YOUR LIFE, HEYBIKE

HEYBIKE CITYSCAPE2.0
ELECTRIC BIKE

AIPAS-A2
ELECTRIC BIKE
COPYRIGHT 2024 AIPAS.ALL RIGHTS RESERVED.
INSTRUCTION MANUAL
The manufacturer reserves the right to make changes to the product and manual at any time
Visit www.Aipasbike.com to download the latest user manuals
USER MANUAL
 CONTENTS AIPAS EBIKE

Aipas eBike 01 Please read the instruction manual carefully before setting up your eBike and
riding. You should be familiar with the operation of your eBike, its features,
Safety Messages 02 capabilities, and limitations. To ensure a long, trouble-free life for your Aipas
eBike, provide it with the proper care and maintenance as described in this
Icons and Stickers Guide 07 manual. Of course, it is not practical or possible to warn you about all of the
hazards associated with operating or maintaining your Aipas eBike. For this,
Note Before Assembly 09 you must use your own good judgment.
Product Overview 10
For any replacement parts and accessories, Please use Aipas eBikes-approved
Setting Up Your Aipas eBike 11 parts, as they have been specially designed for your bicycle and manufac-
tured to meet Aipas eBikes’ demanding standards.
Specifications 17
This manual should be considered a permanent part of your bicycle and
LCD Display Controls 18 should remain with the bicycle when it is sold.

Functions 21 Please contact us if you need any assistance please do not hesitate to reach
out to us.
Warning Messages 25
Thinks To Know Before The Ride 28 CONTACT INFORMATION
Battery Safety 30 Email: [email protected]

Charge Safety 33 Website:www.aipasbike.com

Storing The Battery 35 Pre-sales Phone:1(833)556-3566

After-sales Phone:1(833)532-5966
Troubleshooting 36
Active your warranty and get more info by
@AipasEbike
Maintenance 37
scanning this QR code

Legal Warranty 39
FCC 42

00 01
 Safety Messages Safety Messages

Please record your bicycle’s serial number in the space below. The serial Read Manual Before Riding
number is located on the head tube of your bicycle. Refer to page 09 for the Please read the manual before you take the ride on your new eBike and keep it for reference. This
location of the serial number. Owner’s Manual contains important safety, performance, and service information.
Like any sport, bicycling involves the risk of injury and damage. By choosing to ride a bicycle, you
SERIAL NUMBER assume the responsibility of that risk: you need to know and practice the rules of safe and
responsible riding as well as proper use and maintenance. Proper use and maintenance of your
bicycle reduces the risk of injury. If you have any questions or do not understand any aspect of
using or maintaining your bike, take responsibility for your safety and consult with your local
bicycle shop, or contact us for assistance.
This manual is not intended as a comprehensive use, service, repair, or maintenance manual.
Please see your local bicycle shop for all service, repairs, or maintenance. Your local bicycle shop
may also be able to refer you to classes, clinics, or books on bicycle use, service, repair, and main-
tenance.
Your Aipas eBike is classified as an EPAC (Electrically Power Assisted Cycle, otherwise known as
a Pedelec), and is referred to in this manual as a bicycle unless otherwise noted.

Rider's Responsibility Regarding Regulations

It is the rider’s responsibility to obey the regulations that apply to your Aipas eBike.
The regulations covering the use of your Aipas eBike vary by state and even municipality in
certain locations. You must comply with the local regulations related to the minimum age of the
rider, driver’s license, insurance, license plate, traffic, maximum speed regulations, and any other
regulations. These regulations may change at any time.

Intended Use
The intended use of your Aipas eBike is to be ridden by one rider at an appropriate time and
place for general transportation or recreational use. Any other use is prohibited and may result
in SERIOUS INJURY or DEATH.
Your bicycle is NOT INTENDED for off-road or mountain bicycle use or any kind of jumping. Some
of these bicycles have suspension features, but these features are designed only to add comfort,
not off-road capabilities.
Riders should be proficient cyclists (ages 16+), riding on paved surfaces where the tires are always
on the ground, on roadways, or dedicated bicycle-only lanes where permitted by law (not on
pedestrian-use shared lanes or sidewalks). Your bicycle should not be used to tow another
bicycle. For trailer towing, consult this Owner’s Manual and the trailer owner’s manual for towing
instructions and towing compatibility.

02 03
 Safety Messages Safety Messages

WARNING! Helmets
To prevent serious injury or death: Always wear a helmet. Wearing a helmet properly may reduce the risk of a severe head injury.
Read all safety warnings and all instructions. When riding, always wear a helmet that meets or exceeds the standards of the Consumer
Product Safety Commission(CPSC). Check the manual that comes with your helmet.
Always ride within your limits and the limits of your eBike.
Ensure your helmet fits your head and is properly secured. If you attach a child's seat to the
Bicycles are only for use by persons 16 years old and above. bicycle, the child must wear a properly fitted helmet at all times.
Riders must have the physical coordination, reaction, and mental capabilities to control a Read your helmet manual to make sure it is adjusted properly according to the fitting instruc-
bicycle and manage traffic, in addition to managing road conditions and sudden situations tions provided by the helmet manufacturer.
with respect to the laws and instructions governing bicycle use. Persons with any mental or
A proper-fitting helmet should be comfortable and should neither rock forward/backward
physical conditions that may make them susceptible to injury, impair their physical dexterity
nor side to side.
or mental capabilities to recognize, understand, and follow safety instructions —or understand
the hazards inherent to its use — should not use or be permitted to use products inappropriate
for their abilities.
Pre-Ride safety Check
Never ride under the influence of drugs and/or alcohol. Before each ride, inspect your eBike for damage. If damage is found, do not ride.

Consult a doctor before using the device if you have any medical condition or issue that affects Verify that the front and rear axles are secure.
your ability to safely perform physical activities, or if you: Verify that the handlebar and seat clamps are closed and tightened to the torque specified in
the Manual.
are or may be pregnant;
Verify that both the handlebar latch and frame latch are secure and fully closed.
have heart, respiratory, back, joint, or other orthopedic conditions;
Check the tire pressure of both wheels.
have high blood pressure;
Pull the brake levers to ensure the brakes are working properly and adjust if necessary.
have difficulty with physical exercise;
NEVER exceed the maximum total weight limit of 330 lbs. (150 kg). The rear rack can hold a
have been instructed to restrict physical activity. maximum of 75 lbs. (35 kg). As an example, if you have 40 lbs. (18 kg) of cargo, then the maxi-
Always keep small parts away from children. Some eBike accessories may present a choking mum weight of the rider would be 290 lbs. (131 kg)
hazard to small children.
Follow eBike Regulations On and Off the Road
Never modify your frame or bicycle in any way. Do not sand, drill, file, or remove parts from
your bicycle. Do not install incompatible components or hardware. Be aware of eBike regulations in your area. Generally, the regulations for the use of an Aipas
bicycle are the same as those for a standard bicycle. However, there may be local differences
Always use proper lifting techniques to prevent injury. Your eBike may be significantly such as where you can ride, minimum rider age, or required equipment and license and
heavier than a bicycle without a battery pack and a motor. registration regulations. It is your responsibility to know the local regulations that apply to an
Take responsibility for your SAFETY. If you have any questions or do not understand any electric bicycle and to obey them.
aspect of using or maintaining your bicycle, contact Aipas eBikes at [email protected]
or call (833)532-5966 Ride at Your Own Risk and Use Common Sense
Do not ride distracted. Always remain alert to all riding conditions. Using the Display or other
technology (including your mobile phone or music player) could distract you from riding. Only
adjust the Display when stationary and in a safe start-up position.

04 05
 Safety Messages Icons and Stickers Guide

Always keep both hands on the handlebar grips and the brake levers so they are within reach Califomia Proposition 65
while riding.
WARNING! The wires of this product contain lead. Lead compounds and other chemicals
Never use headphones or a cell phone to talk or text when riding.
known to the State of California cause cancer and birth defects or other reproductive harm.
Always ride defensively. Watch out for potential obstacles that could force you to swerve Wash hands after handling.
suddenly or lose control. Braking while steering may reduce your ability to control your
bicycle.
Signal Wonds
Look ahead and brake sooner. You may be moving faster on your eBike, and it may be heavier,
compared to a bicycle, which means you may need to react and brake sooner when riding.
Indicates a hazardous situation that, if not avoided, will result in
Other road users may not expect you to be traveling at higher speeds. Riding faster may
DANGER death or serious injury.
increase your risk of a crash.
Stop pedaling well before approaching corners to avoid entering a corner too quickly. You
should also pay particular attention to terrain conditions as you may approach obstacles
faster than expected. Symbol
Alert Symbol. This symbol is used to alert you to potential
Riding in Wet Conditions personal injury hazards. Obey all safety messages that follow
this symbol to avoid possible serious injury or death.
Use caution when riding in wet conditions as it will take longer to brake and to stop. Your tires
may slip when turning. The risk of a crash is dramatically increased in wet conditions.

Your electric bicycle can withstand light rain and small splashes, but it is not designed to be
subjected to inclement weather, extremely heavy showers, or submersion in water. The
electric bike's components have an IP rating of 65. Damage caused by water damage will not
be covered by the warranty.

Riding at Night
Riding at night comes with more risks than riding during the day due to decreased visibility;
riders are encouraged to exercise increased caution in nighttime conditions.
Turn lights ON for safety. For increased visibility, ensure that the front headlight and rear
taillight are turned ON and adjusted so that other people on the road can see them clearly.
Also check your front, rear, and wheel reflectors.

Riders should wear reflective clothing at night. You may want to attach additional flashing
lights to your clothing or helmet.

06 07
 Icons and Stickers Guide Note Before Assembly

On-Product Waming Labels STARTING

Your bicycle comes fully assembled. These instructions are intended to assist you in setting up
There are warning labels on your Aipas eBike for your protection. If a label is missing or is not
and getting familiar with your new bicycle.
legible, contact Aipas eBikes for a replacement.
After you make your first adjustments and inspect your bicycle,
WARNING we recommend seeking professional help from a reputable and
certified bicycle mechanic to check your bicycle before your first

     ride.


   Before removing the packaging material from your bicycle, remove all items from the box and

 make sure you have the following:

 
 
­­­
What's in the box:
€­‚
­

ƒ„
 †‡
‚

Stem label Class 2 label Class 3 label

Aipas eBike Aipas eBike Charger Manufacturer Manuals Battery Keys

States that recognize three classes of eBikes require a label to be placed on the bicycle denoting
the class of your Aipas eBike, the motor’s wattage rating, and the top speed of your Aipas eBike. If anything is missing or is damaged, contact Aipas eBikes immediately for assistance.
Your bicycle comes as a Class 2 bicycle by default and has a label with this information posted For a video about visit our YouTube page: Aipas eBikes
under the carry-handle, near the seat post on the bicycle.

If you change your bicycle’s top speed, you must remove this label from the bicycle and replace Serial Number
it with a Class 3 label, detailing your Aipas eBike’s class, top pedal-assisted speed,and motor
Serial number is located on the head tube of the bicycle as shown below. Please write it down
wattage. The Class 3 label is put in the small box.
inside the front cover of this manual.You may be asked for your bicycle's serial number as part of
a warranty request, You may also be asked to provide this number to law enforcement if your
bicycle is stolen.

08 09
 Product Overview Setting Up Your Aipas eBike

NOTE: This manual is not intended to be an extensive reference book about service, mainte-

Front Mounting Point

Folding Stem Latch
nance, and/or repairs.You can find more information on our website: Aipasbike.com

Headlight Mount
Suspension Fork
3"Tire
Stem Clamp
Quick Plugs
Folding and Unfolding the Stem:

Head Tube
Head Set

Disc Rotor
Front Hub
Driveside
Crank
Top Tube
Frame Fold Latch

Pedal
Chainring
Display

Telescoping Stem

1 Begin with the handlebar in the folded 2 Push the latch firmly until it locks in
Tube
Seat

Crank Bolt
position, then pull the handlebar stem to position, then pull on it to confirm it is
Chain its upright position. secure and the handlebars cannot fold.
HALF-TWIST THROTTLE

Kick Stand
GEAR SHIFTER
LCD DISPLAY

DISPLAY CONTROL PAD

Rear Freewheel
Hub Motor
Rear Derailleur
Fender stay
Tail light
Fender
Seat Post Collar & clamp
Integrated Rear Rack
Seat Post
Saddle

1 Pull up on the silver button 2 Pull the latch away from 3 Fold the stem by lowering
labeled “open” to unlock the stem while still holding it to the side.
the latch. the “open” button.

10 11
 Setting Up Your Aipas eBike Setting Up Your Aipas eBike

Unfolding and Folding the Frame Unfolding and Folding the Pedal

1 Unfold the bike frame, and stand near 2 Push down the latch firmly until it locks 1 Rotate each pedal until you hear a click 2 Hold the pedal and gently push it towards
the frame where the battery is exposed. into position. Pull on the latch to confirm indicating it is locked in place, signifying the bike frame.
Grab the stem and rear end of the bike. that the latch has locked and that the that the pedal is fully unfolded.
Lift the bike slightly off the ground and frame cannot fold.
swing to the closed position.

1 Unlock the bike frame and 2 Pull the latch while still 3 Grab the frame near the 3 Turn the pedal to snap it into place
fold it by sliding the "open" holding the switch to the battery and fold the bike (perpendicular to the original pedal
switch to the right. “open” position. position), completing the folding process.

12 13
 Setting Up Your Aipas eBike Setting Up Your Aipas eBike

Adjust Stem Handlebar Height WARNING! Adjust seat Position WARNING!

Tighten fasteners to the correct torque to prevent serious injury or death. Bolts that are too tight
can cause the stem/seat post to stretch and deform. Bolts that are too loose can cause the stem/-
seat post to move and wear. Either condition can lead to a sudden failure of the bolt and result
in a crash. See Tightening Torque (p. 21).
A stem/seat post that is positioned too high can damage the bike and cause you to lose control
and crash. Select a height that is comfortable for you, but DO NOT extend past the safety line
position. To adjust your stem/seat post, unlatch the clamp, move the handlebars to the desired
height, and close the clamp. Re-tighten the stem/seat post clamp to the recommended torque
(see Tightening Torque on p. 21).

Front and back adjustment: Loosen nuts on both sides of the seat. Make sure the clamp mecha-
nism is clamping on the straight part of the seat rails and is not touching the curved part of the
rails. Ensure that you are using the recommended torque on the clamping fastener(s). See Tight-
ening Torque (p. 21).

Seat angle adjustment: Most people prefer a horizontal seat, but you may prefer the seat nose
angled slightly up or down. Loosen the clamp bolt to allow any serrations on the clamp mecha-
nism to disengage before changing the seat angle, and to fully re-engage the serrations before
you tighten the clamp bolt to the recommended Tightening Torque (p. 21).
Adjust Stem/Seat Post Heigh WARNING!

Loosen the lamp. The open and closed positions of the clamp are shown below (open position Remove The Battery
on left, closed position on right);
Raise or lower the stem/seat post in the seat tube;
Check if the seat/handlebar is straight and not tilted., and Re-tighten the seat post clamp to
the recommended torque. See Tightening Torque(p. 21).

1 Open the bike to its fully 2 Insert the key into the lock 3 Pull the latch and remove
folded state. and turn it to the "unlock" the battery
position.

14 15
 Setting Up Your Aipas eBike Specifications

Charge The Battery WARNING!

ITEM SPECIFICATIONS
1. The battery can be charged either by removing it from the bike or while it is installed on the
bike. Model AIPAS-A2

2. When charging the battery without removing it, first remove the dust plug located on the Product Dimensions 67*27*44(Inch)
frame, then insert the charging connector into the charging port.
3. When charging the battery after removing it, directly insert the charging connector into the Package Dimensions 38*16*29(Inch)
battery's charging port.
Max Load 350 Lbs
4. Typically, the charger’s indicator light shows red while charging, green when fully charged,
and also red when not charging. Package Weight 78 Lbs
You should fully charge the battery before your first ride.
E-Bike Weight 65 Lbs
Fire and explosion hazards. Never leave your battery battery unattended while
charging to prevent serious injury or death.
Max Speed 28 mph

Range 62 Miles

Battery 48V 11Ah

Charger 48V

Charging Time 4-5 Hours

Tire Pressure 23-25 PSI

Bell/Horn Electric Horn Installed

Motor 750W

Frame Material 6061 Aluminum frame

IP Level IPX 6

16 17
 LCD Display Controls LCD Display Controls

Operation Directions
Battery Indicator
Turn the bicycle ON/OFF Press and hold button

Increase PAS Level Press plus (+) button

Decrease PAS Level Press minus (-) button

Speed
Turn lights ON/OFF Press the button to turn on,
Press the button to turn off.
Press the button, and the horn will
Horn sound/stop
eBike Work Mlode sound. Release it, and the horn will stop.
&PAS Level Toggle Odometer, Trip A, Voltage,Current,
Press button
Trip Timer (TM)

Multifunction Press and hold the plus (+) button and )

Display Area button simultaneously to toggle between
Max Speed and Average Speed
the speed meter, max speed and average
speed.

NOTE: The trip meter, as well as maximum and average speed will reset when the bicycle is
ODO: Total mileage of the eBikem. Walk: Walking mode; powered OFF.
TRIP:Distance traveled during the current trip Cruise: Cruise control mode; To prevent serious injury or death, DO NOT change settings excluded from the table. Chang-
VOL: Curent working voltage ofthe battery TM: The total power-on time of the display ing setting not listed in the following table may cause your bike to stop working properly. If
you need the default setting values of settings not listed, contact Aipas eBikes. DO NOT ride
CUR: Current working current of the battery Error: An error has occuired with the eBike your bicycle until the default settings have been restored.
(see error code table for details)
Do not tamper with your bicycle. Tampering is defined as removing or replacing any original
equipment or modifying your bicycle in any way that may change its design and/or operation.
Such changes may seriously impair the handling, stability, and other aspects of the bicycle,
making it unsafe to ride. Tampering can void the warranty and render your bicycle non-com-
POWER BUTTON pliant with the applicable laws and regulations. Aipas eBikes is not responsible for any direct,
LIGHT BUTTON
incidental, or consequential damages, including, without limitation, damages for personal
injury,property damage, or economic losses due to tampering.
PLUS BUTTON
To change display settings, hold the plus (+) and the minus (-) buttons simultaneously to enter
HORN BUTTON into the Settings Menu. Press the button to toggle between each numbered setting. To adjust
MINUS BUTTON
the value of each setting, click the plus (+) and the minus (-) buttons as needed.
There are 21 settings (P01-P21). You should only change the settings listed below.

18 19
 LCD Display Controls Functions

Setting Function Default Explanation Tightening Torque Spec

Backlight display brightness.The darkest Bottom Bracket 60 Nm

P01 Brightness 2
level is 1 and thebrightest level is 3.
Brake Caliper Mounting Bolts 7 Nm
P02 Distance Units 1 0:KM; 1: MILE
Brake Lever Clamp Bolts 7 Nm
LCD Display sleep timer. The default setting
P04 Sleep 10 will turn the display OFF after it has not Crank Bolts 45 Nm
been used for 10 minutes.
Disc Rotor Mounting Bolts 7 Nm
Used to compute speed and distance
P06 Tire Size 22 traveled. Fender Mounting Bolts 6 Nm
Range is 0-100.The value represents the maximum
Headlight Mounting Screw 7 Nm
operating speed of your Aipas eBike in km/h. For
example,a value of 25 indicates the maximum Headset Parts 34 Nm
P08 Speed Limit 32 speed will notexceed 25 km/h. Drive speed is
maintained at this set value. Any value above 45 Kickstand Mounting Bolts 10 Nm
will fully unlock the bike’s speed, which equates to
up to 28mph. Margin of error: 3 km/h Pedals 10 Nm

0: Throttle active from standstill. Rear Derailleur Cable Clamp Bolt 4 Nmt
P09 Throttle Zero Start 0
1: Throttle active only whenalready moving.
Rear Derailleur Mounting Bolt 8 Nm
0: PAS Active, Throttle Inactive
P10 Mode Toggle 2 1: PAS Inactive, Throttle Active Rear Rack Mounting Bolts 7 Nm
2: Both PAS and Throttle Active
Seat Rail Binder 20 Nm
When set to higher numbers, it will take more
crank rotations for the motor to turn ON. Seatpost Clamp 9 Nm
P11 PAS Sensitivity 3
Lower numbers will take fewer crank
Shifter Clamp Bolt 5 Nm
rotations to turn the motor ON.

When set to higher numbers,the motor will Spokes 160-180(KGF)

P12 PAS Strength 1 come on stronger.Lower numbers will be
Stem Clamp Bolts 10 Nm
more gentle.

Restore Factory Press the (-) button for five seconds to Stem Plate 7 Nm
P16 Settings N/A restore factory settings.
Torque Arm Bolt 7 Nm
0: Walk Mode disabled
P21 Walk Mode Toggle 0 1: Walk Mode enabled Wheel Axle Nuts 40 Nm

20 21
 Functions Functions

7-Speed Gear System Suspension Fork

Your Aipas eBike comes with a 7-speed freewheel. The freewheel is the cluster of sprockets on Please check to ensure your suspension forks are properly adjusted for the terrain and your
the rear wheel of your bicycle. While pedaling in 1st gear (lowest gear using the largest sprocket), weight. The black knob does not have a function. The suspension fork will affect the handling of
it will be easier to pedal up hills. In 7th gear (highest gear using the smallest sprocket), it will be the bicycle, primarily when going over bumps and stopping. In some situations, it may be advan-
easier to reach higher speeds on flat or downhill terrain. tageous to lock the suspension so it is fully rigid.

Increase stiffness:
Turn the blue knob clockwise towards the"lock" direction indicated.
Throttle WARNING!
Reduce stiffness:
The right handlebar features a twist throttle.
Turn the blue knob counterclockwise towards the"open" direction. indicated.
Check that the Pedal Assist (PAS) level is set above 0, then twist the throttle back slowly to Fully lock suspension:
achieve your desired speed and acceleration. Turn the knob clockwise towards the"lock" direction indicated until it cannot be turned further.

Mechanical Disc Brakes WARNING! Push the minus (-) lever

forward to shift down
Your Aipas is equipped with mechanical disc brakes.
To brake the front wheel:
Pull the left brake lever to activate the front brake.
To brake the rear wheel:
Pull the right brake lever to activate the rear brake.

Push the plus (+) button to shift up

Front and Rear Lights How To Use Pedal Assist

Your Aipas eBike comes with integrated front and rear lights. Pedal Assist (PAS) functions only when you are pedaling. If you do not pedal, the PAS will not
activate. The motor output always depends on your pedaling and the PAS level you have set.
To turn lights ON: Press the button to turn on. PAS automatically switches off at the maximum speed set for your Aipas eBike (up to 28 mph).
When the speed falls below the maximum set speed, PAS automatically becomes available
To turn lights OFF: Press the button to turn off. again.
You can also use your Aipas eBike as a normal bicycle without assistance at any time, either by
turning off the display or by setting the PAS level to 0. PAS will not function if the battery is
discharged.

When the bicycle has not been used for 10 consecutive minutes, the display will automatically
shut down. The PAS and throttle features will no longer work when the display is OFF.

22 23
 Functions Warning Messages

Walk Mode Frame

Electric bicycles are heavier than bicycles. To make walking the bicycle easier, your Aipas is Never modify your frame or bicycle in any way as this could cause serious injury or death. Do not
equipped with Walk Mode, which can be toggled on or off in the settings menu. Walk Mode may sand, drill, file, or remove parts from your bicycle. Do not install incompatible components or
be subject to local regulations. Check your local regulations to determine if it is allowed. hardware.

To activate:
Motor & Electric System
Hold down the minus (-) button on the display control pad and the motor will engage at a speed
similar to a slow walk. Do not open the drive unit yourself. The drive unit must only be repaired by qualified personnel
using only original parts. This will ensure that the safety of the drive unit is maintained.
To deactivate:
Unauthorized opening of the drive unit will render warranty claims null and void.
Pull either brake lever to disengage Walk Mode OR press and hold the minus (-)button on the
display control pad. All components fitted to the drive unit and all other components of your Aipas eBike PAS system
(e.g. chaining, chaining receptacle, pedals) must only be replaced with identical components or
NOTE: When Walk Mode is active,"Walking" will appear on the display. components that have been specifically approved by Aipas eBikes. This should help protect the
motor from overloading.
Cruise Control Always remove the battery pack from your Aipas eBike before beginning work (e.g. inspection,
repair, assembly, maintenance, work on the chain, etc.), transporting it with a car or on an
Cruise control on your Aipas works similarly to cruise control on a car. The bike will try to main-
airplane, or storing it. Battery pack removal should prevent unintentional activation of your Aipas
tain a speed based on the position of the throttle when cruise control is activated. For example,
eBike.
if the throttle is twisted all the way from its resting position (to a position that would normally
Do not make any modifications to your Aipas eBike or attach any other products that might
maintain 20 mph) and the minus button is held, cruise control will be activated and set at 20
increase the performance of your Aipas eBike. Doing so will generally reduce the service life of
mph. Even if the bike is currently going slower than 20 mph, the bike will try to accelerate and
the system and risks damaging the drive unit and the bicycle. You also run the risk of losing the
maintain that speed because it was set based on that throttle position.
guarantee and warranty claims on the bicycle you have purchased.
To activate: Under extreme conditions, such as continuously high loads at low speeds when riding up hills or
Hold the minus (-) button while twisting the throttle. carrying loads, parts of the motor can reach high temperatures.
To cruise at low speeds, only slightly twist the throttle and hold the minus (-) button.

NOTE: When Cruise Control is active, “Cruise" will appear on the display. Brake System
To deactivate: ALWAYS apply the right brake lever (rear wheel) before and during the use of the front brake.AL-
Pull either brake lever to disengage Cruise Control. WAYS apply even pressure to both brake levers when blowing down or stopping. If only the front
brake is applied while slowing or stopping quickly, you may be ejected over the front handlebars.
Before riding, check to ensure brake levers do not touch the handlebars when fully applied, If
either lever touches the handlebars screw or unscrew the barrel adjuster to increase tension in
the brake cable. If this does not fix the problem, take your bicycle to an experienced bicycle
mechanic for further adjustment.
Disc brake rotors will become hot during use and will stay hot for a short period after use. To
prevent burns, do not touch the disc rotor right after use.

24 25
 Warning Messages Warning Messages

Electrical Components Tips to Increase Range

Always turn lights ON for your safety, especially when riding at night or in low visibility situations. To get the maximum range out of each battery charge, there are some simple things you can do:
Set the display brightness such that you can adequately see important information like speed or Ride at a lower PAS level
warning symbols. Display brightness that is incorrectly set can result in dangerous situations.
Use lower PAS levels and pedal when climbing hills
Do not allow yourself to be distracted by the display. If you do not concentrate on the traffic Pedal when starting from a standstill
around you, you risk being involved in a crash. If you want to change any settings other than the
PAS level, always stop before changing the settings or display.
Battery
Range Estimates Only place the battery pack on clean surfaces. Avoid getting dirt, e.g.sand or soil, in the charging
The range the bicycle can go on a single battery charge can vary significantly between riders, port and contacts.
terrain, wind conditions, user input, and additional cargo weight. The following table shows Do not charge or use a battery pack if it is damaged. Contact AipaseBikes to order a replace-
estimates of potential ranges riders may expect in different conditions. ment.
When unlocking and removing your battery pack from the frame, take care that it does not slide
All tests were performed with: out while the bicycle is folded. If your battery impacts the ground and is damaged, discontinue
use and contact Aipas eBikes immediately.
Flat ground Few starts and stops Rider weight ~180 lbs

Few bumps No additional cargo Top speed set to 20 mph Top Speed
Little to no wind Temperature ~75°F CST BFT tires at ~30 PSI Your Aipas eBike ships with a maximum speed set at 20 miles per hour (mph). This means it is a
Class 2 electric bicycle in states that recognize three classes of eBikes. In most states that only
recognize eBikes generally, the 20 mph top speed is legal for use on public roads.

Class Pedal Assist Speed Limit Throttle Speed Limit

1 20 mph Throttle not allowed

2 (Default) 20 mph 20 mph

3 28 mph 20 mph

Ride within your limits to prevent serious injury or death. Riding at higher speeds poses an
increased safety risk. ALWAYS wear a helmet and obey the rules of the road.
NOTE: This setting represents the top speed in kilometers per hour. For Class 2 performance, this
speed setting must not exceed 20 mph (32 km/h). For Class 3 performance, this setting will be
set at 100, indicating the bike has been completely unlocked to enable speeds of up to 28mph.

26 27
 Thinks To Know Before The Ride Thinks To Know Before The Ride

Things To Check How To Start And End Your Ride

Check your eBike to ensure the front axle, the rear axle, the handle-bars, and the seat are 1. Insert key and turn counterclockwise to the ON position. The key will be parallel with the
secure. frame and you will not be able to remove the key from the battery pack.
Check that both the handlebar latch and frame latch are fully closed and locked.
2. Hold down the button located on the left handlebar until the display comes on.
Check the tire pressure of both wheels.
3. Select a Pedal Assist (PAS) level using the plus (+) and minus (-) buttons. PAS 0 provides no
Pull the brake levers to make sure your brakes are working properly and adjust them if necessary. motor assist. PAS 1 is the lowest level of assist and PAS 5 is the highest level of assist.
NEVER exceed the maximum total weight limit of 330 lbs. (150 kg). The rear rack can hold a
4. When the bicycle is at a complete stop, press and hold the button to turn the display OFF. This
maximum of 75 lbs. (35 kg). As an example, if you have 40 lbs. (18 kg) of cargo, then the maxi-
ensures the motor will not activate until the display is turned ON again and you are ready to
mum weight of the rider would be 290 lbs. (131 kg)
ride.
Only carry the cargo you need. More weight will drain the battery faster and affect how the bike
handles. Note:Exercise extreme caution when using the twist throttle. When at a complete stop with
Ensure all components are properly secured. the bicycle power ON, be careful not to twist the throttle, or the bicycle could accelerate and
cause you to crash.
Make sure your battery is fully charged.
Do not engage in Walking Mode when riding or sitting on your Aipas eBike. Holding the minus
Please secure your helmet.
(-) button will engage the motor up to a walking speed.

Safety Tips
The acceleration of your eBike might be faster than anticipated and may feel unadaptable at
first. Before your ride, Please use the lowest level of pedal assist (PAS 1) and become familiar with
the operation of your Aipas eBike by practicing starting, stopping, cornering, and navigating
obstacles in a safe environment away from other bicycles, pedestrians, and/or vehicles. You
should also pay particular attention to terrain conditions as you may approach obstacles faster
than expected.

The Pedal Assist may be activated as soon as you step onto the pedals and the bicycle is in
motion. ALWAYS be seated on the bicycle and engage at least one brake before starting to pedal.
DO NOT place one foot on a pedal then throw your other leg over the bicycle or your eBike could
accelerate unexpectedly.

28 29
 Battery Safety Battery Safety

Battery pack refers to all original Aipas eBikes battery packs. Battery charging times may increase with battery age and usage.
The safety of both our customers and our products is important to us. Our eBike batteries are Only grab the charger by the plug and not the cable when plugging and unplugging from the
lithium-ion batteries, developed and manufactured with the latest technology. We comply with wall.
or exceed the requirements of all relevant safety standards. When charged, these lithium-ion
If the battery has trouble charging, stop charging and contact Aipas eBikes immediately.
batteries contain a high level of energy. If a fault occurs (which may not be detectable from the
outside), in very rare cases and under unfavorable conditions, lithium-ion batteries can catch fire. Do not puncture or crush the battery pack. Do not impact the battery pack or modify it in any
Take care when using and charging your battery. Failure to follow the guidelines below could way. Do not use the battery pack if it shows visible damage. The aforementioned can increase
damage property and/or serious injury. Contact Aipas eBikes immediately if you have any the danger of fire or explosion.
questions regarding battery safety. Protect the battery pack from heat (e.g., temperature >140ºF), fire, and immersion in water.
Your Aipas eBike battery must not be opened, even for repairs. There is a risk your eBike battery The aforementioned can increase the danger of fire or explosion.
could catch fire, e.g. due to a short circuit. This risk increases if an eBike battery that has already Always remove the battery pack before beginning work (e.g. inspection, repair, assembly,
been opened is reused at a later point in time. Do not attempt to repair an eBike battery in the maintenance, work on the chain, etc.) on your Aipas eBike, transporting it via car or airplane,
event of a fault. Have it replaced with an original Aipas eBike battery pack. or storing it. Unintentional activation of the Aipas eBike poses a risk of injury.
The battery is protected against deep discharge, overloading, overheating, and short-circuiting Do not open the battery. There is a risk of short-circuiting. Opening the battery voids any
by Electronic Cell Protection (ECP). In the event of a fault, a protective circuit switches the warranty claims.
battery pack off automatically.
When the battery is not in use, keep it away from paper clips, coins, keys, nails, screws, or other
Only use original Aipas eBike batteries for your eBike. Using other batteries can lead to injuries small metal objects that could make a connection from one terminal to another. A short
and pose a fire hazard. Aipas eBikes accepts no liability or warranty claims if other batteries are circuit between the battery terminals may cause burns or a fire. Short circuit damage which
used. occurs in this instance voids any warranty claims against Aipas eBikes.

To prevent serious injury or death: Avoid mechanical loads and exposure to high temperatures. These can damage the battery
cells and cause the flammablecontents to leak out.
Do not leave your battery unattended while charging.
Do not place the charger or the battery near flammable materials. Ensure the battery is
When removing the battery, unplug the rubber stopper on the charging point.
completely dry and placed on a fireproofsurface before charging. There is a risk of fire due to
Please remove the battery from the bicycle when not in use and store in a secure location to the heat generated during charging.
prevent unauthorized use.
Your Aipas eBike battery must not be left unattended while charging.
Please do not submerge the battery in liquid of any kind.
If used incorrectly, liquid may leak from the battery. Contact with this liquid should be avoid-
Do not touch the terminals on your battery.
ed. If contact occurs, rinse off with water. If the liquid comes into contact with your eyes, seek
Turn the display OFF when not in use and before removing the battery pack. additional medical attention. Liquid leaking from the battery may cause irritation or scalding.
Battery leakage may occur under extreme usage or temperature conditions. Avoid contact Batteries must not be subjected to mechanical shock. If the battery is dropped or struck with
with skin and eyes. Battery liquid is caustic and could cause chemical burns. If battery liquid another object, the battery may be damaged.
comes in contact with the skin, wash quickly with soap and water. If the liquid contacts your
The battery may give off fumes if it becomes damaged or is used incorrectly. Ensure the area
eyes, immediately flush eyes with water for a minimum of 15 minutes and seek medical atten-
is well-ventilated and seek medical attention if you experience any adverse effects. The fumes
tion. The battery pack should not be excessively difficult to insert or remove. Do not force the
may irritate the respiratory system.
battery pack in or out of the bike frame.

30 31
 Battery Safety Charge Safety

Only charge the battery using the original Aipas eBikes chargers. When using chargers that Locate the charge port on the side of the battery. You can charge the battery from this port while
are not made by Aipas eBikes, the risk of fire cannot be excluded. the battery is in or out of the bicycle.

Use the battery only in conjunction with your Aipas eBike. This is the only way in which you Do not leave your battery unattended while charging.
can protect the battery against dangerous overload.
Do not connect the battery pack to the charger until it has reached an allowable charging
Use only the original Aipas eBikes battery packs that the manufacturer has approved for your temperature.
eBike. Using other batteries can lead to injuries and pose a fire hazard. Aipas eBikes accepts
Do not charge the battery with chargers other than the charger provided by Aipas eBikes.
no liability or warranty claims if other batteries are used.
Only charge the battery indoors and in dry spaces that are not excessively hot or cold (with-
Keep the battery away from children.
in 10ºF of room temperature).
Always turn the display OFF before removing the battery pack. Ensure there are no flammable items, dirt, or debris nearby when using the charger.

Always remove the key from the battery pack after each use. This prevents both unauthorized The charger will automatically stop charging once the battery reaches its full capacity.
use of the powered features of your Aipas eBike and removal of the battery by unauthorized The light on the charger will be red when the battery is charging and will turn green when
persons when your Aipas eBike is not in use. Failure to secure your bicycle from unauthorized charging has finished.
use can result in death or serious injury to others.
Avoid leaving the charger plugged in when the battery is fully charged.

Do not charge the battery if you notice the battery is damaged, excessively hot, leaking,
smells, or is discolored.

Charging the battery should take approximately 4-6 hours if the battery is mostly empty.
Store the battery indoors in a dry space, away from heat or flame sources, and out of direct
sunlight.

The charger may get hot (>165°F) when charging. Use caution and avoid touching the body of
the charger.
To reduce the risk of injury, charge only the batteries of your Aipas eBike. Other types of
batteries may burst, causing personal injury and damage.
Only charge Aipas eBikes-approved lithium-ion battery packs. The battery pack voltage must
match the battery pack charging voltage of the charger. Otherwise, there is the risk of fire and
explosion.

Only use the original Aipas eBikes battery charger supplied with your eBike or one approved
for your eBike by the manufacturer and purchased from a trusted source. Bypassing the
battery charger or the use of a non-approved or counterfeit battery charger can lead to death
or serious injury.

Do not expose the charger to rain or wet conditions. If water enters a charger, there is a risk of
electric shock.

32 33
 Charge Safety Storing The Battery

Keep the battery charger clean. Contamination can lead to the risk of an electric shock. Clean Note of storing
only with the use of a damp cloth (mild soap/water).
Charging Battery Pack Before and During Storage
Always check the charger, cable, and plug before use. Stop using the charger if you find any
damage. Do not open the charger. Damaged chargers, cables, and plugs increase the risk of When the battery pack will not be used for weeks or months, remove it from the eBike and store
electric shock. the battery pack at about 60 % charge as indicated by the Energy Bar on the display. At about
Do not operate the charger on easily ignited surfaces (e.g., paper, textiles) or in flammable 60% charge, the battery will degrade less, compared to higher charge levels. Every 2-3 months
environments. The charger may heat up and cause a fire. check the battery charge level and recharge to 60%, if necessary.

Take care if you touch the charger while it is charging. The charger can get very hot, especially Note: If the battery is stored at no charge for an extended period of time, it may be damaged
when the ambient temperature is high. despite the low self-discharge and may reduce the battery capacity.

If the battery gives off fumes due to damage or incorrect use, ventilate the area and seek For optimum service life for your battery pack, charge the battery pack to 100% a few hours
medical attention if needed. These fumes can irritate the respiratory tract. before you plan to ride. For example, if you ride the bicycle and the charge level falls to 50% but
you plan to use the bicycle again in a few days, wait until the day before you plan to use it again
Batteries must not be subjected to mechanical shock. There is a risk of damage to the battery
to charge it to 100%.
pack.
DO NOT charge the battery unattended or leave the battery connected to the charger
Keep the battery charger away from children. This will ensure that children do not play with
overnight.
the charger.
Leaving the battery permanently connected to the charger is not recommended.
Persons who cannot safely operate the charger due to physical, sensory, or mental limitations,
As the battery pack ages, capacity will diminish and the battery pack will eventually need to be
or due to lack of experience or knowledge, should only use it under supervision or after
replaced. A significantly reduced operating period after charging indicates that the battery pack
instruction by a responsible person to avoid operating errors and injuries.
is worn out and must be replaced. You may replace it yourself by purchasing a replacement
Note the household voltage! The voltage of the power supply must correspond to the specifi- battery pack from Aipas eBikes.
ca-options given on the battery charger nameplate.
Storage Conditions
To Charge:
If possible, store the battery pack in a dry, well-ventilated place. Protect it from moisture and
Plug the cable from the charger into the port on the side of the battery pack. water.Always store your Aipas eBike battery pack in a location that:
Plug the charger power cable into an electrical mains wall socket. Use only the supplied input
The battery is in a room with a smoke alarm;
connection: standard AC power cord when connecting to the household electrical supply.
The battery is away from combustible or easily flammable objects;
Note: The charging process is only possible when the temperature of your Aipas eBike battery is The battery is away from heat sources.
within the permitted charging temperature range.
For an optimum service life, store your Aipas eBike battery at temperatures between 50º F and
Note: PAS is deactivated during the charging process. 68º F. Never store it at temperatures below 14º F or above 140º F. Make sure the maximum
After charging is complete and the light on the charger is green, disconnect the cable from the storage temperature is not exceeded. Do not leave the battery in your car during the summer, for
battery port and the power cord from the wall socket. If you have charged the battery in the example, and store it away from direct sunlight.
bicycle frame, carefully insert the plug after charging, so that no dirt or water can enter the
NOTE: Leaving the battery installed on the bicycle for long-term storage is
battery port.
not recommended.
34 35
 Troubleshooting Maintenance

Note: Our warranty does not include any maintenance fees

Issue Most Common Solutions
1. Charge the battery until the light onthe charger turns You should have your bicycle maintained at regular service intervals at your local bicycle shop.
from red to green.This may take up to 8 hours. NEVER open any of the components, including the battery, display, motor, or PAS sensor. Service
2. Insert key in the battery and turncounterclockwise to should only be performed by a bicycle repair shop.
the ON positionor until the key is parallel with theframe. Always remove the battery pack before performing any bicycle inspection, maintenance, or
Then press and hold the bbutton to turn ON. repair.

Bicycle will not turn ON. 3. Follow the cable coming from thedisplay down to the If you suspect that something is loose, do not ride your bicycle. All nuts, bolts, and screws require
quick plug. Youmay need to unravel some of theplastic the proper tightening force. Too little force and the fastener may not hold securely. Too much
wrapping to access it. With aquick pull (do not twist), force and the fastener can strip threads, stretch, deform, or break. Either way, incorrect tighten-
unplug thequick plug, inspect both sides of theplug, and ing force can result in component failure, which can cause you to lose control and crash. Take
reconnect by lining up thearrows on both ends. After your bicycle to a bicycle repair shop for service.
checkingthe quick plug, press and hold the bbutton on
the display control pad toturn on. Do not paint any components of your Aipas eBike as they may cause premature failure of the
component.
1. Check that the PAS level is setbetween 1-5.
Do not submerge your Aipas eBike or its components in water use a pressure washer to clean it.
Pedal assist or throttle do 2. To test if PAS is working, do notoperate throttle.
not work. 3. To test if the throttle is working, donot pedal. Always observe the operating and storage temperatures of your Aipas eBike and its components.
4. Check all quick plugs. Protect motor, display, and battery pack against extreme temperatures (e.g. from intense
sunlight without adequate ventilation). Extreme temperatures can damage components (espe-
cially the battery pack). Please have your Aipas eBike serviced at least once a year.
Error Codes
The components of your Aipas eBike are continuously monitored automatically. If a fault is
detected, the error code will appear on the display.

Error Code Meaning Most Common Solution

E003 PAS Sensor Fault Check PAS quick plug

E006 Battery Under-voltage Fully charge battery

E007 Motor Fault Check motor quick plug

E008 Throttle Fault Check throttle quick plug

E009 Controller Fault Check controller connections

E010 Display,Communication,Reception Failure Check display quick plug

E011 Display,Communication,Send Failure Check display quick plug

36 37
 Maintenance Legal Warranty

Aipas ebikes warrants to the original registered purchaser that Aipas ebikes shall be free from all
Inte al Inspect Se ice Replace
defects in material and workmanship for a period of one year from the date of purchase.

Check drivetrain for proper alignment

disclaimer of consequential and incidental damages: the original registered purchaser of this
and function (including the chain, bike, subsequent owners, and all other intended and unintended users of this bike, shall not be
freewheel, chainring,and derailleur). Clean frame by wiping frame Replace any components
Weekly, own with damp cloth. confirmed by Aipas entitled to recover from Aipas ebikes any consequential or incidental damages. there is no
100-200 mi Check wheel trueness and for quiet Product Support or a warranty of merchantability or fitness for a particular purpose. The warranty is non-transferable
(160-321km) wheel operation (without spoke noise). Use barrel adjuster(s) to certified,reputable bike
tension derailleur/brake cables mechanic to be damaged and only applies to the original owner. This warranty gives you specific rights and purchasers
Check condition of frame for any if needed. beyond repair or broken. may also have other rights, which may vary from state to state. Damage caused by failing to
damage.
follow instructions in the manual, acts of God, accident, misuse, neglect, abuse, commercial use,
alterations, modification, improper assembly, installation of parts or accessories not originally
intended or compatible with the Aipas eBike as sold, operator error, water damage, extreme
Check brake pad alignment, brake
cable tension.
riding, stunt riding, or improper follow-up maintenance is not covered under this warranty.
Clean and lubricate drivetrain.
Check bike is shifting properly, proper Warranty parts will only be shipped within the continental United States.
derailleur cable tension. Check crankset and pedal
Replace brake and shift
torque.
Monthly,
Check chain stretch. cables if necessary. Parts covered by the warranty: frame, forks, stem, handlebars, headset, seat post, saddle, brakes
250-750 mi Check brake and shifter cables for Clean brake and shift cables. (excluding brake pads), lights, bottom bracket, crank set, pedals, rims, wheel hub, freewheel,
corrosion or fraying. Replace brake pads if
(402-1207km) True and tension wheels if any necessary. cassette, derailleur, shifter, motor, throttle, controller, wiring harness, display (excluding damage
Check spoke tension. loose spokes are discovered.
due to water), kickstand, reflectors, and hardware. The battery warranty does not include
Check accessory mounting (rack
mounting bolts, fender hardware, and Balance the battery. damage from power surges, use of 3rd party charger, improper maintenance or other such
alignment). misuse, normal wear, or water damage (including rust).

Accessories sold on Aipasbike.com are not covered under warranty.

Stolen bikes are not covered under warranty.

Replace brake pads.
Standard tune-up by
Inspect drivetrain (chain, chainring, certified,reputable bike Replace tires if necessary.
Necessary precautions must be taken to ensure the bike and battery are not exposed to severe
Months, freewheel, and derailleur). mechanic is recommended.
750-1250mi
weather conditions. Exposure to very wet, hot, or cold conditions may void the warranty. Aipas
Replace cables and
(1207-2011km) Inspect all cables and housings. Grease bottom bracket. housings if necessary. eBikes will replace any parts deemed to have been damaged during shipping. Shipping damage
must be reported to Aipas eBikes within 14 days of shipment arrival. This applies to all products,
including bikes and accessories.

You will NOT be refunded as compensation for your time or efforts in replacing damaged parts.

Replacement parts will not be sent until photographic evidence has been provided to Aipas
eBikes. Aipas eBikes may request additional documentation (such as video) to assist with
accurately diagnosing the problem and processing the warranty claim.

Most warranty parts are fulfilled 1-10 business days after the request is put into our system by a
customer service representative. Warranty parts are sent using USPS First Class, FedEx Express,
or FedEx Ground, depending on the size of the part. Warranty parts will not be expedited.

38 39
 Legal Warranty Legal Warranty

Items including the chain, tires, wheels, rims, tubes, battery handle, brake rotors, brake pads, Liability Disclaimer
cables and housings, grips, and spokes are considered wear items. These items wear down with Riding any kind of bicycle comes with inherent risks and dangers that cannot be predicted or
normal use and are not covered under warranty. You are responsible for replacing and maintain- avoided. These dangers could result in a serious accident, injury, or death of the rider. It is the sole
ing these worn items. responsibility of the rider to become properly educated and prepared to ride safely. Once in
possession of the bike, Aipas eBikes strongly encourages and recommends that all customers
Any unauthorized alterations or repairs are not covered and may void this warranty. have a certified and reputable bicycle mechanic complete a full inspection of each component
on the bicycle to ensure it is safe for operation. Aipas eBikes makes no claims or guarantees that
For warranty services, please contact Aipas eBikes’ online support by email at service@aip-
the brakes, battery, frame, motor, motor controller, display, electrical cables, electrical cable
as-bike.com. Bikes or parts returned without proper documentation may result in delayed
housings, fasteners, grips, fork, stem, shifters, headset, seat post, seat post clamp, handlebar stem
service or denied warranty coverage. Warranty return shipping costs along with duties and taxes
clamp, saddle, wheel hubs, handlebars, spokes, rims, tires, tubes, derailleur, freewheel, cassette,
are the responsibility of the claimant. All unauthorized returns will be refused.
throttle, kickstand, lights, reflectors, hardware, bottom bracket, or any other part or accessory,
will be properly secured and adjusted upon arrival. Before every ride, fully inspect your bicycle to
Note that your insurance policies may not provide coverage for accidents involving Aipas eBikes.
ensure everything is secured and adjusted properly.
To determine if coverage is provided, you should contact your insurance company or agent.
Damage as a result of an accident is not covered under this warranty, and Aipas eBikes is not
responsible for the repair or replacement of damaged bikes or parts.

Aipas eBikes reserves the right to change its warranty at any time and without notice.

Any action, lawsuit, or other proceeding, under this warranty or otherwise related to the bike
must be commenced within ninety (90) days after expiration of the one-year warranty period.
Performance Disclaimer

The bikes listed range and top speed are estimates (not guarantees) of expected performance.
Performance will vary with rider weight, cargo weight, rider/cargo shape (both contribute to
drag), terrain, tire pressure, brake adjustment, throttle vs PAS usage, pedal power, battery charge
level, ambient temperature, and wind conditions. Under certain conditions, it is possible to get
ranges and top speeds that are different from the listed estimates.

40 41
 FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:

This device may not cause harmful interference

This device must accept any interference received, includinginterference that may cause
undesired operation.

Please note that changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits of a Class B digital device,
under part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. lf this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the follow-
ing measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver
Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.

Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with radio frequency exposure limits set forth by the FCC for an
uncontrolled environment.

This equipment should be installed and operated with a minimum distance of 5 mm between
the device and the user or bystanders.

This device must not be co-located or operating in conjunction with any other antenna or
transmitter.

42