1005 0IMCRRH001A BA033FP-E2 ROHM 3P-SOP,TO252-3 R/TP 3.3V Q205 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC1100 0IMCRRH001A BA033FP-E2 ROHM 3P-SOP,TO252-3 R/TP 3.3V Q207 0TR150400BA CHIP 2SA1504S(ASY) BK KEC
IC1101 0IPRPML001A MIC39100 MICREL 3P SOT223 R/TP Q300 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC1102 0IPMG00027A SC156515M-1.8TR SEMTECH 5P/TO-263-5 Q301 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC1103 0IPMGKE030A KIA78R05F KEC 5PIN DPAK R/TP 1A,5V Q302 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC1104 0IPMG00027A SC156515M-1.8TR SEMTECH 5P/TO-263-5 Q303 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC1105 0IPRPML001A MIC39100 MICREL 3P SOT223 R/TP Q304 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC1200 0IPRPS5005A SII9011CLU(PB FREE) SILICON IMAGE 128P Q305 0TR150400BA CHIP 2SA1504S(ASY) BK KEC
IC1201 0IMMRAL014B AT24C02N-10SI-2.7 ATMEL 8P SOIC R/TP Q400 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC1502 0IPMGKE030A KIA78R05F KEC 5PIN DPAK R/TP 1A,5V Q401 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC202 0IPMGON013B MC34063ADR2G ON SEMI SO-8P R/TP Q402 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC300 0ISO206900A CXA2069Q QFP64 BK I2C BUS AV S/W Q403 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC301 0ISA721700C LA7217M MFP14 TP SYNC SEPARATOR Q404 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC400 0IMCRMN028B MSP4410K MICRONAS 80P/PQFP Q405 0TR102008AA KRA102S R/TP KEC SOT23 CHIP TR
IC401 0ILNR00015A NSP-2100A,LF NEOFIDELITY TQFP 64P Q406 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC402 0IMCRTI028C TAS5122DCARG4,LF 56P/TSSOP R/TP Q407 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC407 0IPH741400E 74HC14D 14SOP TP SHITTER TRIGGER Q408 0TR102008AA KRA102S R/TP KEC SOT23 CHIP TR
IC500 0IMMRAL014B AT24C02N-10SI-2.7 ATMEL 8P SOIC
IC502 0IPH741400E 74HC14D 14SOP TP SHITTER TRIGGER DIODE
IC509 0IPRPBB005A OPA3692IDBQ BUR BROWN 16PIN SSOP D1005 0DD226239AA KDS226 TP KEC
IC600 0IPRP00009A ICL3232CBNZ INTERSIL 16P/SOP R/TP D1006 0DD226239AA KDS226 TP KEC
IC601 0IPMGKE032A KIA78R09F KEC 5PIN DPAK R/TP 1A,9V D1007 0DD226239AA KDS226 TP KEC
IC602 0IPMGKE032A KIA78R09F KEC 5PIN DPAK R/TP 1A,9V D1008 0DD226239AA KDS226 TP KEC
IC603 0IPRPNS054A LM75CIMX-3 8P/SOP R/TP D1009 0DD226239AA KDS226 TP KEC
IC800 0IMCR02005A FLI8532BD-LF GENESIS 416P/PBGA D1010 0DD226239AA KDS226 TP KEC
IC802 0IMMR00024A 24LC256T-I/SMG(PB FREE) D1012 0DD200009AF RU2M V(1) TP R-TMD 400V 1.1A 20A 0.4US
IC901 0IMMR00002A K4D261638F-LC50,LF TSOPII 66P D1013 0DD200009AF RU2M V(1) TP R-TMD 400V 1.1A 20A 0.4US
IC902 0IMMR00002A K4D261638F-LC50,LF TSOPII 66P D1100 0DD226239AA KDS226 TP KEC
D1105 0DD226239AA KDS226 TP KEC
TRANSISTOR
D1106 0DD226239AA KDS226 TP KEC
IC1202 0TR830009BA BSS83 TP PHILIPS N-CHANNEL S/W TR D1107 0DD226239AA KDS226 TP KEC
IC1203 0TR830009BA BSS83 TP PHILIPS N-CHANNEL S/W TR D1109 0DD226239AA KDS226 TP KEC
IC200 0TR830009BA BSS83 TP PHILIPS N-CHANNEL S/W TR D1110 0DD226239AA KDS226 TP KEC
IC201 0TR830009BA BSS83 TP PHILIPS N-CHANNEL S/W TR D1200 0DD184009AA KDS184 TP KEC - 85V - 300MA
IC503 0TR830009BA BSS83 TP PHILIPS N-CHANNEL S/W TR D1201 0DS113379BA 1SS133 T-72 TP ROHM KOREA DO34 90V
IC504 0TR830009BA BSS83 TP PHILIPS N-CHANNEL S/W TR D1500 0DD226239AA KDS226 TP KEC
Q100 0TR387500AA CHIP 2SC3875S(ALY) BK KEC D500 0DD226239AA KDS226 TP KEC
Q1000 0TR387500AA CHIP 2SC3875S(ALY) BK KEC D501 0DD226239AA KDS226 TP KEC
Q1001 0TR387500AA CHIP 2SC3875S(ALY) BK KEC D502 0DD226239AA KDS226 TP KEC
Q1002 0TR387500AA CHIP 2SC3875S(ALY) BK KEC D504 0DR050008AA SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
Q1003 0TR387500AA CHIP 2SC3875S(ALY) BK KEC D505 0DR050008AA SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
Q1004 0TR387500AA CHIP 2SC3875S(ALY) BK KEC D506 0DR050008AA SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
Q101 0TR387500AA CHIP 2SC3875S(ALY) BK KEC D600 0DD100009AM EU1ZV(1) TP E/EO-TMD 200V
Q101 0TR387500AA CHIP 2SC3875S(ALY) BK KEC ZD300 0DR050008AA SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
Q102 0TR102008AA KRA102S R/TP KEC SOT23 CHIP TR ZD301 0DR050008AA SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
Q102 0TR387500AA CHIP 2SC3875S(ALY) BK KEC ZD400 0DZRM00248A RLZ8.2B-TE11 R/TP LLDS(LL-34) 500MW

- 32 -
 For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film
the charactors at 2nd and 3rd CQ : Polyestor RS : Metal Oxide Film
digit in the P/No. means as CE : Electrolytic RN : Metal Film
follows; RF : Fusible

LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION

ZD600 0DR050008AA SD05.TC R/TP SEMTECH SOD323 5V 5A 15A C1159 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C1160 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
CAPACITOR
C1162 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1000 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD C1166 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1005 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD C1185 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C1007 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C1186 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C1009 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C1187 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C1010 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C1194 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
C1019 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1199 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C103 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1200 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD
C103 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1201 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD
C1030 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1225 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD
C1043 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1230 0CK105DF64A 1UF 2012 16V 20% F(Y5V) R/TP
C1046 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD C1231 0CK105DF64A 1UF 2012 16V 20% F(Y5V) R/TP
C1047 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1245 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD
C1050 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD C1247 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C1051 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD C1304 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C1064 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1306 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C1065 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1311 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1066 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1312 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1067 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1313 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1068 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1315 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1069 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1316 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C1071 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD C1317 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C1073 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD C1318 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C108 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD C1481 0CE475SK6DC 4.7UF MVG 50V 20% SMD R/TP
C1082 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1482 0CE475SK6DC 4.7UF MVG 50V 20% SMD R/TP
C1083 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1502 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
C1084 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1507 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
C1085 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1514 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1087 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD C1515 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1098 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1516 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1099 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1832 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD
C1102 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1833 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD
C1105 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1834 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD
C1107 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C204 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
C1108 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C210 0CE475SK6DC 4.7UF MVG 50V 20% SMD R/TP
C1110 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD C211 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
C1115 0CE477DJ618 470UF STD 35V 20% FL TP 5 C214 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD
C1116 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD C215 0CE105SK6DC 1UF MVG 50V 20% SMD R/TP
C1117 0CE227VF6DC 220UF MV 16V 20% R/TP(SMD) SMD C215 0CE475SK6DC 4.7UF MVG 50V 20% SMD R/TP
C1118 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD C221 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
C1119 0CE477DJ618 470UF STD 35V 20% FL TP 5 C238 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1120 0CE227VF6DC 220UF MV 16V 20% R/TP(SMD) SMD C241 0CE476SK6D8 47UF MVG,MC 50V 20% SMD TAPPING
C1126 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD C300 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C113 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD C304 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C1136 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C305 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1137 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C307 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C1138 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C315 0CK225DFK4A 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
C114 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD C318 0CK225DFK4A 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
C1148 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C319 0CK225DFK4A 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
C1156 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C320 0CK225DFK4A 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

- 33 -
For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film
the charactors at 2nd and 3rd CQ : Polyestor RS : Metal Oxide Film
digit in the P/No. means as CE : Electrolytic RN : Metal Film
follows; RF : Fusible

LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION

C335 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C837 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C337 0CE105SK6DC 1UF MVG 50V 20% SMD R/TP C838 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C342 0CE105SK6DC 1UF MVG 50V 20% SMD R/TP C839 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C368 0CK225DFK4A 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP C840 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C370 0CK225DFK4A 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP C851 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C371 0CK225DFK4A 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP C853 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C402 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C884 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C403 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD C896 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C407 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C901 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C413 0CE335VK6DC 3.3UF MV 50V 20% R/TP(SMD) SMD C904 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C418 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C905 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C419 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C930 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C421 0CK105DF64A 1UF 2012 16V 20% F(Y5V) R/TP C946 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C425 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP C947 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C444 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C952 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C451 0CK105DF64A 1UF 2012 16V 20% F(Y5V) R/TP
COIL
C456 0CK105DF64A 1UF 2012 16V 20% F(Y5V) R/TP
C457 0CE335VK6DC 3.3UF MV 50V 20% R/TP(SMD) SMD L1000 6140VB0004B 26UH 1UEWPHY 22.5TURN YL-9N 0.4
C462 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP L1101 6140VB0004B 26UH 1UEWPHY 22.5TURN YL-9N 0.4
C463 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD L1102 6140VB0004B 26UH 1UEWPHY 22.5TURN YL-9N 0.4
C464 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD L1103 6140VB0004B 26UH 1UEWPHY 22.5TURN YL-9N 0.4
C465 0CE106SK6DC 10UF MVG 50V 20% SMD R/TP L1104 6140VB0004B 26UH 1UEWPHY 22.5TURN YL-9N 0.4
C477 0CF4741L438 0.47UF D 63V 5% TP 5 M/PE NI L1124 6140VB0004B 26UH 1UEWPHY 22.5TURN YL-9N 0.4
C480 0CE108DJ618 1000UF STD 35V 20% FL TP 5 L409 6140VB0032A DBF-1015A 15.5UH 10PIE DIGITAL AUDIO
C481 0CE475SK6DC 4.7UF MVG 50V 20% SMD R/TP L410 6140VB0032A DBF-1015A 15.5UH 10PIE DIGITAL AUDIO
C482 0CE475SK6DC 4.7UF MVG 50V 20% SMD R/TP L411 6140VB0032A DBF-1015A 15.5UH 10PIE DIGITAL AUDIO
C483 0CF4741L438 0.47UF D 63V 5% TP 5 M/PE NI L412 6140VB0032A DBF-1015A 15.5UH 10PIE DIGITAL AUDIO
C484 0CF4741L438 0.47UF D 63V 5% TP 5 M/PE NI
CONNECTOR
C485 0CF4741L438 0.47UF D 63V 5% TP 5 M/PE NI
C495 0CE108DJ618 1000UF STD 35V 20% FL TP 5 C1 366-036B STAPLE
C527 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C2 6631V00045K 10P 2.5MM 550MM H-H UL1007AWG24
C545 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C3 6631V12047J 13P 1.25MM 500MM H-H UL1061AWG28
C546 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C4 6631V25032E 3P 2.5MM 300MM H-H UL1007 AWG26
C547 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C5 6631V25083G 7P 2.5MM 400MM H-H UL1007 AWG24
C548 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C6 6631V39015E 4P 3.96MM 300MM H-H UL1007AWG18
C549 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C7 6631V39016E 10P 3.96MM 300MM H-H UL1007AWG18
C550 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C8 6631V39021H 4P 3.96MM 450MM H-H UL1672AWG18
C553 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP JK401 385-173B VER TYPE . 4 . 2LINE 4P A+B
C555 0CE477VF6DC 470UF MV 16V 20% R/TP(SMD) SMD JK503 6630G70021A DV11251-PV8-PF FOXCONN 30P 2.54MM
C557 0CE477VF6DC 470UF MV 16V 20% R/TP(SMD) SMD JK601 6630VGA004B 69107-0921 MOLEX 9P 2.77MM
C559 0CE477VF6DC 470UF MV 16V 20% R/TP(SMD) SMD P1001 366-921F GIL-G-07P LGC 7PIN 2.54MM STICK
C610 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP P100A 6630VL01280 2-557100-1 AMP 80P 2.54MM PLUG
C614 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP P100B 6630VL01380 2-557101-1 AMP 80P 2.54MM RECEPTACLE
C615 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP P101 6602T12002M 53261-1390 MOLEX 13P 1.25MM R/A SMD
C620 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP P1100 366-921J GIL-G-10P LGC 10PIN 2.54MM STICK
C621 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP P400 366-932C IL-G-04P LGC 2.5MM S/T STICK
C622 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP P401 366-932B IL-G-03P LGC 2.5MM S/T STICK
C832 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP P600 366-932B IL-G-03P LGC 2.5MM S/T STICK
C833 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP P601 366-932B IL-G-03P LGC 2.5MM S/T STICK
C834 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP P800 6602T12006M 53398-1390 MOLEX 13P 1.25MM S/T SMD
C835 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP P801 6630VM01604 YW396 4P 3.96MM ANGLE, MN-60PZ12
C836 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP P802 6630VM01702 YW396 2P 3.96MM (ANGLE TYPE)

- 34 -
 For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film
the charactors at 2nd and 3rd CQ : Polyestor RS : Metal Oxide Film
digit in the P/No. means as CE : Electrolytic RN : Metal Film
follows; RF : Fusible

LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION

P803 6602T12007D GT121-31P-TD LGC 31P 1.25MM DUAL S/T L1016 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1017 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
RESISTOR
L1018 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
AR1200 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 L1019 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
AR1201 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 L102 6200JB8010L MLB-201209-1000L-N2 R/TP 1000OHM
AR1202 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 L1020 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
AR1203 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 L1021 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
AR1204 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 L1022 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
AR1205 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 L1023 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
R1112 0RS0472K607 47 OHM 2 W 5.00% TA62 L1024 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
R1113 0RS0472K607 47 OHM 2 W 5.00% TA62 L103 6200JB8010L MLB-201209-1000L-N2 R/TP 1000OHM
R230 0RD0331H609 3.3 OHM 1/2 W 5.00% TA52 L104 6200JB8010L MLB-201209-1000L-N2 R/TP 1000OHM
R618 0RD0152H609 15 OHM 1/2 W 5.00% TA52 L1106 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
R801 0RKZVTA001L 1.0M OHM 1/2 W 5% TA52 UL PILKOR L1107 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
R802 0RKZVTA001L 1.0M OHM 1/2 W 5% TA52 UL PILKOR L1108 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L111 6210VC0005A BK2125 HS 750 2X1.25X0.85MM R/TP
LED
L112 6210VC0005A BK2125 HS 750 2X1.25X0.85MM R/TP
D1003 0DL233309AC SAM2333 TP GREEN:10MCD, RED:6MCD L1125 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
D1101 0DL233309AC SAM2333 TP GREEN:10MCD, RED:6MCD L1126 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
D1102 0DL233309AC SAM2333 TP GREEN:10MCD, RED:6MCD L1127 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
D1103 0DL233309AC SAM2333 TP GREEN:10MCD, RED:6MCD L113 6210VC0005A BK2125 HS 750 2X1.25X0.85MM R/TP
D1104 0DL233309AC SAM2333 TP GREEN:10MCD, RED:6MCD L1131 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
LD101 0DL200000CA SAM5670(DL-2LRG) BK Y-GREEN - L114 6210VC0005A BK2125 HS 750 2X1.25X0.85MM R/TP
L115 6210VC0005A BK2125 HS 750 2X1.25X0.85MM R/TP
SWITCH
L116 6210VC0005A BK2125 HS 750 2X1.25X0.85MM R/TP
SW102 140-313B 2LEAD 160G(TA) 5V 0.001A HORIZONTAL .G L119 6200JB8010L MLB-201209-1000L-N2 R/TP 1000OHM
SW103 140-313B 2LEAD 160G(TA) 5V 0.001A HORIZONTAL .G L120 6200JB8010L MLB-201209-1000L-N2 R/TP 1000OHM
SW105 140-313B 2LEAD 160G(TA) 5V 0.001A HORIZONTAL .G L1204 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
SW106 140-313B 2LEAD 160G(TA) 5V 0.001A HORIZONTAL .G L1205 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
SW107 140-313B 2LEAD 160G(TA) 5V 0.001A HORIZONTAL .G L1206 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
SW108 140-313B 2LEAD 160G(TA) 5V 0.001A HORIZONTAL .G L1207 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
SW800 6600VM2006A SDDF3PATP011 250V 4A HORIZONTAL .G L1208 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
SW800 6600VR1004A SKHMPW 5P J-ALPS .V .A HORIZONTAL .G L1209 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L121 6200JB8010L MLB-201209-1000L-N2 R/TP 1000OHM
FILTER & CRYSTAL
L122 6200JB8010L MLB-201209-1000L-N2 R/TP 1000OHM
IC403 6200VJS001B ZJYS51R5-2PL(T) TDK R/TP 50VOLT 2A L137 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
IC404 6200VJS001B ZJYS51R5-2PL(T) TDK R/TP 50VOLT 2A L1501 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
IC406 6200VJS001A ZJY51R5-4P TDK DIP DC 50VOLT 2A L1502 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L100 6200JB8010L MLB-201209-1000L-N2 R/TP 1000OHM L1503 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1004 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L202 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1005 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L203 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1006 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L204 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1007 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L300 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1008 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L301 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1009 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L400 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L101 6200JB8010L MLB-201209-1000L-N2 R/TP 1000OHM L401 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1010 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L402 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1011 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L403 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1012 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L406 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1013 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L407 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1014 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L408 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1015 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L500 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM

- 35 -
LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION

L501 6210VC0005A BK2125 HS 750 2X1.25X0.85MM R/TP

L502 6200JB8010L MLB-201209-1000L-N2 R/TP 1000OHM
L503 6200JB8010L MLB-201209-1000L-N2 R/TP 1000OHM
L506 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L514 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L515 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L516 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L517 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L604 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L901 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L902 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
X1200 6212AB2845A RESONATOR,CRYSTAL ABLS-27.000MHZ
X300 166-E02F RESONATOR,CERAMIC CSBLA500KECZF09-B0
X400 156-A02M RESONATOR,CRYSTAL HC49U 18.432MHZ
X800 6212AB2844A RESONATOR,CRYSTAL ABLS-19.6608MHZ

JACK
JK101 6612VJH020C PPJ122C A/V 6P(COMPONENT)+SHIELD+GOLD
JK102 6612VJH019C PPJ121-22 A/V 4P FOR EMI WITH SWITCH RED
JK103 6612VJH020B PPJ122B A/V 6P+SHIELD+GOLD
JK104 380-363G 6046B-01S PARKELEC H=8.0 WITH S/W,SHIELD
JK105 6612JH003CA PPJ137A AUDIO L-MONO JACK
JK1200 6612B00015A DC1R019NDA JAE 1.0MM,19PIN,HDMI JACK
JK400 6612JH003CA PPJ137A AUDIO L-MONO JACK
JK502 6612F00006F KJA-PH-3-0064 KSD 3.5PHI 14P DUALJACK

ACCESSORIES
A1 3828VA0564E MANUAL, USER B/D AR/FR/EN 138L TX 114%
A1 38289U0516A MANUAL, USER EN 017M/N-TX
A2 6710T00017M REMOTE CONTROLLER, RF052A NON-EU
A3 64109EP003A POWER CORD, SP-023+IS-14 1870MM
A3 6410VBH003H POWER CORD, 003D-G/SOURCING 2800MM

MISCELLANEOUS
CA1 68509A0002A CABLE,COAXIAL 150MM KCA-NS-0-0053 KSD
CA2 6850J00005C CABLE,DVI LVDS UL20276 AWG30 600MM
F801 0FS1002B53K FUSE, 10000MA 250 V 5.2X20
IC900 6927V1298AH SOFT WARE, 3.11V 59B6 1366X768
PA101 6712000002B REMOTE CONTROLLER RECEIVER,KSM-603SM12E-1
TU201 6700MF0012C TUNER, TAFM-W103P LGIT MULTI FS

- 36 -
 Apr., 2006
P/NO : 3828VD0223T Printed in Korea