Programmable DC Power

Supply
IT6900 Series User Manual

Model: IT6922A/IT6932A/IT6933A/IT6942A/
IT6952A/IT6953A/IT6922B/IT6932B/
IT6933B/IT6942B/IT6952B/IT6953B
Version: V5.8
Statement Guarantee
© Itech Electronic, Co., Ltd. 2022 Materials in the document are provided Safety Statement
No part of this manual may be talis qualis and may be changed in
reproduced in any form or by any means future revisions without prior notice. In
(including electronic storage and addition, within the maximum allowable “Caution” signs indicate danger. It is
retrieval or translation into a foreign extent of laws, ITECH is not committed required to pay attention to the contents
language) without prior permission and to any explicit or implied guarantee for of these signs during implementation of
written consent from Itech Electronic, this manual and all information therein, operations.
Co., Ltd. as governed by international including but not limited to the implied The damage to the product or loss of
guarantee on marketability and important data may be caused in case of
copyright laws.
availability for some special purposes. improper operation steps or failure to
Manual Article No. ITECH shall not be responsible for any follow operation steps. Do not continue
error or incidental or indirect losses to implement any improper operation
IT6900-402178 caused by the provision, use or indicated in “Caution” signs when the
application of this documents and specified conditions are not fully
Revision
information therein. If some guarantee understood or these conditions are not
Revision 5, published on clauses in other written agreements satisfied.
Nov. 22th 2022 between ITECH and users are not
consistent with clauses herein, those
Itech Electronic, Co., Ltd. clauses in other written agreements
Trademark Statement shall prevail.
Technology license “Warning” indicates danger. It is required
Pentium is a registered trademark of to pay attention to the contents of these
Intel Corporation in the United States. Hardware and/or software in this signs during implementation of
document cannot be provided without a operation steps. Personal casualties
Microsoft, Visual Studio, Windows and license and can only be used or copied may be caused in case of improper
MS Windows are trademarks of according to the license. operation steps or failure to follow these
Microsoft Corporation in the United operation steps. Do not continue to
States and/or other countries/regions. Restricted permission statement implement any improper operation
indicated in “Warning” signs when the
Restricted permissions of the U.S.
specified conditions are not fully
government. Permissions for software
understood or these conditions are not
and technical data which are authorized
satisfied.
to the U.S. Government only include
those for custom provision to end users.
ITECH follows FAR 12.211 (technical
data), 12.212 (computer software).
DFARS 252.227-7015 (technical Note
data--commercial products) for national
defense and DFARS 227.7202-3 “Instructions” indicates operation
(permissions for commercial computer instructions. It is required to refer to the
software or computer software contents of these signs during operation
documents) while providing the steps. These signs are used for
customized business licenses of providing tips or supplementary
software and technical data. information for operators.
 IT6900 User Manual

Certification and Quality Assurance

IT6900 series power supply completely reaches nominal technical indicators in
the manual.

Warranty Service
ITECH Company will provide one-year warranty services for the product
materials and manufacturing (excluding the following limitations).
 When warranty service or repair is needed, please send the product to the
service unit specified by ITECH Company.
 When the product is sent to ITECH Company for warranty service, the
customer must pay the one-way freight to the maintenance department of
ITECH, and ITECH will be responsible for return freight.
 If the product is sent to ITECH for warranty service from other countries,
the customer will be responsible for all the freight, duties and other taxes.

Limitation of Warranty
This Warranty will be rendered invalid in case of the following:
 Damage caused by circuit installed by customer or using customer own
products or accessories;
 Product which has been modified or repaired by the customer;
 Damage caused by circuit installed by customer or not operating our
products under designated environment;
 The product model or serial number is altered, deleted, removed or made
illegible by customer;
 Damage caused by accidents, including but not limited to lightning, water,
fire, abuse or negligence.

Safety Signs
Direct current ON (power)

Alternating current OFF (power)

Both direct and alternating Power-on state

current

Protective earth (ground) Power-off state

terminal

Earth (ground) terminal Reference terminal

Copyright ©ITECH Electronic Co., Ltd. i

 IT6900 User Manual

Caution Positive terminal

Warning (refer to this manual Negative terminal

for specific Warning or
Caution information)

A chassis terminal - -

Safety Precautions
General safety precautions below must be followed in each phase of instrument
operation. In case of failure to follow these precautions or specific warnings in
other parts of the manual, violation against the safety standards related to the
design, manufacture and purpose of the instrument will occur. If the user does
not follow these precautions, ITECH will bear no responsibility arising there
from.

 The power supply is provided with a three-core power cord during delivery
and should be connected to a three-core junction box. Before operation, be
sure that the power supply is well grounded.
 Use electric wires of appropriate load. All loading wires should be capable
of bearing maximum short-circuit of electronic load without overheating.
 Ensure the voltage fluctuation of mains supply is less than 10% of the
working voltage range in order to reduce risks of fire and electric shock.
 To prevent burnout, please pay special attention to positive and negative
polarities of power supply during connection!
 Do not use damaged equipment. Please check the housing before using
the equipment. Check whether the instrument is subject to cracking or is
lack of plastic. Do not operate the instrument in the environment with
explosive gas, steam or dust.
 Observe all tags on the equipment before connection.
 Do not install alternative parts on the instrument or perform any
unauthorized modification.
 Do not use the equipment when the removable cover is dismantled or
loose.
 Please use the power adapter supplied by the manufacturer to avoid
accidental injury.
 We do not accept responsibility for any direct or indirect financial damage
or loss of profit that might occur when using the instrument.
 This instrument is used for industrial purposes. Do not apply this product to
IT power supply system.
 Do not use the equipment on the life support system or other equipment
with safety requirements.

Copyright ©ITECH Electronic Co., Ltd. ii

 IT6900 User Manual

 If the equipment is not used in the manner specified by the manufacturer,

its protection may be damaged.
 Always use dry cloth to clean the equipment housing. Do not clean the
inside of the instrument.
 Do not block the air vent of the equipment.

Environmental Conditions
The IT6900 series power supply can only be used indoors or in low
condensation areas. The following table shows general environmental
requirements for this instrument.
Environmental conditions Requirement
Operating temperature 0°C - 40°C
Operating humidity 20% - 80% (non condensing)
Storage temperature -20°C - 70 °C
Altitude Operating up to 2,000 meters
Pollution Grade 2 pollution
Installation category
Ⅱ

Note

To make accurate measurements, allow the instrument to warm up for 30 min before
operation.

Regulation Tag
The CE tag shows that the product complies with the
provisions of all relevant European laws (if the year is
shown, it indicates that the year when the design is
approved).

The UKCA tag shows that the product complies with the
provisions of all relevant United Kingdom laws (if the year
is shown, it indicates that the year when the design is
approved).

Copyright ©ITECH Electronic Co., Ltd. iii

 IT6900 User Manual

This instrument complies with the WEEE directive

(2002/96/EC) tag requirements. This attached product
tag shows that the electrical/electronic product cannot be
discarded in household waste.

This symbol indicates that no danger will happen or

toxic substances will not leak or cause damage in
normal use within the specified period. The service life
of the product is 10 years. The product can be used
safely within the environmental protection period;
otherwise, the product should be put into the recycling
system.

Waste Electrical and Electronic Equipment (WEEE)

Directive
Waste electrical and electronic equipment (WEEE) directive,
2002/96/EC
The product complies with tag requirements of the WEEE directive
(2002/96/EC). This tag indicates that the electronic equipment
cannot be disposed of as ordinary household waste.
Product Category
According to the equipment classification in Annex I of the WEEE
directive, this instrument belongs to the “Monitoring” product.
If you want to return the unnecessary instrument, please contact
the nearest sales office of ITECH.

Copyright ©ITECH Electronic Co., Ltd. iv

 IT6900 User Manual

Compliance Information
Complies with the essential requirements of the following applicable European
Directives, and carries the CE marking accordingly:
 Electromagnetic Compatibility (EMC) Directive 2014/30/EU
 Low-Voltage Directive (Safety) 2014/35/EU

Conforms with the following product standards:

EMC Standard
IEC 61326-1:2012/ EN 61326-1:2013 ¹²³
Reference Standards
CISPR 11:2015+A1:2016 Ed 6.1
IEC 61000-3-2: 2018 RLV
IEC 61000-3-3: 2013+A1:2017
IEC 61000-4-2:2008
IEC 61000-4-3 2006+A1:2007+A2:2010/ EN 61000-4-3 A1:2008+A2:2010
IEC 61000-4-4:2012
IEC 61000-4-5:2014+A1:2017
IEC 61000-4-6:2013+cor1:2015
IEC 61000-4-11:2004+A1:2017

1. The product is intended for use in non-residential/non-domestic environments. Use of the

product in residential/domestic environments may cause electromagnetic interference.
2. Connection of the instrument to a test object may produce radiations beyond the specified
limit.
3. Use high-performance shielded interface cable to ensure conformity with the EMC
standards listed above.

Safety Standard
IEC 61010-1:2010+A1:2016

Copyright ©ITECH Electronic Co., Ltd. v

 IT6900 User Manual

Content
Certification and Quality Assurance ........................................................................................................... i
Warranty Service ........................................................................................................................................ i
Limitation of Warranty ................................................................................................................................. i
Safety Signs................................................................................................................................................ i
Safety Precautions ..................................................................................................................................... ii
Environmental Conditions .......................................................................................................................... iii
Regulation Tag ........................................................................................................................................... iii
Waste Electrical and Electronic Equipment (WEEE) Directive.................................................................. iv
Compliance Information ................................................................................................. 错误!未定义书签。

Chapter1 Inspection and Installation .................................................................................................. 1

1.1 Verifying the Shipment......................................................................................................................... 1

1.2 Instrument Size Introduction ................................................................................................................ 1
1.3 Rack Mounting ..................................................................................................................................... 5
1.4 Connecting the Power Cord ................................................................................................................ 5

Chapter2 Quick Start............................................................................................................................. 6

2.1 Brief Introduction ................................................................................................................................. 6

2.2 Introduction to Front Panel .................................................................................................................. 7
2.3 Key Introduction ................................................................................................................................... 8
2.4 VFD Description .................................................................................................................................. 8
2.5 Introduction to Rear Panel ................................................................................................................... 9
2.6 Power-on Self-test ............................................................................................................................. 11

Chapter3 Function and Features ....................................................................................................... 14

3.1 Local/Remote Mode .......................................................................................................................... 14

3.2 Voltage Setup .................................................................................................................................... 14
3.3 Current Setup .................................................................................................................................... 14
3.4 On/Off Operation ............................................................................................................................... 15
3.5 Setup value/Actual value ................................................................................................................... 15
3.6 Voltage/Current/Power adjustment .................................................................................................... 15
3.7 Saving Operation ............................................................................................................................... 15
3.8 Trigger Operation ............................................................................................................................... 16
3.9 Menu Operation ................................................................................................................................. 16
3.10 OVP Function .................................................................................................................................. 24
3.11 Key Lock .......................................................................................................................................... 24
3.12 Rear Pins Function .......................................................................................................................... 24
3.12.1 Remote sense and DVM terminals ........................................................................................... 24
3.12.2 RS485 and Output Sync signal interface.................................................................................. 26
3.13 Analog Control Interface .................................................................................................................. 26

Chapter4 Remote Operation Mode .................................................................................................... 28

4.1 RS232 interface ................................................................................................................................. 28

4.2 USB interface .................................................................................................................................... 30
4.3 GPIB interface (IT6900(G) series only) ............................................................................................. 30
4.4 RS485 interface ................................................................................................................................. 30

Copyright ©ITECH Electronic Co., Ltd. vi

 IT6900 User Manual

Chapter5 Technical Specification ...................................................................................................... 32

5.1 Major Technical Parameters .............................................................................................................. 32

5.2 Supplemental Characteristics ............................................................................................................ 38

Appendix .................................................................................................................................................... 39

Specifications of Red and Black Test Lines ............................................................................................. 39

Copyright ©ITECH Electronic Co., Ltd. vii

 Inspection and Installation

Chapter1 Inspection and Installation

1.1 Verifying the Shipment

Unpack the box and check the contents before operating the instrument. If
wrong items have been delivered, if items are missing, or if there is a defect
with the appearance of the items, contact the dealer from which you purchased
the instrument immediately. The package contents include:
Checklist of Package Contents
Item Qty. Model Remarks
The IT6900 series include:
IT6922A/IT6932A/IT6933A/
IT6900 power IT6942A/IT6952A/IT6953A/
x1 IT6900 series
supply
IT6922B/IT6932B/IT6933B/

IT6942B/IT6952B/IT6953B

User may select an appropriate

power cord that matches the
IT-E171/IT-E172
specifications of power socket
Power cord x1 /IT-E173/IT-E17
used in the area. See the Section
4
Connecting the Power Cord for
details.

USB cable x1 - -

Ex-factory Test It is the test report of the

x1 -
Report instrument before delivery.

NOTE

After confirming that package contents are consistent and correct, please appropriately
keep package box and related contents. The package requirements should be met when
the instrument is returned to factory for repair.

IT6900 series power supply is supplied with the following optional accessories
(sold separately):

Item Model Remarks

IT-E151A (Rack IT-E151A To mount the instrument on a special rack,
mount kit) user may select this optional.

1.2 Instrument Size Introduction

The instrument should be installed at well-ventilated and rational-sized space.
Copyright ©ITECH Electronic Co., Ltd. 1
 Inspection and Installation

Please select appropriate space for installation based on the electronic load
size.
IT6900 series power supply different models are not the same size, the detail
size of the power supply is shown as below.
IT6922A/IT6932A/IT6942A/IT6922B/IT6932B/IT6942B Models

Detailed Dimension Drawing

Copyright ©ITECH Electronic Co., Ltd. 2

 Inspection and Installation

IT6933A/IT6933B Models

Detailed Dimension Drawing

Copyright ©ITECH Electronic Co., Ltd. 3

 Inspection and Installation

IT6952A/IT6953A/IT6952B/IT6953B Models

Detailed Dimension Drawing

Copyright ©ITECH Electronic Co., Ltd. 4

 Inspection and Installation

1.3 Rack Mounting

IT6900 series power supply can be mounted on a standard 19” rack. ITECH
provides user with IT-E151A rack, an optional mount kit.

1.4 Connecting the Power Cord

Connect power cord of standard accessories and ensure that the power is
under normal power supply.

AC power input level

Working voltage of IT6900 series includes 110V and 220V (which can be
selected by the switch at the bottom of power supply).
AC power input level:
 Option Opt.01: 220VAC ± 10%, 47 to 63 Hz
 Option Opt.02: 110 VAC ± 10%, 47 to 63 Hz

Categories of power lines

Select from the flowing schedule of power cord specifications an appropriate
power cord that matches the voltage for the area in which you use the
instrument. If the power cord included in the instrument you purchased does
not match the voltage, contact the dealer or manufacturer for change.

China United States & Europe England

Canada & Japan
IT-E171 IT-E173 IT-E174
IT-E172

Copyright ©ITECH Electronic Co., Ltd. 5

 Quick Start

Chapter2 Quick Start

This chapter introduces the front panel, the rear panel, key functions and VFD
display function of the power supply, make sure that you can quickly know the
appearance, instruction and the key function before you operate the power
supply. Help you make better use of this series of power supply.

2.1 Brief Introduction

IT6900 series power supplies are high performance single-output
programmable DC power supplied with communication interface. This series of
programmable DC power supply can output the maximum voltage or current
with a fixed power for customers. Take IT6922A (60V/5A/100W) for example,
when you select 60V for the output voltage, the output power of IT6922A is
100W, so in this case the maximum output current is 100W/60V = 1.66A. When
you select 20V for the output voltage, the maximum output current 100W/20V =
5A, but when the output voltage is down to 10V, due to IT6922A maximum
current is 5A, so in this case the maximum output current is 5A. IT6900 series
power comes with a standard communication interface RS232/USB/RS485,
both desktop and system-based features, can be designed and tested
according to your needs and provide multi-purpose solutions.

Convenient bench-top features:

 High visibility vacuum fluorescent display (VFD)
 Digital keyboard operation
 High accuracy and high resolution
 Low ripple and low noise
 Intelligent fan control, energy conservation, noise reduction
 Standard communication interface RS232/USB/RS485
 Can be monitored by computer software
 Output voltage and current values accordance with procedure
 Can use the knob to adjust the voltage and current
 Can adjust the numbers steps using the cursor
 Rich SCPI orders to facilitate the formation of intelligent test platform
 Can set the output timer (0.1 ~ 99999.9s)
 External Analog Control Interface

Model Voltage Current Power

IT6922A IT6922A(G) 60V 5A 100W
IT6932A IT6932A(G) 60V 10A 200W

Copyright ©ITECH Electronic Co., Ltd. 6

 Quick Start

IT6933A IT6933A(G) 150V 5A 200W

IT6942A IT6942A(G) 60V 15A 360W
IT6952A IT6952A(G) 60V 25A 600W
IT6953A IT6953A(G) 150V 10A 600W
IT6922B IT6922B(G) 60V 5A 100W
IT6932B IT6932B(G) 60V 10A 200W
IT6933B IT6933B(G) 150V 5A 200W
IT6942B IT6942B(G) 60V 15A 360W
IT6952B IT6952B(G) 60V 25A 600W
IT6953B IT6953B(G) 150V 10A 600W

* IT6922B/IT6932B/IT6933B/IT6942B/IT6952B/IT6953B have standard RS485

communication interface and external Analog control Interface.
*IT6900(G) is the model with built-in GPIB, the function is the same as standard
model, please check with ITECH for availability.

2.2 Introduction to Front Panel

The front panel of IT6900 series is shown in the next figure.

1. VFD display
2. Rotary knob
3. Compound key, the local switch key and power switch
4. Number keys and ESC
5. Function keys
6. UP/DOWN/LEFT and RIGHT key, to move cursor
7. Output terminals

Copyright ©ITECH Electronic Co., Ltd. 7

 Quick Start

2.3 Key Introduction

Key description, see the table below:

Keys Name and the function
Compound key, co-work with OVP, Menu, Save, DVM,
(Shift) Trigger, Lock
Local switch key, switch from remote mode to local
(Local) operation mode.

(Power) Power on key

0-9 Numeric keys

. Decimal point
V-set Voltage set key, set the output voltage/over voltage
/OVP protection point for the power supply.

I-set Current set key, set the output current/menu function key,
/Menu to set the relevant Parameters for the power supply.
Callback key to call up a set value of system parameters
Recall /Save already stored / storage key, to save system parameter
settings.
Meter key, to switch from value set panel and the actual
Meter /DVM output value display / voltage meter function keys, to
switch to the measure state of the voltage meter.
Enter /Trigger Enter key, to confirm the number entered and operation /
trigger button, which is used to trigger the List test.
On/Off Output on (off) keys, control power output state / keypad
/Lock lock function keys, used to lock the panel buttons.
Left and right movement keys, used to set the value, to
adjust the cursor to the specified location.
Up and down keys, used to select a item in the menu or
increase (decrease) the output voltage or current
values.

Cancel /return keys.

2.4 VFD Description

Copyright ©ITECH Electronic Co., Ltd. 8

 Quick Start

Char Function description Char Function description

OFF Output is off Timer Output on timer function is ON

The power supply is in
CV Sense No
constant voltage mode
The power supply is in
CC Ext No
constant current mode
(USB GPIB) light when the
* No Adrs address match or (RS232)
received order
The power supply is in remote
Meter “Meter” on state Rmt
mode
The power supply has error or
Shift Use compound keys Error
fault
OVP OVP function state on Prot OVP OTP Protection
Key operation is locked by
OCP No Lock
Password

2.5 Introduction to Rear Panel

 The rear panel of IT6922A/IT6932A/IT6933A/IT6942A is shown in the next
figure.

1. Cooling window
2. RS232 Communication cable interface
3. USB Communication cable interface
4. GPIB Communication cable interface (IT6900(G) series only)
5. DVM input terminal, Remote measurement terminal and the output
terminal
6. AC power socket (fuse contained)

Copyright ©ITECH Electronic Co., Ltd. 9

 Quick Start

 The rear panel of IT6952A/IT6953A is shown in the next figure.

1. Cooling window
2. RS232 Communication cable interface
3. USB Communication cable interface
4. GPIB Communication cable interface (IT6900(G) series only)
5. Remote measurement terminal and DVM input terminal
Attention: The + and - terminals here are only used for shorting
between S+ and S-, not the output terminals, so do not connect to
the DUT.
6. Output terminal
7. Fuse
8. AC power socket

 The rear panel of IT6922B/IT6932B/IT6933B/IT6942B is shown in the next

figure.

1. Cooling window
2. RS232 Communication cable interface
3. USB Communication cable interface
4. GPIB Communication cable interface (IT6900(G) series only)
5. AC power socket (fuse contained)
6. Output Sync signal interface and RS485 Communication cable
interface
7. DVM input terminal, Remote measurement terminal and the output
terminal
Copyright ©ITECH Electronic Co., Ltd. 10
 Quick Start

8. Analog control interface

 The rear panel of IT6952B/IT6953B is shown in the next figure.

1. Cooling window
2. RS232 Communication cable interface
3. USB Communication cable interface
4. Output Sync signal interface and RS485 Communication cable
interface
5. GPIB Communication cable interface (IT6900(G) series only)
6. Analog control interface
7. Remote measurement terminal and DVM input terminal
Attention: The + and - terminals here are only used for shorting
between S+ and S-, not the output terminals, so do not connect to
the DUT.
8. Output terminal
9. Fuse
10. AC power socket

2.6 Power-on Self-test

A successful self-test indicates that the purchased power product meets
delivery standards and is available for normal usage.
Before operation, please confirm that you have fully understood the safety
instructions.

 To avoid burning out, be sure to confirm that power voltage matches with
supply voltage.
 Be sure to connect the main power socket to the power outlet of protective
grounding. Do not use terminal board without protective grounding. Before
operation, be sure that the power supply is well grounded.
 To avoid burning out, pay attention to marks of positive and negative
polarities before wiring.

Copyright ©ITECH Electronic Co., Ltd. 11

 Quick Start

Self-test steps
Normal self-test procedures:
1. Correctly connect the power cord. Press Power key to start up.
2. After self-test, if the power supply is normal, then VFD will display the
output voltage and current status as below:

OFF

0.000V 0.0000A

Error Information References

The following error information may occur when an error occurs during Power
On self-test:
 If the EEPROM was damaged or the latest operation data in EEPROM was
lost, the VFD will display “EEPROM FAIL”.
 If the last power status in EEPROM is lost, then the VFD will display “SYST
LOST”.
 If the calibration data in EEPROM is lost, the VFD display the tooltip
information “CAL LOST”.
 If the factory calibration data in EEPROM is lost, and then the VFD will
display “FACT LOST”.

Exception handling
If the power supply cannot start normally, please check and take measures by
reference to steps below.
1. Check whether the power cord is correctly connected and confirm whether
the power supply is powered.
Correct wiring of power cord => 2
Incorrect wiring of power cord => Re-connect the power cord and check
whether the exception is removed.

2. Check whether the power in On. Power key is under “ ” On status.

Yes => 3
No => Please check the Power key to start power and check whether the
exception is removed.
3. Check whether the fuse of power supply is burned out.
If yes, change fuse. Detailed steps:
1) Pull out power line and take out the fuse box at power line jack with a
small screw driver. As shown below.

Copyright ©ITECH Electronic Co., Ltd. 12

 Quick Start

2) If the fuse is fused, please change fuse of same specification based on

machine model. See the table blow for matching information of fuse
and machine model.

Products Specification (110VAC) Specification (220VAC)

IT6922A T5A 250V T2.5A 250V
IT6932A T6.3A 250V T3.15A 250V
IT6933A T6.3A 250V T3.15A 250V
IT6942A T10A 250V T6.3A 250V
IT6952A T15A 250V T10A 250V
IT6953A T15A 250V T10A 250V
IT6922B T5A 250V T2.5A 250V
IT6932B T6.3A 250V T3.15A 250V
IT6933B T6.3A 250V T3.15A 250V
IT6942B T12.5A 250V T6.3A 250V
IT6952B T15A 250V T10A 250V
IT6953B T15A 250V T10A 250V

3) After replacement, install the fuse box back to original position, as

shown below.

NOTE

Fuse of IT6952A/IT6953A/IT6952B/IT6953B can unscrew directly by hand.

Copyright ©ITECH Electronic Co., Ltd. 13

 Function and Features

Chapter3 Function and Features

3.1 Local/Remote Mode

Local button can enable you switch mode from remote to local mode.
After you power on the power supply, unit will default in local mode, all the
buttons can be used in this mode. While in remote mode, you can’t operate
through front panel directly. Local and remote mode can be controlled through
PC. In addition, the mode changing will not influence the output parameters.

3.2 Voltage Setup

You can set voltage within the range of rated voltage value. When you press
V-set button, the button will be lit. This indicates that you can set voltage.
There are three ways to set output voltage through front panel.

 The first way: press V-set ,adjust cursor location through

button, pressing and will enable you to adjust the

setting voltage value.

 The second way: press V-set , adjust cursor location through

button, adjust rotary knob to change the setting voltage

value.

V-set 0 9
 The third way: press button and number key( to ) to set
voltage value.

3.3 Current Setup

You can set current within the range of rated current value. When you press
I-set button, the button will be lit. This indicates that you can set current.
There are three ways to set output current through front panel.

 The first way: press I-set ,adjust cursor location through

button, push and will enable you to adjust the setting

current value.

Copyright ©ITECH Electronic Co., Ltd. 14

 Function and Features

 The second way: press I-set ,adjust cursor location through

button, adjust rotary knob to change the setting current

value.

I-set 0 9
 The third way: press button and number key( to ) to set
current value.

3.4 On/Off Operation

On/Off button is used to control the output state of power supply. When
On/Off button is lit, this indicates the output is in on mode. When output is
open, the working state indicator light(CV/CC) will be lit.
Note: make sure you have connected power supply well, then press On/Off
button.

3.5 Setup value/Actual value

You can switch the display between setting value and actual value by

pressing Meter button. When this button is lit, screen displays actual output
value and the indicator light “meter” will be lit on the VFD board. In other words,
when the button is not lit, the front panel displays setting value.

3.6 Voltage/Current/Power adjustment

The output current value is determined by output voltage of power supply and
electronic load’s resistance. Only when the actual current value is lower than
the setting current value, can power supply work in CV mode and the will CV
indicator light be lit.
If output current is higher than the setting value, then power supply will function
in CC mode. And the CC indicator light will be lit.
The output voltage and current value are also influenced by the upper limit of
output power. Take IT6932A (60V/10A/200W) for example, suppose you set the
max power value to be 200W, then when the setting output voltage and current
is 25V/10A, in fact, the unit can only output 25V/8A.

3.7 Saving Operation

Customer can save some often-used parameters in nonvolatile memory. You

can use the button + Recall (Save) button or SCPI order *SAV, *RCL to
achieve this function. Saving parameters include: setting voltage/setting current

Copyright ©ITECH Electronic Co., Ltd. 15

 Function and Features

Saving method:

Press + Recall (save) button, and then input the group number you want
to save through number key board. Press enter button to confirm. If you want to
recall the saved parameters, press Recall button and corresponding group
number (number1-9).At last press enter button to confirm.

3.8 Trigger Operation

You need to select the trigger mode from the menu before using this function.

After you edit a list file, press + Enter (Trigger) to give a trigger signal.

During the running process, Enter button will be lit all the time.

3.9 Menu Operation

Press + I-set (Menu) to enter the menu. You will see a optional items on
the screen, through direction keys and rotary knob to upturn VFD display, then
the screen will display the following functions .Press Enter button will enter
ESC
corresponding items. Press button will return to previous menu.

IT6922A/IT6932A/IT6933A/IT6942A/IT6952A/IT6953A power supply menu

function is shown as below.
MAX VOLT Set the max output voltage
OCP SET OFF Disable the over current protection function.
ON Enable the over current protection function.
SYST SET Reset Power is restored to factory setting
P-MEN (RESET)
Keep Set the power-on state as the last power off state
OFF Enable the power-on output state to be off mode
P-OUT (OFF) Set the power-on output state to be the last
Keep
power-off output state
GPIB(IT6900(G)
ADDR Address can be set within 0-30
series only)
4800
9600
19200
BAUD
38400
COMM (GPIB)
57600
RS232
115200
NONE 8BIT
NONE 8BIT EVEN 8BIT
ODD 8BIT
MODE SIGNAL
Copyright ©ITECH Electronic Co., Ltd. 16
 Function and Features

ADDR. Address can be set

MUX
within 0-30
USB
OFF Close the key sound
BEEP (ON)
ON Open the key sound
LOCK Lock the rotary knob function
KNOB (ON)
ON Unlock the rotary knob function
MANU Local keyboard trigger
TRIG (MANUAL)
BUS External trigger
MEM (GROUP1) GRP1-8 Save and recall operation

SLOW AD speed is low speed

ADC SPEED MID AD speed is middle speed

FAST AD speed is high speed

In the voltage/current setting state (or the LOCK
state to view the set value), if there is no operation
WAIT 5 S
in 5S, it will automatically return to the
METER RETURN
measurement state.
It does not automatically return to the
NO
measurement state.
OFF Close the timer function
TIMER SET Open the timer operation, the time can be set
ON
within 0.1-99999.9s
NO keep the original setting
RESET
YES restore the factory setting
EXIT Quit the menu setting
LIST SET OFF Close list test function
LIST STATE
ON Open list test function
LIST LOAD Recall the saved list file(FILE0-FILE9)
SEC second
TIME (SEC)
MIN minute
VSET Setup the single step voltage
ISET Setup the single step current
SEC Setup single step delay time(0.1-9999)
LIST EDIT YES continue the edit of next step
NEXT (YES)
NO End up the list file edit
REPET 1-65535 Set the cycle time of list file
NO Do not save the current list file
SAVE Save the list file to appointed
FILE0-FILE9
document
EXIT Quit the system menu
POWER MODEL Unit model
INFO VER The software version
SN-1 The first six number of SN
Copyright ©ITECH Electronic Co., Ltd. 17
 Function and Features

SN-2 The middle six number of SN

SN-3 The last six number of SN
EXIT Quit the information menu
EXIT MENU Quit the main menu

IT6922B/IT6932B/IT6933B/IT6942B/IT6952B/IT6953B power supply menu

function is shown as below.
MAX VOLT Set the max output voltage
OCP SET OFF Disable the over current protection function.
ON Enable the over current protection function.
SYST SET Reset Power is restored to factory setting
P-MEN (RESET)
Keep Set the power-on state as the last power off state
OFF Enable the power-on output state to be off mode
P-OUT (OFF) Set the power-on output state to be the last
Keep
power-off output state
GPIB(IT6900(G)
ADDR Address can be set within 0-30
series only)
4800
9600
19200
BAUD
38400
57600
115200
RS232
NONE 8BIT
NONE 8BIT EVEN 8BIT
ODD 8BIT
SIGNAL
MODE ADDR. Address can be set
MUX
within 0-30
COMM (GPIB)
USB
4800
9600
19200
BAUD
38400
57600
115200
RS485
NONE 8BIT
NONE 8BIT EVEN 8BIT
ODD 8BIT
SIGNAL
MODE ADDR. Address can be set
MUX
within 0-30
BEEP (ON) OFF Close the key sound
Copyright ©ITECH Electronic Co., Ltd. 18
 Function and Features

ON Open the key sound

LOCK Lock the rotary knob function
KNOB (ON)
ON Unlock the rotary knob function
OFF Disable external signal control function
Ext-C ANA Enable external analog control function
DIGIT Enable external digital control function
MANU Local keyboard trigger
TRIG (MANUAL)
BUS External trigger
MEM (GROUP1) GRP1-8 Save and recall operation

SLOW AD speed is low speed

ADC SPEED MID AD speed is middle speed

FAST AD speed is high speed

In the voltage/current setting state (or the LOCK
state to view the set value), if there is no operation
WAIT 5 S
in 5S, it will automatically return to the
METER RETURN
measurement state.
It does not automatically return to the
NO
measurement state.
OFF Close the timer function
TIMER SET Open the timer operation, the time can be set
ON
within 0.1-99999.9s
NO keep the original setting
RESET
YES restore the factory setting
EXIT Quit the menu setting
LIST SET OFF Close list test function
LIST STATE
ON Open list test function
LIST LOAD Recall the saved list file(FILE0-FILE9)
SEC second
TIME (SEC)
MIN minute
VSET Setup the single step voltage
ISET Setup the single step current
SEC Setup single step delay time(0.1-9999)
LIST EDIT YES continue the edit of next step
NEXT (YES)
NO End up the list file edit
REPET 1-65535 Set the cycle time of list file
NO Do not save the current list file
SAVE Save the list file to appointed
FILE0-FILE9
document
EXIT Quit the system menu
POWER MODEL Unit model
INFO VER The software version
SN-1 The first six number of SN
SN-2 The middle six number of SN
Copyright ©ITECH Electronic Co., Ltd. 19
 Function and Features

SN-3 The last six number of SN

EXIT Quit the information menu
EXIT MENU Quit the main menu

NOTE

ESC
Pressing button can enable you to quit any function setting.

Maximum voltage set (>MAX VOLT)

The range of setting voltage is from 0V to rated voltage. You can press +

I-set (Menu) button to enter the menu, then press direction key to

select >MAX VOLT item. Press Enter button to confirm. After you set the
max voltage value, the output voltage value can only be set less than the max
voltage. Our default max voltage value is the rated value.

Power-on parameters set (>P-MEN)

This item can set power on state of parameters. If you select RESET item, then
all the parameters will be initialized to the factory setting. Output voltage and
current will always be 0V/0A. Or the output value will be the same with last
power off state. The default setting is RESET item.

Power On Output State (>P-OUT)

This item can set the power on output state. If you select keep item, that
indicates the power on output state is the same with last power off output state.
If you select off item, unit will automatically in off mode when you power on.
Default setting is OFF item.

Communication (>COMM)
Our unit has provided standard communication interfaces: RS232/USB. In this
option, you can select the communication interface according to your demands.
The range of GPIB (IT6900(G) series only) address is 0-30. Besides, we have
multi-baud rate to be chosen in RS232 mode 4800, 9600, 19200, 38400, 57600,
11.52K. Data bit is 8,Check digit have three choices: NONE, ODD, EVEN.
Before you begin to carry out communication, please make sure the configure
in our unit agrees with PC configure.

Key Sound Set (>BEEP ON)

This item can set the key sound state. If in on mode, then key sound will be
there when you press buttons. If in off mode, the beeper will not make a sound.
The default set is in on mode.

Copyright ©ITECH Electronic Co., Ltd. 20

 Function and Features

Rotary Knob Set (>KNOB)

This item is used to set rotary knob state. In on mode, you can use this rotary
knob to set the output value and overturn the menu items. In lock mode, this
knob can’t be used. The default setting is in on mode.

External Signal Control Function (>Ext-C)

(IT6922B/IT6932B/IT6933B/IT6942B/IT6952B/IT6953B Specific function)
This item is used to enable or disable signal control. When OFF is selected,
function is disabled; when ANA (analog control) is selected, external analog
control function is enabled; when DIGIT (digit control) is selected, external digit
control function is enabled. The default set is in OFF option. This function will
be described in details below.

Trigger mode (>TRIG)

Before you running a list file, you need a trigger signal. Thus you must set the
trigger mode firstly, in keyboard trigger mode or in external trigger mode. In

MANU trigger mode, press + Enter button can generate a trigger

signal. In BUS trigger mode, you can only through sending orders to trigger.
The default set is MANU option.

Group Set (MEM GROUP)

Power supply can save some often-used parameters in a nonvolatile memory
(capacity is 9*8 groups). This function can make the operations more
convenient. Customer can save and recall parameters quickly.

GRP1: This indicates saving power supply parameters in 1-9 groups. Press

+ Recall (Save) and the group number (1-9) can save the parameters in
corresponding groups.

GRP2: This indicates saving the parameters in 10-18 groups. Press +

Recall (Save)+saved group number(1-9) can save related parameters. Note
that the current number “1” represents parameters are saved in 10th groups.
Number “2” represents the parameters are saved in 11th groups.
GRP3-GRP8 by parity of reasoning.

AD Speed Set (>ADC SPEED)

This item is used to set the AD speed, i.e., measurement display speed of
power supply. There are three kinds of AD speed, including SLOW, MID and
FAST. Ex-factory set is in SLOW option.

Copyright ©ITECH Electronic Co., Ltd. 21

 Function and Features

NOTE
When AD speed of power supply is set to MID or FAST, the measurement accuracy is too
low to reach the middle accuracy in the specification. Only when AD speed of power
supply is set to SLOW can the middle accuracy in the specification be reached.

Timer Set (>TIMER SET)

This item is used to set the “time on- load” function. In ON mode, the indicator
light “Timer” will be lit on the VFD screen. When output of power supply is
opened, timer will begin to work, after reaching the definite time, output will be
off automatically. If in OFF mode, the timer function will not be enabled. The
default set is in OFF option.

Reset (>RESET)
This item is used to reset all items in the menu. If you select >YES, then unit will
be restored to factory setting. If you select >NO, all setting in the menu will
remain unchanged.

List Mode (>List Set)

Before you edit a list file, please set the trigger mode: manual mode.

Press + I-set button to enter the menu, then press direction key to

select >SYST SET option, after that please push Enter button to confirm. At
last please press direction key to select >Trig MANUAL and push Enter
button to confirm.
You can make the output change order by editing every step value of list
operation. The parameters you need to edit includes: single-step voltage,
single-step current, single-step delay time and whether to go on the next step.
Besides, you also need to set the repeat times and save list sequence file. After
you finish the editing process, at this time if you receive a trigger signal, power
supply will begin to work according to the sequence steps you’ve edited. Now
we take five steps for an example:
Operation steps:

1. Press + I-set (Menu) button to enter the menu

2. VFD display >MAX VOLT, press to select >LIST SET, press Enter to
confirm

3. VFD display >LIST STATE, press to select >LIST EDIT, press Enter

to confirm
4. VFD display >TIME SEC, press Enter to confirm, go to the next step,

you can also through button to select >TIME MIN time unit, press
Enter to confirm.

Copyright ©ITECH Electronic Co., Ltd. 22

 Function and Features

0 9
5. VFD display >VSET 0.000, press number key to or through
rotary knob to set voltage, after that press Enter to confirm.

0 9
6. VFD display ISET 0.0000, press number key to or rotary knob to
set the single-step current, press Enter to confirm.

0 9
7. VFD display SET 0.1, press number key to or rotary knob to set
single-step delay time, press Enter to confirm.
8. VFD display NEXT >YES, press Enter to confirm.
9. Repeat the steps from 5) to 8) and set the four steps’ voltage/current and
delay time separately. When screen display NEXT>YES in the fourth step

edit process, please press to select NEXT >NO, press Enter to

confirm.

0 9
10. VFD display REPET 1, press number key to or rotary knob to set
the repeat times, press Enter to confirm.
11. VFD display SAVE >NO, press Enter to confirm, in this circumstance,

the list file is not saved but can run for one time, or you can press
button to select >SAVE FILE0, saving the list test file in FILE0~FILE9,
press Enter to confirm. You can recall the file in the following utilization.
12. If you do not save the list test file, VFD will display LIST EDIT; if you select
to save the test file, VFD will display SAVE DONE for three seconds, and
then display LIST EDITL.

13. Press to select >LIST STATE item, press Enter to confirm.

14. VFD display LIST >OFF, press to select >LIST >ON, press Enter to

confirm. Now Enter button will be lit. This indicates that list operation
function has been opened.

Esc
15. VFD display >LIST STATE, pressing button can quit the operation.

16. Press On/Off button to open the output, press + Enter (Trigger) to
give a trigger signal.
17. If you have edited several list files, you can select LIST LOAD item to recall
Esc
the file you need. And then press to quit this operation. Press
On/Off button to open the output. Now you only need to press

+ Enter (Trigger) to give a trigger signal, the list file can be ran.

18. In LIST mode, voltage set and current set button can’t be used, In LIST
Copyright ©ITECH Electronic Co., Ltd. 23
 Function and Features

STATE item, choose LIST>OFF will enable you to quit list mode.

3.10 OVP Function

IT6900 series power supply provide OVP function, press + V-set button
can enable you to set the over voltage protection value. Over voltage may
caused by internal defect or customer’s incorrect operation(such as output
voltage rising),or external voltage too high. Once power supply is
protected(OVP), the output will be off immediately and “OVP” indicator light will
be lit, the VFD display “OVER VOLT”.
Avoid external voltage that across the output terminals exceeding the 120% of
rated voltage or it will damage out power supply!
When power supply in OVP state, please check the external factors first, after
you exclude the external factors, press ON/OFF button to open output again. If
in communication state originally, you should by sending order OUTP ON order
to open output.

3.11 Key Lock

Press + On/Off (Lock) button to set the key lock state. If keyboard has
been locked, the indicator light LOCK will display on the VFD screen. In
addition, when key board are lock, all buttons can’t be used but ON/OFF, Meter
button, shift button. Press this button once again will relieve key lock function.

3.12 Rear Pins Function

3.12.1 Remote sense and DVM terminals

 +, - : output terminals, the same with front panel output terminals.

 S+, S-: remote sense pins.
 V+, V-: the output interface of a four semi-digital voltmeter. (The actual
terminal position on the rear panel of IT6952A/IT6953A/IT6952B/IT6953B
is subject to the actual product. The above figure is only used as an
example to introduce the terminal function.)

Copyright ©ITECH Electronic Co., Ltd. 24

 Function and Features

Digital Volt Meter (DVM)

IT6900 series power supply has four semi-digital voltmeter. This DVM can

measure 0.001V to 61.000V voltage. Press + Meter (DVM) button can

enable the measured value display on the VFD screen. Press any key to quit
the display of this value.

Remote sense function

Remote sense can adjusted at the output voltage of the device under test, this
feature allows to compensate the voltage drop on the wire between the front
panel terminals of the power supply and the device under test.
 Use local sense:
Local sense doesn’t compensate the voltage drop on the connection wire, the
operation is:
1. Use the short clips on the back panel of the instrument, or install wire
between + and S+, - and S-.
2. Connect the positive and negative terminals of the front panel to the device
under test.
 Use remote sense:
Remote sense compensate the voltage drop on the connection wire, the
operation is:
1. Disconnect the wires/short clips between + and S+, - and S-.
2. Connect wires from S+, S- to the device under test.
3. Connect wires from +, - to the device under test (Except
IT6952A/IT6953A/IT6952B/IT6953B).

For IT6952A/IT6953A/IT6952B/IT6953B:

Copyright ©ITECH Electronic Co., Ltd. 25

 Function and Features

NOTE

In order to ensure the stability of the system, using armored twisted pair cable between
the remote sense terminal of IT6900 and load.

Please note that the positive and negative polarity when wiring, otherwise it will damage
the instrument!

3.12.2 RS485 and Output Sync signal interface

Terminals on IT6922B/IT6932B/IT6933B/IT6942B/IT6952B/IT6953B power
supply rear board comprise Output Sync signal interface and RS485
communication interface, as shown below.

 +,-: Output Sync signal terminal

 A, B: RS485 communication interface

DC source output indication function:

There is a Output Sync terminal which is used to indicate the output state of DC
source at the rear panel. When in output on mode, Output Sync terminal will
output a high level. When in off mode, Output Sync terminal will output a low
level.

RS485 communication interface

RS485 communication interface is often used for multiple devices control.

Press shift + I-set button to entry into the menu, user need to set the
parameters of Baud rate, Data bit, Stop bit, parity bit and address, the setting is
the same with RS232 communication setting.

3.13 Analog Control Interface

IT6922B/IT6932B/IT6933B/IT6942B/IT6952B/IT6953B power supply output
can be controlled and monitored by external DC voltage source (0~10V).

Copyright ©ITECH Electronic Co., Ltd. 26

 Function and Features

If external analog control is not used, it must be disabled before normal front
panel operation can resume. Follow the steps below to enable or disable
external analog control.(Entry into the system menu----Enter button to
confirm-----select Ext-C item---choose ANA item and enable this mode. If
choose DIGIT, it means enable the external digital control function.)
Pin # Label Description
1 REF_10V 10V DC reference output
2 Vs/D0 Composite terminal: Voltage programming input/
Digital D0 input terminal
3 Is/D1 Composite terminal: Current programming input/
Digital D1 input terminal
4 D2 Digital D2 input terminal
5 ON/OFF Control output state
6 Vm Voltage monitoring output
7 Im Current monitoring output
8 NULL None
9 GND Ground pin

Copyright ©ITECH Electronic Co., Ltd. 27

 Remote Operation Mode

Chapter4 Remote Operation Mode

IT6900A series power supply has standard communication interface:
RS232, USB, and IT6900B series power supply has standard
communication interface: RS232, USB, RS485. The user can choose any
one of them to implement a communication with the computer.

4.1 RS232 interface

There is a DB9 connector at the rear of the power supply, when connect to
computer, you need to connect a cable with COM port on both side. To active

connection, you need to set the front panel composite key + I-set

key configuration settings the same as computer configuration settings.

RS-232 interface can be used to program all of the SCPI orders.

NOTE

The RS232 settings must match the settings in front panel system information. If any

change, please press + I-set key.

RS-232 data format

RS-232 data is a 10-bit words which has a start bit and a stop bit. The start bit
and stop bit cannot be edited. However, you can select the parity items with

+ I-set key on the front panel. Parity options are stored in nonvolatile
memory.

Baud Rate

The front panel + I-set button allows the user to select a baud rate
which is stored in the non-volatile memory: 4800 /9600/ 19200 /38400/
57600 /115200.

RS-232 connection cable

Use a RS232 cable with DB-9 interface, RS-232 serial port can connect
with the controller (e.g. PC). Do not use blank Modem cable.
If your computer is using a RS-232 interface with DB-25 connector, you
need an adapter cable with a DB-25 connector at one end and the other
side is a DB-9(not blank modem cable)

Copyright ©ITECH Electronic Co., Ltd. 28

 Remote Operation Mode

Base pin Description

number
1 No conjunction
2 TXD, data transmission
3 RXD, data receiving
RS232 Pins of Plug 4 No conjunction
5 GND, grounding
6 No conjunction
7 CTS, clear to send
8 RTS, request to send
9 No conjunction

RS-232 Troubleshooting:
If there is RS-232 connection problem, check the following:
 Computer and power supply must configure the same baud rate,
parity, data bits and flow control options. Note that the power
configuration as a start bit and a stop bit (these values are fixed).
 As described before in RS-232 connector, you must use the correct
interface cable or adapter. Note that even if the cable has the right
plug, the internal wiring may be wrong.
 Interface cable must be connected to the correct serial port on the
computer (COM1, COM2, etc.).

Communication Settings
Before communication, you should first make the following parameters of
power supply and PC matches.
Baud Rate: 9600 (4800,9600,19200,38400,57600,115200). You can
enter the system menu from the front panel, and then set the baud rate.
Calibration (none, even, odd)
EVEN 8 data bits, have even parity
ODD 8 data bits have odd parity
NONE 8 data bits, no parity
Mode: SIGNAL, MUX
SIGNAL (Single connection mode)
MUX (Multiple connection mode) ADDR: Local address (0 to 30, the
factory default setting is 0)

Start Bit 8 Data Bits Parity=None Stop Bit

Copyright ©ITECH Electronic Co., Ltd. 29

 Remote Operation Mode

4.2 USB interface

Use a Cable with two USB port to connect the power and the computer.
All power functions can be programmed via USB.
The USB488 interface functions of the power supply described as below:
 Interface is 488.2 USB488 interface.
 Interface Receiver REN_CONTROL, GO_TO_LOCAL, and
LOCAL_LOCKOUT request.
 Interface receive MsgID = TRIGGER USBTMC order information,
and will pass TRIGGER order to the functional layer.
Power USB488 device functions described as follows:
 Devices can read all of the mandatory SCPI orders.
 Device is SR1 enabled.
 Device is RL1 enabled.
 Device is DT1 enabled.

4.3 GPIB interface (IT6900(G) series only)

First, Connect the GPIB interface on the power supply and the GPIB
card on computer via IEEE488 bus, must be full access and tighten the
screws. Then set the address, the address range of the power : 0 to 30,

can set by the function key on the front panel, press the + I-set key
to enter the system menu function, find the GPIB address setting by
▼ Enter
button, type the address, key to confirm. GPIB address is
stored in nonvolatile memory line.

4.4 RS485 interface

IT6922B/IT6932B/IT6933B/IT6942B/IT6952B/IT6953B power supply, via the
RS485 interface, provides multi-unit control function for up to 30 units (If
connecting more than 10 units, add a 120Ω resistor terminator to the last unit).

On the front panel, press (Shift)+ I-set keys to enter into the system
menu, and the related setting is the same as the RS232 communication setting.
User can set the following parameters of the RS485 interface:
Baud rate: 9600(4800/9600/19200/38400/57600/115200)
Parity and data bit: NONE/8BIT, EVEN/8BIT, ODD/8BIT
EVEN 8 data bits, have even parity
ODD 8 data bits have odd parity
NONE 8 data bits, no parity
Copyright ©ITECH Electronic Co., Ltd. 30
 Remote Operation Mode

Mode: SIGNAL (Single connection mode)

MUX (Multiple connection mode) ADDR: Local address (0 to 30, the
factory default setting is 0)

Start Bit 8 Data Bits Parity=None Stop Bit

To set the multi-unit connection mode, access the system Menu→SYST

SET→COMM→RS485→MODE→MUX, to turn on the chain mode.

Set each unit with a different Address (0 to 30). Then by using RS485, connect
the first power supply in the chain to a PC. Now, multiple units daisy-chained
via RS485 can be controlled by one PC by using the commands specific for
multi-unit connection. See “Programming Guide” section for details.
The figure below is a schematic diagram of the connection of 4 machines.

Connect PC

Copyright ©ITECH Electronic Co., Ltd. 31

 Technical Specification

Chapter5 Technical Specification

This chapter will introduce the main technical parameters of IT6900,such as
rated voltage/current/power and so on. Besides, we will introduce the working
environment and storage temperature.

5.1 Major Technical Parameters

Parameters IT6922A IT6932A IT6942A
voltage 0~60V 0~60V 0~60V
Rated values
current 0~5A 0~10A 0~15A
(0 °C~40 °C)
Power 100W 200W 360W

Load regulation voltage ≤0.01%+3mV ≤0.01%+10mV ≤0.01%+30mV

±(%of output+offset) current ≤0.05%+2mA ≤0.05%+4mA ≤0.05%+6mA

Line regulation voltage ≤0.01%+3mV ≤0.01%+10mV ≤0.01%+30mV

±(%of output+offset) current ≤0.05%+2mA ≤0.05%+4mA ≤0.05%+6mA
voltage 1mV 1mV 1mV
Setup resolution
current 0.1mA 1mA 1mA
voltage 1mV 1mV 1mV
Readback resolution
current 0.1mA 1mA 1mA
Setup accuracy
voltage ≤0.03%+5mV ≤0.03%+5mV ≤0.03%+5mV
(within twelve months)
(25°C±5°C)
current ≤0.1%+5mA ≤0.1%+10mA ≤0.1%+15mA
±(%of output+offset)
Read back resolution
voltage ≤0.03%+5mV ≤0.03%+5mV ≤0.03%+5mV
(within twelve
months) (25°C±5°C)
current ≤0.1%+5mA ≤0.1%+10mA ≤0.1%+15mA
±(%of output+offset)
Ripple voltage ≤5mVp-p ≤8mVp-p ≤15mVp-p
(20Hz ~20MHz) current ≤5mArms ≤6mArms ≤8mArms

Sample rate 10HZ

Dimension (mm) 214.5mmW×88.2mmH×354.6mmD

Weight (net) 7.7Kg

Copyright ©ITECH Electronic Co., Ltd. 32

 Technical Specification

Parameters IT6933A
voltage 0-150V
Rated values
current 0-5A
(0 °C~40 °C)
Power 200W
voltage 220VAC ±10%/110VAC ±10%
AC Input
Frequency 47 Hz ~63Hz
Maximum input current 2A
Maximum input apparent
500VA
power
Efficiency 0.55
Power Factor 0.7
Load regulation voltage ≤0.01%+20mV
±(%of output+offset) current ≤0.01%+6mA
Line regulation voltage ≤0.01%+20mV
±(%of output+offset) current ≤0.01%+6mA
1mV(<100V),
voltage
Setup resolution 10mV(≥100V)
current 0.1mA
1mV(<100V),
voltage
Readback resolution 10mV(≥100V)
current 0.1mA
Setup accuracy voltage ≤0.04%+30mV
(within twelve months)
(25°C±5°C) current ≤0.1%+10mA
±(%of output+offset)
Read back resolution voltage ≤0.04%+30mV
(within twelve months)
(25°C±5°C) current ≤0.1%+10mA
±(%of output+offset)
voltage ≤30mVp-p
Ripple(20Hz ~20MHz)
current ≤6mArms
Rise time(No-load) voltage 200ms
Rise time(Full-load) voltage 300ms
Fall time(No-load) voltage 2s
Fall time(Full-load) voltage 150ms
Transient Response Time 200us
Remote Sense
1V
Compensation
Command Response Time 10~600ms
Difference-mode
50mV
voltage(Vpp)
Difference-mode current
20mA
(Arms)
Setup Temp.coefficient voltage 50 PPM/°C +30mV
Copyright ©ITECH Electronic Co., Ltd. 33
 Technical Specification

( 0 °C~40 °C) current 50 PPM/°C+30mA

Readback Temp.coefficient voltage 50 PPM/°C+30mV
( 0 °C~40 °C) current 50 PPM/°C+30mA
Working temperature 0-40°C
Storage temperature -10-70°C
Series number 2
Parallel number 2
Isolation(output to ground) 240V
Dimension (mm) 214.5mmW×88.2mmH×354.6mmD
Weight (net) 7.7Kg

Parameters IT6952A IT6953A

voltage 0~60V 0~150V
Rated values
current 0~25A 0~10A
(0 °C~40 °C)
Power 600W 600W

Load regulation voltage ≤0.01%+30mV ≤0.01%+25mV

±(%of output+offset) current ≤0.1%+10mA ≤0.05%+10mA

Line regulation voltage ≤0.01%+30mV ≤0.01%+25mV

±(%of output+offset) current ≤0.1%+10mA ≤0.05%+10mA
1mV(<100V)
voltage 1mV
Setup resolution 10mV(>100V)
current 1mA 1mA
1mV(<100V)
voltage 1mV
Readback resolution 10mV(>100V)
current 1mA 1mA
Setup accuracy
voltage ≤0.03%+5mV ≤0.03%+20mV
(within twelve months)
(25°C±5°C)
current ≤0.1%+25mA ≤0.1%+25mA
±(%of output+offset)
Read back resolution
voltage ≤0.03%+5mV ≤0.03%+20mV
(within twelve months)
(25°C±5°C)
current ≤0.1%+25mA ≤0.1%+25mA
±(%of output+offset)
Ripple voltage ≤20mVp-p ≤50mVp-p
(20Hz ~20MHz) current ≤15mArms ≤15mArms

Sample rate 10HZ

Dimension (mm) 214.5mmW×88.2mmH×445mmD

Weight (net) 15Kg

Copyright ©ITECH Electronic Co., Ltd. 34

 Technical Specification

Parameters IT6922B IT6932B

voltage 0~60V 0~60V
Rated values
current 0~5A 0~10A
(0 °C~40 °C)
Power 100W 200W

voltage ≤0.01%+3mV ≤0.01%+10mV

Load regulation
±(%of output+offset)
current ≤0.05%+2mA ≤0.05%+4mA

Line regulation voltage ≤0.01%+3mV ≤0.01%+10mV

±(%of output+offset) current ≤0.05%+2mA ≤0.05%+4mA

voltage 1mV 1mV

Setup resolution
current 0.1mA 1mA

voltage 1mV 1mV

Readback resolution
current 0.1mA 1mA

Setup accuracy
voltage ≤0.03%+5mV ≤0.03%+5mV
(within twelve months)
(25°C±5°C)
current ≤0.1%+5mA ≤0.1%+10mA
±(%of output+offset)
Read back resolution
voltage ≤0.03%+5mV ≤0.03%+5mV
(within twelve months)
(25°C±5°C)
current ≤0.1%+5mA ≤0.1%+10mA
±(%of output+offset)

voltage ≤5mVp-p ≤8mVp-p

Ripple
(20Hz ~20MHz)
current ≤5mArms ≤6mArms

Sample rate 10HZ

Dimension (mm) 214.5mmW×88.2mmH×354.6mmD

Weight (net) 7.7Kg

Parameters IT6933B
voltage 0~150V
Rated values
current 0~5A
(0 °C~40 °C)
Power 200W
Load regulation voltage ≤0.01%+20mV
±(%of output+offset) current ≤0.01%+6mA

Copyright ©ITECH Electronic Co., Ltd. 35

 Technical Specification

Line regulation voltage ≤0.01%+20mV

±(%of output+offset) current ≤0.01%+6mA
1mV(<100V)
voltage
10mV(≥100V)
Setup resolution
current 0.1mA

1mV(<100V)
voltage
Readback resolution 10mV(≥100V)
current 0.1mA
Setup accuracy voltage ≤0.04%+30mV
(within twelve months)
(25°C±5°C) current ≤0.1%+10mA
±(%of output+offset)
Read back resolution voltage ≤0.04%+30mV
(within twelve months)
(25°C±5°C) current ≤0.1%+10mA
±(%of output+offset)
Ripple voltage ≤30mVp-p
(20Hz ~20MHz) current ≤6mArms

Rise time(No-load) voltage ≤200mS (10%-90%)

Rise time(Full-load) voltage ≤300mS(10%-90%)

Fall time(No-load) voltage ≤2S(90%-10%)

Fall time(Full-load) voltage ≤150mS(90%-10%)

Transient Response
50%-100% load recovery to 75mV (Freq=1K) 200us
Time
Remote Sense
1V
Compensation
Setup
50ppm/℃+30mV
voltage
Readback
50ppm/℃+30mV
Temp.coefficient voltage
(0 °C~40 °C) Setup
50ppm/℃+30mA
current
Readback
50ppm/℃+30mA
current
Sample rate 10HZ/S
Working temperature 0℃～40℃
Storage temperature -10℃～70℃
Insulation voltage of
240V
the output to ground
Dimension (mm) 214.5mmW×88.2mmH×354.6mmD
Weight (net) 7.7Kg

Copyright ©ITECH Electronic Co., Ltd. 36

 Technical Specification

Parameters IT6942B IT6952B

voltage 0~60V 0~60V
Rated values
current 0~15A 0~25A
(0 °C~40 °C)
Power 360W 600W

Load regulation voltage ≤0.01%+30mV ≤0.01%+30mV

±(%of output+offset) current ≤0.05%+6mA ≤0.1%+10mA

Line regulation voltage ≤0.01%+30mV ≤0.01%+30mV

±(%of output+offset) current ≤0.05%+6mA ≤0.1%+10mA

voltage 1mV 1mV

Setup resolution
current 0.1mA 0.1mA
voltage 1mV 1mV
Readback resolution 0.1mA(<10A) 0.1mA(<10A)
current
1mA(>10A) 1mA(>10A)
Setup accuracy
voltage ≤0.03%+5mV ≤0.03%+5mV
(within twelve months)
(25°C±5°C)
current ≤0.1%+15mA ≤0.1%+25mA
±(%of output+offset)
Read back resolution
voltage ≤0.03%+5mV ≤0.03%+5mV
(within twelve months)
(25°C±5°C)
current ≤0.1%+15mA ≤0.1%+25mA
±(%of output+offset)
Ripple voltage ≤15mVp-p ≤20mVp-p
(20Hz ~20MHz) current ≤8mArms ≤15mArms
Rise time voltage ≤150mS(10%-90%) ≤150mS(10%-90%)
Fall time voltage ≤2S(10%-90%) ≤2S(10%-90%)

Sample rate 10HZ/S 10HZ/S

214.5mmW×88.2mmH×
Dimension (mm) 214.5mmW×88.2mmH×354.6mmD
445mmD
Weight (net) 7.7Kg 15Kg

Parameters IT6953B
voltage 0~150V
Rated values
current 0~10A
( 0 °C~40 °C)
power 600W
Load regulation voltage ≤0.01%+25mV
±(%of output+offset) current ≤0.5%+10mA
Line regulation voltage ≤0.01%+25mV
±(%of output+offset) current ≤0.5%+10mA
Copyright ©ITECH Electronic Co., Ltd. 37
 Technical Specification

voltage 1mV(<100V) 10mV(≥100V)

Setup resolution
current 0.1mA
voltage 1mV(<100V) 10mV(≥100V)
Readback resolution
current 0.1mA
Setup accuracy voltage ≤0.03%+20mV
(within twelve
months) (25°C±5°C) current ≤0.1%+25mA
±(%of output+offset)
Read back resolution voltage ≤0.03%+20mV
(within twelve months)
(25°C±5°C) current ≤0.1%+25mA
±(%of output+offset)
Ripple voltage ≤50mVp-p
(20Hz ~20MHz) current ≤15mArms
Rise time voltage ≤150mS(10%-90%)
Fall time voltage ≤7S(90%-10%)
Transient voltage
0.2mS
Response Time
Sample rate 10HZ/S
Dimension(mm) 214.5mmW×88.2mmH×445mmD
Weight (net) 15Kg

*The above specifications may be subject to change without prior notice.

5.2 Supplemental Characteristics

State storage capacity: 9×8 Groups
Recommended calibration frequency: once a year
Cooling style: fans
Maximum input power:
Model Maximum input power Model Maximum input power
IT6922A 350VA IT6942A 1000VA
IT6932A 550VA IT6952A 2000VA
IT6933A 550VA IT6953A 2000VA
IT6922B 350VA IT6932B 550VA
IT6942B 1000VA IT6952B 2000VA
IT6953B 2000VA IT6933B 550VA

Copyright ©ITECH Electronic Co., Ltd. 38

 Appendix

Appendix

Specifications of Red and Black Test Lines

ITECH provides you with optional red and black test lines, which individual
sales and you can select for test. For specifications of ITECH test lines and
maximum current values, refer to the table below.
Model Specification Cross section Length
IT-E301/10A 10A - 1m
IT-E301/30A 30A 6mm2 1.2m
IT-E301/30A 30A 6mm2 2m
IT-E301/60A 60A 20mm2 1.5m
IT-E301/120A 120A 50mm2 2m
IT-E301/240A 240A 70mm2 1m
IT-E301/240A 240A 70mm2 2m
IT-E301/360A 360A 95mm2 2m

For maximum current of AWG copper wire, refer to table blow.

AWG 10 12 14 16 18 20 22 24 26 28
The 40 25 20 13 10 7 5 3.5 2.5 1.7
Maximum
current
value( A)
Note: AWG ( American Wire Gage), it means X wire ( marked on the wire). The
table above lists current capacity of single wire at working temperature of 30°C.
For reference only.

Copyright ©ITECH Electronic Co., Ltd. 39

Contact Us
Thanks for purchasing ITECH products. In case of any doubts, please contact us as follows:
1. Visit ITECH website: www.itechate.com
2. Select the most convenient contact method, for further information.